MITSUBISHI (OPTICAL DEVICES) MF-2500STA-xxxxx MF-2500SRA-xxxxx MF-2500SRB-xxxxx SONET / SDH TRANSMITTER / RECEIVER MODULE
|
|
- Martha Dorsey
- 5 years ago
- Views:
Transcription
1 DESCRIPTION This product is designed to provide high optical performance for SDH STM-16/SONET OC-48. Transmitter uses uncooled laser module with drivered by specific integrated circuit. Receiver uses PD or APD pre-amp module and integrated circuits for re-shaping, re-timing and re-generating optical signal. FEATURES Full SONET/SDH line up Low cost Compact, low power +5V single power supply DC/DC converter built in for Rx Case Temperature Range: Class 1;-5 to +75deg.C Class 2;-40 to +85deg.C Clock recovery Multi Source Agreement FEC Rate 2.666Gb/s optional APPLICATION Short haul and long haul digital optical communication systems for SDH STM-16 / SONET OC-48. STM-16 : S-16.1, L-16.1, L-16.2, V-16.2 SONET : IR-1, LR-1, LR-2 MITSUBISHI (OPTICAL DEVICES) Absolute Maximum Ratings Stress below listed absolute maximum rating may cause permanent damage to the module. This is a stress only and functional operation of the module at these or any other conditions in excess of those given in the operational sections of this data sheet. Exposure to Absolute Maximum Rating for extended periods may affect module reliability. Supply voltage Tc=25deg.C. Parameters Symbol Ratings Unit Vcc +6.0 V Vee -6.0 V High output current - +/- 20 ma Input voltage 0 Vcc V Storage temperature Tstg -40 to +85 deg.c. Operating case temperature Tc class 1 : -5 to +75 class 2 : -40 to +85 deg.c. Soldering Temperature deg.c. Soldering Time - 10 sec Relative humidity(non condensation) - 10 to 80 % Fiber bend radius - 32 mm
2 MITSUBISHI (OPTICAL DEVICES) Block diagram LD Module VCC VCC :integrated device Driver IC PD LD OPT.OUT SELC DATAin DATAin CLOCKin CLOCKin Modulation Control Driver IC APC IC APC Transmitter Monitoring for back face current Monitoring for LD current Laser Degrade Alarm SDC OILV Monitor DATAout OPT.IN PD Decider DATAout CLKout Preamp CLKout PLL Alarm PD-Preamp Module Clock recovery IC S-16.1 / IR-1 Receiver Signal Detect OILV OPT.IN Monitor DC/DC APD Control APD Amp Decider DATAout DATAout CLKout Preamp CLKout Alarm PLL APD-Preamp Module AGC amp Clock recovery IC Signal Detect DTV L16.1 / LR-1, L16.2 / LR-2,V-16.2 Receiver
3 Electrical characteristics All parameters are specified over the operating case temperature. Measurement conditions are at Mb/s +/-20ppm, NRZ PN and 50% duty cycle data signal. Vcc=+5.0V+/-5% Mb/s is optional. The parameters with * mark should be specified separately. Temperature range : class1 : -5deg.C. to +75deg.C, class2 : -40deg.C. to +85deg.C. Transmitter Parameters Condition Symbol Min. Typ. Max. Unit Supply voltage note V Power consumption total W *Input sensitivity data and clock voltage note 2,3 SV Vpp Input data and clock phase NOTE7 Tdi ps Shut Down Command (SDC) activation time ms SDC de-activation time ms Normalized back face voltage note mv Back face voltage accuracy % Monitor bias voltage note mv/ma Monitor bias voltage accuracy % Logic input High level note 4 Vih Vcc - Logic input Low level note 4 Vil Logic output High level (LDA de-activate) note 4 Voh Vcc - Logic output Low level (LDA activate) note 4 Vol note : Vcc-Vee ; with Vcc at +5V Vee must be at 0V note : Internally AC coupled with 50ohm internal termination note1 : Vcc-Vee ; with Vcc at +5V Vee must be at 0V If customer need to operate under 5.2V power supply,please contact MITSUBISHI. note2 : Internally AC coupled with 50ohm internal termination * note3 : This sensitivity is achieved by applying at minimum either a 0.5Vpp signal on one input while the other input is tied to ground or by applying two complementary 0.25Vpp signal on both inputs. note4 : when Vcc at +5V and Vee at 0V note5 : This voltage is measured taking Vee as reference. Receiver MITSUBISHI (OPTICAL DEVICES) Parameters Condition Symbol Min. Typ. Max. Unit Positive supply voltage note V Power consumption ( S-16.1 ) total W Power consumption ( Others ) total W *Output data and clock voltage single ended SV Vpp *Output data and clock voltage differential DV Vpp Output data and clock phase NOTE8 Tdo ps Output data and clock rise and fall time NOTE9 Tr / Tf ps *Jitter generation GR-253/ITU-T G783 Ulrms *Jitter tolerance GR-253/ITU-T G783 Ulpp *Jitter transfer peaking - GR-253/ITU-T G783 db Loss of Power Alarm (LPA) activation BER LPA de-activation BER LPA hysteresis - No chattering - LPA activation time ms LPA de-activation time ms Logic output High level (LPA activate) note 4 Voh Vcc - Logic output Low level (LPA de-activate) note 4 Vol note 6 : If customer need to operate under -5.2V power supply, please contact MITSUBISHI.
4 MITSUBISHI (OPTICAL DEVICES) Optical characteristics Mb/s is optional. The parameters with * mark should be specified separately. cond. symb. Min. Typ. Max. Min Typ. Max ITU-T/SONET - - S-16.1/IR-1 L-16.1/LR-1 - Optical budget note db Transmitter Center wavelength nm Optical source - - SLM SLM - Optical output power note9 S nom dbm Shutdown optical power - Sidle dbm Spectral width note nm SMSR db Extinction ratio note11 ER db Eye Opening - - ITU-T G.957 STM16 ITU-T G.957 STM16 - Dispersion ps/nm Output Jitter (12 khz to 20 MHz) UIrms Output Jitter (5 khz to 20 MHz) UIpp maximum return loss db Receiver *Receiver sensitivity note12 note13 R sen dbm *Receiver overload note14 R ovr dbm Path penalty db Maximum reflectance db cond. Symb. Min. Typ. Max. Min Typ. Max ITU-T/SONET - - L-16.2/LR-2 V Optical budget note db Transmitter Center wavelength nm Optical source - - SLM SLM - Optical output power note9 S nom dbm Shutdown optical power - Sidle dbm Spectral width note nm SMSR db Extinction ratio note11 ER db Eye Opening - - ITU-T G.957 STM16 ITU-T G.957 STM16 - Dispersion ps/nm Output Jitter (12 khz to 20 MHz) UIrms Output Jitter (5 khz to 20 MHz) UIpp maximum return loss db Receiver Receiver sensitivity note12 note13 R sen dbm Receiver overload note14 R ovr dbm Path penalty db Maximum reflectance db note8 : The V-16.2 version is adapted to standard 10dBm to 13dBm EDFA optical bandwidth. note9 : Measured at the connector interface. Provision of 0.5dB is taken for S point measurement. note10 : The maximum full width of the central wavelength peak, measured 20dB down from maximum amplitude under modulation condition PRBS note11 : Measured at the connector interface under modulation condition PRBS note12 : Measured at BER note13 : Provision of 0.5dB is taken for R point measurement if SMF fiber is used. note14 : The device must not be damaged when this optical power is applied to the optical input. The device is not meant to operate at such an optical input power. All min and max. parameters are specified End-of-Life within the overall relevant operating temperature range. The typical values are referenced to +25deg.C,nominal power supply, beginning of life.
5 MITSUBISHI (OPTICAL DEVICES) Ordering information Transmitter : MF-2500STA-XXXXX (*1) Receiver (PD) : MF-2500SRA-XXXXX (*2) (APD) : MF-2500SRB-XXXXX (*3) XXXXX (*1) XXXXX (*2) XXXXX (*3) ITU code Optical connector type Optical connector type Optical connector type FC SC FC SC FC SC S-16.1 / IR-1 class1 002VA 002WA 002VA 002WA S-16.1 / IR-1 class2 TBD TBD TBD TBD L-16.1 / LR-1 class1 003VA 003WA 002VA 002WA L-16.1 / LR-1 class2 TBD TBD TBD TBD L-16.2 / LR-2 class1 004VA 004WA 003VA 003WA L-16.2 / LR-2 class2 TBD TBD TBD TBD V-16.2 class1 009VA 009WA TBD TBD V-16.2 class2 TBD TBD TBD TBD Note : Mb/s is optional. Note : The parts number should be specified separately.
6 Pin Allocation Transmitter pin allocation No. Symbol Description No. Symbol Description 1 VEE Negative power supply 4) 24 VCC Positive power supply 4) 2 BACK(+) Monitoring for back facet PD current 23 GND Ground 3 BIAS(+) Monitoring for LD bias current 22 Cki- False clock input 4 SDC Shut Down Command 3) 21 GND Ground 5 SELC Clock mode select 2) 20 Cki+ True clock input 1) 6 GND Ground 19 GND Ground 7 TDEM 6) Temperature Deviation Error Monitor / /NIC No Internal Connection 18 Di- False data input 8 LDA Laser Degrade Alarm 5) 17 GND Ground 9 NUC No user connection 16 Di+ True data input 10 WSC 7) / NIC Wavelength Selection Command / No Internal Connection 15 GND Ground VTEC 6) TEC supply voltage / 11 GND Ground 14 /NIC No Internal Connection 12 VEE Negative power supply 4) 13 VCC Positive power supply 4) 1) : The falling edge of Cki+ clock input signal is at the Di+ data eye pattern crossing point. 2) : When open (or low) the module is in the operating mode. When high the module operates in non clocked mode. 3) : When open (or low) the module is in the operating mode. When high the module is in the shut down mode (no optical output power). 4) : Vcc-Vee; with Vcc at +5V Vee must be at 0V. 5) : When provided a digital alarm indicates that the laser is degraded. The active level is a low level. This pin must be teidto Vcc through a 100k ohm resistor when the digital alarm is not proved. 6) : Module with cooled LD and module for WDM only. 7) : Module for WDM only. Receiver pin allocation MITSUBISHI (OPTICAL DEVICES) No. Symbol Description No. Symbol Description 1 HV / NIC High Voltage 1) 24 NUC No user connection 2 NUC No user connection 23 OILV / NIC Optical Input Light Voltage 5) 3 LPA Loss of Power Alarm 3) 22 VCC Positive power supply 4 GND Ground 2) 21 NUC No user connection 5 Cko- False clock output 20 GND Ground 2) 6 Cko+ True clock output 6) 19 GND Ground 2) 7 GND Ground 2) 18 NIC/VEE Negative power supply 7) 8 VCC Positive power supply 17 GND Ground 2) 9 GND Ground 16 GND Ground 2) 10 Do+ True data output 15 GND Ground 2) 11 Do- False data output 14 GND Ground 2) 12 GND Ground 2) 13 DTV / NIC Decision Threshold Voltage 4) 1) : S-16.1 / IR-1 : NIC, L-16.1 / LR-1, L-16.2 / LR-2, V-16.2 : NIC 2) : Package is at same potential as GND. 3) : LPA output is a logic level that indicates the presence or absence of a sufficient optical input level. A logical high level indicates an input optical level too low. 4) : This pin is not internally connected if the amplitude decision threshold is not made adjustable. S-16.1 :NIC, L-16.1 /L-16.2/V-16.2 : TBD 5) : OILV function is optional. If customer requires OILV, please contact MITSUBISHI. This pin is not internally connected if the Optical Input Light Voltage functionality is not provided. 6) : The falling edge of Cko+ clock output signal is in the middle of Do+ data pattern. 7) : This pin is Not Internally Connected(NIC) as standard. This pin is reserved for in case of V= -5.2 V operation or future application.
7 General Outline Drawing NOTE : DIMENSIONS ARE IN MILLIMETERS NOTE : TOLERANCES UNLESS NOTED +/- 0.5 mm Transmitter MITSUBISHI (OPTICAL DEVICES) Note : This hole is used for testing by MITSUBISHI. Recommendation is that the pattern that is faced with this hole on customer board should be ground or no pattern. Note : This drawing is in case of FC connector.
8 MITSUBISHI (OPTICAL DEVICES) Receiver (S-16.1/IR-1) Note : This drawing is in case of FC connector. Receiver (L-16.1/LR-1,L-16.2/LR-2,V-16.2) Note This hole is used for testing by MITSUBISHI. Recommendation is that the pattern that is faced with this hole on customer board should be ground or no pattern. Note : This drawing is in case of FC connector.
9 MITSUBISHI (OPTICAL DEVICES) APPLICATION NOTES NOTE1 : Data / Clock Input interface Transmitter Di+ Di- 50Ω VBB AC Coupled Interface NOTE2 : Shut Down Command (SDC) interface Shut Down Command Optical output ON OFF Transmitter TTL SDC 100kΩ comparator NOTE3 Clock Select (SELC) interface SELC Clocked Clock mode Non-Clocked Transmitter TTL SELC 100kΩ comparator
10 NOTE4 : Laser bias / Laser back facet monitor interface LD Module MITSUBISHI (OPTICAL DEVICES) Laser back facet current monitor APC Laser bias current monitor NOTE5 : Data / Clock Output interface Output stage Data/ Clock Data/ Clock Output Output Coupling Capacitor 50Ω NOTE6 : Signal detect interface Customer logic reference Receiver ON OFF Optical Input Signal detect Signal detect TTL
11 NOTE7 : Transmitter Data / Clock Input Phase MITSUBISHI (OPTICAL DEVICES) Cki+ Tdi - + Di+ NOTE8 : Receiver Data / Clock Output Phase Cko+ Tdo - + Do+ T / 2 T NOTE9 : Receiver Data / Clock Output Rise / Fall Time 80% Cko+ / - 20% Tr Tf Do+ / - 80% 20% Tr Tf
12 MITSUBISHI (OPTICAL DEVICES) Typical performance S-16.1 Optical eye pattern (wide band) (Mask) S-16.1 Receiver sensitivity (back to back) Note MITSUBISHI ELECTRIC. reserves the right to make changes to the products or information contained herein without notice. Customer versions are available for large quantities. The end of document
Alcatel 1926 SDH STM-16 / OC-48 SDH / SONET integrated modules Compact High Power DWDM Transmitter. Description. Applications. Features.
Alcatel 1926 SDH STM-16 / OC-48 SDH / SONET integrated modules Compact High Power DWDM Transmitter Description These transmitters are intended to be used in Dense Wavelength Division Multiplexed (DWDM)
More informationXFP 10G 1550nm 120Km. Features. Description. Applications. Ordering information. APC XFP LC Transceiver XFP-10GFX15-D120
XFP 10G 1550nm 120Km Description APC 120km XFP Transceiver is designed for 10G SDH/SONET and 10G Fiber Channel applications. The transmitter section incorporates a cooled EML laser, and the receiver section
More information10Gbps XFP Optical Transceiver
10Gbps XFP Optical Transceiver RTXM226-405 Features Compliant with XFP MSA Data Rate from 9.95 Gbps to 11.3Gbps 1310nm DFB TOSA and PIN ROSA Industry-standard,protocol-indep endent,xfi interface Transmission
More informationSTX / SRX SONET/SDH Transmitters & Receivers. Parameter Symbol Minimum Maximum Units Storage Temperature T st C
OCP STX / SRX SONET/SDH Transmitters & Receivers Features! Fully compliant with SONET/SDH OC- to OC-24 (52 Mb/s, 56 Mb/s, 622 Mb/s &.25 Gb/s) specifications! Long Reach 30 (40 km distance), Long Reach
More informationPart Number Transmitter Output Power Receiver Sensitivity Reach Temp DDM RoHS
Product Features Compliant to ITU-T G.957 STM-16 S-16.1 Specifications according to SFF-8074i and SFF-8472, revision 9.5 Digital Diagnostic Monitoring available Uncooled 1310nm DFB Laser Up to 2.67Gb/s
More information70~80km CWDM XFP Optical Transceiver
70~80km CWDM XFP Optical Transceiver Features Wavelength selectable to ITU-T standards covering CWDM grid XFP MSA Rev 4.5 Compliant Data rate from 9.95Gbps to 11.1Gbps No Reference Clock required Cooled
More informationApplications: Description:
Features: Support multi protocol from 9.95Gb/s to 11.3Gb/s Hot pluggable 30 pin connector Compliant with XFP MSA Transmission distance of 80km over single mode fiber DWDM EML laser transmitter APD Receiver
More informationProduct Features. Applications. Descriptions. Ordering Information. Electrical Pin Description
Product Features Compliant with ITU-T G.691 STM-64 L-64.2 Compliant to IEEE Std 802.3-2005 10Gb Ethernet 10GBase-ZR/ZW XFP MSA Rev. 4.5 compliant Full digital diagnostic management interface XFP MSA package
More informationDWDM SFP 4.25Gb/s Transceiver 30Km Hot Pluggable, Duplex LC, 3.3v C Band 100-GHz DWDM DFB-LD PDSFP-96-1XX12-22F
DATASHEET FEATURES: Up to 4.25Gb/s Data Links Compliant with Small form Factor Pluggable MSA Specification C-Band ITU 100-GHz DWDM grid DFB with built-in Isolator Standard and Wide Operating Temperature
More informationXFP-10GB-EZR (OC192) 10GB Multirate DDMI XFP 1550nm cooled EML with APD Receiver 120km transmission distanc 10GB Multirate DDMI XFP
Feature XFP MSA Rev 4.5 compliant 120km Reach on SMF-28 fi ber utilizing Electronic Dispersion Compensation (EDC) Supports 9.95, 10.31, 10.52, 10.7 and 11.1Gb/s XFI High Speed Electrical Interface Digital
More informationParameter Symbol Min Max Unit Storage Temperature T ST Case Operating Tempature Tc Supply Voltage V CC V
Features: Support multi protocol from 9.95Gb/s to 11.3Gb/s Hot pluggable 30 pin connector Compliant with XFP MSA Transmission distance of 40km over Single mode fiber 1310nm DFB laser transmitter. Duplex
More informationSingle Mode 1X9 Dual ST Transceiver 155MBs 5V. Applications Fiberoptic communications systems Networking Digital and Analog Signal transmission
PD-. offers singlemode laser based fiber optic transceiver modules in convenient industry standard 1X9 style packages. The PTRX series modules are designed to comply with SONET/SDH standards for 155MBs
More informationSingle-mode 155Mbps 2X10 SFF Transceiver
Features LC duplex receptacle Standard 2 x 10 footprint 1310nm or 1550nm laser transmitter with automatic power control Laser bias and power monitor AC or DC coupled LPECL/PECL compatible data input and
More informationDTR-xxx-3.3-SM-T. 3.3 Volt Single Mode Transceivers (1x9 pin-out) ! Single +3.3 V supply & LV-PECL data interface. ! Eye Safe (Class I Laser Safety)
OCP Description DTR-xxx-3.3-SM-T 3.3 Volt Single Mode Transceivers (1x9 pin-out) The DTR-xxx-3.3-SM-T fiber optic transceivers are the 3.3V power supply versions of our standard DTR-xxx-SM fiber optic
More informationT S P - D x A K 6 - T 2 S
Specification 1x9 Form Factor Duplex ST Receptacle Optical Transceivers STM-1 / OC-3 / 100BASE 155Mbit/s Ordering Information T S P - D x A K 6 - T 2 S Temperature 1 : +0 ~ +70 2 : -40 ~ +85 Model Name
More informationGPON ONU SFF 2X10 GNUF-3412S-B2CDA
Features GPON ONU SFF 2X10 GNUF-3412S-B2CDA Single fiber Bi-Directional transceiver with SC Receptacle Connector 1310nm burst-mode 1.25Gbps transmitter with DFB LD laser 1490nm continuous-mode 2.5Gbps
More informationXFP DWDM 10G 80Km ZR SLXFD-10XX-ZR
XFP DWDM 10G 80Km ZR SLXFD-10XX-ZR Overview Sourcelight DWDM XFP Transceiver exhibits excellent wavelength stability, supporting operation at 100GHz channel, cost effective module. It is designed for 10G
More informationDTR-xxx-SM-LC & DTR-xxx-SM-LS. 3.3 Volt 2x5 LC connector OC-3 & OC-12 Single Mode Transceivers
OCP Description DTR-xxx-SM-LC & DTR-xxx-SM-LS 3.3 Volt 2x5 LC connector OC-3 & OC-2 Single Mode Transceivers The DTR-xxx-SM-LC and DTR-xxx-SM-LS fiber optic transceivers offer a simple, convenient way
More informationULTRAPAK 10 DWDM Optoelectronics Subsystem. General Description. Features. Applications. Figure 1. UltraPak 10 Subsystem
General Description The ULTRAPAK 10 DWDM is a highly integrated optoelectronics subsystem that includes a 10 Gbit/s External Modulated optical transmitter, a 10 Gbit/s PIN or APD optical receiver and a
More informationFeatures: Applications: Description:
Monolithic MZM Tunable TOSA APD Receiver Supports 50GHz ITU Grid C-Band with a wavelength locker Duplex LC connector Power supply voltages : +3.3V Temperature range 0 C to 70 C Power dissipation:
More informationProduct Specification OC-48 LR-2/STM L-16.2 Multirate 2x10 SFF Transceiver FTLF1621S1xCL
Product Specification OC-48 LR-2/STM L-16.2 Multirate 2x10 SFF Transceiver FTLF1621S1xCL PRODUCT FEATURES Up to 2.67Gb/s bi-directional data links Standard 2x10 pin SFF footprint (MSA compliant) Analog
More information3.3V / 1550 nm / 2.5 Gbps Digital Diagnostic SFP LC SINGLE-MODE TRANSCEIVER
/ SPS-9160BWG / SPS-9160AWG (RoHS Compliant).V / 10 nm /. Gbps Digital Diagnostic SFP LC SINGLE-MODE TRANSCEIVER **********************************************************************************************************************************************************************
More informationSONET OC-12/SDH STM-4 Transceiver RSP06Sxx, RSP06Mxx
RoHS Compliant SONET OC-12/SDH STM-4 Transceiver RSP06Sxx, RSP06Mxx Applications SONET OC-12 and OC-3 SR-1 SONET OC-12 and OC-3 IR-1 SONET OC-12 and OC-3 LR-1 SONET OC-12 and OC-3 LR-2 Features Up to 622Mb/s
More informationApplications: DWDM Networks SONET OC-192/SDH STM-64 10GBASE-ER/EW Ethernet 40km 10G Fiber Channel. Description:
Features: Support multi protocol from 9.95Gb/s to 11.3Gb/s Hot pluggable 30 pin connector Compliant with XFP MSA Transmission distance of 40km over single mode fiber DWDM EML laser transmitter 100GHz ITU
More informationApplications: Description:
Features: Support 9.95Gb/s to 11.32Gb/s bit rates. Hot pluggable XFP footprint Maximum link length of 100km Compliant with XFP MSA Temperature-stabilized DWDM rated EML transmitter 100GHz ITU Grid C Band
More informationSinglemode 155Mbps Optical Transceiver SFP with MSA
Features Compliant SFP MSA Compliant with GR-253-CORE SONET OC-3 and ITU-T G.957 SDH STM-1 specifications Metal case & LC duplex receptacle with bail de-latch Transmitter disable input and receiver loss
More informationMTX510E Series 10Gb/s 1550nm Electro-absorption Modulated Laser (EML) 14 Pin Package with G-S-G RF Input
10Gb/s 1550nm Electro-absorption Modulated Laser (EML) 14 Pin Package with G-S-G RF Input The MTX510E series contain an electro-absorption modulated laser (EML) module consists of a multiquantum-well DFB
More informationSFP BIDI 2.5Gbps 40Km Tx1310/Rx1550nm / Tx1550/Rx1310nm
SFP BIDI 2.5Gbps 40Km Tx1310/Rx1550nm / Tx1550/Rx1310nm XSLB-25XXL-40X-D Overview The XSLB-25XXL-40X-D are small form factor pluggable module for OC-48 / STM-16 and Fiber Channel single fiber communications
More informationXFP-10GZR-OC192LR 80KM XFP Optical Transceiver
XFP-10GZR-OC192LR 80KM XFP Optical Transceiver Features XFP MSA Compliant data rate from 9.95 Gbps to 11.1Gbps No Reference Clock required Cold Start up Wavelength Compliance EML transmitter and APD receiver
More informationXFP-10GER-192IR V Operating Environment Supply Voltage 1.8V V CC V Operating Environment Supply Current 1.8V I CC1.
XFP-10GER-192IR The XFP-10GER-192IRis programmed to be fully compatible and functional with all intended CISCO switching devices. This XFP optical transceiver is designed for IEEE 802.3ae 10GBASE-ER, 10GBASE-
More informationGIGALIGHT 80km DWDM XFP Optical Transceiver GXD-XX192-08C
GIGALIGHT 80km DWDM XFP Optical Transceiver GXD-XX192-08C Features Wavelength selectable to C-band ITU-T grid wavelengths Suitable for use in 100GHz channel spacing DWDM systems XFP MSA Rev 4.5 Compliant
More informationUK - SFP MONOMODO 20 KM 1310 NM. DTS3112L - C(D)
Description Datocom 1 DTS3112L-C(D)20 optical transceivers are designed for GE/1 x FC optical interface for data communications with single mode fiber (SMF), and multimode fiber (MMF) as well. They operate
More informationXFP DWDM 10G 40Km ER SLXFD-10XX-ER
XFP DWDM 10G 40Km ER SLXFD-10XX-ER Overview Sourcelight DWDM XFP Transceiver exhibits excellent wavelength stability, supporting operation at 100 GHz channel, cost effective module. It is designed for
More informationGDETP-XX21S-2CD DWDM EPON OLT SFP Transceiver
Features GDETP-XX21S-2CD DWDM EPON OLT SFP Transceiver Dual Fiber Transceiver with single mode LC receptacle Wavelength selectable to C-band and L-band ITU-T grid wavelengths Suitable for use in 100GHz
More informationOC-48 LR-2/STM L-16.2 RoHS Compliant Pluggable SFP Transceiver
OC-48 LR-2/STM L-16.2 RoHS Compliant Pluggable SFP Transceiver PRODUCT FEATURES Up to 2.67Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions Uncooled 1550nm
More informationFSPC-xx12-40D. 1.25G SFP CWDM 1470nm~1610nm 40km Optical Transceiver
FSPC-xx12-40D 1.25G SFP CWDM 1470nm~1610nm 40km Optical Transceiver Features Compliant with SFP MSA and SFF-8742 Dual LC connector receptacle Center wavelength: 1470nm~1610nm CWDM Laser diode transmitter
More informationPRE-SFP-OC Mb/s Transceiver, 1310 nm, 15 km (IR1), DDM
Product Features Up to 155 Mb/s Data Links Hot-Pluggable 1310nm FP laser transmitter Duplex LC connector RoHS compliant and Lead Free Up to 20 km on 9/125 µm SMF Single +3.3V Power Supply Low power dissipation,
More informationLEG. 10Gbps SFP+ Transceiver
430-4585-LEG DELL 10GBASE-ER SFP+ SMF 1550NM 40KM REACH LC DOM 430-4585-LEG 10Gbps SFP+ Transceiver Features Duplex LC connector Support hot-pluggable Metal with lower EMI Excellent ESD protection RoHS
More informationKRN-SF-SM GD 10G SFP+ ER
KRN-SF-SM-040-10GD 10G SFP+ ER 1310nm 40KM SMF LC DDM Optical Transceiver Module (10GBASE-ER Transceiver) Features: 1550nm EML Transmitter Distance up to 40km over SMF Single 3.3V Power supply and LVTTL
More informationDS10-F007. Datasheet. Initial Date R&D Dept. GH Zheng. OE OFD6xx418 Written Team. PN OFD6xx418 Description XFP, DWDM 80KM
No. Initial Date 2012-07-29 OE Written Team R&D Dept. GH Zheng Ⅰ Preview PN Description XFP, DWDM 80KM Ⅱ Contents 1. Features 2. Applications 3. Description 4. Absolute maximum Ratings 5. Operating Environment
More information10Gb/s 10Km CDR SFP+ 1310nm Transceivers
Features l Compliant to SFP+ MSA l Fully RoHS Compliant l All metal housing for superior EMI performance l IPF compliant mechanics (SFF-8432 Rev 5.0) l CDR with 9.95 to 11.3Gbps l Uncooled DML DFB Laser
More informationX2-10GB-Cxx-ER CWDM X2-10GBASE, 40km Reach
X2-10GB-Cxx-ER CWDM X2-10GBASE, 40km Reach Features Wavelength selectable to ITU-T standards covering CWDM grid Compatible with X2 MSA Rev2.0b Support of IEEE 802.3ae 10GBASE-ER at 10.3125Gbps Transmission
More informationPRE-SFP-OC Gb/s Transceiver, 1310 nm, 15 km (IR1), DDM
Product Features Up to 2.67Gb/s Data Links Hot-Pluggable 1310nm DFB laser transmitter and PIN receiver Duplex LC connector RoHS compliant and Lead Free Up to 15 km on 9/125 µm SMF Single +3.3V Power Supply
More informationProduct Features. Applications. Standards Compliance. 10G SFP+ LR Transceiver. General Description
General Description Accelight ASP10I-LR is designed for use in 10 Gb/s links over single mode fibers(smf). It is compliant with the SFP+ MSA and industry standard SFF-8472. The module incorporates a 1310nm
More informationFeatures. Ordering Information
Features RoHS compliant Compatible with 155 Mbps ATM and SONET OC-3 SDH STM-1 Industry standard 1 9 footprint SC connector Single power supply 3.3 V Differential PECL inputs and outputs Class 1 laser product
More informationTRPUFEALXx000E1G Fast Ethernet 100BASE-LX10 SFP Single Mode Transceivers With Digital Diagnostics
Features Compliant with IEEE 802.3ah/D3.3 (100BASE-LX10) Compatible with SFP MSA RoHS6/6 Compliant Digital Diagnostics through Serial Interface External Calibration for Digital Diagnostics 1310nm Fabry
More informationEMPOWERFIBER 80km DWDM XFP Optical Transceiver EXD-XX192-08C
EMPOWERFIBER 80km DWDM XFP Optical Transceiver EXD-XX192-08C Features Wavelength selectable to C-band ITU-T grid wavelengths Suitable for use in 100GHz channel spacing DWDM systems XFP MSA Rev 4.5 Compliant
More informationXTS31U-10Lx. 10 G Ethernet 10 km SFP+ Transceiver 10GBASE-LR/10GBASE-LW. XTS31U-10Lx 10 G 10 km SFP+ Transceiver. Applications.
Applications 10G Ethernet 10GBASE-LR/LW 10G Fiber Channel 1200-SM-LL-L XTS31U-10Lx 10 G Ethernet 10 km SFP+ Transceiver 10GBASE-LR/10GBASE-LW Features Compliant with IEEE Std 802.3-2005 10G Ethernet 10GBase-LR/LW
More informationPARAMETER SYMBOL MIN MAX UNITS NOTE
Features RoHS compliant Compatible with 155 Mbps ATM and SONET OC-3 SDH STM-1 Compliant with IEEE802.3ah 100Base-BX Compliant with ITU-T G.985 class S Industry standard 2 5 footprint SC Connector Single
More information10Gbps XFP Optical Transceiver RTXM
The is a hot pluggable 10Gbps small-form-factor transceiver module integrated with the high performance un-cooled 1310nm DFB laser and high sensitivity PIN receiver.it is compliant to INF-8077i XFP Multi-source
More information10Gbps XFP Optical Transceiver RTXM226-6XX
The RTXM226-6XX is a hot pluggable 10Gbps small-form-factor transceiver module integrated with the high performance cooled DWDM EML transmitter and high sensitivity APD receiver.it is compliant to INF-8077i
More informationSinglemode 155Mbps Optical Transceiver SFP with Digital Diagnostic
Features Compliant SFP MSA and SFF-8472(Rev 9.3) Compliant with GR-253-CORE SONET OC-3 and ITU-T G.957 SDH STM-1 specifications SFF-8472 Digital Diagnostic Monitoring Interface with real time monitors
More informationTRPUFEEEXx000E1G Fast Ethernet 100Base SFP Transceiver With Digital Diagnostics
Features Compliant with IEEE 802.3ah/D3.3 (100BASE-LX10) Compatible with SFP MSA RoHS6/6 Compliant Digital Diagnostics through Serial Interface Internal Calibration for Digital Diagnostics 1310nm Fabry
More information10Gb/s DWDM XFP Optical Transceiver AOX-DXX-R40
10Gb/s DWDM XFP Optical Transceiver Features Support 9.95Gb/s to 11.3Gb/s transmission Client side and Line side loopback functions Support 8.5G Fiber Channel Rate XFP MSA compliant form factor connector
More informationGb/s 1310 nm DML DFB Laser
1861 Gb/s 13 nm DML DFB Laser The 1861 directly-modulated laser (DML) is a cost-effective solution for Gb/s digital transmission of up to 60 km using traditional intra-city SMF-28 single-mode fiber links.
More informationXXDxxA-C0LY. 10Gbps DWDM XFP Optical Transceiver, 120km Reach. Features. Applications. Description. XXDxxA-C0LY 10Gbps DWDM XFP 120km Reach
XXDxxA-C0LY 10Gbps DWDM XFP 120km Reach XXDxxA-C0LY 10Gbps DWDM XFP Optical Transceiver, 120km Reach Features Wavelength selectable to C-band ITU-T grid wavelengths Suitable for use in 100GHz channel spacing
More informationArista QSFP-40G-PLR4. Part Number: QSFP-40G-PLR4 QSFP-40G-PLR4 OVERVIEW PRODUCT FEATURES APPLICATIONS FUNCTIONAL DIAGRAM.
Part Number: QSFP-40G-PLR4 QSFP-40G-PLR4 OVERVIEW The QSFP-40G-PLR4 is a parallel 40 Gbps Quad Small Form-factor Pluggable (QSFP+) optical module. It provides increased port density and total system cost
More informationProduct Specification OC-48 IR-1/STM S-16.1 Multirate 2x10 SFF Transceiver FTLF1421S1xCL
Product Specification OC-48 IR-1/STM S-16.1 Multirate 2x10 SFF Transceiver FTLF1421S1xCL PRODUCT FEATURES Up to 2.67Gb/s bi-directional data links Standard 2x10 pin SFF footprint (MSA compliant) Analog
More information10Gb/s XFP Tunable Optical Transceiver XFP-1080-DTZR. Preliminary Datasheet
10Gb/s XFP Tunable Optical Transceiver XFP-1080-DTZR Preliminary Datasheet Features Supports 9.95Gb/s to 11.3Gb/s transmission Client side and Line side loopback functions XFP MSA compliant form factor
More information10Gbps 1270/1330nm SFP+ BIDI TRx 40km
FEATURES Supports up to 10.3125Gb/s bit rates -40 to 85 C operating case temperature SFP+ package with single LC Receptacle connector 1270nm uncooled DFB laser transmitter and 1330nm PIN-TIA receiver Hot-pluggable
More informationProduct Specification. 10Gb/s 200km Telecom CML TM 13pin-GPO Butterfly Transmitter DM /1/2
Product Specification 10Gb/s 200km Telecom CML TM 13pin-GPO Butterfly Transmitter DM200-01-0/1/2 PRODUCT FEATURES High Performance CML TM Supports multi-bit-rate application, from 9.95Gb/s to 11.1Gb/s
More informationCWDM SFP 1.25G 40KM LC Duplex
CWDM SFP 1.25G 40KM LC Duplex SLSC-12XX-40-D Overview The SFP transceivers are high performance, cost effective modules supporting data-rate of 1.25Gbps and 40km transmission distance with SMF. The transceiver
More informationDWDM SFP Optical Transceiver
DWDM SFP Optical Transceiver Features Wavelength selectable to C-band and L-band ITU-T grid wavelengths Suitable for use in 100GHz channel spacing DWDM systems DWDM SFP MSA Compliant Up to 2. 667Gb/s data
More informationXENPAK-10GB-LRM XENPAK-10GBASE-LRM 1310nm, 220m Reach
Features XENPAK-10GB-LRM XENPAK-10GBASE-LRM 1310nm, 220m Reach Compatible with XENPAK MSA Rev.3.0 Support of IEEE802.3ae 10GBASE-LRM Transmission Distance up to 220m(MMF) Uncooled directly modulated 1310nm
More informationSFP 155Mb/s Transceiver 2km Hot Pluggable, Duplex LC, +3.3V, 1310nm FP-LD MM PSFP M-12F
DATASHEET DESCRIPTION: Transceiver is a high performance, cost effective module which have a Duplex LC optics interface. Standard AC coupled CML for high speed signal and LVTTL control and monitor signals.
More informationJGXD-XX192-08C J Great 80KM DWDM XFP Optical Transceiver
JGXD-XX192-08C J Great 80KM DWDM XFP Optical Transceiver Features Wavelength selectable to C-band ITU-T grid wavelengths Suitable for use in 100GHz channel spacing DWDM systems XFP MSA Compliant data rate
More informationTunable DWDM XFP, 80km
Tunable DWDM XFP, 80km Особенности: - 50GHz DWDM ITU Grid - Monolithic MZM Tunable TOSA + APD Receiver - 22dB бюджет - встроенная функция диагностики - двойной LC разъем - температурный диапазон от -5
More informationX2-10GB-LR-OC Transceiver, 1310nm, SC Connectors, 10km over Single-Mode Fiber.
X2-10GB-LR-OC Transceiver, 1310nm, SC Connectors, 10km over Single-Mode Fiber. Description These X2-10GB-LR-OC optical transceivers are designed for Storage, IP network and LAN. They are hot pluggable
More informationEPON OLT 1.25Gbps 1000Base-PX20 Tx1490/Rx1310nm DDMI SLEP-1143-P
EPON OLT 1.25Gbps 1000Base-PX20 Tx1490/Rx1310nm DDMI SLEP-1143-P Overview The SLEP-1143-P transceiver is the high performance module for single fiber by using 1490nm continuous-mode transmitter and 1310nm
More informationProduct Specification Sheet
Product Specification Sheet TISG4325S-CD20TC RoHS Compliant GPON SFP OLT C+ Optical Transceiver PRODUCT FEATURES Single Fiber Transceiver with single mode SC receptacle 1490nm continuous-mode transmitter
More informationPT (2)-1W. OC-3 SR/IR-1 / STM S-1.1 SFP Transceiver
www.neophotonics.com VER A/ 102307 PT7320-31(2)-1W 1 Features 1.1 Transceiver unit with independent 1310nm MQW FP Laser diode transmitter InGaAs PIN photodiode receiver 1.2 Compliant with SFP MSA and SFF-8472
More informationProduct Specification OC-48 SR-1/STM S-16 Multirate 2x10 SFF Transceiver FTLF1321S1xTL
Product Specification OC-48 SR-1/STM S-16 Multirate 2x10 SFF Transceiver FTLF1321S1xTL PRODUCT FEATURES Up to 2.67Gb/s bi-directional data links Standard 2x10 pin SFF footprint (MSA compliant) Analog diagnostics
More informationGNTP-4321S-C2CDA GPON SFP OLT Transceiver
Features GNTP-4321S-C2CDA GPON SFP OLT Transceiver Single Fiber Transceiver with single mode SC receptacle 1490nm continuous-mode transmitter with DFB laser 1310nm burst-mode receiver with APD-TIA Single
More informationDATASHEET 4.1. SFP+, 10GBase-ZR, Multirate Gbps, C Tunable, DWDM, C-Band, 50GHz, 22dB, 80km, ind. temp.
SO-SFP-10G-ZR-DWDM-I SFP+, 10GBase-ZR, Multirate 9.95-11.1 Gbps, C Tunable, DWDM, C-Band, 50GHz, 22dB, 80km, ind. temp. OVERVIEW The SO-SFP-10G-ZR-DWDM-I Tunable SFP+ Optical Transceiver is a full duplex,
More informationXFP-10G-Z-OC192-LR2-C
PROLABS XFP-10G-Z-OC192-LR2-C 10 Gigabit 1550nm Single Mode XFP Optical Transceiver XFP-10G-Z-OC192-LR2-C Overview PROLABS s XFP-10G-Z-OC192-LR2-C 10 GBd XFP optical transceivers are designed for 10GBASE-ZR,
More informationRoHS Compliant SFP Transceiver for SONET OC-48/SDH STM-16 with Digital Diagnostic Monitoring Function
RoHS Compliant SFP Transceiver for SONET OC-48/SDH STM-16 with Digital Diagnostic Monitoring Function FEATURES Compliant with SFP Transceiver SFF-8472 MSA specification with internal calibration LCP-2488B4JDR
More informationProduct Specification SFP WDM 100M 20km SC Transceiver
Product Specification 1. Product features Up to 155Mb/s data links 1310nm FP laser transmitter for XGSF-BS3503-20 1550nm DFB laser transmitter for XGSF-BS5303-20 Up to 20km on 9/125µm SMF Hot-pluggable
More informationV23870-A211x-xx00 (*) Bi-Directional Pigtail SFF Transceiver 155 Mb/s, 1310 nm Tx / 1310 nm Rx
Preliminary Data Sheet V23870-A211x-xx00 (*) Bi-Directional Pigtail SFF Transceiver 155 Mb/s, 1310 nm Tx / 1310 nm Rx FEATURES Integrated Beam Splitter Bi-Directional Transmission in a single optical window
More informationGPON SFP OLT Transceiver GNTP-4321S-B2CDA
Features GPON SFP OLT Transceiver GNTP-4321S-B2CDA Single Fiber Transceiver with single mode SC receptacle 1490nm continuous-mode transmitter with DFB laser 1310nm burst-mode receiver with APD-TIA Single
More informationProduct Specification. 10Gb/s DWDM 80km XFP Optical Transceiver FTRX xx
Product Specification 10Gb/s DWDM 80km XFP Optical Transceiver FTRX-3811-3xx PRODUCT FEATURES Supports 9.95Gb/s to 10.7Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 80km Temperature-stabilized
More informationHOLS-XPDxx4099-LD-xE
Honlus 40km DWDM XFP Optical Transceiver Features Wavelength selectable to C-band ITU-T grid wavelengths Suitable for use in 100GHz channel spacing DWDM systems XFP MSA Rev 4.5 Compliant Data rate from
More informationProduct Features. Applications. Descriptions. Ordering Information. LX432xCDR 10GEthernet 40km CWDM SFP+ Transceiver 10GBASE-LR / 10GBASE-LW
LX432xCDR Product Features Compliant with IEEE Std 802.3-2005 10G Ethernet 10GBase-LR/LW Electrical interface specifications per SFF-8431 Management interface specifications per SFF-8431 and SFF-8472 SFP+
More informationFeatures Gigabit Ethernet
Applicatios Gigabit Ethernet Ordering Information Features ü Up to 1.25Gb/s data links ü Single SC/LC connector ü Hot-pluggable SFP footprint ü 1550nm DFB laser transmitter ü RoHS compliant and Lead Free
More informationSFP BIDI 2.488Gbps 20KM 1550nm TX/1310nm RX
SFP BIDI 2.488Gbps 20KM 1550nm TX/1310nm RX XSFP-2553X-20X-X Overview The SFP-BIDI transceivers are high performance, cost effective modules supporting dual data-rate of 2.488Gbps/2.125Gbps and 20km transmission
More informationAA C 1000BASE-CWDM, Small Form-factor Pluggable (SFP), 1.25Gb/s data rate, 1590nm wavelength, 70Km reach
AA1419039-C 1000BASE-CWDM, Small Form-factor Pluggable (SFP), 1.25Gb/s data rate, 1590nm wavelength, 70Km reach FEATURES Up to 1.25Gb/s bi-directional data links Hot-pluggable SFP footprint 8 CWDM Wavelength
More informationPRODUCT FEATURES APPLICATIONS. Pin Assignment: 1 Gigabit Long-Wavelength SFP Transceiver SFP-SX-MM
1 Gigabit Long-Wavelength SFP Transceiver SFP-SX-MM PRODUCT FEATURES Up to 1.25Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions 850nm VCSEL laser transmitter
More informationXENPAK-10GB-SR XENPAK-10GBASE-SR 850nm, 300m Reach
Features XENPAK-10GB-SR XENPAK-10GBASE-SR 850nm, 300m Reach Compatible with XENPAK MSA Rev.3.0 Support of IEEE802.3ae up to 300m (OM3 MMF) Power Consumption 1.8W (typ.) Temperature Range 0 to 70 C Vertical
More informationFeatures: Compliance: Applications. Warranty: B21-GT Cisco 10Gb Ethernet Base CX4 X2 Module HP Compatible
The GigaTech Products is programmed to be fully compatible and functional with all intended HP switching devices. This X2 optical transceiver is designed for IEEE 802.3ae 10GBASE-LR interconnects and is
More informationProduct Specification. 10Gb/s 80km Multi-Rate XFP Optical Transceiver FTLX1812M3BCL
Product Specification 10Gb/s 80km Multi-Rate XFP Optical Transceiver FTLX1812M3BCL PRODUCT FEATURES Supports 9.95Gb/s to 11.35Gb/s bit rates Hot-pluggable XFP footprint Maximum link length of 80km RoHS-6
More informationF i n i s a r. Product Specification. Long-Reach DWDM SFP Transceiver FWLF1631Rxx PRODUCT FEATURES
Product Specification Long-Reach DWDM SFP Transceiver FWLF1631Rxx PRODUCT FEATURES Up to 2.7 Gb/s bi-directional data links High launch power (+3dBm MIN) Hot-pluggable SFP footprint Temperature-stabilized
More informationGigabit Ethernet LC Bi-directional SFP Transceiver (80km) RBT12SZX
RoHS Compliant Gigabit Ethernet LC Bi-directional SFP Transceiver (80km) RBT12SZX Applications Gigabit Ethernet 1X Fiber Channel Features Description RoHS compliant Bi-directional GbE single / multi-rate
More information10Gb/s CWDM SFP+ 80km Transceiver
PRODUCT FEATURES 10Gb/s CWDM SFP+ 80km Transceiver Up to 11.1Gbps Data Links Up to 80km transmission on SMF Power dissipation < 1.5W CWDM EML Laser and APD receiver Metal enclosure, for lower EMI 2-wire
More informationLinkPower LPS SM BIDI 2612TC/2612TI & 2613RC/2613RI SC. RoHS Compliant 1.25G 1310/1550nm & 1550/1310nm 20km Transceivers
LinkPower LPS SM BIDI 2612TC/2612TI & 2613RC/2613RI SC RoHS Compliant 1.25G 1310/1550nm & 1550/1310nm 20km Transceivers Product Features 1. Supports 1.25Gbps/1.0625Gbps bit rates 2. Bi-Directional, BIDI,
More information3.3V / 1550 nm / 622 Mbps Digital Diagnostic LC SFP SINGLE-MODE TRANSCEIVER
/ SPS-00BWG / SPS-00AWG (RoHS Compliant).V / 10 nm / 6 Mbps Digital Diagnostic LC SFP SINGLE-MODE TRANSCEIVER FEATURES Hot-Pluggable SFP Footprint LC Optical Transceiver Small Form-Factor Pluggable (SFP)
More informationTRS-3050G / TRS-3050TG / TRS-3050FG / TRS-3050AG / TRS-3050ATG / TRS-3050AFG. 3.3V / 1310 nm / 155 Mbps RoHS Compliant Optical Single-Mode Transceiver
* / TRS-3050TG / TRS-3050FG / TRS-3050AG / TRS-3050ATG / TRS-3050AFG 3.3V / 1310 nm / 155 Mbps RoHS Compliant Optical Single-Mode Transceiver FEATURES Duplex SC Single Mode Transceiver: Duplex ST Single
More information10Gb/s 80km DWDM XFP Optical Transceiver
10Gb/s 80km DWDM XFP Optical Transceiver PRODUCT FEATURES Hot-pluggable XFP footprint Supports 9.95Gb/s to 11.3Gb/s bit rates Supports Lineside and XFI loopback RoHS-6 Compliant (lead-free) Power dissipation
More informationPart Number Transmitter Output Power Receiver Sensitivity Reach Temp DDM RoHS
Product Features Compliant with IEEE Std 802.3-2005 10Gb Ethernet 10GBase-BX XFP MSA Rev. 4.5 compliant Full digital diagnostic management interface XFP MSA package with Single LC receptacle optical Uncooled
More informationProduct Specification OC-12 SR-1/STM I-4 or OC-12 IR-1/STM S-4.1 2x5 SFF Transceiver FTLF1322F2xTR
Product Specification OC-12 SR-1/STM I-4 or OC-12 IR-1/STM S-4.1 2x5 SFF Transceiver FTLF1322F2xTR PRODUCT FEATURES Up to OC-12/STM-4 bi-directional data links Standard 2x5 pin SFF footprint (MSA compliant)
More information10Gb/s CWDM Electro-absorption Modulated Lasers (EML) TOSA
10Gb/s CWDM Electro-absorption Modulated Lasers (EML) TOSA FGT9xx-Txxx-00 Description: The Fiber-Grid FGT9xx series EML TOSA modules consists of a multi-quantum-well laser and a monolithically integrated
More informationXFP Series JD1310-XFP-LC.S10. Features. Applications. Ordering information
JD1310-XFP-LC.S10 1310nm XFP single-mode for 10GbE/10GFC/SDH/SONET Duplex XFP Transceiver RoHS6 Compliant XFP Series Features Supports 9.95Gb/s to 11.3Gb/s bit rates Hot-pluggable XFP footprint Link length
More information