User Instructions For TopTronic RS-10

Size: px
Start display at page:

Download "User Instructions For TopTronic RS-10"

Transcription

1 User Instructions For TopTronic RS-0 409ENG-Dec0 Hoval Ltd Northgate Newark Nottinghamshire NG4 JN Phone Fax

2 Index 409ENG-Dec0 Introduction Introduction... Controls... Display... User instructions Key function table... 4 Switching on the room station... 4 Additional information... 5 Automatic program selection... 6 Room temperature... 7 Heating program... 8 Calorifier charging... 0 Advanced user instructions Language... Clock setting... Time clock level... Time clock programming... Block programming... 4 Table program settings... 7 Table program settings... 8 Table program settings... 9 Room level... 0 Parameter tables Room level parameters table... Advanced parameter table... 4 Installation / technical Installation... 7 Technical data... 7

3 409ENG-Dec0 Introduction The TopTronic RS-0 room station serves as a decentralized information center with remote interrogation and remote operating functions and can be used with all equipment versions of the TopTronic system. With the most up to date micro electronics exclusive functions can be activated which guarantee the highest level of comfort with the minimum energy usage. This is achieved with adaption and optimization functions which match heating energy to the exact building requirements. As well as these room temperature related functions a variety of equipment specific information is available which can be read within the living room and when necessary adapted to individual circumstances. This encompasses dates, on/off switching of the heating cycle with differently regulated room temperatures, actual values and diagnostic fault messages of the boiler. Operation of the unit is easy to understand and is limited to a minimum of operating elements which are separated for user and advanced user levels. The instructions are separated into two parts. Part (user instructions) delivers all immediately important operating stages which are necessary for use and are selected with directly accessible operating keys. Part (advanced instructions) these should only be used by the advanced user or service engineer and relate to specific settings / heating parameters and are accessible by the covered operating keys. Controls Symbol Display Heating Night setback Clock signal Room temperature LCD Display Key (increase value) Key (decrease value) 4 Key for heating program 5 Key for reduced (night time) program 6 Information 7 Program key (time/date) 8 Program key (automatic programs) 9 Program key (house level) 0 Program key (service level) Forward key Backward key Cover

4 4 User Instructions 409ENG-Dec0 Key Function table (User Level) Function Enter with keys Adjust with keys / range Page No. Room temperature correction or or 5 0 o C 7 Heating (day) room temperature Reduced (night) room temperature or with or 5 0 o C or with or 5 0 o C 7 7 Information i 5 Party function press and hold or 0.5 0h 8 Continuous heating press and hold or 5 0 o C 8 Absent function press and hold or 0.5 0h Continuous reduced press and hold or 5 0 o C 9 9 Automatic or 8-9 Calorifier charging and simultaneously ON or OFF 0 Automatic programs - and simultaneously or,, 6 Switching on the Room station When the room station is first switched on the following display will show for 5 seconds: Room Station Software version Central unit s Software version The default display will then appear. The symbol indicates that the room station is in heating operation and the symbol indicates the room station is in reduced (night time) operation. Information: Monday 0 th March 997 Time 0.5 Room temperature 0.5 o C Clock synchronisation Attention: During summer switch off the following symbols are not shown and. Blinking symbols or indicate that the unit is not operating under a normal program eg. party. The symbol indicates that a radio clock synchronisation has been connected.

5 409ENG-Dec0 User Instructions 5 Additional Information The following additional information on the central TopTronic can be obtained by pressing the i button (only if the relevant sensors are fitted): i i Default display. External sensor temperature. External sensor temperature. i i i Boiler return temperature. External heat source temperature. Default display. i i i i Boiler temperature. Mixed circuit temperature. Mixed circuit temperature. Domestic hot water temperature. Additional information with TopTronic B or B connected Switch off operation: switch off at outside sensor (short circuit) or no signal for outside temp. When the unit is switched off the information below shows instead of the default display. System off system switched off completely with no frost protection. Further automatic information also appears: Indication of forced standby operation by telephone modem. If the calorifier is fitted with a thermostat instead of a sensor the following will be displayed: i Calorifier on/off. Boiler flue gas temperature. Indication of common fault (when outside sensor is in short circuit in central unit) Fault Indications The RS-0 room station has a comprehensive fault indication system which has priority over all other indications and remain active until the fault is rectified.

6 6 User Instructions 409ENG-Dec0 If the room station is connected to a TopTronic B or B faults concerning the firing unit must be rectified in accordance with operating manual instructions. If any of the following fault displays are shown (Fault System Off, Fault warm water temperature, Fault boiler temperature, Fault room temperature ) you must notify the heating engineer. Operating Indication For the heating programs to operate automatically according to the information stored within the room station the operating switch on the central unit must be in automatic, or. In all other positions the central unit has priority and the room station only serves as a room sensor, remote temperature correction and information unit. The deviation from automatic setting is indicated on the room station as shown below: <<selection switch setting standby>> <<selection switch setting sun>> <<selection switch setting moon>> <<selection switch setting hand>> <<selection switch setting warm water>> Notes. The information remains active until the central unit switch is set to one of the three automatic settings, or.. During an indication the information i key can be used to display actual values. Automatic Program Selection In automatic there are three different time programs to switch between for each heating circuit. As a general rule these can be used without the need for adjustment but if individual programs are required customised cycles can be entered (see the advanced user section ). Program Circuit Time Boiler Circuit Mixed circuit Mixed Circuit Mo Fr Sa, Su Mo Fr Sa, Su Mo Fr Sa, Su Program Circuit Time Boiler Circuit Mo Su Mixed circuit Mo Su Mixed Circuit Mo Su Program Circuit Time Boiler Circuit Mixed circuit Mixed Circuit Mo Su Mo Su Mo Su Changing between Automatic Programs By using the and keys and following procedure it is possible to change between the automatic programs for the heating circuit which the room station is controlling. This can be the boiler circuit, mixed circuit or mixed circuit. Press Simultaneously The following will be displayed for the default setting of program : or or Room Station for Boiler circuit Room station for Mixed circuit Room station for Mixed circuit Use the and keys to change between programs, or. After 4 secs the default display will be restored.

7 409ENG-Dec0 User Instructions 7 Room Temperature By using the program keys and the increase / decrease value keys the room temperature can be changed for heating and reduced (night time). A Heating (day room temperature) If in heating operation as indicated by display follow the procedure below: press or on the Default screen automatically returns after 4 seconds. B Reduced (night room temperature) If in reduced operation as indicated by display follow the procedure below: press or on the Display for reduced operation. Works setting: 0 o C Adjustment range: 5 o C 0 o C press to increase to decrease Display for heating operation. Works setting: 6 o C Adjustment range: 5 o C 0 o C press to increase to decrease Default screen automatically returns after 4 seconds. Default screen automatically returns after 4 seconds. If in heating operation as indicated by display follow the procedure below: press or on the If in reduced operation as indicated by display follow the procedure below: on the Display for heating operation. press or Display for reduced operation. press press Display for heating temperature. Works setting: 6 o C Adjustment range: 5 o C 0 o C press to increase to decrease Display for reduced operation. Works setting: 0 o C Adjustment range: 5 o C 0 o C press to increase to decrease Default screen automatically returns after 4 seconds.

8 8 User Instructions 409ENG-Dec0 C Holiday (room minimum temperature) When in holiday mode follow the procedure below to set the minimum room temperature: press or Holiday program display. It should be noted that the adjustment is from the time of alteration and not an extension of the automatic program, or. The default display will return after 4 seconds. To cancel party program The party program can be cancelled and put back into automatic by the following procedure: press and hold Works setting: 0 o C Adjustment range: 5 o C 0 o C press to increase to decrease Heating Program With the two program keys and the following changes can be made to the programs: A - Party B - Heating C - Absent D - Reduced The default display returns after 4 seconds. B - Heating This program is used to switch on the heating continuously. press and hold A Party This program is used to switch on or extend the heating automatic program to a certain time for a one off event press and hold Display for party program. The default display returns after 4 seconds. For example: At 0.5 the heating needs to be extended by hours (to.5). press to increase to decrease Adjustment range 0.5 0h

9 409ENG-Dec0 User Instructions 9 To cancel heating program The continuous heating program can be cancelled using the following procedure: press and hold The default display will return after 4 seconds. D - Reduced This program is used to switch to reduced continuously. The default display will return after 4 seconds. press and hold C Absent This program is used to switch to reduced or extend the reduced automatic program to a certain time for a one off event press and hold Display for absent program. For example: At.00 the heating is switched to reduced for the next 6 hours (to 9.00). press to increase to decrease Adjustment range 0.5 0h It should be noted that the adjustment is from the time of alteration and not an extension of the automatic program, or. The default display will return after 4 seconds. The default display returns after 4 seconds. To cancel reduced program The continuous reduced program can be cancelled using the following procedure: press and hold To cancel absent program The absent program can be cancelled and put back into automatic by the following procedure: press and hold The default display will return after 4 seconds.

10 0 User Instructions 409ENG-Dec0 Calorifier Charging With this program it is possible to switch the calorifier on for a fixed three hour period. press simultaneously The default display will return after 4 seconds. To Cancel program: press simultaneously The default display will return after 4 seconds. Attention: The calorifier will be heated up to its maximum permissible temperature.

11 409ENG-Dec0 Advanced User Instructions Language The room station is programmed in three languages English, German and French. To change the language press or key for 5 seconds. Once the language appears the keys can be used to change languages. or - Month Change with: to increase to decrease Range: - Year Works setting: ENGLISH The previous display will return in a few seconds. - Clock setting The following functions can be set: - Time (minutes, hours) - - Month - Year The clock can be set to automatically change over from summer to winter time by a parameter in the service level of the central unit. Changing clock settings The clock can be changed by using and then the and keys to increase or decrease the values. - Time Change with: to increase to decrease Range: 00:00 :59 key - Return to default display Change with: to increase to decrease Range: If the key is not pressed the default display will return after minutes. It is possible to return to the default display at any time using the information key. - Time clock level In the time clock level the individual program times can be customized. Standard heating programs, and can be called up as desired and overwritten with different switch times and temperatures. Each standard program can thus be configured individually and stored under the same program number so that three different programs are available on demand. These can then simply be called up in the user operating level see page 6 for setting of the automatic program. Note: Programming of room temperatures is only possible if the relevant parameter has been enabled in the service level by an engineer. - Date Change with: to increase to decrease Range: If this has not been done it is only possible to change the on / off times. In this case the room temperature will be the works setting of 0ºC or the corrected value which has been set in the user level. The standard programs are lost when overwritten by customized programs. These are cancelled after a reset and replaced by the standard programs and therefore have to be recreated if needed.

12 Advanced User Instructions 409ENG-Dec0 Room temperature correction for PARTY and HEATING with variable temperature parameter enabled. For operating types: - PARTY - HEATING The room temperature is set to automatic works setting of 0ºC or the corrected value which has been set in the user level. The actual room temperature values for each of these two operating types can be set independently to the automatic program if the relevant parameter has been enabled in the service level by an engineer. The value is set separately when calling up the operating type PARTY or HEATING by using the and keys. These values remain stored for each further call of this operating type. Room temperature correction during automatic with variable temperature parameter enabled. During automatic operation the room temperature can be corrected using the and keys. The value can also be corrected for PARTY or HEATING operation by pressing the key and for REDUCED operation by pressing the key. Entering the time clock level Entering this level is achieved by simply pressing the key. Initially the heating cycle which the room station has been set to is shown. The three programs, or can be selected using the and keys. Press key Boiler circuit Works setting: Change with and keys or (if present) Mixer circuit Works setting: Change with and keys With the and keys all of the heating circuits together with the hot water circuit can be called up and are available for programming. Time Clock Programming It is possible to program up to three cycles periods for each desired weekday. Each of these cycles has an on / off as well as a temperature indication for this time span. The temperature can only be adjusted if the relevant parameter is enabled in the service level. The temperature indication refers to the heating cycle. The temperature between heating cycles is controlled according to the setting at the central unit. For the hot water programs the temperature indication refers to the hot water temperature. Calling up of heating cycles With a further pressing of the key the first heating cycle of the selected program shows complete with indication of weekday, cycle number, on time, off time and temperature. Each value is called up with the key in series The - On time - Off time - Temperature key can be used to step backwards. The current value which can be changed with the and keys is shown blinking. Switch times can be altered in 5 minute intervals and temperatures in 0.5K increments in the range of 5-0ºC. The next heating cycle can be called up by pressing the key and the process repeated. or (if present) Mixer circuit Works setting: Change with and keys Note: The on/off times of not used heating cycles should be set to 00:00 by simultaneously pressing the and keys. The 00:00 value does not refer to a clock time but only shows an undefined switch time.

13 409ENG-Dec0 Advanced User Instructions After programming the last heating cycle (day cycle ) the first heating cycle (Monday cycle ) will follow. By pressing the key in quick succession the programmed cycles can be called up in series the values noted and corrected if necessary. Time clock level can be exited by pressing the key. Change with Next cycle Cycle Monday TEMP (only when set in service level parameters) ON Cycle Monday Press to enter Cycle program ON Change with Next setting Change with Next setting OFF Change with Next setting OFF Change with Next cycle TEMP (only when set in service level parameters) Change with Next setting Change with Next cycle Cycle Monday TEMP (only when set in service level parameters) ON Remaining days in week Program as Monday Tuesday ON cycle day OFF cycle Change with Next setting Change with Next setting OFF Time clock program The tables shown on pages 7-9 give an overview of the works programmed standard programs together with temperature settings which cannot be lost. When creating customized programs note the appropriate values in the tables.

14 4 Advanced User Instructions 409ENG-Dec0 Canceling of individual heating cycles If necessary individually created cycles can be cancelled. After selecting the required cycle by pressing the key several times the cycle can be cancelled by pressing the and keys simultaneously. Enter the time program or mixer circuit or mixer circuit or hot water Press several times until the desired cycle appears Restore standard program To restore a customized program to a works standard program select the program as described on page (entering time clock level). Enter the time program or mixer circuit or mixer circuit or hot water Press Simultaneously standard program restored Press Simultaneously Cycle cancelled or mixer circuit or mixer circuit or hot water Time clock level can be exited by pressing the key. The default display will then be restored. i Block programming In order to simplify the programming of the time clocks it is possible to copy the time clock settings in various ways. A Complete automatic programs It is possible to copy complete programs to other programs for example boiler circuit program to mixed circuit program. This can be achieved by using the key to enter the time clock and then the keys to select the program to use as the source. The key is used to select the target program to which it is to be copied. The key is used to complete the copy. The procedure is shown in further detail by the illustration on page 5. Note: It is not possible to copy heating circuit programs to hot water programs or vice versa. B to day or week Time programs can also be copied from day to the whole week or from day to day for example Tuesday to Wednesday. to week While in the time clock see page the key followed by the key can be used to copy the current day to the whole week. The procedure is shown in further detail by the illustration on page 6. to day While in the time clock see page the current day can be copied to another day by using the key two or more times to select the target day. The key is used to complete the copy of the current day to the target day. The procedure is shown in further detail by the illustration on page 6.

15 409ENG-Dec0 Advanced User Instructions 5 Boiler Circuit Mixed Circuit Mixed Circuit Hot Water Program Program Program Program Program Program Program Program Program Program Program Heating circuit Press to enter clock program * * * * only if present Source program Use or to change program no. Source program Boiler circuit program Target program mixer circuit program Program will blink use to enter program to be copied to Copy will appear Press key to confirm copy Program will blink Program copied OK appears to confirm program copied Target program = Source program New source program for further copying Copy Mixer prog. from boiler circuit prog. Copy hot water prog. from hot water prog.

16 6 Advanced User Instructions 409ENG-Dec0 Enter from heating cycle program to copy (source day) copying Press Week Copying Press again to select target day Target day to Copy to Press to copy copied to whole week Press to copy Source day copied To target day Beginning of week now displayed Copy again Target day = Source for next copy Room temperature corrections with individual temperature cycle programs (heating cycle only) When individual temperatures have been entered for each heating cycle, the desired room temperature can be altered via the correction keys or for one of the cycles. This change will then effect all other heating cycles as shown in the below example: Original cycle temperatures Cycle 8ºC Cycle 0ºC Cycle ºC Room temp + K New Cycle ºC New cycle temperatures Cycle 8ºC + K = 0ºC Cycle 0ºC + K = ºC Cycle ºC + K = 4ºC Etc. As the temperature was increased by K during cycle the desired value has been increased by K in the other cycles.

17 409ENG-Dec0 Advanced User Instructions 7 Program settings Standard Program Custom Program From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp Boiler Circuit Mon o C o C Mon Tue o C o C Tue Wed o C o C Wed Thur o C o C Thur Fri o C o C Fri Sat o C Sat o C Mon Tue Wed Thur Fri Sat From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp o C o C o C o C o C o C o C o C o C o C o C o C Mixed Circuit Mon Tue Wed Thur Fri Sat Mon Tue Wed Thur Fri Sat From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp o C o C o C o C o C o C o C o C o C o C o C o C Mixed Circuit Mon Tue Wed Thur Fri Sat Mon Tue Wed Thur Fri Sat From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp o C o C o C o C o C o C o C o C o C o C o C o C Hot Water Mon Tue Wed Thur Fri Sat

18 8 Advanced User Instructions 409ENG-Dec0 Program settings Standard Program Custom Program From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp Boiler Circuit Mon o C Mon Tue o C Tue Wed o C Wed Thur o C Thur Fri o C Fri Sat o C Sat o C From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp Mon o C Tue o C Wed o C Thur o C Fri o C Sat o C o C Mixed Circuit Mon Tue Wed Thur Fri Sat From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp Mon o C Tue o C Wed o C Thur o C Fri o C Sat o C o C Mixed Circuit Mon Tue Wed Thur Fri Sat From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp Mon o C Tue o C Wed o C Thur o C Fri o C Sat o C o C Hot Water Mon Tue Wed Thur Fri Sat

19 409ENG-Dec0 Advanced User Instructions 9 Program settings Standard Program Custom Program From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp Boiler Circuit Mon o C Mon Tue o C Tue Wed o C Wed Thur o C Thur Fri o C Fri Sat o C Sat o C From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp Mon o C Tue o C Wed o C Thur o C Fri o C Sat o C o C Mixed Circuit Mon Tue Wed Thur Fri Sat From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp Mon o C Tue o C Wed o C Thur o C Fri o C Sat o C o C Mixed Circuit Mon Tue Wed Thur Fri Sat From To Temp From To Temp From To Temp From To Temp From To Temp From To Temp Mon o C Tue o C Wed o C Thur o C Fri o C Sat o C o C Hot Water Mon Tue Wed Thur Fri Sat

20 0 Advanced User Instructions 409ENG-Dec0 - Room Level At this level, the parameters relevant to the heating requirements of the building and its characteristics can be displayed and changed. - Hot water temperature - Burner hours run - Burner starts - Holiday program - Clock programs - Heating curves - Room temperature correction - Reset function Works setting: Range: Works setting: h Range: Burner hours run on nd stage Entering the Room Level Room level can be entered by using the key. Changes can be made using the, and keys. To exit the room level press the i key at any time. Press and hold for secs Works setting: Range: Number of burner starts on nd stage Holiday program start Hot water temperature Works setting: TopTronic B and B 55ºC Other TopTronics 60ºC Adjustment range 0ºC Hot water maximum temperature press to increase to decrease The maximum temperature is set in the technical parameter level. Works setting: h Range: Burner hours run on ST stage Number of burner starts on st stage Adjust with to increase and to decrease Change between day and month with and This function is used to switch the heating to frost protection only while the building is unoccupied for example a holiday. The default display will be today s date. Holiday program finish Adjust with to increase and to decrease Change between day and month with and This function is used to switch the heating back on when the building becomes occupied. Example of holiday program The heating will be switched to frost protection only on the 9. at 4.00 hrs

21 409ENG-Dec0 Advanced User Instructions The heating will remain off from hrs to hrs. This will be the default display until the heating is started again on 4.4. Hot water clock program Options: Program Program Program Mixed circuit clock program Works setting: Program Change with or With this parameter it is possible to change between the three clock programs for mixed circuit, see pages 7 to 9 for settings. Works setting: Program Options: Program Program Program Change with or With this parameter it is possible to change between the three clock programs for hot water, see pages 7 to 9 for settings. Blinks if auto adaption is set in service level parameters (do not change) Heating curve for boiler circuit Boiler circuit clock program Works setting: Program Options: Program Program Program Change with or With this parameter it is possible to change between the three clock programs for the boiler circuit, see pages 7 to 9 for settings. Mixed circuit clock program Works setting: Program Options: Program Program Program Change with or With this parameter it is possible to change between the three clock programs for mixed circuit, see pages 7 to 9 for settings. Works setting:.4 Range: Change with or With this parameter it is possible to change the slope of the heating curve for the boiler circuit (see graph). Blinks if auto adaption is set in service level parameters (do not change) Heating curve for mixed circuit Works setting:.4 Range: Change with or With this parameter it is possible to change the slope of the heating curve for mixed circuit (see graph). Heating curve for mixed circuit Blinks if auto adaption is set in service level parameters (do not change)

22 Advanced User Instructions 409ENG-Dec0 Works setting:.4 Range: Change with or With this parameter it is possible to change the slope of the heating curve for the boiler circuit (see graph). The heating curve gives the (boiler and / or mixed circuit) flow temperature / outdoor temperature ratio. The curve should only be reset with minimum changes spread out over a certain period of time to enable the regulator to react (by nature a heating installation is very slow to react). Corrections of 0. increments every or days is recommended. Note: The room station should be placed in the room that most accurately represents the temperature of the building. Thermostatic radiator valves when fitted properly should only serve to deregulate foreign heat sources and therefore should be fully open. During the regulation phase all foreign heat source should be switch off and ventilation should be kept to a minimum so as not to disturb the regulation process. When the heating curve is correctly set the room temperature should remain constant regardless of outside temperature. If automatic adaption is set in the service level the value will blink and is constantly corrected. In this case it must not be manually altered. Recommended values: Floor heating: Radiator heating:....0 Convection heating: Heating curve graph Works setting: 0.0K Range: -.5K +.5K Change with or Room temperature Correction Room temperature compensation With this parameter it is possible to calibration the room temperature by ±.5K. Reset function With this function it is possible to reset all the room level parameters back to their factory settings with the exception of burner hours run and burner starts. To reset room level parameters hold and Simultaneously until the following display appears Parameters reset Default display Max temp Boiler Flow Temp ºC Min temp Outside temperature ºC

23 409ENG-Dec0 Room Level Parameters Parameter Function With TopTronic Range. Burner hours run B, B B, B, B B, B 0B. Burner starts B, B B, B, B B, B 0B. Burner hours run on nd stage Factory B, B Burner starts on nd stage B, B Holiday program start B, B B, B, B B, B 0B 0/0 / Not set 6. Holiday program finish B, B B, B, B B, B 0B 7. Clock program for HWS B, B B, B, B B, B 0B 8. Clock program for boiler circuit 9. Clock program for mixed circuit 0. Clock program for mixed circuit. HWS temp (only with greater access program) B, B B, B, B B, B 0B B, B B, B, B B, B 0B B, B B, B, B B, B 0B 0/0 / Not set B, B 0 o C 55 o C B, B, B B, B 0B. Heating curve boiler circuit B, B B, B, B B, B 0B. Heating curve mixed circuit 4. Heating circuit mixed circuit B, B B, B, B B, B 0B B B B 60 o C Room temperature B, B compensation B, B, B B, B 0B 6. Reset to factory settings Current

24 4 Advanced Parameter Table 409ENG-Dec0 Factory settings No. Parameter Function Adj. Range B B B B B B B 0B Current Frost Protection -0 C...0 C Summer switch-off Aus, 0 C...0 C 7 C 7 C 7 C 7 C 7 C 7 C 7 C 7 C 7 C Minimum outdoor temperature Maximum flue gas temperature 70 C...50 C 50 C 50 C 50 C 50 C 50 C 50 C 50 C 5 Maximum boiler temperature 0 C...95 C (90 C Gas) 80 C 80 C 85 C 85 C 85 C 85 C 85 C 85 C 6 Boiler return temperature C 0 8 C 8 C 8 C 8 C 8 C 7 Blr circ Temp rise (Above mix circ) 0(-5K B,)...0K) 0K 8 K 8 K K K 8K 8 K 8 Pump overrun min 5 min 5 min 5 min 5 min 5 min 5 min 5 min 5 min 5 min 9 Boiler minimum temperature 0 C(0 C 0B)...95 C 48 C 48 C 48 C 48 C 48 C 0 C Type of hot water priority,, : None 0 X X X X X X X X : Priority X X X X X X X X : Priority with reservation X X X X X X Maximum hot water temperature 40 C...80 C 60 C 60 C 60 C 60 C 60 C 60 C 60 C 60 C Type of calorifier sensor, : Thermostat X X X X X X X X : Sensor X X X X X X X X Protection against Legionella Night water load Dom H/water installation load temp K 0 K 0 K 5 K 5 K 5 K 5 K 5 K 5 K 0 Influence room temp on blr circ KK Blr circ automatic adaption KK 0, : Off X X X X X X X X : On X X X X X X X X Boiler circuit user index KK,, :.00 X X X X X X X X :. X X X X X X X X :.00 X X X X X X X X Blr circ derivative action time KK 0...6h h h h h h h h h Blr circ ext sensor detection KK 0,, : Average value X X X X X X X X : External sensor X X X X X X X X : External sensor X X X X X X X X 7 Boiler circ constant temp reg KK (90 C Gas) C Influence room temp blr circ MK Mixed circ auto adaption MK 0, 0: Off X X X X X X X : On X X X X X X X Mixed circuit minimum temp MK C (90 C Gas) Mixed circuit maximum temp MK 0 C...95 C (90 C Gas) 80 C 80 C 80 C 80 C 80 C 80 C 80 C Mixed circuit user index MK,, 4 :.00 X X X X X X X :. X X X X X X X :.00 X X X X X X X 5 Mix circ derivative action time MK 0...6h h h h h h h h Mix circ ext sens. detection MK 0,, : Average value X X X X X X X : External sensor X X X X X X X : External sensor X X X X X X X 40 Influence room temp mix circ MK X = Possible settings

25 409ENG-Dec0 Advanced Parameter Table 5 Factory settings No. Parameter Function Adj. Range B B B B B B B 0B Current Mixed circ auto adaption MK 0, 4 0: Off X X X : On X X X 4 Mixed circ minimum temp MK C (90 C Gas) Mixed circ maximum temp MK 0 C...95 C (90 C Gas) 80 C 80 C 80 C Mixed circuit user index MK,, : X X X :. X X X :.00 X X X 45 Mix circ derivative actiontimemk 0...6h h h h Mix circ ext sensor detect MK 0,, : Average value 46 X X X : External sensor X X X : External sensor X X X 47 Mix circ const. reg operat'n MK C (90 C Gas) Mixed circ fixed point regulation C (90 C Gas) Summer/winter switchover 0, 60 0: Off X X X X X X X X X : On X X X X X X X X X Control output programming X : Boiler circuit pump X X X X X X X X : Casc. Boil. Interm. Valve X X X X X X X X : Fault signal output 6 X X X X X X 4: Boiler circuit lock X X X X X X 5: Primary pump X X X X X X 6: Low return temp protection pump X X X X X 7: Switch-on with external sensor X Control output programming X4-0,,, : Heat pump/solar/wood X X X X X : Fault signal output X X X X X : Boiler circ. Clock X X X X X 4: Electrical battery X X X X Control output programming X4-,,,4 : Fault signal output X X X X X X 6 : Pump minimum speed X X X X X X : Clock channel X X X X X 4: Heat pump/solar/wood X X X X X X 64 Bus address...5 Boiler cascade 0, : Single boiler X X X X X X : Cascade X X X X X X Level lock up 0,,, : No lock up X X X X X X X X X 66 : Room level lock up X X X X X X X X X : Clock lock up X X X X X X X X X : Room level and clock lock up X X X X X X X X X Reduced operation 0, 67 0: ECO - (Switch-off) X X X X X X X X X : Abs (Reduction) X X X X X X X X X 68 Minimum Room Temperature 5 C...0 C 5 C 5 C 5 C 5 C 5 C 5 C 5 C 5 C 5 C X = Possible settings

26 6 Advanced Parameter Table 409ENG-Dec0 Factory settings No. Parameter Function Adj. Range B B B B B B B 0B Current Pump seizure protection 0, 69 0: Off X X X X X X X X X : On X X X X X X X X X C/return protect during Blr turnon 0, 70 0: Off X X X X X X : On X X X X X X 7 Extended burner operation time min 0 min 0 min 0 min 0 min 0 min 0 min 7 st stage differential...0k 6 K 6 K 6 K 6 K 6 K 0 K 7 nd stage differential...0k K K 74 nd stage delay min 0 min 0 min 0 min 75 Lock stage with Outdoor temp Aus, -5 C...0 C 0 C 0 C 0 C Hot water power select for stage... : With outdoor temp and delay 76 X X X : With outdoor temp without delay X X X : Without limitations X X X Control input programming X- 0,, 0 0 0: Dom water heat (auto/blr/elec) 80 X X X X : Priority inversion X X X : Burner operation X X X X X Alarm logic signals 0, 8 0: Off X X X X X X X X X : On X X X X X X X X X 8 RESET RESET X X X X X X X X X 8 Relay Test alle Relais / all relays X X X X X X X X X X = Possible settings

27 409ENG-Dec0 Installation / Technical Data 7 Installation Positioning without room sensor If there is no room sensor or the room sensor has not been activated the unit can be placed as desired. Positioning with room sensor When used with the unit sensor activated the unit must be placed at a height of approximately.0 to.50 m in a place representing the temperature of all rooms. It is advisable to choose an internal wall in the coolest room which is used in the day. The unit may not be positioned: In direct sunlight (take note of the position of the sun in winter) Near any equipment which produces heat like televisions, wall lights, radiators etc. On walls where hot water pipes or chimneys run. On outside walls which are not insulated. In corners, recesses, shelves or behind curtains (insufficient air circulation). Near doors which lead to unheated rooms. In rooms which are regulated with thermostatic valves. Mounting Open the cover and loosen the screw inside. Lift the unit off the back plate. Secure the back plate with the screws provided. The data bus cable must be threaded through the lower part of the back plate. With a data bus cable of over 50m cable of types JY-(ST) xx0.6 or LI YC T (TP) xx0.75 must be used. The screening must be connected to the earth terminal of the boiler. Note: on new installations use a box behind the room station. Electrical Connection Before connecting / wiring the power at the boiler must be off. The 4 core bus cable is connected to the 4 pole terminal on the back plate. After the wiring is complete the room station is slotted in from above and screwed to the back plate. Note: by incorrect wiring the remains in VERSION indication for approximately minute and then goes to fault indication. Technical Data Wiring: 4 pole screwed terminals on back plate for mm max wire cross section. Bus Interface: RS485 Power supply: From central unit Color: White RAL 906 Fixing distance: 60mm ( hole fixing) Wall Fixing: x mm dia x 8 long Weight: 70g Operating Temperature: -0 o C.+50 o C Storage Temperature: -5 o C.+60 o C Indication: Alpha numeric text indication as well as symbols

TAC 2112 Manual (GB),

TAC 2112 Manual (GB), TAC 2112 Manual T1 P1 0-004-7459-3 (GB), 1999-08-01 Contents TAC 2112 Manual Subject to modification. 1999 TAC AB Contents 1 About this manual... 1:1 1.1 Overview... 1:1 1.2 How to use this manual...

More information

OWNERS MANUAL FOR STERLING SERIES CONTROLLERS

OWNERS MANUAL FOR STERLING SERIES CONTROLLERS OWNERS MANUAL FOR STERLING SERIES CONTROLLERS 24950 AVENUE KEARNY, VALENCIA, CALIFORNIA 91355-2142 PHONE (661) 257-3533 FAX (661) 257-9472 TABLE OF CONTENTS Selecting the Location for the Controller...3

More information

INSTRUCTION MANUAL DT10RF OPTIMISING PROGRAMMER UK/IE OPERATING AND INSTALLATION

INSTRUCTION MANUAL DT10RF OPTIMISING PROGRAMMER UK/IE OPERATING AND INSTALLATION Hol Man Auto Day OPERATING AND INSTALLATION DIGISTAT OPTIMISER - Radio frequency controlled programmable room thermostat with domestic hot water programmer FOR GREENSTAR CDi AND GREENSTAR Si MODELS ALSO

More information

TROVIS 5500 Automation System TROVIS 5578 Heating and District Heating Controller. Mounting and Operating Instructions EB 5578 EN

TROVIS 5500 Automation System TROVIS 5578 Heating and District Heating Controller. Mounting and Operating Instructions EB 5578 EN TROVIS 5500 Automation System TROVIS 5578 Heating and District Heating Controller Mounting and Operating Instructions EB 5578 EN Firmware version 2.2x Edition May 2015 Definition of signal words DANGER!

More information

TROVIS 5500 Automation System TROVIS 5578 Heating and District Heating Controller. Mounting and Operating Instructions EB 5578 EN

TROVIS 5500 Automation System TROVIS 5578 Heating and District Heating Controller. Mounting and Operating Instructions EB 5578 EN TROVIS 5500 Automation System TROVIS 5578 Heating and District Heating Controller Mounting and Operating Instructions EB 5578 EN Firmware version 2.30 Edition November 2017 Definition of signal words DANGER!

More information

TR 612 S. Bedienungsanleitung (Seite 2 19) Operating Instructions (pag ) Mode d emploi (page 38 55) Bruksanvisning (S.

TR 612 S. Bedienungsanleitung (Seite 2 19) Operating Instructions (pag ) Mode d emploi (page 38 55) Bruksanvisning (S. 310 415 TR 612 S Bedienungsanleitung (Seite 2 19) Operating Instructions (pag. 20 37) Mode d emploi (page 38 55) Bruksanvisning (S. 56 73) 2-Channel Time Switch EIB 8 GB 7 9 10 6 1 2 11 5 4 3 2 1 1 2 3

More information

Radio-control universal dimmer (built-in type) Installation Instructions

Radio-control universal dimmer (built-in type) Installation Instructions 2-Channel Time Switch Order no.: 1073 00 1 Programming / checking mode 2 Button for setting current time 3 Button for setting day of the week 4 Days of the week (1 = Mon, 2 = Tues, 7 = Sun) 5 Cursor t

More information

LK Wireless Room Control Cq

LK Wireless Room Control Cq LK Wireless Room Control Cq Description LK Wireless Room Control Cq consists of a LK Room Thermostat Cq-n (transmitter) and a LK Receiver Unit Cq 8 (8 channel receiver unit). The range also includes a

More information

theben Fan Coil Actuator FCA 1 Fan Coil Actuator FCA 1 FCA Version: Jan-08 (Subject to change) Page 1 of 77

theben Fan Coil Actuator FCA 1 Fan Coil Actuator FCA 1 FCA Version: Jan-08 (Subject to change) Page 1 of 77 Fan Coil Actuator FCA 1 FCA 1 492 0 200 Version: Jan-08 (Subject to change) Page 1 of 77 Contents 1 Functional characteristics...4 1.1 Operation and display...5 1.2 Advantages of the FCA 1...5 1.2.1 Special

More information

Overview per day of the programmed switching times 5 = Friday. Channel statuses / OFF

Overview per day of the programmed switching times 5 = Friday. Channel statuses / OFF 310 785 01 TR 611 top TERMINA 1-channel 7 day timer According to version Preprogrammed with the current time and summer/ winter norm time Safety Information The connection and installation of electrical

More information

OPERATING INSTRUCTIONS ARE ON PAGE 5. SECTION 2 Technical Data Transmitter Unit. RVHT 2 MULTI-FIT Programmable R/F Thermostat-Pair SECTION 1

OPERATING INSTRUCTIONS ARE ON PAGE 5. SECTION 2 Technical Data Transmitter Unit. RVHT 2 MULTI-FIT Programmable R/F Thermostat-Pair SECTION 1 OPERATING INSTRUCTIONS ARE ON PAGE 5 RVHT 2 MULTI-FIT Programmable R/F Thermostat-Pair SECTION 1 This Programmable Ravenheat R/F controlled room Thermostat RVHT 2, consists of 2 items: a Mobile Transmitter

More information

LP20RF & DIGISTAT+RF. Installation & User Guide PRINT. Radio frequency controlled room thermostat with dual channel programmer. Part number RF562DR

LP20RF & DIGISTAT+RF. Installation & User Guide PRINT. Radio frequency controlled room thermostat with dual channel programmer. Part number RF562DR Radio frequency controlled room thermostat with dual channel programmer Part number RF562DR Spares Part number 31003 Spares Part number 22590DR! For GREENSTAR CDi, GREENSTAR i JUNIOR and GREENSTAR Si MODELS

More information

INSTALLATION & PROGRAMMING MANUAL PROGRAMMABLE TIMER (MODEL LP-2)

INSTALLATION & PROGRAMMING MANUAL PROGRAMMABLE TIMER (MODEL LP-2) INSTALLATION & PROGRAMMING MANUAL PROGRAMMABLE TIMER (MODEL LP-2) Copyright Lencore Acoustics Corp. All rights reserved. April 2000 CONTENTS Introduction 3 Display 3 Keyboard 4 Installation 4 Set Up 4

More information

Thermostat P. Thermostats Electronic room thermostat with clock for thermal actuators

Thermostat P. Thermostats Electronic room thermostat with clock for thermal actuators Thermostat P Thermostats Electronic room thermostat with clock for thermal actuators IMI HEIMEIER / Thermostats & Actuators / Thermostat P Thermostat P The Thermostat P room temperature controller is used

More information

Control solutions Biofloor

Control solutions Biofloor MR24 Central radio controller 24V Connect COMAP offers the Connect control system as part of its underfloor heating and cooling solution. Composed of a central radio control module (MR24), wireless digital

More information

STR-LCF. Security Advice Caution. Notes on Disposal. Electronic Fan Coil Thermostat (Flush mounting) Datasheet. Application

STR-LCF. Security Advice Caution. Notes on Disposal. Electronic Fan Coil Thermostat (Flush mounting) Datasheet. Application STR-LCF Electronic Fan Coil Thermostat (Flush mounting) Datasheet Subject to technical alteration Issue date: 28.2.217 Application The fan coil room thermostat has been designed for individual control

More information

Use of the application program. Contents. 1. Functional description General. GAMMA instabus Application program description.

Use of the application program. Contents. 1. Functional description General. GAMMA instabus Application program description. Use of the application program Product family: Product type: Manufacturer: Heating, air conditioning, ventilation Thermostat Siemens Name: Temperature controller UP 237 DELTA i-system Order no.: 5WG1 237-2AB_1

More information

Communicative heating controller

Communicative heating controller UC100 Communicative heating controller Summary UC100 is a communicative room heating controller with one PWM output for control of a radiator or electrical heater. It can work autonomously, or in connection

More information

Use of the application program. Contents. 1. Functional description General. GAMMA instabus Application program description.

Use of the application program. Contents. 1. Functional description General. GAMMA instabus Application program description. Use of the application program Product family: Product type: Manufacturer: Heating, air conditioning, ventilation Thermostat Siemens Name: Temperature controller UP 237 DELTA i-system Order no.: 5WG1 237-2AB_1

More information

TC 204 Heating Controller

TC 204 Heating Controller TC 204 Heating Controller ver. 1.32-01 The TC204 is a multi-purpose heating controller with built-in programs for different types of heating systems. General Data Power requirement 24 volts ac, 2 va Inputs

More information

Fan Coil Actuator FCA 2

Fan Coil Actuator FCA 2 Fan Coil Actuator FCA 2 FCA 2 4920210 Updated: Feb-16 (subject to changes) Page 1 of 89 Contents 1 Function description... 4 1.1 Operation and display... 5 1.2 Advantages of the FCA 2... 6 1.2.1 Special

More information

Self-learning Room Temperature Controller Receiver

Self-learning Room Temperature Controller Receiver 2 265 REV23RF REV-R.02/1 REV23RF/SE Self-learning Room emperature Controller Receiver Consisting of controller (with integrated radio transmitter) and receiver (switching unit with relay outputs) REV23RF

More information

PRODUCT CATALOGUE TEMPERATURE CONTROL Grässlin products for individual control of temperature

PRODUCT CATALOGUE TEMPERATURE CONTROL Grässlin products for individual control of temperature PRODUCT CATALOGUE TEMPERATURE CONTROL Grässlin products for individual control of temperature Temperature control: Feel good at any time of year Room thermostats Heating time switches Excellent products

More information

Sauter Components

Sauter Components R 44.488/ QRK 0: Heating controller Used in conjunction with temperature detectors (Ni000) and appropriate control valves for heating and domestic-hot-water control (with various configurations), mainly

More information

16-Channel Yearly Time Switch TR 648 S DCF

16-Channel Yearly Time Switch TR 648 S DCF 16-Channel Yearly Time Switch TR 648 S DCF Illustration 1 : TR 648 S DCF TR 648 S DCF EIB 648 9 201 DCF 77 Antenna 907 0 271 Obelisk 2.0 Programming set 907 0 305 Obelisk 2.1 Software 931 0 961 Page 1

More information

200 RTH OFF ON IN OUT ALARM RESET

200 RTH OFF ON IN OUT ALARM RESET 200 RTH OFF ON IN OUT ALARM RESET EN OWNER S MANU AL www.auraton.pl 2 3 Thank you for purchasing the modern temperature controller based on an advanced microprocessor. AURATON 200 RTH LCD FrostGuard function:

More information

SA-027HQ 365-Day Annual Timer

SA-027HQ 365-Day Annual Timer SA-027HQ 365-Day Annual Timer Manual Two N.O. or N.C. Form C relays, 10A@14VDC Each relay can be programmed for 50 events, for a total of 100 individual programmable events 10 Programmable holidays The

More information

AURATON 2020 AURATON 2020 TX RX Plus

AURATON 2020 AURATON 2020 TX RX Plus 0 I 31 EN AURATON 2020, AURATON 2020 TX RX Plus AURATON 2020 AURATON 2020 AURATON 2020 TX RX Plus Preliminary notes The manual includes the information on AURATON 2020 and AURATON 2020 TX RX Plus controllers.

More information

MAKING MODERN LIVING POSSIBLE. CP715Si. Electronic 2-Channel Common Timebase Programmer for Heating and Hot Water. Installation Guide.

MAKING MODERN LIVING POSSIBLE. CP715Si. Electronic 2-Channel Common Timebase Programmer for Heating and Hot Water. Installation Guide. MAKING MODERN LIVING POSSIBLE CP715Si Electronic 2-Channel Common Timebase Programmer for Heating and Hot Water Danfoss Heating Installation Guide For a large print version of these instructions please

More information

INSTAT 868 Radio Frequency Single-Room Controls

INSTAT 868 Radio Frequency Single-Room Controls INSTAT 868 Radio Frequency Single-Room Controls Easy to operate wireless application HEATING People Performance Products Climate Controls Europe An Invensys company Radio Frequency Controls Single-room

More information

Control module 2 circuits AD290. Installation and Service Manual

Control module 2 circuits AD290. Installation and Service Manual EN Control module 2 circuits AD290 Installation and Service Manual 129443-02 Contents 1 Introduction...4 1.1 Symbols used...4 1.2 Abbreviations...4 2 Safety instructions and recommendations...5 2.1 Recommendations...5

More information

RAMSES 784 HF Set 1. Bedienungsanleitung Uhrenthermostat 1. Operating Instructions Clockthermostat 14. Mode d emploi Thermostat à horloge 26

RAMSES 784 HF Set 1. Bedienungsanleitung Uhrenthermostat 1. Operating Instructions Clockthermostat 14. Mode d emploi Thermostat à horloge 26 309 484 01 RAMSES 784 HF Set 1 784 9 407 784 9 417 Bedienungsanleitung Uhrenthermostat 1 Operating Instructions Clockthermostat 14 Mode d emploi Thermostat à horloge 26 Gebruiksaanwijzing Klokthermostaat

More information

E N SHT-1 SHT-1/2 SHT-3 SHT-3/2

E N SHT-1 SHT-1/2 SHT-3 SHT-3/2 Digital time switch E N SHT-1 SHT-1/2 SHT-3 SHT-3/2 Content Symbol, Connection... 3 Warning... Characteristics... 5 Technical parameters... 6 Versions of time switches, Load... 7 Description... 8-9 Control...

More information

Model: 5301P INSTALLATION AND OPERATION INSTRUCTIONS

Model: 5301P INSTALLATION AND OPERATION INSTRUCTIONS Model: 5301P INSTALLATION AND OPERATION INSTRUCTIONS INTRODUCTION IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE This SKYTECH remote control system

More information

CM927 WIRELESS PROGRAMMABLE THERMOSTAT FEATURES PRODUCT SPECIFICATION SHEET

CM927 WIRELESS PROGRAMMABLE THERMOSTAT FEATURES PRODUCT SPECIFICATION SHEET CM927 WIRELESS PROGRAMMABLE THERMOSTAT FEATURES CM927 can be installed without disrupting your room décor as no wiring connection is required between the room unit and the boiler Attractive, slim, ultra-modern

More information

RAM 712 KNX room thermostat for surface-mounted and flush-mounted installation

RAM 712 KNX room thermostat for surface-mounted and flush-mounted installation RAM 712 KNX room thermostat for surface-mounted and flush-mounted installation RAM 712 712 9 200 Version: Dec-10 (subject to change) Page 1 of 65 Contents 1 Functional characteristics... 4 1.1 Operation...

More information

534I, 650, 739I, 1200, 1300, 1500, MF28I

534I, 650, 739I, 1200, 1300, 1500, MF28I GV60 PLUS OPERATING INSTRUCTIONS The GV60 PLUS Electronic Ignition Remote Control system is used on the Valor heaters models 530I, 534I, 650, 739I, 1200, 1300, 1500, MF28I and RF24ID Remote Control Initial

More information

WLDS-10 Mk3 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING

WLDS-10 Mk3 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING WLDS-10 Mk3 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING DESCRIPTION: An electronic control panel used in conjunction with one pulse meter (a water meter with pulse output proportional

More information

OPERATING INSTRUCTIONS Digital weekly time switch

OPERATING INSTRUCTIONS Digital weekly time switch OPERATING INSTRUCTIONS Digital weekly time switch 1 Explanation of display and control buttons One-channel timer A B Two-channel timer 1.1 Control buttons i Set time and day of the week e Manual switching

More information

WLDS-10 Mk2 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING

WLDS-10 Mk2 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING WLDS-10 Mk2 MAJOR WATER LEAK DETECTION SYSTEM INSTALLATION & COMMISSIONING DESCRIPTION: An electronic control panel used in conjunction with one pulse meter (a water meter with pulse output proportional

More information

8000 SERIES PRECISION MULTIMETER VERIFICATION AND ADJUSTMENT GUIDE

8000 SERIES PRECISION MULTIMETER VERIFICATION AND ADJUSTMENT GUIDE 8000 SERIES PRECISION MULTIMETER VERIFICATION AND ADJUSTMENT GUIDE TRANSMILLE LTD. Version 1.1 : Apr 2015 TABLE OF CONTENTS PREPARING FOR CALIBRATION... 4 INTRODUCTION... 4 CALIBRATION INTERVAL SELECTION...

More information

CAN-I/O 45 CAN-I/O Module 45 Software Version 1.13 Programming Functions Manual Version 1.13

CAN-I/O 45 CAN-I/O Module 45 Software Version 1.13 Programming Functions Manual Version 1.13 www.ta.co.at CAN-I/O 45 CAN-I/O Module 45 Software Version 1.13 Programming Functions Manual Version 1.13 English Table of contents Programming with TAPPS2... 5 Schematic diagram of a function module...

More information

Multi-Channel In-Out Thermometer with Cable Free Sensor and RF Clock

Multi-Channel In-Out Thermometer with Cable Free Sensor and RF Clock Multi-Channel In-Out Thermometer with Cable Free Sensor and RF Clock MAIN FEATURES: MAIN UNIT GB MODEL: RMR182 USER'S MANUAL INTRODUCTION Congratulations on your purchase of the RMR182 Multi- Channel In-Out

More information

NRT 105: Electronic fan-coil controller, equiflex

NRT 105: Electronic fan-coil controller, equiflex Product data sheet 4.04 R 105: Electronic fan-coil controller, equiflex How energy efficiency is improved ECO Meter for displaying the current energy consumption and digital input for the change-over between

More information

User Manual OFF ON IN OUT ALARM RESET AURATON RTH software ver. F0F

User Manual OFF ON IN OUT ALARM RESET AURATON RTH software ver. F0F www.auraton.pl User Manual software ver. F0F OFF ON IN OUT ALARM RESET AURATON RTH Thank you for purchasing this modern, advanced, microprocessor-based temperature regulator AURATON 2025 / AURATON 2025

More information

Intelligent Installation Systems. ABB i-bus KNX Room Thermostat Fan Coil with Display 6138/11-xx-500 Product Manual

Intelligent Installation Systems. ABB i-bus KNX Room Thermostat Fan Coil with Display 6138/11-xx-500 Product Manual Intelligent Installation Systems ABB i-bus KNX Room Thermostat Fan Coil with Display 6138/11-xx-500 Product Manual TemABB i-bus KNX Contents and document history Page 1 General...3 1.1 Overview of Product

More information

P178252GB DELTA RC WIRELESS WEATHER STATION INSTRUCTION MANUAL

P178252GB DELTA RC WIRELESS WEATHER STATION INSTRUCTION MANUAL P178252GB070 74292 DELTA RC WIRELESS WEATHER STATION INSTRUCTION MANUAL Thank you for your purchase of this delicate Wireless Weather Station. Once you have inserted the batteries the clock will automatically

More information

EBERLE THERMOSTAT & RECEIVER

EBERLE THERMOSTAT & RECEIVER EBERLE THERMOSTT & RECEIVER SIMPLIFIED INSTLLTION INSTRUCTIONS: Carefully connect the wires as on the next page diagram between the electric source and the heater. Once all is connected/installed, start

More information

Wireless Room Thermostat Installation and Operation Y6630D1007

Wireless Room Thermostat Installation and Operation Y6630D1007 Wireless Room Thermostat Installation and Operation Y6630D1007 General safety instructions Contents 1. General safety instructions... 3 1.1. Commissioning the relay module HC60NG... 3 2. Overview... 4

More information

Installation Guide. ECL Comfort 310, application A Table of Contents

Installation Guide. ECL Comfort 310, application A Table of Contents 1.0 Table of Contents 1.0 Table of Contents... 1 1.1 Important safety and product information..................... 2 2.0 Installation... 6 2.1 Before you start.....................................................

More information

WIRELESS CONTROL UNIT FOR CONTROL OF ELECTRIC HEATING DEVICES (WITHIN ONE ROOM)

WIRELESS CONTROL UNIT FOR CONTROL OF ELECTRIC HEATING DEVICES (WITHIN ONE ROOM) PH-BSP WIRELESS CONTROL UNIT FOR CONTROL OF ELECTRIC HEATING DEVICES (WITHIN ONE ROOM) Wireless control unit Two-way radio communication on 433.92 MHz Comfortable solution of room heating Predictive system

More information

TR TR 641 top TR 642 top TR 644 top TR 641 top2 RC TR 642 top2 RC TR 644 top2 RC

TR TR 641 top TR 642 top TR 644 top TR 641 top2 RC TR 642 top2 RC TR 644 top2 RC 2 2 309 429 01 TR TR 641 top2 641 0 100 TR 642 top2 642 0 100 TR 644 top2 644 0 100 TR 641 top2 RC 641 0 300 TR 642 top2 RC 642 0 300 TR 644 top2 RC 644 0 300 Installation and operating instructions Digital

More information

* _Ver.1* GP8 Radio CPL Radio DRIVER Energy manager

* _Ver.1* GP8 Radio CPL Radio DRIVER Energy manager GP8 Radio CPL Radio DRIVER Energy manager Delta Dore hereby declares that the equipment complies with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC The EC declaration

More information

2025 RTH 2025 P 2025 OFF ON IN OUT ALARM RESET

2025 RTH 2025 P 2025 OFF ON IN OUT ALARM RESET 2025 RTH 2025 P 2025 OFF ON IN OUT ALARM RESET EN OWNER S MANU AL www.auraton.pl 2 Thank you for purchasing this modern, advanced, microprocessor-based temperature regulator AURATON 2025 / 2025 P / 2025

More information

The CM Range. Clearly different

The CM Range. Clearly different The CM Range. Clearly different Effortless efficiency Our CM900 range of programmable thermostats offers maximum energy efficiency with minimum fuss. They all feature our unique Line of Text (LoT ) display,

More information

R PROFLAME Instruction Book Collection

R PROFLAME Instruction Book Collection 9.956.028 R00 584 PROFLAME Instruction Book Collection 4-17 18-29 584 PROFLAME System 30-39 Appendix: DIP SWITCH NUMBER (0=ON 1=OFF) 40-41 4-17 Fig. 1 The SIT is a device that allows, in conjunction with

More information

MANUAL. PT Series 365 Day Annual Timer. Tel:

MANUAL. PT Series 365 Day Annual Timer.   Tel: MANUAL PT Series 365 Day Annual Timer www.belltimers.com Tel: 1-888-327-8463 info@belltimers.com Table of Contents: Introduction Features Specifications Overview Installation Function Keys Relay Operation

More information

Instruction manual. art Installation manual

Instruction manual. art Installation manual Instruction manual art. 01521 Installation manual Contents GENERAL FEATURES AND FUNCTIONALITY from page 4 ETS PARAMETERS AND COMMUNICATION OBJECTS from page 6 COMMUNICATION OBJECTS GENERAL FEATURES AND

More information

EUROSTER 2026/2026TX

EUROSTER 2026/2026TX EUROSTER 2026/2026TX - User Manual 1 EUROSTER 2026/2026TX 1. CHARACTERISTICS 4 different programs for each day of the week (28 different ranges and temperatures altogether). Time programming with 10 minutes

More information

User manual. KNX MultiController DALI. Article number: 5410x / 5411x. function Technology AS

User manual. KNX MultiController DALI. Article number: 5410x / 5411x. function Technology AS User manual KNX MultiController DALI Article number: 5410x / 5411x Picture: KNX MultiController DALI with Reed panel and sensor function Technology AS Table of contents 1 KNX MULTICONTROLLER... 3 2 INTRODUCTION...

More information

SERVICE-MANUAL ROOM TEMPERATURE CONTROLLER NEA 230V / 24V. Construction Automotive Industry

SERVICE-MANUAL ROOM TEMPERATURE CONTROLLER NEA 230V / 24V. Construction Automotive Industry ROOM TEMPERATURE CONTROLLER NEA 230V / 24V Construction Automotive Industry ROOM TEMPERATURE CONTROLLER NEA 230V / 24V TABLE OF CONTENTS 1....... Information and safety guidelines......................................................

More information

GV60 PLUS. GV60 PLUS Electronic Ignition Remote Control. used on Valor heaters of Series Portrait, Horizon, H4, G3, L1, L2, L3, MF and RFD

GV60 PLUS. GV60 PLUS Electronic Ignition Remote Control. used on Valor heaters of Series Portrait, Horizon, H4, G3, L1, L2, L3, MF and RFD OPERATION MANUAL GV60 PLUS GV60 PLUS Electronic Ignition Remote Control used on Valor heaters of Series Portrait, Horizon, H4, G3, L1, L2, L3, MF and RFD For Valor heaters 530, 534, 650, 739, 1500, 1600,

More information

Wireless temperature controller E N RFTC-50/G

Wireless temperature controller E N RFTC-50/G Wireless temperature controller E N RFTC-50/G Contents Warning... 3 Characteristics... 4 Technical parameters... 5 Battery replacement... 6 Description of device... 7 Description of display... 8 Description

More information

User manual CLIMATIC 60

User manual CLIMATIC 60 User manual CLIMATIC 60 Providing indoor climate comfort MUL46E-0413 04-2013 Original manual translation TABLE OF CONTENTS AQUALEAN CONTROL MANUAL DISPLAY DC60 INSTALLATION CONNECTION IMPORTANT WARNING

More information

VIESMANN. Installation and service instructions VITOTROL 300 RF. for contractors. Vitotrol 300 RF

VIESMANN. Installation and service instructions VITOTROL 300 RF. for contractors. Vitotrol 300 RF Installation and service instructions for contractors VIESMANN Vitotrol 3 RF Wireless remote control for one, two or three heating circuits For applicability, see the last page VITOTROL 3 RF 4/212 Please

More information

KNX manual High-performance switch actuators RM 4 H FIX1 RM 8 H FIX2

KNX manual High-performance switch actuators RM 4 H FIX1 RM 8 H FIX2 KNX manual High-performance switch actuators RM 4 H FIX1 RM 8 H FIX2 4940212 4940217 2018-10-17 Contents 1 Function description 3 2 Operation 4 3 Technical data 5 4 The FIX2 RM 8 H application programme

More information

EQJW145. Content: 1 General. 2. Indicators and operating controls 3. Putting into service (by a technician) 4. How to operate (user)

EQJW145. Content: 1 General. 2. Indicators and operating controls 3. Putting into service (by a technician) 4. How to operate (user) SAUER equitherm Electronic heating controller 1) Valid from soft version 09 Content: General 2. Indicators and operating controls 3. Putting into service (by a technician) 4. How to operate (user) en Quick

More information

Intelligent Compact Controller

Intelligent Compact Controller TCY-T0121 Intelligent Compact Controller Features Temperature control for 2-pipe, 4-pipe HVAC systems. Temperature range from 40 to 140 C. 1 independent PI and On/Off control loop to control temperature.

More information

E V1. System Manager Installation Manual

E V1. System Manager Installation Manual E8.5064 V1 System Manager Installation Manual Please observe the safety instructions and read through this manual carefully before commissioning the equipment. Safety information General information Safety

More information

R7426A. MicroniK 200 TEMPERATURE CONTROLLER WITH AND WITHOUT REAL-TIME CLOCK

R7426A. MicroniK 200 TEMPERATURE CONTROLLER WITH AND WITHOUT REAL-TIME CLOCK MicroniK 200 R7426A TEMPERATURE CONTROLLER WITH AND WITHOUT REAL-TIME CLOCK PRODUCT DATA Fig. 1. Temperature controller FEATURES Microcontroller design based on modern digital technology User interface

More information

Arcus-EDS. Application Description. SK0x-Txxx

Arcus-EDS. Application Description. SK0x-Txxx Arcus-EDS Application Description Outdoor Sensor SK01-TFK Room Sensor SK03-TFK (flush-mounting) Multiple Sensor SK01-TTFK Room Sensor SK02-TFK KN-Sensors Temperature-Humidity-Climate 100 e4 KN-Sensors

More information

The room thermostat application module with 2-fold switch sensor is placed on a flush-mounted bus coupler.

The room thermostat application module with 2-fold switch sensor is placed on a flush-mounted bus coupler. The room thermostat application module with 2-fold switch sensor is placed on a flush-mounted bus coupler. The room thermostat with 2-fold switch sensor offers the possibility of implementing single room

More information

Sentry Digital Timers

Sentry Digital Timers Sentry Digital Timers 0733s S4 Contents 1. Safety precautions 2. General rmation 3. DIN rail Installation 4. Display Layout. Programming 6. Technical Data 7. Guarantee 2 Safety precautions The connection

More information

KNX manual 1-channel flush-mounted switch actuator SU 1

KNX manual 1-channel flush-mounted switch actuator SU 1 KNX manual 1-channel flush-mounted switch actuator SU 1 4942520 2018-10-04 Contents 1 Function description 3 2 Operation 4 3 Technical data 5 4 The SU 1 application programme 7 4.1 Selection in the product

More information

Use of the application program. Contents. instabus EIB Application program description. September S2 Room temperature controller

Use of the application program. Contents. instabus EIB Application program description. September S2 Room temperature controller Use of the application program Product family: Product type: Manufacturer: Heating, Air conditioning, Ventilation Thermostat Siemens Name: Room temperature controller IKE 250 DELTA millennium Order no.:

More information

LIGHTING CONTROL PANEL

LIGHTING CONTROL PANEL LIGHTING CONTROL PANEL Installation Guide & User Manual 925 A.E.C. D R IVE, W O O D D A LE, IL 60191 (630) 238-1516 / FA X (630) 860-2934 THIS PAGE INTENTIONALLY LEFT BLANK 2 WARRANTY STATEMENT Automated

More information

Radiocontrol F. Floor Heating Controller Radio control system for floor heating

Radiocontrol F. Floor Heating Controller Radio control system for floor heating Radiocontrol F Floor Heating Controller Radio control system for floor heating IMI HEIMEIER / Floor Heating Control / Radiocontrol F Radiocontrol F The Radiocontrol F radio control system for controlling

More information

Manual BC20 Control Service Guide

Manual BC20 Control Service Guide Manual BC20 Control Service Guide To Access the following menus, with the in the OFF mode, press and hold the upper encoder (Timer Knob) until "0000" appears. Then turn the encoder till the first number

More information

WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual

WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual WIRELESS 868 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this temperature station with wireless 868MHz transmission. It not only displays the indoor temperature

More information

Expandable Controller 3, 7, 11, 15 stations Installation and Programming Guide

Expandable Controller 3, 7, 11, 15 stations Installation and Programming Guide seconds. This blinking cycle is to go on until the low battery condition is corrected. At that time the normal display returns. Also, while LO BA is blinking, if the dial is turned or any button is pressed,

More information

Room thermostat solo, FM Type: 6124-xx

Room thermostat solo, FM Type: 6124-xx The application module room thermostat solo, FM is placed on a flush-mounted bus coupler. The room thermostat is used for individual room temperature control in heating and air conditioning systems. The

More information

Digital Room Sensor Technical Guide

Digital Room Sensor Technical Guide www.orioncontrols.com Digital Room Sensor Technical Guide TABLE OF CONTENTS OVERVIEW... 3 BASIC OPERATION... 4 Sensor Operation... 4 LED Operation... 4 MOUNTING AND WIRING... 5 Environmental Requirements...

More information

Contents. Time switches. Presentation 2 Offer overview 4 Choice table 6 Technical data and catalogue numbers 8

Contents. Time switches. Presentation 2 Offer overview 4 Choice table 6 Technical data and catalogue numbers 8 Contents Presentation 2 Offer overview 4 Choice table 6 Technical data and catalogue numbers 8 Practical advice 15 A few principles 15 Programming examples 16 Updated: 27/8/03 1 Presentation For all sectors

More information

4TCD1. Digital 7-Day Programmable Timer. Installation Instructions. Tel Fax Schneider Electric (Australia) Pty Ltd

4TCD1. Digital 7-Day Programmable Timer. Installation Instructions. Tel Fax Schneider Electric (Australia) Pty Ltd Digital 7-Day Programmable Timer 4TCD1 Schneider Electric (Australia) Pty Ltd Contact us: clipsal.com/feedback National Customer Care Enquiries: Tel 1300 2025 25 Fax 1300 2025 56 Installation Instructions

More information

CS-200. PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL

CS-200. PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL CS-200 PORTABLE TRAFFIC LIGHT CONTROLLER (Software 1.05) OPERATION AND SERVICE MANUAL CS-200 Operation and Service Manual Page 2 Manufactured by: LINCAST INTERNATIONAL PTY. LTD. 2/3 Sir Laurence Drive

More information

Please enter the identity code of your device here!

Please enter the identity code of your device here! Operating Instructions DULCOMETER D1C Part 2: Adjustment and Operation, Measured Variable Conductive Conductivity ProMinent D1C2-Leit.-001-GB Conductivity 100 µs/cm DULCOMETER STOP START Conductivity 100

More information

B 556. LOCAL BUILT-IN OR WALL-MOUNTED UNIT WITH Volt RELAY OUTPUT "MULTIZONE" SYSTEM. RTL 120 Eng. = built-in unit

B 556. LOCAL BUILT-IN OR WALL-MOUNTED UNIT WITH Volt RELAY OUTPUT MULTIZONE SYSTEM. RTL 120 Eng. = built-in unit LOCAL BUILT-IN OR WALL-MOUNTED UNIT WITH 0...10 Volt RELAY OUTPUT "MULTIZONE" SYSTEM P LOC RTL 120 Eng. = built-in unit B 556 - RTL 120/520 Eng. 24.05.10 AM REV. 03 B 556 24.05.10 AM REV. 03 RTL 520 Eng.

More information

Mx-D15 Intelligent Valve Actuator

Mx-D15 Intelligent Valve Actuator Application Small radio controlled, battery-powered actuator for room temperature control. For thermostat valve bodies for direct mounting on commercially available radiator valves for room-specific temperature

More information

MCU Software Configuration and System Calibration

MCU Software Configuration and System Calibration Analox Ltd. 15 Ellerbeck Court, Stokesley Business Park North Yorkshire, TS9 5PT, UK T: +44 (0)1642 711400 F: +44 (0)1642 713900 W: www.analox.net E: info@analox.net List of Contents 1 Introduction...

More information

User s Manual. F2 Calculator. A metering component for thermal energy applications

User s Manual. F2 Calculator. A metering component for thermal energy applications User s Manual F2 Calculator A metering component for thermal energy applications Rev 08.24.2007 1 Installation 1.1 At delivery F2 calculators are delivered in the Transport Mode. Only the clock is active

More information

DDC Series Dial Digital Controller INSTALLATION AND OPERATING INSTRUCTIONS

DDC Series Dial Digital Controller INSTALLATION AND OPERATING INSTRUCTIONS DDC Series Dial Digital Controller INSTALLATION AND OPERATING INSTRUCTIONS Thank you for choosing the Toro DDC (Digital Dial Controller) irrigation controller. The DDC incorporates the lates programming

More information

NX Series Inverters. HVAC Pocket Programming Guide

NX Series Inverters. HVAC Pocket Programming Guide NX Series Inverters HVAC Pocket Programming Guide HVAC Pocket Programming Guide HVAC Pocket Programming Guide / Contents This guide provides a single reference document for the user of NXL HVAC (product

More information

Digital Electronic Thermostat With RF

Digital Electronic Thermostat With RF RT300RF Manual Altech 005_89 06/05/2014 08:56 Page 1 Digital Electronic Thermostat With RF Instruction Manual Model No ALTHC015 RT300RF Manual Altech 005_89 06/05/2014 08:56 Page 2 2 ALTHC015 INSTRUCTION

More information

4.3 Touchscreen User Manual

4.3 Touchscreen User Manual 4.3 Touchscreen User Manual Contents 1. Temperature 1. How do I adjust the temperature at console 2. How do I use the buttons on the sensor (Digital Sensor Only) 3. Sensor Symbols Explained (Digital Sensor

More information

User Manual. KNX MultiLight Dali. Article number: function Technology AS. Picture: KNX MultiLight products

User Manual. KNX MultiLight Dali. Article number: function Technology AS. Picture: KNX MultiLight products User Manual KNX MultiLight Dali Article number: 44002 Picture: KNX MultiLight products function Technology AS Table of Contents 1 THE KNX MULTILIGHT DALI... 3 2 INTRODUCTION... 3 3 START-UP AND GENERAL

More information

1 Digital input (24Vac or dry contact) Inputs

1 Digital input (24Vac or dry contact) Inputs Fan oil Thermostat Fan oil Thermostat Features: Attractive modern look with large LD and backlight Icons driven information and 1 line of text information 2 Pipes Analog, ON/OFF or Floating 4 Pipes Analog,

More information

24HR/7 DAY YEARLY 4 CHANNEL INSTALLATION & OPERATING (4 MODULE) 16A. DIGITAL TIMESWITCH Cat. No TR644S INSTRUCTIONS

24HR/7 DAY YEARLY 4 CHANNEL INSTALLATION & OPERATING (4 MODULE) 16A. DIGITAL TIMESWITCH Cat. No TR644S INSTRUCTIONS 24HR/7 DAY YEARLY 4 CHANNEL (4 MODULE) 16A DIGITAL TIMESWITCH Cat. No TR644S INSTALLATION & OERATING INSTRUCTIONS 1.0 Description (page 64) 2.0 Features (page 64) 3.0 Application / Installation (page 65)

More information

! "! # $ % & ' ( ) " * % +, # # -. / ( ! " ! # $ % &

! ! # $ % & ' ( )  * % +, # # -. / ( !  ! # $ % & Manual HT55 2. General 2.1 Unpacking and inspecting The product must be inspected for possible shipping damage when it is unpacked. If damage is found then the freight carrier, railway company or postal

More information

TLC3-BCR-U Series Thermostat

TLC3-BCR-U Series Thermostat OVERVIEW TLC3-BCR-U Series Thermostat Features Low power energy consumption: < 1W per unit Relays switching for outputs each up to 300W Temperature control for 2 or 4-pipe heating or cooling systems. Optional

More information

RADIO DRIVER. * _Rev.1* Installation guide. Wireless programmer. RADIO DRIVER zone RADIO DRIVER zones

RADIO DRIVER. * _Rev.1* Installation guide. Wireless programmer. RADIO DRIVER zone RADIO DRIVER zones Installation guide RADIO DRIVER Wireless programmer 6051117 6051118 RADIO DRIVER 610-1 zone RADIO DRIVER 620-2 zones DELTA DORE - Bonnemain - 35270 COMBOURG - FRANCE E-mail: deltadore@deltadore.com 6051119

More information