Output Voltage Range. Max. Output Power

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "Output Voltage Range. Max. Output Power"

Transcription

1 EUD480SxxxDT Features Ultra High Efficiency (Up to 95%) Full Power at Wide Output Current Range (Constant Power) Thermal Sensing and Protection for LED Module 010V/PWM/Timer Dimmable (3 Timer Modes, Isolated design) DimtoOff with Standby Power 0.5 W Output Lumen Compensation Input Surge Protection: 6kV lineline, 10kV lineearth AllAround Protection: OVP, SCP, OTP Waterproof (IP67) and UL Dry / Damp / Wet Location SELV Output TYPE HL, for use in a Class I, Division 2 hazardous (Classified) location 7 Years Warranty Description The EUD480SxxxDT series is a 480W, constantcurrent, programmable LED driver that operates from Vac input with excellent power factor. Created for many lighting applications including high bay, high mast, aquaculture and sport, it provides a dimtooff mode with low standby power. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure troublefree operation, protection is provided against input surge, output over voltage, short circuit, and over temperature. Models Adjustable Output Current Range FullPower Current Range(1) Default Output Current A A 1.4A Input Voltage Range(2) A A 2.8 A 90~305Vac/ 127~300Vdc A A 4.2 A 90~305Vac/ 127~300Vdc A A 5.6 A 90~305Vac/ 127~300Vdc A A 10.0 A 90~305Vac/ 127~300Vdc Output Voltage Range Max. Output Power Typical Efficiency (3) Power Factor 120Vac 220Vac Model Number 90~305Vac/ 171 ~ 457Vdc 480W 95.0% EUD480S140DT 127~300Vdc 86 ~ 228Vdc 480 W 94.0% EUD480S280DT 57 ~ 152Vdc 480 W 94.5% EUD480S420DT 43 ~ 110Vdc 480 W 94.0% EUD480S560DT (4) 24 ~ 64Vdc 480 W 94.0% EUD480S10ADT (4) Notes: (1) Output current range with constant power at 480W (2) UL, FCC certified input voltage range: Vac or Vdc; otherwise: Vac or Vdc. (3) Measured at 100% load and 220Vac input (see below General Specifications for details). (4) SELV Output 1 / 15 Tel: Fax:

2 EUD480SxxxDT EUD480S140DT IV Operating Area EUD480S280DT EUD480S420DT EUD480S560DT EUD480S10ADT 2 / 15 Tel: Fax:

3 EUD480SxxxDT Input Specifications Input Voltage 90 Vac 305 Vac Vdc Input Frequency 47 Hz 63 Hz Leakage Current 0.75 MIU UL8750; 277Vac/ 60Hz 0.70 ma IEC605981; 240Vac/ 60Hz Input AC Current Inrush Current(I 2 t) 2.80A 2 s PF 0.90 THD 20% THD 10% Output Specifications 4.95 A Measured at 100% load and 120 Vac input A Measured at 100% load and 220 Vac input. At 220Vac input, 25 cold start, duration=5.56 ms, 10%Ipk10%Ipk. See Inrush Current Waveform for the details. At Vac, 5060Hz, 60%100% Load (288480W) At Vac, 5060Hz, 75%100% Load (360480W) Output Current Tolerance 5%Ioset 5%Ioset At 100% load condition Output Current Setting(Ioset) Range EUD480S140DT EUD480S280DT EUD480S420DT EUD480S560DT EUD480S10ADT Output Current Setting Range with Constant Power EUD480S140DT EUD480S280DT EUD480S420DT EUD480S560DT EUD480S10ADT Total Output Current Ripple (pkpk) Output Current Ripple at < 200 Hz (pkpk) 105 ma 210 ma 315 ma 435 ma 750 ma 1050 ma 2100 ma 3150 ma 4350 ma 7500 ma 1400 ma 2800 ma 4200 ma 5600 ma ma 1400 ma 2800 ma 4200 ma 5600 ma ma 5%Iomax 10%Iomax At 100% load condition, 20 MHz BW 2%Iomax At 100% load condition. Only this component of ripple is associated with visible flicker. Startup Overshoot Current 10%Iomax At 100% load condition No Load Output Voltage EUD480S140DT EUD480S280DT EUD480S420DT EUD480S560DT EUD480S10ADT 500Vdc 280Vdc 190Vdc 120Vdc 80Vdc Line Regulation ±0.5% Measured at 100% load Load Regulation ±1.5% 3 / 15 Tel: Fax:

4 EUD480SxxxDT Output Specifications (Continued) Turnon Delay Time Temperature Coefficient of Ioset 1.0 s 0.5 s 12V Auxiliary Output Voltage 10.8 V 12 V 13.2 V 12V Auxiliary Output Source Current Measured at 120Vac input, 60%100% Load Measured at 220Vac input, 60%100% Load 0.03%/ C Case temperature = 0 C ~Tc max 0 ma 200 ma Return terminal is Dim Note: All specifications are typical at 25 C unless otherwise stated. General Specifications Efficiency at 120 Vac input: EUD480S140DT Io= 1050 ma Io= 1400 ma EUD480S280DT Io= 2100 ma Io= 2800 ma EUD480S420DT Io= 3150 ma Io= 4200 ma EUD480S560DT Io= 4350 ma Io= 5600 ma EUD480S10ADT Io= 7500 ma Io= ma Efficiency at 220 Vac input: EUD480S140DT Io= 1050 ma Io= 1400 ma EUD480S280DT Io= 2100 ma Io= 2800 ma EUD480S420DT Io= 3150 ma Io= 4200 ma EUD480S560DT Io= 4350 ma Io= 5600 ma EUD480S10ADT Io= 7500 ma Io= ma 90.5% 89.5% 90.0% 88.5% 90.5% 89.0% 90.0% 89.0% 90.0% 89.0% 93.0% 90.5% 91.5% 90.5% 95.0% 94.0% 94.0% 93.0% 94.5% 93.0% 94.0% 93.0% 94.0% Measured at 100% load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Measured at 100% load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) 4 / 15 Tel: Fax:

5 EUD480SxxxDT General Specifications (Continued) Efficiency at 277 Vac input: EUD480S140DT Io= 1050 ma Io= 1400 ma EUD480S280DT Io= 2100 ma Io= 2800 ma EUD480S420DT Io= 3150 ma Io= 4200 ma EUD480S560DT Io= 4350 ma Io= 5600 ma EUD480S10ADT Io= 7500 ma Io= ma 93.5% 91.5% 95.5% 94.5% 94.5% 93.0% 94.5% 93.0% 94.5% 93.5% 94.0% 93.0% Measured at 100% load and steadystate temperature in 25 C ambient; (Efficiency will be about 2.0% lower if measured immediately after startup.) Standby power 0.5 W Measured at 230Vac/50Hz; Dimming off MTBF Lifetime Operating Case Temperature for Safety Tc_s Operating Case Temperature for Warranty Tc_w 216,000 Hours 91,000 Hours 40 C +85 C 40 C +75 C Measured at 220Vac input, 80%Load and 25 C ambient temperature (MILHDBK 217F) Measured at 220Vac input, 80%Load and 70 C case temperature; See lifetime vs. Tc curve for the details Case temperature for 7 years warranty. Please see Inventronics Warranty Statement for complete details. Storage Temperature 40 C +85 C Humidity: 5%RH to 100%RH Dimensions Inches (L W H) Millimeters (L W H) Net Weight 2650 g Note: All specifications are typical at 25 C unless otherwise stated. Dimming Specifications With mounting ear Absolute Maximum Voltage on the Vdim (+) Pin 20 V 20 V Source Current on Vdim (+)Pin 200 ua 300 ua 450 ua Vdim(+) = 0 V Dimming Output Range EUD480S140DT EUD480S280DT EUD480S420DT EUD480S560DT EUD480S10ADT EUD480S140DT EUD480S280DT EUD480S420DT EUD480S560DT EUD480S10ADT 10%Ioset Ioset 105 ma 210 ma 315 ma 435 ma 750 ma Ioset 1050mA Ioset 1400mA 2100mA Ioset 2800mA 3150mA Ioset 4200mA 4350mA Ioset 5600mA 7500mA Ioset 10000mA 105mA Ioset < 1050mA 210mA Ioset < 2100mA 315mA Ioset < 3150mA 435mA Ioset < 4350mA 750mA Ioset < 7500mA 5 / 15 Tel: Fax:

6 EUD480SxxxDT Dimming Specifications (Continued) Recommended Dimming Input Range 0 V 10 V Dim off Voltage 0.35 V 0.5 V 0.65 V Dim on Voltage 0.55 V 0.7 V 0.85 V Default 010V dimming mode. Hysteresis 0.2 V PWM_in High Level 3 V 10 V PWM_in Low Level 0.3 V 0.6 V PWM_in Frequency Range 200 Hz 3 KHz PWM_in Duty Cycle 1% 99% PWM Dimming off (Positive Logic) 3% 5% 8% PWM Dimming on (Positive Logic) 5% 7% 10% PWM Dimming off ( Negative Logic) 92% 95% 97% PWM Dimming on ( Negative Logic) 90% 93% 95% Hysteresis 2% Dimming mode set to PWM in PC interface. Note: All specifications are typical at 25 C unless stated otherwise. Safety &EMC Compliance Safety Category Standard UL/CUL UL8750,CAN/CSAC22.2 No CE EN , EN EMI Standards EN (1) EN EN FCC Part 15 (1) EMS Standards EN EN EN Notes Conducted emission Test &Radiated emission Test Harmonic current emissions Voltage fluctuations & flicker ANSI C63.4 Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference, and [2] this device must accept any interference received, including interference that may cause undesired Operation. Notes Electrostatic Discharge (ESD): 8 kv air discharge, 4 kv contact discharge RadioFrequency Electromagnetic Field Susceptibility TestRS Electrical Fast Transient / BurstEFT EN Surge Immunity Test: AC Power Line: line to line 6 kv, line to earth 10 kv (2) 6 / 15 Tel: Fax:

7 EUD480SxxxDT Safety &EMC Compliance (Continued) EMS Standards Notes EN EN EN EN Conducted Radio Frequency Disturbances TestCS Power Frequency Magnetic Field Test Voltage Dips Electromagnetic Immunity Requirements Applies To Lighting Equipment Note: (1) This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself. (2) To perform electric strength (hipot) testing, the GDT ground disconnect (nut and metal lock sheet) on the driver endcap should be removed temporarily to prevent the internal gas discharge tube from conducting (as allowed by IEC Clause 10.2). After testing is completed, these items must be reinstalled to restore linetoearth surge protection and secure the end cap. Derating Lifetime vs. Case Temperature 7 / 15 Tel: Fax:

8 EUD480SxxxDT Inrush Current Waveform Efficiency vs. Load EUD480S140DT(Io=1050mA) EUD480S140DT(Io=1400mA) EUD480S280DT(Io=2100mA) EUD480S280DT(Io=2800mA) 8 / 15 Tel: Fax:

9 EUD480SxxxDT EUD480S420DT(Io=3150mA) EUD480S420DT(Io=4200mA) EUD480S560DT(Io=4350mA) EUD480S560DT(Io=5600mA) EUD480S10ADT(Io=7500mA) EUD480S10ADT(Io=10000mA) 9 / 15 Tel: Fax:

10 EUD480SxxxDT Power Factor Total Harmonic Distortion Protection Functions External Thermal Protection NTC R kohm R kohm Protection Current Floor When R_NTC falls below R1, External Thermal Protection is triggered, reducing output current until R2 is reached. When R_NTC is less than R2, output current is reduced to the programmed Protection Current Floor. 10%Ioset 60%Ioset 100%Ioset 10%Ioset>Iomin (default setting is 60%) Iomin 60%Ioset 100%Ioset 10%Ioset Iomin (default setting is 60%) Over Temperature Protection Short Circuit Protection Over Voltage Protection Decreases output current, returning to normal after over temperature is removed. Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed. Limits output voltage at no load and in case the normal voltage limit fails. 10 / 15 Tel: Fax:

11 EUD480SxxxDT Dimming 010V Dimming The recommended implementation of the dimming control is provided below. Implementation 1: DC Input Notes: 1. The dimmer can also be replaced by an active 010V voltage source signal or passive components like resistors and zener. 2. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly. 3. If 010V dimming is not used, Dim + should be open. PWM Dimming The recommended implementation of the dimming control is provided below. Implementation 2: Positive logic 11 / 15 Tel: Fax:

12 EUD480SxxxDT Implementation 3: Negative logic Notes: 1. Do NOT connect Dim to the output V or V+, otherwise the driver will not work properly. 2. If PWM dimming is not used, Dim + should be open. 3. When PWM negative logic dimming mode and Dim+ is open, the driver will output minimum current. Time Dimming Time dimming control includes 3 kinds of modes, they are Self AdaptingMidnight, Self Adapting Percentage and Traditional Timer. Self AdaptingMidnight: Automatically adjusts the dimming curve based on the ontime of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time. Self AdaptingPercentage: Automatically adjusts the ontime of each step by a constant percentage = (actual ontime for the past 2 days if difference <15 min) / (programmed ontime from the dimming curve). Traditional Timer: Follows the programmed timing curve after power on with no changes. Output Lumen Compensation Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation. 12 / 15 Tel: Fax:

13 EUD480SxxxDT Programming Connection Diagram Note: The driver does not need to be powered on during the programming process. Please refer to PRGMUL2 MultiProgrammer datasheet for details. Mechanical Outline EUD480S140DT INPUT(UL SJTW 3*18AWG 7.8) OUTPUT(UL STW 2*18AWG 8.9) Tc V+ (RED) V (BLUE) AC/L (BLACK) AC/N (WHITE) GND (GREEN) GRAY PURPLE BLACK/WHITE BLUE/WHITE PINK DIMMING WIRE (UL *22AWG 5.8) PROJ: Unspecified toleranc:±1 13 / 15 Tel: Fax:

14 EUD480SxxxDT Others Models INPUT(UL SJTW 3*18AWG 7.8) OUTPUT(UL SJTW 2*14AWG 8.8) Tc V+ (RED) V (BLUE) AC/L (BLACK) AC/N (WHITE) GND (GREEN) GRAY PURPLE BLACK/WHITE BLUE/WHITE PINK DIMMING WIRE (UL *22AWG 5.8) PROJ: Unspecified toleranc:±1 RoHS Compliance Our products comply with the European Directive 2011/65/EC, calling for the elimination of lead and other hazardous substances from electronic products. 14 / 15 Tel: Fax:

15 EUD480SxxxDT Revision History Change Date Rev. Description of Change Item From To A Datasheets Release / / 15 / 15 Tel: Fax: