HFD /XXX. h 479. Schmitt Input, Non-Inverting TTL Output Receiver
|
|
|
- Rosaline Gilmore
- 5 years ago
- Views:
Transcription
1 FEATURES Converts fiber optic input signals to TTL totem pole outputs Maximum sensitivity 1.5 µw peak (-28.2 dbm) Wide variety of cable options, operates with 50/125, 62.5/125, and 100/140 µm cables Schmitt circuitry gives 17dB minimum dynamic range and low Pulse Width Distortion Operates up to 200K bps NRZ Designed to operate with Honeywell 850 nm LEDs Single 5 V supply requirement Wave solderable Mounting options SMA single hole ST single hole SMA PCB ST PCB SMA 4 hole DESCRIPTION The HFD /XXX is a sensitive Schmitt triggered optical receiver designed for use in short distance, 850 nm fiber optic systems. The bipolar integrated receiver circuit has internal voltage regulation. The HFD /XXX also uses an internal photodiode. The TTL non-inverting output allows the HFD /XXX to be directly interfaced with standard digital TTL circuits. APPLICATION The HFD /XXX fiber optic receiver converts the optical signal in a point to point data communications fiber optic link to a TTL output. It is mounted in a fiber optic connector that aligns the optical axis of the component to the axis of the optical fiber. Electrical isolation is important in obtaining the maximum performance of this high sensitivity receiver. Shielding can reduce coupled noise and allow maximum sensitivity to be obtained. This can include the use of ground planes in the PCB, shielding around the device, and shielding around the leads. h 479
2 APPLICATION (continued) An internal voltage regulator allows operation with a 5 volt supply. An external bypass capacitor (0.1 µf) between VÙÙ (pin 1) and ground (pin 3) is recommended for maximum power supply noise rejection. Honeywell also offers companion transmitters designed to operate in conjunction with the HFD /XXX. Optical power (photons) from the fiber strikes the photodiode and is converted to electrical current. The current is converted into voltage in the transimpedance preamplifier. The Schmitt trigger circuitry in the comparator stage provides proper output signals. The Schmitt detection circuit monitors the input preamplifier, and triggers when its output exceeds present levels. Preset levels are above worst case RMS noise level, with 1 x 10ø bit error rate, while low enough for enough sensitivity to allow operation over long links. This circuitry recognizes positive and negative going input signals. When the optical input goes from low to high, the electrical output changes to "1" (high). The output changes to "0" (low) when the optical input goes from high to low. Bandwidth has been limited to minimize noise problems. The output of the Schmitt Trigger detector stage is designed for good pulse width distortion (PWD). 480 h
3 ELECTRO-OPTICAL CHARACTERISTICS(VÙÙ = 5.0 V ±0.5 VDC, -40 C < TÙ < +85 C unless otherwise stated) PARAMETER SYMBOL MIN TYP MAX UNITS Minimum Input Sensitivity PÛÜ (Peak) µw T= 25 C High Level Logic Output Voltage VÏÝ V Low Level Logic Output Voltage VÏÚ V Power Supply Current IÙÙ 6 12 ma Rise Time tß 12 ns Fall Time t 3 ns Pulse Width Distortion PWD % T = 25 C Bandwidth BW 200 khz Output Impedance IÞ 20 í TEST CONDITIONS 100 µm core fiber Duty Cycle = 50%, 850 µm PÛÜ 1.5 µw, VÙÙ = 5.0 VDC PÛÜ 0.1 µw, VÙÙ = 5.0 VDC IÏ 16 ma PÛÜ 1.5µW, VÏ = 0.4 to 2.4V PÛÜ 0.1µW, VÏ = 2.4 to 0.4V f = 20 khz, Duty Cycle = 50% PÛÜ 1.5 µw peak PÛÜ 100 µw PÛÜ 1.0µW, Duty Cycle = 50% ABSOLUTE MAXIMUM RATINGS (Tcase = 25 C unless otherwise noted) Storage temperature Supply voltage Lead solder temperature Junction temperature -40 to +100 C +4.5 to +7.0 V 260 C for 10 s 150 C Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED OPERATING CONDITIONS Operating temperature -40 to +100 C Supply voltage +4.5 to +7.0 V Optical input power 1.5 to 100 µw Optical signal pulse width > 4 µs h 481
4 ORDER GUIDE Description Fiber Optic Schmitt Input, Non inverting, TTL Output Receiver MOUNTING OPTIONS Catalog Listing HFD /XXX Substitute XXX with one of the following 3 letter combinations SMA single hole - AAA ST single hole - BAA SMA PCB - ABA ST PCB - BBA SMA 4 hole - ADA Dimensions on page 441 CAUTION The inherent design of this component causes it to be sensitive to electrostatic discharge (ESD). To prevent ESD-induced damage and/or degradation to equipment, take normal ESD precautions when handling this product. FIBER INTERFACE Honeywell detectors are designed to interface with multimode fibers with sizes (core/cladding diameters) ranging from 50/125 to 200/230 microns. Honeywell performs final tests using 100/140 micron core fiber. The fiber chosen by the end user will depend upon a number of application issues (distance, link budget, cable attenuation, splice attenuation, and safety margin). The 50/125 and 62.5/125 micron fibers have the advantages of high bandwidth and low cost, making them ideal for higher bandwidth installations. The use of 100/140 and 200/230 micron core fibers results in greater power being coupled by the transmitter, making it easier to splice or connect in bulkhead areas. Optical cables can be purchased from a number of sources. BLOCK DIAGRAM FIBER101.SCH SWITCHING WAVEFORM FIBER003.CIR 482 h
5 Fig. 1 Pulse Width Distortion vs Temperature Fig. 2 Pulse Width Distortion vs Frequency FIBER038.GRA FIBER039.GR Fig. 3 Pulse Width Distortion vs Optical Input Power Fig. 4 Propagation Delay vs Optical Input Power FIBER041.GR FIBER040.GRA h 483
6 European Connectorized Receivers Honeywell receiver components are available in the following connector styles. Each style has a three-digit reference used in the order guides. SMA SINGLE HOLE MOUNTING (REF.: AAA) ST SINGLE HOLE MOUNTING (REF.: BAA) SMA PCB MOUNTING (REF.: ABA) Honeywell Optoelectronics reserves the right to make changes at any time in order to improve design and 441
7 European Connectorized Receivers ST PCB MOUNTING (REF.: BBA) SMA 4 HOLE MOUNTING (REF.: ADA) 442 Honeywell Optoelectronics reserves the right to make changes at any time in order to improve design and
HFD3029. Schmitt Input, Non-Inverting TTL Output Receiver
FEATURES Converts fiber optic input signals to TTL totem pole outputs Sensitivity is 1.5 µw peak (-28.2 dbm) Single 5 V supply requirement Schmitt circuitry gives 17 db dynamic range and low Pulse Width
FIBER105.TIF OUTLINE DIMENSIONS in inches (mm) .176 (4.47).165 (4.19) .500 MIN (12.7) FIBER203.DIM. Pinout 1. Capacitor 2. VÙÙ 3.
FEATURES Converts fiber optic input signals to TTL digital outputs Typical sensitivity 500 nw peak ( 33 dbm) Single 5 V supply requirement Edge detection circuitry gives 20 db minimum dynamic range, low
HFD Mbit Direct Coupled Receiver
FEATURES Converts fiber optic input signals to TTL digital outputs Typical sensitivity 2 µw (-27 dbm) Single 5 V supply requirement Direct coupled receiver circuit Open collector output Microlens optics
European Connectorized Receivers
European Connectorized Receivers Honeywell receiver components are available in the following connector styles. Each style has a three-digit reference used in the order guides. SMA SINGLE HOLE MOUNTING
Fiber Optic LAN Components VF45 Quad Transceiver for 10Mb/s and 100Mb/s Ethernet
FEATURES Key component for making a fiber optic Ethernet truly scalable and switchable from 10 to 100Mb/s Ethernet. Innovative NEW interconnect is cost competitive with copper solutions, thus enabling
HFD Fiber Optic LAN Components 1.25Gbps PIN Plus Preamplifier with RSSI
with RSSI FEATURES rates > 1 GHz PIN detector, preamplifier, and bypass filtering in a TO-46 hermetic package 5V or 3.3V operation GaAs PIN detector and Transimpedance amplifier Differential Output for
The HFBR-1604 is a selected version of the HFBR-1602, with power specified to meet the
SERCOS Fiber Optic Transmitters and Receiver Technical Data HFBR-0600 Series Features Fully Compliant to SERCOS Optical Specifications Optimized for 1 mm Plastic Optical Fiber Compatible with SMA Connectors
Distributed by: www.jameco.com -800-83-22 The content and copyrights of the attached material are the property of its owner. 25 Megabaud Versatile Link The Versatile Fiber Optic Connection Technical Data
Features. Applications
HFBR-8 Series HFBR-8 Transmitter HFBR-8 Receiver Megabaud Versatile Link Fiber Optic Transmitter and Receiver for mm POF and µm HCS Data Sheet Description The HFBR-8 Series consists of a fiber-optic transmitter
Fiber Optic Receiver. OPF520 Series. OPF520 Series
Low Cost plastic cap package Designed to self align in the bore of standard fiber optic receptacles Press fit simplifies installation Optimized for fiber optic applications using 50 to 200 micron fiber
Data Sheet HFBR-1506AFZ/HFBR-2506AFZ. Full Metal Fiber Optic SMA Transmitters and Receivers for 16 MBd SERCOS Applications. Description.
HFBR-0AFZ/HFBR-20AFZ Full Metal Fiber Optic SMA Transmitters and Receivers for MBd SERCOS Applications Data Sheet Description SERCOS, an acronym for SErial Realtime COmmunications Systems, is a standard
12 Megabaud Versatile Link Fiber Optic Transmitter and Receiver for 1 mm POF and 200 μm HCS. Features. Applications
HFBR-EZ Transmitter HFBR-EZ Receiver Megabaud Versatile Link Fiber Optic Transmitter and Receiver for mm POF and μm HCS Data Sheet Description The HFBR-EZ transmitter is an LED in a low cost plastic housing
Data Sheet. HFBR-1506AMZ/HFBR-2506AMZ Fiber Optic SMA Transmitters and Receivers for 16 MBd SERCOS Applications. Description. Features.
HFBR-0AMZ/HFBR-20AMZ Fiber Optic SMA Transmitters and Receivers for MBd SERCOS Applications Data Sheet Description SERCOS, an acronym for SErial Realtime COmmunications Systems, is a standard digital interface
Single Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from + V to + V Dual Supply Capability from. V to 8 V Excellent Load
Single Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from V to V Dual Supply Capability from. V to 8 V Excellent Load Drive
OPF2416, OPF2416T, OPF2416TC
Features: Up to 155Mbps operation 850nm wavelength ST style port Wave solderable Wide temperature range Description: The OPF2416 family is a low cost solution for high speed fiber optic communications
Single Supply, Low Power Triple Video Amplifier AD813
a FEATURES Low Cost Three Video Amplifiers in One Package Optimized for Driving Cables in Video Systems Excellent Video Specifications (R L = 15 ) Gain Flatness.1 db to 5 MHz.3% Differential Gain Error.6
Data Sheet. HFBR-1312TZ Transmitter HFBR-2316TZ Receiver nm Fiber Optic Transmitter and Receiver. Description. Features.
HFBR-11TZ Transmitter HFBR-1TZ Receiver 100 nm Fiber Optic Transmitter and Receiver Data Sheet Description The HFBR-11TZ Transmitter and HFBR-1TZ Receiver are designed to provide the most cost-effective
Dual, Current Feedback Low Power Op Amp AD812
a FEATURES Two Video Amplifiers in One -Lead SOIC Package Optimized for Driving Cables in Video Systems Excellent Video Specifications (R L = ): Gain Flatness. db to MHz.% Differential Gain Error. Differential
Data Sheet. HFBR-0300Z Series HFBR-1312TZ Transmitter HFBR-2316TZ Receiver nm Fiber Optic Transmitter and Receiver. Features.
HFBR-000Z Series HFBR-TZ Transmitter HFBR-TZ Receiver 00 nm Fiber Optic Transmitter and Receiver Data Sheet Description The HFBR-000Z Series is designed to provide the most cost-effective 00 nm fiber optic
SGM9111 8MHz Rail-to-Rail Composite Video Driver with 6dB Gain
PRODUCT DESCRIPTION The SGM9111 is single rail-to-rail 5-pole output reconstruction filter with a -3dB bandwidth of 8MHz and a slew rate of 3.8V/µs. Operating from single supplies ranging from 3.V to 5.5V
SGM9111 8MHz Rail-to-Rail Composite Video Driver with 6dB Gain
SGM9111 8MHz Rail-to-Rail Composite GENERAL DESCRIPTION The SGM9111 is a single rail-to-rail -pole output reconstruction filter with a -3dB bandwidth of 8MHz and 3V/µs slew rate. Operating from single
AD9300 SPECIFICATIONS ELECTRICAL CHARACTERISTICS ( V S = 12 V 5%; C L = 10 pf; R L = 2 k, unless otherwise noted) COMMERCIAL 0 C to +70 C Test AD9300K
a FEATURES 34 MHz Full Power Bandwidth 0.1 db Gain Flatness to 8 MHz 72 db Crosstalk Rejection @ 10 MHz 0.03 /0.01% Differential Phase/Gain Cascadable for Switch Matrices MIL-STD-883 Compliant Versions
HFBR-1505AFZ/2505AFZ (SMA Tx/Rx for SERCOS) HFBR-1515BFZ/2515BFZ (ST Tx/Rx for PROFIBUS) HFBR-1505CFZ/2505CFZ (SMA Tx/Rx for INTERBUS-S)
HFBR-0AFZ/20AFZ (SMA Tx/Rx for SERCOS) HFBR-BFZ/2BFZ (ST Tx/Rx for PROFIBUS) HFBR-0CFZ/20CFZ (SMA Tx/Rx for INTERBUS-S) Full Metal Fiber Optic Transmitters and Receivers for SERCOS, PROFIBUS and INTERBUS-S
INGAAS FAST PIN (RF) AMPLIFIED PHOTODETECTORS
INGAAS FAST PIN (RF) AMPLIFIED PHOTODETECTORS High Signal-to-Noise Ratio Ultrafast up to 9.5 GHz Free-Space or Fiber-Coupled InGaAs Photodetectors Wavelength Range from 750-1650 nm FPD310 FPD510-F https://www.thorlabs.com/newgrouppage9_pf.cfm?guide=10&category_id=77&objectgroup_id=6687
Single Supply, Low Power, Triple Video Amplifier AD8013
a FEATURES Three Video Amplifiers in One Package Drives Large Capacitive Load Excellent Video Specifications (R L = 5 ) Gain Flatness. db to MHz.% Differential Gain Error. Differential Phase Error Low
Low Cost, General Purpose High Speed JFET Amplifier AD825
a FEATURES High Speed 41 MHz, 3 db Bandwidth 125 V/ s Slew Rate 8 ns Settling Time Input Bias Current of 2 pa and Noise Current of 1 fa/ Hz Input Voltage Noise of 12 nv/ Hz Fully Specified Power Supplies:
Data Sheet. AFBR-S10TR001Z Compact 650 nm Analog Transceiver with Compact Versatile-Link Connector for Sensing Over POF. Description.
AFBR-STRZ Compact 65 nm Analog Transceiver with Compact Versatile-Link Connector for Sensing Over POF Data Sheet Description Avago Technologies' AFBR-STRZ transceiver provides system designers with the
Dual Channel, High Speed Optocouplers Technical Data
Dual Channel, High Speed Optocouplers Technical Data HCPL-2530 HCPL-2531 HCPL-4534 HCPL-0530 HCPL-0531 HCPL-0534 Features 15 kv/µs Minimum Common Mode Transient Immunity at V CM = 1500 V (HCPL-4534/0534)
High Common-Mode Voltage Difference Amplifier AD629
a FEATURES Improved Replacement for: INAP and INAKU V Common-Mode Voltage Range Input Protection to: V Common Mode V Differential Wide Power Supply Range (. V to V) V Output Swing on V Supply ma Max Power
RoHS compliant 850 nm Multi-mode Transceiver (1000BASE-SX) 2 5, LC Duplex Connector, 3.3 V Gbd Fiber Channel/1.25 Gigabit Ethernet
Features RoHS compliant Compliant with IEEE 802.3z Gigabit Ethernet standard Compliant with Fiber Channel standard Industry standard 2 5 footprint LC duplex connector Single power supply 3.3V Class 1 laser
Improved Second Source to the EL2020 ADEL2020
Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling
Ultrafast Comparators AD96685/AD96687
a FEATURES Fast: 2.5 ns Propagation Delay Low Power: 118 mw per Comparator Packages: DIP, SOIC, PLCC Power Supplies: +5 V, 5.2 V Logic Compatibility: ECL 50 ps Delay Dispersion APPLICATIONS High Speed
Data Sheet. HFBR-1312T Transmitter HFBR-2316T Receiver 1300 nm Fiber Optic Transmitter and Receiver. Description. Features. Applications.
HFBR-11T Transmitter HFBR-1T Receiver 100 nm Fiber Optic Transmitter and Receiver Data Sheet Description The HFBR-000 Series is designed to provide the most cost-effective 100 nm fiber optic links for
PART TOP VIEW V EE 1 V CC 1 CONTROL LOGIC
19-1331; Rev 1; 6/98 EVALUATION KIT AVAILABLE Upstream CATV Driver Amplifier General Description The MAX3532 is a programmable power amplifier for use in upstream cable applications. The device outputs
Dual-Rate Fibre Channel Limiting Amplifier
19-375; Rev 1; 7/3 Dual-Rate Fibre Channel Limiting Amplifier General Description The dual-rate Fibre Channel limiting amplifier is optimized for use in dual-rate.15gbps/1.65gbps Fibre Channel optical
250 MHz, General Purpose Voltage Feedback Op Amps AD8047/AD8048
5 MHz, General Purpose Voltage Feedback Op Amps AD8/AD88 FEATURES Wide Bandwidth AD8, G = + AD88, G = + Small Signal 5 MHz 6 MHz Large Signal ( V p-p) MHz 6 MHz 5.8 ma Typical Supply Current Low Distortion,
622Mbps, Ultra-Low-Power, 3.3V Transimpedance Preamplifier for SDH/SONET
19-1601; Rev 2; 11/05 EVALUATION KIT AVAILABLE 622Mbps, Ultra-Low-Power, 3.3V General Description The low-power transimpedance preamplifier for 622Mbps SDH/SONET applications consumes only 70mW at = 3.3V.
SGM ns, Low-Power, 3V/5V, Rail-to-Rail Input Single-Supply Comparator
45ns, Low-Power, 3V/5V, Rail-to-Rail GENERAL DESCRIPTION The is a single high-speed comparator optimized for systems powered from a 3V or 5V supply. The device features high-speed response, low-power consumption,
HOD /BBA HOD /BBA
FEATURES Full duplex over single fiber DC to 60 MHz link bandwidth Link budgets of km [.4 miles] or greater 40 db isolation Low profile ST housing Other options available VCSEL is Class eye safe APPLICATIONS
HA MHz, High Slew Rate, High Output Current Buffer. Description. Features. Applications. Ordering Information. Pinouts.
SEMICONDUCTOR HA-2 November 99 Features Voltage Gain...............................99 High Input Impedance.................... kω Low Output Impedance....................... Ω Very High Slew Rate....................
Low Power. Video Op Amp with Disable AD810 REV. A. Closed-Loop Gain and Phase vs. Frequency, G = +2, R L = 150, R F = 715 Ω
CLOSED-LOOP db SHIFT Degrees DIFFERENTIAL % DIFFERENTIAL Degrees a FEATURES High Speed MHz Bandwidth ( db, G = +) MHz Bandwidth ( db, G = +) V/ s Slew Rate ns Settling Time to.% ( = V Step) Ideal for Video
Fiber Optic Transmitters and Receivers for SERCOS, PROFIBUS and INTERBUS-S Applications. Technical Data
Fiber Optic Transmitters and Receivers for SERCOS, PROFIBUS and INTERBUS-S Applications Technical Data HFBR-0A/20A (SMA Tx/Rx for SERCOS) HFBR-B/2B (ST Tx/Rx for PROFIBUS) HFBR-0C/20C (SMA Tx/Rx for INTERBUS-S)
1.25Gbps/2.5Gbps, +3V to +5.5V, Low-Noise Transimpedance Preamplifiers for LANs
19-4796; Rev 1; 6/00 EVALUATION KIT AVAILABLE 1.25Gbps/2.5Gbps, +3V to +5.5V, Low-Noise General Description The is a transimpedance preamplifier for 1.25Gbps local area network (LAN) fiber optic receivers.
ADG918/ADG919. Wideband 4 GHz, 43 db Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, 2:1 Mux/SPDT Switches
Wideband 4 GHz, 43 db Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, 2:1 Mux/SPDT Switches ADG918/ FEATURES Wideband switch: 3 db @ 4 GHz Absorptive/reflective switches High off isolation (43 db @ 1 GHz) Low
ODL 50 Series II Lightwave Data Link
ODL 50 Series II Lightwave Data Link ODL 50 Series II Lightwave Data Link Features Economical package utilizes low-cost, conductive plastic housing TTL compatible Standard 16-pin DIP footprint ST Receptacles
HCPL-M454 Ultra High CMR, Small Outline, 5 Lead, High Speed Optocoupler. Features
HCPL-M44 Ultra High CMR, Small Outline, Lead, High Speed Optocoupler Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe denotes a lead-free product Description
AC/DC to Logic Interface Optocouplers Technical Data
H AC/DC to Logic Interface Optocouplers Technical Data HCPL-37 HCPL-376 Features Standard (HCPL-37) and Low Input Current (HCPL-376) Versions AC or DC Input Programmable Sense Voltage Hysteresis Logic
HFBR-1505AZ/2505AZ (SMA
HFBR-0AZ/20AZ (SMA Tx/Rx for SERCOS) HFBR-BZ/2BZ (ST Tx/Rx for PROFIBUS) HFBR-0CZ/20CZ (SMA Tx/Rx for INTERBUS-S) Fiber Optic Transmitters and Receivers for SERCOS, PROFIBUS and INTERBUS-S Applications
FT01MHNG FT01MVNG. 530 nm DC-1 MBd RedLink Fiber Optic Transmitter Datasheet DESCRIPTION FEATURES APPLICATIONS AVAILABLE OPTIONS
FT01MHNG FT01MVNG 530 nm DC-1 MBd RedLink Fiber Optic Transmitter Datasheet DESCRIPTION The Firecomms DC to 1 MBd green 530 nm transmitter is designed for maximum distance at low speed communication in
SGM4809 Dual 158mW Headphone Amplifier with Active Low Shutdown Mode
Dual 58mW Headphone Amplifier GENERAL DESCRIPTION The SGM4809 is a dual audio power amplifier capable of delivering 58mW per channel of continuous average power with less than 0.% distortion(thd N)when
HOD /BBA HOD /BBA
FEATURES Full duplex over single fiber DC to 160 MHz link bandwidth Link budgets of 2 km [1.24 miles] or greater 40 db isolation Low profile ST housing Other options available VCSEL is Class 1 eye safe
1/2/4/8 GBPS 850NM VCSEL LC TOSA PACKAGES
DATA SHEET 1/2/4/8 GBPS 850NM VCSEL LC TOSA PACKAGES HFE7192-XXX FEATURES: LC TOSA HFE7192-x6x includes flex circuit LC TOSA HFE7192-x8x leaded package High performance VCSEL Low electrical parasitic TO
Current Transducer CTSR 1-P = 1A
Current Transducer CTSR 1-P I PRN = 1A For the electronic measurement of current: DC, AC, pulsed..., with galvanic isolation between the primary (high power) and the secondary circuit (electronic circuit).
AFBR-59E4APZ-LH. Multimode Small Form-Factor (SFF) Transceiver for Fast Ethernet, with LC Connector. Data Sheet. Features. Description.
Multimode Small Form-Factor (SFF) Transceiver for Fast Ethernet, with LC Connector Description The AFBR-59E4APZ-LH is a new power saving Small Form-Factor transceiver that gives the system designer a product
Data Sheet AFBR-2419MZ. 50 MBd Miniature Link Fiber Optic Receiver. Description. Features. Applications. AFBR-24x9xZ Available Part Numbers
AFBR-2x9xZ 0 MBd Miniature Link Fiber Optic Receiver Data Sheet Description The AFBR-2x9Z series components provide cost effective, high performance fiber optic communication links for information systems
200 ma Output Current High-Speed Amplifier AD8010
a FEATURES 2 ma of Output Current 9 Load SFDR 54 dbc @ MHz Differential Gain Error.4%, f = 4.43 MHz Differential Phase Error.6, f = 4.43 MHz Maintains Video Specifications Driving Eight Parallel 75 Loads.2%
AFBR-59E4APZ. Data Sheet. Multimode Small Form Factor (SFF) Transceiver for Fast Ethernet and FDDI, with LC Connector. Description.
Data Sheet AFBR-59E4APZ Multimode Small Form Factor (SFF) Transceiver for Fast Ethernet and FDDI, with LC Connector Description The AFBR-59E4APZ is a new power saving Small Form Factor transceiver that
AFBR-1555ARZ, AFBR-2555ARZ (SMA Tx/Rx for SERCOS)
Reinforced Metal Fiber Optic Transmitter and Receiver for SERCOS Applications Description SERCOS The Serial Realtime Communications System (SERCOS) is a standard digital interface for communication in
SGM MHz, 48μA, Rail-to-Rail I/O CMOS Operational Amplifier
PRODUCT DESCRIPTION The is a low cost, single rail-to-rail input and output voltage feedback amplifier. It has a wide input common mode voltage range and output voltage swing, and takes the minimum operating
SGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch
GENERAL DESCRIPTION The SGM44601 is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power
Nonreflective, Silicon SP4T Switch, 0.1 GHz to 6.0 GHz HMC7992
Nonreflective, Silicon SP4T Switch,.1 GHz to 6. GHz FEATURES Nonreflective, 5 Ω design High isolation: 45 db typical at 2 GHz Low insertion loss:.6 db at 2 GHz High power handling 33 dbm through path 27
Optically Coupled 20 ma Current Loop Receiver. Technical Data HCPL-4200
H Optically Coupled 2 ma Loop Receiver Technical Data OPTOCOUPLERS HCPL-42 Features Data Output Compatible with LSTTL, TTL and CMOS 2 K Baud Data Rate at 14 Metres Line Length Guaranteed Performance over
OBSOLETE. Ultrahigh Speed Window Comparator with Latch AD1317
a FEATURES Full Window Comparator 2.0 pf max Input Capacitance 9 V max Differential Input Voltage 2.5 ns Propagation Delays Low Dispersion Low Input Bias Current Independent Latch Function Input Inhibit
RoHS compliant 850 nm Multi-mode Transceiver (1000BASE-SX) 1 9, SC Duplex Connector, 3.3 V/5V Gbd Fiber Channel/1.25 Gigabit Ethernet
No Shield Forward Clipper Backward Clipper Features Compliant with IEEE 802.3z Gigabit Ethernet standard Compliant with Fiber Channel standard Industry standard 1 9 footprint SC duplex connector Single
2.1GHz. 2.1GHz 300nA RMS SFP OPTICAL RECEIVER IN+ MAX3748A IN- RSSI DISABLE LOS DS1858/DS1859 SFP. Maxim Integrated Products 1
19-2927; Rev 1; 8/03 RSSI (BW) 0.85pF 330nA 2mA P-P 2.7Gbps 2.1GHz +3.3V 93mW / 30-mil x 50-mil 580Ω TO-46 TO-56 MAX3748A Maxim RSSI MAX3748A DS1858/DS1859 SFP SFF-8472 2.7Gbps SFF/SFP (SFP) * 2.7Gbps
SGM ns, Low-Power, 3V/5V, Rail-to-Rail Input Single-Supply Comparator
150ns, Low-Power, 3V/5V, Rail-to-Rail GENERAL DESCRIPTION The is a single high-speed comparator optimized for systems powered from a 3V or 5V supply. The device features high-speed response, low-power
SGM9154 Single Channel, Video Filter Driver for HD (1080p)
PRODUCT DESCRIPTION The SGM9154 video filter is intended to replace passive LC filters and drivers with an integrated device. The 6th-order channel offers High Definition (HDp) filter. The SGM9154 may
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
Analog Devices Welcomes Hittite Microwave Corporation NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED www.analog.com www.hittite.com THIS PAGE INTENTIONALLY LEFT BLANK Typical Applications The HMC652LP2E
DATA SHEET. TDA4851 Horizontal and vertical deflection controller for VGA/XGA and autosync monitors INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET Horizontal and vertical deflection controller for VGA/XGA and autosync monitors File under Integrated Circuits, IC02 November 1992 FEATURES VGA operation fully implemented
SGM W Audio Power Amplifier
GENERAL DESCRIPTION The SGM489 is a.2w, fully integrated, audio power amplifier. It is designed to maximize audio performance in portable applications such as mobile phone. The portable application requires
Data Sheet AFBR-2418MZ. DC-50MBd Miniature Link Fiber Optic Receiver. Description. Features. Applications. AFBR-24x8xZ Available Part Numbers
AFBR-2xxZ DC-0MBd Miniature Link Fiber Optic Receiver Data Sheet Description The component is designed to provide cost effective, high performance fiber optic communication links for information systems
High Speed, G = +2, Low Cost, Triple Op Amp ADA4862-3
High Speed,, Low Cost, Triple Op Amp ADA4862-3 FEATURES Ideal for RGB/HD/SD video Supports 8i/72p resolution High speed 3 db bandwidth: 3 MHz Slew rate: 75 V/μs Settling time: 9 ns (.5%). db flatness:
HA MHz Video Buffer. Features. Applications. Ordering Information. Pinouts. Data Sheet February 6, 2006 FN2924.8
HA-533 Data Sheet February 6, 26 FN2924.8 25MHz Video Buffer The HA-533 is a unity gain monolithic IC designed for any application requiring a fast, wideband buffer. Featuring a bandwidth of 25MHz and
10 GBPS 1310NM PIN + PREAMP LC ROSA PACKAGE N LR-LC
Product Specification 10 GBPS 1310NM PIN + PREAMP LC ROSA PACKAGE PIN-1310-10LR-LC PRODUCT FEATURES LC ROSA PIN-1310-10LR-LC includes flex circuit High performance InGaAs PIN photodiode with separate transimpedance
Self-Contained Audio Preamplifier SSM2019
a FEATURES Excellent Noise Performance:. nv/ Hz or.5 db Noise Figure Ultra-low THD:
Positive Logic High CMR Intelligent Power Module and Gate Drive Interface Photocoupler
PHOTOCOUPLER Positive Logic High CMR Intelligent Power Module and Gate Drive Interface Photocoupler Description The fast speed photocoupler contains a AlGaAs LED and photo detector with built-in Schmitt
Dual Channel, High Speed Optocouplers Technical Data
Dual Channel, High Speed Optocouplers Technical Data HCPL-5 HCPL-5 HCPL-454 HCPL-5 HCPL-5 HCPL-54 Features 5 kv/µs Minimum Common Mode Transient Immunity at V CM = 5 V (HCPL-454/54) High Speed: Mb/s TTL
Features. = +25 C, Vdd = +5 Vdc, 50 Ohm System. trise, tfall (10/90% RF) ton, toff (50% CTL to 10/90% RF)
Typical Applications The HMC174MS8 / HMC174MS8E is ideal for: ISM Applications PCMCIA Wireless Cards Portable Wireless Features Ultra Small Package: MSOP8 High Third Order Intercept: +60 m Single Positive
RoHS compliant 1310 nm Single-mode Transceiver (1000BASE-LX) 2 5, LC Duplex Connector, 3.3 V Gbd Fiber Channel/1.25 Gigabit Ethernet
Features RoHS compliant Compliant with IEEE 802.3z Gigabit Ethernet standard Compliant with Fiber Channel standard Industry standard 2 5 footprint LC duplex connector Single power supply 3.3V Compatible
Data Sheet. Description. Features. Transmitter. Applications. Receiver. Package
AFBR-59F1Z 125MBd Compact 650 nm Transceiver for Data Communication over Polymer Optical Fiber (POF) cables with a bare fiber locking system Data Sheet Description The Avago Technologies AFBR-59F1Z transceiver
Features. Note: A 0.1 F bypass capacitor must be connected between pins Vcc and Ground. Specifications. Truth Table (Negative Logic)
ACPL-M483/P483/W483 Inverted Logic High CMR Intelligent Power Module and Gate Drive Interface Optocoupler Data Sheet Description The ACPL-M483/P483/W483 fast speed optocoupler contains a AlGaAs LED and
Voltage-to-Frequency and Frequency-to-Voltage Converter ADVFC32
a FEATURES High Linearity 0.01% max at 10 khz FS 0.05% max at 100 khz FS 0.2% max at 500 khz FS Output TTL/CMOS Compatible V/F or F/V Conversion 6 Decade Dynamic Range Voltage or Current Input Reliable
Four-Channel Sample-and-Hold Amplifier AD684
a FEATURES Four Matched Sample-and-Hold Amplifiers Independent Inputs, Outputs and Control Pins 500 ns Hold Mode Settling 1 s Maximum Acquisition Time to 0.01% Low Droop Rate: 0.01 V/ s Internal Hold Capacitors
High CMR Intelligent Power Module and Gate Drive Interface Optocoupler. Features. Specifications. Applications
ACPL-P80 and ACPL-W80 High CMR Intelligent Power Module and Gate Drive Interface Optocoupler Data Sheet Lead (Pb) Free RoHS fully compliant RoHS fully compliant options available; -xxxe denotes a lead-free
SGM9119 Triple, 5th-Order, Standard Definition Video Filter Driver
PRODUCT DESCRIPTION The SGM9119 is a low voltage, triple video amplifier with integrated reconstruction filters and input clamps. Specially suited for standard definition video signals, this device is
High Isolation, Silicon SP4T, Nonreflective Switch, 9 khz to 12.0 GHz ADRF5040
RF4 RF3 7 8 9 1 11 12 21 2 19 RF2 High Isolation, Silicon SP4T, Nonreflective Switch, 9 khz to 12. GHz ADRF54 FEATURES FUNCTIONAL BLOCK DIAGRAM Nonreflective 5 Ω design Positive control range: V to 3.3
AFBR-59F2Z Data Sheet Description Features Applications Transmitter Receiver Package
AFBR-59F2Z 2MBd Compact 6nm Transceiver for Data communication over Polymer Optical Fiber (POF) cables with a bare fiber locking system Data Sheet Description The Avago Technologies AFBR-59F2Z transceiver
Features. Applications OFF
HCPL Power Bipolar Transistor Base Drive Optocoupler Data Sheet Description The HCPL consists of a Silicondoped GaAs LED optically coupled to an integrated circuit with a power output stage. This optocoupler
ACPL-P480 and ACPL-W480
High CMR Intelligent Power Module and Gate Drive Interface Optocoupler Description The high-speed ACPL-P48/W48 optocoupler contains a GaAsP LED, a photo detector, and a Schmitt trigger that eliminates
SGM W Mono Fully Differential Audio Power Amplifier
.3W Mono Fully Differential GENERAL DESCRIPTION The SGM4995 is a fully differential audio power amplifier that is designed for portable communication device applications and demanding applications in mobile
SGM7222 High Speed USB 2.0 (480Mbps) DPDT Analog Switch
GENERAL DESCRIPTION The SGM7222 is a high-speed, low-power double-pole/ double-throw (DPDT) analog switch that operates from a single 1.8V to 4.3V power supply. SGM7222 is designed for the switching of
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit.
Current Transducer N = 6, 15, 25, 5 A Ref: LESR 6-NP, LESR 15-NP, LESR 25-NP, LESR 5-NP For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the
SGM9119 Triple, 5th Order, Standard Definition Video Filter Driver
PRODUCT DESCRIPTION The SGM9119 is a low-voltage, triple video amplifier with integrated reconstruction filter and input clamps. Specially suited for standard definition video signals, this device is ideal
PART MAX4144ESD MAX4146ESD. Typical Application Circuit. R t IN- IN+ TWISTED-PAIR-TO-COAX CABLE CONVERTER
9-47; Rev ; 9/9 EVALUATION KIT AVAILABLE General Description The / differential line receivers offer unparalleled high-speed performance. Utilizing a threeop-amp instrumentation amplifier architecture,
200 MHz Photoreceiver with Si PIN Photodiode
The picture shows the -FS with free space input. The photoreceiver will be delivered without post holder and post. Features Si PIN Detector, 0.8 mm Active Diameter Spectral Range 320... 1000 nm Bandwidth
DC to 3.5-GHz Amplified Photoreceivers Models 1591 & 1592
USER S GUIDE DC to 3.5-GHz Amplified Photoreceivers Models 1591 & 1592 These photoreceivers are sensitive to electrostatic discharges and could be permanently damaged if subjected even to small discharges.
= +25 C, With Vee = -5V & VCTL= 0/-5V
v.3.5db LSB GaAs MMIC 6-BIT DIGITAL Typical Applications Features The is ideal for: Basestation Infrastructure Fiber Optics & Broadband Telecom Microwave & VSAT Radios Military & Space Test Instrumentation
SGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch
GENERAL DESCRIPTION The SGM44601 is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power
1.5 GHz Ultrahigh Speed Op Amp AD8000
.5 GHz Ultrahigh Speed Op Amp AD8 FEATURES High speed.5 GHz, db bandwidth (G = +) 65 MHz, full power bandwidth (, VO = 2 V p-p) Slew rate: 4 V/µs.% settling time: 2 ns Excellent video specifications. db