ULTRAWIDEBAND (UWB) communications have attracted

Transcription

1 294 IEEE ANTENNAS AND WIRELESS PROPAGATION LETTERS, VOL. 5, 2006 Circular and Elliptical CPW-Fed Slot and Microstrip-Fed Antennas for Ultrawideband Applications Evangelos S. Angelopoulos, Argiris Z. Anastopoulos, Dimitra I. Kaklamani, Member, IEEE, Antonis A. Alexandridis, Fotis Lazarakis, and Kostas Dangakis Abstract This letter presents novel circular and elliptical coplanar waveguide (CPW)-fed slot and mictrostip-fed antenna designs targeting the GHz band. The antennas are comprised of elliptical or circular stubs that excite similar-shaped slot apertures. Four prototypes have been examined, fabricated and experimentally tested, the three being fed by a CPW and the fourth by a microstrip line, exhibiting a very satisfactory behavior throughout the 7.5 GHz of the allocated bandwidth in terms of impedance matching (VSWR 2), radiation efficiency and radiation pattern characteristics. Measured impedance bandwidths of beyond 175% will be presented. Index Terms Circular, coplanar waveguide (CPW), elliptical, microstrip, slot, ultrawideband (UWB). I. INTRODUCTION ULTRAWIDEBAND (UWB) communications have attracted great interest lately, being one of the most promising technologies for short range mobile systems. UWB systems use short duration pulses of some subnanoseconds to transmit coded signals. The short duration of the pulse spreads the signal energy to a very wide bandwidth as indicated by the Fourier transform relationship. This feature combined with the low transmission energy ensures minimal interference with common narrowband systems. Because of its immunity to multipath fading, since it resolves reflections, the very low power requirements and the guaranteed high bit data rates, UWB technology seems adequate to numerous potential applications. To name a few: radars, ground penetration radars, through-the-wall or medical imaging, precision location systems and other military communications setups. In this letter, we investigate the properties of circular and elliptical configurations which meet the protocol requirements, in terms of impedance bandwidth, in the GHz band. Up to now, there has been a vivid stir of interest among antenna engineers in trying to develop novel UWB antenna designs operating throughout the entire 7.5 GHz Manuscript received February 14, 2006; revised May 26, This work has been partially funded by the E.U. in the framework of project IST , ACE (Antenna Center of Excellence). E. S. Angelopoulos, A. Z. Anastopoulos and D. I. Kaklamani are with the National Technical University of Athens, School of Electrical and Computer Engineering, Microwave and Fiber Optic Laboratory (MFOL), Athens GR-15780, Greece ( vagee@esd.ece.ntua.gr). A. A. Alexandridis, F. Lazarakis, and K. Dangakis are with the Institute of Informatics and Telecommunications, NCSR Demokritos, Athens GR-15310, Greece ( aalex@iit.demokritos.gr). Digital Object Identifier /LAWP Fig. 1. Geometry of the proposed CPW-fed slot antenna configuration. TABLE I DIMENSIONS OF THE FOUR ANTENNA PROTOTYPES (I, II, III, AND IV) ON e =3, h =1:575 mm spectrum. In [1] and [2], designs of single ended or differentially fed elliptical disc monopoles, and planar teardrop-like dipoles have successfully exhibited measured bandwidths of several gigahertz. Alternatively, by using CPW to feed circular monopoles [3], U-shaped stubs [4], or curved exotic configurations [5], UWB behavior has been equivalently demonstrated. In the current study, novel circular and elliptical slot antennas fed by 50 planar transmission lines (either CPW or microstrip) are examined. The first three configurations are CPW-fed slot antennas, where the coplanar transmission line is terminated to an elliptical or circular tuning stub which is included within a slot of same shape, etched from the ground plane. So far, a similar configuration with a rectangular stub [6] has been shown to exhibit 60% of impedance bandwidth with respect to the center frequency of 2 GHz. Here, we present measured impedance bandwidths of 175%. The fourth proposed radiator is a novel microstrip-fed elliptical stub which is excited over a similar /$ IEEE

2 ANGELOPOULOS et al.: CIRCULAR AND ELLIPTICAL CPW-FED SLOT AND MICROSTRIP-FED ANTENNAS 295 Fig. 2. Prototype IV. Microstrip-fed elliptical slot antenna geometry. shaped aperture ground plane. It comes as a direct modification of the CPW-fed designs and can be considered as an alternative UWB radiator for multisubstrate PCB boards, exhibiting a bandwidth ratio of 142%. Details of the simulation procedure and experimental results exhibiting the UWB characteristics of the proposed radiators are analyzed and discussed. II. ANTENNA DESCRIPTION A. Elliptical and Circular CPW-Fed Slot Designs A general design layout of the CPW-fed slot antenna is shown in Fig. 1. All developed prototypes are photochemically etched on a TLC 30 substrate of mm (h) of thickness and relative permittivity of 3 from Taconic. The ground plane dimensions are mm by mm and the metal cladding is mm. The and axes of the elliptical slot are denoted with and, respectively, while and are the axes of the stub tuning element. The coplanar line has a length of mm, while a strip width of mm and a feed aperture of mm, ensure characteristic input impedance of 50. The offset distance from the tuning stub (elliptical or circular) to the edge of the coplanar line is denoted as. The circular geometry arises when and. The design layout illustrated in Fig. 1 has been rigorously investigated using HFSS. For various values of,,, and, UWB behavior has been achieved. As indicated in [1], the distance from the antenna stub to the surrounding ground plane with respect to the feeding point, is symmetrically and gradually increasing. As a consequence, the impedance change from one resonant mode to another is small, therefore enabling very large bandwidth from the fundamental mode to much higher resonant modes. Consequently, apart from the optimal value settings of the stub s and slot s radii, (it controls the offset gap) has been specially arranged in order to satisfactorily arrange the depth of impedance matching, without sacrificing bandwidth. In all occasions was fixed to 0.3 mm. Three prototypes hereafter denoted as I, II, and III, were the product of the aforementioned simulation study. Their dimensions can be seen in Table I. Prototype I is an elliptical configuration, while Prototype II and III are circular configurations. Prototype III has been tuned to serve an even lower frequency range (starting from around 1 GHz), therefore having almost twice the size of the other CPW prototypes. Fig. 3. Measured versus simulated return loss of Prototype I, II, III, and IV. B. Microstrip-Fed Elliptical Slot Design The microstrip-fed module, henceforth denoted as Prototype IV, is derived from the elliptical configuration (I) simply by transferring the feeding network on the other side of the substrate, as can be seen in Fig. 2. We have chosen to feed the elliptical stub with a 50 Ohm impedance line mm,

3 296 IEEE ANTENNAS AND WIRELESS PROPAGATION LETTERS, VOL. 5, 2006 Fig. 4. H-plane (x-z plane) and E- plane (y-z plane) for Prototype I. (a) 3.4 GHz, (b) 6.8 GHz, and (c) 8.9 GHz. whereas the rest of the dimensions are kept the same with the CPW-fed elliptical model (see Table I). Here, the elliptical stub element implemented as the mictrostip line termination, offers more wideband behavior than the circular one. Furthermore, the two metallization layers used are very easy to construct in single or multi-substrate PCB boards, therefore making this module appropriate for direct integration with UWB circuitry. III. EXPERIMENTAL RESULTS AND DISCUSSION All prototypes where characterized in terms of impedance bandwidth and radiation characteristics. Fig. 3 presents the return loss measurements acquired with an HP8720C network analyzer in its full operational span (0 20 GHz). It should be noticed that the miniaturized CPW-fed modules (I and II) perform satisfactorily even beyond 20 GHz. In particular, the measured bandwidth of the elliptical configuration (Fig. 3I) covers almost GHz (spans from 2.65 GHz to 20 GHz), or 153%, with respect to the central frequency at GHz. Similarly, the circular module s impedance bandwidth (Fig. 1II) spans from 2.95 GHz to 20 GHz, exhibiting GHz or 148% of bandwidth ratio. Concerning the oversized Prototype III, the lower frequency of operation is 1.3 GHz, corresponding to a bandwidth Fig. 5. H-plane (x-z plane) and E- plane (y-z plane) for Prototype III. (a) 1.4 GHz, (b) 3.9 GHz, and (c) 8 GHz. ratio of 175% (see Fig. 3III). Finally, the novel microstrip-fed Prototype IV exhibits bandwidth of 142%, with respect to the central frequency of GHz (see Fig. 3IV). It should be noticed that the implemented modification of the feeding network, from CPW to microstrip, resulting in Prototype IV, does not affect the lower frequency of operation (see Fig. 3I & Fig. 3IV). It can be deduced that these types of radiators demonstrate approximately the impedance characteristics of a UWB monopole fed by a CPW, as has been already presented in [3]. In this case, the first resonance is controlled by the diameter of the tuning stub (or the equivalent diameter when referring to elliptical stubs). In the CPW-elliptical case, the first resonance at 3.4 GHz would have been generated by a circular monopole with diameter equal to 0.25 or mm. Here, the equivalent diameter of Prototype I lies between ( mm or 0.23 ) and ( mm or 0.31 ). The diameter of Prototype II corresponds approximately to the quarter wavelength at the first resonance at 3.2 GHz, since mm. In Prototype III, the diameter corresponds to 0.32 at the first resonance at 1.4 GHz, whereas in IV the equivalent value ranges

4 ANGELOPOULOS et al.: CIRCULAR AND ELLIPTICAL CPW-FED SLOT AND MICROSTRIP-FED ANTENNAS 297 between 0.22 and 0.26 for the first resonant frequency at 3.2 GHz. All Prototypes where characterized in a fully anechoic environment in both orthogonal planes. For the miniaturized modules, the frequencies of evaluation were dictated by the 2 first resonances of Prototype I, that is 3.4 GHz and 6.8 GHz and the upper frequency of operation of the network analyzer that was used (Agilent E8358A), which corresponds to 8.9 GHz. Prototype III was evaluated in the first distinct resonance at 1.4 GHz and arbitrarily at 3.9 GHz and 8 GHz. The gain patterns of Prototypes I, III and IV can be seen in Figs Obtained results for Prototype II were omitted, due to their resemblance with Prototype I. A very satisfactory agreement between simulation and measurement can be seen. All designs exhibit an omni-directional profile in lower frequencies for the x-z plane and bi-directional for the y-z plane. As the frequency increases, Prototype I and IV become more directive, but still bi-directional. Prototype III radiates either with strong side lobes (3.9 GHz) or with multiple lobes (8 GHz). Polarization purity can only be considered in the low frequency regime where the cross-to-co polarization ratio is marginally kept around 20 db, in contrast to higher frequencies, where cross-polarization is dominant, regarding x-z plane. Despite the different feeding mechanism, Prototypes I and IV appear to radiate with the same way as can be noted in Fig. 4 and Fig. 6. The maximum gain obtained from measurements is around 4.5 dbi. IV. CONCLUSION Four designs of CPW-fed and microstrip-fed circular and elliptical configurations have demonstrated UWB behavior in a very broad frequency range. By transforming the CPW feeding to microstrip, the UWB characteristics are preserved along with the radiation profile. The proposed methodology provides the engineer with a unique way to choose between the two mostly used feeding networks, and therefore adapt the radiator to any emerging system requirement. Fig. 6. H-plane (x-z plane) and E- plane (y-z plane) for Prototype IV. (a) 3.4 GHz, (b) 6.8 GHz, and (c) 8.9 GHz. REFERENCES [1] J. Powell and A. Chandrakasan, Differential and single ended elliptical antennas for Ghz ultra wideband communication, in Proc. IEEE Antennas Propag. Symp., Monterey, CA, Jun [2] S.-Y. Suh, W. Stutzman, W. Davis, A. Waltho, and J. Schiffer, A novel broadband antenna, the low profile dipole planar inverted cone antenna (LPdiPICA), in Proc. IEEE Antennas Propag. Soc. Symp., vol. 1, Jun. 2004, pp [3] J. Liang, L. Guo, C. C. Chiau, and X. Chen, CPW-fed circular disc monopole antenna for UWB applications, in Proc. IEEE Int. Workshop Antenna Technol. (IWAT): Small Antennas Novel Metamater., Marina Mandarin, Singapore, Mar. 7 9, [4] R. Chair, A. A. Kishk, and K. F. Lee, Ultrawide-band coplanar waveguide-fed rectangular slot antenna, IEEE Antennas Wireless Propag. Lett., vol. 3, pp , [5] J. W. McCorkle, Electrically Small Planar UWB Antenna Apparatus and Related System, US B1, Jun. 23, [6] H.-D. Chen, Broadband CPW fed square slot antennas with a widened tuning stub, IEEE Trans. Antennas Propag., vol. 51, no. 8, pp , Aug

5 易迪拓培训 专注于微波 射频 天线设计人才的培养网址 : 射频和天线设计培训课程推荐 易迪拓培训 ( 由数名来自于研发第一线的资深工程师发起成立, 致力并专注于微波 射频 天线设计研发人才的培养 ; 我们于 2006 年整合合并微波 EDA 网 ( 现已发展成为国内最大的微波射频和天线设计人才培养基地, 成功推出多套微波射频以及天线设计经典培训课程和 ADS HFSS 等专业软件使用培训课程, 广受客户好评 ; 并先后与人民邮电出版社 电子工业出版社合作出版了多本专业图书, 帮助数万名工程师提升了专业技术能力 客户遍布中兴通讯 研通高频 埃威航电 国人通信等多家国内知名公司, 以及台湾工业技术研究院 永业科技 全一电子等多家台湾地区企业 易迪拓培训课程列表 : 射频工程师养成培训课程套装该套装精选了射频专业基础培训课程 射频仿真设计培训课程和射频电路测量培训课程三个类别共 30 门视频培训课程和 3 本图书教材 ; 旨在引领学员全面学习一个射频工程师需要熟悉 理解和掌握的专业知识和研发设计能力 通过套装的学习, 能够让学员完全达到和胜任一个合格的射频工程师的要求 课程网址 : ADS 学习培训课程套装该套装是迄今国内最全面 最权威的 ADS 培训教程, 共包含 10 门 ADS 学习培训课程 课程是由具有多年 ADS 使用经验的微波射频与通信系统设计领域资深专家讲解, 并多结合设计实例, 由浅入深 详细而又全面地讲解了 ADS 在微波射频电路设计 通信系统设计和电磁仿真设计方面的内容 能让您在最短的时间内学会使用 ADS, 迅速提升个人技术能力, 把 ADS 真正应用到实际研发工作中去, 成为 ADS 设计专家... 课程网址 : HFSS 学习培训课程套装该套课程套装包含了本站全部 HFSS 培训课程, 是迄今国内最全面 最专业的 HFSS 培训教程套装, 可以帮助您从零开始, 全面深入学习 HFSS 的各项功能和在多个方面的工程应用 购买套装, 更可超值赠送 3 个月免费学习答疑, 随时解答您学习过程中遇到的棘手问题, 让您的 HFSS 学习更加轻松顺畅 课程网址 : `

6 易迪拓培训 专注于微波 射频 天线设计人才的培养网址 : CST 学习培训课程套装该培训套装由易迪拓培训联合微波 EDA 网共同推出, 是最全面 系统 专业的 CST 微波工作室培训课程套装, 所有课程都由经验丰富的专家授课, 视频教学, 可以帮助您从零开始, 全面系统地学习 CST 微波工作的各项功能及其在微波射频 天线设计等领域的设计应用 且购买该套装, 还可超值赠送 3 个月免费学习答疑 课程网址 : HFSS 天线设计培训课程套装套装包含 6 门视频课程和 1 本图书, 课程从基础讲起, 内容由浅入深, 理论介绍和实际操作讲解相结合, 全面系统的讲解了 HFSS 天线设计的全过程 是国内最全面 最专业的 HFSS 天线设计课程, 可以帮助您快速学习掌握如何使用 HFSS 设计天线, 让天线设计不再难 课程网址 : MHz NFC/RFID 线圈天线设计培训课程套装套装包含 4 门视频培训课程, 培训将 13.56MHz 线圈天线设计原理和仿真设计实践相结合, 全面系统地讲解了 13.56MHz 线圈天线的工作原理 设计方法 设计考量以及使用 HFSS 和 CST 仿真分析线圈天线的具体操作, 同时还介绍了 13.56MHz 线圈天线匹配电路的设计和调试 通过该套课程的学习, 可以帮助您快速学习掌握 13.56MHz 线圈天线及其匹配电路的原理 设计和调试 详情浏览 : 我们的课程优势 : 成立于 2004 年,10 多年丰富的行业经验, 一直致力并专注于微波射频和天线设计工程师的培养, 更了解该行业对人才的要求 经验丰富的一线资深工程师讲授, 结合实际工程案例, 直观 实用 易学 联系我们 : 易迪拓培训官网 : 微波 EDA 网 : 官方淘宝店 : 专注于微波 射频 天线设计人才的培养易迪拓培训官方网址 : 淘宝网店 :