LINETRAXX RCMB42. AC/DC sensitive residual current monitor for electric vehicle charging systems
|
|
- Steven Shepherd
- 5 years ago
- Views:
Transcription
1 IETRAXX RCMB42 AC/DC sensitive residual current monitor for electric vehicle charging systems RCMB42x_D00167_04_D_XXE/
2 IETRAXX RCMB42 AC/DC sensitive residual current monitor for electric vehicle charging systems Product description The AC/DC sensitive residual current monitoring module RCMB42 is used for fault current monitoring of AC charging stations for electric vehicles, in which DC or AC fault currents are likely to occur, the value of which is constantly greater than zero. IETRAXX RCMB420 IETRAXX RCMB422 unction Residual current monitoring of the charging station takes place via an externally connected measuring current transformer. Here, the r.m.s. value is determined by the DC component contained in the residual current and the AC component that is below the cut-off frequency. The alarm relays switch when the limit values I Δn 6 ma DC and/or r.m.s. value I Δn 30 ma (r.m.s.) are exceeded. After actuation of the device's own test button or via the digital input (e.g. with an external test button or a control device), the device generates a test current. The level of the test current is designed so that when functioning correctly the threshold is exceeded triggering both alarm relays. Before each charging process, the connected charge controller must check that the monitoring device functions correctly. The check focuses on safety-relevant residual current monitoring. Ensure that the charging process is disabled. The function increases the safety of the charging process and prevents long-term drift of the residual current measurement. The fault memory can be selected with the integrated sliding switch S1. Standards The IETRAXX RCMB42 series complies with the following device standard: IEC Device features DC sensor with additional AC tripping (type B characteristic) Response value 2 AC/DC 30 ma: r.m.s. value measurement Response value 1: DC 6 ma requency range residual current Hz requency range load current Hz Monitoring of the connection to the measuring current transformer ully shielded residual current transformer to avoid influences due to external disturbances Connection via push-wire terminals Variants: One-channel and two-channel residual current measurement 2 RCMB42x_D00167_04_D_XXE/
3 Ein wichtiges Zukunftsthema für die Automobilindustrie ist die Elektromobilität. Elektrofahrzeuge sollen künftig zunehmend dazu beitragen, die Erdölabhängigkeit zu verringern und die CO2-Belastung zu reduzieren. Mit der Messe ecartec und dem dazugehörigen Kongress wurde eine internationale Plattform ins eben gerufen, die sich ausschließlich mit dem Thema Elektromobilität beschäftigt. Vom 13. bis 15. Oktober präsentiert KEBA auf der ecartec erstmals in Deutschland die outdoorfähige Stromladestation KeContact, mit der alle Arten von elektrobetriebenen ahrzeugen, wie Autos, Motorroller, ahrräder, Segways oder Rollstühle einfach und sicher aufgeladen werden können und das rund um die Uhr. Quelle: 5-oktober-2009-halle-c3-messestand / Mastercard 22 T 12 T adekontrollregler adekontrollregler Ein wichtiges Zukunftsthema für die Automobilindustrie ist die Elektromobilität. Elektrofahrzeuge sollen künftig zunehmend dazu beitragen, die Erdölabhängigkeit zu verringern und die CO2-Belastung zu reduzieren. Mit der Messe ecartec und dem dazugehörigen Kongress wurde eine internationale Plattform ins eben gerufen, die sich ausschließlich mit dem Thema Elektromobilität beschäftigt. Vom 13. bis 15. Oktober präsentiert KEBA auf der ecartec erstmals in Deutschland die outdoorfähige Stromladestation KeContact, mit der alle Arten von elektrobetriebenen ahrzeugen, wie Autos, Motorroller, ahrräder, Segways oder Rollstühle einfach und sicher aufgeladen werden können und das rund um die Uhr. Quelle: 5-oktober-2009-halle-c3-messestand / A1 A2 Mastercard T AC/DC sensitive residual current monitor IETRAXX RCMB42 RCMB420 with 2 channels with I Δn 6 ma DC and I Δ = 30 ma (r.m.s.) each RCMB422 with 1 channel with I Δn 6 ma DC and I Δ = 30 ma (r.m.s.) each +1 OK +1 OK Un V A1/+ A2/- 13 Un 23 Test GD V = aderegler/charge controller A1/+ A2/- 13 Id2 23 Id2 Test GD = aderegler/charge controller RCMB42x_D00167_04_D_XXE/
4 AC/DC sensitive residual current monitor IETRAXX RCMB42 Technical data Insulation coordination according to IEC Definitions Supply circuit (IC1) A1, A2 Measuring circuit (IC2), Id2, Test, GD Output circuit 1 (IC3) 13, Output circuit 2 (IC4) 23, Monitored current circuit (IC5) Un Rated voltage Overvoltage category (OVC) III Pollution degree 2 RCMB42-25 Rated insulation voltage IC1/IC2 (IC1-IC2)/(IC3-IC5) IC3/(IC4-IC5) Rated impulse voltage IC1/IC2 (IC1-IC2)/(IC3-IC5) IC3/(IC4-IC5) Safe isolation (reinforced insulation) between (IC1-IC2)/(IC3-IC5) (IC3-IC4)-IC5 Basic insulation between IC3/IC4 unctional insulation between IC1/IC2 Voltage tests (routine test) acc. to IEC (IC1-IC2)/(IC3-IC4) IC2-IC5 IC3/IC4 RCMB42-2 Rated insulation voltage IC2/(IC3-IC5) IC3/IC4-IC5 Rated impulse voltage IC2/(IC3-IC5) IC3/IC4-IC5 Safe isolation (reinforced insulation) between IC2-(IC3-IC5) IC3-(IC4-IC5) (IC3-IC4)-IC5 Basic insulation between IC3/IC4 Voltage tests (routine test) acc. to IEC IC2/(IC3-IC5) IC2/(IC3-IC4) IC4-IC5 40 V 800 V OVC III, OVC III, OVC III, DC 1 kv 60 s OVC III, OVC III, OVC III, OVC III, OVC III, Supply voltage RCMB42-25 ominal voltage U S ominal voltage range U S ominal current Internal protection against reverse polarity and short circuit RCMB42-2 ominal voltage range U S DC V DC V 110 ma (RCMB420-25) 70 ma (RCMB422-25) AC V, 50/60 Hz DC V Tolerance of the nominal voltage range of U S % ominal current 30 ma Residual current measuring range Rated frequency Measuring range Response values Hz ±300 ma Residual current I Δn1 6 ma Response tolerance I Δn % Residual current I Δn2 30 ma (r.m.s.) Response tolerance I Δn2 for f 1 khz % for f > 1 khz % Restart sequence value DC 6 ma < 3 ma AC/DC 30 ma (r.m.s.) for f 1 khz < 12 ma AC/DC 30 ma (r.m.s.) for f > 1 khz < 22 ma Operating time t ae1 for 1 x I Δn1 < 600 ms Operating time t ae2 for 1 x I Δn2 < 180 ms 2 x I Δn2 < 70 ms 5 x I Δn2 < 20 ms Inputs and operation Test button Test Cable length Test/, GD Transformer connection ED device function ED alarm channel 1 ED alarm channel 2 Output Common alarm signal o error or Switching elements on front side internal/external < 10 m external green yellow yellow Open-Collector (npn) V V Alarm relays K1, K2 I Δn 6 ma DC; I Δn 30 ma r.m.s. Switching elements 2 x 1 /O contacts Operating principle /C operation Electrical endurance, number of cycles 10,000 Contact data according to IEC Utilisation category Rated operational voltage U e Rated operational current I e Minimum contact rating AC-/DC-13 5 A 1 ma at AC/DC 10 V 4 RCMB42x_D00167_04_D_XXE/
5 AC/DC sensitive residual current monitor IETRAXX RCMB42 Environment/EMC EMC IEC , IEC Operating temperature C Classification of climatic conditions acc. to IEC Stationary use (IEC ) 3K5 (except condensation and formation of ice) Transport (IEC ) 2K2 ong-term storage (IEC ) 1K2 Classification of mechanical conditions acc. to IEC Stationary use (IEC ) Transport (IEC ) ong-term storage (IEC ) Connection Connection type Connection properties Rigid lexible without ferrules lexible with ferrules Stripping length Opening force Test opening, diameter 3M4 2M2 1M3 push-wire terminals mm² (AWG ) mm² (AWG 19 ) mm² (AWG 16) 10 mm mm Other Operating mode continuous operation Degree of protection, internal components IP 30 Degree of protection, terminals IP 20 Area of application 2000 m AMS Quick DI rail mounting acc. to IEC Screw mounting 2 x M4 with mounting clip Measuring current transformer Diameter cable gland measuring current transformer 15 mm Cable length 1.5 m Max. cable cross section 4 x 6 mm 2 Mounting with cable ties Connection to RCMB42 plug-in connector with 6 poles Rated voltage U n 3/() AC 400/230 V Rated current I n 3x32 A Rated impulse withstand voltage U imp Ordering details umber of measuring Measuring range requency Supply voltage U S current transformers Channels Type Art. o. range DC r.m.s. (Ø 15 mm, 1.5 m cable) AC DC V, 50/60 Hz V RCMB420-2 B x residual current V RCMB B ma 0 30 ma Hz V, 50/60 Hz V RCMB422-2 B x residual current V RCMB B Delivery incl. measuring current transformers. Measuring current transformers available with shorter cable on request (minimum order quantity 250 pcs.) Accessories Description Mounting clip for screw mounting (1 piece per device) Art. o. B Dimension diagram XM420 Dimensions in mm (tolerance acc. to ISO m) Screw mounting ote: The upper mounting clip must be ordered separately (see accessories). 115 mm mm RCMB42x_D00167_04_D_XXE/
6 Bender GmbH & Co. KG P.O. Box Grünberg Germany ondorfer Straße Grünberg Germany Tel.: ax: BEDER Group RCMB42x_D00167_04_D_XXE / / pdf / Bender GmbH & Co. KG, Germany Subject to change! The specified standards take into account the edition valid until unless otherwise indicated.
LINETRAXX VMD460-NA. Network and system protection (NS protection) for monitoring the power feed-in of power generation systems
LIETRAXX -A etwork and system protection (S protection) for monitoring the power feed-in of power generation systems -A_D00001_01_D_XXE/09.2015 LIETRAXX -A etwork and system protection (S protection) for
More informationMeasuring current transformers of the W AB(P) series
Measuring current transformers of the W AB(P) series W-AB(P)_D00074_02_D_XXEN/07.2017 Measuring current transformers of the W AB(P) series Product description Measuring current transformers of the W -AB
More informationPEM353. Universal measuring device
353 Universal measuring device 353_D00335_00_D_XXEN/06.2018 353 Universal measuring device Product description The digital universal measuring device 353 is used to record and display measured quantities
More informationMeasuring current transformers of the W B series
Measuring current transformers of the W B series W-B_D00075_01_D_XXEN/09.2015 Measuring current transformers of the W B series Product description Measuring current transformers of the W B series are highly
More informationMeasuring current transformers of the W, W series
Measuring current transformers of the W, W -8000 series W(-8000)_D00078_01_D_XXEN/09.2015 Measuring current transformers of the W, W -8000 series Product description The highly sensitive W and W -8000
More informationAC/DC sensitive residual current monitoring module RCMB121-
AC/DC sensitive residual current monitoring module RCMB121- for safe charging of electrical vehicles according to IEC 62752 for IC-CPD and IEC 60364-7-722 for Wall Boxes Vorläufiges Datenblatt RCMB121_D00267_01_D_XXEN/05.2018
More informationPortable equipment for insulation fault location for unearthed and earthed systems (IT and TN systems) to be used in conjunction with or without an
EDS309 Portable equipment for insulation fault location for unearthed and earthed systems (IT and TN systems) to be used in conjunction with or without an equipment for insulation fault location EDS309x_D00012_00_D_XXEN/05.2015
More informationPortable equipment for insulation fault location for unearthed and earthed systems (IT and TN systems) to be used in conjunction with or without an
EDS309 Portable equipment for insulation fault location for unearthed and earthed systems (IT and TN systems) to be used in conjunction with or without an equipment for insulation fault location EDS309x_D00012_02_D_XXEN/11.2018
More informationISOSCAN EDS460-DG. Insulation fault locator for DC IT systems with high system leakage capacitances
ISOSCAN Insulation fault locator for DC IT systems with high system leakage capacitances _D00108_00_D_XXEN/05.2015 ISOSCAN Insulation fault locator for DC IT systems with high system leakage capacitances
More informationISOMETER iso685- -B. Insulation monitoring device for unearthed AC, AC/DC and DC systems (IT systems) Preliminary data sheet
Insulation monitoring device for unearthed AC, AC/DC and DC systems (IT systems) Preliminary data sheet iso685-x-b_d00177_04_d_xxen/04.2018 Insulation monitoring device for unearthed AC, AC/DC and DC systems
More informationAC/DC sensitive residual current monitoring module RCMB121-
AC/DC sensitive residual current monitoring module RCMB121- for safe charging of electrical vehicles according to IEC 62752 for IC-CPD and IEC 60364-7-722 for Wall Boxes Preliminary datasheet Vorläufiges
More informationISOMETER iso685- Insulation monitoring device for unearthed AC, AC/DC and DC systems (IT systems)
Insulation monitoring device for unearthed AC, AC/DC and DC systems (IT systems) iso685-x_d00022_08_d_xxen/04.2018 Insulation monitoring device for unearthed AC, AC/DC and DC systems (IT systems) Product
More informationDipl.-Ing. W. Bender GmbH & Co. KG Londorfer Str Grünberg Tel.: Fax:
Dipl.-Ing. W. Bender GmbH & Co. KG Londorfer Str. 65 35305 Grünberg Tel.: 06401 807-0 Fax: 06401 807-259 Insulation fault locator Insulation fault locator for DC IT systems with high system leakage capacitances
More informationISOMETER IRDH575. Approvals
Insulation monitoring device for unearthed AC, DC and AC/DC systems (IT systems) with control and display function for EDS insulation fault location systems IRDH575_D00089_02_D_XXEN/09.2018 Insulation
More informationPower Quality and Energy Measurement PEM735
Power Quality and Energy Measurement PEM75 PEM75_D00084_01_D_XXEN/01.2015 Power Quality and Energy Measurement PEM75 class A Product description The digital universal measuring device PEM75 is suited for
More informationElectronic timer CT-ERS ON-delayed with 2 c/o contacts Data sheet
1SVR 430 103 F0200 CT-ERS 1 7 2 6 5 4 8 3 1 10 selectable time ranges, from 0.05 s to 300 h 2 Potentiometer with direct reading scale for the fine adjustment of the time delay 3 Sliding switch to set the
More informationRCMS460 and RCMS490 Series
4 T M RCMS460 and RCMS490 Series Digital Multi-Channel Ground Fault Monitor / Ground Fault Relay Grounded and High-Resistance Grounded AC/DC Systems Technical Bulletin NAE1042060 / 04.2013 BENDER Inc.
More informationPower Quality and Energy Measurement PEM533
Power Quality and Energy Measurement _D00013_02_D_XXEN/11.2014 Power Quality and Energy Measurement 0.5 S Product description The digital universal measuring device is suited for measuring and displaying
More informationThree-phase monitoring relay CM-PFS
Data sheet Three-phase monitoring relay CM-PFS The CM-PFS is a three-phase monitoring relay that is used to monitor three phase mains for incorrect phase sequence and phase failure. All devices are available
More informationISOMETER iso685-d-p. Device features
ISOMETER iso6- -P Insulation monitoring device with integrated locating current injector for IT AC systems with galvanically connected rectifiers or converters and for IT DC systems iso6-x-p_d D_XXEN/.
More informationPower Quality and Energy Measurement PEM575
Power Quality and Energy Measurement _D00016_03_D_XXEN/12.2015 Power Quality and Energy Measurement Product description The digital universal measuring device is suited for measuring and displaying electrical
More informationCoupling unit CM-IVN For expansion of the insulation monitoring relay CM-IWN.x measuring range up to U n = 690 V AC and 1000 V DC
Data sheet Coupling unit CM-IVN For expansion of the insulation monitoring relay CM-IWN.x measuring range up to U n = 690 V AC and 1000 V DC The CM-IVN serves to extend the measuring range of the insulation
More informationV2UM230V10 Art.Nr.: V2UM230V10P Art.Nr.: Control elements. Tripping delay. Function selector. Status indication 230 V AC/DC
P AC/DC voltage monitoring Multifunction Supply voltage 24 V DC or 230V AC/DC Supply circuit = Measuring circuit 1 change-over contact Width 22,5 mm Control elements Tripping delay Maximum threshold Minimum
More informationLiquid level monitoring relay CM-ENS.2x
Data sheet Liquid level monitoring relay CM-ENS.2x The CM-ENS.2x is served to regulate and control liquid levels and ratios of mixtures of conductive fluids. It can be used for overflow protection, dry
More informationControl module CP-A CM
Control module 2CDC 271 002 F0t05 Features Pluggable onto redundancy unit CP-A RU Adjustable threshold values (14-28 V) and relay outputs per input / channel Approvals Marks g 6 7 1 3 4 2 8 5 Order data
More informationElectronic timer CT-AWS Impulse-OFF with 1 c/o contact Data sheet
2CDC 251 121 F0004 1 5 2 4 3 6 Characteristics Single-function impulse-off timer One device includes 10 time ranges, from 0.05 s to 300 h, for the adjustment of the pulse time Remote potentiometer connection
More informationType CP-S, CP-C & CP-A Switch mode
Switch mode power CP-S, CP-C & CP-A Switch mode Characteristics CP-S and CP-C range Output current 5 A, 10 A and 20 A Integrated power reserve of up to 50 % 5 A and 10 A devices with pluggable connecting
More informationTemperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection)
Data sheet Temperature monitoring relays CM-TCS Monitoring relays for monitoring temperatures with a PT100 sensor (2- or 3-wire connection) The temperature monitoring relays CM-TCS monitor overtemperature,
More informationCoupling unit CM-IVN For expansion of the insulation monitoring relay CM-IWN.x measuring range up to U n = 690 V AC and 1000 V DC
Data sheet Coupling unit CM-IVN For expansion of the insulation monitoring relay CM-IWN.x measuring range up to U n = 690 V AC and 1000 V DC The CM-IVN serves to extend the measuring range of the insulation
More informationVEO. V2PF480Y/277VSY01 Art.Nr.: V2PF480Y/277VSY01P Art.Nr.: TECHNICAL DATA
P Monitoring of phase sequence and phase loss Monitoring of asymmetry Supply voltage 208-480 V AC Supply circuit = measuring circuit 1 change-over contact Width 22,5 mm Control elements Asymmetry Status
More informationInstallation- / Monitoring technique
Installation- / Monitoring technique ifferential current monitor IP 5883, Type B for AC and C systems varimeter 0249633 IP 5883 N 5018/035 N 5018/030 According to IEC/EN 62 020, VE 0663 To detect earth
More informationCurrent / residual current and voltage transformers. Current / residual current and voltage transformers
Current / residual current and voltage transformers Current / residual current and voltage transformers 1 Overview Current transformer overview DIN rail current transformer with fuse Current transformer...
More informationVEO. V2PF480Y/277VS01 Art.Nr.: B TECHNICAL DATA
Monitoring of phase sequence and phase loss Monitoring of asymmetry Supply voltage 208-480 V AC Supply circuit = measuring circuit 1 change-over contact Width 22,5 mm Status indication LED U: Supply voltage
More information* Short-circuit detection at On pushbutton. Applications. Indication. S M6801_a S11 A3 S12 S21 S23 S22 S (+)
Safety technique Emergency stop module BO 5988 safemaster 0221562 Function diagram Pushbutton on Mains or emergencystop () K1 According to EC Directive for machines 98/37/EG According to IEC/E 60204-1
More informationAC/DC. Monitoring Technique. VARIMETER IMD Insulation monitor RN 5897/300
Monitoring Technique VARIMETER IMD Insulation monitor RN 5897/300 0274214 Your Advantages For mobile generator sets according to DIN VDE 0100-551 Preventive fire and system protection Detection of symmetric
More informationSafety Technique. Emergency Stop Module With Time Delay BH 5928, BI 5928
Safety Technique safemaster Emergency Stop Module With Time Delay BH 5928, BI 5928 0226419 BH 5928 BI 5928 Function Diagram According to - Performance Level (PL) e and category 4 to E ISO 13849-1 2008
More informationThermistor motor protection relays
Thermistor motor protection relays Content Benefits and advantages... / 68 Selection table... / 68 Ordering details CM-MSE... / 69 CM-MSS... / 69 CM-MSN... / 7 PTC sensor C0... / 7 Technical data... /
More information27/04/2015
Modular Carril DIN 35 mm HIL Part number 84871120 Control of AC and DC currents Automatic recognition of AC/DC Measurement ranges from 2 ma to 10 A Choice between over and undercurrent True RMS measurement
More informationInsulation monitoring relay CM-IWS.1 For unearthed AC, DC and mixed AC/DC systems up to U n = 250 V AC and 300 V DC
Data sheet Insulation monitoring relay CM-IWS.1 For unearthed AC, DC and mixed AC/DC systems up to U n = 250 V AC and 300 V DC The CM-IWS.1 serves to monitor insulation resistance in accordance with IEC
More informationThree-phase monitoring relays CM-PVS CM-PVS.31, CM-PVS.41 and CM-PVS.81
Data sheet Three-phase monitoring relays CM-PVS CM-PVS.31, CM-PVS.41 and CM-PVS.81 The three-phase monitoring relays CM-PVS.x1 monitor the phase parameters phase sequence, phase failure as well as over-
More informationControl module CP-A CM
2CDC 271 002 F0t05 Features Pluggable onto redundancy unit CP A RU Threshold values adjustable (14 28 V) One relay output per monitored input / channel Approvals H UL 508, CAN/CSA C22.2 No.14 H UL 60950,
More informationSafety Technique. SAFEMASTER Emergency Stop Module With Time Delay BH 5928, BI 5928
Safety Technique SAFEMASTER Emergency Stop Module With Time Delay BH 5928, BI 5928 0226419 BH 5928 BI 5928 Function Diagram According to - Performance Level (PL) e and category 4 to E ISO 13849-1 2008
More informationThree-phase monitoring relays CM-PVS.81
Data sheet Three-phase monitoring relays CM-PVS.81 The three-phase monitoring relay CM-PVS.81 monitors the phase parameters phase sequence, phase failure as well as over- and undervoltage. The device is
More informationThree-phase monitoring relays CM-PSS CM-PSS.31 and CM-PSS.41
Data sheet Three-phase monitoring relays CM-PSS CM-PSS.31 and CM-PSS.41 The three-phase monitoring relays CM-PSS.x1 monitor the phase parameters phase sequence, phase failure as well as over- and undervoltage.
More informationV2IM10AL10 Art.Nr.: V2IM10AL10P Art.Nr.: Control element. Tripping delay. Function selector. Status indication 24...
P AC/DC current monitoring Multifunction Supply voltage 24-240V DC or 110-240V AC 1 change-over contact Width 22,5 mm Control element Tripping delay Maximum threshold Minimum threshold Function selector
More informationisolr275 / AGH-LR Digital Ground Fault Monitor / Ground Detector For Low-Resistance Ungrounded (Floating) AC/DC Systems
T M 1 isolr275 / AGH-LR Digital Ground Fault Monitor / Ground Detector For Low-Resistance Ungrounded (Floating) AC/DC Systems Technical Bulletin NAE1012110 / 12.2011 isolr275 / AGH-LR Ground Fault Monitor
More informationVoltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.2 For single-phase AC/DC voltages The CM-ESS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
More informationThree-phase monitoring relays CM-PFE and CM-PFE.2
Data sheet Three-phase monitoring relays CM-PFE and CM-PFE.2 The CM-PFE is a three-phase monitoring relay that monitors the phase parameter phase sequence and phase failure in three-phase mains. 2CDC 251
More informationInstallation / Monitoring Technique
Installation / Monitoring Technique VARIMETER RCM Residual Current Monitor, Type B for AC and DC Systems IP 5883 0249633 IP 5883 ND 5018/035 ND 5018/030 According to IEC/EN 62 020, VDE 0663 For AC and
More informationMultifunctional three-phase monitoring relays CM-MPN CM-MPN.52, CM-MPN.62 and CM-MPN.72
Data sheet Multifunctional three-phase monitoring relays CM-MPN CM-MPN.52, CM-MPN.62 and CM-MPN.72 The three-phase monitoring relays CM-MPN.x2 monitor the phase parameters phase sequence, phase failure,
More informationABB 1. Multifunctional three-phase monitoring relays. CM-MPN.52, CM-MPN.62 and CM-MPN.72 Data sheet. Features. Approvals. Marks.
2CDC 251 054 F0t08 CM-MPN.52 2CDC 251 055 F0t08 CM-MPN.62 2CDC 251 056 F0t08 CM-MPN.72 Features Monitoring of three-phase mains for phase sequence (can be switched off), phase failure, over- and undervoltage
More informationCurrent monitoring relays CM-SRS.2 For single-phase AC/DC currents
Data sheet Current monitoring relays CM-SRS.2 For single-phase AC/DC currents The CM-SRS.2 is an electronic current monitoring relay that protects single-phase mains (DC or AC) from over- and undercurrent
More informationThermistor motor protection relays
Thermistor motor protection relays Content Benefits and advantages... / 68 Selection table... / 68 Ordering details CM-MSE... / 69 CM-MSS... / 69 CM-MSN... / 7 PTC sensor C0... / 7 Technical data... /
More informationThree-phase monitoring relay
1SR 430 824 F9300 Features Monitoring of three-phase mains for phase sequence and failure Powered by the measuring circuit 2 c/o (SPDT) contacts 1 LED for status indication Approvals R: yellow LED - relay
More informationPower Quality and Energy Measurement PEM575
Power Quality and Energy Measurement _D00016_00_D_XXEN/06.2013 Power Quality and Energy Measurement Product description The digital universal measuring device is suited for measuring and displaying electrical
More informationThree-phase monitoring relays
2CDC 251 046 F0t08 Features Monitoring of three-phase mains for phase sequence, phase failure, phase unbalance Threshold value for phase unbalance adjustable as absolute value Tripping delay can be adjusted
More informationABB NEW. Three-phase monitoring relays. CM-PVS.31 and CM-PVS.41 Data sheet. Features J. Approvals. Marks. Order data. Order data - Accessories
2CDC 251 042 F0t08 CM-PVS.31 Features Monitoring of three-phase mains for phase sequence (can be switched off), phase failure, over- and undervoltage Threshold values for over- and undervoltage are adjustable
More informationVoltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages
Data sheet Voltage monitoring relay CM-EFS.2 For single-phase AC/DC voltages The CM-EFS.2 is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
More informationPD30CNB25xxPS. Photoelectrics, Background suppression reflective - PointSpot. Main features. Main functions. Description
Photoelectrics, Background suppression reflective - PointSpot Main features Miniature sensor range The visible red PointSpot light makes alignment very easy Range: 250 mm Sensitivity adjustment by potentiometer
More informationMeasuring and monitoring relays CM-SRS.1 Current monitoring relays, single-phase AC/DC
2CDC 251 244 F0t05 Characteristics Monitoring of DC and AC currents: RMS measuring principle One device includes 3 measuring ranges Over- or undercurrent monitoring configurable Hysteresis adjustable from
More information2 Pole CO, 8 A Plug-in 2 CO (DPDT) 1 CO (SPDT) 8/15 16/25* 250/ /400 2,000 4, /0.5/ /0.5/ (5/5) 300 (10/5)
46 Series - Relays for railway applications 8-16 A 46 SERIES Features Plug-in power relays: 8 A, 2 pole 16 A, 1 pole Complies with EN 45545-2:2013 (protection against fire of materials), EN 61373 (resistance
More informationCurrent monitoring relays CM-SRS.1 For single-phase AC/DC currents
Data sheet Current monitoring relays CM-SRS.1 For single-phase AC/DC currents The CM-SRS.1 is an electronic current monitoring relay that protects single-phase mains (DC or AC) from over- and undercurrent
More informationMultifunctional three-phase monitoring relays CM-MPS CM-MPS.23 and CM-MPS.43
Data sheet Multifunctional three-phase monitoring relays CM-MPS CM-MPS.23 and CM-MPS.43 The three-phase monitoring relays CM-MPS.x3 monitor the phase parameters phase sequence, phase failure, over- and
More informationInsulation monitoring relay CM-IWS.2 For unearthed AC systems up to U n = 400 V AC
Data sheet Insulation monitoring relay CM-IWS.2 For unearthed AC systems up to U n = 400 AC The CM-IWS.2 serves to monitor insulation resistance in accordance with IEC 61557-8 in unearthed IT AC systems
More informationMeasuring current transformer for universal measuring devices
Measuring transformer for universal measuring devices Measuring--transformer-PQ_D0023_0_D_XXN/06.208 Measuring transformer for universal measuring devices Product description All measuring devices of the
More informationType Nominal voltage (V) Code HSV V
Speed control Speed control relay - mm Control of overspeed, underspeed, operating rate, stopping Measurement via discrete sensors - -wire PNP or NPN, Namur, voltage 0-0V or volt-free contact type Works
More informationPhase control Single function phase control relay - 7.5 mm Control of -phase networks: phase sequence, total phase failure Multi-voltage from x 08 to x 480 V Controls its own supply voltage True RMS measurement
More informationMultifunctional three-phase monitoring relays CM-MPS CM-MPS.23
Data sheet Multifunctional three-phase monitoring relays CM-MPS CM-MPS.23 The three-phase monitoring relay CM-MPS.23 monitors the phase parameters phase sequence, phase failure, over- and undervoltage
More informationABB NEW. Multifunctional three-phase monitoring relays. CM-MPS.23 and CM-MPS.43 Data sheet. Features J. Approvals. Marks.
2CDC 251 052 F0t08 CM-MPS.23 2CDC 251 053 F0t08 CM-MPS.43 - relay status, timing - fault message - fault message Adjustment of the tripping delay t V Adjustment of the threshold value for overvoltage 6
More informationLED Driver Compact fixed output
Driver C 5W 35-6mA flexc SC advanced series Product description Can be either used build-in or independent with clip-on strain-relief (see accessory) Constant current Adjustable output current between
More informationCM-MPS.11, CM-MPS-21, CM-MPS.31 and CM-MPS.41 Data sheet. UL 508, CAN/CSA C22.2 No.14 GL GOST CB scheme CCC
2CDC 251 048 F0t08 CM-MPS.11 2CDC 251 049 F0t08 CM-MPS.21 Features Monitoring of three-phase mains for phase sequence (can be switched off), phase failure, over- and undervoltage as well as phase unbalance
More informationPower Quality and Energy Measurement PEM330/PEM333
Power Quality and Energy Measurement PEM330/PEM333 TDB310001en / 02.2013 Power Quality and Energy Measurement PEM330/PEM333 0.5S Product description The universal measuring device PEM330/333 is used to
More informationMINI-PS AC/2X15DC/1
MII-PS-100-240AC/2X15DC/1 Power supply unit ITERFACE Data sheet 100299_en_04 1 Description PHOEIX COTACT - 2010-10-20 Features MII POWER is the extremely slim power supply unit with constructional widths
More informationABB 1. Multifunctional three-phase monitoring relays. CM-MPS.11, CM-MPS-21, CM-MPS.31 and CM-MPS.41 Data sheet. Features. Approvals. Marks.
2CDC 251 048 F0t08 CM-MPS.11 2CDC 251 049 F0t08 CM-MPS.21 2CDC 251 050 F0t08 CM-MPS.31 2CDC 251 051 F0t08 CM-MPS.41 R/T: yellow LED - relay status, timing F1: red LED - fault message F2: red LED - fault
More informationPower Electronics. POWERSWITCH Solid-State Contactor BF 9250, BH 9250
Power Electronics POWERSWITCH Solid-State Contactor, BH 9250 02342 According to IEC/E 60 947-4-2, IEC/E 60 947-4-3 1-, 2- and 3-pole models Load current up to 50 A For AC load up to 480 V Switching at
More informationVoltage monitoring relays CM-ESS.M For single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.M For single-phase AC/DC voltages The CM-ESS.M is an electronic voltage monitoring relay that provides reliable monitoring of voltages as well as detection of
More informationElectronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts
Data sheet Electronic timer CT-AHS.22 OFF-delayed with 2 c/o (SPDT) contacts The CT-AHS.22 is an electronic timer from the CT-S range with OFF-delay and 10 time ranges. All electronic timers from the CT-S
More informationThree-phase monitoring relay CM-PBE
Data sheet Three-phase monitoring relay CM-PBE The three-phase monitoring relay CM-PBE monitors the phase parameter phase failure in three-phase mains. 2CDC 251 007 S0012 Characteristics Monitoring of
More informationPHOENIX CONTACT
Electronic circuit breaker CLIPLINE Data sheet 102898_en_03 PHOENIX CONTACT 2010-12-17 1 Description The electronic circuit breaker can be used in applications that cover all aspects of the switched-mode
More informationElectronic timer CT-MXS.22 Multifunctional with 2 c/o (SPDT) contacts
Data sheet Electronic timer CT-MXS.22 Multifunctional with 2 c/o (SPDT) contacts The CT-MXS.22 is a multifunctional electronic timer from the CT-S range. It provides 5 timing functions, 2 times 10 time
More informationPower Electronics. POWERSWITCH Semiconductor Contactor BF 9250, BH 9250
Power Electronics POWERSWITCH Semiconductor Contactor, BH 9250 02342 According to IEC/E 60 947-4-2, IEC/E 60 947-4-3 1-, 2- and 3-pole models Load current up to 50 A For AC load up to 480 V Switching at
More informationElectronic timer CT-TGD.22
2CDC 251 097 F0t06 a Rotary switch for the preselection of the time range of the ON time b Potentiometer with direct reading scale for the fine adjustment of the ON time c Rotary switch for the preselection
More informationAnalog signal converters CC-E I/I
2CC 281 001 F0b06 Features Loop-powered I/I isolator without external power supply for analog current signals of 0-20 ma and 4-20 ma Electrical isolation between input and output Very low internal voltage
More informationISOMETER IR Headline. Version V004. Vorläufiges Datenblatt
Headline ISOMETER IR155-4210 Sub-Headline Insulation monitoring device (IMD) for unearthed charging systems (IT systems), for e.g. electric vehicles Version V004 Vorläufiges Datenblatt TDB106035en / 06.2012
More informationCurrent monitoring relays CM-SRS.2 for single-phase AC/DC currents
Data sheet Current monitoring relays CM-SRS.2 for single-phase AC/DC currents For the monitoring of currents in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact
More informationCurrent monitoring relays CM-SRS.M1 For single-phase AC/DC currents
Data sheet Current monitoring relays CM-SRS.M1 For single-phase AC/DC currents The CM-SRS.M1 is an electronic current monitoring relay that monitors single-phase mains (DC or AC) for over- and undercurrent
More informationElectronic timer CT-MFS.21
2CDC 251 053 F0t07 a Rotary switch for the preselection of the time range b Potentiometer with direct reading scale for the fine adjustment of the time delay c Rotary switch for the preselection of the
More informationLED Driver Linear / area fixed output
Driver LC 53W 5-35mA flexc lp ANCED series Product description Built-in constant current LED Driver New version DC operating with EL marking Adjustable output current between 5 and 35 ma Max. output power
More informationLED Driver Compact fixed output
Driver C 6W -4mA flexc SC ADV ADVACED series Product description Can be either used build-in or independent with clip-on strain-relief (see accessory) Constant current ED Driver Adjustable output current
More informationVoltage monitoring relays CM-ESS.1 for single-phase AC/DC voltages
Data sheet Voltage monitoring relays CM-ESS.1 for single-phase AC/DC voltages For the monitoring of voltages in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact
More information60 Series - General purpose relays 6-10 A. Features Plug-in mount 10 A General purpose relay
Series - General purpose relays - 0 A Features Plug-in mount 0 A General purpose relay.. & pole changeover contacts Cadmium Free contacts (preferred version) AC coils & DC coils UL Listed (certain relay/socket
More informationMonitoring Relays True RMS 3-Phase, 3-Phase+N, Multifunction Types DPC01, PPC01
Monitoring Relays True RMS 3-Phase, 3-Phase+, Multifunction Types DPC01 Product Description 3-phase or 3-phase+neutral line voltage monitoring relay for phase sequence, phase loss, asymmetry, over and
More informationMoeller Electric Corporation
EMR4-I Current Monitoring Relays 02/0053 EMR4-I1-2-A EMR4-I15-2-A EMR4-I15-2-B Mechanical lifespan operations x10 6 30 30 30 24-h cycle, 55 C, 93 % relative humidty, 96 h Ambient temperature min./max.
More informationLED Driver Constant voltage
Driver LCU 100/96W 12/24V IP20 EXC EXCITE indoor IP20 series Product description LED Driver Universal input voltage range Constant output voltage Push terminals for simple wiring Nominal life-time up to
More informationElectronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts
Data sheet Electronic timer CT-MVS.23 Multifunctional with 2 c/o (SPDT) contacts The CT-MVS.23 is a multifunctional electronic timer from the CT-S range. It provides 11 timing functions and 10 time ranges.
More informationElectronic timer CT-SDE
CDC 51 059 F000 1 Characteristics " 1 single time range from 0. to 0 s " versions with different supply voltage ranges are available: 4 AC/DC and 110-10 AC and 80-415 AC " Single-function timer with star-delta
More informationAC/DC. Monitoring Technique. VARIMETER IMD Insulation monitor RN 5897/020
Monitoring Technique VARIMETER IMD Insulation monitor RN 5897/020 0277078 RN 5897/020 RP 5898 Product Description The insulation monitor RN 5897/020 of the VARIMETER IMD family provides best and up to
More informationCurrent monitoring relays CM-SRS.1 for single-phase AC/DC currents
Data sheet Current monitoring relays CM-SRS.1 for single-phase AC/DC currents For the monitoring of currents in single-phase AC/DC systems, ABB s CM range comprises a wide selection of powerful and compact
More informationPD30ETB20xxIS. Photoelectrics, Background Suppression reflective with IR light. Main features. Description
Photoelectrics, Background Suppression reflective with IR light Main features Description The PD30ET... stainless steel sensors are built with high-quality materials and designed for harsh environments.
More informationIMPULSE SWITCH, REMOTE SWITCH
W REMOTE SWITCH STELLA W SCHRACK INFO Low switching noise Energy saving function 0.5 30 minutes High switching capacity, 80 A start-up peak LED display LQ540000 W APPLICATIONS 220 The ideal solution for
More information