HIGH REPEATABILITY, DC-8 GHz/20Gbps TO-5 RELAYS, DPDT

Size: px

Start display at page:

Download "HIGH REPEATABILITY, DC-8 GHz/20Gbps TO-5 RELAYS, DPDT"

Buck Patrick
5 years ago
Views:

1 HIGH REPEATABILITY, DC-8 GHz/Gbps TO-5 RELAYS, DPDT SERIES RELAY TYPE RF3 RF33 Repeatable, RF relay Low Power Operating Coil, RF relay DESCRIPTION The ultra miniature RF3 is designed to improve upon the RF3/RF33 relay s high frequency performance. The RF3/RF33 offers monotonic insertion loss to 8 GHz. This improvement in RF insertion loss over the frequency range, makes these relays highly suitable for use in attenuator and other RF circuits. The sensitive RF33 relay has a high resistance coil, thus requiring extremely low operating power ( mw typical). The RF3/RF33 features: High repeatability. Broader bandwidth. Metal enclosure for EMI shielding. Ground pin option to improve case grounding. High isolation between control and signal paths. Highly resistant to ESD. CONSTRUCTION FEATURES The following unique construction features and manufacturing techniques provide excellent resistance to environmental extremes and overall reliability. Uni-frame motor design provides high magnetic effi ciency and mechanical rigidity. Minimum mass components and welded construction provide maximum resistance to shock and vibration. Advanced cleaning techniques provide maximum assurance of internal cleanliness. Gold-plated precious metal alloy contacts ensure reliable switching and signal fi delity. Hermetically sealed. Solder-Dipped Leads, (RoHS compliant solder option available) Temperature (Ambient) Vibration (General Note I) Shock (General Note I) Enclosure Weight ENVIRONMENTAL AND PHYSICAL SPECIFICATIONS Storage Operating 65 C to +5 C 55 C to +85 C g s to 5 Hz 3 g s, 6ms half sine Hermetically sealed.9 oz. (.55g) max. 4 TELEDYNE RELAYS (8) RF3/RF33 Page

2 TYPICAL RF CHARACTERISTICS (See RF Notes) Isolation Across Contacts (RF Note 4) Isolation Pole to Pole (RF Note 5) - - Isolation (db) Normally CLosed Pole-Pole Isolation (db) De-Energized Energized -6-8 Insertion Loss (RF Note 6) VSWR (RF Note 6) Insertion Loss (db) Normally Closed VSWR Normally CLosed -5. RF3/RF33 Time Response (RF Note 6).9.7 9% 37ps reference Volt.5 6.3ps propagation delay time ps pulse rise time % Time (ps) RF NOTES. Test conditions: a. Fixture:.3" copper clad, reinforced PTFE, RT/duroid 6 with SMA connectors. (RT/duroid is a registered trademark of Rogers Corporation.) b. Room ambient temperature. c. Terminals not tested were terminated with 5-ohm load. d. Contact signal level: dbm. e. No. of test samples: 4.. Data presented herein represents typical characteristics and is not intended for use as specification limits. 3. Data is per pole, except for pole-to-pole data. 4. Data is the average from readings taken on all open contacts. 5. Data is the average from readings taken on poles with coil energized and de-energized. 6. Data is the average from readings taken on all closed contacts. 7. Test fixture effect de-embedded from frequency and time response data. RF3/RF33 Page SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 4 TELEDYNE RELAYS

3 GENERAL ELECTRICAL SPECIFICATIONS C) Contact Arrangement Rated Duty Contact Resistance Contact Load Rating Contact Life Ratings Coil Operating Power Operate Time Release Time Intercontact Capacitance Insulation Resistance Dielectric Strength Form C (DPDT) Continuous.5 Ω max. Resistive: Amp/8Vdc Low level: to 5 to 5 mv,, cycles (typical) at low level contact load RF3: 45 mw typical at nominal rated voltage RF33: mw typical at nominal rated voltage RF3: 4. ms max. RF33: 6. ms max. 3. ms max..4 pf typical, MΩ min. between mutually isolated terminals 35 Vrms (6 atmospheric pressure DETAILED ELECTRICAL SPECIFICATIONS (@5 C) BASE PART NUMBERS (RF3) RF3-5 RF3- Coil Voltage, Nominal (Vdc) 5.. Coil Resistance (Ohms ±%) 5 39 Pick-up Voltage (Vdc max.) BASE PART NUMBERS (RF33) RF33-5 RF33- Coil Voltage, Nominal (Vdc) 5.. Coil Resistance (Ohms ±%) 85 Pick-up Voltage (Vdc max.) Relay Series Teledyne Part Numbering System for RF3/RF33 RF3 X - 5 / S R Q = Solder-Coated Leads G = Gold-Plated Leads (RoHS Compliant) R = RoHS Compliant Solder Ground Pin Option (See Appendix A) S =.87 Leads No Suffi x =.75 Leads Nominal Coil Voltage General Note: Parts ordered without suffix may be supplied with Solder-Coated or Gold-Plated leads Parts ordered with Solder-Coated leads will have (Sn6/Pb4) Parts ordered with RoHS Solder-Coated leads will have (Sn99.3/Cu.7) 4 TELEDYNE RELAYS (8) RF3/RF33 Page 3

4 OUTLINE DIMENSIONS.4 MAX [.6 ] (RF33) SCHEMATIC DIAGRAM NOTES:. DIMENSIONS ARE IN INCHES, METRIC EQUIVALENTS SHOWN IN [ ].. POSTITIONS 5 AND ARE FOR UNINSULATED CASE GROUND OPTIONS. 3. NO PROTRUSION BELOW BOTTOM OF HEADER WHEN GROUND PINS ARE INSTALLED 4. TO ORDER THE CASE GROUND OPTION, AFTER THE SERIES DESIGNATOR, ADD Y TO THE PART NUMBER FOR POSITION 5 OR Z TO THE PART NUMBER FOR POSITION. GENERAL NOTES I. Relays will exhibit no contact chatter in excess of μsec or transfer in excess of μsec. II. For reference only. Coil resistance not directly measureable at relay terminals due to internal series diode. RF3/RF33 Page 4 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 4 TELEDYNE RELAYS

TYPICAL Single-Ended Signal Integrity Characteristics @ Gbps Series RF3/RF33 +5 mv V -5 mv ps ps 4 ps 6 ps 8 ps ps Bit

5 TYPICAL Single-Ended Signal Integrity Gbps Series RF3/RF33 +5 mv V -5 mv ps ps 4 ps 6 ps 8 ps ps Bit Rate Eye Height Eye Width Jitter P-P Gbps 9 mv 37 ps. ps 4 TELEDYNE RELAYS (8) RF3/RF33 Page 5

HIGH REPEATABILITY, TO-5 RELAYS DPDT

HIGH REPEATABILITY, TO-5 RELAYS DPDT SERIES RELAY TYPE RF7 RF7 Repeatable, RF relay Sensitive, repeatable, RF relay DESCRIPTION The ultraminiature RF7 and RF7 relays are designed to provide improved RF