SPECIFICATION ESD Released Date:2013/12/23-18:11:46

Size: px

Start display at page:

Download "SPECIFICATION ESD Released Date:2013/12/23-18:11:46"

Morgan Horton
5 years ago
Views:

1 SPECIFICATION ESD Released Date:2013/12/23-18:11:46

2 1/8 禁止翻印外洩 ESD R2.pdf 發行時間 :2013/12/23 全漢企業股份有限公司 FSP TECHNOLOGY INC. 台灣桃園市建國東路 22 號 NO.22,jianguo E,Rd.,Taoyuan City, Taiwan,R.O.C. TEL: FAX: SPECIFICATION FSP045-1SZ24-48 R&D CHECK APPROVED REV. Joge 02 1

3 2/8 禁止翻印外洩 ESD R2.pdf 發行時間 :2013/12/23 The spec. change list Item Revision Descriptions Date 1 01 Initial spec. release 12/ Model name revise. 03/ Add C.V mode. 10/

4 3/8 禁止翻印外洩 ESD R2.pdf 發行時間 :2013/12/23 1. SCOPE FSP045-1SZ24-48 is a 45.6Watts Single output, full range input and isolation switching power supply with PFC, Which could be used on the LED lighting products. Note: The LED is the abbreviation of Light-Emitting Diode. 2. GENERAL REQUIREMENTS All products including samples delivered will meet all the requirements as outlined in the document. The basic requirements of the design features are listed below: * Output forward voltage: 36V ~ 48V * Short circuit protection / open circuit / Fuse protection * High PFC 0.90 at 110Vac/ 220Vac * High reliability * High efficiency, greater than 88% efficiency@220vac * Wide input range capability option * Meet line harmonics in accordance with EN class-c for lightning application 3. MECHANICAL REQUIREMENTS 3.1 Power Supply Connectors AC Input: (CN100) AC input connector: JOWLE,3.96mm,3PIN,180',C/O 2,A3963WV2-A3P-D Pin assignment as below Pin-No. Name Remark 1 Neutral Line -- 3

5 LED output: (CN200) LED output connector: JOWLE,3.96mm,2PIN,180',3.7*7.7,A3963WV2-2P Pin assignment as below Pin-No. Name Remark 1 LED LED Power supply Dimension Constraints 101.6mm(L)*50.8mm(W)*28mm(H) Please check the outline drawing for detail 4 4/8 禁止翻印外洩 ESD R2.pdf 發行時間 :2013/12/23

6 5/8 禁止翻印外洩 ESD R2.pdf 發行時間 :2013/12/23 4. ELECTRICAL REQUIREMENTS 4.1 Input AC Input voltage Minimum Nominal Maximum / VAC Input Frequency Min Nominal Max 47 50/60 63 Hz 4.2 Output voltages and loads Constant Current Mode Signal Voltage (Volts) Name Current (ma) Min Typ Max Min. Typ Max. LED Constant Voltage Mode Signal Voltage (Volts) Name Current (ma) Min Typ Max Min. Typ Max. LED Note: 1. Output voltage will change according to LEDs series forward voltage. 2. The no load output voltage 55V at any AC input condition. 3. The Constant Voltage Mode (C.V) Power turn on Von point: 25V. 5

7 4.3 Protection Short Circuit Protection LED output have short circuit protection. A short condition on any of output shall cause no damage to the power supply. The unit shall recover and function automatically as soon as the short condition is removed LED Open Circuit When Series LED open circuit Note: When one output short circuit or over voltage protection.the other output won t be effected by the fault output Fuse protection The Fuse inside the power supply shall open when the AC input current is over the rated current of fuse. This Fuse protection will cause switching power supply to fail. 4.4 Efficiency Efficiency: >87% under 110Vac. >88% under 220Vac. Load: Max. Load Note: Power supply shall burn in at least 15 min. to get the correct data of efficiency. 4.5 Mean Time Between Failure (MTBF) 100,000hrs at 25 Degrees centigrade when calculated using MIL-HDBK-217F. Use agreed upon F.I.T. (failure - in - time) number in place of MTBF. 4.6 AC turn on time AC turn on time for LED shall less than 1 sec. 4.7 Ripple and Noise Table.2 lists the Ripple and Noise limitations of switching power supply unit only under all operating conditions including the input line voltage range and over all the full load range. Table.2 Ripple and Noise Limitations 6 6/8 禁止翻印外洩 ESD R2.pdf 發行時間 :2013/12/23

8 7/8 禁止翻印外洩 ESD R2.pdf 發行時間 :2013/12/23 Output Voltage Ripple & Noise (Vp-p) +48V 4.8 Note: 1. The measuring is done by 20MHz bandwidth limited oscilloscope while operating at loads between minimum to maximum load rating. 2. While test ripple noise of the output the probe shall avoid any coupling from other circuit or equipment.or the test result will not show power supply s actual ripple / noise. 3. Output shall be by passed at connector with C1 47uF/50V electrolytic capacitor and C2 0.1uF/50V ceramic disk capacitor. Test Measure Devi C1 C2 S.P. * C1,C2 see the Tabl 5. ENVIRONMENTAL REQUIREMENTS 5.1 Operating Temperature Power Operating -20 to +60 C Storage -30 to +85 C The operation temperature is the temperature around the power supply. If the power supply put inside the enclosure chassis. The outside temperature shall not cause the inside temperature exceed max. operation temperature. 5.2 Humidity (Non-condensing) Power Operating Storage 20% to +85%RH 0% to +95%RH 7

9 8/8 禁止翻印外洩 ESD R2.pdf 發行時間 :2013/12/23 6. EMC AND SAFETY REQUIREMENT 6-1 EMI Standards Designed to meet the following conducted & radiation limits: EN EMS Standards Electrostatic Discharge Immunity Test IEC Contact: 4KV, Air: 8KV, Criteria B EFT/Burst Immunity Test IEC KV, Criteria B Surge Immunity Test IEC KV, Criteria B 6.3 PFC (Power factor correction) and Harmonics Power supply shall design with PFC circuit and meet IEC Class C. 6.4 Safety Compliance Design to meet IEC Hi-pot test 100% Hi-pot tested, Primary to second: 3750VAC 60 second, cut off current shall less than 5mA. Primary to FG: 1875VAC 60 second, cut off current shall less than 5mA Leakage Current Test Leakage Current: Measured at 220Vac, 50Hz, 0.75mA max Insulation Test Insulation resistance: Primary to Secondary: 500Vdc, 25M ohms min. 7. ROHS COMPLIANT All the component of the power supply have to be RoHS compliant. 8

SPECIFICATION ESD FSP250-60HNC. Released Date:2012/08/15-21:58:49

SPECIFICATION ESD FSP250-60HNC. Released Date:2012/08/15-21:58:49 SPECIFICATION ESD12047757 FSP250-60HNC Released Date:2012/08/15-21:58:49 1/9 禁止翻印外洩 ESD12047757-R1.pdf 發行時間 :2012/8/15 全漢企業股份有限公司 FSP TECHNOLOGY INC. 台灣桃園市建國東路 22 號 NO.22,Jianguo E, Rd.,Taoyuan City,Taiwan,R.O.C.