D Non-isolated driver chip fluorescent Description. Features. Application. 1 Power Mos Microelectronic Limited

Transcription

1 Non-isolated driver chip fluorescent Description The D80210 is a monolithic PWM high-efficiency LED driver control IC. It allows efficient operation of High Brightness (HB) LEDs from voltage sources ranging from 8VDC up to 550VDC. The D80210 controls an external NMOSFET at fixed switching frequency up to 500kHz.The frequency can be programmed by a single resistor. The LED string is driven at constant current to provide constant light output and enhanced reliability. The LED drive current can be programmed by a single resistor at CS pin to set the drive current from a few milliamps up to a preset high drive current.. Features 8V to 550V input range >90% Efficiency Constant-Current LED Driver LED driver current from a few ma to preset High current Drive Linear Dimming via ADJ pin PWM Dimming via PWM pin LED string from one to hundreds of Diodes Input Voltage Surge ratings up to 550V Application MR16 LED lighting Automotive Out door LED lighting Linear dimming can be achieved through input a 0V to 250mV DC voltage to ADJ pin. By grounding the PWM pin the chip can be disabled and draw less than 1mA current. 1 Power Mos Microelectronic Limited

2 Typical Application Marking Information & Pin Assignments (Top View) Pin Pin Name Description 1 V IN Input voltage 8V to 550V DC, 2 CS Senses LED string current 3 GND Device ground 4 Drive Drives the gate of the external NMOSFET 5 PWM Low Frequency PWM Dimming pin, also as Enable input. Internal 100kΩ resistor pull-down to GND 6 V DD Internally regulated supply voltage with 7.5V nominal value. A 1uF storage capacitor is used to provide storage when the rectified AC input is near the zero crossings. 7 ADJ Linear Dimming by changing the current limit threshold at current sense comparator. 8 R osc Oscillator control. A resistor connected between this pin and ground sets the PWM frequency. 2 Power Mos Microelectronic Limited

3 Absolute Maximum Ratings Vin Voltage 550V VDD Voltage 13V Operating Junction Temperature Range -40 to 125 Storage Temperature Range -55 to 150 Package Thermal Resistance, SOP-8, θja 165 /W Power dissipation (PD),TA = 25 C, SOP-8 757mW Package Thermal Resistance, DIP8, θja 95 /W Power dissipation (PD),TA = 25 C, DIP W Lead Temperature (Soldering,5 sec) 260 Note a: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Description Symbol Conditions Min Typ Max Units Input DC supply voltage range Shut-Down mode supply current Internally regulated voltage V INDC DC input voltage, fosc=25khz, V I INsd Pin PWM to GND, V IN = 8V 0,5 1,0 ma V DD V IN =8 ~ 550V, fosc=25khz, I DD(ext) =0, pin Drive open V Maximal pin VDD voltage V DDmax When an external voltage applied to pin V DD 13.5 V VDD current available for external circuitry 1 I DD(ext) V IN = 8V 1.0 ma VDD under voltage lockout threshold VDD under voltage lockout hysteresis UVLO V IN rising V ΔUVLO V IN falling 500 mv Pin PWM input low voltage V EN(lo) V IN = 8 ~ 550V 1.0 V Pin PWM input high voltage V EN(hi) V IN =8 ~ 550V 2.4 V Pin PWM pull-down resistance Current sense pull-in threshold voltage Drive high output voltage V DR(hi) I OUT = -20mA R LN V EN = 5V kω V T A = -40 C to +85 C mv Drive low output voltage V DR(lo) I OUT = 20mA V VDD -0.2 VDD V Rosc = 1.00МΩ Oscillator frequency fosc Rosc = 223 kω khz Rosc = 32 kω Power Mos Microelectronic Limited

4 Maximum Oscillator PWM Duty Cycle Linear Dimming pin voltage range Current sense blanking interval D MAXht F PWMhf = 25kHz, at Drive, 100 % CS to GND V T A 85 C, V IN = 12V mv T BLANK V CS = 0.55V ADJ, V ADJ = V DD ns Delay from CS trip to Drive low t DELAY V IN = 12V, V ADJ = 0.15, V CS = 0 to 0.22V after T BLANK 200 ns Drive shot-circuit current I Driveso V Drive =0, V DD =7.5 V -30 ma Drive sinking current I Drivesi V Drive =7,5 V, V DD =7.5 V 30 ma * VIN at slow increase of an entrance voltage up to 550V (During 500 ms) Detailed Description The D80210 is a low cost solution of off-line buck, boost or buck boost converter controller chip design for driving HB LED stings or arrays. It can be operated from either AC line of DC voltage between 7.5V to 550V. A passive power factor correction circuit can be used as an option. The D80210 can drive up to hundreds of HB (High Brightness) LEDs. The LED arrays can be configured as a series/parallel connection. The D80210 regulates constant LED driving current ensures controlled brightness of the LEDs, and extends LED lifetime. The D80210 has a PWM pin function as Enable pin and allows PWM control of LED brightness. The ADJ pin in D80210 also can input a DC control voltage from 0V to 250mV to program LED drive current and achieve LED brightness control. D80210 includes an internal high-voltage linear regulator which powers all internal circuits. The VDD allows to serve as a bias supply to low voltage external circuits. LED Drive Operation The D80210 can control all types of converters, non-isolated or isolated, operating in discontinuous or continues conduction modes. When the Drive current activated the external power NMOSFET, the input energy stores in an inductor and depending on the converter type, may partially deliver the energy to the LEDs. The energy stores in the inductor is further deliver to the output during the off-cycle of the power NMOSFET and drives the current to the string of LEDs. When VDD pin voltage exceeds the UVLO threshold the Drive pin is enabled. The drive current is controlled by means of limiting peak current in the external NMOSFET. A current sense resistor connected in series with the source node of the NMOSFET. The voltage across the sense resistor is feedback to the CS pin. When the CS pin voltage over 250mV threshold the power NMOSFET turn off. It can applying the DC voltage of 0V to 250mV to the ADJ pin to program the LED current as well. An external Capacitor can be connected to the ADJ pin when soft start is required. Setting LED Current For example if the peak-to-peak ripple current in the inductor is 150mA to get a 700mA LED current, the sense resistor should be calculated as 250mV/ (700mA+0.5x150mA) = 0.32Ω. 4 Power Mos Microelectronic Limited

5 Dimming By input 0V to 250mV DC voltage to ADJ pin to change the current or switching the current on and off while maintaining the constant current drive. When Voltage is higher than 250 mv will not change the output current. Or control the LED brightness by varying the duty of the output drive current through a PWM signal input to the PWM pin. Operating Frequency The operating frequency of the internal oscillator can be programmed between 20kHz to 500kHz. Fosc = 25000/(Rosc(kΩ)+22) khz Inductor Design The inductor for the application can be calculated from the desired peak-to-peak LED ripple current. The ripple current is selected to be 30% of the nominal LED current. For instance, the nominal current is 500mA. Then next step is estimate the total voltage drop across the LED string. In case of total 5 HB LEDs and each diode has a forward voltage drop of 3.0V at its nominal current. The total LED voltage is 15V. The nominal rectified input voltage Vin=120V X 1.41 = 169V, the switching duty ratio can be calculated as: D = V LEDS / Vin = 15/169 = Then, select the switching frequency as 200kHz, the required on-time of the MOSFET can be calculated: Ton = D / fosc = us The required inductor value calculate as below L = (Vin V LEDS ) X Ton / (0.3 x I LED ) = 455uH Input Bulk Capacitor Design An input filter capacitor should be designed to hold the rectified AC voltage above twice the LED string voltage within AC line cycle. Assuming 15% relative voltage ripple across the capacitor, the following formula to design the minimum value of the bulk input capacitor Cmin = I LED X V LEDS X 0.06 / Vin^2 Cmin = 16uF, a value of 16 uf /250V can be selected. Output Open circuit Protection In buck topology design, the LEDs are connected in series with the inductor. It is no need for any protection against an open circuit condition in the LED string. In contrast, the design of buck-boost or the Fly back topology the D80210 may cause excessive voltage stress of the NMOSFET and rectifier diode and have potential failure. In this kind of application, the D80210 can be disabled by pulling PWM pin to ground in case of over voltage condition detected. 5 Power Mos Microelectronic Limited

6 Enable The D80210 can be turned off by pulling the PWM pin to ground and draws quiescent current less than 1mA. Buck Converter Operation When the LED string voltage is lower than the input supply voltage the buck conversion topology can be used. However, the input voltage must be maintained higher than 2 times the forward voltage drop across the LEDs. This limitation is related to the output current instability that may happen when the D80210 buck converter operates at a duty cycle greater than 0.5. This instability reveals itself as an oscillation of the output current at a sub-harmonic of the switching frequency. Fly back (Buck-Boost) Design When the forward voltage drop of the LED string is higher, equal or lower than the input supply voltage the Buck-Boost topology can be designed. For instance, for automotive battery (12V) supply and output string consists of three to six HB LEDs for tail signal or car s interior lights application. In the Buck-Boost converter, the energy from the input source is first stored in the inductor when the switching MOSFET is On. The energy is the delivered to the output during the Off time of the MOSFET. When the energy stored in the Fly back inductor does not fully deleted by the next switching cycle (continuous conduction mode) the DC conversion between input and output voltage is express as ; Vout = - Vin x D / (1-D) The output voltage can be either higher or lower than the input voltage depending on the duty ratio. Take an automotive LED driver example which needs to drive three HB LEDs at 500mA. The automotive nominal input voltage Vin=12V, then the nominal duty ratio can be determined as D = V LEDS / (Vin + V LEDS ) = 9 / (12+9)=0.43 Then set the switching frequency as 50KHz. The MOSFET on time can be calculate as The inductor value is Ton = D / Fosc = 8.6 us L = Vin xton/(0.3 x I LED )=0.688mH Output Capacitor The buck-boost converter needs an output filter capacitor to deliver power to the LED string during MOSFET On time, when the Fly back inductor current is diverted from the output of the converter. For the purpose of average the current in the LED, a capacitor must present impedance to the switching output AC ripple current that is much lower than the dynamic impedance Rout of the LED string. If assume Rout=3Ω In the example, in order to attenuate the switching ripple by a factor of 10, a capacitor with equivalent series (ESR) of 0.3Ω is needed. A chip SMT tantalum capacitor can be selected for this application. 6 Power Mos Microelectronic Limited

7 Application Circuit 7 Power Mos Microelectronic Limited

8 8 Power Mos Microelectronic Limited

9 PACKAGE SOP-8 Package Outline Dimension DIP-8 Package Outline Dimension 9 Power Mos Microelectronic Limited

10 日期 Date 版本 Version 说明 Description 制作人 producer 工程师 Engineer 状态 Status A2 W A3 E 10 Power Mos Microelectronic Limited