Description. Features. Continuous BA Series BB Series Units Steady State Applied Voltage: AC Voltage Range (V M(AC)RMS
|
|
- Erik Paul
- 5 years ago
- Views:
Transcription
1 BA/BB Varistor Series RoHS Description The BA and transient surge suppressors are heavy-duty industrial Metal-Oxide Varistors (MOVs) designed to provide surge protection for motor controls and power supplies used in oil-drilling, mining, transportation equipment and other heavy industrial A line applications. Agency Approvals Agency Agency Approval Agency File Number UL1449 E for only. These varistors have similar package construction but differ in size and ratings. The BA models are rated from 130 to 880V M(A). The BB models from 10 to 2800V M(A). Both the BA and feature improved creep and strike capability to minimize breakdown along the package surface, a package design that provides complete electrical isolation of the disc subassembly, and rigid terminals to ensure secure wire contacts. See BA/ Device Ratings and Specifications Table for part number and brand information. Additional Information Features Datasheet Resources Samples High energy absorption capability W TM 30J,000J Wide operating voltage range V M(A)RMS 130V to 880V 10V to 2800V Rigid terminals for secure wire contact ase design provides complete electrical isolation of disc subassembly Littelfuse largest packaged disc 60mm diameter No derating up to 85º ambient RoHS compliant Absolute Maximum Ratings For ratings of individual members of a series, see Device Ratings and Specifications chart ontinuous Units Steady State Applied Voltage: A Voltage Range (V M(A)RMS ) 130 to to 2800 V D Voltage Range (V M(D) ) 175 to to 30 V Transients: Peak Pulse urrent (I TM ) For 8/µs urrent Wave (See Figure 2),000 to 70,000 70,000 A Single Pulse Energy Range For 2ms urrent Squarewave (W TM ) 4 to to 000 J Operating Ambient Temperature Range (T A ) -55 to to +85 O Storage Temperature Range (T STG ) -55 to to +125 O Temperature oefficient (a V ) of lamping Voltage (V ) at Specified Test urrent <0.01 <0.01 %/ O Hi-Pot Encapsulation (OATING Isolation Voltage apability) (Dielectric must withstand indicated D voltage for one minute per MIL STD 2, Method 301) V OATING Insulation Resistance MΩ AUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
2 BA/ Ratings & Specifications Maximum Rating (85 ) Specifications (25 ) Part Number ontinuous V RMS V D Energy (2ms) Transient Peak urrent 8 x µs Varistor Voltage at 1mA D Test urrent Maximum lamping Volt V at 0A urrent (8/µs) Typical apacitance f = 1MHz V M(A) V M(D) W TM I TM Min V N(D) Max V (V) (V) (J) (A) (V) (V) (V) (V) (pf) V131BA V151BA V251BA V271BA V321BA V421BA V481BA V511BA V571BA V661BA V751BA V881BA V112BB V142BB V172BB V2BB V242BB V282BB NOTE: Average power dissipation of transients not to exceed 2.5W. See Figures 3 and 4 for more information on power dissipation.
3 Power Dissipation Ratings Peak Pulse urrent Test Waveform PERENT OF RATED VALUE AMBIENT TEMPERATURE ( o ) Figure 1 Figure 2 FIGURE 1. URRENT, ENERGY AND POWER DERATING URVE Should transients occur in rapid succession, the average power dissipation required is simply the energy (watt-seconds) per pulse times the number of pulses per second. The power so developed must be within the specifications shown on the Device Ratings and haracteristics Table for the specific device. Furthermore, the operating values need to be derated at high temperatures as shown in the above diagram. Because varistors can only dissipate a relatively small amount of average power they are, therefore, not suitable for repetitive applications that involve substantial amounts of average power dissipation. PERENT OF PEAK VALUE 0 90 O 1 T T 1 T 2 TIME 0 1 = Virtual Origin of Wave T = Time from % to 90% of Peak T 1 = Rise Time = 1.25 x T T 2 = Decay Time Example - For an 8/ µs urrent Waveform: 8µs = T 1 = Rise Time µs = T 2 = Decay Time O 1 = Virtual Origin of T = Time From % T 1 = Virtual Front Tim T 2 = Virtual Time to H Example: For an 8/ s 8 s = T 1 = Virtual Fron s = T 2 = Virtual Time FIGURE 2. PEAK PULSE URRENT TEST WAVEF Stand by Power Dissipation vs Applied V Rms at Varied Temperatures Typical Stability of Standby Power Dissipation at Rated V RMS vs Time POWER DISSIPATION (W) PER kv OF RATED V RMS TYPIAL TEMPERATURE OEFFIIENT OF POWER DISSIPATION = 2.2%/ o MAX AT T A = 85 o MAX AT T A = 25 o TYP AT T A = 25 o HOURS, T A = 85 o PERENTAGE OF MAXIMUM RATED V RMS (%) TIME AT RATED V RMS (HOURS) Figure 3 Figure 4 FIGURE 3. STANDBY POWER DISSIPATION vs APPLIED FIGURE 4. TYPIAL STABILITY OF STANDBY POWER V RMS AT VARIED TEMPERATURES DISSIPATION AT RATED V RMS vs TIME POWER DISSIPATION (W) PER kv OF RATED V RMS
4 Maximum lamping Voltage V131BA60 - V881BA60 Maximum lamping Voltage V112BB60 - V282BB60 MAXIMUM PEAK VOLTS (V) 6,000 4,000 3, MAX LAMPING VOLTAGE 130 TO 880V M(A) RATING T A = -55 o TO 85 o V881BA60 V751BA60 V661BA60 V571BA60 V321BA60 V271BA60 V251BA60 V151BA60 V131BA60 V511BA60 V481BA60 V421BA60 30,000,000,000 9,000 8,000 7,000 6,000 V282BB60 V242BB60 4,000 V2BB60 V172BB60 3,000 V142BB60 V112BB PEAK AMPERES (A) PEAK AMPERES (A) Figure 5 Figure 6 FIGURE 5. LAMPING VOLTAGE FOR V131BA60 - V881BA60 FIGURE 6. LAMPING VOLTAGE FOR V112BB60 - V282BB60 MAX PEAK VOLTS (V) MAX LAMPING VOLTAGE 10 TO 2800V M(A) RATING T A = -55 o TO 85 o Repetitive Surge apability Repetitive Surge apability,000 0, ,000,000 2,000,000 2, INDEFINITE INDEFINITE 0,000 0,000 Figure 7 IMPULSE DURATION (μs) Figure 8 IMPULSE DURATION (μs) FIGURE 7. SURGE URRENT RATING URVES FOR FIGURE 8. SURGE URRENT RATING URVES FOR NOTE: If pulse ratings are exceeded, a shift of V N (D) (at specified current) of more than +/-% could result.this type of shift, which normally results in a decrease of V N (D), may result in the device not meeting the original published specifications, but it does not prevent the device from continuing to function, and to provide ample protection. SURGE URRENT (A) SURGE URRENT (A) Physical Specifications Environmental Specifications Lead Material BA / BB opper with Tin Plating Operating Temperature -55 to +85 Insulating Material Device Labeling ured, flame retardant epoxy polymer meets UL94V 0 requirements. Marked with LF, Part Number and Date code Storage Temperature Humidity Aging Thermal Shock -55 to , 85% RH, 00 hours +/- 5% typical resistance change +85 to -40 times +/- 5% typical resistance change Solvent Resistance MIL STD 2, Method 215 Moisture Sensitivity Level 1, J-STD-0
5 Metal-Oxide PAN HEAD SLOTTED SREW Varistors (MOVs) (1.752).5 Dimensions 0 (3.94) 40±2 (1.575 ± 0.08) M6 INTERNATIONAL THREAD PAN HEAD SLOTTED SREW 23.5 (0.925) 79±3 (3.11±0.12) 95 (3.74) MAX 0 (3.94) 6 (0.24) PAN HEAD SLOTTED SREW 86±2 (3.38±0.08).5 0 (3.94) Notes: Typical weight: :2g and : 600g Dimensions are in mm; inches in parentheses for reference only (1.752) 0 (3.94) Part Numbering System V XX X BA60 40±2 (1.575 ± 0.08) M6 INTERNATIONAL THREAD VARISTOR V M(A) First Two Significant Digits* DIS SIZE (60mm) SERIES DESIGNATOR BA or BB 79±3 (3.11±0.12) 95 (3.74) MAX V M(A) Decade Multiplier* (1 or 2) 6 (0.24) *Refer to Rating & Specifications table Examples: 130 VM(A) = VM(A) = ±2 (3.38±0.08) 0 (3.94)
Samples. Continuous MA Series Units Steady State Applied Voltage: AC Voltage Range (V M(AC)RMS. ) 9 to 264 V DC Voltage Range (V M(DC)
Axial ead / Application Specific Varistors > MA Series MA Varistor Series RoHS Description The MA Series of transient surge suppressors are axial lead Metal Oxide Varistors (MOVs) for use in a wide variety
More informationContinuous C-III Series Units. ) 2ms Rectangular Wave 40 to 530 J Operating Ambient Temperature Range (T A
RoHS Description The C-III Series of Metal-Oxide Varistors (MOVs) are specifically designed for applications requiring high surge energy absorption ratings and superior multiple pulse absorption rating.
More informationMetal-Oxide Varistors (MOVs) Radial Lead Varistors > TMOV 25S Varistor Series
TMOV 25S Varistor Series RoHS Description Metal Oxide Varistors (MOVs) are rated for specific AC line operating voltages, and exceeding these limits through the application of a sustained abnormal over-voltage
More informationMetal-Oxide Varistors (MOVs) Thermally Protected Varistors > SMOV 25S Varistor Series
S25S Varistor Series RoHS Description The Littelfuse S 25S thermally protected varistor is a self-protected device. It consists of a 25mm square varistor with an integral thermal designed to open in the
More informationVaristor Products Radial Lead Varistors > LA Series
RoHS Agency Approvals Agency Agency File Number 7596, 5659, 3 Description The of transient voltage surge suppressors are radial leaded varistors (MOVs) that are designed to be operated continuously across
More informationVaristor Products Radial Lead Varistors > ZA Series
RoHS Description The of transient voltage surge suppressors are radial leaded varistors (MOVs) designed for use in the protection of low and medium-voltage circuits and systems. Typical applications include
More informationTVS Diode Arrays (SPA Diodes) SP725 Series 5pF 8kV Diode Array. General Purpose ESD Protection - SP725 Series. RoHS Pb GREEN.
SP725 Series 5pF 8kV Diode Array RoHS Pb GREEN Description The SP725 is an array of SR/Diode bipolar structures for ESD and overvoltage protection of sensitive input circuits. The SP725 has 2 protection
More informationTVS Diode Arrays (SPA Diodes) SP725 Series 5pF 8kV Diode Array. General Purpose ESD Protection - SP725 Series. RoHS Pb GREEN.
SP725 Series 5pF 8kV Diode Array RoHS Pb GREEN Description The SP725 is an array of SR/Diode bipolar structures for ESD and overvoltage protection of sensitive input circuits. The SP725 has 2 protection
More information50W TO220 High Power Resistors
50W TO220 High Power Resistors MHP 50 Non-inductive, thin film technology. Thermally enhanced Industry standard TO220 package. RoHS compliant. Low thermal resistance, 2.3 C/W resistor hot spot to metal
More informationMetal Oxide Varistors
Straight Lead Dimensions Table Series 5D 7D 10D 14D 20D D max 7 9.5 14 17.5 24 d* 0.6 0.6 0.8 0.8 1 W** 5 5 7.5 7.5 10 H max 12.5 14.5 20 22.5 29.5 H1 max 10 12 17 20.5 28 T max 4.9 4.9 8.5 8.5 9 P max
More informationP6SMB11AT3G Series. TVS Diodes. Surface Mount > 600W > P6SMB11AT3G Series. Bi-directional. Cathode. Anode. Uni-directional.
P6SMB11AT3G Series Pb Description The P6SMB11AT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge
More informationSamples. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 100 C 40 A I T(AV) Average on-state current T C
Sxx40x Series RoHS Description Excellent unidirectional switches for phase control applications such as heating and motor speed controls. Standard phase control SCRs are triggered with few milliamperes
More information6600W, 10V 43V Surface Mount Transient Voltage Suppressor
66W, 1V 43V Surface Mount Transient Voltage Suppressor FEATURES AEC-Q11 qualified Junction passivation optimized design technology T J =175 C capability suitable for high reliability and automotive requirement
More informationFMMT491Q. Mechanical Data. Description. Feature. Ordering Information (Notes 4 & 5) Marking Information 60V NPN MEDIUM POWER TRANSISTOR IN SOT23
60V NPN MEDIUM POWER TRANSISTOR IN Description Mechanical Data This Bipolar Junction Transistor (BJT) is designed to meet the stringent requirements of Automotive Applications. Feature BV EO > 60V = 1A
More informationP6SMB6.8AT3G Series, SZP6SMB6.8AT3G Series. 600 Watt Peak Power Zener Transient Voltage Suppressors. Unidirectional*
P66.8AT3G Series, SZP66.8AT3G Series 600 Watt Peak Power Zener Transient Voltage Suppressors Unidirectional* The series is designed to protect voltage sensitive components from high voltage, high energy
More information15,000 Watt Transient Voltage Suppressor (TVS) Protection Device
Compliant 15,000 Watt Transient Voltage Suppressor (TVS) Protection Device DESCRIPTION This device clamps dangerous high-voltage short-term transients such as those produced by the secondary effects of
More informationTeccor brand Thyristors 4 / 6 / 8 / 10 / 15 Amp Quadracs
QxxxxLTx Series RoHS Description The Quadrac is an internally triggered Triac designed for AC switching and phase control applications. It is a Triac and DIAC in a single package, which saves user expense
More informationMAC12HCDG, MAC12HCMG, MAC12HCNG
MAC2HCDG, MAC2HCMG, MAC2HCNG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls or dimmers; or wherever full wave, silicon gate controlled
More informationTVS Diode Arrays (SPA Diodes) SP723 Series 5pF 8kV Diode Array. General Purpose ESD Protection - SP723 Series. RoHS Pb GREEN.
SP723 Series 5pF 8kV Diode Array RoHS Pb GREEN Description The SP723 is an array of SR/Diode bipolar structures for ESD and over-voltage protection of sensitive input circuits. The SP723 has 2 protection
More informationDescription. Features & Benefits. RoHS compliant Glass passivated junctions. Applications. Additional Information. Datasheet
Sx01E & SxN1 Series RoHS Description Excellent for lower current heat, lamp, and audible alarm controls for home goods. Standard phase control SCRs are triggered with few milliamperes of current at less
More information1SMA5.0AT3G Series. TVS Diodes. Surface Mount > 400W > 1SMA5.0AT3G Series. Bi-directional. Cathode. Anode. Uni-directional.
SMA5.0AT3G Series Pb Description The SMA5.0AT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge
More informationGreen. Bottom View. Top View. Part Number Qualification Case Packaging SMCJXX(C)AQ-13-F* Automotive SMC 3000/Tape & Reel
Green J14()AQ J36()AQ 1,500W SURFAE MOUNT AUTOMOTIVE TRANSIENT VOLTAGE SUPPRESSOR Product Summary (@T A = +25 ) P PK I FSM (A) V RWM (V) PM (AV) 1500W 200 14-36 5W Features and Benefits 1500W Peak Pulse
More information200W, 5V - 100V Surface Mount Transient Voltage Suppressor
200W, 5V - 100V Surface Mount Transient Voltage Suppressor FEATURES Photo Glass passivated junction Low power loss, high efficiency Ideal for automated placement Excellent clamping capability Typical I
More informationMCR218-2G, MCR218-4G, MCR218-6G
MCR218-2G, MCR218-4G, MCR218-6G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half-wave silicon gate-controlled,
More informationDescription. Features. As low as 8mA max holding current. UL Recognized TO- 220AB package. 110 C rated junction temperature
Q612LTH1LED Series RoHS Agency Approval Agency Agency File Number Description The Quadrac is an internally triggered Triac designed for AC switching and phase control applications. It is a Triac and DIAC
More informationTeccor brand Thyristors 40 Amp Low T q SCR. Symbol Parameter Test Conditions Value Unit RMS on-state current T C = 100 C 40 A I T(AV)
RoHS Description The S4040xQx series of s offer fast turn-off time (tq) characteristics required for applications such as power inverters, switching regulator, and high frequency pulse circuits. These
More information15,000 Watt Transient Voltage Suppressor (TVS) Protection Device
M1KP22A M1KP280CA(e3) Available 1,000 Watt Transient Voltage Suppressor (TVS) Protection Device DESCRIPTION This Transient Voltage Suppressor series of M1KP22A M1KP280CA offers an extended voltage range
More informationC122F1G. Thyristors. Surface Mount 50V > C122F1G. Description
Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More informationP6KE. Transil, transient voltage surge suppressor (TVS) Features. Description. Complies with the following standards
Transil, transient voltage surge suppressor (TVS) Datasheet production data Features Peak pulse power: 600 W (10/0 µs ) Stand-off voltage range 6.8 to 440 V Unidirectional and bidirectional types Low clamping
More information5V 48V Small Footprint, Surface Mount Transient Voltage Suppressors
Available 5V 48V Small Footprint, Surface Mount Transient Voltage Suppressors DESCRIPTION Microsemi s unique and new Powermite UPT series of transient voltage suppressors feature oxidepassivated chips
More informationB170BQ - B1100BQ. Features and Benefits. Product Summary C) Mechanical Data. Applications. Ordering Information (Note 5) Marking Information
Green 1.0A HIGH VOLTAGE SHOTTKY BARRIER RETIFIER Product Summary (@+25 ) B170BQ B180BQ B190BQ 70 1.0 0.79 0.5 80 1.0 0.79 0.5 90 1.0 0.79 0.5 B10BQ 0 1.0 0.79 0.5 Features and Benefits Guard Ring Die onstruction
More information1.5SMC6.8AT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMC6.8AT3G. Bi-directional. Cathode. Anode. Uni-directional. Description
1.5SMC6.8AT3G Pb Description The 1.5SMC6.8AT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge
More informationMCR08B, MCR08M. Thyristors. Surface Mount 600V - 800V > MCR08B, MCR08M G K. Description
MCR8B, MCR8M Pb Description PNPN devices designed for line powered consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection
More informationFeatures. Symbol Parameters Test Conditions Min Max Unit V T. TA=25 C Pulse Wave = 10μs, Sine Wave, f=120hz K2201GL 230 V BO K2401GL K2401GL
Standard Bidirectional SIDACs Kxxx1GL Series RoHS Description Schematic Symbol The Multipulse SIDAC is a voltage switch used in Metal- Halide lamp ignition circuits, as well as High Pressure Sodium lamp
More informationQJxx16xHx Series. Thyristors 16 Amp High Temperature Alternistor Triacs. RoHS. Description
RoHS Description This 16A high temperature alternistor triac solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More informationBC817-16Q /-40Q. Mechanical Data. Description. Features. Ordering Information (Notes 4 and 5) Marking Information
45V NPN SMALL SIGNAL TRANSISTOR IN Description Mechanical Data This Bipolar Junction Transistor (BJT) is designed to meet the stringent requirements of Automotive Applications. Features BV EO > 45V I =.5A
More informationMAC16DG, MAC16MG, MAC16NG
MAC6DG, MAC6MG, MAC6NG Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking Voltage to 800
More informationTeccor brand Thyristors EV Series 0.8 Amp Sensitive Triacs
LX8 Series RoHS Description New 0.8 Amp bi-directional solid state switch series offering direct interface to microprocessor drivers in economical TO-92 and surface mount packages. The die voltage blocking
More informationTop View Device Symbol Top View Pin-Out
YWW NEW PRODUT 500V PNP HIGH PERFORMANE TRANSISTOR IN Features BV EO > -500V I = -150mA High ontinuous urrent I M = -500mA Peak Pulse urrent Totally Lead-Free & Fully RoHS ompliant (Notes 1 & 2) Halogen
More informationFeatures. Samples. Symbol Parameter Value Unit TO-92 SOT-223. t p TO-92 SOT-223. = 2 x I GT. Peak gate current t p. = 10 μs T J
L01 Series RoHS Description New 1 Amp bi-directional solid state switch series offering direct interface to microprocessor drivers in economical TO-92 and surface mount packages. The die voltage blocking
More informationTeccor brand Thyristors High Energy Bidirectional SIDACs
Kxxx0yH Series RoHS Description The new Kxxx0yH is a higher energy SIDAC switch for gas ignition applications requiring higher current pulse current especially at low repetition rate. It is offered in
More informationGreen. PowerDI123. Top View. Part Number Compliance Case Packaging DFLS260Q-7 Automotive PowerDI /Tape & Reel
Green 2.A SURFAE MOUNT SHOTTKY BARRIER RETIFIER POWERDI 123 Product Summary V R (V) I F (A) V F MAX (V) @ +25 I R MAX (ma) @ +25 6 2..62.1 Description and Applications This Schottky Barrier Rectifier has
More informationDescription. Features. As low as 8mA max holding current. UL Recognized TO- 220AB package. 110 C rated junction temperature
Q6012xH1LED Series RoHS Description Q6012LH1LED series is designed to meet low load current characteristics typical in LED lighting applications. By keeping holding current at 8mA maximum, this Triac series
More informationDZTA42. Features. Mechanical Data. Applications. Ordering Information (Note 4) Marking Information 300V NPN HIGH VOLTAGE TRANSISTOR IN SOT223 DZTA42
3V NPN HIGH VOLTAGE TRANSISTOR IN Features BV EO > 3V I = 5mA High ollector urrent 2W Power Dissipation Low Saturation Voltage V E(sat) < 5mV @ 2mA omplementary PNP Type: DZTA92 Totally Lead-Free & Fully
More informationMCR8DCM, MCR8DCN. Thyristors. Surface Mount 600V - 800V > MCR8DCM, MCR8DCN G K. Description
MCR8DCM, MCR8DCN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More informationTeccor brand Thyristors 12 Amp Standard SCR. Symbol Parameter Test Conditions SRR6012x1 Unit I T(RMS) RMS on-state current T C
RoHS Description Excellent unidirectional switches for phase control and general switching applications such as heating, motor control controls, converters / rectifiers and capacitive discharge ignitions.
More informationThyristors 12 Amp Alternistor (High Communitation) Triacs
Qxx12xHx Series RoHS Description This 12 Amp bidirectional solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls,
More informationMCR8DSM, MCR8DSN. Thyristors. Surface Mount 600V - 800V > MCR8DSM, MCR8DSN G K. Description
MCR8DSM, MCR8DSN Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Small Size
More informationMSP5.0A. Surface Mount TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. New Product
MSP5.A Surface Mount TRANSZORB Transient Voltage Suppressors esmp TM Series Top View Bottom View MicroSMP PRIMARY CHARACTERISTICS V WM 5. V P PPM W I FSM 25 A T J max. 5 C FEATURES Very low profile - typical
More informationSP721 Series 3pF 4kV Diode Array
SP7 Series 3pF 4kV Diode Array RoHS Pb GREEN Description Pinout SP7 (PDIP, SOI) TOP VIEW Functional Block Diagram V+ V- 4 8 V- 3 4 3, 5-7 8 7 6 5 V+ The SP7 is an array of SR/Diode bipolar structures for
More informationMCR8NG. Thyristors. Surface Mount 600V - 800V > MCR8NG. Description
Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled devices are needed.
More informationBTA25-600CW3G, BTA25-800CW3G
BTA25-600CW3G, BTA25-800CW3G Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Blocking oltage
More informationMAC8DG, MAC8MG, MAC8NG
MAC8DG, MAC8MG, MAC8NG Pb Description Designed primarily for full-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled,
More informationDistributed by: www.jameco.com 1-8-831-4242 The content and copyrights of the attached material are the property of its owner. P6KE6V8(C)A - P6KE4(C)A 6W TRANSIENT VOLTAGE SUPPRESSOR Features 6W Peak Pulse
More informationP C = 100 C Power Dissipation Linear Derating Factor
PDP TRENH IGBT PD - 97132 IRGP486PbF Features l Advanced Trench IGBT Technology l Optimized for Sustain and Energy Recovery ircuits in PDP Applications l Low V E(on) and Energy per Pulse (E PULSE TM )
More informationTeccor brand Thyristors Silicon Controlled Rectifiers
Sx02xS EV Series Amp Sensitive SCR Description New Amp sensitive gate SCR series offers high static dv/dt with low turn off time (tq) through small die planar construction design. All SCR s junctions are
More informationMSP3V3, MSP5.0A. Surface Mount TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES. Series.
Surface Mount TRANSZORB Transient Voltage Suppressors esmp Series Top View Bottom View PRIMARY CHARACTERISTICS V WM 3.3 V to 5. V V BR 4.1 V to 7.7 V P PPM 15 W T J max. 15 C Polarity Uni-directional Package
More informationATV66SM836A-G. SMD Transient Voltage Suppressor. Working Voltage: 36 Volts Peak Pulse Power: 6600 Watts RoHS Device. Features.
orking Voltage: 36 Volts Peak Pulse Power: 66 atts RoHS Device eatures -Glass passivated chip. -66 peak pulse power capability with a 1/µs waveform, repetitive rate (duty cycle):.1% -Meets ISO7637-2 5a
More information1.5SMCxxAT3G. TVS Diodes. Surface Mount > 1500W > 1.5SMCxxAT3G. Cathode. Anode. Uni-directional. Description
1.5SMCxxAT3G Pb Description The 1.5SMCxxAT3G series is designed to protect voltage sensitive components from high voltage, high energy transients. They have excellent clamping capability, high surge capability,
More informationIRGBC20KD2-S PD Short Circuit Rated UltraFast CoPack IGBT INSULATED GATE BIPOLAR TRANSISTOR WITH ULTRAFAST SOFT RECOVERY DIODE
INSULATED GATE BIPOLAR TRANSISTOR WITH ULTRAFAST SOFT REOVERY DIODE Features Short circuit rated -µs @25, V GE = 5V Switching-loss rating includes all "tail" losses HEXFRED TM soft ultrafast diodes Optimized
More information-2.7A. Pin Out - Top View
6V P-HANNEL ENHANEMENT MODE MOSFET Product Summary Features and Benefits ADVANE INFORMATION NEW PRODUT V (BR)DSS -6V Description R DS(on) I D T A = +25 5mΩ @ V GS = -V -3A 85mΩ @ V GS = -4.5V -2.7A This
More informationTVS Diode Arrays (SPA Diodes) SP720 Series 3pF 4kV Diode Array. General Purpose ESD Protection - SP720 Series. RoHS Pb GREEN.
SP7 Series pf 4kV Diode Array RoHS Pb GREEN Description The SP7 is an array of SR/Diode bipolar structures for ESD and over-voltage protection to sensitive input circuits. The SP7 has protection SR/Diode
More informationPOST REFLOW HEIGHT DIMENSIONS
MEDER electronic RM Series 4 input / 2 output DESRIPTION The RM05-4A-S-4/2 and RM05-2A2B-S-4/2 are low-profile 4 input / 2 output Relay Modules with an FR-4 substrate and rugged thermoset epoxy overmold.
More informationTransient Voltage Suppression Diodes. Surface Mount 400W > P4SMA series. Features. less than 1μA when V BR. Applications. Additional Infomarion
P4SMA Series RoHS Pb e3 Uni-directional Bi-directional Description The P4SMA series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other
More informationFeatures. Symbol Parameter Value Unit TO-92 SOT-223. t p TO-92 SOT-223. Peak gate current t p. = 10 μs T J
Sx02xS Series RoHS Description New mp sensitive gate SCR series offers high static dv/dt with low turn off time (tq) through small die planar construction design. ll SCR s junctions are glasspassivated
More informationTeccor brand Thyristors Standard Bidirectional DIAC Trigger
Description The HTM, HT, and ST series of bilateral trigger DIACs offer a range of voltage characteristics from 27V to 70V. A DIAC semiconductor is a full-wave or bidirectional Thyristor. It is triggered
More information200W, 5V - 100V Surface Mount Transient Voltage Suppressor
200W, 5V - 100V Surface Mount Transient Voltage Suppressor FEATURES Photo Glass passivated junction Low power loss, high efficiency Ideal for automated placement Excellent clamping capability Typical I
More informationTECHNICAL SPECIFICATIONS OF SILICON RECTIFIER
TECHNICAL SPECIFICATIONS OF SILICON RECTIFIER VOLTAGE RANGE 5 to 1 CURRENT 1. Ampere FEATURES * Low cost * Low leakage * Low forward voltage drop * High current capability DO 41 MECHANICAL DATA * Case:
More informationMAC08BT1, MAC08MT1. Thyristors. Surface Mount 200V - 600V > MAC08BT1, MAC08MT1. Description
MAC08BT1, MAC08 Pb Description Designed for high volume, low cost, industrial and consumer applications such as motor control; process control; temperature, light and speed control. Features Sensitive
More informationSD Series 450W Discrete Unidirectional TVS Diode
General Purpose ESD Protection - 5W Discrete Unidirectional TVS Diode RoHS Pb GREEN Description The SD series is designed to replace multilayer varistors (MLVs) in electronic equipment for low speed and
More informationMAC12D, MAC12M, MAC12N
MAC12D, MAC12M, MAC12N Pb Description Designed for high performance full wave ac control applications where high noise immunity and commutating di/dt are required. Features Blocking Voltage to 800 Volts
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions DO-218 Compatible PRIMARY CHARACTERISTICS V BR 11.1 V to 52.8 V P PPM (1 x μs) 66 W P PPM (1 x
More information2N6504 Series. Thyristors. Surface Mount V > 2N6504 Series. Description
2N6504 Series Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supply crowbar circuits. Features Glass Passivated Junctions for
More informationThyristors 30 / 35 Amp Alternistor (High Commutation) Triacs
Qxx30xHx & Qxx35xHx Series RoHS Description The 30 mp / 35 mp bi-directional solid state switch series is designed for C switching and phase control applications such as motor speed and temperature modulation
More informationINSULATED GATE BIPOLAR TRANSISTOR. E n-channel
INSULATED GATE BIPOLAR TRANSISTOR PD - 9.780 UltraFast IGBT Features Switching-loss rating includes all "tail" losses Optimized for high operating frequency (over 5kHz) See Fig. for urrent vs. Frequency
More informationComchip 3KP-G Transient Voltage Suppressor Datasheet
Comchip 3KP-G Transient Suppressor Datasheet http://www.manuallib.com/comchip/3kp-g-transient-voltage-suppressor-datasheet.html Features -Glass passivated chip. -Low leakage. -Uni and Bidirection unit.
More informationKxxxzy SIDAC. Teccor brand Thyristors Standard Bidirectional SIDACs. Description
Kxxxzy SIDAC Description The SIDAC is a silicon bilateral voltage triggered switch. Upon application of a voltage exceeding the SIDAC breakover voltage point, the SIDAC switches on through a negative resistance
More informationSP4040 Series 3.3V 75A Rail Clamp Array
3.3V 7A Rail Clamp Array RoHS Pb GREEN Description The SP4040 provides overvoltage protection for applications such as 0/00/000 Base-T Ethernet and T3/ E3 interfaces. This device has a low capacitance
More informationMCR25DG, MCR25MG, MCR25NG
MCR25DG, MCR25MG, MCR25NG Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half wave, silicon gate controlled
More informationBTA30H-600CW3G, BTA30H-800CW3G
BTA30H-600CW3G, BTA30H-800CW3G Pb Description Designed for high performance full-wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage
More informationIRGBC30M Short Circuit Rated Fast IGBT
INSULTED GTE BIPOLR TRNSISTOR Features Short circuit rated - µs @ 25, V GE = 5V Switching-loss rating includes all "tail" losses Optimized for medium operating frequency ( to khz) See Fig. for urrent vs.
More informationOptocoupler, Phototransistor Output, Very High Isolation Voltage
Optocoupler, Phototransistor Output, Very High Isolation Voltage CNY64ST Top View A C FEATURES Rated recurring peak voltage (repetitive) V IORM = 145 V peak Thickness through insulation 3 mm CNY65ST Creepage
More informationR L = 60 Ω. DC Gate Trigger Voltage. = 1 kω T J = 125 C = V DRM. / V RRM Exponential Waveform R GK I G. = 10mA PW = 15μsec I T. = 3.
S602ECS RoHS Description This new.8 A sensitive gate SCR in an TO-92 package with a GAK pin out, offers a high static component series with a high static dv/dt and a low turn off (t q ) time by the use
More informationData Sheet. ASSR-1218, ASSR-1219 and ASSR-1228 Form A, Solid State Relay (Photo MOSFET) (60V/0.2A/10Ω) Features. Description. Functional Diagram
ASSR-8, ASSR-9 and ASSR-8 Form A, Solid State Relay (Photo MOSFET) (0V/0.A/0Ω) Data Sheet Description The ASSR-XX Series consists of an AlGaAs infrared light-emitting diode (LED) input stage optically
More informationSZSMF5.0AT1G Series. TVS Diodes. Surface Mount > 200W > SZSMF5.0AT1G Series. Bi-directional. Cathode. Anode. Uni-directional.
Surface Mount > 2W > SZSMF5.ATG Series SZSMF5.ATG Series Pb Description The SZSMF5.ATG Series is designed to protect voltage sensitive components from high voltage, high energy transients. Excellent clamping
More informationData Sheet. ASSR-4118, ASSR-4119 and ASSR Form A, Solid State Relay (Photo MOSFET) (400V/0.10A/35 ) Features. Description. Functional Diagram
ASSR-, ASSR-9 and ASSR- Form A, Solid State Relay (Photo MOSFET) (00V/0.0A/ ) Data Sheet Description The ASSR-XX Series consists of an AlGaAs infrared light-emitting diode (LED) input stage optically coupled
More informationFAIRCHILD TVS Is Now Part of
FAIRCHILD TVS Is Now Part of To learn more about Taiwan Semiconductor, please visit our website at www.taiwansemi.com Please note: The acquisition of this portfolio aligns with our strategy to expand in
More informationMAC228A. Thyristors. Surface Mount 400V - 800V > MAC228A. Description
MAC228A Pb Description Designed primarily for industrial and consumer applications for full wave control of AC loads such as appliance controls, heater controls, motor controls, and other power switching
More informationTeccor brand Protection Thyristors Surface Mount
Q2L Series (C-Rated) SIDACtor SLIC Device The Q2L SIDACtor SLIC series provides unidirectional transient voltage protection in a low profile, Chip Scale Package (CSP). The small package QFN (Quad Flatpak
More informationSM712 Series 600W Asymmetrical TVS Diode Array
SM712 Series 6W Asymmetrical TVS Diode Array RoHS Pb GREEN Description The SM712 TVS Diode Array is designed to protect RS-485 applications with asymmetrical working voltages (-7V to 12V from damage due
More informationBTA16-600BW3G, BTA16-800BW3G,
BTA6-600BW3G, BTA6-800BW3G, Pb Description Designed for high performance full wave ac control applications where high noise immunity and high commutating di/dt are required. Features Blocking oltage to
More informationTeccor brand Thyristors High Energy Unidirectional SIDACs
K2xx0yHU Series RoHS Description The new K2xx0yHU is a higher energy SIDC switch for gas ignition applications requiring higher current pulse current especially at low repetition rate. It is offered in
More informationSurface Mount > 600W > P6SMB11AT3G Series. Description. Features
P6SMB11AT3G Series Pb OBSOLETE/EOL DATE June/30/2018 PCN/ECN# LFPCN41246 REPLACED BY P6SMB Series Description The P6SMB11AT3G series is designed to protect voltage sensitive components from high voltage,
More informationIRGPC40S PD TO-247AC. Features V CES = 600V. V CE(sat) 1.8V. Description. Absolute Maximum Ratings. Thermal Resistance
INSULATED GATE BIPOLAR TRANSISTOR PD - 9.692 IRGP4S Standard Speed IGBT Features Switching-loss rating includes all "tail" losses Optimized for line frequency operation (to 4Hz) See Fig. for urrent vs.
More informationMAC210A8, MAC210A10. Thyristors. Surface Mount 400V - 800V > MAC210A8, MAC210A10. Description
MAC210A8, MAC210A10 Pb Description Designed primarily for full-wave AC control applications, such as light dimmers, motor controls, heating controls and power supplies; or wherever full wave silicon gate
More informationP4KE6.8A thru P4KE540A. TRANSZORB Transient Voltage Suppressors. Vishay General Semiconductor. FEATURES PRIMARY CHARACTERISTICS
TRANSZORB Transient Voltage Suppressors PRIMARY CHARACTERISTICS V WM 5.8 V to 459 V V BR uni-directional 6.8 V to 54 V V BR bi-directional 6.8 V to 44 V P PPM 4 W P D 1.5 W I FSM (uni-directional only)
More informationHigh Temperature Stability and High Reliability Conditions FEATURES
Surface Mount PAR Transient Voltage Suppressors High Temperature Stability and High Reliability Conditions Top View SlimSMA TM DO-22AC PRIMARY CHARACTERISTICS V BR 6.8 V to 5 V 5.8 V to 43.6 V P PPM (
More informationSM6T250CAY. Automotive 600 W Transil. Description. Features. Complies with the following standards
Automotive 600 W Transil Datasheet - production data Complies with the following standards IEC 61000-4-2 exceeds level 4: 30 kv (air discharge) 30 kv (contact discharge) ISO 10605, C = 330 pf, R = 330
More information2N6400. Thyristors. Surface Mount V > 2N6400. Description
2N6400 Pb Description Designed primarily for half-wave ac control applications, such as motor controls, heating controls and power supplies; or wherever half wave silicon gate controlled, solid state devices
More informationSIDACtor Protection Thyristors Broadband Optimized TM Protection. Q2L Series - 3x3 QFN. Description
Q2L Series - 3x3 QN RoHS Pb e3 Description Q2L Series 3x3 QN are low capacitance SIDACtor thyristors designed to protect high density broadband equipment from damaging overvoltage transients. The series
More information