Reference Standard Models RS 2120 RS 2320

Transcription

1 Reference Standard Models RS 2120 RS 2320 Version 3.2c

2 Content Reference Standard RS 2x20 1. Introduction Device Hardware Overview Front Side Rear Side Device Software Overview Measurement Energy Measurement Graphical presentation Menu Measurement Settings System Settings Information Screen Remote Interface Connection to PC Remote Communication Commands Summary Commands Description RS2x20-UG32c-EN

3 1. Introduction Reference Standard RS 2x20 Reference Standard RS 2320 The Reference Standard RS 2x20 is a precision single-phase (RS 2120) or three-phase (RS 2320) reference meter for electrical power and energy measurement up to 120 A. Measurement based on precision A/D conversion and DSP technology enables accurate high-speed real time evaluation of all main and informative quantities. Beyond measurement of power, voltage, current and phase the device indicates voltage sequence and registers active, reactive and apparent energy. Device measures and graphically displays distortion and wave-form of measured signals. RS2x20-UG32c-EN 3

4 2. Device Hardware Overview Reference Standard RS 2x Front Side Front side of RS 2320B 2.2 Rear Side Rear side of RS 2320B Mains Case/Earth GND - Power supply - Metal parts of the device case and the guard wire of the network socket - Ground for digital and analogue circuits RS232 - Communication bus RS 232 USB - Communication bus USB AUX F IN F OUT - Auxiliary connector (unused prepared for future) - Frequency input (unused prepared for future) - Frequency output L1, L2, L3 - Three measurement channels In - Current input connectors (red) Out - Current output connectors (black) U - Active voltage terminals N - Reference voltage terminal (common for all channels) 4 RS2x20-UG32c-EN

5 3. Device Software Overview Reference Standard RS 2x20 The device is equipped with color 3.5 TFT LCD display and alpha-numeric keyboard. Screen is divided into 3 zones: Header Info page name keyboard mode measured values calculated values graphs parameters etc. Functions graphical presentation of functions of keys F1 F Measurement Main page for RS 2120 Load Values shows actual measured and calculated values: List of displayed quantities: U... Voltage I... Current P... Active Power Q... Reactive Power S... Apparent Power λ... Power Factor φ... Current Phase f... Frequency RS Load Values page Control keys: F1... Energy Values F2... Vector Diagram F3... Harmonics F4... Menu RS2x20-UG32c-EN 5

6 Main page for RS 2320 Load Values shows actual measured and calculated values: List of displayed quantities: U... Voltage I... Current P... Active Power Q... Reactive Power S... Apparent Power λ... Power Factor... Voltage Phase... Current Phase f... Frequency L1xx... Phase Sequence (L123 or L132) RS Load Values page Control keys: F1... Energy Values F2... Vector Diagram F3... Harmonics F4... Menu Next pages Load Values: RS Load Values page L1 RS Load Values page L2 6 RS2x20-UG32c-EN

7 RS Load Values page L3 Control keys: F1... Energy Values F2... Vector Diagram F3... Harmonics F4... Menu RS2x20-UG32c-EN 7

8 3.1.1 Energy Measurement Page Energy Values can be accessed from Load Values page using key F1 and shows measured and calculated energy values. Active, reactive and apparent energies are accumulated beside the measurement and shown on this page. Accumulation of these energies can be stopped and started again (key F2) or just restarted by key F3. RS Energy Values page List of displayed quantities: U... Voltage I... Current ΣP... Sum of Active Powers ΣQ... Sum of Reactive Powers ΣS... Sum of Apparent Powers E P... Active Energy E Q... Reactive Energy E S... Apparent Energy ΣE P... Sum of Active Energies ΣE Q... Sum of Reactive Energies ΣE S... Sum of Apparent Energies f... Frequency L1xx... Phase Sequence (L123 or L132) List of displayed quantities: U... Voltage I... Current P... Active Power Q... Reactive Power S... Apparent Power E P... Active Energy E Q... Reactive Energy E S... Apparent Energy RS Energy Values page Control keys: F1... Load Values page F2... Stop / start online energy accumulation F3... Clear energy registers F4... Menu 8 RS2x20-UG32c-EN

9 3.1.2 Graphical presentation Graphical Presentation pages which can be activated from Energy Values page by repeated usage of F1 key show graphical presentation of measured signals. Vector Diagram page Harmonics page Curve page Harmonics View RS2x20-UG32c-EN 9

10 Vector diagram has two parameters which can be configured in Measurement Settings: position of reference zero axis (vertical or horizontal) reference unit (voltage or current) which is displayed on reference zero axis Harmonics screen shows harmonics up to 31 st harmonic. 10 harmonics are displayed on one screen. Scrolling to other harmonics can be done by arrow keys. Combination of showed signals (I1+I2+I3, U1+U2+U3, U1+I1, U2+I2 or U3+I3) can be in Harmonics and Curve screens chosen by arrow keys in Harmonics and Curve pages. Harmonics View screen shows measured values (amplitude and phase) of all harmonics. Control keys (for three graphical presentation pages): F1... Switch to another graphical presentation pages or back to main page F2... Show Harmonics View in Harmonics screen F4... Menu... Choose combination of showed signals in Harmonics and Curve screens... Scroll next/previous 10 harmonics in Harmonics screen ESC... Exit (return to main measurement page) Control keys (for Harmonics View screen): F1, ESC... Exit (return back to Harmonics screen) F2... Switch to next channel (L1<->L2<->L3<->L1) F3... Switch to next channel (U<->I<->U)... Scrolling of content PgDn, PgUp... Paging of content 10 RS2x20-UG32c-EN

11 3.2 Menu Menu enables access to settings, database, information about device and device calibration. It can be activated by key F4. Menu page Content: 1. Measurement Settings... measurement settings 2. System Settings... system settings 3. Info... information about the device 4. Calibration... calibration of the device Control keys: F1 or 1... measurement settings F2 or 2... system settings F3 or 3... info F4 or 4... calibration Down, Up... movement on screen OK... confirmation of selected item ESC... exit of menu RS2x20-UG32c-EN 11

12 3.2.1 Measurement Settings Measurement Settings page contains parameters of measurement mode. Page is showed in two screens and switching between them is done by key F4. Measurement Settings page 1/3 Measurement Settings page 2/3 Content: Measurement Settings page 3/3 ENERGY OUTPUT... settings of energy (impulse) output State... type of measured energy: Active, Reactive or Apparent Energy or Fixed frequency Fixed freq.... value of fixed frequency generated on red impulse LED or on connected BNC cable if parameter State has value Fixed frequency Factor... constant of device WS Factor unit... unit of parameter Factor: i/kwh, i/wh, i/ws, i/kws, kwh/i, Wh/i, Ws/i or kws/i AUX output... enable or disable the AUX output for currently measured signal Channel Lx... selection of individual channels (L1, L2 or L3) for impulse output functions. The value of the parameter is ON or OFF for the switchedon or switched-off selection of the appropriate channel, respectively. 12 RS2x20-UG32c-EN

13 Connect. type... connection type: 3P4W, 3P3W, 2P3W or 1P2W (see appendix Connecting device chapter) RANGE (Input A / Input B)... settings of ranges Auto... automatic range selection: ON (enabled) or OFF (disabled). Device chooses best suitable range depending on measured values if automatic range selection is enabled. Value... manually selected range (valid if parameter Auto is OFF) VECTOR DIAGRAM... settings of vector diagram displaying Zero axis... position of reference zero axis: Vertical or Horizontal Reference... reference unit: Voltage or Current FREQUENCY... settings of frequency measurement Default freq.... default measurement frequency: 50 or 60 Hz Sync. chnl.... synchronization channel used for frequency measurement: UL1, UL2, UL3, IL1, IL2, IL3 or AUTO (selection depending on amplitude) ENERGY MEASUREMENT... settings of energy measurement Unit... unit of energy: Ws or kwh REACTIVE POWER MEAS... Setting of reactive power measurement Method... Measurement method: True or Cross connected Control keys: F1, ESC... Exit (return to previous page) F2... Load default values (only for parameters in shown page!) F3... Save actual values of all Measurement Settings parameters into memory (saved values will be loaded after next switch on) F4... Switching between screens 1/3, 2/3 and 3/3 RS2x20-UG32c-EN 13

14 3.2.2 System Settings System Settings page contains general parameters of the system of the device. Page is showed in two screens and switching between them is done by key F4. Content: System Settings screen 1/2 System Settings screen 2/2 Language... selection of language of devices user interface BAUDRATE... settings of baud rate of device communication interfaces RS baud rate of RS-232 communication interface: 300, 600, 1200, 2400, 4800, 9600, 19200, 28800, 38400, or USB... baud rate of USB communication interface: 300, 600, 1200, 2400, 4800, 9600, 19200, 28800, 38400, or DISPLAY... Setting of display content Resolution... Resolution of showed measured and calculated values in one phase screens: Standard (5 digits), High (6 digits) or Maximal (7 digits) Warnings... Enable (ON) / disable (OFF) showing of system warnings (and errors) BACKLIGHT... settings of backlight of display Intensity... backlight intensity: 10%, 20% 90% or 100% Auto off timeout... automatic backlight switch-off time: 1 / 2 / 5 / 10 / 20 / 30 min or OFF (inactive) SOUNDS... settings of sounds Keypad beep... acoustic indication of keys pressing: ON or OFF Control keys: F1, ESC... Exit (return to previous page) F2... Load default values (only for parameters in shown screen!) F3... Save actual values of all System Settings parameters into memory (saved values will be loaded after next switch on) F4... Switching between screens 1/2 and 2/2 14 RS2x20-UG32c-EN

15 3.2.3 Information Screen Information screen shows basic information about the device and connected accessories. Page is showed in two screens and switching between them is done by key F4. Information screen 1/3 Information screen 2/3 Information screen 3/3 RS2x20-UG32c-EN 15

16 Content: Reference Standard RS 2x20 DEVICE... type of the device Serial No.... serial number of the device HW1 ver.... hardware version of upper (high level) part of the device HW2 ver.... hardware version of bottom (low level) part of the device FW1 ver.... firmware version of upper (high level) part of the device FW2 ver.... firmware version of bottom (low level) part of the device GUI ver.... version of user interface screens (Graphical User Interface) POWER SUPPLY... auxiliary voltages (specified for diagnostic purposes) Voltage 1... power supply voltage 1 Voltage 2... power supply voltage 2 Voltage 3... power supply voltage 3 INPUT A... type of the voltage input Serial No.... serial number of the voltage input Ranges... ranges of the voltage input INPUT B... type of the current input Serial No.... serial number of the current input Ranges... ranges of the current input Control keys: F1, ESC... exit of the screen F4... switching between screens 1/2 and 2/2 16 RS2x20-UG32c-EN

17 4. Remote Interface 4.1 Connection to PC Device can be connected to computer via communication interface USB or RS-232. Reference Standard RS 2x20 Driver required for connection of RS 2x20 to PC via USB communication interface is FTDI Virtual COM port (VCP) driver (Not Microsoft WHQL certified) Newest version of required driver is available from FTDI website: Maybe not actual but tested version of driver is available in Applied Precision s website from link: After unpacking the zip file and successful installation of the driver new virtual COM port will appear in operating system. For communication with the device the correct COM port have to be chosen in PC in communication software. 4.2 Remote Communication Device control, results readout and measured values collection remotely is performed using device commands compatible with SCPI standard (Standard Commands for Programmable Instruments). Main rules of SCPI standard: parentheses { } restrict parameter in the command strain parentheses [ ] restrict optional parameters or parts of commands parentheses < > restrict parameter, which is due to be replaced by the value perpendicular line ( ) separate options, from which exactly one has to be chosen character case in the command is optional (command SYST:VERS? is identical with syst:vers?) RS2x20-UG32c-EN 17

18 *IDN? *RST SYST MEAS Commands Summary :ERR? :SERN? :VERS? :HWV? :DATV? :CLAS? :TIM? :TIM :SET:COM :SET:COM? :SET:COM1? :SET:COM1 {<baudrate ( )>} :SET:COM2? :SET:COM2 {<baudrate ( )>} :CONF:SAVE :CONF:LOAD :VOLT:AC? :VOLT:AC:PHAS? :VOLT:AC:SUM:SQ? :CURR:AC? :CURR:AC:PHAS? :CURR:AC:SUM:SQ? :POW:AC[:ACT]? :POW:AC:REAC? :POW:AC:APP? :POW:AC:FACT? :POW:AC:SUM:ACT? :POW:AC:SUM:REAC? :POW:AC:SUM:APP? :FREQ? :ENER:STAR :ENER:STOP :ENER:RES :ENER:STAT? :ENER:ACT? :ENER:ACT:K? :ENER:REAC? :ENER:REAC:K? :ENER:APP? :ENER:APP:K? :SIGN? {<phase (0 1 2)>},{<unit (0 1)>},{<harmonic (0-31)>} 18 RS2x20-UG32c-EN

19 *IDN? Request for the device identification string Commands Description *RST Device reset. This command has the same effect as the GPIB bus system command DCL. SYST:ERR? Request for the error announcement from the error announcement register. This register is a FIFO type (=first in first out). SYST:SERN? Request for the device serial number. SYST:VERS? Request for the device firmware version. SYST:HWV? Request for the device hardware version. SYST:DATV? Request for the version of data memory. SYST:CLAS? Request for the device class. SYST:TIM? Request for device s date & time. SYST:TIM {<date&time>} Setting of date & time of the device. Parameter have to be in format YYYY-MM-DD hh:mm:ss. Example: " :55:20". SYST:SET:COM1? Request for the actual speed (baud rate) of serial communication. SYST:SET:COM1 {<baudrate ( )>} Setting of speed (baud rate) of serial communication. Allowed baud rate values are : 1200, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, RS2x20-UG32c-EN 19

20 Measurement Commands Measurement commands return measured values in form of a set of three real numbers without unit. Values are in classic or exponential format (depends on value and firmware version) with max. 6 decimal places and separation of decimal part of number is made by point. Three values are separated by comma or comma followed by space (depends on firmware version). Examples of return string: , , E-03, E-03, E-03 MEAS:VOLT:AC? Request for voltage values. MEAS:VOLT:AC:PHAS? Request for phases between voltages. MEAS:VOLT:AC:SUM:SQ? Request for sum of square voltages. MEAS:CURR:AC? Request for current values. MEAS:CURR:AC:PHAS? Request for phases between current and voltage in each phase. MEAS:CURR:AC:SUM:SQ? Request for sum of square currents. MEAS:POW:AC[:ACT]? Request for active power values. MEAS:POW:AC:REAC? Request for reactive power values. MEAS:POW:AC:APP? Request for apparent power values. MEAS:POW:AC:FACT? Request for power factors. MEAS:POW:AC:SUM:ACT? Request for sum of active powers. MEAS:POW:AC:SUM:REAC? Request for sum of reactive powers. MEAS:POW:AC:SUM:APP? Request for sum of apparent powers. MEAS:FREQ? Request for frequency. MEAS:ENER:STAR Start of energy accumulation (if stopped). MEAS:ENER:STOP Stop of energy accumulation (if started). MEAS:ENER:RES Reset (clearing to zero) of energy accumulation values. 20 RS2x20-UG32c-EN

21 MEAS:ENER:STAT? Request for status of energy accumulation. Answer is 0 (stopped) or 1 (started). MEAS:ENER:ACT? Request for active energy values in Ws. MEAS:ENER:ACT:K? Request for active energy values in kwh. MEAS:ENER:REAC? Request for reactive energy values in vars. MEAS:ENER:REAC:K? Request for reactive energy values in kvarh. MEAS:ENER:APP? Request for apparent energy values in VAs. MEAS:ENER:APP:K? Request for apparent energy values in kvah. MEAS:SIGN? {<phase (0 1 2)>},{<unit (0 1)>},{<harmonic (0-31)>} Request for signal s harmonic content. Parameters : phase (0=L1, 1=L2, 2=L3), unit (0=U, 1=I) and harmonic number. Answer : amplitude and phase (two comma separated real numbers). Examples: MEASure:SIGNal? 0,0,2 reading of content of 2 nd harmonic of U L1 MEASure:SIGNal? 2,1,5 reading of content of 5 th harmonic of I L E-01, E+01 answer for MEASure:SIGNal? command RS2x20-UG32c-EN 21

22 Manufacturer s Name: Reference Standard RS 2x20 DECLARATION OF CONFORMITY Applied Precision Ltd. Manufacturer s Address: Stavitelska Bratislava SLOVAKIA Declares, that the product Product Name: Model Number(s): Product Option(s): Reference Standard RS 2120B, RS 2320B all options of the above product Conforms to the following European Directives: Low Voltage Directive: 2006/95/EC (dated ) EMC Directive: 2004/108/EC (dated ) Conforms to the following product standards: Safety: EN (dated 2001/2002/2003) EMC: EN (dated 1997) Product is safe under conditions of standard application and carries the CE marking 11 th December 2009 DATE Dr. Ladislav GRNO Director 22 RS2x20-UG32b-EN

23 TECHNICAL SPECIFICATION Model Phases Class RS 2120B RS 2320B Basic Error Voltage & Current 0.05 % Apparent Power 0.1 % Active Power * 0.1 % Reactive Power * 0.2 % Power Factor Frequency 0.01 Hz Distortion 0.5 % Phase angle 0.1 * related to the Apparent Power General Parameters Voltage, Current, Active/Reactive/Apparent Power, Measured Quantities Active/Reactive/Apparent Energy, Power Factor, Phase Angle, Frequency, Distortion Basic Frequency Hz 1-phase 2-wire (RS 2120 & RS 2320) Input Circuits 1-phase 3-wire and 2-phase (RS 2320 only) 3-phase 3-wire / 4-wire (RS 2320 only) Voltage Range V (phase to neutral) Current Range 1 ma A Power Factor Range Phase Angle Communication Interface USB and RS-232 (SCPI compatible communication protocol) Meter Testing direct testing of inductive or electronic meters or reference standards Display 3.5 / 320 x 240 pixels / 256 colors Dimensions (W x D x H) 490 x 490 x 90 mm (2U form factor) Weight (approx.) 9.5 kg (RS 2120) 10.5 kg (RS 2320) Impulse Output Number of impulse outputs 1 Impulses assigned to Active / Reactive / Apparent Energy or programmable constant frequency Meter constant programmable Maximal impulse frequency 70 khz 23 RS2x20-UG32b-EN