Electronic Instrumentation & Automation. ET-7th semester. By : Rahul Sharma ET & TC Deptt. RCET, Bhilai

Size: px
Start display at page:

Download "Electronic Instrumentation & Automation. ET-7th semester. By : Rahul Sharma ET & TC Deptt. RCET, Bhilai"

Transcription

1 Electronic Instrumentation & Automation ET-7th semester By : Rahul Sharma ET & TC Deptt. RCET, Bhilai

2 UNIT: III Voltage and Current Measurements Digital Voltmeters: Non-Integrating type, Integrating Type, Using counting circuits. Detectors: Principles of AC voltage measurement, Average and Peak responding detectors, Peak to Peak detector, Root mean square detectors, DC and AC probes. Multimeters: Basic Hand-held Multimeter, Bench type Digital Multimeters, Comparison of Analog and Digital Multimeters, Digital LCR meters.

3 Digital Voltmeters It displays the value of voltage, AC or DC, being measured in digital number system. It eliminates observational errors like parallax or approximations completely. It provides output with a better speed and also fed it directly to memory devices for storage.

4 ADC Signal Processing Data Transmission Element Reference Display

5 Classification of DVM Non Integrating Type Ramp Type Voltmeter Potentiometric Type Voltmeter Successive Approximation Type Voltmeter Integrating Type Voltage to Frequency Conversion Type Voltmeter Dual Slope or Voltage to Time Conversion Type Voltmeter

6 Ramp Type Voltmeter Linear Ramp Type Voltmeter

7

8 Its principle is to measure the time that a linear ramp voltage takes from level of input voltage to zero voltage. The time interval is measured in terms of counts, which is displayed as a number of digits. A Sample Rate Multivibrator is used for initiating pulse for ramp voltage.

9 Advantages of Linear Ramp Type Voltmeter It has easy circuit design. The cost is low. Output pulse can be transferred over long lines without data loss. Input signal is converted to time which is easy to digitize.

10 Disadvantages of Linear Ramp Type Voltmeter The accuracy depends only on ramp. Large errors are possible, if noise is superimposed with input. The speed of measurement is low.

11 Staircase Ramp Type Voltmeter Start Stop Gate Open Gate Closed

12 Comparator DAC Ref. Voltage Clock Counter Reset/Start Display

13 It compares the input signal with internally generated staircase ramp voltage which increases starting from zero. The total number of staircase is counted and displayed as the output. The step height of staircase voltage can be varied by appropriate reference voltage.

14 Advantages & Disadvantages of Staircase Ramp Type Voltmeter Advantages: Comparatively greater accuracy. Circuit is simple & of low cost. Input impedance of DAC is high when compensation is reached. Disadvantages: Accuracy depends only on DAC. Speed is limited up to 10 readings per seconds.

15 Potentiometric Type Voltmeter Error Signal Error Amplifier Potentiometer Adj. Device Readout Input Voltage Comparator Feedback Voltage Sliding Contact Ref. Voltage

16 Successive Approximation Type Voltmeter Unknown Voltage High Low DAC Reference Logic Control & Sequencer Digital Display

17 Advantages & Disadvantages of Successive Approximation Type Voltmeter Advantages: Accuracy is very high. High speed of 100 readings per second is possible. Display up to 5 digits is possible. Disadvantages: Circuitry is complex. Input impedance is variable. Comparator can make errors if noise is introduced.

18 Integrating Type DVM Voltage to Frequency Conversion:

19

20 It measures the average value of the input voltage over a fixed measuring period. It employs the voltage to frequency conversion as an integration technique. For any input voltage, the integrator produces a ramp voltage of opposite polarity.

21 Dual Slope Type DVM:

22

23 Advantages of Dual Slope Type DVM Excellent noise reduction. RC time constant not affect the input measurement. Integrator response to average value, so no sample & hold circuit is required. Accuracy is high & can be varied by requirement.

24 Principles of AC Voltage Measurement AC voltmeters are classified as: Average responding. Peak responding. RMS responding. Average & peak responding voltmeters are calibrated to read the rms value of sine wave. RMS calibration is done because DC voltage generates same amount of heat as AC voltage.

25 The rms value of sine wave is given as, V rms = V 2 n 1/2 The average value of sine wave is given as, V av = V n

26 Average Responding Detectors

27 The multimeter is calibrated for rms input voltage which is filtered, averaged & then displayed. The capacitors act as filter capacitors for rectifier diodes & coupling capacitors for the feedback signals. The diodes act as switches to maintain unidirectional meter current despite of instantaneous polarity changes of the input signal.

28 Peak Responding Detectors

29 The capacitor charges through the diode to the peak value & the meter circuit responds to the capacitor voltage. The capacitor discharges due to high impedance of amplifier so it charges to peak voltage.

30 Advantages of Peak Responding Detectors The diode & capacitor can be removed & placed in the probe when no pre amplification is required. The peak responding voltmeter is able to measure frequencies up to hundred of MHz with a minimum of circuit loading.

31 Disadvantages of Peak Responding Detectors Peak responding detector is susceptibility to errors caused by harmonic distortion in the input waveform. Due to imperfect diode characterization, instrument is limited sensitive. Input waveform is not symmetrical, due to which different output is received when voltmeter leads are reversed.

32 Peak to Peak detector

33 It is also called as Voltage Doubler Circuit. The capacitors used should be large enough, so that voltage across them should not change appreciably if other capacitor is recharging.

34 Root Mean Square Detectors

35 DC Probes DC Probe Jaw:

36 AC Probe

37 AC Probe Jaw:

38 Multimeters It usually measures Current AC or DC Voltage Resistance It is further classified as Analog Multimeters Digital Multimeters

39 Analog Multimeters It works on PMMC or D Arsonval principle. It consists of a set of resistors & a rectifier unit. It is provided with a rotary selector switch.

40 Digital Multimeters Modern multimeters are often digital due to their accuracy, durability and extra features. They provide high accuracy, have high input impedance & are of smaller size. They employ analog to digital converter & have a digital readout display as output.

41

42

43 Bench Type Multimeter They are used to measure high degree of accuracy. They can measure voltage down to 10 nv, current down to 1pA and resistance as high as 200 T.

44 Comparison Between Anaolg Multimeters & Digital Multimeters Analog multimeter is less costly compared to digital due to simple construction & as no power supply required. Visual indication of changes in analog multimeters is not good due to damping torque effect. While in digital multimeter, excellent visual indication is acquired. Analog multimeters are not as accurate as the digital multimeter as the magnetic effect in the coil degrades. In an analog multimeter, the range has to be adjusted by the user. Whereas in a digital multimeter, the range is adjusted automatically. In a digital multimeter, the rotary switch can be easily rotated to tune the circuit to its peak.

45 LCR Meters

46 Digital LCR Meter

ANALOG AND DIGITAL INSTRUMENTS

ANALOG AND DIGITAL INSTRUMENTS ANALOG AND DIGITAL INSTRUMENTS Digital Voltmeter (DVM) Used to measure the ac and dc voltages and displays the result in digital form. Types: Ramp type DVM Integrating type DVM Potentiometric type DVM

More information

4. Digital Measurement of Electrical Quantities

4. Digital Measurement of Electrical Quantities 4.1. Concept of Digital Systems Concept A digital system is a combination of devices designed for manipulating physical quantities or information represented in digital from, i.e. they can take only discrete

More information

Sine waves by far the most important form of alternating quantity important properties are shown below

Sine waves by far the most important form of alternating quantity important properties are shown below AC DC METERS 1 Sine waves by far the most important form of alternating quantity important properties are shown below 2 Average value of a sine wave average value over one (or more) cycles is clearly zero

More information

SHRI ANGALAMMAN COLLEGE OF ENGINEERING & TECHNOLOGY (An ISO 9001:2008 Certified Institution) SIRUGANOOR,TRICHY

SHRI ANGALAMMAN COLLEGE OF ENGINEERING & TECHNOLOGY (An ISO 9001:2008 Certified Institution) SIRUGANOOR,TRICHY SHRI ANGALAMMAN COLLEGE OF ENGINEERING & TECHNOLOGY (An ISO 9001:2008 Certified Institution) SIRUGANOOR,TRICHY-621105. DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING EI 1306-MEASUREMENT AND INSTRUMENTATION

More information

CHAPTER 6 DIGITAL INSTRUMENTS

CHAPTER 6 DIGITAL INSTRUMENTS CHAPTER 6 DIGITAL INSTRUMENTS 1 LECTURE CONTENTS 6.1 Logic Gates 6.2 Digital Instruments 6.3 Analog to Digital Converter 6.4 Electronic Counter 6.6 Digital Multimeters 2 6.1 Logic Gates 3 AND Gate The

More information

EE ELECTRICAL ENGINEERING AND INSTRUMENTATION

EE ELECTRICAL ENGINEERING AND INSTRUMENTATION EE6352 - ELECTRICAL ENGINEERING AND INSTRUMENTATION UNIT V ANALOG AND DIGITAL INSTRUMENTS Digital Voltmeter (DVM) It is a device used for measuring the magnitude of DC voltages. AC voltages can be measured

More information

Electronic Instrument Disadvantage of moving coil meter Low input impedance High loading error for low-voltage range voltmeter

Electronic Instrument Disadvantage of moving coil meter Low input impedance High loading error for low-voltage range voltmeter EIE 240 Electrical and Electronic Measurement Class 6, February 20, 2015 1 Electronic Instrument Disadvantage of moving coil meter Low input impedance High loading error for low-voltage range voltmeter

More information

EEE312: Electrical measurement & instrumentation

EEE312: Electrical measurement & instrumentation University of Turkish Aeronautical Association Faculty of Engineering EEE department EEE312: Electrical measurement & instrumentation Digital Electronic meters BY Ankara March 2017 1 Introduction The digital

More information

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC Certified) MODEL ANSWER

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC Certified) MODEL ANSWER MODEL ANSWER SUMMER 17 EXAMINATION Subject Title: Electronic Instruments and Measurements Subject Code: Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word

More information

Digital multimeter IENGINEERS- CONSULTANTS LECTURE NOTES SERIES ELECTRONICS ENGINEERING 1 YEAR UPTU. Page 1

Digital multimeter IENGINEERS- CONSULTANTS LECTURE NOTES SERIES ELECTRONICS ENGINEERING 1 YEAR UPTU. Page 1 Digital multimeter Measurement of any quantity is a result of comparison between the quantity to be measured and a definite world wide standard. The instruments which are used for such comparison are called

More information

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC Certified) SUMMER 2013 EXAMINATION

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC Certified) SUMMER 2013 EXAMINATION MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC 27001 2005 Certified) SUMMER 2013 EXAMINATION Subject Code: 12117 Model Answer Page No: 1 Important Instructions to examiners: 1) The

More information

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC Certified)

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC Certified) Q. No. WINTER 16 EXAMINATION (Subject Code: 17317) Model Answer Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer

More information

Table of Contents...2. About the Tutorial...6. Audience...6. Prerequisites...6. Copyright & Disclaimer EMI INTRODUCTION Voltmeter...

Table of Contents...2. About the Tutorial...6. Audience...6. Prerequisites...6. Copyright & Disclaimer EMI INTRODUCTION Voltmeter... 1 Table of Contents Table of Contents...2 About the Tutorial...6 Audience...6 Prerequisites...6 Copyright & Disclaimer...6 1. EMI INTRODUCTION... 7 Voltmeter...7 Ammeter...8 Ohmmeter...8 Multimeter...9

More information

Half-wave Rectifier AC Meters

Half-wave Rectifier AC Meters Note-4 1 Half-wave Rectifier AC Meters Disadvantages: 1. In negative half-cycle, reverse current flows through the circuit reduces average value of current meter reads lower than actual. 2. High peak inverse

More information

b) State the types of standards of measurement. 2M

b) State the types of standards of measurement. 2M MODEL ANSWER WINTER 17 EXAMINATION Subject Title: Electronic Instruments & Measurements Subject Code: 17317 I m p o r t a n t I n s t r u c t i o n s t o e x a m i n e r s : 1) The answers should be examined

More information

LINEAR IC APPLICATIONS

LINEAR IC APPLICATIONS 1 B.Tech III Year I Semester (R09) Regular & Supplementary Examinations December/January 2013/14 1 (a) Why is R e in an emitter-coupled differential amplifier replaced by a constant current source? (b)

More information

Rayat Shikshan Sanstha s Karmaveer Bhaurao Patil Polytechnic, Satara. Sub: Electrical Engineering Assignment No: 1

Rayat Shikshan Sanstha s Karmaveer Bhaurao Patil Polytechnic, Satara. Sub: Electrical Engineering Assignment No: 1 Assignment No: 1 1) Define Precision and Dead zone 2) Define 1) Speed of response 2) Lag 3) Fidelity 4)dynamic error 3) Define Standard and State its classification 4) What is Calibration & State its necessity

More information

Dedan Kimathi University of technology. Department of Electrical and Electronic Engineering. EEE2406: Instrumentation. Lab 2

Dedan Kimathi University of technology. Department of Electrical and Electronic Engineering. EEE2406: Instrumentation. Lab 2 Dedan Kimathi University of technology Department of Electrical and Electronic Engineering EEE2406: Instrumentation Lab 2 Title: Analogue to Digital Conversion October 2, 2015 1 Analogue to Digital Conversion

More information

SUMMER 15 EXAMINATION

SUMMER 15 EXAMINATION SUMMER 15 EXAMINATION Subject Code: 17317 Model Answer Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. 2)

More information

Exercise 7 AC voltage measurements peak responding detectors

Exercise 7 AC voltage measurements peak responding detectors Exercise 7 AC voltage measurements peak responding detectors 1. Aim of the exercise The aim of the exercise is to familiarize students with the AC voltage measurements by means of peak responding detectors.

More information

Analytical Chemistry II

Analytical Chemistry II Analytical Chemistry II L3: Signal processing (selected slides) Semiconductor devices Apart from resistors and capacitors, electronic circuits often contain nonlinear devices: transistors and diodes. The

More information

UNIT 2. Q.1) Describe the functioning of standard signal generator. Ans. Electronic Measurements & Instrumentation

UNIT 2. Q.1) Describe the functioning of standard signal generator. Ans.   Electronic Measurements & Instrumentation UNIT 2 Q.1) Describe the functioning of standard signal generator Ans. STANDARD SIGNAL GENERATOR A standard signal generator produces known and controllable voltages. It is used as power source for the

More information

DIPLOMA COURSE IN ELECTRONICS AND COMMUNICATION ENGINEERING

DIPLOMA COURSE IN ELECTRONICS AND COMMUNICATION ENGINEERING Department of Technical Education DIPLOMA COURSE IN ELECTRONICS AND COMMUNICATION ENGINEERING Third Semester ELECTRONIC MEASUREMENTS AND INSTRUMENTATION Contact Hours/Week : 04 Contact Hours/Semester :

More information

EE Chapter 7 Measuring Instruments

EE Chapter 7 Measuring Instruments EE 2145230 Chapter 7 Measuring Instruments 7.1 Meter Movements The basic principle of many electric instruments is that of the galvanometer. This is a device which reacts to minute electromagnetic influences

More information

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC Certified) SUMMER 14 EXAMINATION Model Answer

MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC Certified) SUMMER 14 EXAMINATION Model Answer MAHARASHTRA STATE BOARD OF TECHNICAL EDUCATION (Autonomous) (ISO/IEC 27001 2005 Certified) SUMMER 14 EXAMINATION Model Answer Subject Code : 17317 Page No: 1 Important Instructions to examiners: 1) The

More information

B.E. SEMESTER III (ELECTRICAL) SUBJECT CODE: X30902 Subject Name: Analog & Digital Electronics

B.E. SEMESTER III (ELECTRICAL) SUBJECT CODE: X30902 Subject Name: Analog & Digital Electronics B.E. SEMESTER III (ELECTRICAL) SUBJECT CODE: X30902 Subject Name: Analog & Digital Electronics Sr. No. Date TITLE To From Marks Sign 1 To verify the application of op-amp as an Inverting Amplifier 2 To

More information

A.C voltmeters using rectifier

A.C voltmeters using rectifier Lecture 5 A.C voltmeters using rectifier The PMMC movement used in d.c. voltmeters can be effectively used in a.c. voltmeters. The rectifier is used to convert a.c. voltage to be measured, to d.c. This

More information

ANALOG TO DIGITAL (ADC) and DIGITAL TO ANALOG CONVERTERS (DAC)

ANALOG TO DIGITAL (ADC) and DIGITAL TO ANALOG CONVERTERS (DAC) COURSE / CODE DIGITAL SYSTEM FUNDAMENTALS (ECE421) DIGITAL ELECTRONICS FUNDAMENTAL (ECE422) ANALOG TO DIGITAL (ADC) and DIGITAL TO ANALOG CONVERTERS (DAC) Connecting digital circuitry to sensor devices

More information

Small signal Amplifier stages. Figure 5.2 Classification of power amplifiers

Small signal Amplifier stages. Figure 5.2 Classification of power amplifiers 5.1 Introduction When the power requirement to drive the load is in terms of several Watts rather than mili-watts the power amplifiers are used. Power amplifiers form the last stage of multistage amplifiers.

More information

1 Second Time Base From Crystal Oscillator

1 Second Time Base From Crystal Oscillator 1 Second Time Base From Crystal Oscillator The schematic below illustrates dividing a crystal oscillator signal by the crystal frequency to obtain an accurate (0.01%) 1 second time base. Two cascaded 12

More information

HIGH LOW Astable multivibrators HIGH LOW 1:1

HIGH LOW Astable multivibrators HIGH LOW 1:1 1. Multivibrators A multivibrator circuit oscillates between a HIGH state and a LOW state producing a continuous output. Astable multivibrators generally have an even 50% duty cycle, that is that 50% of

More information

Chapter 2 Signal Conditioning, Propagation, and Conversion

Chapter 2 Signal Conditioning, Propagation, and Conversion 09/0 PHY 4330 Instrumentation I Chapter Signal Conditioning, Propagation, and Conversion. Amplification (Review of Op-amps) Reference: D. A. Bell, Operational Amplifiers Applications, Troubleshooting,

More information

SYLLABUS MODULE 1: Measurement and Error: Definitions, Accuracy and Precision, Significant Figures, Types of Error, Statistical Analysis, Probability

SYLLABUS MODULE 1: Measurement and Error: Definitions, Accuracy and Precision, Significant Figures, Types of Error, Statistical Analysis, Probability SYLLABUS MODULE 1: Measurement and Error: Definitions, Accuracy and Precision, Significant Figures, Types of Error, Statistical Analysis, Probability of Errors, Limiting Errors. Relevant problems. Ammeters:

More information

Design and Implementation of Economical Power Factor Transducer

Design and Implementation of Economical Power Factor Transducer Design and Implementation of Economical Power Factor Transducer Prof. P. D. Debre Akhilesh Menghare Swapnil Bhongade Snehalata Thote Sujata Barde HOD (Dept. of EE), RGCER, Nagpur RGCER, Nagpur RGCER, Nagpur

More information

MEASUREMENTS & INSTRUMENTATION ANALOG AND DIGITAL METERS

MEASUREMENTS & INSTRUMENTATION ANALOG AND DIGITAL METERS MEASUREMENTS & INSTRUMENTATION ANALOG AND DIGITAL METERS ANALOG Metering devices Provides monotonous (continuous) movement. ELECTRICAL MEASURING INSTRUMENTS ANALOG METERS A d Arsonval galvanometer (Moving

More information

AC LAB ECE-D ecestudy.wordpress.com

AC LAB ECE-D ecestudy.wordpress.com PART B EXPERIMENT NO: 1 AIM: PULSE AMPLITUDE MODULATION (PAM) & DEMODULATION DATE: To study Pulse Amplitude modulation and demodulation process with relevant waveforms. APPARATUS: 1. Pulse amplitude modulation

More information

Linear Integrated Circuits

Linear Integrated Circuits Linear Integrated Circuits Single Slope ADC Comparator checks input voltage with integrated reference voltage, V REF At the same time the number of clock cycles is being counted. When the integrator output

More information

Lecture Note. DC-AC PWM Inverters. Prepared by Dr. Oday A Ahmed Website: https://odayahmeduot.wordpress.com

Lecture Note. DC-AC PWM Inverters. Prepared by Dr. Oday A Ahmed Website: https://odayahmeduot.wordpress.com Lecture Note 10 DC-AC PWM Inverters Prepared by Dr. Oday A Ahmed Website: https://odayahmeduot.wordpress.com Email: 30205@uotechnology.edu.iq Scan QR DC-AC PWM Inverters Inverters are AC converters used

More information

MODERN ACADEMY FOR ENGINEERING & TECHNOLOGY IN MAADI

MODERN ACADEMY FOR ENGINEERING & TECHNOLOGY IN MAADI MODERN ACADEMY FOR ENGINEERING & TECHNOLOGY IN MAADI 1 2/25/2018 ELECTRONIC MEASUREMENTS ELC_314 2 2/25/2018 Text Books David A. Bell, A. Foster Chin, Electronic Instrumentation & Measurements, 2 nd Ed.,

More information

Operational Amplifiers

Operational Amplifiers Operational Amplifiers Table of contents 1. Design 1.1. The Differential Amplifier 1.2. Level Shifter 1.3. Power Amplifier 2. Characteristics 3. The Opamp without NFB 4. Linear Amplifiers 4.1. The Non-Inverting

More information

Optical Power Meter Basics

Optical Power Meter Basics Optical Power Meter Basics Introduction An optical power meter measures the photon energy in the form of current or voltage from an optical detector such as a semiconductor, a thermopile, or a pyroelectric

More information

Electronic Measurements & Instrumentation UNIT What are the basic performance characteristics of a system?

Electronic Measurements & Instrumentation UNIT What are the basic performance characteristics of a system? UNIT-1 1. What are the basic performance characteristics of a system? Ans: STATIC CHARACTE RISTICS The static characteristics of an instrument are, in general, considered for instruments which are used

More information

DEPARTMENT OF ELECTRICAL ENGINEERING LAB WORK EE301 ELECTRONIC CIRCUITS

DEPARTMENT OF ELECTRICAL ENGINEERING LAB WORK EE301 ELECTRONIC CIRCUITS DEPARTMENT OF ELECTRICAL ENGINEERING LAB WORK EE301 ELECTRONIC CIRCUITS EXPERIMENT : 1 TITLE : Half-Wave Rectifier & Filter OUTCOME : Upon completion of this unit, the student should be able to: i. Construct

More information

SYLLABUS. osmania university CHAPTER - 1 : OPERATIONAL AMPLIFIER CHAPTER - 2 : OP-AMP APPLICATIONS ARATORS AND CONVERTERS

SYLLABUS. osmania university CHAPTER - 1 : OPERATIONAL AMPLIFIER CHAPTER - 2 : OP-AMP APPLICATIONS ARATORS AND CONVERTERS Contents i SYLLABUS osmania university UNIT - I CHAPTER - 1 : OPERATIONAL AMPLIFIER Operational Amplifiers-Characteristics, Open Loop Voltage Gain, Output Impedance, Input Impedance, Common Mode Rejection

More information

About the Tutorial. Audience. Prerequisites. Copyright & Disclaimer. Linear Integrated Circuits Applications

About the Tutorial. Audience. Prerequisites. Copyright & Disclaimer. Linear Integrated Circuits Applications About the Tutorial Linear Integrated Circuits are solid state analog devices that can operate over a continuous range of input signals. Theoretically, they are characterized by an infinite number of operating

More information

Chapter 2 Analog-to-Digital Conversion...

Chapter 2 Analog-to-Digital Conversion... Chapter... 5 This chapter examines general considerations for analog-to-digital converter (ADC) measurements. Discussed are the four basic ADC types, providing a general description of each while comparing

More information

DLVP A OPERATOR S MANUAL

DLVP A OPERATOR S MANUAL DLVP-50-300-3000A OPERATOR S MANUAL DYNALOAD DIVISION 36 NEWBURGH RD. HACKETTSTOWN, NJ 07840 PHONE (908) 850-5088 FAX (908) 908-0679 TABLE OF CONTENTS INTRODUCTION...3 SPECIFICATIONS...5 MODE SELECTOR

More information

Entry Level Assessment Blueprint Electronics Technology

Entry Level Assessment Blueprint Electronics Technology Blueprint Test Code: 4135 / Version: 01 Specific Competencies and Skills Tested in this Assessment: Safety Practices Demonstrate safe working procedures Explain the purpose of OSHA and how it promotes

More information

B MTS Systems Corp., Model Function Generator

B MTS Systems Corp., Model Function Generator 0189 115585-02 B MTS Systems Corp., 1988 Model 410.81 Function Generator Table of Contents Section 1 Introduction 1.1 Functional Description 1-1 1.2 Specifications 1-2 Section 2 Operation 2.1 Control Mode

More information

VALLIAMMAI ENGINEERING COLLEGE

VALLIAMMAI ENGINEERING COLLEGE VALLIAMMAI ENGINEERING COLLEGE SRM Nagar, Kattankulathur 603 203 DEPARTMENT OF ELECTRONICS AND INSTRUMENTATION ENGINEERING QUESTION BANK VI SEMESTER EI6601 Modern Electronic Instrumentation Regulation

More information

CHAPTER IV DESIGN AND ANALYSIS OF VARIOUS PWM TECHNIQUES FOR BUCK BOOST CONVERTER

CHAPTER IV DESIGN AND ANALYSIS OF VARIOUS PWM TECHNIQUES FOR BUCK BOOST CONVERTER 59 CHAPTER IV DESIGN AND ANALYSIS OF VARIOUS PWM TECHNIQUES FOR BUCK BOOST CONVERTER 4.1 Conventional Method A buck-boost converter circuit is a combination of the buck converter topology and a boost converter

More information

Circuit operation Let s look at the operation of this single diode rectifier when connected across an alternating voltage source v s.

Circuit operation Let s look at the operation of this single diode rectifier when connected across an alternating voltage source v s. Diode Rectifier Circuits One of the important applications of a semiconductor diode is in rectification of AC signals to DC. Diodes are very commonly used for obtaining DC voltage supplies from the readily

More information

DVM98. True RMS Digital Multimeter. 1 Safety information. 1.1 Preliminary. 1.2 During use

DVM98. True RMS Digital Multimeter. 1 Safety information. 1.1 Preliminary. 1.2 During use True RMS Digital Multimeter DVM98 1 Safety information This multimeter has been designed according to IEC - 1010 concerning electronic measuring instruments with an overvoltage category (CAT II) and pollution

More information

Lecture 6: Digital/Analog Techniques

Lecture 6: Digital/Analog Techniques Lecture 6: Digital/Analog Techniques The electronics signals that we ve looked at so far have been analog that means the information is continuous. A voltage of 5.3V represents different information that

More information

ELECTRICAL MEASUREMENTS

ELECTRICAL MEASUREMENTS R10 Set No: 1 1. a) Derive the expression for torque equation for a moving iron attraction type instrument and comment up on the nature of scale [8] b) Define the terms current sensitivity, voltage sensitivity

More information

For the filter shown (suitable for bandpass audio use) with bandwidth B and center frequency f, and gain A:

For the filter shown (suitable for bandpass audio use) with bandwidth B and center frequency f, and gain A: Basic Op Amps The operational amplifier (Op Amp) is useful for a wide variety of applications. In the previous part of this article basic theory and a few elementary circuits were discussed. In order to

More information

4/30/2012. General Class Element 3 Course Presentation. Practical Circuits. Practical Circuits. Subelement G7. 2 Exam Questions, 2 Groups

4/30/2012. General Class Element 3 Course Presentation. Practical Circuits. Practical Circuits. Subelement G7. 2 Exam Questions, 2 Groups General Class Element 3 Course Presentation ti ELEMENT 3 SUB ELEMENTS General Licensing Class Subelement G7 2 Exam Questions, 2 Groups G1 Commission s Rules G2 Operating Procedures G3 Radio Wave Propagation

More information

CHAPTER ELEVEN - Interfacing With the Analog World

CHAPTER ELEVEN - Interfacing With the Analog World CHAPTER ELEVEN - Interfacing With the Analog World 11.1 (a) Analog output = (K) x (digital input) (b) Smallest change that can occur in the analog output as a result of a change in the digital input. (c)

More information

Data Converters. Dr.Trushit Upadhyaya EC Department, CSPIT, CHARUSAT

Data Converters. Dr.Trushit Upadhyaya EC Department, CSPIT, CHARUSAT Data Converters Dr.Trushit Upadhyaya EC Department, CSPIT, CHARUSAT Purpose To convert digital values to analog voltages V OUT Digital Value Reference Voltage Digital Value DAC Analog Voltage Analog Quantity:

More information

Fig 1: The symbol for a comparator

Fig 1: The symbol for a comparator INTRODUCTION A comparator is a device that compares two voltages or currents and switches its output to indicate which is larger. They are commonly used in devices such as They are commonly used in devices

More information

APPENDIX D DISCUSSION OF ELECTRONIC INSTRUMENTS

APPENDIX D DISCUSSION OF ELECTRONIC INSTRUMENTS APPENDIX D DISCUSSION OF ELECTRONIC INSTRUMENTS DC POWER SUPPLIES We will discuss these instruments one at a time, starting with the DC power supply. The simplest DC power supplies are batteries which

More information

Gechstudentszone.wordpress.com

Gechstudentszone.wordpress.com 8.1 Operational Amplifier (Op-Amp) UNIT 8: Operational Amplifier An operational amplifier ("op-amp") is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended

More information

Data Conversion Circuits & Modulation Techniques. Subhasish Chandra Assistant Professor Department of Physics Institute of Forensic Science, Nagpur

Data Conversion Circuits & Modulation Techniques. Subhasish Chandra Assistant Professor Department of Physics Institute of Forensic Science, Nagpur Data Conversion Circuits & Modulation Techniques Subhasish Chandra Assistant Professor Department of Physics Institute of Forensic Science, Nagpur Data Conversion Circuits 2 Digital systems are being used

More information

Contents. Acknowledgments. About the Author

Contents. Acknowledgments. About the Author Contents Figures Tables Preface xi vii xiii Acknowledgments About the Author xv xvii Chapter 1. Basic Mathematics 1 Addition 1 Subtraction 2 Multiplication 2 Division 3 Exponents 3 Equations 5 Subscripts

More information

HAMEG Modular System Series 8000

HAMEG Modular System Series 8000 HAMEG Modular System Series 8000 In many years of practical application the HAMEG Modular System Series 8000 has proven its value to the customer. The advantages of this Modular System have been demonstrated

More information

Department of Electronics & Telecommunication Engg. LAB MANUAL. B.Tech V Semester [ ] (Branch: ETE)

Department of Electronics & Telecommunication Engg. LAB MANUAL. B.Tech V Semester [ ] (Branch: ETE) Department of Electronics & Telecommunication Engg. LAB MANUAL SUBJECT:-DIGITAL COMMUNICATION SYSTEM [BTEC-501] B.Tech V Semester [2013-14] (Branch: ETE) KCT COLLEGE OF ENGG & TECH., FATEHGARH PUNJAB TECHNICAL

More information

Acknowledgments Introduction

Acknowledgments Introduction Acknowledgments Introduction xiii xi 1 Electronic meters 1 1.1 Digital meters 2 1.2 Nondigital (analog) meters 6 1.3 Differential meters 14 1.4 Digital meter displays and ranges 16 1.5 Nondigital meter

More information

Using Circuits, Signals and Instruments

Using Circuits, Signals and Instruments Using Circuits, Signals and Instruments To be ignorant of one s ignorance is the malady of the ignorant. A. B. Alcott (1799-1888) Some knowledge of electrical and electronic technology is essential for

More information

EXPERIMENT 2.2 NON-LINEAR OP-AMP CIRCUITS

EXPERIMENT 2.2 NON-LINEAR OP-AMP CIRCUITS 2.16 EXPERIMENT 2.2 NONLINEAR OPAMP CIRCUITS 2.2.1 OBJECTIVE a. To study the operation of 741 opamp as comparator. b. To study the operation of active diode circuits (precisions circuits) using opamps,

More information

Measurement of Resistance and Potentiometers

Measurement of Resistance and Potentiometers Electrical Measurements International Program Department of Electrical Engineering UNIVERSITAS INDONESIA Measurement of Resistance and Potentiometers Jahroo Renardi Lecturer : Ir. Chairul Hudaya, ST, M.Eng.,

More information

Analog-to-Digital Converter (ADC) And Digital-to-Analog Converter (DAC)

Analog-to-Digital Converter (ADC) And Digital-to-Analog Converter (DAC) 1 Analog-to-Digital Converter (ADC) And Digital-to-Analog Converter (DAC) 2 1. DAC In an electronic circuit, a combination of high voltage (+5V) and low voltage (0V) is usually used to represent a binary

More information

Specifying A D and D A Converters

Specifying A D and D A Converters Specifying A D and D A Converters The specification or selection of analog-to-digital (A D) or digital-to-analog (D A) converters can be a chancey thing unless the specifications are understood by the

More information

Exercise 6 AC voltage measurements average responding voltmeters

Exercise 6 AC voltage measurements average responding voltmeters Exercise 6 AC voltage measurements average responding voltmeters 1. Aim of the exercise The aim of the exercise is to familiarize students with the AC voltage measurements by means of rectified average

More information

MaxLinear. MxL5005 Global Standards IC Tuner. Circuit Analysis

MaxLinear. MxL5005 Global Standards IC Tuner. Circuit Analysis MaxLinear MxL5005 Global Standards IC Tuner Circuit Analysis For questions, comments, or more information about this report, or for any additional technical needs concerning semiconductor technology, please

More information

Lab 7: DELTA AND SIGMA-DELTA A/D CONVERTERS

Lab 7: DELTA AND SIGMA-DELTA A/D CONVERTERS ANALOG & TELECOMMUNICATION ELECTRONICS LABORATORY EXERCISE 6 Lab 7: DELTA AND SIGMA-DELTA A/D CONVERTERS Goal The goals of this experiment are: - Verify the operation of a differential ADC; - Find the

More information

WAVEFORM GENERATOR CIRCUITS USING OPERATIONAL AMPLIFIERS

WAVEFORM GENERATOR CIRCUITS USING OPERATIONAL AMPLIFIERS 15EEE287 Electronic Circuits & Simulation Lab - II Lab #8 WAVEFORM GENERATOR CIRCUITS USING OPERATIONAL AMPLIFIERS OBJECTIVE The purpose of the experiment is to design and construct circuits to generate

More information

A-D and D-A Converters

A-D and D-A Converters Chapter 5 A-D and D-A Converters (No mathematical derivations) 04 Hours 08 Marks When digital devices are to be interfaced with analog devices (or vice a versa), Digital to Analog converter and Analog

More information

Question Paper Code: 21398

Question Paper Code: 21398 Reg. No. : Question Paper Code: 21398 B.E./B.Tech. DEGREE EXAMINATION, MAY/JUNE 2013 Fourth Semester Electrical and Electronics Engineering EE2254 LINEAR INTEGRATED CIRCUITS AND APPLICATIONS (Regulation

More information

Circuit Applications of Multiplying CMOS D to A Converters

Circuit Applications of Multiplying CMOS D to A Converters Circuit Applications of Multiplying CMOS D to A Converters The 4-quadrant multiplying CMOS D to A converter (DAC) is among the most useful components available to the circuit designer Because CMOS DACs

More information

Basic Electronics Prof. T.S. Natarajan Department of Physics Indian Institute of Technology, Madras

Basic Electronics Prof. T.S. Natarajan Department of Physics Indian Institute of Technology, Madras Basic Electronics Prof. T.S. Natarajan Department of Physics Indian Institute of Technology, Madras Lecture 39 Silicon Controlled Rectifier (SCR) (Construction, characteristics (Dc & Ac), Applications,

More information

GATE: Electronics MCQs (Practice Test 1 of 13)

GATE: Electronics MCQs (Practice Test 1 of 13) GATE: Electronics MCQs (Practice Test 1 of 13) 1. Removing bypass capacitor across the emitter leg resistor in a CE amplifier causes a. increase in current gain b. decrease in current gain c. increase

More information

SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road QUESTION BANK (DESCRIPTIVE) UNIT I

SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road QUESTION BANK (DESCRIPTIVE) UNIT I SIDDHARTH GROUP OF INSTITUTIONS :: PUTTUR Siddharth Nagar, Narayanavanam Road 517583 QUESTION BANK (DESCRIPTIVE) Subject with Code : EMI(16EC416) Year & Sem: III B.Tech & I Sem Course & Branch: B.Tech

More information

State the application of negative feedback and positive feedback (one in each case)

State the application of negative feedback and positive feedback (one in each case) (ISO/IEC - 700-005 Certified) Subject Code: 073 Model wer Page No: / N Important Instructions to examiners: ) The answers should be examined by key words and not as word-to-word as given in the model answer

More information

Capacitive Touch Sensing Tone Generator. Corey Cleveland and Eric Ponce

Capacitive Touch Sensing Tone Generator. Corey Cleveland and Eric Ponce Capacitive Touch Sensing Tone Generator Corey Cleveland and Eric Ponce Table of Contents Introduction Capacitive Sensing Overview Reference Oscillator Capacitive Grid Phase Detector Signal Transformer

More information

Power Amplifiers. Class A Amplifier

Power Amplifiers. Class A Amplifier Power Amplifiers The Power amplifiers amplify the power level of the signal. This amplification is done in the last stage in audio applications. The applications related to radio frequencies employ radio

More information

Verification of competency for ELTR courses

Verification of competency for ELTR courses Verification of competency for ELTR courses The purpose of these performance assessment activities is to verify the competence of a prospective transfer student with prior work experience and/or formal

More information

3. Diode, Rectifiers, and Power Supplies

3. Diode, Rectifiers, and Power Supplies 3. Diode, Rectifiers, and Power Supplies Semiconductor diodes are active devices which are extremely important for various electrical and electronic circuits. Diodes are active non-linear circuit elements

More information

DELTA MODULATION. PREPARATION principle of operation slope overload and granularity...124

DELTA MODULATION. PREPARATION principle of operation slope overload and granularity...124 DELTA MODULATION PREPARATION...122 principle of operation...122 block diagram...122 step size calculation...124 slope overload and granularity...124 slope overload...124 granular noise...125 noise and

More information

3.4. Operation in the Reverse Breakdown

3.4. Operation in the Reverse Breakdown 3.4. peration in the Reverse Breakdown Under certain circumstances, diodes may be intentionally used in the reverse breakdown region These are referred to as Zener Diode or Breakdown Diode Voltage regulator

More information

Applications of the LM392 Comparator Op Amp IC

Applications of the LM392 Comparator Op Amp IC Applications of the LM392 Comparator Op Amp IC The LM339 quad comparator and the LM324 op amp are among the most widely used linear ICs today. The combination of low cost, single or dual supply operation

More information

RF Generators. Requirements:

RF Generators. Requirements: Requirements: RF Generators to deliver a requested forward power (adjustable) level into an RF system power level is adjusted manually, or power level is controlled by a digital or analog input signal

More information

The steeper the phase shift as a function of frequency φ(ω) the more stable the frequency of oscillation

The steeper the phase shift as a function of frequency φ(ω) the more stable the frequency of oscillation It should be noted that the frequency of oscillation ω o is determined by the phase characteristics of the feedback loop. the loop oscillates at the frequency for which the phase is zero The steeper the

More information

332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title: Function Generators and Oscilloscopes Suggested Equipment:

332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title: Function Generators and Oscilloscopes Suggested Equipment: RUTGERS UNIVERSITY The State University of New Jersey School of Engineering Department Of Electrical and Computer Engineering 332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title:

More information

A Simplified Test Set for Op Amp Characterization

A Simplified Test Set for Op Amp Characterization A Simplified Test Set for Op Amp Characterization INTRODUCTION The test set described in this paper allows complete quantitative characterization of all dc operational amplifier parameters quickly and

More information

Digital Multimeter with Backlight

Digital Multimeter with Backlight MODEL: D03126 Digital Multimeter with Backlight 1 CONTENTS Page Number Description 3 Important Safety Information 3 What s Included? 4 Overview 4 Front Panel Description 5 General Specification 5 DC Voltage

More information

Introductory Electronics for Scientists and Engineers

Introductory Electronics for Scientists and Engineers Introductory Electronics for Scientists and Engineers Second Edition ROBERT E. SIMPSON University of New Hampshire Allyn and Bacon, Inc. Boston London Sydney Toronto Contents Preface xiü 1 Direct Current

More information

Q.1 a) Attempt any SIX of the following: 12M. (i) Give comparison between active transducer and passive transducer. Ans:- (Any Two) 1M each

Q.1 a) Attempt any SIX of the following: 12M. (i) Give comparison between active transducer and passive transducer. Ans:- (Any Two) 1M each Page 1 of 26 Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the Model answer scheme. 2) The model answer and the answer written

More information

Transistor Design & Analysis (Inverter)

Transistor Design & Analysis (Inverter) Experiment No. 1: DIGITAL ELECTRONIC CIRCUIT Transistor Design & Analysis (Inverter) APPARATUS: Transistor Resistors Connecting Wires Bread Board Dc Power Supply THEORY: Digital electronics circuits operate

More information

Design and Fabrication of High Frequency Linear Function Generator with Digital Frequency Counter using MAX038 and a PIC microcontroller

Design and Fabrication of High Frequency Linear Function Generator with Digital Frequency Counter using MAX038 and a PIC microcontroller International Journal of Latest Tr ends in Engineering and Technology Vol.(7)Issue(3), pp. 263-270 DOI: http://dx.doi.org/10.21172/1.73.536 e-issn:2278-621x Design and Fabrication of High Frequency Linear

More information

Wave Measurement & Ohm s Law

Wave Measurement & Ohm s Law Wave Measurement & Ohm s Law Marking scheme : Methods & diagrams : 2 Graph plotting : 1 Tables & analysis : 2 Questions & discussion : 3 Performance : 2 Aim: Various types of instruments are used by engineers

More information