Boise State University Department of Electrical and Computer Engineering ECE 212L Circuit Analysis and Design Lab

Size: px
Start display at page:

Download "Boise State University Department of Electrical and Computer Engineering ECE 212L Circuit Analysis and Design Lab"

Transcription

1 Objectives Boise State University Department of Electrical and Computer Engineering ECE L Circuit Analysis and Design Lab Experiment #0: Frequency esponse Measurements The objectives of this laboratory experiment are: To obtain the frequency response (magnitude and phase) of a two-port network. To identify the transfer function of a minimum-phase network from the poles and zeros of the corresponding Bode magnitude plot. Theory X(s) H(s) Y(s) ~ X H(j ω) ~ Y (a) (b) Figure : (a) Transfer Function and (b) its Frequency esponse Consider the block diagram representation of a transfer function in Figure (a). ecall that the transfer function of a linear circuit is defined as the ratio of the output response Y (s) to an input signal X(s) with all initially conditions set equal to zero, i.e., with all initial inductor currents and all initial capacitor voltages set equal to zero. Mathematically, H(s) = Y (s) X(s) The input X(s) can be a voltage source or a current source. The output Y (s) is usually a voltage or a current output. The transfer function H(s) has different names depending on the choice of input and output variables as shown in Table. Table : Descriptive Names of Transfer Functions Input X(s) Output Y (s) Transfer Function H(s) = Y (s)/x(s) Voltage Source Voltage Output Voltage Gain Voltage Source Current Output Admittance Current Source Voltage Output Impedance Current Source Current Output Current Gain Usually, the transfer function of a linear circuit is derived as a rational fraction of two polynomials in the Laplace variable s. The numerator and denominator of H(s) can be factored out to yield the zeros (roots of the numerator of H(s)) and poles (roots of the denominator of H(s)) as follows: H(s) = N(s) D(s) = K(s z ) (s z m ) (s p ) (s p n ) () ()

2 Under the form of Equation (), the transfer function H(s) has m zeros equal to z,..., z m and n poles equal to p,..., p n. If a sinusoidal signal x(t) = X m cos(ωt θ i ) is applied to the input of a linear circuit, then its output response y(t) = Y m cos(ωt θ o ) will be sinusoidal after all the circuit transients have died out. As the frequency is varied from zero to infinity, the ratio of the output phasor Ȳ = Y m θ o to the input phasor X = X m θ i is called the frequency response of the linear circuit H(jω) = H(ω) θ(ω) = Ȳ X = Y m θ o X m θ i = Y m X m (θ o θ i ) (3) The magnitude H(ω) of the frequency response can be obtained from the ratio of the peak-to-peak output voltage to the peak-to-peak input voltage as follows: H(ω) = Y m X m = Y m X m = Y pp X pp (4) The phase θ(ω) of the frequency response can be measured from the time delay of the output sinusoid with respect to the input sinusoid as follows: θ(ω) = θ o θ i = 360 o t T The relationship between a transfer function and its frequency response is shown in Figure (b). It can be shown that the transfer function H(jω) = H(ω) θ(ω) can be obtained from the transfer function H(s) by replacing the Laplace variable s by jω, that is, H(jω) = H(ω) θ(ω) = [H(s)] s = jω (6) and converting the resulting complex expression into polar form (magnitude and angle). The frequency response can be visualized with the plots of the magnitude and phase of H(jω) as a function of frequency ω (rad/s) or f (Hz). If the frequency response of a circuit is known, it will allow the prediction of the output response to any periodic input, whether sinusoidal or nonsinusoidal. For example, a periodic input signal such a square or triangular waveform can be decomposed as a sum of sinusoids called its Fourier series representation. The output response of each sinusoidal component can be found from the definition of the frequency response at a particular frequency ω as Ỹ = Y m θ o = H(jω ) X = H(ω )X m (θ i θ(ω )) (7) yielding the output sinusoidal waveform y(t) = Y m cos(ω t θ o ) = H(ω )X m cos(ω t θ i θ(ω )) (8) Equations (7) or (8) indicate how the particular sinusoidal component at the frequency ω = ω will be effected by the frequency response of the circuit. It is clear that the magnitude Y m of the output response will be equal to the magnitude X m of the input signal multiplied by the gain H(ω ) of the frequency response at ω = ω and the phase θ o of the output response will be shifted from the phase θ i of the input signal by the phase θ(ω ) of the frequency response at ω = ω. Another representation of the frequency response of a circuit is in terms of the Bode magnitude and phase plots. The Bode magnitude in decibels (db) is defined by H (db) = 0 log 0 H(ω) (9) (5)

3 where log 0 is the logarithm of base 0. This magnitude in db is plotted as a function of the logarithm of base 0 of the frequency ω (rad/s) or frequency f (Hz) on semilog paper. The phase θ(ω) of the frequency response is also plotted as a function of the logarithm of base 0 of the frequency ω (rad/s) or frequency f (Hz) on semilog paper. A knowledge of the simple poles and zeros of the transfer function H(s) allows a quick manual sketch of these plots which are referred to as the Bode straightline approximations. sc sc V (s) i V o (s) (a) H (db) db/dec 0 db/dec 0.f f f 0f f (Hz) (b) 90 θ (deg) deg/dec 0.f f 90 deg/dec f 0f f (Hz) 45 deg/dec 90 (c) Figure : (a) Bandpass Filter and (b) its Bode Magnitude and (c) Bode Phase Plots In this experiment, the transfer function of the op-amp circuit shown in Figure (a) will be identified from frequency response measurements. The circuit in Figure (a) is a bandpass filter. The transfer 3

4 function of this circuit can be shown to equal H(s) = V o(s) V i (s) = sc ( sc )( sc ) = Ks ( s/ω )( s/ω ) where K = C, ω = /C, and ω = /C. The magnitude and phase of the frequency response H(jω) are found as K(jω) H(jω) = H(ω) θ(ω) = ( jω/ω )( jω/ω ) Kω = (ω/ω ) ( (ω/ω ) 90 o tan ω tan ω () ω ω The straightline Bode magnitude plot is shown in a solid line in Figure (b). The low-frequency asymptote starts with a slope of 0 db/dec due to the pure differentiator in the numerator. The gain then flattens after encountering the first pole at ω and then drops with a slope of -0 db/dec after encountering the second pole at ω. The low-frequency asymptote crosses the midband gain at the corner frequency f while the high-frequency asymptote crosses the midband gain at f. The exact Bode magnitude plot is shown in a dashed line and has a maximum error of -3 db at the corner frequencies f and f. In other words, the actual amplifier gain has a maximum error of about 3 db at these corner frequencies which are also known at the 3-dB frequencies. The gain in actual units (V/V) is / or of the midband gain at these corner frequencies. The straightline Bode phase plot is shown in a solid line in Figure (c). The phase plot starts flat at 90 o degrees one decade below the corner frequency f and then drops off at a rate of -45 deg/dec for one decade. Between the frequencies f and f = 0f, the slope is -90 deg/dec. Finally, the straight-line slope is -45 Deg/dec before leveling off at 90 o. The exact Bode phase plot is shown in a dashed line and has a maximum error of about 6 degrees at f /0 and at 0f. 3 Equipment Agilent DSO504A Digital Storage Oscilloscope Agilent 330A Function/Arbitrary Waveform Generator Fluke 5 True MS Multimeter Assorted resistors, capacitors, and op-amps 4 Procedure. Measure the following components using your benchtop multimeter. Table : Parameter Measurements (0) C C Nominal 00n 6k n 60k Measured. Wire the op-amp circuit in Figure (a) on your protoboard. Set your function generator on HIGH Z and apply a -V peak-to-peak sine waveform with variable frequency and no offset to the input of the C network. Set up the infinium scope to record the following quantities: 4

5 Table : Frequency esponse Measurements f (Hz) V i,pp (V) V o,pp (V) t (µs) θ = 360 o t/t (deg) k k 4k 6k 8k 0k 5 Data Analysis and Interpretation. Derive the transfer function shown in Eq. (0).. Plot the exact Bode magnitude and phase plots for the op-amp filter of Figure (a) on two separate graphs. Compare the shape of these graphs with those shown in dashed lines in Figures (b) and (c). 3. On the magnitude plot, manually draw the midband gain and read off its value from the exact plot. 4. Draw the low-frequency and high-frequency asymptotes on the Bode magnitude plot. Verify that they intersect the midband gain at the 3-dB corner frequencies f (Hz) and f (Hz) which are 3 db below the midband gain on the exact magnitude plot. 5. From the knowledge of f (Hz) and f (Hz), add manually the Bode straight-line phase approximations. ead off the exact values of the phase at the corner frequencies f (Hz) and f (Hz). 6. Using the measured values for and, deduce the unknown capacitor values C (µf) and C (nf) from the corner frequencies f (Hz) and f (Hz). 5

6 Boise State University Department of Electrical and Computer Engineering ECE L Circuit Analysis and Design Lab Experiment #0: Frequency esponse Measurements Date: Data Sheet ecorded by: Equipment Agilent DSO504A Digital Storage Oscilloscope Agilent 330A Function/Arbitrary Waveform Generator Fluke 5 True MS Multimeter BSU Tag Number or Serial Number Table : Parameter Measurements C C Nominal 00n 6k n 60k Measured Table : Frequency esponse Measurements f (Hz) V i,pp (V) V o,pp (V) t = t t (µs) θ = θ θ (deg) k k 4k 6k 8k 0k

Boise State University Department of Electrical and Computer Engineering ECE 212L Circuit Analysis and Design Lab

Boise State University Department of Electrical and Computer Engineering ECE 212L Circuit Analysis and Design Lab Objecties Boise State Uniersity Department of Electrical and Computer Engineering ECE 22L Circuit Analysis and Design Lab Experiment #2: Sinusoidal Steady State and Resonant Circuits The objecties of this

More information

ECE 3155 Experiment I AC Circuits and Bode Plots Rev. lpt jan 2013

ECE 3155 Experiment I AC Circuits and Bode Plots Rev. lpt jan 2013 Signature Name (print, please) Lab section # Lab partner s name (if any) Date(s) lab was performed ECE 3155 Experiment I AC Circuits and Bode Plots Rev. lpt jan 2013 In this lab we will demonstrate basic

More information

FREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY

FREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY FREQUENCY RESPONSE AND PASSIVE FILTERS LABORATORY In this experiment we will analytically determine and measure the frequency response of networks containing resistors, AC source/sources, and energy storage

More information

, answer the next six questions.

, answer the next six questions. Frequency Response Problems Conceptual Questions 1) T/F Given f(t) = A cos (ωt + θ): The amplitude of the output in sinusoidal steady-state increases as K increases and decreases as ω increases. 2) T/F

More information

Pole, zero and Bode plot

Pole, zero and Bode plot Pole, zero and Bode plot EC04 305 Lecture notes YESAREKEY December 12, 2007 Authored by: Ramesh.K Pole, zero and Bode plot EC04 305 Lecture notes A rational transfer function H (S) can be expressed as

More information

EECS40 RLC Lab guide

EECS40 RLC Lab guide EECS40 RLC Lab guide Introduction Second-Order Circuits Second order circuits have both inductor and capacitor components, which produce one or more resonant frequencies, ω0. In general, a differential

More information

RLC Frequency Response

RLC Frequency Response 1. Introduction RLC Frequency Response The student will analyze the frequency response of an RLC circuit excited by a sinusoid. Amplitude and phase shift of circuit components will be analyzed at different

More information

Integrators, differentiators, and simple filters

Integrators, differentiators, and simple filters BEE 233 Laboratory-4 Integrators, differentiators, and simple filters 1. Objectives Analyze and measure characteristics of circuits built with opamps. Design and test circuits with opamps. Plot gain vs.

More information

Electric Circuit Theory

Electric Circuit Theory Electric Circuit Theory Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Chapter 15 Active Filter Circuits Nam Ki Min nkmin@korea.ac.kr 010-9419-2320 Contents and Objectives 3 Chapter Contents 15.1 First-Order

More information

ENG 100 Lab #2 Passive First-Order Filter Circuits

ENG 100 Lab #2 Passive First-Order Filter Circuits ENG 100 Lab #2 Passive First-Order Filter Circuits In Lab #2, you will construct simple 1 st -order RL and RC filter circuits and investigate their frequency responses (amplitude and phase responses).

More information

EK307 Active Filters and Steady State Frequency Response

EK307 Active Filters and Steady State Frequency Response EK307 Active Filters and Steady State Frequency Response Laboratory Goal: To explore the properties of active signal-processing filters Learning Objectives: Active Filters, Op-Amp Filters, Bode plots Suggested

More information

EK307 Passive Filters and Steady State Frequency Response

EK307 Passive Filters and Steady State Frequency Response EK307 Passive Filters and Steady State Frequency Response Laboratory Goal: To explore the properties of passive signal-processing filters Learning Objectives: Passive filters, Frequency domain, Bode plots

More information

Lecture 16 Date: Frequency Response (Contd.)

Lecture 16 Date: Frequency Response (Contd.) Lecture 16 Date: 03.10.2017 Frequency Response (Contd.) Bode Plot (contd.) Bode Plot (contd.) Bode Plot (contd.) not every transfer function has all seven factors. To sketch the Bode plots for a generic

More information

Lab 6: Building a Function Generator

Lab 6: Building a Function Generator ECE 212 Spring 2010 Circuit Analysis II Names: Lab 6: Building a Function Generator Objectives In this lab exercise you will build a function generator capable of generating square, triangle, and sine

More information

BME 3512 Bioelectronics Laboratory Two - Passive Filters

BME 3512 Bioelectronics Laboratory Two - Passive Filters BME 35 Bioelectronics Laboratory Two - Passive Filters Learning Objectives: Understand the basic principles of passive filters. Laboratory Equipment: Agilent Oscilloscope Model 546A Agilent Function Generator

More information

Kent Bertilsson Muhammad Amir Yousaf

Kent Bertilsson Muhammad Amir Yousaf Today s topics Analog System (Rev) Frequency Domain Signals in Frequency domain Frequency analysis of signals and systems Transfer Function Basic elements: R, C, L Filters RC Filters jw method (Complex

More information

Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4

Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4 EECS 16B Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4 This homework is solely for your own practice. However, everything on it is in scope for midterm 1,

More information

Introduction to Signals, Passive RC Filters and Opamps

Introduction to Signals, Passive RC Filters and Opamps Introduction to Signals, ive RC Filters and Opamps LB Introduction In this laboratory exercise you design, build and test some simple filter circuits. his is mainly for you to get comfortable with circuit

More information

Filter Design, Active Filters & Review. EGR 220, Chapter 14.7, December 14, 2017

Filter Design, Active Filters & Review. EGR 220, Chapter 14.7, December 14, 2017 Filter Design, Active Filters & Review EGR 220, Chapter 14.7, 14.11 December 14, 2017 Overview ² Passive filters (no op amps) ² Design examples ² Active filters (use op amps) ² Course review 2 Example:

More information

EECS 216 Winter 2008 Lab 2: FM Detector Part I: Intro & Pre-lab Assignment

EECS 216 Winter 2008 Lab 2: FM Detector Part I: Intro & Pre-lab Assignment EECS 216 Winter 2008 Lab 2: Part I: Intro & Pre-lab Assignment c Kim Winick 2008 1 Introduction In the first few weeks of EECS 216, you learned how to determine the response of an LTI system by convolving

More information

SECTION 7: FREQUENCY DOMAIN ANALYSIS. MAE 3401 Modeling and Simulation

SECTION 7: FREQUENCY DOMAIN ANALYSIS. MAE 3401 Modeling and Simulation SECTION 7: FREQUENCY DOMAIN ANALYSIS MAE 3401 Modeling and Simulation 2 Response to Sinusoidal Inputs Frequency Domain Analysis Introduction 3 We ve looked at system impulse and step responses Also interested

More information

STATION NUMBER: LAB SECTION: Filters. LAB 6: Filters ELECTRICAL ENGINEERING 43/100 INTRODUCTION TO MICROELECTRONIC CIRCUITS

STATION NUMBER: LAB SECTION: Filters. LAB 6: Filters ELECTRICAL ENGINEERING 43/100 INTRODUCTION TO MICROELECTRONIC CIRCUITS Lab 6: Filters YOUR EE43/100 NAME: Spring 2013 YOUR PARTNER S NAME: YOUR SID: YOUR PARTNER S SID: STATION NUMBER: LAB SECTION: Filters LAB 6: Filters Pre- Lab GSI Sign- Off: Pre- Lab: /40 Lab: /60 Total:

More information

ωc ωc sin(wt 90o ) (for a capacitance) (4)

ωc ωc sin(wt 90o ) (for a capacitance) (4) Physics'241'Signal'Processing:'Lab'3' Sinusoidal esponse of, L ircuits In the previous lab, we studied the behavior of series combinations of and L circuits with input square and triangular waveforms.

More information

ME 365 EXPERIMENT 7 SIGNAL CONDITIONING AND LOADING

ME 365 EXPERIMENT 7 SIGNAL CONDITIONING AND LOADING ME 365 EXPERIMENT 7 SIGNAL CONDITIONING AND LOADING Objectives: To familiarize the student with the concepts of signal conditioning. At the end of the lab, the student should be able to: Understand the

More information

Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4

Designing Information Devices and Systems II Fall 2018 Elad Alon and Miki Lustig Homework 4 EECS 6B Designing Information Devices and Systems II Fall 208 Elad Alon and Miki Lustig Homework 4 This homework is solely for your own practice. However, everything on it is in scope for midterm, and

More information

EE-2302 Passive Filters and Frequency Response

EE-2302 Passive Filters and Frequency Response EE2302 Passive Filters and Frequency esponse Objective he student should become acquainted with simple passive filters for performing highpass, lowpass, and bandpass operations. he experimental tasks also

More information

ECE 231 Laboratory Exercise 6 Frequency / Time Response of RL and RC Circuits

ECE 231 Laboratory Exercise 6 Frequency / Time Response of RL and RC Circuits ECE 231 Laboratory Exercise 6 Frequency / Time Response of RL and RC Circuits Laboratory Group (Names) OBJECTIVES Observe and calculate the response of first-order low pass and high pass filters. Gain

More information

H represents the value of the transfer function (frequency response) at

H represents the value of the transfer function (frequency response) at Measurements in Electronics and Telecommunication - Laboratory 4 1 Laboratory 4 Measurements of frequency response Purpose: Measuring the cut-off frequency of a filter. The representation of frequency

More information

ECE 4670 Spring 2014 Lab 1 Linear System Characteristics

ECE 4670 Spring 2014 Lab 1 Linear System Characteristics ECE 4670 Spring 2014 Lab 1 Linear System Characteristics 1 Linear System Characteristics The first part of this experiment will serve as an introduction to the use of the spectrum analyzer in making absolute

More information

EE 233 Circuit Theory Lab 3: First-Order Filters

EE 233 Circuit Theory Lab 3: First-Order Filters EE 233 Circuit Theory Lab 3: First-Order Filters Table of Contents 1 Introduction... 1 2 Precautions... 1 3 Prelab Exercises... 2 3.1 Inverting Amplifier... 3 3.2 Non-Inverting Amplifier... 4 3.3 Integrating

More information

Operational Amplifier BME 360 Lecture Notes Ying Sun

Operational Amplifier BME 360 Lecture Notes Ying Sun Operational Amplifier BME 360 Lecture Notes Ying Sun Characteristics of Op-Amp An operational amplifier (op-amp) is an analog integrated circuit that consists of several stages of transistor amplification

More information

Experiment 8 Frequency Response

Experiment 8 Frequency Response Experiment 8 Frequency Response W.T. Yeung, R.A. Cortina, and R.T. Howe UC Berkeley EE 105 Spring 2005 1.0 Objective This lab will introduce the student to frequency response of circuits. The student will

More information

PYKC 13 Feb 2017 EA2.3 Electronics 2 Lecture 8-1

PYKC 13 Feb 2017 EA2.3 Electronics 2 Lecture 8-1 In this lecture, I will cover amplitude and phase responses of a system in some details. What I will attempt to do is to explain how would one be able to obtain the frequency response from the transfer

More information

Electronics basics for MEMS and Microsensors course

Electronics basics for MEMS and Microsensors course Electronics basics for course, a.a. 2017/2018, M.Sc. in Electronics Engineering Transfer function 2 X(s) T(s) Y(s) T S = Y s X(s) The transfer function of a linear time-invariant (LTI) system is the function

More information

E C E M I C R O E L E C T R O N I C S I L E C T U R E N O T E S. Spring 2018

E C E M I C R O E L E C T R O N I C S I L E C T U R E N O T E S. Spring 2018 E C E 3 4 1 0 M I C R O E L E C T R O N I C S I L E C T U R E N O T E S Spring 2018 Chris Winstead Associate Professor Electrical and Computer Engineering chris.winstead@usu.edu Copyright 2018 published

More information

University of Illinois at Chicago Spring ECE 412 Introduction to Filter Synthesis Homework #2 Solutions. Problem 1

University of Illinois at Chicago Spring ECE 412 Introduction to Filter Synthesis Homework #2 Solutions. Problem 1 Problem 1 (a) Magnitude (impedance) scale the circuit so that all resistors are 1kΩ. Solution: Since all of the resistors in the circuit are 1Ω, we need to magnitude scale by k m = 1000; therefore, we

More information

POLYTECHNIC UNIVERSITY Electrical Engineering Department. EE SOPHOMORE LABORATORY Experiment 5 RC Circuits Frequency Response

POLYTECHNIC UNIVERSITY Electrical Engineering Department. EE SOPHOMORE LABORATORY Experiment 5 RC Circuits Frequency Response POLYTECHNIC UNIVERSITY Electrical Engineering Department EE SOPHOMORE LORTORY Eperiment 5 RC Circuits Frequency Response Modified for Physics 18, rooklyn College I. Overview of Eperiment In this eperiment

More information

AC BEHAVIOR OF COMPONENTS

AC BEHAVIOR OF COMPONENTS AC BEHAVIOR OF COMPONENTS AC Behavior of Capacitor Consider a capacitor driven by a sine wave voltage: I(t) 2 1 U(t) ~ C 0-1 -2 0 2 4 6 The current: is shifted by 90 o (sin cos)! 1.0 0.5 0.0-0.5-1.0 0

More information

Operational Amplifiers: Part II

Operational Amplifiers: Part II 1. Introduction Operational Amplifiers: Part II The name "operational amplifier" comes from this amplifier's ability to perform mathematical operations. Three good examples of this are the summing amplifier,

More information

Homework Assignment 06

Homework Assignment 06 Question 1 (2 points each unless noted otherwise) Homework Assignment 06 1. True or false: when transforming a circuit s diagram to a diagram of its small-signal model, we replace dc constant current sources

More information

CHAPTER 6 Frequency Response, Bode. Plots, and Resonance

CHAPTER 6 Frequency Response, Bode. Plots, and Resonance CHAPTER 6 Frequency Response, Bode Plots, and Resonance CHAPTER 6 Frequency Response, Bode Plots, and Resonance 1. State the fundamental concepts of Fourier analysis. 2. Determine the output of a filter

More information

ECE 203 LAB 2 PRACTICAL FILTER DESIGN & IMPLEMENTATION

ECE 203 LAB 2 PRACTICAL FILTER DESIGN & IMPLEMENTATION Version 1. 1 of 7 ECE 03 LAB PRACTICAL FILTER DESIGN & IMPLEMENTATION BEFORE YOU BEGIN PREREQUISITE LABS ECE 01 Labs ECE 0 Advanced MATLAB ECE 03 MATLAB Signals & Systems EXPECTED KNOWLEDGE Understanding

More information

Homework Assignment 03

Homework Assignment 03 Homework Assignment 03 Question 1 (Short Takes), 2 points each unless otherwise noted. 1. Two 0.68 μf capacitors are connected in series across a 10 khz sine wave signal source. The total capacitive reactance

More information

ET 304A Laboratory Tutorial-Circuitmaker For Transient and Frequency Analysis

ET 304A Laboratory Tutorial-Circuitmaker For Transient and Frequency Analysis ET 304A Laboratory Tutorial-Circuitmaker For Transient and Frequency Analysis All circuit simulation packages that use the Pspice engine allow users to do complex analysis that were once impossible to

More information

EE233 Autumn 2016 Electrical Engineering University of Washington. EE233 HW7 Solution. Nov. 16 th. Due Date: Nov. 23 rd

EE233 Autumn 2016 Electrical Engineering University of Washington. EE233 HW7 Solution. Nov. 16 th. Due Date: Nov. 23 rd EE233 HW7 Solution Nov. 16 th Due Date: Nov. 23 rd 1. Use a 500nF capacitor to design a low pass passive filter with a cutoff frequency of 50 krad/s. (a) Specify the cutoff frequency in hertz. fc c 50000

More information

ECE3204 D2015 Lab 1. See suggested breadboard configuration on following page!

ECE3204 D2015 Lab 1. See suggested breadboard configuration on following page! ECE3204 D2015 Lab 1 The Operational Amplifier: Inverting and Non-inverting Gain Configurations Gain-Bandwidth Product Relationship Frequency Response Limitation Transfer Function Measurement DC Errors

More information

CHAPTER 6 INTRODUCTION TO SYSTEM IDENTIFICATION

CHAPTER 6 INTRODUCTION TO SYSTEM IDENTIFICATION CHAPTER 6 INTRODUCTION TO SYSTEM IDENTIFICATION Broadly speaking, system identification is the art and science of using measurements obtained from a system to characterize the system. The characterization

More information

Experiment Guide: RC/RLC Filters and LabVIEW

Experiment Guide: RC/RLC Filters and LabVIEW Description and ackground Experiment Guide: RC/RLC Filters and LabIEW In this lab you will (a) manipulate instruments manually to determine the input-output characteristics of an RC filter, and then (b)

More information

I. Introduction to Simple Circuits of Resistors

I. Introduction to Simple Circuits of Resistors 2 Problem Set for Dr. Todd Huffman Michaelmas Term I. Introduction to Simple ircuits of esistors 1. For the following circuit calculate the currents through and voltage drops across all resistors. The

More information

ECE 2006 University of Minnesota Duluth Lab 11. AC Circuits

ECE 2006 University of Minnesota Duluth Lab 11. AC Circuits 1. Objective AC Circuits In this lab, the student will study sinusoidal voltages and currents in order to understand frequency, period, effective value, instantaneous power and average power. Also, the

More information

EE 230 Lab Lab nf C 2. A. Low-Q low-pass active filters. (a) 10 k! Figure 1. (a) First-order low-pass. (b) Second-order low-pass.

EE 230 Lab Lab nf C 2. A. Low-Q low-pass active filters. (a) 10 k! Figure 1. (a) First-order low-pass. (b) Second-order low-pass. Second-order filter circuits This time, we measure frequency response plots for second-order filters. We start by examining a simple 2nd-order low-pass filter. The we look at the various arrangements of

More information

Laboratory Manual. ELEN-325 Electronics

Laboratory Manual. ELEN-325 Electronics Laboratory Manual ELEN-325 Electronics Department of Electrical & Computer Engineering Texas A&M University Prepared by: Dr. Jose Silva-Martinez (jsilva@ece.tamu.edu) Rida Assaad (rida@ece.tamu.edu) Raghavendra

More information

ECE4902 C Lab 5 MOSFET Common Source Amplifier with Active Load Bandwidth of MOSFET Common Source Amplifier: Resistive Load / Active Load

ECE4902 C Lab 5 MOSFET Common Source Amplifier with Active Load Bandwidth of MOSFET Common Source Amplifier: Resistive Load / Active Load ECE4902 C2012 - Lab 5 MOSFET Common Source Amplifier with Active Load Bandwidth of MOSFET Common Source Amplifier: Resistive Load / Active Load PURPOSE: The primary purpose of this lab is to measure the

More information

332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title: Function Generators and Oscilloscopes Suggested Equipment:

332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title: Function Generators and Oscilloscopes Suggested Equipment: RUTGERS UNIVERSITY The State University of New Jersey School of Engineering Department Of Electrical and Computer Engineering 332:223 Principles of Electrical Engineering I Laboratory Experiment #2 Title:

More information

ECEN 325 Lab 5: Operational Amplifiers Part III

ECEN 325 Lab 5: Operational Amplifiers Part III ECEN Lab : Operational Amplifiers Part III Objectives The purpose of the lab is to study some of the opamp configurations commonly found in practical applications and also investigate the non-idealities

More information

v(t) = V p sin(2π ft +φ) = V p cos(2π ft +φ + π 2 )

v(t) = V p sin(2π ft +φ) = V p cos(2π ft +φ + π 2 ) 1 Let us revisit sine and cosine waves. A sine wave can be completely defined with three parameters Vp, the peak voltage (or amplitude), its frequency w in radians/second or f in cycles/second (Hz), and

More information

BME 3512 Bioelectronics Laboratory Five - Operational Amplifiers

BME 3512 Bioelectronics Laboratory Five - Operational Amplifiers BME 351 Bioelectronics Laboratory Five - Operational Amplifiers Learning Objectives: Be familiar with the operation of a basic op-amp circuit. Be familiar with the characteristics of both ideal and real

More information

Experiment 9 AC Circuits

Experiment 9 AC Circuits Experiment 9 AC Circuits "Look for knowledge not in books but in things themselves." W. Gilbert (1540-1603) OBJECTIVES To study some circuit elements and a simple AC circuit. THEORY All useful circuits

More information

The above figure represents a two stage circuit. Recall, the transfer function relates. Vout

The above figure represents a two stage circuit. Recall, the transfer function relates. Vout LABORATORY 12: Bode plots/second Order Filters Material covered: Multistage circuits Bode plots Design problem Overview Notes: Two stage circuits: Vin1 H1(s) Vout1 Vin2 H2(s) Vout2 The above figure represents

More information

Lab #2: Electrical Measurements II AC Circuits and Capacitors, Inductors, Oscillators and Filters

Lab #2: Electrical Measurements II AC Circuits and Capacitors, Inductors, Oscillators and Filters Lab #2: Electrical Measurements II AC Circuits and Capacitors, Inductors, Oscillators and Filters Goal: In circuits with a time-varying voltage, the relationship between current and voltage is more complicated

More information

EE 241 Experiment #7: NETWORK THEOREMS, LINEARITY, AND THE RESPONSE OF 1 ST ORDER RC CIRCUITS 1

EE 241 Experiment #7: NETWORK THEOREMS, LINEARITY, AND THE RESPONSE OF 1 ST ORDER RC CIRCUITS 1 EE 241 Experiment #7: NETWORK THEOREMS, LINEARITY, AND THE RESPONSE OF 1 ST ORDER RC CIRCUITS 1 PURPOSE: To verify the validity of Thevenin and maximum power transfer theorems. To demonstrate the linear

More information

LAB 4: OPERATIONAL AMPLIFIER CIRCUITS

LAB 4: OPERATIONAL AMPLIFIER CIRCUITS LAB 4: OPERATIONAL AMPLIFIER CIRCUITS ELEC 225 Introduction Operational amplifiers (OAs) are highly stable, high gain, difference amplifiers that can handle signals from zero frequency (dc signals) up

More information

Bode plot, named after Hendrik Wade Bode, is usually a combination of a Bode magnitude plot and Bode phase plot:

Bode plot, named after Hendrik Wade Bode, is usually a combination of a Bode magnitude plot and Bode phase plot: Bode plot From Wikipedia, the free encyclopedia A The Bode plot for a first-order (one-pole) lowpass filter Bode plot, named after Hendrik Wade Bode, is usually a combination of a Bode magnitude plot and

More information

BME 3512 Bioelectronics Laboratory Six - Active Filters

BME 3512 Bioelectronics Laboratory Six - Active Filters BME 5 Bioelectronics Laboratory Six - Active Filters Learning Objectives: Understand the basic principles of active filters. Describe the differences between active and passive filters. Laboratory Equipment:

More information

Study of Inductive and Capacitive Reactance and RLC Resonance

Study of Inductive and Capacitive Reactance and RLC Resonance Objective Study of Inductive and Capacitive Reactance and RLC Resonance To understand how the reactance of inductors and capacitors change with frequency, and how the two can cancel each other to leave

More information

Poles and Zeros of H(s), Analog Computers and Active Filters

Poles and Zeros of H(s), Analog Computers and Active Filters Poles and Zeros of H(s), Analog Computers and Active Filters Physics116A, Draft10/28/09 D. Pellett LRC Filter Poles and Zeros Pole structure same for all three functions (two poles) HR has two poles and

More information

Välkomna till TSRT15 Reglerteknik Föreläsning 5. Summary of lecture 4 Frequency response Bode plot

Välkomna till TSRT15 Reglerteknik Föreläsning 5. Summary of lecture 4 Frequency response Bode plot Välkomna till TSRT15 Reglerteknik Föreläsning 5 Summary of lecture 4 Frequency response Bode plot Summary of last lecture 2 Given a pole polynomial with a varying parameter P(s)+KQ(s)=0 We draw the location

More information

ECE 2201 PRELAB 6 BJT COMMON EMITTER (CE) AMPLIFIER

ECE 2201 PRELAB 6 BJT COMMON EMITTER (CE) AMPLIFIER ECE 2201 PRELAB 6 BJT COMMON EMITTER (CE) AMPLIFIER Hand Analysis P1. Determine the DC bias for the BJT Common Emitter Amplifier circuit of Figure 61 (in this lab) including the voltages V B, V C and V

More information

EE Experiment 8 Bode Plots of Frequency Response

EE Experiment 8 Bode Plots of Frequency Response EE16:Exp8-1 EE 16 - Experiment 8 Bode Plots of Frequency Response Objectives: To illustrate the relationship between a system frequency response and the frequency response break frequencies, factor powers,

More information

Experiment #10: Passive Filter Design

Experiment #10: Passive Filter Design SCHOOL OF ENGINEEING AND APPLIED SCIENCE DEPATMENT OF ELECTICAL AND COMPUTE ENGINEEING ECE 2110: CICUIT THEOY LABOATOY Experiment #10: Passive Filter Design EQUIPMENT Lab Equipment Equipment Description

More information

PHYSICS 330 LAB Operational Amplifier Frequency Response

PHYSICS 330 LAB Operational Amplifier Frequency Response PHYSICS 330 LAB Operational Amplifier Frequency Response Objectives: To measure and plot the frequency response of an operational amplifier circuit. History: Operational amplifiers are among the most widely

More information

EE 368 Electronics Lab. Experiment 10 Operational Amplifier Applications (2)

EE 368 Electronics Lab. Experiment 10 Operational Amplifier Applications (2) EE 368 Electronics Lab Experiment 10 Operational Amplifier Applications (2) 1 Experiment 10 Operational Amplifier Applications (2) Objectives To gain experience with Operational Amplifier (Op-Amp). To

More information

PURPOSE: NOTE: Be sure to record ALL results in your laboratory notebook.

PURPOSE: NOTE: Be sure to record ALL results in your laboratory notebook. EE4902 Lab 9 CMOS OP-AMP PURPOSE: The purpose of this lab is to measure the closed-loop performance of an op-amp designed from individual MOSFETs. This op-amp, shown in Fig. 9-1, combines all of the major

More information

Experiment No. 6. Audio Tone Control Amplifier

Experiment No. 6. Audio Tone Control Amplifier Experiment No. 6. Audio Tone Control Amplifier By: Prof. Gabriel M. Rebeiz The University of Michigan EECS Dept. Ann Arbor, Michigan Goal: The goal of Experiment #6 is to build and test a tone control

More information

Homework Assignment 11

Homework Assignment 11 Homework Assignment 11 Question 1 (Short Takes) Two points each unless otherwise indicated. 1. What is the 3-dB bandwidth of the amplifier shown below if r π = 2.5K, r o = 100K, g m = 40 ms, and C L =

More information

Series and Parallel Resonance

Series and Parallel Resonance School of Engineering Department of Electrical and Computer Engineering 33:4 Principles of Electrical Engineering II aboratory Experiment 1 Series and Parallel esonance 1 Introduction Objectives To introduce

More information

Laboratory 8 Lock-in amplifier 1

Laboratory 8 Lock-in amplifier 1 Laboratory 8 Lock-in amplifier 1 Prior to the lab, Understand the circuit (Figure 1). Download from the blog and read the spec sheets for the comparator and the quadrant multiplier. Draw how to connect

More information

DEPARTMENT OF ELECTRICAL ENGINEERING AND COMPUTER SCIENCE MASSACHUSETTS INSTITUTE OF TECHNOLOGY CAMBRIDGE, MASSACHUSETTS 02139

DEPARTMENT OF ELECTRICAL ENGINEERING AND COMPUTER SCIENCE MASSACHUSETTS INSTITUTE OF TECHNOLOGY CAMBRIDGE, MASSACHUSETTS 02139 DEPARTMENT OF ELECTRICAL ENGINEERING AND COMPUTER SCIENCE MASSACHUSETTS INSTITUTE OF TECHNOLOGY CAMBRIDGE, MASSACHUSETTS 019.101 Introductory Analog Electronics Laboratory Laboratory No. READING ASSIGNMENT

More information

ELEG 205 Analog Circuits Laboratory Manual Fall 2016

ELEG 205 Analog Circuits Laboratory Manual Fall 2016 ELEG 205 Analog Circuits Laboratory Manual Fall 2016 University of Delaware Dr. Mark Mirotznik Kaleb Burd Patrick Nicholson Aric Lu Kaeini Ekong 1 Table of Contents Lab 1: Intro 3 Lab 2: Resistive Circuits

More information

Chapter 3, Sections Electrical Filters

Chapter 3, Sections Electrical Filters Chapter 3, Sections 3.2.4-3.2.5 Electrical Filters Signals DC and AC Components - Many signals can be constructed as sums of AC and DC components: 2.5 2 1.5 2 1.5 1.5 1 2 3 4 1.5 -.5-1 1 2 3 4 = + 2.5

More information

Lab #2: Electrical Measurements II AC Circuits and Capacitors, Inductors, Oscillators and Filters

Lab #2: Electrical Measurements II AC Circuits and Capacitors, Inductors, Oscillators and Filters Lab #2: Electrical Measurements II AC Circuits and Capacitors, Inductors, Oscillators and Filters Goal: In circuits with a time-varying voltage, the relationship between current and voltage is more complicated

More information

OPERATIONAL AMPLIFIER PREPARED BY, PROF. CHIRAG H. RAVAL ASSISTANT PROFESSOR NIRMA UNIVRSITY

OPERATIONAL AMPLIFIER PREPARED BY, PROF. CHIRAG H. RAVAL ASSISTANT PROFESSOR NIRMA UNIVRSITY OPERATIONAL AMPLIFIER PREPARED BY, PROF. CHIRAG H. RAVAL ASSISTANT PROFESSOR NIRMA UNIVRSITY INTRODUCTION Op-Amp means Operational Amplifier. Operational stands for mathematical operation like addition,

More information

(b) 25% (b) increases

(b) 25% (b) increases Homework Assignment 07 Question 1 (2 points each unless noted otherwise) 1. In the circuit 10 V, 10, and 5K. What current flows through? Answer: By op-amp action the voltage across is and the current through

More information

University of Jordan School of Engineering Electrical Engineering Department. EE 219 Electrical Circuits Lab

University of Jordan School of Engineering Electrical Engineering Department. EE 219 Electrical Circuits Lab University of Jordan School of Engineering Electrical Engineering Department EE 219 Electrical Circuits Lab EXPERIMENT 7 RESONANCE Prepared by: Dr. Mohammed Hawa EXPERIMENT 7 RESONANCE OBJECTIVE This experiment

More information

Class #16: Experiment Matlab and Data Analysis

Class #16: Experiment Matlab and Data Analysis Class #16: Experiment Matlab and Data Analysis Purpose: The objective of this experiment is to add to our Matlab skill set so that data can be easily plotted and analyzed with simple tools. Background:

More information

EECS 216 Winter 2008 Lab 3: AM Radio Part II: In-Lab & Post-lab Assignment

EECS 216 Winter 2008 Lab 3: AM Radio Part II: In-Lab & Post-lab Assignment EECS 216 Winter 2008 Lab 3: Part II: In-Lab & Post-lab Assignment c Kim Winick 2008 1 Introduction In this laboratory you will assemble and test a working superheterodyne AM radio consisting of a front-end

More information

LECTURER NOTE SMJE3163 DSP

LECTURER NOTE SMJE3163 DSP LECTURER NOTE SMJE363 DSP (04/05-) ------------------------------------------------------------------------- Week3 IIR Filter Design -------------------------------------------------------------------------

More information

PHYS 235: Homework Problems

PHYS 235: Homework Problems PHYS 235: Homework Problems 1. The illustration is a facsimile of an oscilloscope screen like the ones you use in lab. sinusoidal signal from your function generator is the input for Channel 1, and your

More information

University of Pittsburgh

University of Pittsburgh University of Pittsburgh Experiment #6 Lab Report Active Filters and Oscillators Submission Date: 7/9/28 Instructors: Dr. Ahmed Dallal Shangqian Gao Submitted By: Nick Haver & Alex Williams Station #2

More information

University of Michigan EECS 311: Electronic Circuits Fall 2008 LAB 2 ACTIVE FILTERS

University of Michigan EECS 311: Electronic Circuits Fall 2008 LAB 2 ACTIVE FILTERS University of Michigan EECS 311: Electronic Circuits Fall 2008 LAB 2 ACTIVE FILTERS Issued 9/22/2008 Pre Lab Completed 9/29/2008 Lab Due in Lecture 10/6/2008 Introduction In this lab you will design a

More information

DC and AC Circuits. Objective. Theory. 1. Direct Current (DC) R-C Circuit

DC and AC Circuits. Objective. Theory. 1. Direct Current (DC) R-C Circuit [International Campus Lab] Objective Determine the behavior of resistors, capacitors, and inductors in DC and AC circuits. Theory ----------------------------- Reference -------------------------- Young

More information

Lab 9 Frequency Domain

Lab 9 Frequency Domain Lab 9 Frequency Domain 1 Components Required Resistors Capacitors Function Generator Multimeter Oscilloscope 2 Filter Design Filters are electric components that allow applying different operations to

More information

Laboratory Project 4: Frequency Response and Filters

Laboratory Project 4: Frequency Response and Filters 2240 Laboratory Project 4: Frequency Response and Filters K. Durney and N. E. Cotter Electrical and Computer Engineering Department University of Utah Salt Lake City, UT 84112 Abstract-You will build a

More information

BME/ISE 3512 Bioelectronics. Laboratory Five - Operational Amplifiers

BME/ISE 3512 Bioelectronics. Laboratory Five - Operational Amplifiers BME/ISE 3512 Bioelectronics Laboratory Five - Operational Amplifiers Learning Objectives: Be familiar with the operation of a basic op-amp circuit. Be familiar with the characteristics of both ideal and

More information

Pre-Lab. Introduction

Pre-Lab. Introduction Pre-Lab Read through this entire lab. Perform all of your calculations (calculated values) prior to making the required circuit measurements. You may need to measure circuit component values to obtain

More information

BME/ISE 3512 Bioelectronics Laboratory Two - Passive Filters

BME/ISE 3512 Bioelectronics Laboratory Two - Passive Filters BME/ISE 35 Bioelectronics Laboratory Two - Passive Filters Learning Objectives: Understand the basic principles of passive filters. Supplies and Components: Breadboard 4.7 K Resistor 0.047 F Capacitor

More information

STUDY OF RC AND RL CIRCUITS Venue: Microelectronics Laboratory in E2 L2

STUDY OF RC AND RL CIRCUITS Venue: Microelectronics Laboratory in E2 L2 EXPERIMENT #1 STUDY OF RC AND RL CIRCUITS Venue: Microelectronics Laboratory in E2 L2 I. INTRODUCTION This laboratory is about verifying the transient behavior of RC and RL circuits. You need to revise

More information

6.002 Circuits and Electronics Final Exam Practice Set 1

6.002 Circuits and Electronics Final Exam Practice Set 1 MASSACHUSETTS INSTITUTE OF TECHNOLOGY DEPARTMENT OF ELECTRICAL ENGINEERING AND COMPUTER SCIENCE 6.002 Circuits and Electronics Set 1 Problem 1 Figure 1 shows a simplified small-signal model of a certain

More information

Experiment 2: Transients and Oscillations in RLC Circuits

Experiment 2: Transients and Oscillations in RLC Circuits Experiment 2: Transients and Oscillations in RLC Circuits Will Chemelewski Partner: Brian Enders TA: Nielsen See laboratory book #1 pages 5-7, data taken September 1, 2009 September 7, 2009 Abstract Transient

More information

Physics 5620 Laboratory 2 DC, RC and Passive Low Pass and High Pass Circuits

Physics 5620 Laboratory 2 DC, RC and Passive Low Pass and High Pass Circuits Physics 5620 Laboratory 2 D, and Passie Low Pass and High Pass ircuits Objectie: In this lab you will study D circuits using Kirchoff s laws and Theenin s theorem. You will also study the behaior of circuits

More information