TITLE MICROCIRCUIT, DIGITAL, 9 CHANNEL RS- 422/ RS-485 TRANSCEIVER, MONOLITHIC SILICON REVISIONS LTR DESCRIPTION DATE APPROVED
|
|
- Neil Bates
- 5 years ago
- Views:
Transcription
1 REISIONS LTR DESCRIPTION DTE PPROED Correc vendor par in secion phn Thomas M. Hess B Updae boilerplae o curren MIL-PRF requiremens. - PHN Thomas M. Hess Prepared in accordance wih SME Y14.24 endor iem drawing RE PGE RE PGE RE STTUS OF PGES RE B B B B B B B B B B B B B B PGE PMIC N/ Original dae of drawing YY MM DD PREPRED BY Phu H. Nguyen CHECKED BY Phu H. Nguyen PPROED BY Thomas M. Hess TITLE DL LND ND MRITIME hp:// MICROCIRCUIT, DIGITL, 9 CHNNEL RS- 422/ RS-485 TRNSCEIER, MONOLITHIC SILICON CODE IDENT. NO. RE B PGE 1 OF 14 MSC N/ DISTRIBUTION STTEMENT. pproved for public release. Disribuion is unlimied
2 1. SCOPE 1.1 Scope. This drawing documens he general requiremens of a high performance 9 channel RS-422/ RS-485 ransceiver microcircui, wih an operaing emperaure range of -40 C o +85 C. 1.2 endor Iem Drawing dminisraive Conrol Number. The manufacurer s PIN is he iem of idenificaion. The vendor iem drawing esablishes an adminisraive conrol number for idenifying he iem on he engineering documenaion: Device ype(s) X E Drawing Device ype Case ouline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) Device ype Generic Circui funcion 01 SN65HD09-EP 9 channel RS-422/ RS-485 ransceiver Case ouline(s). The case oulines are as specified herein. Ouline leer Number of pins JEDEC PUB 95 Package syle X 56 JEDEC MO-153 Plasic small ouline Lead finishes. The lead finishes are as specified below or oher lead finishes as provided by he device manufacurer: Finish designaor B C D E F Z Maerial Ho solder dip Tin-lead plae Gold plae Palladium Gold flash palladium Tin-lead alloy Oher DL LND ND MRITIME RE B PGE 2
3 1.3 bsolue maximum raings. 1/ Supply volage range, (CC) o 6.0 2/ Bus volage range o 15 Daa I/O and conrol ( side) volage range o CC Receiver oupu curren (IO)... ±40 m Elecrosaic discharge: B side and GND, ESD HBM k B side and GND, ESD MM ll erminals, ESD HBM... 4 k ll erminals, ESD MM Coninuous oal power dissipaion... Inernally limied 3/ Dissipaion raings Thermal characerisics Package T 25 C Operaing facor 4/ above T = 25 C T = 70 C Power raing T = 70 C Power raing Case X 2500 mw 20 mw/ C 1600 mw 1300 mw Typical Juncion o ambien hermal resisance (θj) 50 C/W Juncion o case (op) hermal resisance (θj) 27 Thermal shudown emperaure (TSD) 165 C 1.4 Recommended operaing condiions. Supply volage, (CC) o 5.25 Minimum high level inpu volage, (IH) (excep nb+, nb-) 5/ Maximum low level inpu volage, (IL) (excep nb+, nb-) 5/ olage a any bus erminal, (O, I, IC) (separaely or common mode) (nb+ or nb-) o 12.0 Oupu curren: Driver m o 60 m Receiver m o 8 m Operaing free air emperaure, (T) C o 85 C 2. PPLICBLE DOCUMENTS JEDEC SOLID STTE TECHNOLOGY SSOCITION (JEDEC) JEP95 Regisered and Sandard Oulines for Semiconducor Devices (pplicaions for copies should be addressed o he Elecronic Indusries lliance, 3103 Norh 10h Sree, Suie 240 S, rlingon, or online a hps:// Uni 1/ Sresses beyond hose lised under absolue maximum raings may cause permanen damage o he device. These are sress raings only, and funcional operaion of he device a hese or any oher condiions beyond hose indicaed under recommended operaing condiions is no implied. Exposure o absolue maximum raed condiions for exended periods may affec device reliabiliy. 2/ ll volage values are wih respec o he GND erminals. 3/ The maximum operaing juncion emperaure is inernally limied. Use he Dissipaion Raing Table o operae below his emperaure. 4/ This is inverse of he juncion o ambien emperaure when board mouned and wih no air flow. 5/ n = 1 9. DL LND ND MRITIME RE B PGE 3
4 3. REQUIREMENTS 3.1 Marking. Pars shall be permanenly and legibly marked wih he manufacurer s par number as shown in 6.3 herein and as follows:. Manufacurer s name, CGE code, or logo B. Pin 1 idenifier C. ESDS idenificaion (opional) 3.2 Uni conainer. The uni conainer shall be marked wih he manufacurer s par number and wih iems and C (if applicable) above. 3.3 Elecrical characerisics. The maximum and recommended operaing condiions and elecrical performance characerisics are as specified in 1.3, 1.4, and able I herein. 3.4 Design, consrucion, and physical dimension. The design, consrucion, and physical dimensions are as specified herein. 3.5 Diagrams Case ouline. The case ouline shall be as shown in and figure connecions. The erminal connecions shall be as shown in figure funcion. The erminal funcion shall be as shown in figure Logic diagram. The logic diagram shall be as shown in figure Driver es circui, RS-422 and RS-485 loading. The driver es circui, RS-422 and RS-485 loading shall be as shown in figure Driver es circui, pull-up and pull down loading. The driver es circui, pull-up and pull-down loading shall be as shown in figure Driver delay and ransiion ime es waveforms. The Driver delay and ransiion ime es waveforms shall be as shown in figure Receiver propagaion delay and ransiion ime es circui. The receiver propagaion delay and ransiion ime es circui shall be as shown in figure Receiver delay and ransiion ime waveforms. The receiver delay and ransiion ime waveforms shall be as shown in figure Driver enable and disable ime es circui. The driver enable and disable ime es circui shall be as shown in figure Driver enable ime waveforms. The driver enable ime waveforms shall be as shown in figure Receiver enable and disable ime es circui. The receiver enable and disable ime es circui shall be as shown in figure Receiver enable and disable ime waveforms. The receiver enable and disable ime waveforms shall be as shown in figure 13. DL LND ND MRITIME RE B PGE 4
5 Driver differenial oupu volage magniude TBLE I. Elecrical performance characerisics. 1/ Tes Symbol Condiions DD Limis 2/ Min Max RS-422 load RL = 100 Ω See figure RS-485 load RL = 54 Ω 1.4 TYP Pull up Pull-down load See figure 6 1 High level oupu volage OH side, IOH = -8 m, ID = 200 m See figure 8 4 B side, See figure 6 3 TYP Low level oupu volage OL side, IOH = 8 m, ID = -200 m See figure Receiver posiive going differenial inpu hreshold volages Receiver negaive going differenial inpu hreshold volages Receiver inpu hyseresis (IT+ - IT-) Bus inpu curren B side, See figure 6 1 TYP IT+ IOH = -8 m See figure IT- IOH = 8 m See figure hys CC = 5, T = 25 C 24 m II IH = 12, CC = 5 IH = 12, CC = 0 1 Oher inpu a 0 IH = -7, CC = IH = -7, CC = Uni 1 m High level inpu curren n, BSR, DE/RE, and CRE, IIH IH = µ CDE0, CDE1, and CDE2 IH = Low level inpu curren n, BSR, DE/RE, and CRE, IIL IH = CDE0, CDE1, and CDE2 IH = Shor circui oupu curren IOS nb+ on nb- ±260 m High impedance sae oupu curren Supply curren IOZ ICC n nb+ or nb- See IIH and IIL See III Disabled 10 m ll drivers enabled, no load 60 ll receivers enabled, no load 45 Oupu capaciance CO nb+ or nb- o GND 18 TYP pf Power dissipaion capaciance 3/ Cpd Receiver 40 TYP pf Driver 100 TYP See foonoe a end of able. DL LND ND MRITIME RE B PGE 5
6 TBLE I. Elecrical performance characerisics - Coninued. 1/ Driver swiching characerisics Tes Symbol Condiions Propagaion delay ime, PHL or PLH (see figure 6 and 7) pd ns Pulse skew, PHL - PLH sk(p) 5 2/ Limis Fall ime f S1 o B, See figure 7 4 TYP Rise ime r See figure 7 8 TYP Enable ime, conrol inpus o acive oupu en 50 Disable ime, conrol inpus o high impedance oupu dis 225 Propagaion delay ime, high level o high impedance oupu PHZ See figure 10 and Propagaion delay ime, low level o high impedance oupu PLZ 225 Propagaion delay ime, high impedance o high level oupu PZH 50 Propagaion delay ime, high impedance o low level oupu PZL 50 Receiver swiching characerisics Propagaion delay ime, PHL or PLH (see figure 6 and 7) pd ns Skew limi, maximum pd minimum pd 4/ sk(lim) 5 Pulse skew, PHL - PLH sk(p) 5 Transiion ime (r or f) See figure 9 2 TYP Enable ime, conrol inpus o acive oupu en 31 TYP Disable ime, conrol inpus o high impedance oupu dis 41 TYP Propagaion delay ime, high level o high impedance oupu PHZ See figure 12 and TYP Propagaion delay ime, low level o high impedance oupu PLZ 14 TYP Propagaion delay ime, high impedance o high level oupu PZH 30 TYP Propagaion delay ime, high impedance o low level oupu PZL 30 TYP 1/ Tesing and oher qualiy conrol echniques are used o he exen deemed necessary o assure produc performance over he specified emperaure range. Produc may no necessarily be esed across he full emperaure range and all parameers may no necessarily be esed. In he absence of specific parameric esing, produc performance is assured by characerizaion and/or design. 2/ Over recommended operaing free air emperaure range (unless oherwise noed). ll ypical values are wih respec o CC = 5, and T = 25 C. 3/ Cpd deermines he no-load dynamic supply curren consumpion, IS = CPD x CC x f + ICC. 4/ This parameer is applicable a one CC and operaing emperaure wih he recommended operaing condiions and o any wo devices. Min Max Uni DL LND ND MRITIME RE B PGE 6
7 Case X e b 0.08 M c E1 E GGE PLNE 1 28 L 0.25 DETIL D SEE DETIL 1 SETING PLNE 0.10 Dimensions Symbol Millimeers Symbol Millimeers Min Max Min Max 1.20 E E b e 0.50 TYP c 0.15 NOM L D NOTES: 1. ll linear dimensions are in millimeers. 2. This drawing is subjec o change wihou noice. 3. Body dimensions do no include mold prorusions no exceed Falls wihin JEDEC MO-153. FIGURE 1. Case ouline. DL LND ND MRITIME RE B PGE 7
8 Name number symbol number symbol Case ouline X number symbol number symbol 1 GND 15 GND 29 1B- 43 GND 2 BSR 16 GND 30 1B+ 44 GND 3 CRE 17 GND 31 2B- 45 CC CC 32 2B+ 46 6B- 5 1DE/RE B- 47 6B DE/RE 34 3B+ 48 7B- 7 2DE/RE B- 49 7B+ 8 CC 22 6DE/RE 36 4B+ 50 8B- 9 3DE/RE B- 51 8B DE/RE 38 5B+ 52 9B- 11 4DE/RE CC 53 9B+ 12 CC 26 8DE/RE 40 GND 54 CDE0 13 GND GND 55 CDE1 14 GND 28 9DE/RE 42 GND 56 CDE2 No. I/O FIGURE 2. connecions. Descripion 1 o 9 4, 6, 8, 10, 19,21, 23, I/O 25, 27 1 o 9 carry daa o and from he communicaion conroller 1b- o 9B- 29, 31, 33, 35, 37, I/O 46, 48, 50, 52 1B- o 9B- are he invered daa signals of he balanced pair o/from he bus 1B+ o 9B+ 30, 32, 34, 36, 38, I/O 47, 49, 51, 53 1B+ o 9B+ are he noninvered daa signals of he balanced pair o/from he bus BSR 2 I BSR is he bi significan response. BSR disables receivers 1 hrough 8 and enables wired OR drivers when BSR and DE/RE and CDE1 and CDE2 are high. Channel 9 is placed in a high impedance sae wih BSR high CDE0 54 I CDE0 is he common driver enable 0. Is inpu signal enables all drivers when CDE0 and 1DE/RE - 9DE/RE are high. CDE1 55 I CDE1 is he common driver enable 1. Is inpu signal enables drivers 1 o 4 when CDE1 is high and BSR is low. CDE2 56 I CDE2 is he common driver enable 2. When CDE2 is high and BSR is low, drivers 5 o 8 are enabled. CRE 3 I CRE is he common receiver enabled. When high, CRE diables receiver channel 5 o 9. 1DE/RE o 9DE/RE 5, 7, 9, 11, 20, 22, 24, 26, 28 I 1DE/RE - 9DE/RE are direcion conrols ha ransmi daa o he bus when i and CDE0 are high. Daa is received from he bus when 1DE/RE o 9DE/RE and CRE and BSR are low and CDE1 and CDE2 are low GND 1, 13, 14, 15, 16, 17, 40, 41, 42, 43, 44 Power CC 12, 18, 39, 45 Power Supply volage mus be conneced o signal ground for proper operaion. GND is he circui ground. ll GND erminals excep erminal 1 are physically ied o he die pad for improved hermal conduciviy. 1/ FIGURE 3. funcion. DL LND ND MRITIME RE B PGE 8
9 CDE0 CDE1 BSR 1 1B+ 1DE/RE 2 2DE/RE 3 3DE/RE 4 4DE/RE CHNNEL 2 CHNNEL 3 CHNNEL 4 CDE2 CRE 5 5B+ 6B+ 6B- 7B+ 7B- 8B+ 8B- 9B+ 9B- 5B- 5DE/RE 6 6DE/RE 7 7DE/RE 8 8DE/RE 4 9DE/RE CHNNEL 6 CHNNEL 7 CHNNEL 8 BSR BSR CRE CDE0 2B+ 2B- 3B+ 3B- 4B+ 4B- 1B- FIGURE 4. Logic diagram. DL LND ND MRITIME RE B PGE 9
10 R L /2 INPUT B+ B- R L /2 C L =50 pf ±20% OC C L INCLUDES FIXTURE ND INSTRUMENTTION CPCITNCE FIGURE 5. Driver es circui, RS-422 and RS 485 loading. 5 PU PD 165 INPUT SEE NOTE 1 I 1 I O B+ OD O 15 pf 75 S I I O B- S2 O 15 pf SEE NOTE 2 NOTES: 1. CDEO and DE/RE are a 2, BSR is a 0.8, and all ohers are open. 2. ll nine drivers are enabled, simply loaded, and swiching. FIGURE 6. Driver es circui, Pull up and pull down loading. 3 INPUT PLH PHL OUTPUT, OD r f OD(H) 90% 0 10% OD(L) S1 TO PU OR PD FIGURE 7. Driver delay and ransiion ime es waveforms. DL LND ND MRITIME RE B PGE 10
11 GENERTOR SEE NOTE 1 50 INPUT B+ I O ID OUTPUT GENERTOR SEE NOTE 1 INPUT B- 50 SEE NOTE 2 O C L =15 pf NOTES: 1. CDE0, CDE1, CDE2, BSR, CRE, and DE/RE are a ll nine receivers are enabled and swiching. FIGURE 8. Receiver propagaion delay and ransiion ime es circui. INPUT B INPUT B+ 0 PLH PHL OUTPUT r f OH 90% % OL NOTES: 1. ll inpu pulses are supplied by a generaor having he following characerisics: r 6 ns, f 6 ns, PRR 1 MHz, duy cycle = 50%, ZO = 50 Ω. 2. ll resisances are in Ω and ±5%, unless oherwise indicaed. 3. ll capaciances are in pf and ±10%, unless oherwise indicaed. 4. ll indicaed volages are ±10 m. FIGURE 9. Receiver delay and ransiion ime waveforms. 4.5 PU PD 165 B+ S OR 3 OD 50 pf DE/RE SEE TBLE 1 B- 50 SEE pf NOTE S2 INPUT NOTE: 1. Includes probe and jig capaciance in wo places. FIGURE 10. Driver enable and disable ime es circui. DL LND ND MRITIME RE B PGE 11
12 Driver BSR CDE0 CDE1 CDE2 CRE 1-8 H H L L X 9 L H H H H INPUT,DE/RE PZH PHZ OUTPUT, OD OUTPUT, OD PZL PLZ OD(H) OD(L) a 3 S1 o PD a 0 S1 o PU NOTES: 1. ll inpu pulses are supplied by a generaor having he following characerisics: r 6 ns, f 6 ns, PRR 1 MHz, duy cycle = 50%, ZO = 50 Ω. 2. ll resisances are in Ω and ±5%, unless oherwise indicaed. 3. ll capaciances are in pf and ±10%, unless oherwise indicaed. 4. ll indicaed volages are ±10 m. FIGURE 11. Driver enable ime waveforms. T 0 or 3 B+ 620 OUTPUT INPUT DE/RE SEE NOTE 1 3 or 0 B- 40 pf SEE NOTE 2 NOTES: 1. CDE0 is high, CDE1, CDE2, BSR, and CRE are low, all ohers are open. 2. Includes probe and jig capaciance. FIGURE 12. Receiver enable and disable ime es circui. DL LND ND MRITIME RE B PGE 12
13 INPUT PLZ PZL OUTPUT 1.4 B+a0 B-a3 T = CC OD INDETERMINTE OUTPUT PHZ PZH 1.4 B+a0 B-a3 T =0 OD INDETERMINTE NOTES: 1. ll inpu pulses are supplied by a generaor having he following characerisics: r 6 ns, f 6 ns, PRR 1 MHz, duy cycle = 50%, ZO = 50 Ω. 2. ll resisances are in Ω and ±5%, unless oherwise indicaed. 3. ll capaciances are in pf and ±10%, unless oherwise indicaed. 4. ll indicaed volages are ±10 m. FIGURE 13. Receiver enable and disable ime waveforms. DL LND ND MRITIME RE B PGE 13
14 4. ERIFICTION 4.1 Produc assurance requiremens. The manufacurer is responsible for performing all inspecion and es requiremens as indicaed in heir inernal documenaion. Such procedures should include proper handling of elecrosaic sensiive devices, classificaion, packaging, and labeling of moisure sensiive devices, as applicable. 5. PREPRTION FOR DELIERY 5.1 Packaging. Preservaion, packaging, labeling, and marking shall be in accordance wih he manufacurer s sandard commercial pracices for elecrosaic discharge sensiive devices. 6. NOTES 6.1 ESDS. Devices are elecrosaic discharge sensiive and are classified as ESDS class 1 minimum. 6.2 Configuraion conrol. The daa conained herein is based on he salien characerisics of he device manufacurer s daa book. The device manufacurer reserves he righ o make changes wihou noice. This drawing will be modified as changes are provided. 6.3 Suggesed source(s) of supply. Idenificaion of he suggesed source(s) of supply herein is no o be consrued as a guaranee of presen or coninued availabiliy as a source of supply for he iem. DL Land and Mariime mainains an online daabase of all curren sources of supply a hp:// endor iem drawing adminisraive conrol number 1/ Device manufacurer CGE code endor par number Top side marking -01XE SN65HD09IDGGREP SN65HD09EP 1/ The vendor iem drawing esablishes an adminisraive conrol number for idenifying he iem on he engineering documenaion. CGE code Source of supply Texas Insrumens, Inc. Semiconducor Group 8505 Fores Lane P.O. Box Dallas, TX Poin of conac: U.S. Highway 75 Souh P.O. Box 84, M/S 853 Sherman, TX DL LND ND MRITIME RE B PGE 14
TITLE MICROCIRCUIT, LINEAR, 1-Mbps QUAD DIGITAL ISOLATORS, MONOLITHIC SILICON REVISIONS LTR DESCRIPTION DATE APPROVED REV PAGE REV PAGE REV
REISIONS LTR DESCRIPTION DTE PPROED Prepared in accordance wih SME Y14.24 endor iem drawing RE PGE RE PGE RE STTUS OF PGES RE PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PMIC N/ PREPRED BY Phu H. Nguyen
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, QUADRUPLE 2-INPUT EXCLUSIVE-OR GATE, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate to current MIL-PRF-38535 requirements. - PHN 13-12-11 Thomas M. Hess CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990
More informationTITLE MICROCIRCUIT, DIGITAL, ADVANCED CMOS, 16- BIT BUS TRANSCEIVER WITH THREE-STATE OUTPUTS, TTL COMPATIBLE, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED B Update boilerplate paragraphs to current requirements. - PHN Update boilerplate to current MIL-PRF-38535 requirements. - PHN 09-02-04 Charles F. Saffle 15-07-28
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, 3.3 V CAN TRANSCEIVERS, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate to current MIL-PRF-38535 requirements. - PHN 14-01-09 Thomas M. Hess CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990
More informationTITLE MICROCIRCUIT, DIGITAL, 200 MHz GENERAL PURPOSE CLOCK BUFFER, PCI-X COMPLIANT, MONOLITHIC SILICON REVISIONS LTR DESCRIPTION DATE APPROVED
REISIONS LTR DESCRIPTION DTE PPROED dd top side marking in section 6.3.-phn 13-03-21 Thomas M. Hess B Correct part number in section 6.3. - phn 14-05-05 Thomas M. Hess Prepared in accordance with SME Y14.24
More informationLTR DESCRIPTION DATE (YY-MM-DD) APPROVED. Update boilerplate paragraphs to current requirements. - PHN
REVISIONS LTR DESCRIPTION DTE (YY-MM-DD) PPROVED B Update boilerplate paragraphs to current requirements. - PHN Update boilerplate to current MIL-PRF-38535 requirements. - PHN 10-01-19 Thomas M. Hess 15-11-24
More informationTITLE MICROCIRCUIT, DIGITAL, ADVANCED CMOS, 16- BIT D-TYPE EDGE-TRIGGERED FLIP-FLOP WITH 3-STATE OUTPUTS, TTL COMPATIBLE, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED B Update boilerplate paragraphs to current requirements. - PHN Update boilerplate to current MIL-PRF-38535 requirements. - PHN 09-02-17 Charles F. Saffle 15-07-28
More informationDISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.
REISIONS LTR DESCRIPTION DTE PPROED Update boilerplate to current MIL-PRF-38535 requirements. - PHN 17-11-16 Thomas M. Hess B Correct number of pin in section 1.2.2. - PHN 18-09-05 Thomas M. Hess Prepared
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED B Update boilerplate paragraphs to current requirements. - PHN Update boilerplate to current MIL-PRF-38535 requirements. - PHN 10-06-22 Thomas M. Hess 16-03-21 Thomas
More informationDLA LAND AND MARITIME COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Correct the vendor part number from SN65LVDS31MDTEP to SN65LVDS31MDREP. Make change to the V OC(PP) test by deleting 150 mv maximum and replacing with 50 mv typical..
More informationPI90LV9637. LVDS High-Speed Differential Line Receivers. Features. Description. Applications PI90LV9637
LVDS High-Speed Differenial Line Receivers Feaures Signaling Raes >400Mbps (200 MHz) Single 3.3V Power Supply Design Acceps ±350mV (ypical) Differenial Swing Maximum Differenial Skew of 0.35ns Maximum
More informationREVISIONS LTR DESCRIPTION DATE APPROVED Thomas M. Hess. Update boilerplate to current MIL-PRF requirements. - PHN
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate to current MIL-PRF-38535 requirements. - PHN 14-06-24 Thomas M. Hess CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990
More informationPI90LV022, PI90LVB022
PI9LV, PI9LVB 456789456789456789456789456789456789456789456789456789456789456789456789456789 LVDS Mux/Repeaer Feaures Mees or Exceeds he Requiremens of ANSI TIA/ EIA-644-995 Designed for Signaling Raes
More informationDISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate paragraphs to current requirements. - PHN 09-06-24 Thomas M. Hess B Correct dimensions E and E1, case Y in Figure 1. Update boilerplate paragraphs
More informationCorrect the maximum operating temperature range in section 1.1, 1.3 and phn. Update boilerplate to current MIL-PRF requirements.
REVISIONS LTR DESCRIPTION DTE PPROVED B Correct the maximum operating temperature range in section 1.1, 1.3 and 1.4. - phn Update boilerplate to current MIL-PRF-38535 requirements. - PHN 09-08-18 Thomas
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate paragraphs to current requirements. - PHN 09-11-09 Thomas M. Hess Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Change the topside marking from M3232C to MB3232M as specified under paragraph 6.3. Make change to note 2 and add note to case outline Y as specified under figure
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, HIGH SPEED ISOLATORS, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Make change to note 2 as specified under paragraph 6.3. Update document paragraphs to current requirements. - ro 15-05-14 C. SFFLE CURRENT DESIGN CTIVITY CGE CODE
More informationPI90LV022, PI90LVB022
LVDS Mux/Repeaer Feaures Mees or Exceeds he Requiremens of ANSI TIA/ EIA-644-995 Designed for Signaling Raes up o 65 Mbi/s (5 MHz) Operaes from a.v Supply: 4 C o +85 C Low Volage Differenial Signaling
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, CONTROLLER AREA NETWORK (CAN) TRANSCEIVER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DTE PPROVED dd JEDEC references under section 2. Update document paragraphs to current requirements. - ro 15-10-20 C. SFFLE CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO:
More informationTITLE MICROCIRCUIT, DIGITAL, 16 BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate to current MIL-PRF-38535 requirements. - PHN 18-05-22 Thomas M. Hess Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE
More informationTITLE MICROCIRCUIT, LINEAR, V AUX POWER DISTRIBUTION SWITCH, MONOLITHIC SILICON REVISIONS LTR DESCRIPTION DATE APPROVED REV PAGE REV PAGE REV
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 PMIC N/ PREPRED BY Phu H. Nguyen DL LND ND
More informationREVISIONS LTR DESCRIPTION DATE APPROVED Thomas M. Hess. Update boilerplate paragraphs to current requirements. - PHN
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate paragraphs to current requirements. - PHN 11-11-29 Thomas M. Hess B dd device type 03. - phn 12-02-27 Thomas M. Hess CURRENT DESIGN CTIVITY CGE
More informationDLA LAND AND MARITIME COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, CMOS, ±% V/ +5V, 4 Ω, SINGLE SPDT SWITCH, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/ PREPRED BY Phu H. Nguyen DL
More informationPI90LV032A PI90LV028A PI90LV018A. 3V LVDS High-Speed Differential Line Receivers PI90LV032A. Features Signaling Rates >400Mbps (200 MHz) PI90LV028A
PI90LV032A PI90LV02A PI90LV0A 3V LVDS HighSpeed Differenial Line Receivers Feaures Signaling Raes >400Mbps (200 MHz) PI90LV032A Single 3.3V Power Supply Design Acceps ±350mV (ypical) Differenial Swing
More informationCorrect lead finish for device 01 on last page. - CFS
REVISIONS LTR DESCRIPTION DTE PPROVED B Correct lead finish for device 01 on last page. - CFS Update paragraph 6.3, device -02X is no longer available. Update paragraphs to current requirements. - ro 05-12-02
More informationDLA LAND AND MARITIME COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE 18 19 20 21 22 23 24 25 REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
More informationTITLE MICROCIRCUIT, DIGITAL, MICROPROCESSOR VOLTAGE MONITORS WITH PROGRAMMABLE VOLTAGE DETECTION, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 PMIC N/ PREPRED BY Phu H. Nguyen DL LND ND
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, LINEAR, PRECISION PROGRAMMABLE REFERENCE, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED B dd device type 02. Update boilerplate to current revision. - CFS Update boilerplate paragraphs to current requirements. - PHN 06-07-06 Thomas M. Hess 13-09-12 Thomas
More informationDATA SHEET. 1N914; 1N916 High-speed diodes DISCRETE SEMICONDUCTORS Sep 03
DISCRETE SEMICONDUCTORS DATA SHEET M3D176 Supersedes daa of April 1996 File under Discree Semiconducors, SC01 1996 Sep 03 FEATURES Hermeically sealed leaded glass SOD27 (DO-35) package High swiching speed:
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED dd device type 09. - phn 08-03-24 Thomas M. Hess B C Update boilerplate to current MIL-PRF-38535 requirements. - PHN Correct terminal connections, pin 4 and pin 5
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, CMOS, GENERAL PURPOSE LINK LAYER CONTROLLER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DTE PPROVED B Update boilerplate paragraphs to current requirements. - CFS Update boilerplate paragraphs to current requirements. - PHN 08-02-25 Thomas M. Hess 13-10-28 Thomas
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, LINEAR, 17 V, 1.5 A SYNCHRONOUS STEP-DOWN CONVERTER, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED dd device type 02. - PHN 07-11-06 Thomas M. Hess B dd device type 03. - PHN 07-11-27 Thomas M. Hess C dd test conditions to the P-channel MOSFET current limit test
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Correct terminal connections in figure 2. - phn 07-06-25 Thomas M. Hess B Update boilerplate to current MIL-PRF-38535 requirements. - PHN 14-03-20 Thomas M. Hess CURRENT
More informationDISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.
REVISIONS TR DESCRIPTION DTE PPROVED Update boilerplate to current MIPRF38535 requirements. PN 170417 Thomas M. ess CURRENT DESIGN CTIVITY CGE CODE S CNGED NMES TO: D ND ND MRITIME COUMBUS, OIO 432183990
More informationV62/03634 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE
REVISIONS LTR DESCRIPTION DTE PPROVED dd new device type 09. Update boilerplate to current requirements. Corrections throughout. - CFS 06-12-11 Thomas M. Hess B Update boilerplate paragraphs to current
More informationMX6895BETR. -550V Full Bridge Gate Driver INTEGRATED CIRCUITS DIVISION. Features. Description. Applications. Ordering Information
-550V Full Bridge Gae Driver INTEGRATED CIRCUITS DIVISION Feaures Full Bridge Gae Driver Inernal High Volage Level Shif Funcion Negaive 550V Lamp Supply Volage 3V o 12V CMOS Logic Compaible 8V o 12V Inpu
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL-LINEAR, 1 OHM, SPDT ANALOG SWITCH, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Update document paragraphs to current requirements. - ro 14-06-25 C. SFFLE CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990 Prepared
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate paragraphs to current requirements. - PHN 10-01-19 Thomas M. Hess Prepared in accordance with SME Y14.24 REV PGE REV PGE Vendor item drawing REV
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate to current MIL-PRF-38535 requirements. - PHN 17-01-24 Thomas M. Hess CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, DIGITAL TRANSMITTER, MONOLITHIC SILICON REVISIONS
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate to current MIL-PRF-38535 requirements. - PHN 14-03-20 Thomas M. Hess CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990
More informationDisribued by: www.jameco.com 1-800-831-4242 The conen and copyrighs of he aached maerial are he propery of is owner. 16K-Bi CMOS PARALLEL E 2 PROM FEATURES Fas Read Access Times: 200 ns Low Power CMOS
More informationDISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.
REVISIONS LTR DESCRIPTION DTE PPROVED dd terminal symbol description information under figure 2. Mode of transportation and quantity column under paragraph 6.3. Update document paragraphs to current requirements.
More informationDLA LAND AND MARITIME COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Table I, input offset voltage test, delete 9 mv and substitute 8 mv. Table I, input offset current test, delete 20 n and substitute 2 n. Table I, input bias current
More informationHI-8585, HI ARINC 429 Line Driver PIN CONFIGURATION DESCRIPTION SUPPLY VOLTAGES FUNCTION TABLE FEATURES PIN DESCRIPTION TABLE
February DESCRIPTION The HI-8585 and HI-858 are CMOS inegraed circuis designed o direcly drive he ARINC 49 bus in an 8-pin package. Two logic inpus conrol a differenial volage beween he oupu pins producing
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE
REVISIONS TR DESCRIPTION DTE PPROVED B Update boilerplate paragraphs to current requirements. - PN Update boilerplate to current MI-PRF-38535 requirements. - PN 11-08-22 Thomas M. ess 16-09-20 Thomas M.
More informationfunctional operation of the device at these or any other condition beyond those indicated in the specifications is not implied.
H037N06L Feaures Low On-Resisance Fas Swiching 100% Avalanche Tesed Repeiive Avalanche Allowed up o Tjmax Lead-Free, RoHS omplian Descripion H037N06L designed by he rench processing echniques o achieve
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED B dd device type 02. Update boilerplate to current revision. - CFS Update boilerplate to current MIL-PRF-38535 requirements. - PHN 06-12-15 Thomas M. Hess 14-01-27
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED dd reference information to section 2. Make change to notes specified under figure 1. Update boilerplate paragraphs to current requirements. - ro 11-12-01 C. SFFLE
More informationAnalog Multiplexer Demultiplexer High-Performance Silicon-Gate CMOS
TECHNICAL DATA IW0B Analog Muliplexer Demuliplexer HighPerformance SiliconGae CMOS The IW0B analog muliplexer/demuliplexer is digially conrolled analog swiches having low ON impedance and very low OFF
More informationDLA LAND AND MARITIME COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PMIC N/ PREPRED BY RICK
More informationAnalog Multiplexer Demultiplexer High-Performance Silicon-Gate CMOS
TEHNIAL DATA Analog Muliplexer Demuliplexer HighPerformance SiliconGae MOS IW402B N SUFFIX PLASTI The IW402B analog muliplexer/demuliplexer is digially conrolled analog swiches having low ON impedance
More informationDLA LAND AND MARITIME COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/ PREPRED BY RICK OFFICER
More informationORDER INFORMATION TO pin 320 ~ 340mV AMC7150DLF
www.addmek.com DESCRIPTI is a PWM power ED driver IC. The driving curren from few milliamps up o 1.5A. I allows high brighness power ED operaing a high efficiency from 4Vdc o 40Vdc. Up o 200KHz exernal
More informationDEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, CMOS, THREE-PORT CABLE TRANSCEIVER/ARBITER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DTE PPROVED dd device type -02 as a substitute for device type -01. Obsolete device type -01. Correct vendor datasheet errors for limits of V DD, V OD, I OZ parameters. Update
More informationDLA LAND AND MARITIME COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE 18 19 20 21 22 REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PMIC
More informationDLA LAND AND MARITIME COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PMIC N/ PREPRED BY RICK
More informationTITLE MICROCIRCUIT, DIGITAL, PHASE DETECTOR/ FREQUENCY SYNTHESIZER, MONOLITHIC SILICON REVISIONS LTR DESCRIPTION DATE APPROVED
REVISIONS LTR DESCRIPTION DTE PPROVED dd lead finish E to the devices. - PHN 18-02-15 Thomas M. Hess Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE
More informationTITLE MICROCIRCUIT, LINEAR, 16-BIT, ISOLATED SIGMA-DELTA MODULATOR, MONOLITHIC SILICON REVISIONS LTR DESCRIPTION DATE APPROVED REV PAGE REV PAGE REV
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 PMIC N/ PREPRED BY Phu H. Nguyen DL LND ND
More informationStresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only;and
80/110A N-hannel Advanced Power MOSFET Feaures Low On-esisance Fas Swiching 100% Avalanche Tesed epeiive Avalanche Allowed up o Tjmax Lead-Free, ohs omplian Descripion S80110AT designed by he rench processing
More informationPRELIMINARY N-CHANNEL MOSFET 1 P-CHANNEL MOSFET. Top View
HEXFET Power MOSFET dvanced Process Technology Ulra Low On-Resisance ual N and P Channel Mosfe Surface Moun vailable in Tape & Reel ynamic dv/d Raing Fas Swiching escripion PRELIMINRY N-CHNNEL MOSFET 8
More informationDLA LAND AND MARITIME COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Update document paragraph to current requirements. - ro 17-11-15 Charles F. Saffle Prepared in accordance with SME Y14.24 REV PGE REV PGE Vendor item drawing REV STTUS
More informationA Add footnote to paragraphs and 6.3. Make changes to figure 1 and the dimensions table. - ro
REVISIONS LTR DESCRIPTION DTE PPROVED dd footnote to paragraphs 1.2.2 and 6.3. Make changes to figure 1 and the dimensions table. - ro 12-01-12 C. SFFLE B Update document paragraphs to current requirements.
More informationAdd device type 02. Update boilerplate to current revision. - CFS
REVISIONS LTR DESCRIPTION DTE PPROVED B C dd device type 02. Update boilerplate to current revision. - CFS Correct circuit function descriptions in paragraph 1.2.1 to accurately describe devices. - CFS
More informationV62/03626 REVISIONS LTR DESCRIPTION DATE APPROVED REV PAGE REV PAGE REV REV STATUS OF PAGES PAGE
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE 18 19 20 REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PMIC N/ Original
More informationStresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only;and
Feaures Low On-esisance Fas Swiching 100% Avalanche Tesed epeiive Avalanche Allowed up o Tjmax Lead-Free, ohs omplian Descripion H037N06L0650P designed by he rench processing echniques o achieve exremely
More informationThree phase full Bridge with Trench MOSFETs in DCB isolated high current package
MTI2WX75GD Three phase full Bridge wih Trench MOSFETs in DCB isolaed high curren package S = 75 V 25 = 255 R DSon yp. = 1.1 mw Par number MTI2WX75GD G1 L1+ L2+ T1 T3 T5 G3 G5 L3+ Surface Moun Device S1
More informationTITLE MICROCIRCUIT, LINEAR, DC MOTOR DRIVER IC, MONOLITHIC SILICON REVISIONS LTR DESCRIPTION DATE APPROVED REV PAGE REV PAGE REV REV STATUS OF PAGES
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/ PREPRED BY Phu H. Nguyen
More informationDISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/ PREPRED BY Phu H. Nguyen DL LND
More informationTITLE MICROCIRCUIT, LINEAR, LC 2 MOS, QUAD SPST SWITCHES, MONOLITHIC SILICON REVISIONS LTR DESCRIPTION DATE APPROVED REV PAGE REV PAGE REV
REIION LTR ECRIPTION TE PPROE Prepared in accordance with ME Y14.24 endor item drawing RE PGE RE PGE RE TTU OF PGE RE PGE 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/ PREPRE BY Phu H. Nguyen L LN N MRITIME 43218-3990
More informationREVISIONS LTR DESCRIPTION DATE APPROVED. Update boilerplate to current MIL-PRF requirements. - PHN Thomas M. Hess
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate to current MIL-PRF-38535 requirements. - PHN 14-08-25 Thomas M. Hess CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990
More informationIR Receiver Module for Light Barrier Systems
New Produc IR Receiver Module for Ligh Barrier Sysems TSSP5838 1926 FEATURES Low supply curren Phoo deecor and preamplifier in one package Inernal filer for 38 khz IR signals Shielding agains EMI Supply
More informationPROFET BTS 736 L2. Smart High-Side Power Switch Two Channels: 2 x 40mΩ Status Feedback
PROFET BTS 736 2 Smar igh-side Power Swich Two Channels: 2 x 40mΩ Saus Feedback Produc Summary Package Operaing olage bb(on) 4.75...41 Acive channels one wo parallel On-sae Resisance R ON 40mΩ 20mΩ Nominal
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO TITLE MICROCIRCUIT, LINEAR, SWITCH MODE LEAD ACID BATTERY CHARGER, MONOLITHIC SILICON
REVISIONS LTR DESCRIPTION DTE PPROVED dd the minimum limit to the High output voltage (V OH ) test as specified under Table I. Updating document paragraph to current requirements. - ro 16-05-24 C. SFFLE
More informationDLA LAND AND MARITIME COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/ PREPRED BY RICK OFFICER DL
More informationSolid-state Timer H3CT
Solid-sae Timer H3CT DIN 48 x 48-mm Sandard Size Analog Timer Wide ime range (for 4 series of models); 0.1 s o 30 hrs. Wih H3CT-8H models, he oupu ype can be swiched beween ime limi DPDT and ime limi SPDT
More informationThree phase full Bridge with Trench MOSFETs in DCB-isolated high-current package
MTI145WX1GD Three phase full Bridge wih Trench MOSFETs in DCB-isolaed high-curren package S = 1 V 5 = 19 R DSon yp. = 1.7 mw Par number MTI145WX1GD L1+ L+ L3+ G1 G3 G5 Surface Moun Device S1 S3 S5 L1 L
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED B Update boilerplate paragraphs to current requirements. - PHN dd a note to figure 1 terminal connections. Update document paragraphs to current requirements. - ro
More informationPrimary Side Control SMPS with Integrated MOSFET
General Descripion GG64 is a primary side conrol SMPS wih an inegraed MOSFET. I feaures programmable cable drop compensaion and a peak curren compensaion funcion, PFM echnology, and a CV/CC conrol loop
More informationIR Receiver Module for Light Barrier Systems
IR Receiver Module for Ligh Barrier Sysems DESIGN SUPPORT TOOLS 19026 click logo o ge sared FEATURES Up o 2 m for presence sensing Uses modulaed burss a 38 khz 940 nm peak wavelengh PIN diode and sensor
More information1N Amp SCHOTTKY RECTIFIER. Bulletin PD rev. C 11/02. Description/ Features. Major Ratings and Characteristics
SCHOTTKY ECTIFIE 60 Amp Major aings and Characerisics Descripion/ Feaures TO-203AB (DO-5) Characerisics Unis I F(AV) ecangular 60* A waveform V WM 45* V I FSM @ 60Hz 000* A V F @ 60 Apk, T = 25 C 0.68*
More informationPhoto Modules for PCM Remote Control Systems
Phoo Modules for PCM Remoe Conrol Sysems TFMS 5..0 Available ypes for differen carrier frequencies Type f 0 Type f 0 TFMS 5300 30 khz TFMS 5330 33 khz TFMS 5360 36 khz TFMS 5370 36.7 khz TFMS 5380 38 khz
More informationIR Receiver Module for Light Barrier Systems
IR Receiver Module for Ligh Barrier Sysems TSSP4..SSXB Vishay Semiconducors DESIGN SUPPORT TOOLS Models Available 3 MECHANICAL DATA Pinning: = OUT, = GND, 3 = V S 7 click logo o ge sared DESCRIPTION The
More informationDISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate to current MIL-PRF-38535 requirements. - PHN 17-11-16 Thomas M. Hess CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990
More informationIR Receiver Modules for Remote Control Systems
IR Receiver Modules for New TSOP48.. 2 3 MECHANICAL DATA Pinning = OUT, 2 =, 3 = 6672 FEATURES Low supply curren Phoo deecor and preamplifier in one package Inernal filer for PCM frequency Improved shielding
More informationAK8777B. Overview. Features
AK8777B Hall Effec IC for Pulse Encoders Overview The AK8777B is a Hall effec lach which deecs boh verical and horizonal (perpendicular and parallel o he marking side of he package) magneic field a he
More informationDISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.
REVISIONS LTR DESCRIPTION DTE PPROVED Update document paragraphs to current requirements. - ro 18-05-08 C. SFFLE Prepared in accordance with SME Y14.24 REV PGE REV PGE Vendor item drawing REV STTUS OF
More informationIR Sensor Module for Reflective Sensor, Light Barrier, and Fast Proximity Applications
IR Sensor Module for Reflecive Sensor, Ligh Barrier, and Fas Proximiy Applicaions 2 3 DESIGN SUPPORT TOOLS Models Available MECHANICAL DATA Pinning: = OUT, 2 = GND, 3 = V S click logo o ge sared 6672 APPLICATIONS
More informationDEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO
REVISIONS LTR DESCRIPTION DTE PPROVED Update boilerplate paragraphs to current requirements. - ro 12-10-23 C. SFFLE CURRENT DESIGN CTIVITY CGE CODE HS CHNGED NMES TO: DL LND ND MRITIME 43218-3990 Prepared
More informationDiode RapidSwitchingEmitterControlledDiode. IDP20C65D2 EmitterControlledDiodeRapid2CommonCathodeSeries. Datasheet. IndustrialPowerControl
Diode RapidSwichingEmierConrolledDiode IDP20C65D2 EmierConrolledDiodeRapid2CommonCahodeSeries Daashee IndusrialPowerConrol EmierConrolledDiodeRapid2CommonCahodeSeries RapidSwichingEmierConrolledDiode Feaures:
More information90SQ... SERIES. 9 Amp SCHOTTKY RECTIFIER. Bulletin PD rev. E 06/05. Description/ Features. Major Ratings and Characteristics
90SQ... SEIES SCHOTTKY ECTIFIE 9 Amp Major aings and Characerisics Characerisics 90SQ... Unis I F(A) ecangular 9 A waveform M range 30 / 4 I FSM @ p = µs sine 20 A F @ 9 Apk, T = 2 C 0.42 range - o 0 C
More informationDiode RapidSwitchingEmitterControlledDiode. IDV30E65D2 EmitterControlledDiode. Datasheet. IndustrialPowerControl
Diode RapidSwichingEmierConrolledDiode EmierConrolledDiode Daashee IndusrialPowerConrol EmierConrolledDiode RapidSwichingEmierConrolledDiode Feaures: QualifiedaccordingoJEDECforargeapplicaions 6VEmierConrolledechnology
More informationULTRA-LOW VOLTAGE PROCESSOR SUPERVISORY CIRCUITS
www.i.com TPS-xx TPS4-xx, TPS5-xx TPS6-xx, TPS8-xx SLVS7B AUGUST 999 REVISED FEBRUARY 4 ULTRA-LOW VOLTAGE PROCESSOR SUPERVISORY CIRCUITS FEATURES Minimum Supply Volage of.75 V Supply Volage Supervision
More informationIR Sensor Module for Reflective Sensor, Light Barrier, and Fast Proximity Applications
IR Sensor Module for Reflecive Sensor, Ligh Barrier, and Fas Proximiy Applicaions 2 3 DESIGN SUPPORT TOOLS 6672 click logo o ge sared FEATURES Up o 2 m for presence and proximiy sensing Uses modulaed burss
More informationHRF32. Silicon Schottky Barrier Diode for Rectifying. ADE D(Z) Rev 4 Jul Features. Ordering Information. Outline
Silicon Schoky Barrier Diode for Recifying ADE-28-164D(Z) Rev 4 Jul. 1997 Feaures Good for high-frequency recify. LRP srucure ensures higher reliabiliy. Ordering Informaion Type No. Laser Mark Package
More informationSmart High-Side Power Switch Two Channels: 2 x 30mΩ Current Sense
POFET Smar High-Side Power Swich Two Channels: 2 x 3mΩ Curren Sense Produc Summary Package Operaing olage (on) 5...34 Acive channels one wo parallel On-sae esisance ON 3mΩ 15mΩ Nominal load curren (NOM)
More informationDiode FastSwitchingEmitterControlledDiode. IDW50E60 EmitterControlledDiodeseries. Datasheet. IndustrialPowerControl
Diode FasSwichingEmierConrolledDiode IDW5E6 EmierConrolledDiodeseries Daashee IndusrialPowerConrol IDW5E6 EmierConrolledDiodeseries FasSwichingEmierConrolledDiode Feaures: QualifiedaccordingoJEDECforargeapplicaions
More informationIR Receiver Modules for Remote Control Systems
2 3 MECHANICAL DATA Pinning: = OUT, 2 =, 3 = V S 6672 FEATURES Very low supply curren Phoo deecor and preamplifier in one package Inernal filer for PCM frequency Improved shielding agains EMI Supply volage:
More informationDISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited.
REVISIONS LTR DESCRIPTION DTE PPROVED dd Mode of transportation and quantity column under paragraph 6.3. Update document paragraphs to current requirements. - ro 18-06-04 C. SFFLE Prepared in accordance
More information<IGBT Modules> CM400DY-13T HIGH POWER SWITCHING USE INSULATED TYPE
dual swich (half-bridge) APPLICATION AC Moor Conrol, Moion/Servo Conrol, Power supply, ec. OPTION (Below opions are available.) PC-TIM (Phase Change Thermal Inerface Maerial) pre-apply VCEsa selecion for
More information