Electrical Specifications Frequency Isolation. Power. Degrees Avg. CW Watts ºC. 90 ± to +95 TOP VIEW SIDE VIEW BOTTOM VIEW.

Transcription

1 Description The is a low profile, high performance 3dB hybrid coupler in a new easy to use, manufacturing friendly surface mount package. It is designed for CMMB band applications. The is designed particularly for balanced power and low noise amplifiers, plus signal distribution and other applications where low insertion loss and tight amplitude and phase balance is required. It can be used in high power applications up to 200 Watts. arts have been subjected to rigorous qualification testing and they are manufactured using materials with coefficients of thermal expansion (CTE) compatible with common substrates such as FR4, G-10, RF-35, RO4350 and polyimide. Orientation Marker art No. Signal ad GND Features: MHz CMMB High ower Very Low Loss Tight Amplitude Balance High Isolation Low VSWR Good Repeatability CTE compatible with FR4, G-10, RF-35, RO4350B and polyimide Immersion gold, prevent surface oxidation & scratch RoHS Compliant Tape & Reel ackage available Mechanical Outline Electrical Specifications Frequency Isolation Insertion Amplitude VSWR Loss Balance MHz db Min db Max Max : 1 db Max ± 0.40 hase Balance ower Operating Temp. Degrees Avg. CW Watts ºC 90 ± to +95 Notes: 1. All the above data are based on specified demo board. 2. Insertion loss:thru board loss has been removed. TO VIEW SIDE VIEW BOTTOM VIEW in 1 in 2 in 2 in 1 YANTEL XXXX in 4 in 3 in 3 in 4

2 Hybrid Coupler in Configuration The has an orientation marker to denote in 1. Once port one has been identified the other ports are known automatically. lease see the chart below for clarification: Configuration in 1 in 2 in 3 in 4 Splitter Input Isolated -3dB Ð dB Ð Splitter Isolated Input -3dB Ð -3dB Ð - 90 Splitter -3dB Ð dB Ð Input Isolated Splitter -3dB Ð -3dB Ð - 90 Isolated Input *Combiner AÐ - 90 AÐ Isolated Output *Combiner A Ð AÐ - 90 Output Isolated *Combiner Isolated Output AÐ - 90 AÐ *Combiner Output Isolated A Ð AÐ - 90 *Note: A is the amplitude of the applied signals. When two quadrature signals with equal amplitudes are applied to the coupler as described in the table, they will combine at the output port. If the amplitudes are not equal, some of the applied energy will be directed to the isolated port. Typical erformance Data (@) Frequency (MHz) Coupling Transmission Insertion Loss Isolation Amplitude Balance hase (degree) Return Loss S11 S22 S33 S

3 Typical erformance (-55 C, 25 C, 95 C: MHz) Return Loss (ort 1) Return Loss (ort 2) Return Loss (ort 3) Return Loss (ort 4)

4 Typical erformance (-55 C, 25 C, 95 C: MHz) Coupling & Transmission (ort 1 feeding) Coupling Transmission Insertion Loss(ort 1 feeding) hase (ort 1 feeding) Isolation (ort 1 feeding)

5 Definition of Measured Specifications arameter Definition Mathematical Representation Vmax The impedance match of VSWR = VSWR the coupler to a 50W Vmin (Voltage Standing Wave system. A VSWR of 1:1 is Vmax = voltage maxima of a standing wave Ratio) optimal. Vmin = voltage minima of a standing wave Return Loss Insertion Loss Isolation hase Balance Amplitude Balance The impedance match of the coupler to a 50W system. Return Loss is an alternate means to express VSWR. The input power divided by the sum of the power at the two output ports. The input power divided by the power at the isolated port. The difference in phase angle between the two output ports. The power at each output divided by the average power of the two outputs. Return Loss = 20log Insertion Loss= 10log Isolation= 10log cpl transmission ( ) VSWR+1 VSWR -1 in cpl + in iso transmission hase at coupled port hase at transmisson port 10log cpl + 2 and 10log + 2 transmission cpl transmission ( ) Test Method 1. Calibrating your vector network analyzer. 2. Connect the VNA 4 ort to DUT respectively. 3. Measure the data of coupling through port 1 to port 4(S41). 4. Measure the data of transmission through port 1 to port 3(S31). 5. Measure the data of isolation through port 1 to port 2(S21). 6. Measure the data of phase port 4 & port 3(port 1 feeding). 7. Measure the data of return loss port 1, port 2, port 3 & port According to the above data to calculate insertion loss, amplitude balance & phase. Vector Network Analyzer ort 1 ort 2 ort 3 ort 4 Note: 1. When calculating insertion loss at room temperature, demo board loss should be removed from both coupling & transmission data. lease refer to the below table for demo board loss : Frequency Range(MHz) Demo Board DUT

6 Recommended CB Layout NOTE: 1. 50Ω line width is shown above designing from RO4350B dieletric thickness 0.762mm; copper 1 OZ 2. Bottom side of the CB is continuous ground plane. 3. All dimensions shown in mm. Reflow rofile eak temperature melting point alloy Reflow Zone 50-90sec reheat/soak 60-80sec Soaking Zone 60-90sec cooldown Time(s)

7 Reliability Test Flow Reliability Test Mechanical/Visual Inspection Electrical Testing at room temperature S-parameter Mount parts to test boards Visual Inspection Control Units n=5 Visual Inspection Resistance to Solder per Mil202F.210E.Condition K heat n=20 Mount boards to Al blocks Visual Inspection Electrical Testing at room temperature and over temperature S-parameter(,,,150,200 ) Electrical Testing at room temperature S-parameter Control Units n=5 Visual Inspection M e c ha n i c a l / vi s ua l Inspection Control Units n=5 Voltage Breakdown Test per Mil202F-301,1KV n=40 Electrical Testing at room temperature S-parameter Control Units n=10 Thermal Cycle 75 cycles,- to1,5 /min 15 min dwell n=40

8 Reliability Test Flow Electrical Testing at room temperature S-parameter Control Units n=10 Moisture Resistance Testing - to 65 for 2hrs.@90% humidity.increase to 95% humidity and soak for 4hrs.ramp temp to in 2hrs,repeat for 10 cycles and then soak -10 for 3hrs n=40 Electrical Testing at room temperature S-parameter Control Units n=10 Bake parts for 1 hr at 100 n=40 Electrical Testing at room temperature S-parameter High ower Test n=2 Life Testing Rated power input 100 base plate temperature 96 hrs 3 in series n=6 Visual Inspection Mechanical Inspection Electrical Testing at room temperature S-parameter n=6 Microsection 3 Test units and 1 control Microsection 2 life,1 high power and 1 control

9 Tape and Reel Drawing Feeding Direction DIM ITEM (mm) (inch) TOLE (mm) D D1 2 6 SECTIONA-A W T K0 SECTIONB-B W A0 B0 K0 F E D D1 0 2 T 7" /R 500pcs Notice: A.10 Sprocket hole pitch cumulative tolerance is 0.2mm. B. Carrier camber shall be not more than 1mm per 100mm through a length of 250mm. C. All dimensions meet EIA-418-B requirements. D. A0 & B0 measured as indicated. E. K0 measured from a place on the inside bottom of the pocket to top surface of carrier. F. Material: E 100 G. Thickness: 0.30±0.05mm H. 500 units (maximum) / T&R W E Symbol Dimensions (mm) (inch) F DETAIL2:1 A N T W A N T E F D 24.5± ±0.5 63± ± ± ± /