TC620/TC621. 5V, Dual Trip Point Temperature Sensors. Features. Package Type. Applications. Device Selection Table. General Description

Transcription

1 V, Dual Trip Point Temperature Sensors Features User Programmable Hysteresis and Temperature Set Point Easily Programs with External Resistors Wide Temperature Detection Range: -0 C to 0 C: (TC0/TCCCX) -0 C to + C: (TC0/TCCVX) -0 C to + C: (TC0/TCCEX) - C to + C: (TC0/TCCMX) Onboard Temperature Sensing Applications (TC0X) External NTC Thermistor for Remote Sensing Applications (TCX) Availablein-PinPDIPandSOICPackages Applications Power Supply Over Temperature Detection Consumer Equipment Temperature Regulators CPU Thermal Protection Device Selection Table Part Number Package Temperature Range TC0X*COA -Pin SOIC 0 C to +0 C TC0X*CPA -Pin PDIP 0 C to +0 C TC0X*EOA -Pin SOIC -0 C to + C TC0X*EPA -Pin PDIP -0 C to + C TC0C*VOA -Pin SOIC -0 C to + C TCX*COA -Pin SOIC 0 C to +0 C TCX*CPA -Pin PDIP 0 C to +0 C TCX*EOA -Pin SOIC -0 C to + C TCX*EPA -Pin PDIP -0 C to + C NOTE: *The part code will be C or H. (See Functional Block Diagrams). Package Type NC LOW SET HIGH SET GND THERMISTOR HIGH SET LOW SET GND NC LOW SET HIGH SET GND THERMISTOR HIGH SET LOW SET GND General Description -PDIP TC0XCPA TC0XEPA -PDIP TCXCPA TCXEPA -SOIC TC0XCOA TC0XEOA TC0CVOA -SOIC TCXCOA TCXEOA VDD LOW LIMIT HIGH LIMIT CONTROL VDD HIGH LIMIT LOW LIMIT CONTROL The TC0 and TC are programmable logic output temperature detectors designed for use in thermal management applications. The TC0 features an onboard temperature sensor, while the TC connects to an external NTC thermistor for remote sensing applications. Both devices feature dual thermal interrupt outputs (HIGH LIMIT and LOW LIMIT), each of which is programmed with a single external resistor. On the TC0, these outputs are driven active (high) when measured temperature equals the user programmed limits. The CONTROL (hysteresis) output is driven high when temperature equals the high limit setting and returns low when temperature falls below the low limit setting. This output can be used to provide ON/OFF control to a cooling fan or heater. The TC provides the same output functions except that the logical states are inverted. The TC0/TC are usable over operating temperature ranges of 0 C to 0 C, -0 C to + C and - C to C. VDD HIGH LIMIT LOW LIMIT CONTROL VDD HIGH LIMIT LOW LIMIT CONTROL 00 Microchip Technology Inc. DS9B-page

2 Functional Block Diagrams V DD Temp. to Voltage Converter TC0 LOW SET V REF GEN + LOW LIMIT V REF HIGH SET V REF GEN + R S HIGH LIMIT Q Q CONTROL* V DD THERMISTOR Thermistor Interface Circuit TC HIGH SET V REF GEN + HIGH LIMIT V REF LOW SET V REF GEN + LOW LIMIT R S Q Q CONTROL* *Suffix code "C" denotes cooling option (High true CONTROL output). Suffix code "H" denotes heating option (Low true CONTROL output). DS9B-page 00 Microchip Technology Inc.

3 .0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings* Supply Voltage... 0V Input Voltage Any Input.. (GND 0.V) to (V DD +0.V) Package Power Dissipation (T A 0 C) PDIP...0mW SOIC...0mW Derating Factors: Plastic... mw/ C Operating Temperature: M Version... - C to + C V Version C to + C E Version C to + C C Version... 0 C to +0 C Storage Temperature... - C to +0 C *Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. TC0/TC ELECTRICAL SPECIFICATIONS Electrical Characteristics: T A = C, unless otherwise specified. Symbol Parameter Min Typ Max Unit Test Conditions V DD Supply Voltage Range. V I DD Supply Current 0 00 µa V V DD V R OUT Output Resistance W Output High or Low, V V DD V I OUT Output Current ma Temp Sensed Source/Sink I OUT Output Current ma Cool/Heat Source/Sink T ERR Absolute Accuracy T - T T + C T = Programmed Temperature 00 Microchip Technology Inc. DS9B-page

4 .0 PIN DESCRIPTIONS ThedescriptionsofthepinsarelistedinTable-. TABLE -: PIN FUNCTION TABLE Pin No. (-Pin PDIP) (-Pin SOIC) 0 C to +0 C -0 C to + C -0 C to + C Symbol NC No Internal Connection. Description LOW SET Low temperature set point. Connect an external % resistor from LOW SET to V DD to set trip point. HIGH SET High temperature set point. Connect an external % resistor from HIGH SET to V DD to set trip point. GND Ground Terminal. CONTROL Control output. HIGH LIMIT High temperature push/pull output. LOW LIMIT Low temperature push/pull output. V DD Power supply input. Pin No. (-Pin PDIP) (-Pin SOIC) 0 C to +0 C -0 C to + C Symbol Description THERMISTOR Thermistor input. HIGH SET High temperature set point. Connect an external % resistor from HIGH SET to V DD to set trip point. LOW SET Low temperature set point. Connect an external % resistor from LOW SET to V DD to set trip point. GND Ground Terminal. CONTROL Control output. LOW LIMIT Low temperature push/pull output. HIGH LIMIT High temperature push/pull output. V DD Power supply input. DS9B-page 00 Microchip Technology Inc.

5 .0 DETAILED DESCRIPTION The TC0 has a positive temperature coefficient temperature sensor and a dual threshold detector. Temperature set point programming is accomplished with external resistors from the HIGH SET and LOW SET inputs to V DD. The HIGH LIMIT and LOW LIMIT outputs remain low as long as measured temperature is below set point values. As measured temperature increases, the LOW LIMIT output is driven high when temperature equals the LOW SET set point (± C max). If temperature continues to climb, the HIGH LIMIT output is driven high when temperature equals the HIGH SET set point (Figure -). The CONTROL (hysteresis) output is latched in its active state at the temperature specified by the HIGH SET resistor. CONTROL is maintained active until temperature falls to the value specified by the LOW SET resistor. FIGURE -: High Set Point Low Set Point Low Limit Output High Limit Output Control Output (Cool Option Control Output (Heat Option) TC0/TC INPUT VS. OUTPUT LOGIC Temperature Care must also be taken to ensure the LOW SET temperature setting is at least C lower than the HIGH SET temperature setting. Figure - can help the user obtain an estimate of the external resistor values required for the desired LOW SET and HIGH SET trip points. FIGURE -: RESISTANCE, R TRIP (kω) Built-in Hysteresis TC0 SENSE RESISTORS VS. TRIP TEMPERATURE TEMPERATURE ( C) To prevent output "chattering" when measured temperature is at (or near) the programmed trip point values, the LOW SET and HIGH SET inputs each have built-in hysteresis of - C below the programmed settings (Figure -).. Programming the TC0 The resistor values to achieve the desired trip point temperatures on HIGH SET and LOW SET are calculated using Equation -: EQUATION -: R TRIP = 0.99 x T. Where: R TRIP = Programming resistor in Ohms T = The desired trip point temperature in degrees Kelvin. FIGURE -: Set Point (Set Point C) High Limit or Low Limit Output BUILT-IN HYSTERESIS ON LOW LIMIT AND HIGH LIMIT OUTPUTS For example, a 0 C setting on either the HIGH SET or LOW SET input is calculated using Equation - as follows: EQUATION -: As shown, the outputs remain in their active state (hysteresis) until temperature falls an additional C below the user's setting. R SET = 0.99 x ((0 +.). ) =.kω Care must be taken to ensure the LOW SET programming resistor is a smaller value than the HIGH SET programming resistor. Failure to do this will result in erroneous operation of the CONTROL output. 00 Microchip Technology Inc. DS9B-page

6 . Using the TC The TC operation is similar to that of the TC0, but requires an external NTC thermistor. Use the resistance versus temperature curve of the thermistor to determine the values of the programming resistors. Note that the pin numbers for the HIGH SET and LOW SET programming resistors for the TC are reversed versus that of the TC0 (i.e., the resistor value on HIGH SET [Pin ] should always be lower than the one connected to LOW SET [Pin ]). Also note that the outputs of the TC are LOW TRUE when used with an NTC thermistor.. TC Thermistor Selection The TC uses an external thermistor to monitor the controlling temperature. A thermistor with a resistance value of approximately 00kΩ at C is recommended. A temperature set point is selected by picking a resistor whose value is equal to the resistance of the thermistor at the desired temperature. For example, using thedatashowninfigure-,a0kω resistor between HIGH TEMP (Pin ) and V DD (Pin ) sets the high temperature trip point at + C and a 9kΩ resistor on LOW TEMP (Pin ) sets the low temperature trip point to + C. FIGURE -: THERMISTOR RESISTANCE (kω) TYPICAL NTC THERMISTOR TEMPERATURE ( C). TC0/TC Outputs Both devices have complimentary output stages. They are rated at a source or sink current of ma maximum. 0 0 DS9B-page 00 Microchip Technology Inc.

7 .0 TYPICAL APPLICATIONS. Dual Speed Temperature Control In Figure -, the Dual Speed Temperature Control uses a TC0 and a TC9 quad driver. Two of the drivers of the TC9 are configured in a simple oscillator. When the temperature is below the LOW TEMP set point, the output of the driver is OFF. When the temperature exceeds the LOW TEMP set point, the TC9 gates the oscillator signal to the outputs of the driver. This square wave signal modulates the remaining outputs and drives the motor at a low speed. If this speed cannot keep the temperature below the HIGH TEMP set point, then the driver turns on continuously which increases the fan speed to high. The TC0 will monitor the temperature and only allow the fan to operate when needed and at the required speed to maintain the desired temperature. A higher power option can be designed by adding a resistor and a power MOSFET.. Temperature Controlled Fan In the application in Figure -, a high and a low temperature is selected by two R L and R H. The TC0 monitors the ambient temperature and turns the FET switch on when the temperature exceeds the HIGH TEMP set point. The fan remains on until the temperature decreases to the LOW TEMP set point. This provides the hysteresis. In this application, the fan turns on only when required. The TC uses an external thermistor to monitor the ambient temperature. This adds one part, but allows more flexibility with the location of the temperature sensor. FIGURE -: DUAL SPEED TEMPERATURE CONTROL +V V MOTOR Low Temp 0 C High Temp. 0 C Temperature Scale 0 C 0 C (Fan Off) 0 C 0 C (Fan Low) 0 C UP (Fan High) High Limit TC0 Low Limit 0.µF 0µF N N µf 0k TC9 9 0 M 00k 0pF Fan Motor 0Ω MOSFET Higher Power Option Fan Motor FIGURE -: TEMPERATURE CONTROLLED FAN +V +V Low Temp. R L R H High Temp. TC0 Fan Motor MTP0E High Temp. R H Low Temp. R L Thermistor (NTC) TC Fan Motor MTP0E 00 Microchip Technology Inc. DS9B-page

8 FIGURE -: HEATING AND COOLING APPLICATION.V to V High Temp. Low Temp. TC0 TC9 0 9 k k High Temp. Warning Low Temp. Warning Heating/Cooling Equipment DS9B-page 00 Microchip Technology Inc.

9 .0 PACKAGING INFORMATION. Package Marking Information Package marking data not available at this time.. Taping Form Component Taping Orientation for -Pin SOIC (Narrow) Devices PIN User Direction of Feed W Standard Reel Component Orientation for TR Suffix Device Carrier Tape, Number of Components Per Reel and Reel Size P Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size -Pin SOIC (N) mm mm 00 in. Package Dimensions -Pin Plastic DIP PIN.0 (.0).0 (.0).0 (.).00 (0.).00 (0.). (.).00 (.).00 (.0).0 (.).90 (.).00 (.0).0 (.).0 (.). (.9).00 (.0).00 (0.).0 (0.).00 (0.0) MIN..0 (.9).090 (.9).0 (0.).0 (0.).00 (0.).0 (.) Dimensions: inches (mm) 00 Microchip Technology Inc. DS9B-page 9

10 Package Dimensions (Continued) -Pin SOIC PIN. (.99).0 (.). (.0). (.9).00 (.) TYP..9 (.00).9 (.0).00 (0.).0 (0.).00 (0.).00 (0.0).09 (.).0 (.) MAX..00 (0.).00 (0.).00 (.).0 (0.0) Dimensions: inches (mm) DS9B-page 0 00 Microchip Technology Inc.

11 SALES AND SUPPORT Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following:. Your local Microchip sales office. The Microchip Corporate Literature Center U.S. FAX: (0) 9-. The Microchip Worldwide Site ( Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site ( to receive the most current information on our products. 00 Microchip Technology Inc. DS9B-page

12 NOTES: DS9B-page 00 Microchip Technology Inc.

13 Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, FilterLab, KEELOQ, microid, MPLAB, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. dspic, ECONOMONITOR, FanSense, FlexROM, fuzzylab, In-Circuit Serial Programming, ICSP, ICEPIC, microport, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, MXDEV, PICC, PICDEM, PICDEM.net, rfpic, Select Mode and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. 00, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 999 and Mountain View, California in March 00. The Company s quality system processes and procedures are QS-9000 compliant for its PICmicro -bit MCUs, KEELOQ code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchip s quality system for the design and manufacture of development systems is ISO 900 certified. 00 Microchip Technology Inc. DS9B-page

14 WORLDWIDE SALES AND SERVICE AMERICAS Corporate Office West Chandler Blvd. Chandler, AZ -99 Tel: Fax: 0-9- Technical Support: 0-9- Web Address: Rocky Mountain West Chandler Blvd. Chandler, AZ -99 Tel: Fax: 0-9- Atlanta 00 Sugar Mill Road, Suite 00B Atlanta, GA 00 Tel: Fax: Boston Lan Drive, Suite 0 Westford, MA 0 Tel: 9-9- Fax: 9-9- Chicago Pierce Road, Suite 0 Itasca, IL 0 Tel: Fax: Dallas 0 Westgrove Drive, Suite 0 Addison, TX 00 Tel: 9-- Fax: 9--9 Detroit Tri-Atria Office Building Northwestern Highway, Suite 90 Farmington Hills, MI Tel: --0 Fax: --0 Kokomo S. Albright Road Kokomo, Indiana 90 Tel: --0 Fax: -- Los Angeles 0 Von Karman, Suite 090 Irvine, CA 9 Tel: 99-- Fax: 99-- New York 0 Motor Parkway, Suite 0 Hauppauge, NY Tel: --0 Fax: -- San Jose Microchip Technology Inc. 0 North First Street, Suite 90 San Jose, CA 9 Tel: Fax: 0--9 Toronto Northam Drive, Suite 0 Mississauga, Ontario LV X, Canada Tel: Fax: ASIA/PACIFIC Australia Microchip Technology Australia Pty Ltd Suite, Rawson Street Epping, NSW Australia Tel: --9- Fax: --9- China - Beijing Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 9 Bei Hai Wan Tai Bldg. No. Chaoyangmen Beidajie Beijing, 000, No. China Tel: Fax: -0-0 China - Chengdu Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 0, th Floor, Ming Xing Financial Tower No. TIDU Street Chengdu 00, China Tel: --00 Fax: --99 China - Fuzhou Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Unit F, World Trade Plaza No. Wusi Road Fuzhou 000, China Tel: Fax: -9-0 China - Shanghai Microchip Technology Consulting (Shanghai) Co., Ltd. Room 0, Bldg. B Far East International Plaza No. Xian Xia Road Shanghai, 000 Tel: Fax: China - Shenzhen Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm., /F, Shenzhen Kerry Centre, Renminnan Lu Shenzhen 00, China Tel: --0 Fax: --0 Hong Kong Microchip Technology Hongkong Ltd. Unit 90-, Tower, Metroplaza Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: Fax: -0- India Microchip Technology Inc. India Liaison Office Divyasree Chambers Floor, Wing A (A/A) No., O Shaugnessey Road Bangalore, 0 0, India Tel: Fax: Japan Microchip Technology Japan K.K. Benex S- F --0, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, -00, Japan Tel: --- Fax: --- Korea Microchip Technology Korea -, Youngbo Bldg. Floor Samsung-Dong, Kangnam-Ku Seoul, Korea - Tel: Fax: ---9 Singapore Microchip Technology Singapore Pte Ltd. 00 Middle Road #0-0 Prime Centre Singapore, 90 Tel: --0 Fax: --0 Taiwan Microchip Technology Taiwan F-, No. 0 Tung Hua North Road Taipei, 0, Taiwan Tel: --- Fax: EUROPE Denmark Microchip Technology Nordic ApS Regus Business Centre Lautrup hoj - Ballerup DK-0 Denmark Tel: 0 99 Fax: France Microchip Technology SARL Parc d Activite du Moulin de Massy Rue du Saule Trapu Batiment A - ler Etage 900 Massy, France Tel: Fax: Germany Microchip Technology GmbH Gustav-Heinemann Ring D-9 Munich, Germany Tel: Fax: Italy Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus V. Le Colleoni 00 Agrate Brianza Milan, Italy Tel: Fax: United Kingdom Arizona Microchip Technology Ltd. 0 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG TU Tel: 9 9 Fax: /0/0 *DS9B* DS9B-page 00 Microchip Technology Inc.

15 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Microchip: TC0CCOA TC0CVOA TC0HEOA TCCEOA TCHEOA TC0CCOA TC0CCPA TC0CEOA TC0CVOA TC0HCOA TC0HCPA TC0HEOA TCCCPA TCHCOA TCCCOA TCCEOA TCHCOA TCHEOA TCHEPA TCCCOA