APPENDIX 4 TYPICAL LAYOUT, VALUES AND CONSTANTS

Size: px
Start display at page:

Download "APPENDIX 4 TYPICAL LAYOUT, VALUES AND CONSTANTS"

Transcription

1 109 APPENDIX 4 TYPICAL LAYOUT, VALUES AND CONSTANTS TYPICAL LAYOUT The purpose of a transformer is to transfer energy from the input to the output through the magnetic field. The layout of a partial typical core type transformer is shown in Figure A4.1. Figure A4.1 Typical layout of a transformer

2 110 OVERALL DIMENSIONS The overall dimension of a three phase core type transformer and a single phase shell type transformer is as shown in Figure A4.2(a) and A4.2(b) respectively. (a) Three phase core type transformer (b) single phase shell type transformer Figure A4.2 Overall dimensions of a transformer YOKE Area of yoke for hot rolled silicon steel is 15 to 25% greater than the core area. For cold rolled silicon steel, the area of yoke is equal to area of core. The section of yoke can either be taken as rectangular or it may be stepped. The yoke sections are shown in Figure A4.3.

3 111 Figure A4.3 Yoke cross sections FLUX DENSITY The usual values of maximum flux density B m for transformers using hot rolled silicon steel are: Distribution Transformers to 1.35 Wb/ Power Transformers to 1.45 Wb/ Lower values should be used for small rating transformers. For transformers using cold rolled grain oriented steel, the following values may be used: For transformers upto 132 kv Wb/ For 275 kv transformers Wb/ For 400 kv and generator transformers Wb/

4 112 CURRENT DENSITY The range of value of current density is as follows. For distribution and small power transformers to 2.3 A/ m self oil cooled type upto 50kVA Large power transformers, self oil cooled type to 3.2 A/ m or air blast Large power transformers with forced circulation to 6.2 A/ m of oil or with water cooling coils For minimum copper loss, the value of current density in each of the two windings should be equal. However, the current density in the relatively better cooled outer winding is made 5% greater than the inner winding. STACKING FACTOR The iron stacking factor, K i = 0.9 WINDOW SPACE FACTOR The following empirical formulae may be used for estimating the value of window space factor, K w Transformers of ratings Kw 10 (30 kv) between 50 to 200 kva

5 113 Space factor is large for large outputs and smaller for small outputs. For a transformer about 1000 kva, Kw 12 (30 kv) For a transformer about 20 kva, Kw 8 (30 kv) interpolated. The value of space factor for intermediate ratings can be LEAKAGE REACTANCE Long and thin coils give low value of leakage reactance and short and wide coils give large value of leakage reactance. WINDOW The ratio of height to width of window, Hw Ww is between 2 to 4. The width of window for maximum output is 0.7d. TRANSFORMER CONSTANT The value of transformer constant K for different types of transformers are given in Table A4.1. Table A4.1 Transformer constant, K Type Three phase core type (Distribution) Three phase core type (Power) Single phase core type Single phase shell type Three phase shell type K to to to

6 114 RATIO OF WEIGHTS in Table A4.2. The general ratio of weight of iron to weight of copper is indicated Table A4.2 Ratio G i G c Distribution Transformers Type G G c i Single phase core type transformers (Small capacity) High voltage power transformers 1.5 to 3 < times above value RATIO OF LENGTHS Typical values of ratio L mt / l i is given in Table A.4.3 Table A4.3 Ratio L /l mt i Three phase core type Single phase core type Single phase shell type Type L /l mt i 0.17 to to to 2.0 MULTI-STEPPED CORE The most economical dimensions of various steps for a multistepped core is given in Table A4.4.

7 115 Table A4.4 Dimensions of core steps Area percentage of circumscribing circle Gross Core Area, A gi Net core area, A i Net core area, A i = K c d 2 Square Cruciform Three stepped Four stepped K c LOSS CURVE This curve is used to obtain specific iron loss and is shown in Figure A4.4 for different types of steel having 0.35 mm thick laminations. Figure A4.4 Loss curve The above are the typical values and constants used in the conventional design method of a transformer.

8 116 B at or B-H CURVE The B- at curves as supplied by sankey pressings Division of m/s Guest Keen Williams Ltd is shown in Fig. A4.5. The curve may be used to find the mmf required to establish the flux. Figure A4.5 B- at Curves

GOVERNMENT COLLEGE OF ENGINEERING, BARGUR

GOVERNMENT COLLEGE OF ENGINEERING, BARGUR 1. Which of the following is the major consideration to evolve a good design? (a) Cost (b) Durability (c) Compliance with performance criteria as laid down in specifications (d) All of the above 2 impose

More information

PROBLEMS on Transformers

PROBLEMS on Transformers PROBLEMS on Transformers (A) Simple Problems 1. A single-phase, 250-kVA, 11-kV/415-V, 50-Hz transformer has 80 turns on the secondary. Calculate (a) the approximate values of the primary and secondary

More information

TRANSFORMERS PART A. 2. What is the turns ratio and transformer ratio of transformer? Turns ratio = N2/ N1 Transformer = E2/E1 = I1/ I2 =K

TRANSFORMERS PART A. 2. What is the turns ratio and transformer ratio of transformer? Turns ratio = N2/ N1 Transformer = E2/E1 = I1/ I2 =K UNIT II TRANSFORMERS PART A 1. Define a transformer? A transformer is a static device which changes the alternating voltage from one level to another. 2. What is the turns ratio and transformer ratio of

More information

UNIVERSITY OF TECHNOLOGY By: Fadhil A. Hasan ELECTRICAL MACHINES

UNIVERSITY OF TECHNOLOGY By: Fadhil A. Hasan ELECTRICAL MACHINES UNIVERSITY OF TECHNOLOGY DEPARTMENT OF ELECTRICAL ENGINEERING Year: Second 2016-2017 By: Fadhil A. Hasan ELECTRICAL MACHINES І Module-II: AC Transformers o Single phase transformers o Three-phase transformers

More information

Walchand Institute of Technology. Basic Electrical and Electronics Engineering. Transformer

Walchand Institute of Technology. Basic Electrical and Electronics Engineering. Transformer Walchand Institute of Technology Basic Electrical and Electronics Engineering Transformer 1. What is transformer? explain working principle of transformer. Electrical power transformer is a static device

More information

86 chapter 2 Transformers

86 chapter 2 Transformers 86 chapter 2 Transformers Wb 1.2x10 3 0 1/60 2/60 3/60 4/60 5/60 6/60 t (sec) 1.2x10 3 FIGURE P2.2 2.3 A single-phase transformer has 800 turns on the primary winding and 400 turns on the secondary winding.

More information

Subject: Computer Aided Electrical drawing (CAED) Subject Code: 10EE65

Subject: Computer Aided Electrical drawing (CAED) Subject Code: 10EE65 Subject: Computer Aided Electrical drawing (CAED) Subject Code: 10EE65 Syllabus Covered Part-B 3. Electrical machine assembly drawing using design data or sketches or both (a) Transformers- sectional views

More information

COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING ACADEMIC YEAR / EVEN SEMESTER QUESTION BANK

COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING ACADEMIC YEAR / EVEN SEMESTER QUESTION BANK KINGS COLLEGE OF ENGINEERING DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING ACADEMIC YEAR 2010-2011 / EVEN SEMESTER QUESTION BANK SUBJECT CODE & NAME: EE 1352 - ELECTRICAL MACHINE DESIGN YEAR / SEM

More information

Outcomes from this session

Outcomes from this session Outcomes from this session At the end of this session you should be able to Understand what is meant by the term losses. Iron Losses There are three types of iron losses Eddy current losses Hysteresis

More information

CHAPTER 2. Transformers. Dr Gamal Sowilam

CHAPTER 2. Transformers. Dr Gamal Sowilam CHAPTER Transformers Dr Gamal Sowilam Introduction A transformer is a static machine. It is not an energy conversion device, it is indispensable in many energy conversion systems. A transformer essentially

More information

Comparison of Leakage Impedances of Two Single-phase Transformers

Comparison of Leakage Impedances of Two Single-phase Transformers Aim Comparison of Leakage Impedances of Two Single-phase Transformers To understand the effect of core construction on leakage impedance in a single-phase transformers To understand factors affecting leakage

More information

3. What is hysteresis loss? Also mention a method to minimize the loss. (N-11, N-12)

3. What is hysteresis loss? Also mention a method to minimize the loss. (N-11, N-12) DHANALAKSHMI COLLEGE OF ENGINEERING, CHENNAI DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING EE 6401 ELECTRICAL MACHINES I UNIT I : MAGNETIC CIRCUITS AND MAGNETIC MATERIALS Part A (2 Marks) 1. List

More information

Design Comparison for Rectangular and Round Winding Distribution Transformer (1000kVA)

Design Comparison for Rectangular and Round Winding Distribution Transformer (1000kVA) Volume 7 ssue 10,375-380, 018, SSN:-319 7560 Comparison for Rectangular and Round Winding istribution Transformer (1000kVA) Ei Ei Chaw epartment of Electrical Power Engineering Technological University

More information

By Gill ( ) PDF created with FinePrint pdffactory trial version

By Gill (  ) PDF created with FinePrint pdffactory trial version By Gill (www.angelfire.com/al4/gill ) 1 Introduction One of the main reasons of adopting a.c. system instead of d.c. for generation, transmission and distribution of electrical power is that alternatin

More information

WELCOME TO THE LECTURE

WELCOME TO THE LECTURE WLCOM TO TH LCTUR ON TRNFORMR Single Phase Transformer Three Phase Transformer Transformer transformer is a stationary electric machine which transfers electrical energy (power) from one voltage level

More information

Spring 2000 EE361: MIDTERM EXAM 1

Spring 2000 EE361: MIDTERM EXAM 1 NAME: STUDENT NUMBER: Spring 2000 EE361: MIDTERM EXAM 1 This exam is open book and closed notes. Assume f=60 hz and use the constant µ o =4π 10-7 wherever necessary. Be sure to show all work clearly. 1.

More information

Group F : Sl. No. - 1) 33/0.403 KV, 100 KVA Station Transformer GUARANTEED & OTHER TECHNICAL PARTICULARS. Table : A

Group F : Sl. No. - 1) 33/0.403 KV, 100 KVA Station Transformer GUARANTEED & OTHER TECHNICAL PARTICULARS. Table : A Group F : No. - 1) 33/0.403 KV, 100 KVA Station Transformer GUARANTEED & OTHER TECHNICAL PARTICULARS Table : A No. Description 1. Make & Manufacturer 2. Place of Manufacturer 3. Voltage Ratio 4. Rating

More information

EEE3441 Electrical Machines Department of Electrical Engineering. Lecture. Basic Operating Principles of Transformers

EEE3441 Electrical Machines Department of Electrical Engineering. Lecture. Basic Operating Principles of Transformers Department of Electrical Engineering Lecture Basic Operating Principles of Transformers In this Lecture Basic operating principles of following transformers are introduced Single-phase Transformers Three-phase

More information

Introduction : Design detailed: DC Machines Calculation of Armature main Dimensions and flux for pole. Design of Armature Winding & Core.

Introduction : Design detailed: DC Machines Calculation of Armature main Dimensions and flux for pole. Design of Armature Winding & Core. Introduction : Design detailed: DC Machines Calculation of Armature main Dimensions and flux for pole. Design of Armature Winding & Core. Design of Shunt Field & Series Field Windings. Design detailed:

More information

Tech Byte 16: The Truths About Transformers Part 2

Tech Byte 16: The Truths About Transformers Part 2 In The Truths About Transformers Part 1, the discussion focused on the reality that not all transformers are created equal. Today, more than ever, there is a need to look at every transformer application

More information

Basics of electrical transformer

Basics of electrical transformer Visit: https://engineeringbasic.com Complete basics and theory of Electrical Transformer Electrical Transformer is the most used electrical machine in power system. Both in the power transmission and distribution

More information

Design and Analysis of Losses in Power Transformer

Design and Analysis of Losses in Power Transformer American Journal of Electrical and Electronic Engineering, 017, Vol. 5, No. 3, 94-101 Available online at http://pubs.sciepub.com/ajeee/5/3/4 Science and Education Publishing DOI:10.1691/ajeee-5-3-4 Design

More information

Transformers. gpmacademics.weebly.com

Transformers. gpmacademics.weebly.com TRANSFORMERS Syllabus: Principles of operation, Constructional Details, Losses and efficiency, Regulation of Transformer, Testing: OC & SC test. TRANSFORMER: It is a static device which transfers electric

More information

Laminate Transformer Testing

Laminate Transformer Testing 1. Introduction: Laminate transformers are mostly used as line frequency, low frequency and low/high voltage step-up, step-down transformers. Two coils are wound over a core such that they are magnetically

More information

SPECIFICATION FOR STEP UP TRANSFORMER 0.415/11Kv and (630KVA & 1000KVA)

SPECIFICATION FOR STEP UP TRANSFORMER 0.415/11Kv and (630KVA & 1000KVA) SPECIFICATION FOR STEP UP TRANSFORMER 0.415/11Kv and (630KVA & 1000KVA) 0.415/33kV DESIGN AND CONSTRUCTION General 1. The transformer shall be three phase, oil immersed type, air cooled, core type, outdoor

More information

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM I (CE,EC,EE,EN)] QUIZ TEST-3 (Session: 2012-13) Time: 1 Hour ELECTRICAL ENGINEERING Max. Marks: 30 (EEE-101) Roll No. Academic/26 Refer/WI/ACAD/18

More information

Hours / 100 Marks Seat No.

Hours / 100 Marks Seat No. 17415 15162 3 Hours / 100 Seat No. Instructions (1) All Questions are Compulsory. (2) Answer each next main Question on a new page. (3) Illustrate your answers with neat sketches wherever necessary. (4)

More information

Particulate Control O&M Training. APC/PCUG Conference July 12-16, 2009 The Woodlands, TX

Particulate Control O&M Training. APC/PCUG Conference July 12-16, 2009 The Woodlands, TX Particulate Control O&M Training APC/PCUG Conference July 12-16, 2009 The Woodlands, TX WPCA Particulate Training Seminar July 11, 2009 ESP Power Supply Choices Slide No 1 Precipitator Power Supplies Conventional

More information

Units. In the following formulae all lengths are expressed in centimeters. The inductance calculated will be in micro-henries = 10-6 henry.

Units. In the following formulae all lengths are expressed in centimeters. The inductance calculated will be in micro-henries = 10-6 henry. INDUCTANCE Units. In the following formulae all lengths are expressed in centimeters. The inductance calculated will be in micro-henries = 10-6 henry. Long straight round wire. If l is the length; d, the

More information

Copper and Electricity: Transformers and. the Grid. Transformers

Copper and Electricity: Transformers and. the Grid. Transformers PHYSICS Copper and Electricity: Transformers and 16-18 YEARS the Grid Transformers Using transformers We use transformers to change the size of a voltage. We can step the voltage down from a high voltage

More information

Electrical Design Process

Electrical Design Process Electrical Design Process Jason Varnell Lead Design Engineer Jason.Varnell@spx.com SPX Transformer Solutions, Inc. September 26, 2018 Agenda 1. Bid Design Process Parameters Affecting Bid Design 2. Final

More information

Code No: R Set No. 1

Code No: R Set No. 1 Code No: R05220204 Set No. 1 II B.Tech II Semester Supplimentary Examinations, Aug/Sep 2007 ELECTRICAL MACHINES-II (Electrical & Electronic Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions

More information

A Glance into the Future of Transformers and Beyond

A Glance into the Future of Transformers and Beyond A Glance into the Future of Transformers and Beyond Pat Bodger and Wade Enright Department of Electrical and Computer Engineering University of Canterbury, Christchurch Abstract: An overview of the research

More information

Chapter 2-1 Transformers

Chapter 2-1 Transformers Principles of Electric Machines and Power Electronics Chapter 2-1 Transformers Third Edition P. C. Sen Transformer application 1: power transmission Ideal Transformer Assumptions: 1. Negligible winding

More information

GE Ventilated Dry-Type Transformers. Secondary Substation Transformers - 5 and 15kV Class

GE Ventilated Dry-Type Transformers. Secondary Substation Transformers - 5 and 15kV Class GE Ventilated Dry-Type Transformers Secondary Substation Transformers - 5 and 15kV Class GE ventilated dry-type transformers are designed for indoor or outdoor applications in schools, hospitals, industrial

More information

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad - 00 03 ELECTRICAL AND ELECTRONICS ENGINEERING ASSIGNMENT Course Name : ELECRICAL MACHINES - II Course Code : A0 Class : II B.TECH-II

More information

DESIGN AND CONSTRUCTION OF 1500VA VARIABLE OUTPUT STEP DOWN TRANSFORMER

DESIGN AND CONSTRUCTION OF 1500VA VARIABLE OUTPUT STEP DOWN TRANSFORMER DESIGN AND CONSTRUCTION OF 1500VA VARIABLE OUTPUT STEP DOWN TRANSFORMER OGUNDARE AYOADE B., OMOGOYE O. SAMUEL & OLUWASANYA OMOTAYO J. Department of Electrical/Electronic engineering, Lagos State Polytechnic,

More information

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. 2) The model answer and the answer written by candidate

More information

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM I (EE, EN, EC, CE)] QUIZ TEST-3 (Session: ) Time: 1 Hour ELECTRICAL ENGINEE

SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM I (EE, EN, EC, CE)] QUIZ TEST-3 (Session: ) Time: 1 Hour ELECTRICAL ENGINEE SHRI RAMSWAROOP MEMORIAL COLLEGE OF ENGG. & MANAGEMENT B.Tech. [SEM I (EE, EN, EC, CE)] QUIZ TEST-3 (Session: 2014-15) Time: 1 Hour ELECTRICAL ENGINEERING Max. Marks: 30 (NEE-101) Roll No. Academic/26

More information

VIDYARTHIPLUS - ANNA UNIVERSITY ONLINE STUDENTS COMMUNITY UNIT 1 DC MACHINES PART A 1. State Faraday s law of Electro magnetic induction and Lenz law. 2. Mention the following functions in DC Machine (i)

More information

Basic Principles and Operation of Transformer

Basic Principles and Operation of Transformer Basic Principles and Operation of Transformer CONSTRUCTIONAL ASPECTS Cores In order to enhance core s magnetic properties, it is constructed from an iron and silicon mixture (alloy). The magnetic core

More information

A modified area product method for the design of inductors and transformers

A modified area product method for the design of inductors and transformers J. Indian Inst. Sci., Sept. Oct. 2000, 80, 429-435. Indian Institute of Science A modified area product method for the design of inductors and transformers G. S. RAMANA MURTHY* AND V. RAMANARAYANAN** Department

More information

Power Transformers Basics

Power Transformers Basics Power Transformers Basics Transformer Basic Objective Introduce Basic Transformer Theory as it Relates to Diagnostics Provide a Better Understanding of the Diagnostic Test Environment Identify Important

More information

TRANSFORMER TECHNOLOGY GPT

TRANSFORMER TECHNOLOGY GPT Core-Form TRANSFORMER TECHNOLOGY GlobalPT Corporation performs research and engineering developments and co-ordination of works of technical partners in the field of technological progress and commercial

More information

Single & Three Phase Transformers SAMPLE. Learner Workbook. Version 1. Training and Education Support Industry Skills Unit Meadowbank

Single & Three Phase Transformers SAMPLE. Learner Workbook. Version 1. Training and Education Support Industry Skills Unit Meadowbank Single & Three Phase Transformers Learner Workbook Version 1 Training and Education Support Industry Skills Unit Meadowbank Product Code: 5634 Table of Contents Introduction... 5 Section 1. Transformer

More information

HTS PARTIAL CORE TRANSFORMER- FAULT CURRENT LIMITER

HTS PARTIAL CORE TRANSFORMER- FAULT CURRENT LIMITER EEA CONFERENCE & EXHIBITION 2013, 19-21 JUNE, AUCKLAND HTS PARTIAL CORE TRANSFORMER- FAULT CURRENT LIMITER JIT KUMAR SHAM*, UNIVERSITY OF CANTERBURY, CHRISTCHURCH, NEW ZEALAND PROF. PAT BODGER, UNIVERSITY

More information

ELECTRICAL MEASUREMENTS

ELECTRICAL MEASUREMENTS R10 Set No: 1 1. a) Derive the expression for torque equation for a moving iron attraction type instrument and comment up on the nature of scale [8] b) Define the terms current sensitivity, voltage sensitivity

More information

Electrical Machines I : Transformers

Electrical Machines I : Transformers UNIT TRANSFORMERS PART A (Q&A) 1. What is step down transformer? The transformer used to step down the voltage from primary to secondary is called as step down transformer. (Ex: /11).. Draw the noload

More information

Power Transformers. Energy Systems Research Laboratory, FIU

Power Transformers. Energy Systems Research Laboratory, FIU Power Transformers By: Alberto Berzoy Energy Systems Research Laboratory Department of Electrical & Computer Engineering Florida International University Miami, Florida, USA Overview 2 Introduction Transformer

More information

148 Electric Machines

148 Electric Machines 148 Electric Machines 3.1 The emf per turn for a single-phase 2200/220- V, 50-Hz transformer is approximately 12 V. Calculate (a) the number of primary and secondary turns, and (b) the net cross-sectional

More information

MGM Transformer. Vacuum Pressure Impregnated (VPI) Dry-Type Substation Transformer Specification Guide

MGM Transformer. Vacuum Pressure Impregnated (VPI) Dry-Type Substation Transformer Specification Guide MGM Transformer Vacuum Pressure Impregnated (VPI) Dry-Type Substation Transformer Specification Guide MGM Transformer Company 5701 Smithway Street Commerce, CA 90040 www.mgmtransformer.com Phone: 323.726.0888

More information

Designing Your Own Transformer written by: Swagatam edited by: Lamar Stonecypher updated: 11/1/2011

Designing Your Own Transformer written by: Swagatam edited by: Lamar Stonecypher updated: 11/1/2011 Designing Your Own Transformer written by: Swagatam edited by: Lamar Stonecypher updated: 11/1/2011 Designing a transformer is not easy simply because the criteria involved with these devices are critical

More information

FERRORESONANT PROGRAM MANUAL V12.0

FERRORESONANT PROGRAM MANUAL V12.0 FERRO OPTIMIZED PROGRAM SERVICE, LLC Electro-Magnetic Design Using Advanced Computer Techniques FERRORESONANT PROGRAM MANUAL V12.0 www.opsprograms.com opseast@opsprograms.com FERRO PROGRAM DESCRIPTION

More information

Code No: R Set No. 1

Code No: R Set No. 1 Code No: R05310204 Set No. 1 III B.Tech I Semester Regular Examinations, November 2007 ELECTRICAL MACHINES-III (Electrical & Electronic Engineering) Time: 3 hours Max Marks: 80 Answer any FIVE Questions

More information

Transformer Winding Design. The Design and Performance of Circular Disc, Helical and Layer Windings for Power Transformer Applications

Transformer Winding Design. The Design and Performance of Circular Disc, Helical and Layer Windings for Power Transformer Applications The Design and Performance of Circular Disc, Helical and Layer Windings for Power Transformer Applications Minnesota Power Systems Conference November 3 5, 2009 Earl Brown Heritage Center University of

More information

1249. Development of large salient-pole synchronous machines by using fractional-slot concentrated windings

1249. Development of large salient-pole synchronous machines by using fractional-slot concentrated windings 1249. Development of large salient-pole synchronous machines by using fractional-slot concentrated windings Tayfun Gundogdu 1, Guven Komurgoz 2 Istanbul Technical University, Department of Electrical Engineering,

More information

1 K Hinds 2012 TRANSFORMERS

1 K Hinds 2012 TRANSFORMERS 1 K Hinds 2012 TRANSFORMERS A transformer changes electrical energy of a given voltage into electrical energy at a different voltage level. It consists of two coils which are not electrically connected,

More information

Induction heating of internal

Induction heating of internal OPTIMAL DESIGN OF INTERNAL INDUCTION COILS The induction heating of internal surfaces is more complicated than heating external ones. The three main types of internal induction coils each has its advantages

More information

Liquid-Filled Transformers

Liquid-Filled Transformers Liquid-Filled Transformers Custom Transformers at Standard Prices NIAGARA TRANSFORMER CORP. Induction Furnace Transformer Cycloconverter Rectifier Duty Transformer Arc Furnace Transformer Full Range of

More information

LEAKAGE FLUX CONSIDERATIONS ON KOOL Mµ E CORES

LEAKAGE FLUX CONSIDERATIONS ON KOOL Mµ E CORES LEAKAGE FLUX CONSIDERATIONS ON E CORES Michael W. Horgan Senior Applications Engineer Magnetics Division of Spang & Co. Butler, PA 163 Abstract Kool Mu, a Silicon-Aluminum-Iron powder, is a popular soft

More information

Lecture 16 Transformer Design

Lecture 16 Transformer Design Design and Simulation of DC-DC converters using open source tools Prof. L. Umanand Department of Electronics System Engineering Indian Institute of Science, Bangalore Lecture 16 Transformer Design In this

More information

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. 2) The model answer and the answer written by candidate

More information

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad - 00 0 ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK Course Name Course Code Class Branch : ELECRICAL MACHINES - II : A0 :

More information

PERFORMANCE OF SIX PHASE INDUCTION MOTOR USING SPECIAL TRANSFORMER CONNECTION

PERFORMANCE OF SIX PHASE INDUCTION MOTOR USING SPECIAL TRANSFORMER CONNECTION PERFORMANCE OF SIX PHASE INDUCTION MOTOR USING SPECIAL TRANSFORMER CONNECTION Aravind Bhandare 1, Mahesh Bhosale 2, Kiran Chikodikar 3, Pankaj Kamble 4, Rohit Mali 5 Assistant Professor, Electrical Engineering

More information

Effects of Harmonic Distortion I

Effects of Harmonic Distortion I Effects of Harmonic Distortion I Harmonic currents produced by nonlinear loads are injected back into the supply systems. These currents can interact adversely with a wide range of power system equipment,

More information

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad ELECTRICAL AND ELECTRONICS ENGINEERING

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad ELECTRICAL AND ELECTRONICS ENGINEERING Course Name Course Code Class Branch INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad - 500 043 ELECTRICAL AND ELECTRONICS ENGINEERING QUESTION BANK : ELECRICAL MACHINES I : A40212

More information

Line Frequency Transformer

Line Frequency Transformer Line Frequency Transformer For frequencies of 50/60 Hz, specify a Frequency Transformer. Line Line Frequency Transformers are customized to meet customer requirements, and are available in various ratings.

More information

SOUTHERN ELECTRICITY SUPPLY COMPANY OF ODISHA LIMITED (SOUTHCO UTILITY)

SOUTHERN ELECTRICITY SUPPLY COMPANY OF ODISHA LIMITED (SOUTHCO UTILITY) E -Tender Notice No. Annexure - VII SOUTHCO/DEPOSIT/3.15 & 5 MVA Power Transformer /02/2015 16 Dt. 02.03.2016 NAME OF THE WORK PROCUREMENT OF33/11 KV, 3.15 MVA & 5 MVA Power Transformer SUPPLIER INFORMATION

More information

Module 7. Transformer. Version 2 EE IIT, Kharagpur

Module 7. Transformer. Version 2 EE IIT, Kharagpur Module 7 Transformer Lesson 28 Problem solving on Transformers Contents 28 Problem solving on Transformer (Lesson-28) 4 28.1 Introduction. 4 28.2 Problems on 2 winding single phase transformers. 4 28.3

More information

DESIGN OF TRANSFORMER PERIPHARALS BY COMPUTER AIDED DESIGN DRAFTING (CADD)

DESIGN OF TRANSFORMER PERIPHARALS BY COMPUTER AIDED DESIGN DRAFTING (CADD) IAETSD JOURNAL FOR ADVANCED RESEARCH IN APPLIED SCIENCES, VOLUME 4, ISSUE 4, SEPT /2017 ISSN (ONLINE): 2394-8442 DESIGN OF TRANSFORMER PERIPHARALS BY COMPUTER AIDED DESIGN DRAFTING (CADD) B. Phani Ranga

More information

LOSS ESTIMATION FOR THREE 33/11kV TRANSFORMERS AT SCOTTISH & SOUTHERN ENERGY POWER DISTRIBUTION

LOSS ESTIMATION FOR THREE 33/11kV TRANSFORMERS AT SCOTTISH & SOUTHERN ENERGY POWER DISTRIBUTION LOSS ESTIMATION FOR THREE 33/11kV TRANSFORMERS AT SCOTTISH & SOUTHERN ENERGY POWER DISTRIBUTION by SIMON RYDER Addressee: MACIEJ FILA (SCOTTISH& SOUTHERN ENERGY POWER DISTRIBUTION) Registered in England

More information

Module 7. Transformer. Version 2 EE IIT, Kharagpur

Module 7. Transformer. Version 2 EE IIT, Kharagpur Module 7 Transformer Lesson 3 Ideal Transformer Contents 3 Ideal Transformer (Lesson: 3) 4 3. Goals of the lesson 4 3. Introduction.. 5 3.. Principle of operation.. 5 3.3 Ideal Transformer.. 6 3.3. Core

More information

VALLIAMMAI ENGINEERING COLLEGE

VALLIAMMAI ENGINEERING COLLEGE VALLIAMMAI ENGINEERING COLLEGE SRM Nagar, Kattankulathur 603 203 DEPARTMENT OF ELECTRONICS AND INSTRUMENTATION ENGINEERING QUESTION BANK IV SEMESTER EI6402 ELECTRICAL MACHINES Regulation 2013 Academic

More information

Title Substation Auxiliary Transformer from Rectifier Transformer Secondary. Reference Number PDS 01 (RIC Standard: EP SP)

Title Substation Auxiliary Transformer from Rectifier Transformer Secondary. Reference Number PDS 01 (RIC Standard: EP SP) Discipline Engineering Standard NSW Category Electrical Title Substation Auxiliary Transformer from Rectifier Transformer Secondary Reference Number PDS 01 (RIC Standard: EP 05 00 00 01 SP) Document Control

More information

TUTORIAL Inductor Database in the Thermal Module

TUTORIAL Inductor Database in the Thermal Module TUTORIAL Inductor Database in the Thermal Module October 2016 1 A typical inductor consists of three main parts: core, bobbin (also called coil former), and winding, as shown below. To construct an inductor

More information

Prolific Systems & Technologies Pvt. Ltd. CORE DETAILS. CENTRE Figure - II L-2 X Y Wt-2

Prolific Systems & Technologies Pvt. Ltd. CORE DETAILS. CENTRE Figure - II L-2 X Y Wt-2 Plot No. A-267, MIDC, Road No. 6A, Opp. ESIS Hospital, Wagle Industrial Estate, Thane (West) - 400 604 CORE DETAILS Date: 4/2/206 Design No. mahati Step No. SIDES Figure - I B L- Wt- CENTRE Figure - II

More information

Regional Technical Seminar SHORT CIRCUIT FORCES

Regional Technical Seminar SHORT CIRCUIT FORCES Regional Technical Seminar SHORT CIRCUIT FORCES Short Circuit Forces Wallace Exum Electrical Design Engineer wallace.exum@spx.com Agenda 1. What is Short Circuit 2. Types of Faults 3. How to Calculate

More information

ELECTRICAL MACHINES - II COURSEFILE

ELECTRICAL MACHINES - II COURSEFILE ELECTRICAL MACHINES - II COURSEFILE Coursefile contents: 1. Cover Page 2. Syllabus copy 3. Vision of the department 4. Mission of the department 5. PEOs and POs 6. Course objectives and outcomes 7. Brief

More information

International Journal of Advance Engineering and Research Development

International Journal of Advance Engineering and Research Development Scientific Journal of Impact Factor (SJIF): 4.72 International Journal of Advance Engineering and Research Development Volume 4, Issue 1, January -2017 e-issn (O): 2348-4470 p-issn (P): 2348-6406 Design

More information

Large Kool Mµ Core Shapes

Large Kool Mµ Core Shapes Large Kool Mµ Core Shapes TECHNICAL BULLETIN Ideal for high current inductors, large Kool Mµ geometries (E cores, U Cores and Blocks) offer all the advantages of Kool Mµ material, low core loss, excellent

More information

COMPANY PROFILE... 1 QUALITY CERTIFICATES... 2 APPLICATIONS... 3

COMPANY PROFILE... 1 QUALITY CERTIFICATES... 2 APPLICATIONS... 3 CONTENTS COMPANY PROFILE... 1 QUALITY CERTIFICATES... 2 APPLICATIONS... 3 CONSTRUCTION... 4 ~ 5 A. CORE AND FRAME... 4 B. COIL... 5 C. TEMPERATURE INDICATOR... 5 CHARACTERISTICS... 6 MANUFACTURING FACILITIES...

More information

Keywords: Overvoltage Suppression, Shunt Reactor, Loss Reduction, Regulate Voltage Level, Reactive Power Balance.

Keywords: Overvoltage Suppression, Shunt Reactor, Loss Reduction, Regulate Voltage Level, Reactive Power Balance. www.semargroup.org, www.ijsetr.com ISSN 2319-8885 Vol.03,Issue.11 June-2014, Pages:2481-2486 Design of 25 MVA Shunt Reactor for 230 kv Transmission Line HSU MON AUNG 1, DR. MIN MIN OO 2 1 Dept of Electrical

More information

Shunt Reactors. Global Top Energy, Machinery & Plant Solution Provider

Shunt Reactors. Global Top Energy, Machinery & Plant Solution Provider Shunt Reactors Global Top Energy, Machinery & Plant Solution Provider Our Business Brief introduction of Hyosung Power & Industrial Systems PG While Hyosung is an established name for world-class electrical

More information

PART A. 1. List the types of DC Motors. Give any difference between them. BTL 1 Remembering

PART A. 1. List the types of DC Motors. Give any difference between them. BTL 1 Remembering UNIT I DC MACHINES Three phase circuits, a review. Construction of DC machines Theory of operation of DC generators Characteristics of DC generators Operating principle of DC motors Types of DC motors

More information

Large Kool Mµ Core Shapes

Large Kool Mµ Core Shapes Large Kool Mµ Core Shapes TECHNICAL BULLETIN Ideal for high current inductors, large Kool Mµ geometries (E cores, U Cores and Blocks) offer all the advantages of Kool Mµ material, low core loss, excellent

More information

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad -00 03 ELECTRCIAL AND ELECTRONICS ENGINEERING TUTORIAL QUESTION BANK Course Name Course Code Class Branch : DC MACHINES AND TRANSFORMERS

More information

AEIJST - January Vol 5 - Issue 01 ISSN Minimization Iron Losses in Transformer

AEIJST - January Vol 5 - Issue 01 ISSN Minimization Iron Losses in Transformer Abstract Minimization Iron Losses in Transformer *P.Ramesh *MIE, MISTE It is almost impossible to reduce the iron losses completely; however these can be reduced to a certain extent. Here we have made

More information

TRAFTOR WINDINGS CHANGING THE RULES TOROIDAL INDUCTORS & TRANSFORMERS SOLUTIONS PROVIDER AND MANUFACTURER

TRAFTOR WINDINGS CHANGING THE RULES TOROIDAL INDUCTORS & TRANSFORMERS SOLUTIONS PROVIDER AND MANUFACTURER TRAFTOR WINDINGS CHANGING THE RULES TOROIDAL INDUCTORS & TRANSFORMERS SOLUTIONS PROVIDER AND MANUFACTURER PRODUCT RANGE POWER INDUCTORS Toroidal technology, driven by 20 years of R&D. POWER TRANSFORMERS

More information

Generator Advanced Concepts

Generator Advanced Concepts Generator Advanced Concepts Common Topics, The Practical Side Machine Output Voltage Equation Pitch Harmonics Circulating Currents when Paralleling Reactances and Time Constants Three Generator Curves

More information

The Study of Magnetic Flux Shunts Effects on the Leakage Reactance of Transformers via FEM

The Study of Magnetic Flux Shunts Effects on the Leakage Reactance of Transformers via FEM Majlesi Journal of Electrical Engineering Vol. 4, 3, September 00 The Study of Magnetic Flux Shunts Effects on the Leakage Reactance of Transformers via FEM S. Jamali Arand, K. Abbaszadeh - Islamic Azad

More information

THE UNIVERSITY OF BRITISH COLUMBIA. Department of Electrical and Computer Engineering. EECE 365: Applied Electronics and Electromechanics

THE UNIVERSITY OF BRITISH COLUMBIA. Department of Electrical and Computer Engineering. EECE 365: Applied Electronics and Electromechanics THE UNIVERSITY OF BRITISH COLUMBIA Department of Electrical and Computer Engineering EECE 365: Applied Electronics and Electromechanics Final Exam / Sample-Practice Exam Spring 2008 April 23 Topics Covered:

More information

Engineering Science OUTCOME 4 - TUTORIAL 3 CONTENTS. 1. Transformers

Engineering Science OUTCOME 4 - TUTORIAL 3 CONTENTS. 1. Transformers Unit : Unit code: QCF Level: 4 Credit value: 5 SYLLABUS Engineering Science L/60/404 OUTCOME 4 - TUTOIAL 3 Be able to apply single phase AC theory to solve electrical and electronic engineering problems

More information

AUTO-TRANSFORMER. This is having only one winding; part of this winding is common to both primary and secondary.

AUTO-TRANSFORMER. This is having only one winding; part of this winding is common to both primary and secondary. AUTO-TRANSFORMER This is having only one winding; part of this winding is common to both primary and secondary. In 2-winding transformer both primary and secondary windings are electrically isolated, but

More information

THE APPLICATION OF POLE MOUNTED AMORPHOUS CORE TRANSFORMERS TO THE ELECTRICAL DISTRIBUTION NETWORK

THE APPLICATION OF POLE MOUNTED AMORPHOUS CORE TRANSFORMERS TO THE ELECTRICAL DISTRIBUTION NETWORK THE APPLICATION OF POLE MOUNTED AMORPHOUS CORE TRANSFORMERS TO THE ELECTRICAL DISTRIBUTION NETWORK Jasoda Naidoo In fulfilment of the Masters of Science, College of Agriculture, Engineering and Science,

More information

Transformers. ELG3311: Habash,

Transformers. ELG3311: Habash, Transformers A transformer is a device that changes AC electric power at one voltage level to AC electric power at another voltage level through the action of magnetic field. t consists of two or more

More information

~=E.i!=h. Pre-certification Transformers

~=E.i!=h. Pre-certification Transformers 7 Transformers Section 26 of the electrical code governs the use and installations of transformers. A transformer is a static device used to transfer energy from one alternating current circuit to another.

More information

Three Winding Transformer.

Three Winding Transformer. Three Winding Transformer. By G. K. KAISER (Transformer Engineer, Mitsubishi Denki-Kabushikikaisha.) Abstract. Three winding transformers afford many advantages on large power systems and their use has

More information

R. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder

R. W. Erickson. Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder R. W. Erickson Department of Electrical, Computer, and Energy Engineering University of Colorado, Boulder 13.2.3 Leakage inductances + v 1 (t) i 1 (t) Φ l1 Φ M Φ l2 i 2 (t) + v 2 (t) Φ l1 Φ l2 i 1 (t)

More information

Large Kool Mµ Core Shapes

Large Kool Mµ Core Shapes Large Kool Mµ Core Shapes Technical Bulletin Ideal for high current inductors, large Kool Mµ geometries (E cores, Toroids, U Cores and Blocks) offer all the advantages of Kool Mµ material, low core loss,

More information

Magnetic Path Length. Outside Dimensions Outer Diameter mm

Magnetic Path Length. Outside Dimensions Outer Diameter mm MAJOR USES Output choke coils for Switching Mode Power Supply For DC-DC converter Normal mode choke coils for noise control Please contact us when the coils are used in a high-voltage circuit. FEATURES

More information