1995 Metric CSJ SPECIAL SPECIFICATION ITEM Multimode Video Fiber Optic Transmission Equipment

Size: px
Start display at page:

Download "1995 Metric CSJ SPECIAL SPECIFICATION ITEM Multimode Video Fiber Optic Transmission Equipment"

Transcription

1 1995 Metric CSJ SPECIAL SPECIFICATION ITEM 6329 Multimode Video Fiber Optic Transmission Equipment 1.0 Description. This Item shall govern for the furnishing and installation of Video Fiber Optic Transmission Equipment in designated equipment cabinets in the field and in the Satellite Control Center as shown on the plans, as detailed in the Special Specifications and as directed by the Engineer. 2.0 Material. 2.1 General Requirements. All materials furnished, assembled, fabricated or installed under this Item shall be new, corrosion resistant and in strict accordance with the details shown on the plans and in the Specifications. 2.2 Functional Requirements. The video fiber optic transmitterreceiver system shall provide a video link to transmit the baseband video signal from the communications hubs to the Satellite Control Center or to the video multiplexor location. The video fiber optic transmitter shall generate optical signals modulated by the baseband video signal from the video camera output in the form of pulse frequency modulation. The video fiber optic receiver shall detect the optical signal and shall convert it to baseband video signal. The operating optical wavelength shall be 1300 nm. Each fiber optic link shall meet RS-250B short haul video requirements. Both the video fiber optic transmitters and receivers shall be from the same manufacturer. 2.3 Electrical/Optical Requirements Transmitter Video Input. Transmitter Video Input shall be 75 Ohms nominal, 1.4 Volt peak-to-peak between sync tip to 100% white level Transmitting Device. The transmitting device shall be a light-emitting diode (LED) which shall have an MTBF of 100,000 hours at 50ºC ambient Transmitter Optical Output. Output power to 50/125 multimode graded index glass fiber at a wavelength of 1300 nm shall be sufficient to accommodate a link loss budget o f 20 db or more

2 Once design is tested and approved, the optical coupled power value and tolerance will become incorporated as part of this Specification for the purpose of acceptance tests Optical Detector. The optical detector of the receiver shall be an APD diode, a PIN or a device approved by the Engineer Receiver Optical Input. Receiver input shall have a minimum sensitivity of 20 db below the transmitter output level and operate within the parameters of this Specification. Once design is tested and approved, the receiver sensitivity value and tolerance shall be incorporated as a part of this Specification for the purpose of acceptance tests Receiver Automatic Gain Control. The receiver shall have automatic gain control (AGC) circuitry to provide the receiver with the required dynamic range from transmitterreceiver spacing of 1 to 20 db. The above dynamic range requirements may be accomplished with external optical attenuators with the approval of the Engineer Receiver Video Output. Receiver Video Output shall be 75 Ohms nominal, 1.4 Volt peak-to-peak between sync tip and 100% white level Modulation. Modulation shall be pulse frequency modulation Signal to Noise Ratio. The system signal to noise ratio (SNR), measured as peak-to-peak white to blanking, to rms noise (ppwb/rms) in a 10 KHz to 5 MHz bandwidth, shall be better than 67 db Linearity. Linearity shall be better than 1% Tilt. Tilt shall be less than 2% Differential Phase. Differential Phase shall be less than 0.5 degrees at 10% to 90% average picture level (APL) Differential Gain. Differential Gain shall be less than 2% at 10 to 90% average picture level (APL) Frequency Response. Frequency Response shall be plus or minus 0.1 db, 10 Hz to 0.5 MHz; plus or minus 0.2 db, 0.5 MHz to 4.2 MHz Optical Fiber Compatibility. Optical Fiber Compatibility shall be 50/125 micron graded index multimode glass fiber Power Requirements. Transmitters and receivers shall operate from 115 VAC plus or minus 20 VAC and shall not draw more than 5 Watts of power each

3 The equipment operation shall not be affected by transient voltages, surges and sags normally experienced on commercial power lines. It is the Contractor's responsibility to check the local power service to determine if any special design is needed for the equipment. The extra cost, if required, shall be included in the bid of this Item Surge Protection. Surge protectors as specified in the Special Specification Item, "Cabinets" shall be installed in the equipment cabinet for the coaxial cable connection to the video camera Power Service Transients. The equipment shall meet the requirements of Sec , "Transients, Power Service" of the NEMA Standard TS , latest revision Wiring. All wiring shall meet the requirements of the National Electric Code. All wires shall be cut to proper length. Cable slacks shall be provided to facilitate removal and replacement of assemblies, panels, and modules. No wire shall be doubled back to take up slack. Wires shall be neatly laced into cable with nylon lacing or plastic straps. Cables shall be secured with clamps Transient Suppression. All DC relays, solenoids, and holding coils shall have diodes across the coils for transient suppression Power Service Protection The equipment shall contain readily accessible, manually resettable or replaceable circuit protection devices (such as circuit breakers or fuses) for equipment and power source protection Fail Safe Provision. The equipment shall be designed such that the failure of the equipment shall not cause the failure of any other unit of equipment. 2.4 Mechanical Requirements Modular Design. The equipment shall be modular in design such that major portions may be readily replaced in the field. Modules of unlike functions shall be mechanically keyed to prevent insertion into the wrong socket or connector. All modules and assemblies shall be clearly identified with name, model number, serial number, and any other pertinent information required to facilitate equipment maintenance Connectors and Harness. All external connections shall be made by means of connectors. The connectors shall be keyed to preclude improper hookups. All wires to and from the connectors shall be color coded and/or appropriately marked. Video input and output connectors shall be BNC type. Each and every conductive contact surface or pin shall be plated with a minimum of 50 microns of gold

4 Optical input and output connectors shall be the ST type with stainless steel housing and ceramic ferrule. Connecting harness of appropriate length and terminated with matching connectors shall be provided for interconnection with the video cameras, video switcher and the fiber optic network Housing. The receiver and transmitter packages shall be suitable for rack mounting or shelf mounting. Card cages for rack mounting of equipment shall be equipped with a power supply capable of supplying power to a fully loaded card cage. The card cage shall be rack mounted on a standard EIA rack. The card cage and power supply shall be included in the bid Item of the video fiber optic receiver. 2.5 Environmental Design Requirements. The equipment shall meet all its specified requirements during and after subjecting to any combination of the following requirements. - Ambient temperature range of -17 degrees C to 60 degrees C - Relative humidity from 0 % to 95 %. 3.0 Construction Methods. 3.1 General. The equipment design and construction shall utilize the latest available techniques with a minimum number of parts, subassemblies, circuits, cards, and modules to maximize standardization and commonality. The equipment shall be designed for ease of maintenance. All component parts shall be readily accessible for inspection and maintenance. Test points shall be provided for checking essential voltages and waveforms. 3.2 Electronic Components. All electronic components shall comply with Special Specification Item, "Electronic Components". 3.3 Mechanical Components All external screws, nuts, and locking washers shall be stainless steel; no self-tapping screws shall be used unless approved by the Engineer. All parts shall be made of corrosion resistant material, such as plastic, stainless steel, anodized aluminum, or brass. All materials used in construction shall be protected from fungus growth and moisture deterioration. Dissimilar metals shall be separated by an inert dielectric material. 3.4 Testing, Documentation and Warranty Testing of the Video Fiber Optic Transmission Equipment shall be in compliance with Section 2.0 of Special Specification Item, "Testing, Training, Documentation and Warranty"

5 Documentation for the Video Fiber Optic Transmission Equipment shall be in compliance with Section 4.0 of Special Specification Item, "Testing, Training, Documentation and Warranty". Warranty for the Video Fiber Optic Transmission Equipment shall be in compliance with Section 5.0 of Special Specification Item, "Testing, Training, Documentation and Warranty". 4.0 Measurement. This Item will be measured as each unit furnished, installed, made fully operational and tested in accordance with these Special Specifications or as directed by the Engineer. 5.0 Payment. The work performed and materials furnished in accordance with this Item and measured as provided under "Measurement" will be paid for at the unit price bid for "Video Fiber Optic Transmitter" or "Video Fiber Optic Receiver". These prices shall be full compensation for all equipment described under this Item with all cables and connectors; for all documentation and testing; and for furnishing all labor, materials, training and equipment necessary to complete the work

SPECIAL SPECIFICATION 6609 Fiber Optic Color Video and Data Transmission Equipment

SPECIAL SPECIFICATION 6609 Fiber Optic Color Video and Data Transmission Equipment 1995 Metric CSJ's 1047-03-056 & 0008-08-066 SPECIAL SPECIFICATION 6609 Fiber Optic Color Video and Data Transmission Equipment 1. Description. This Item shall govern for the furnishing and installation

More information

SPECIAL SPECIFICATION 1118 Data Fiber Optic Transceiver

SPECIAL SPECIFICATION 1118 Data Fiber Optic Transceiver 2004 Specifications CSJ 0050-09-071, 0027-13-205, 0271-14-228, 0500-03-042, 0050-09-070, 0050-09-069 etc, 0050-08-086, 0050-08-087 & 0500-03-577 SPECIAL SPECIFICATION 1118 Data Fiber Optic Transceiver

More information

SPECIAL SPECIFICATION 1789 Fiber Optic RS-232 Data Modem

SPECIAL SPECIFICATION 1789 Fiber Optic RS-232 Data Modem 1993 Specifications CSJ 2266-02-095 SPECIAL SPECIFICATION 1789 Fiber Optic RS-232 Data Modem 1. Description. This Item shall govern for the furnishing and installation of Fiber Optic RS- 232 Data Modem

More information

SPECIAL SPECIFICATION 6419 Fiber Optic Video Transceiver with Data

SPECIAL SPECIFICATION 6419 Fiber Optic Video Transceiver with Data 2004 Specifications CSJ 0617-01-169 SPECIAL SPECIFICATION 6419 Fiber Optic Video Transceiver with Data 1. Description. This Item shall govern for the furnishing and installation of Video optical transceiver

More information

SPECIAL SPECIFICATION 6734 RS-232 Optical Modem

SPECIAL SPECIFICATION 6734 RS-232 Optical Modem 2004 Specifications CSJ 0924-06-244 SPECIAL SPECIFICATION 6734 RS-232 Optical Modem 1. Description. This Item shall govern for the furnishing and installation of Fiber Optic RS- 232 Data Modem (OTR) in

More information

1995 Metric CSJ SPECIAL SPECIFICATION ITEM Drop/Insert Multiplexor/Demultiplexor

1995 Metric CSJ SPECIAL SPECIFICATION ITEM Drop/Insert Multiplexor/Demultiplexor 1995 Metric CSJ 3256-02-049 1.0 Description SPECIAL SPECIFICATION ITEM 6093 Drop/Insert Multiplexor/Demultiplexor This Item shall govern for the furnishing and installation of intelligent drop/insert multiplexor/demultiplexors

More information

1995 Metric CSJ SPECIAL SPECIFICATION ITEM Add/Drop Multiplexor/Demultiplexor

1995 Metric CSJ SPECIAL SPECIFICATION ITEM Add/Drop Multiplexor/Demultiplexor 1995 Metric CSJ 0113-13-109 SPECIAL SPECIFICATION ITEM 6225 Add/Drop Multiplexor/Demultiplexor 1.0 Description. This Item shall govern for the furnishing and installation of intelligent Add/Drop Multiplexor/Demultiplexor

More information

SPECIAL SPECIFICATION 1533 Drop/Insert Multiplexor/Demultiplexor

SPECIAL SPECIFICATION 1533 Drop/Insert Multiplexor/Demultiplexor 1993 Specifications CSJ 0177-11-131 SPECIAL SPECIFICATION 1533 Drop/Insert Multiplexor/Demultiplexor 1. Description. This Item shall govern for for the furnishing and installation of intelligent drop/insert

More information

1993 Specifications CSJ SPECIAL SPECIFICATION ITEM Drop/Insert Multiplexor/Demultiplexor

1993 Specifications CSJ SPECIAL SPECIFICATION ITEM Drop/Insert Multiplexor/Demultiplexor 1993 Specifications CSJ 0008-12-071 SPECIAL SPECIFICATION ITEM 6550 Drop/Insert Multiplexor/Demultiplexor 1.0 Description. This Item shall govern for the furnishing and installation of intelligent drop/insert

More information

SPECIAL SPECIFICATION 1806 Spread Spectrum Wireless Modem

SPECIAL SPECIFICATION 1806 Spread Spectrum Wireless Modem 1993 Specifications CSJ s 0902-48-442 & 0902-48-432 SPECIAL SPECIFICATION 1806 Spread Spectrum Wireless Modem 1. General. This Item shall govern for the furnishing and installation of Spread Spectrum Wireless

More information

1995 Metric CSJ , etc. SPECIAL SPECIFICATION ITEM D-I Muldem (Drop/Insert Multiplexor/Demultiplexor)

1995 Metric CSJ , etc. SPECIAL SPECIFICATION ITEM D-I Muldem (Drop/Insert Multiplexor/Demultiplexor) 1995 Metric CSJ 0924-06-156, etc. SPECIAL SPECIFICATION ITEM 6588 D-I Muldem (Drop/Insert Multiplexor/Demultiplexor) 1. Description. This Item shall govern for the furnishing and installation of intelligent

More information

SPECIAL SPECIFICATION 8590 Emergency Vehicle Traffic Signal Priority Control System

SPECIAL SPECIFICATION 8590 Emergency Vehicle Traffic Signal Priority Control System 2004 Specifications CSJ 0002-01-074, etc. SPECIAL SPECIFICATION 8590 Emergency Vehicle Traffic Signal Priority Control System 1. Description. This Item governs the furnishing and installation of emergency

More information

SPECIAL SPECIFICATION 8340 Dual Band Wireless Ethernet Radios

SPECIAL SPECIFICATION 8340 Dual Band Wireless Ethernet Radios 2004 Specifications CSJ 0914-00-280 SPECIAL SPECIFICATION 8340 Dual Band Wireless Ethernet Radios 1. Description. Furnish and install Dual Band Wireless Ethernet Radios (DBWERs) links for point-to-point

More information

This Special Provision covers the requirements for the installation and testing of fibre optic modems (FOM).

This Special Provision covers the requirements for the installation and testing of fibre optic modems (FOM). FIBRE OPTIC MODEMS - Item No. Special Provision No. 683S09 September 2007 1. SCOPE This Special Provision covers the requirements for the installation and testing of fibre optic modems (FOM). 2. REFERENCES

More information

SPECIAL SPECIFICATION 6004 Digital Card Rack Inductive Loop Detector Assembly

SPECIAL SPECIFICATION 6004 Digital Card Rack Inductive Loop Detector Assembly 2004 Specifications SPECIAL SPECIFICATION 6004 Digital Card Rack Inductive Loop Detector Assembly 1. Description. Furnish and install a digital card rack inductive loop detector assemblies. 2. Materials.

More information

SPECIAL SPECIFICATION 6574 Low Power Wireless Modem

SPECIAL SPECIFICATION 6574 Low Power Wireless Modem 2004 Specifications CSJ 1068-04-126, etc. SPECIAL SPECIFICATION 6574 Low Power Wireless Modem 1. Description. This work shall consist of furnishing and supplying a Low Power Wireless Modem at the locations

More information

FiberLink 4040 Series

FiberLink 4040 Series MANUAL FiberLink 4040 Series Four channels of audio over one single mode or multimode fiber. Installation and Operations Manual WWW.ARTEL.COM Contents Contents Welcome... 3 Features... 3 Package Contents...

More information

SPECIAL SPECIFICATION 1257 Digital Card Rack Non-Invasive Micro Loop Detector Assembly (8 Slot Rack)

SPECIAL SPECIFICATION 1257 Digital Card Rack Non-Invasive Micro Loop Detector Assembly (8 Slot Rack) 1993 Specifications CSJ 0924-06-147, etc. SPECIAL SPECIFICATION 1257 Digital Card Rack Non-Invasive Micro Loop Detector Assembly (8 Slot Rack) 1. Description. This Item shall govern for furnishing, and

More information

PRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian)

PRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian) PRODUCT SPECIFICATION FOR A 15 AND 75 kva, THREE PHASE MODULAR POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING (Varian) 1.0 General This specification covers the electrical characteristics and

More information

This special provision is for the installation and testing of the following equipment:

This special provision is for the installation and testing of the following equipment: FIBRE OPTIC MODEMS - Item No. Special Provision No. 683F18 April 2005 1. DESCRIPTION This special provision is for the installation and testing of the following equipment: Low Range Fibre Optic Modems

More information

LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING

LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING 1.0 General This specification covers the electrical characteristics and general

More information

User's Manual: Series 350T AC Current Input (External Sensor), DC-Powered Transmitters

User's Manual: Series 350T AC Current Input (External Sensor), DC-Powered Transmitters User's Manual: Series 350T AC Current Input (External Sensor), DC-Powered Transmitters Table of Contents Page Introduction 1 Description 1 Specifications 2 Installation 3 Calibration 4 General Maintenance

More information

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR WIRELESS INTERCONNECT FOR SIGN MOUNTED FLASHER

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR WIRELESS INTERCONNECT FOR SIGN MOUNTED FLASHER MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR WIRELESS INTERCONNECT FOR SIGN MOUNTED FLASHER OPR:DJA 1 of 5 C&T:APPR:JAR:DBP:09-01-11 FHWA:APPR:09-01-11 a. Description. This work consists

More information

Active CCTV Receiver Balun Installation Guide

Active CCTV Receiver Balun Installation Guide Active CCTV Receiver Balun 500015 Installation Guide P/N: 94-000304-C SE-000266-C Copyright Notice: Copyright 2009 MuxLab Inc. All rights reserved. Printed in Canada. No part of this publication may be

More information

Instruction Manual MT-945SL Four Channel Video Transmitter With Two Bi-Directional Data Channels

Instruction Manual MT-945SL Four Channel Video Transmitter With Two Bi-Directional Data Channels Instruction Manual MT-945SL Four Channel Video Transmitter With Two Bi-Directional Data Channels Copyright 2006, American Fibertek, Inc. 0307JD Table of Contents Functional Description... 3 Installation...

More information

WAVEFORM CORRECTOR (WAVEFORM CORRECTORS) REPLACES SURGE PROTECTION DEVICES (SPD) PREVIOUSLY KNOWN AS (TVSS)

WAVEFORM CORRECTOR (WAVEFORM CORRECTORS) REPLACES SURGE PROTECTION DEVICES (SPD) PREVIOUSLY KNOWN AS (TVSS) WAVEFORM CORRECTOR (WAVEFORM CORRECTORS) REPLACES SURGE PROTECTION DEVICES (SPD) PREVIOUSLY KNOWN AS (TVSS) 1 PART 1: GENERAL This section describes materials and installation requirements for low voltage

More information

2.2 American National Standards Institute Corporation and its applicable standards C39.1, C80.1, C89, C84.1.

2.2 American National Standards Institute Corporation and its applicable standards C39.1, C80.1, C89, C84.1. TECHNICAL SPECIFICATIONS for Single Phase, 1 to 3 KVA Power Conditioner with Regulation and Distribution Constant Power 3 (CP3) CP36508A 7/15/04 1.0 General This specification covers the electrical characteristics

More information

SPECIAL SPECIFICATION 6744 Spread Spectrum Radio

SPECIAL SPECIFICATION 6744 Spread Spectrum Radio 2004 Specifications CSJ 0924-06-244 SPECIAL SPECIFICATION 6744 Spread Spectrum Radio 1. Description. Furnish and install spread spectrum radio system. 2. Materials. Supply complete manufacturer specifications

More information

Instruction Manual Model M Switch, DPDT, Manual Select

Instruction Manual Model M Switch, DPDT, Manual Select Instruction Manual Model 1582-70M Switch, DPDT, Manual Select November 2018 Rev 0 STATUS MODEL 1582 CROSS TECHNOLOGIES INC. MANUAL SELECT POWER Data, drawings, and other material contained herein are proprietary

More information

MONITOR BRACKETS CCTV SYSTEMS. BT7510S Ex GST Inc GST. BT7511S Ex GST Inc GST. BT7512S Ex GST Inc GST. BT7518S Ex GST Inc GST. BT7513S Ex GST Inc GST

MONITOR BRACKETS CCTV SYSTEMS. BT7510S Ex GST Inc GST. BT7511S Ex GST Inc GST. BT7512S Ex GST Inc GST. BT7518S Ex GST Inc GST. BT7513S Ex GST Inc GST MONITOR BRACKETS BT7510S Small Flat Screen Bracket 20kg For small flat screen. Mounts screen only 20mm from wall. Security Allen Key provided Accommodates up to 20kg BT7511S Small Flat Screen Tilt Bracket

More information

Instruction Manual MX-480 Bi-directional Multi-Protocol Data

Instruction Manual MX-480 Bi-directional Multi-Protocol Data Instruction Manual MX-480 Bi-directional Multi-Protocol Data Copyright 2007, American Fibertek, Inc. 1210JD Table of Contents Functional Description...3 Installation...3 Power Source...3 Power Connection...4

More information

TECHNICAL DESCRIPTION

TECHNICAL DESCRIPTION TECHNICAL DESCRIPTION A.M. BROADCAST TRANSMITTER SENDER AM 3000 SS June 2001-1- Rev. B TRANSMITTER CHARACTERISTICS 1. BASIC OFFER The basic offer includes: One AM3000SS A.M. Medium Wave Solid State Broadcast

More information

RECOMMENDATION ITU-R BT.1367 *

RECOMMENDATION ITU-R BT.1367 * Rec. ITU-R BT.1367 1 RECOMMENDATION ITU-R BT.1367 * Serial digital fibre transmission system for signals Conforming to Recommendations ITU-R BT.656, ITU-R BT.799 and ITU-R BT.1120 (Question ITU-R 42/6)

More information

2520 Pulsed Laser Diode Test System

2520 Pulsed Laser Diode Test System Complete pulse test of laser diode bars and chips with dual photocurrent measurement channels 0 Pulsed Laser Diode Test System Simplifies laser diode L-I-V testing prior to packaging or active temperature

More information

F290X / F293X FOM II Series Fiber Optic Isolator Technical Manual

F290X / F293X FOM II Series Fiber Optic Isolator Technical Manual F290X / F293X FOM II Series Fiber Optic Isolator Technical Manual Revision G Copyright 2017 VERSITRON, Inc. 83 Albe Drive / Suite C Newark, DE 19702 www.versitron.com E031130243 PROPRIETARY DATA All data

More information

SPECIAL SPECIFICATION 6647 Automated Barrier Gate Assembly

SPECIAL SPECIFICATION 6647 Automated Barrier Gate Assembly 1995 Metric CSJ 0015-13-299 SPECIAL SPECIFICATION 6647 Automated Barrier Gate Assembly 1. Description. This Item shall govern for the furnishing and installation of an Automated Barrier Gate (ABG) assembly

More information

M-0418 REV:0

M-0418 REV:0 1 of 5 This specification sets forth the minimum requirements for purchase and installation of an aboveground Radar Detection Device (RDD) system for a real-time, stop bar vehicle-detection system that

More information

User's Manual: Series 450T AC Current Input (External Sensor), AC-Powered Transmitters

User's Manual: Series 450T AC Current Input (External Sensor), AC-Powered Transmitters User's Manual: Series 450T AC Current Input (External Sensor), AC-Powered Transmitters Table of Contents Page Introduction 1 Description 1 Specifications 2 Installation 3 Calibration 4 General Maintenance

More information

Preliminary Specification

Preliminary Specification Preliminary Specification CONTENTS 1.1 SCOPE 2 1.2 OPTICAL SPECIFICATION 2 1.3 BEAM DELIVERY FIBER SPECIFICATION 3 1.4 ALIGNMENT LASER 3 1.5 POWER DISTRIBUTION 3 1.6 WATER COOLING REQUIREMENTS 4 1.7 CONTROL

More information

LongReach II Active CCTV Receiver Hub [8P], [16P] Installation Guide

LongReach II Active CCTV Receiver Hub [8P], [16P] Installation Guide LongReach II Active CCTV Receiver Hub 500126 [8P], 500127 [16P] Installation Guide P/N: 94-000709-A SE-000709-A Copyright Notice: Copyright 2012 MuxLab Inc. All rights reserved. Printed in Canada. No part

More information

af i Instruction Manual MR-944C Four Channel Video Receiver With One Bi-Directional Multi-Protocol Data Channel american fibertek 11/30/2012 JPK

af i Instruction Manual MR-944C Four Channel Video Receiver With One Bi-Directional Multi-Protocol Data Channel american fibertek 11/30/2012 JPK af i american fibertek Instruction Manual MR-944C Four Channel Video Receiver With One Bi-Directional Multi-Protocol Data Channel 11/30/2012 JPK Table of Contents Functional Description... 3 Installation...

More information

OM7AT & OM7AR1 (Stand alone) ROM7AT & ROM7AR1 (Rack mount)

OM7AT & OM7AR1 (Stand alone) ROM7AT & ROM7AR1 (Rack mount) OM7AT & OM7AR1 (Stand alone) ROM7AT & ROM7AR1 (Rack mount) IRIG Time Code Electrical to Fiber Optic Transceiver Operating Manual Rev. 1.3 December 20, 2015 Luxcom Technologies Inc., 102 WALGREEN ROAD,

More information

Recirculating Loop System (No Frequency Shift) AMM C-RLS(nfs)-RM

Recirculating Loop System (No Frequency Shift) AMM C-RLS(nfs)-RM Recirculating Loop System (No Frequency Shift) AMM-100-8-70-C-RLS(nfs)-RM KEY FEATURES R F D R I V E R R E C I R C U L A T I N G L O O P S Y S T E M D I A G R A M Low Insertion Loss No O-rings Rack-mount

More information

SPECIAL PROVISION Description of Project, Scope of Contract and Sequence of Work

SPECIAL PROVISION Description of Project, Scope of Contract and Sequence of Work 2004 Specifications CSJ 0110-04-166 SPECIAL PROVISION 000--363 Description of Project, Scope of Contract and Sequence of Work 1. General. The work to be performed on this project consists of furnishing,

More information

ME7220A. Radar Test System (RTS) Target Simulation & Signal Analysis for Automotive Radar Exceptional Performance at an Affordable Price.

ME7220A. Radar Test System (RTS) Target Simulation & Signal Analysis for Automotive Radar Exceptional Performance at an Affordable Price. ME7220A Test System (RTS) 76 to 77 GHz Target Simulation & Signal Analysis for Automotive Exceptional Performance at an Affordable Price The Challenge The installation of collision warning and Adaptive

More information

SPECIAL SPECIFICATION LIGHTNING PROTECTION SYSTEM

SPECIAL SPECIFICATION LIGHTNING PROTECTION SYSTEM 2004 Specifications CSJ 3622-01-001, ETC. SPECIAL SPECIFICATION 8398 LIGHTNING PROTECTION SYSTEM 1. Description. This Special Specification governs the design and installation of Lightning Protection System

More information

SINGLE-PHASE VSV SWITCH

SINGLE-PHASE VSV SWITCH May 2006 Supercedes: March 2006 SINGLE-PHASE VSV SWITCH INSTALLATION AND OPERATING MANUAL Table of Content: Page I. General...2 II. Specifications...2 III. Installation...2 IV. Maintenance...4 V. VSV Power

More information

PRODUCT INFORMATION B&B ELECTRONICS. Port-Powered RS-232 Fiber Optic Modem with Handshake Support. Model 9PFLST. Description. RS-232 Connections

PRODUCT INFORMATION B&B ELECTRONICS. Port-Powered RS-232 Fiber Optic Modem with Handshake Support. Model 9PFLST. Description. RS-232 Connections -01-1/ 00 by B&B Electronics. All rights reserved. Model Port-Powered RS- Fiber Optic Modem with Handshake Support Description The allows any two pieces of RS- asynchronous serial equipment to communicate

More information

RFI & EMI Components and Subsystems

RFI & EMI Components and Subsystems RFI & EMI Components and Subsystems In 1979 Filter Networks began manufacturing RFI and EMI components. Filter Networks was acquired in 1997 by EMI Technologies. Our mission then, as now, was simple: to

More information

M302RM OPERATING MANUAL

M302RM OPERATING MANUAL M302RM OPERATING MANUAL The Model 302RM is a Linear, high voltage, differential amplifier designed to drive a capacitive load such as Conoptics 350, 360, 370 series E.O. modulators. The amplifier is DC

More information

2017 Advanced Energy Industries, Inc. PEII SERIES LOW-FREQUENCY POWER SUPPLIES 5 TO 60 KW

2017 Advanced Energy Industries, Inc. PEII SERIES LOW-FREQUENCY POWER SUPPLIES 5 TO 60 KW 2017 Advanced Energy Industries, Inc. PEII SERIES LOW-FREQUENCY POWER SUPPLIES 5 TO 60 KW Enhanced arc control with internal load matching for 40 khz reactive sputtering applications Page 2 The PEII power

More information

SPECIAL SPECIFICATION Inch LED Traffic Signal Lamp Unit

SPECIAL SPECIFICATION Inch LED Traffic Signal Lamp Unit 1993 Specifications SPECIAL SPECIFICATION 1201 12 Inch LED Traffic Signal Lamp Unit 1. Description. This specification describes the minimum acceptable design and performance requirements for a twelve

More information

PIRANHA 3 (3-phase, Power Conditioning Voltage Regulator)

PIRANHA 3 (3-phase, Power Conditioning Voltage Regulator) PRODUCT SPECIFICATION FOR A 15 THRU 500 kva, THREE PHASE, MODULAR POWER REGULATOR AND CONDITIONER PIRANHA 3 (3-phase, Power Conditioning Voltage Regulator) 1.0 General This specification covers the electrical

More information

Series CCS-37S/CS-37S Miniature DC 18 GHz Failsafe TRANSFER Coaxial Switch

Series CCS-37S/CS-37S Miniature DC 18 GHz Failsafe TRANSFER Coaxial Switch COAX SWITCHES Series CCS-37S/CS-37S PART NUMBER CCS-37S CS-37S DESCRIPTION Commercial Failsafe TRANSFER, DC-8GHz Elite Failsafe TRANSFER, DC-8GHz The CCS-37S/CS-37S is a long-life high performance transfer

More information

Instruction Manual RT-93285SL RR-93285SL Thirty-two Channel Video Multiplexer With Two Bi-directional Data Channels

Instruction Manual RT-93285SL RR-93285SL Thirty-two Channel Video Multiplexer With Two Bi-directional Data Channels Instruction Manual RT-93285SL RR-93285SL Thirty-two Channel Video Multiplexer With Two Bi-directional Data Channels Copyright 2006, American Fibertek, Inc. 0222JD Table of Contents Functional Description...3

More information

TOA PROFESSIONAL POWER AMP

TOA PROFESSIONAL POWER AMP Operating Instruction Manual TOA PROFESSIONAL POWER AMP Model P-150M, P-300M TOA ELECTRIC CO, LTD. KOBE, JAPAN Contents Precautions... 2 General Description... 2 Features... 3 Specifications... 4~5 Performance

More information

Overtravel of 3.5 mm max. Power source DC D5C-1DS0 D5C-1DP0 D5C-1DA0 AC D5C-1AS0 D5C-1AP0 D5C-1AA0 Antenna only D5C-00S0 D5C-00P0 D5C-00A0

Overtravel of 3.5 mm max. Power source DC D5C-1DS0 D5C-1DP0 D5C-1DA0 AC D5C-1AS0 D5C-1AP0 D5C-1AA0 Antenna only D5C-00S0 D5C-00P0 D5C-00A0 Touch Switch Unique 18 mm Capacitive Touch Switch with Choice of Three Actuators is Activated with Only a Very Slight Physical Contact Lightweight objects, such as thin wire or foil can be accurately detected.

More information

SL300 Snow Depth Sensor USL300 SNOW DEPTH SENSOR. Revision User Manual

SL300 Snow Depth Sensor USL300 SNOW DEPTH SENSOR. Revision User Manual USL300 SNOW DEPTH SENSOR Revision 1.1.2 User Manual 1 Table of Contents 1. Introduction... 3 2. Operation... 3 2.1. Electrostatic Transducer... 4 2.2. SL300 Analog Board... 4 2.3. SL300 Digital Circuit

More information

PROFESSIONAL POWER AMP

PROFESSIONAL POWER AMP Operating Instruction Manual PROFESSIONAL POWER AMP Model P-75D, P-150D, P-300D P-75D P-150D P-300D TOA Corporation KOBE, JAPAN Contents Precautions... 1 General Description... 2 Features... 2~ 3 Specifications...

More information

Series CCS-47/CS-47 High Power DC 12 GHz Failsafe TRANSFER Coaxial Switch

Series CCS-47/CS-47 High Power DC 12 GHz Failsafe TRANSFER Coaxial Switch COAX SWITCHES Series CCS-47/CS-47 PART NUMBER CCS-47 CS-47 DESCRIPTION Commercial Failsafe TRANSFER, DC-GHz Elite Failsafe TRANSFER, DC-GHz The CCS-47/CS-47 is a long-life high performance transfer switch

More information

General Application Notes Remote Sense Remote On / Off Output Trim Series Operation Parallel Operation...

General Application Notes Remote Sense Remote On / Off Output Trim Series Operation Parallel Operation... General... 28 Remote Sense... 29 Remote On / Off... 30 Output Trim... 30 Series Operation... 32 Parallel Operation... 33 Synchronization... 33 Power Good Signal... 34 Electro Magnetic Filter (EMI)... 34

More information

Series CCR-33K/CR-33K Miniature DC 33.5 GHz Failsafe SPDT Coaxial Switch

Series CCR-33K/CR-33K Miniature DC 33.5 GHz Failsafe SPDT Coaxial Switch PART NUMBER CCR-33K CR-33K DESCRIPTION Commercial Failsafe SPDT, DC-33.5GHz Elite Failsafe SPDT, DC-33.5GHz The CCR-33K/CR-33K is a broadband, SPDT, electromechanical, coaxial switch designed to switch

More information

Agilent 8761A/B Microwave Switches

Agilent 8761A/B Microwave Switches Agilent 8761A/B Microwave Switches Product Overview Product Description The Agilent Technologies 8761A and 8761B are single-pole, double-throw coaxial switches with excellent electrical and mechanical

More information

411LA Broadband Power Amplifier

411LA Broadband Power Amplifier 411LA Broadband Power Amplifier HIGH RF VOLTAGES MAY BE PRESENT AT THE OUTPUT OF THIS UNIT. All operating personnel should use extreme caution in handling these voltages and be thoroughly familiar with

More information

Part Numbers. Fiber Driver - ST/DB25M FIBER DRIVER

Part Numbers. Fiber Driver - ST/DB25M FIBER DRIVER January 2010 MD940A-F MD940A-M Part Numbers - ST/DB25F MD940A-F - ST/DB25M MD940A-M FIBER DRIVER CUSTOMER Order toll-free in the U.S.: 877-877-BBOX (outside U.S. call 724-746-5500) SUPPORT FREE technical

More information

Single-output models feature wide-range output adjustability to meet a wide variety of standard and user-specific output voltage requirements.

Single-output models feature wide-range output adjustability to meet a wide variety of standard and user-specific output voltage requirements. Bel Power Solutions MAP55 Series of power supplies provides reliable, tightly-regulated DC power for commercial and industrial systems. Wide-range AC input and full international safety, EMI, and ESD compliance

More information

TOSHIBA International Corp

TOSHIBA International Corp TOSHIBA International Corp GUIDE SPECIFICATIONS THREE PHASE UNINTERRUPTIBLE POWER SYSTEM TOSHIBA 4200FA 30 kva CT Internal Battery UPS GUIDE SPECIFICATIONS 1 (30 kva CT) 1.0 SCOPE 1.1 System This specification

More information

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK SIG:EMS 1 of 6 APPR:LWB:DBP:07-14-15 FHWA:APPR:07-28-15 a. Description. This work consists of site

More information

Ortel (Lucent) Fiber Optic Interface

Ortel (Lucent) Fiber Optic Interface Ortel (Lucent) Fiber Optic Interface 144-701-1 Serial Number May 5, 2009 Revision B ORTEL (LUCENT) FIBER OPTIC INTERFACE 1. GENERAL INFORMATION... 1 1.1. SCOPE OF OPTION... 1 1.2. PURPOSE OF EQUIPMENT...

More information

OP710. Multichannel Optical Power Meter Instruction Manual. (Also supports the OP710-ANX)

OP710. Multichannel Optical Power Meter Instruction Manual. (Also supports the OP710-ANX) Multichannel Optical Power Meter Instruction Manual (Also supports the OP710-ANX) www.optotest.com 1.805.987.1700 Contacting OptoTest Corporation 1.805.987.1700 (7:30 a.m. to 5 p.m. PST) www.optotest.com

More information

285E Series DIGITAL FIBER OPTIC AUDIO/DATA TRANSPORT SYSTEM

285E Series DIGITAL FIBER OPTIC AUDIO/DATA TRANSPORT SYSTEM 285E Series DIGITAL FIBER OPTIC AUDIO/DATA TRANSPORT SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability is assumed as a result

More information

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK

MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK MICHIGAN DEPARTMENT OF TRANSPORTATION SPECIAL PROVISION FOR TRAFFIC SIGNAL WIRELESS COMMUNICATIONS LINK SIG:CJS 1 of 6 APPR:EMS:DBP:06-29-17 FHWA:APPR:08-14-17 a. Description. This work consists of completing

More information

Contacts M39029 and Glenair signature solutions MIL-DTL Series III type

Contacts M39029 and Glenair signature solutions MIL-DTL Series III type EXTENDED DUTY CRIMP CONTACTS Mating End Size Wire Accomodation How-To-Order Extended Duty Crimp No. Glenair Part No. No. Copper alloy, plated with 5 μinches gold over 45 μinches palladium alloy. Rated

More information

Series CCR-33K/CR-33K Miniature DC 33.5 GHz Latching SPDT Coaxial Switch

Series CCR-33K/CR-33K Miniature DC 33.5 GHz Latching SPDT Coaxial Switch COAX SWITCHES Series CCR-33K/CR-33K PART NUMBER CCR-33K CR-33K DESCRIPTION Commercial Latching SPDT, DC-33.5GHz Elite Latching SPDT, DC-33.5GHz The CCR-33K/CR-33K is a broadband, SPDT, electromechanical,

More information

Series CCRS-53S/CRS-53S Miniature DC 26.5 GHz Latching 2P3T Coaxial Switch

Series CCRS-53S/CRS-53S Miniature DC 26.5 GHz Latching 2P3T Coaxial Switch COAX SWITCHES Series CCRS-53S/CRS-53S PART NUMBER CCRS-53S CRS-53S DESCRIPTION Commercial Latching 2P3T, DC-26.5GHz Elite Latching 2P3T, DC-26.5GHz The CCRS-53S/CRS-53S is a broadband, 2P3T, electromechanical

More information

STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 919 RAILROAD PREEMPTION INTERFACE. January 15, 2016

STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 919 RAILROAD PREEMPTION INTERFACE. January 15, 2016 STATE OF OHIO DEPARTMENT OF TRANSPORTATION SUPPLEMENTAL SPECIFICATION 919 RAILROAD PREEMPTION INTERFACE January 15, 2016 919.01 Traffic Signal Cabinet and Controller Unit General Requirements 919.02 Approved

More information

INSTRUCTION MANUAL MODEL 2779 SUBCARRIER MODULATOR

INSTRUCTION MANUAL MODEL 2779 SUBCARRIER MODULATOR INSTRUCTION MANUAL MODEL 2779 SUBCARRIER MODULATOR Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., and may not be reproduced or duplicated in any form without

More information

Model 3210C. 100 Ampere AC Current Standard. Operating Manual

Model 3210C. 100 Ampere AC Current Standard. Operating Manual Model 3210C 100 Ampere AC Current Standard Operating Manual This page intentionally left blank. 3210C OPERATORS MANUAL Serial No. Win-man\3210C.wpd This page intentionally left blank. 3210C OPERATORS MANUAL

More information

Electronic Circuit Breaker with reset input ESS20-1..

Electronic Circuit Breaker with reset input ESS20-1.. Electronic Circuit Breaker with reset input ESS0-.. Description The special device ESS0-.. is a further extension of the product line electronic circuit breakers. Type ESS0-.. has a width of only. mm and

More information

Instruction Manual MTX-8485C MRX-8485C Four Channel Video Multiplexer with Bi-directional Data

Instruction Manual MTX-8485C MRX-8485C Four Channel Video Multiplexer with Bi-directional Data Instruction Manual MTX-8485C MRX-8485C Four Channel Video Multiplexer with Bi-directional Data Copyright 2005, American Fibertek, Inc. 1027JD Table of Contents Functional Description...3 Installation...3

More information

PSI-2450 INTEGRATED CONTROLLER USER GUIDE

PSI-2450 INTEGRATED CONTROLLER USER GUIDE PSI-2450 INTEGRATED CONTROLLER PSI-2400-10 LASER DIODE CONTROLLER & PSI-1204-10 MODULATOR BIAS CONTROLLER USER GUIDE Revision B Photonic Systems, Inc. Tel: 978-670-4990 900 Middlesex Turnpike Fax: 978-670-2510

More information

SINGLE-PHASE VSV SWITCH

SINGLE-PHASE VSV SWITCH Revision: September 2009 Supersedes: August 2007 SINGLE-PHASE VSV SWITCH INSTALLATION AND OPERATING MANUAL Table of Content: Page I. General...2 II. Specifications...2 III. Installation...3 IV. Maintenance...5

More information

V1.3. TBLC08 50mH AC-LISN TBLC08

V1.3. TBLC08 50mH AC-LISN TBLC08 V1.3 TBLC08 The TBLC08 is a Line Impedance Stabilization Network for the measurement of line-conducted interference within the range of 9kHz to 30MHz, according to the CISPR16 standard. The device is designed

More information

Fiber Optics. Plastic Fiber Optic Transmitter Diode Plastic Connector Housing SFH756 SFH756V

Fiber Optics. Plastic Fiber Optic Transmitter Diode Plastic Connector Housing SFH756 SFH756V Fiber Optics Plastic Fiber Optic Transmitter Diode Plastic Connector Housing SFH756 Features 2.2 mm Aperture holds Standard 1000 Micron Plastic Fiber No Fiber Stripping Required Good Linearity (Forward

More information

INSTRUCTION MANUAL MODEL 2455T SUBCARRIER MODULATOR

INSTRUCTION MANUAL MODEL 2455T SUBCARRIER MODULATOR INSTRUCTION MANUAL MODEL 2455T SUBCARRIER MODULATOR Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., and may not be reproduced or duplicated in any form

More information

FIBER105.TIF OUTLINE DIMENSIONS in inches (mm) .176 (4.47).165 (4.19) .500 MIN (12.7) FIBER203.DIM. Pinout 1. Capacitor 2. VÙÙ 3.

FIBER105.TIF OUTLINE DIMENSIONS in inches (mm) .176 (4.47).165 (4.19) .500 MIN (12.7) FIBER203.DIM. Pinout 1. Capacitor 2. VÙÙ 3. FEATURES Converts fiber optic input signals to TTL digital outputs Typical sensitivity 500 nw peak ( 33 dbm) Single 5 V supply requirement Edge detection circuitry gives 20 db minimum dynamic range, low

More information

INSTRUCTION MANUAL OTOT-1000C-FQ WIDE-BAND 1550NM DIRECT-MOD QAM TRANSMITTER. 1,000 MHz Bandwidth / Optical Output Power is +9dBm (OTOT-1000C-09-FQ)

INSTRUCTION MANUAL OTOT-1000C-FQ WIDE-BAND 1550NM DIRECT-MOD QAM TRANSMITTER. 1,000 MHz Bandwidth / Optical Output Power is +9dBm (OTOT-1000C-09-FQ) INSTRUCTION MANUAL OTOT-1000C-FQ WIDE-BAND 1550NM DIRECT-MOD QAM TRANSMITTER 1,000 MHz Bandwidth / Optical Output Power is +9dBm (OTOT-1000C-09-FQ) Phone: (209) 586-1022 (800) 545-1022 Fax: (209) 586-1026

More information

FMT633S STEREO SYNTHESIZER MODULATOR INSTRUCTION BOOK IB

FMT633S STEREO SYNTHESIZER MODULATOR INSTRUCTION BOOK IB FMT633S STEREO SYNTHESIZER MODULATOR INSTRUCTION BOOK IB 6114-01 TABLE OF CONTENTS GENERAL DESCRIPTION: 1 SPECIFICATIONS: 2 FUNCTIONAL DESCRIPTION: 3 INSTALLATION & OPERATING INSTRUCTIONS: 3-4 CAUTION:

More information

Low Voltage Power Factor Correction Equipment Specifications Automatic, Automatic Detuned, Automatic Tuned

Low Voltage Power Factor Correction Equipment Specifications Automatic, Automatic Detuned, Automatic Tuned Low Voltage Power Factor Correction Equipment Specifications Automatic, Automatic Detuned, Automatic Tuned Part 1 - General Scope and Product Description 1.0 This specification contains the minimum design

More information

SECTION GPS WIRELESS CLOCK SYSTEMS

SECTION GPS WIRELESS CLOCK SYSTEMS PART 1 GENERAL 1.1 SECTION INCLUDES A. G.P.S. Receiver B. Primary Transmitter C. Satellite Transmitter D. Analog Clocks E. Digital Clocks 1.2 REGULATORY REQUIREMENTS SECTION 27 53 13 GPS WIRELESS CLOCK

More information

Customer P/N: UDE P/N: GDC-1U2AVN13. Description: RJ45 1X1 Tab Down Through Hole 10G Base-T Contact Area : 30μ Gold LED:L-Yellow/Green; R-Green

Customer P/N: UDE P/N: GDC-1U2AVN13. Description: RJ45 1X1 Tab Down Through Hole 10G Base-T Contact Area : 30μ Gold LED:L-Yellow/Green; R-Green To: Customer P/N: UDE P/N: Description: RJ45 1X1 Tab Down Through Hole 10G Base-T Contact Area : 30μ Gold LED:L-Yellow/Green; R-Green Spec No. GDC0013-00 Update Date 2015/7/7 Revision C Approved Checked

More information

Model MV106J/MV116J. ±10nVdc to ±11Vdc Precision DC Voltage Standard Source. Operating Manual

Model MV106J/MV116J. ±10nVdc to ±11Vdc Precision DC Voltage Standard Source. Operating Manual Model MV106J/MV116J ±10nVdc to ±11Vdc Precision DC Voltage Standard Source Operating Manual This page intentionally left blank. MV 106 & MV116 OPERATORS MANUAL Serial No. Win-man\mvman.wpd This page intentionally

More information

StatiVolt. Inverter UPS Systems. Features. Contents

StatiVolt. Inverter UPS Systems. Features. Contents Redundant, clean, sine-wave AC power ensures a high availability of mission-critical safety devices, instrumentation, alarms, controls and computers. Robust, StatiVolt UPS Systems are designed and built

More information

WIRELESS INSULATOR POLLUTION MONITORING SYSTEM

WIRELESS INSULATOR POLLUTION MONITORING SYSTEM SYSTEM OVERVIEW Pollution monitoring of high voltage insulators in electrical power transmission and distribution systems, switchyards and substations is essential in order to minimise the risk of power

More information

SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches

SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches PART 1 GENERAL 1.01 Scope Furnish and install automatic transfer switches (ATS) with number of poles, amperage, voltage, and withstand

More information

Vi6208, Vi6216, Vi6232 Vi6308, Vi6316, Vi6332

Vi6208, Vi6216, Vi6232 Vi6308, Vi6316, Vi6332 MODELs Vi6208, Vi6216, Vi6232 Vi6308, Vi6316, Vi6332 Automatic Video Compensation UTP Receiver Hubs User s Manual 7810 Trade Street, Suite 100 San Diego, CA 92121, U.S.A. Phone: (858) 484-5209 Fax: (858)

More information

Series CCR-53S/CR-53S Miniature DC 26.5 GHz Latching SPDT Coaxial Switch

Series CCR-53S/CR-53S Miniature DC 26.5 GHz Latching SPDT Coaxial Switch PART NUMBER CCR-53S CR-53S DESCRIPTION Commercial Latching SPDT, DC-26.5GHz Elite Latching SPDT, DC-26.5GHz The CCR-53S/CR-53S is a broadband, SPDT, electromechanical, coaxial switch designed to switch

More information

Series CCR-33S/CR-33S Miniature DC 18 GHz/DC-22 GHz Failsafe SPDT Coaxial Switch

Series CCR-33S/CR-33S Miniature DC 18 GHz/DC-22 GHz Failsafe SPDT Coaxial Switch COAX SWITCHES Series CCR-33S/CR-33S PART NUMBER CCR-33S CR-33S DESCRIPTION Commercial Failsafe SPDT, DC-18GHz Elite Failsafe SPDT, DC-22GHz The CCR-33S/CR-33S is a broadband, SPDT, electromechanical, coaxial

More information

TIA-525 Optical/Electrical Converter Operating Instructions

TIA-525 Optical/Electrical Converter Operating Instructions TIA-525 Optical/Electrical Converter Operating Instructions Contents Introduction... 1 Specifications... 2 Unpacking and Inspection... 3 Battery Replacement... 3 Controls... 4 Operating Considerations...

More information

Pin Contacts Military Part No. Copper alloy, plated with 5 μinches gold over 45 μinches palladium alloy. Rated to 1500 cycles of durability.

Pin Contacts Military Part No. Copper alloy, plated with 5 μinches gold over 45 μinches palladium alloy. Rated to 1500 cycles of durability. EXTENDED DUTY CRIMP CONTACTS SIZE #12 COAXIAL CONTACTS Mating End Size Wire Accomodation How-To-Order Extended Duty Crimp No. Glenair Part No. No. Copper alloy, plated with 5 μinches gold over 45 μinches

More information