FM/AM DIGITAL-SYNTHESIZER TUNER F-208. Operating Instructions Manual de instruções

Transcription

1 FM/AM DIGITAL-SYNTHESIZER TUNER F-208 Operating Instructions Manual de instruções

2 IMPORTANT The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D _En Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your unit properly. After you have finished reading the instructions, keep them in a safe place for future reference. In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However, the method of connecting and operating the unit is the same. WARNING: The apparatus is not waterproofs, to prevent fire or shocks hazard, do not expose this apparatus to rain or moisture and do not put any water source near this apparatus, such as vase, flower pot, cosmetics container and medicine bottle etc. D _En Voltage selector You can find the voltage selector switch on the rear panel of multi-voltage models. The factory setting for the voltage selector is 220 V. Please set it to the correct voltage for your country or region. For Taiwan, please set to 110 V before using. Before changing the voltage, disconnect the AC power cord. Use a medium size screwdriver to change the voltage selector switch. WARNING: BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230V or 120V) written on the rear panel. D _En WARNING: No naked flame sources, such as lighted candle, should be placed on the apparatus. If naked flame sources accidentally fall down, fire spread over the apparatus then may cause fire. D a_En WARNING: Slot and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, to prevent fire hazard, the openings should never be blocked and covered with items, such as newspapers, table-cloths, curtains, etc. Also do not put the apparatus on the thick carpet, bed, sofa, or fabric having a thick pile. D b_En Operating Environment Operating environment temperature and humidity: +5 ºC +35 ºC (+41 ºF +95 ºF); less than 85 %RH (cooling vents not blocked) Do not install in the following locations Location exposed to direct sunlight or strong artificial light Location exposed to high humidity, or poorly ventilated location D c_En Medium-size screwdriver D _En This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period. K041_En CAUTION The POWER switch does not completely separates the unit from the MAINS in off position. Therefore install the unit suitable places easy to disconnect the MAINS plug in case of the accident. The MAINS plug of unit should be unplugged from the wall socket when left unused for a long period of time. D b_En 2 En

3 CONTENTS FEATURES... 3 CHECKING THE ACCESSORIES... 3 INSTALLATION... 4 CONNECTIONS... 5 ANTENNA CONNECTIONS... 6 FRONT PANEL FACILITIES... 7 BASIC TUNING OPERATIONS AUTO AND MANUAL TUNING...10 DIRECT ACCESS TUNING PRESETTING STATIONS...12 PRESET STATIONS PRESET STATION TUNING...13 MEMORY SCAN MANUAL STATION NAME MEMORY TROUBLESHOOTING SPECIFICATIONS FEATURES 7 RF ATT A built-in attenuator (RF ATT) can be switched on or off for proper reception of strong boradcast stations. 7 Random 30-station presetting A total of 30 FM and AM stations can be preset into the memory circuit. 7 Manual station name memory Using up to 4 characters, you can store a name of your choice for preset FM/AM broadcast stations 1 to Memory scan This function receives preset stations within a class (A, B or C) in order, letting you select a desired station while checking what program the station is broadcasting. 7 Energy-saving design This unit is designed to use minimal electricity when power is switched OFF (during Standby). Regarding the value of the power consumption in standby mode, refer to SPECIFICATIONS on page 17. CHECKING THE ACCESSORIES AM loop antenna FM T-type antenna Audio cord Control cord 3 En

4 INSTALLATION CHANNEL STEP SETTING Before using the unit for the first time, be sure to set the correct channel step (FM and AM) for your area. If the channel step setting is incorrect, tuning to the correct frequency will not be possible, and poor sound quality due to distortion and noise will prevent reproduction of the received signal. FM 100 khz, AM 10 khz: Set to this position for areas with an FM reception step of 100 khz and AM 10 khz. FM 50 khz, AM 9 khz: Set to this position, for areas with an FM reception step of 50 khz and AM 9 khz. NOTE: When unsure about the channel allocation for your area, consult your dealer for correct information. To change channel steps Setting the FM channel step to 100kHz and the AM channel step to 10kHz: When power is in standby, press the STANDBY/ON switch while pressing STATION CALL button 0/10 to switch power ON. Setting the FM channel step to 50kHz and the AM channel step to 9kHz: When power is in standby, press the STANDBY/ON switch while pressing STATION CALL button 9 to switch power ON. LOCATION Install the tuner in a well-ventilated location where it will not be exposed to high temperatures or humidity. Do not install the tuner in a location which is exposed to direct rays of the sun, or near hot appliances or radiators. Excessive heat can adversely affect the cabinet and internal components. Installation of the tuner in a damp or dusty environment may result in a malfunction or accident. (Also avoid installation near cookers, etc., where the tuner may be exposed to smoke, steam, or heat.) CONDENSATION When this unit is brought into a warm room from previously cold surroundings or when the room temperature rises sharply,condensation may from inside,and the unit may not be able to attain its full performance. In this case, allow the unit to stand for about an hour or raise the room temperature gradually. POWER-CORD CAUTION Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement. Maintenance of external surfaces Use a polishing cloth or dry cloth to wipe off dust and dirt. When the surfaces are very dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleaners. Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surfaces. 4 En

5 CONNECTIONS Before making or changing the connections, switch off the power switch and disconnect the power cord from the AC outlet. Accessory FM T-type antenna Stereo amplifier Outdoor FM antenna Accessory AM loop antenna GND INPUT PHONO CD TUNER L R Accessory Audio cord ANTENNA TWO VOLTAGE SERECTORS FM UNBAL 75Ω AM LOOP ANTENNA L R OUTPUT CONTROL IN OUT V V 240V 110V 220V V Connecting the FM T-type antenna and AM loop antenna CONTROL terminals Plug the power cord into an ACwall socket. 15 mm 1. Strip and twist the ends of the wires. 2. With tabs beneath connector down, insert wires from antenna. Pin plug connecting cord Connect the white plug to the white terminal (L) and the red plug to the red terminal (R). Make sure that the connections are secure. Left channel White plug CONTROL terminals When using together with a Pioneer component bearing the Î mark, connect the CONTROL IN terminal on the rear panel of the tuner to the CONTROL OUT terminal on the component using the supplied control cord. This will enable the tuner to be controlled from a distance with the remote control unit supplied with the component. When this feature is not used, connection is not necessary. For instructions regarding connection and operation, please refer to the operating instructions of your stereo component. Right channel Antenna ground ANTENNA FM UNBAL AM LOOP 75Ω ANTENNA Red plug Stereo Amplifier F-208 CD Player Cassette Deck NOTE: The (signal earth) helps reduce noise when an antenna is connected. It is not a safety earth. CONTROL IN OUT CONTROL IN OUT CONTROL IN OUT CONTROL IN OUT CAUTION: Never make the ground connection to a gas pipe as sparks can cause the gas ignite. 5 En

6 CONNECTIONS ANTENNA CONNECTIONS Radio reception is not possible unless the antenna is properly connected. The strength of broadcast signals varies from one area to another. Signal propagation is especially poor in metropolitan areas, where there are many tall buildings, and also in mountainous areas. Proper antenna installation is vital to good reception. AM ANTENNA The AM loop antenna supplied with the tuner should be connected to the AM antenna terminals. The antenna should be placed at a distance from the tuner, and should not be allowed to touch metallic objects. Avoid placing it near CD players, personal computers, television sets, and other devices generating radio frequencies. Setting up the AM loop antenna Insert the clip on the bottom of the antenna into the groove on the leg. Place the antenna on a level surface and rotate it to locate the orientation that yields the best reception. To permanently affix the antenna,screw the leg to a wall or post before assembling (affixing the antenna in the direction that gives the best reception). Outdoor AM antenna If reception is still poor even when a lead antenna has been stretched out indoors, stretch out a vinyl-coated wire and secure it outdoors. Connecting the external AM antenna Indoor AM antenna AM loop antenna Outdoor AM antenna NOTE: Do not detach the AM loop antenna when using an external AM antenna. FM ANTENNA FM T-type antenna attachment Connect the accessory FM T-type antenna to the FM terminals. Stretch the antenna out to its full length, and affix it to a wall, etc. The accessory FM T-type antenna must be connected to ensure proper reception. Lead wire Leg Correct Wrong Wrong AM Loop Antenna Connection The accessory AM loop antenna must be connected to ensure proper reception. External AM antenna Indoor AM antenna Provide a vinyl-coated wire (5 to 6 meters long). Secure one end to the AM terminal marked AM LOOP AN- TENNA and the other end to a wall or other high location. Outdoor external FM antenna installation Use an external antenna when the signals from the station are weak and cannot be picked up by the accessory T-type FM antenna, or when the sound heard is accompanied by too much noise. 75 Ω coaxial cable 6 En

7 FRONT PANEL FACILITIES FM/AM DIGITAL-SYNTHESIZER TUNER X <? Î MEMORY CLASS DIRECT TUNING MODE TUNING STANDBY/ON MEMORY SCAN CHARACTER DISPLAY MODE RF ATT MPX MODE BAND /10 - = ~! 1 STANDBY/ON switch This is the switch for electric power. ON... When set to ON position, power is supplied and the unit becomes operational. STANDBY... When set to STANDBY position, the main power flow is cut and the unit is no longer fully operational. A minute flow of power feeds the unit to maintain operation readiness. NOTES: The memory will be backed up so long as the power cord is unplugged. If the power cord is unplugged, the memory will be retained for several days. When not using the unit for a long period, disconnect the power cord. 2 MEMORY SCAN button When this button is pressed, preset stations within a class (A, B or C) are received in order. (See page 13) 3 CHARACTER button You can use it to input station names manually. (see page 14) 4 DISPLAY MODE button When in the Preset Station Selection mode, pressing this button changes display indications. If no station names are memorized, this button has no function. When no station name is memorized,the DISPLAY MODE button becomes invalid. 6 MEMORY button Use to preset stations. This is also used for FM or AM broadcast manual station name character selection. 7 CLASS button Use to switch between preset memory classes A to C. In each class, 10 stations can be memorized using the STATION CALL buttons, enabling a total of 30 stations to be memorized. 8 DIRECT button When this button is pressed, the STATION CALL buttons function as ten-key number buttons for direct input of the desired reception frequency. Press again to cancel this mode. 9 TUNING MODE button Each time you press this button, the TUNING knob's function changes as follows. Manual tuning mode Preset station tuning mode Auto tuning mode 0 TUNING knob Use for tuning. To raise the frequency, turn in a clockwise direction; to lower the frequency, turn counterclockwise. In the Station Name input mode, the TUNING knob is used to select characters. When presetting a station or selecting a preset station, you can also turn this knob to select a desired station number. 5 Operating display 7 En

8 FRONT PANEL FACILITIES - RF ATT button Set this button to on when receiving strong FM signals (nearby stations) to reduce sound distortion (RF ATT indicator lights). Normally, this button should be set to off. This button does not affect AM reception. NOTE: This button s status is preset for each station in station memory. ~ BAND button The button is used to select either FM or AM reception.! STATION CALL buttons Use these buttons to preset stations and to receive the already preset stations. These are also used when performing direct access tuning. = MPX (multiplex) MODE button Mode changes as follows each time this button is pressed. AUTO MONO This button does not affect AM reception. AUTO: AUTO is not displayed. Normally leave in this mode for reception. When a stereo FM broadcast is received, it will be automatically reproduced in stereo sound and the STEREO indicator lights up. MONO: MONO indicator lights up. To receive stereo broadcasts in monaural. If there is too much noise during stereo reception of a weak signal, you can reduce the level of noise by switching to MONO. NOTES: This button s status is preset for each station in station memory. When the signal level is too weak for reception, sound output is automatically muted. If sound is muted when the selected mode is AUTO, switching to MONO lets you hear the broadcast. 8 En

9 FRONT PANEL FACILITIES Operating display MEMORY AUTO RF ATT MONO STEREO TUNED MEMORY indicator Lights when presetting stations. 2 AUTO indicator Lights during auto tuning mode. 3 Frequency and character display section Band and frequency data is displayed. 4 RF ATT indicator Stays lit while RF ATT button is on. 5 MONO indicator Stays lit while MPX MODE button is set to MONO. 6 STEREO indicator Lights up when a stereo broadcast is received (the indicator does not light when the MPX MODE button is set to MONO). 7 TUNED indicator Lights when a broadcast is received. 9 En

10 BASIC TUNING OPERATIONS The following steps show you how to tune in FM and AM radio broadcasts using Auto and Manual Tuning. If you already know the exact frequency of the station you want, see Direct Access Tuning on the following page. AUTO AND MANUAL TUNING 1 MPX MODE RF ATT 2 1. Turn the STANDBY/ON switch ON. 2. Press the desired BAND button. 3. Tuning into the frequency of a desired station. Press the TUNING MODE button to select the tuning mode. Each time you press this button, the tuning mode changes as follows. Manual tuning mode Tune into desired frequency with the TUNING knob. During auto tuning, the AUTO indicator in the display lights. No indicator lights during manual tuning. During preset station tuning, the station number or station name is displayed. 4. To receive another station in the same band, repeat step 3. To receive a station in the other band, repeat steps 2 and Adjust the volume and tone of the stereo amplifier. 3 3 Auto tuning mode Preset station tuning mode [Manual tuning mode] To raise the frequency, turn clockwise; to lower the frequency, turn counterclockwise. [Auto tuning mode] To tune into a frequency higher than the one indicated, turn the TUNING knob clockwise. To tune into a frequency lower than the one indicated, turn the TUNING knob counterclockwise; release when the frequency indication starts changing. The frequency display changes, and tuning automatically stops when a frequency that can be received is found.to search for another station, turn the TUNING knob once more. NOTES: (On auto tuning) Because of the high sensitivity of this unit, it may automatically stop even at very weak overseas stations. The same can happen with aggregate radio noise emitted in cities. During reception of an AM broadcast, auto tuning of only strong local stations is possible by changing the direction of the loop antenna or folding it down. After tuning, move the loop antenna back to its previous position. Tune extremely weak stations with manual tuning. If the radio waves of available stereo stations are weaker than a certain level,the auto-tuning may not function for these stations. (When receiving FM broadcasts) If there is distortion because the radio signal is too strong, press the RF attenuator (RF ATT) button to light the RF ATT indicator. If there is too much noise during reception of an FM stereo broadcast, press the MPX MODE button to light the MONO indicator. Switching to monaural reception results in clearer reception. The TUNED indicator When the TUNED indicator is not lit, reception is not possible even if the tuning frequency is correct. This is because the antenna terminal input is too weak. Check whether the antenna cable is firmly connected. If it is, consult your nearest dealer and install an outdoor antenna. Last station memory When the STANDBY/ON switch is pressed to turn the power on, the last station received before the power was turned off will be received again. When the power is ON and the BAND button is pressed, the last station received on that band will be received again. 10 En

11 BASIC TUNING OPERATIONS DIRECT ACCESS TUNING When you know the frequency of the desired station, the frequency can be input directly using the STATION CALL buttons in the following way. 1 3 <Example> To receive FM MHz. 1 Press the DIRECT button. 2 Press 1 3 Press 0/10 4 Press 6 5 Press 0/10 6 Press 0/10 1 DIRECT Turn the STANDBY/ON switch ON. 3 0/10 2. Select the desired band with the BAND button Press the DIRECT button. 4. Input the desired station frequency using the STATION CALL buttons /10 0/10 To cancel frequency input Direct access is canceled when the DIRECT button is pressed again. Under the following conditions, direct access is canceled and the unit returns to the condition in effect before direct access was selected: 1If there is no key input for approximately five seconds after the DIRECT button is pressed. 2If more than approximately five seconds elapse between number inputs. STEREO TUNED NOTES: Always input the frequency to the last digit. After performing DIRECT ACCESS and inputting the frequency, any discrepancy is corrected (for example, FM MHz = FM MHz), so the MEMORY button does not immediately function after the final digit has been input. To memorize a station frequency, first confirm that MEMORY is lit on the display before pressing the STATION CALL button. 11 En

12 PRESETTING STATIONS PRESET STATIONS 10 stations can be preset in each of the 3 classes, for a total of 30 station presets. MPX MODE 2 3 NOTES: You can also store MPX MODE and RF ATT settings in memory. If a station is memorized with the STATION CALL buttons at a position where a station is already memorized, the previous contents are erased and the new data is stored in memory. If preset stations get erased, repeat the preset procedures from the beginning. RF ATT 4 1. Tune in the desired station. For details concerning tuning, refer to BASIC TUN- ING OPERATIONS on P.10 and Press the MEMORY button. The MEMORY indicator will light for several seconds. Memory storage is not possible once the indicator goes off. In this case, press the MEMORY button again. If the button is pressed again while the indicator is lit up, the memory function will be canceled. 3. Select the desired class (A to C) with the CLASS button. 4. While the MEMORY indicator is lit, press the desired STATION CALL button. Pressing a STATION CALL button causes the MEMORY indicator to go out and the station to be preset. A station is preset (memorized) a few seconds after pressing the STATION CALL button. <Example> Presetting an FM MHz station into Class C with station no. (CH) MEMORY 3. CLASS Repeat procedure 1 to 4 to memorize other stations. 12 En

13 PRESETTING STATIONS PRESET STATION TUNING 1 MEMORY SCAN This function receives preset stations within a class (A, B or C) in order. While checking programs received, you can select the desired station Select the class number with the CLASS button. 2. Press the STATION CALL button to select the desired preset. NOTES: The contents of preset memory will be retained for several days, even if the tuner s power cord is unplugged. If a preset station has been erased, preset it again. 1. Press the CLASS button. Select the class you want to scan (A through C). 2. Press the MEMORY SCAN button. Scan starts. Each station is received for about 5 seconds. 3. When you find a desired station, press any button on the main unit (except the STANDBY/ON switch). 13 En

14 PRESETTING STATIONS MANUAL STATION NAME MEMORY Using up to 4 characters, you can store a name of your choice for preset FM/AM broadcast stations 1 to NOTES: If you perform no operations within about 5 seconds after INPUT is displayed, the display returns to frequency indications. Even if the station name contains less than four characters,always input a space and repeat steps 4 1 and 4 2. When you want to change a memorized station name, after selecting a desired broadcast station, register the new name using steps 2 to 4. For greater convenience, record memorized station names in the STATION CALL button memo on the next page Turn the STANDBY/ON switch ON. 2. Select the desired broadcast stations with the CLASS button and STATION CALL button. <Example> Inputting WEST as a station name in class B, station 1ch. 2. CLASS 3. Press the CHARACTER button once to select the station name input mode. INPUT lights in the display, and the mode switches to manual memory. 4. While INPUT is displayed, turn the TUNING knob clockwise or counterclockwise to input a desired character. Enter characters in the following way: 1The first character in the display changes while you turn the TUNING knob (see page 15). Select a character as desired. 2When you have selected your desired character, press the MEMORY button. This enters the first character and awaits input of the next character for memorization. Repeat this procedure until all four characters have been entered. 3. CHARACTER TUNING MEMORY 14 En

15 PRESETTING STATIONS When erasing a memorized station name, use the following procedure. 1Perform the steps 1 to 3 of "Manual Station Name Memory". 2While "INPUT" is displayed,turn the TUNING knob clockwise or counterclockwise to display a space. 3Press the MEMORY button.(one space is input.) 4Repeat the step 3 three more times to input four space. (The space lies between "@" and "A".) Character display used for station name input: Character A B C D E F G H I J K L M N O P Display indications Character Q R S T U V W X Y Z [ \ ] _! 0 1 Display indications Character " % & ' ( ) + * ` Display indications Character. / : Display indications NOTE: This unit converts lower case characters transmitted by broadcast station to upper case characters. STATION CALL button "memo" It is recommended that you make a note of the preset stations. STATION No. CLASS A Station Name Frequency CLASS B Station Name Frequency CLASS C Station Name Frequency 15 En

16 TROUBLESHOOTING Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work. Symptom Cause Remedy No power No sound Noise Sound distortion FM stereo broadcasts not received in stereo Has the power cord been disconnected? Have any of the output cords been disconnected or incorrectly connected? Has the antenna been disconnected or are the connections loose? Was the power cord unplugged for several days (preset station has been lost?) Are the signals weak and reception poor? Even though the signal is weak, the RF ATT is on. Is the station properly tuned in to the correct frequency? Has the antenna been disconnected or is the connection loose? Even though the signal is weak, the RF ATT is on. On the FM band The T-type FM antenna has not been extended,or it is not properly orientated. Are the signals weak and reception poor? Even though the signal is weak,the RF ATT is on. Static from other appliances (or automobiles) or multipath reflection (radio waves reflected off mountains and tall buildings,hence not received directly). On the AM band Poor positioning of the AM loop antenna. The supplied AM loop antenna is in contact with the unit. Are the signals weak and reception poor? Noise from other electrical appliances (fluorescent light/motors). Antenna input is insufficient because of weak broadcast signals. The unit is not correctly tuned to the frequency of the broadcast station. MPX MODE button is set to MONO. Reconnect the power cord. Connect them properly to the TUNER terminals on the amplifier. Connect the antenna properly. Preset the stations once again. Set the MPX MODE button to MONO (the broadcast will be received in monaural). Set the RF ATT to off. Tune in the station correctly. Connect the antenna properly. Set the RF ATT to off. Extend both ends fully,and face it in the direction giving the best reception. Replace the supplied T-type FM antenna with an outdoor antenna. Set the MPX MODE button to MONO (the broadcast will be received in monaural). Set the RF ATT to off. Try changing the antenna location. If you are using an outdoor antenna, move it away from the street. Change antenna direction, and set it in the position giving the best reception. Move the loop antenna away from the unit. Install and connect an external AM antenna and ground the unit. Turn off the noise-generating equipment, or move it away. Use a multi-element FM antenna. Tune in the correct frequency. Set MPX MODE button to AUTO. Abnormal functioning of this unit may be caused by static electricity, or other external interference. To restore normal operation, turn the power off and then on again, or unplug the AC power cord and then plug it in again. 16 En

17 SPECIFICATIONS FM tuner section Frequency Range MHz to 108 MHz Usable Sensitivity NORMAL... Mono: 13.2 dbf, IHF(1.3 µ V / 75 Ω) 50 db Quieting Sensitivity NORMAL... Mono: 20.2 dbf, IHF (2.8 µ V / 75 Ω) Stereo: 36.2 dbf, IHF (17.7 µ V / 75 Ω) Signal-to-Noise Ratio... Mono: 76 db (at 85 dbf) Stereo: 73 db (at 85 dbf) Distortion... Stereo: 0.5 % (1 khz) Alternate Channel Selectivity db (±400 khz) Stereo Separation db (1 khz) Frequency Response... ±1 db (30 Hz to 15 khz) Image Response Ratio db IF Response Ratio db Antenna Input Ω unbalanced AM tuner section Frequency Range khz to 1,602 khz (Step 9 khz) 530 khz to 1,700 khz (Step 10 khz) Sensitivity (IHF, Loop antenna) µ V / m Selectivity db(±9 khz) Signal-to-Noise Ratio db Image Response Ratio db IF Response Ratio db Antenna... Loop Antenna Audio section Output (Level/Impedance) FM (100 % MOD) mv / 1k Ω AM (30 % MOD) mv / 1k Ω Miscellaneous Power Requirements... AC 110/ /220/240 V (switchable), 50 / 60 Hz Power Consumption W Power Consumption in standby mode... 1 W Dimensions (W) x 78 (H) x 287 (D) mm Weight (without package) kg Furnished parts FM T-type antenna... 1 AM Loop antenna... 1 Audio cord... 1 Control cord... 1 Operating Instructions... 1 NOTE: Specifications and design are subject to possible modifications without notice, due to improvements. Published by Pioneer Corporation. Copyright 2004 Pioneer Corporation. All rights reserved. 17 En

18 TWO VOLTAGE SERECTORS 110V 240V V V V 220V D _ChH 18 Ch

19 19 Ch

20 20 Ch

21 GND INPUT PHONO CD TUNER L R ANTENNA TWO VOLTAGE SERECTORS FM UNBAL 75Ω AM LOOP ANTENNA L R OUTPUT CONTROL IN OUT V V 240V 110V 220V V Î CONTROL IN OUT CONTROL IN OUT CONTROL IN OUT CONTROL IN OUT FM UNBAL 75Ω ANTENNA AM LOOP ANTENNA 21 Ch

22 22 Ch

23 FM/AM DIGITAL-SYNTHESIZER TUNER X <? Î MEMORY CLASS DIRECT TUNING MODE TUNING STANDBY/ON MEMORY SCAN CHARACTER DISPLAY MODE RF ATT MPX MODE BAND /10 - =~! Ch

24 - ~! = 24 Ch

25 1 4 5 MEMORY AUTO RF ATT MONO STEREO TUNED Ch

26 26 Ch

27 DIRECT / / /10 STEREO TUNED 27 Ch

28 MEMORY CLASS 5 28 Ch

29 29 Ch

30 1 2 CLASS CHARACTER TUNING MEMORY 30 Ch

31 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ \ ] _! " % & ' ( ) + * `. / : Ch

32 32 Ch

33 µ µ µ µ Ch

34 Published by Pioneer Corporation. Copyright 2004 Pioneer Corporation. All rights reserved. K002_En <04C00001> 18 En Printed in Japan <ARE7342-A>