Transcription

1

2 DIN Rail Power Supplies Since 1984, Altech Corporation has grown to become a leading supplier of automation and industrial control components. Headquartered in Flemington, NJ, Altech has an experienced staff of engineering, manufacturing and sales personnel to provide the highest quality products with superior service. This is the Altech Commitment! In response to a growing market for high power regulated Power Supplies, Altech introduced the new Din Rail mountable power supply line. They are reliable, cost effective, space economical and easy to install and maintain. They are able to handle any industrial process requirement. In addition, you do not need to oversize them; they are designed to work on % load capacity. The universal input, power factor correction and many approvals proves that Altech Power Supplies will function worldwide on a wide variety of applications. Wide operation temperature range, high efficiency and many protections make Altech Power supplies your best choice. Our well trained technical experts welcome the opportunity to answer your technical questions and provide solutions to your automation and control needs. Give us a call or visit Quality Commitment

3 DIN Rail Power Supplies Selection Guide 4-5 PSC Compact Class Series Compact Design and Lightweight Class, UL 1310 Recognized Brown-out protection 10W to 480W rated power Universal single phase input 6-35 PSA Flex Series (1 Phase) Flex power, solid metal housing UL 508 listed 10W to 600W rated power High efficiency with Boost Power Single phase input PSB Flex Series ( & 3 Phase) Flex power, solid metal housing UL 508 listed 10W to 600W rated power High efficiency with Boost Power Two and Three phase input PS-S Slim line Series Slim Line Design, plastic housing UL 508 listed contact 10W to W rated power Universal single phase input PS Low Profile Series Low profile Design, plastic housing UL Recognized Isolation Class II 10W to W rated power Universal single phase input 7-85 PS Industrial Series Robust Metal housing UL 508 listed Built in active PFC function 75W to 960W rated power Single and three phase universal input PS-C and W Series Narrow design, small metal housing UL 508 listed 150% pick load capacity 10W to 480W rated power Single and two phase wide input CBI DC UPS System Fully automated battery care module Three charging modes 1, 4, 36 and 48V DC single outputs / VAC input System start from battery function CB Battery Chargers Intelligent battery chargers Suitable for most common battery types Adjustable charging current VDC and 4VDC single output VAC input Accessories Redundancy diode module UPS controller module Battery holders and enclosures Ultra capacitor modules FAQ Index Terms & Conditions 3

4 PS Low Profile PS-S Slimine PSA & PSB Flex PSC Class Compact SINGLE PHASE SINGLE PHASE TWO (THREE) PHASE SINGLE PHASE Cat. No. PSC-10xx PSC-0xx PSC-xx PSC-60xx PSC-96xx PSC-151xx PSC-41xx PSC-481xx PSC-RM0 PSA-10xx PSA-180xx PSA-360xx PSA-600xx PSB-10xx PSB-180xx PSB-360xx PSB-600xx PS-S10xx PS-S0xx PS-Sxx PS-S60xx PS-Sxx PS-15xx PS-30xx PS-45xx PS-60xx PS-xx Selection Guide Choose your product from a wide range of features and options, suitable for almost all applications. Rated Current VDC A 0.67A 0.4A 1.7A 1.4A 1A 3.4A.7A 1.7A 0.85A 4A 5A.5A 1.5A 7.5A 6.4A 4A A 6.3A 3.A 10A 5A 0A 10A 0A 5A 7.5A 14A 5A 5A 7.5A 14A 5A A 0.84A 0.67A 0.4A 3A 1.67A 1.34A 1 6A 3.33A 1.7A 0.83A 10A 5A.5A 1.5A 7.5A 4A A.4A 1.5A 1A 0.63A 3A A A 1.5A 5A 3.5A.8A A 6.5A 4.5A 4A.5A 7.5A 6.5A 4.A Universal Input Switch Select Input Parallel Option UL 508 Listed UL Rec. UL 1310 Rec. EN NEC Class Compliant Short Circuit Overload Over Voltage Over Temperature CB 4

5 Selection Guide Choose your product from a wide range of features and options, suitable for almost all applications. PS Industrial SINGLE PHASE THREE PHASE Cat. No. PS-75xx PS-10xx PSH-10xx PSP-xx PSP-480xx PSP-480Sxx PST-xx PST-480xx PST-960xx VDC PST-960Pxx Output Voltage A 3.A 1.6A 10A 5A.5A 5A.5A 10A 5A 0A 10A 0A 10A 10A 5A 0A 10A A 0A A 0A Universal Input Switch Select Input Parallel Option UL 508 Listed UL Rec. UL 1310 Rec. EN NEC Class Compliant Short Circuit Overload Over Voltage Over Temperature CB Compact Housing SINGLE PHASE WIDE VOLTAGE PS-C10xx PS-Cxx PSH-C480xx PSP-C480Pxx PSW-10xx PSW-xx PSW-480Pxx 10A 5A.5A 10A 5A 0A 10A 0A 10A 10A 5A.5A 10A 5A 0 10 CBI1xx 3-5A DC-UPS CBI4xx CBI48xx CBI80 xx 3-0A 5-10A 1V/15A 4V/10A 36V/7A 48V/5A MULTI-VOLTAGE MULTI-VOLTAGE Battery Charger CB1xx 3-35A CB4xx 3-0A CB145A 6 A 5 A Acces. PS-RDN 1-8V PS-UPS 1-8V Three Phase Input Selected items, see data sheet 0V INPUT ONLY Special order item / not UL approved. Wide Range Input signal 5

6 Compact Single Phase Power Supply (PSC) ALTECH s Compact DIN rail switching power supply, PSC Series designed for the fast growing demand of DIN rail applications. These 10W to 480W models are enclosed with fully isolated plastic or metal case to prevent users from hazardous shock. The design complies with the compact requirements that the precious space on the industrial rail can be preserved effectively. Featuring up to 94% of efficiency, this series is cooled only by free air convection up to 70 C that significantly increase the reliability and lifetime of the power supply. Another important feature of PSC Series is its low power consumption (<0.75W) This unique characteristic can significantly expand the application of PSC series beyond just heavy industrial field, but can also be implied to dotcom or IT applications that require green power to save the energy and to obey the anticipated government laws in the near future! Short circuit protection, overload protection, over voltage protection, and the signal for monitoring the status of power supply are standard functions for the PSC Series. Typical applications include factory automation, process control, electro-mechanical industry, dotcom and IT. Input voltage range: AC inrush current (max): Cold start: DC adjustment range: Overload protection: Over-voltage protection: Other protection: Setup, rise, time (max): Withstand voltage: Working temperature: Safety standards: EMC standards: Military Standard Vibration On/Off 85-64V AC; V DC 0A at 115V AC; A at 30V AC ±10% rated output voltage 105% rated output power 115%-150% rated output voltage Brown out protection 500ms, 30ms/30V AC 0ms, 30ms/115V AC, at full load I/P-O/P: 3KV AC, I/P-FG:1.5KV AC, O/P-FG:0.5KV AC -0 to +70 C (-4 to +158 F), refer to output de-rating curve UL508 listed, UL1310 recognized, TUV approved EN compliant EN550 class B EN60-4-,3,4,5,6,8,11 ENV5004; EN5504; EN60-6-1; EN6104-3; Light Industry Level criteria A MIL-HDBK-17F withstands G test Built in remote ON/OFF function (metal case only) 6

7 Compact Single Phase Power Supply (PSC) Features: Universal AC input/full range Protections: Short circuit / Overload / Overvoltage Cooling by free air convection DIN rail mountable UL1310 NEC class / LPS compliant (1V,4V,48V only) No load power consumption <0.75W LED indicator for power on % full load burn-in test relay contact 3 year warranty Multiple output connector for easy wiring on PS-S, PS-S60 and PS-S models 35mm DIN Rail Mounting Robust plastic housing DC on LED signal Adjustable DC output voltage Easy to understand layout panel CE Compliance UL508 Listed UL1310 Recognized Universal Input Compact for maximized panel space Multiple output connector for easy wiring 35mm DIN Rail Mounting Adjustable DC output voltage DC on LED signal Easy to understand layout panel CE Compliance Metal housing Universal Input Compact for maximized panel space 7

8 Compact Single Phase Power Supply (PSC) E E W Single Output Industrial DIN Rail Power Supply Cat. No. Output Tol. Ripple & Efficiency NOTES V DC A % Noise PSC-101 1V DC 0.84A ±1% mvp-p 81% PSC V DC 0.67A ±1% mvp-p 81% PSC-104 4V DC 0.4A ±1% 10 mvp-p 81% 0W Single Output Industrial DIN Rail Power Supply Cat. No. Output Tol. Ripple & Efficiency NOTES V DC A % Noise PSC-01 1V DC 1.7A ±1% mvp-p 83% PSC V DC 1.4A ±1% mvp-p 85% PSC-04 4V DC 1A ±1% 10 mvp-p 86% W Single Output Industrial DIN Rail Power Supply Cat. No. Output Tol. Ripple & Efficiency NOTES V DC A % Noise PSC-1 1V DC 3.4A ±1% mvp-p 84% PSC-15 15V DC.7A ±1% mvp-p 84% PSC-4 4V DC 1.7A ±1% 10 mvp-p 84% PSC-48 48V DC 0.85A ±1% 180 mvp-p 85% 60W Single Output Industrial DIN Rail Power Supply Cat. No. Output Tol. Ripple & Efficiency NOTES V DC A % Noise PSC-601 1V DC 5A ±1% mvp-p 86% PSC V DC 4A ±1% mvp-p 87% PSC-604 4V DC.5A ±1% 10 mvp-p 87% PSC V DC 1.5A ±1% 180 mvp-p 88% 96W Single Output Industrial DIN Rail Power Supply Cat. No. Output Tol. Ripple & Efficiency NOTES V DC A % Noise PSC-961* 1V DC 7.5A ±1% 180 mvp-p 87% PSC-9615* 15V DC 6.4A ±1% 180 mvp-p 87% PSC-964 4V DC 4A ±1% 180 mvp-p 88% PSC V DC A ±1% 50 mvp-p 87% *Not included in UL file E

9 SPECIFICATIONS PSC-10 Terminal Pin. No Assign. (TB1) Terminal Pin. No Assign. (TB) Series 1 FG 4 DC +V AC/N 5 DC -V 3 AC/L 6 SIGNAL 99 3 PSC-0 Series Terminal Pin. No Assign. (TB1) Terminal Pin. No Assign. (TB) 1 FG 4 DC +V AC/N 5 DC -V 3 AC/L 6 SIGNAL 99 3 PSC- Series Terminal Pin. No Assign. (TB1) Terminal Pin. No Assign. (TB) 1 FG 1/ DC +V AC/N 3/4 DC -V 3 AC/L 5/6 Relay Contact 99 PSC-60 Series Terminal Pin. No Assign. (TB1) Terminal Pin. No Assign. (TB) 1 FG 1/ DC +V AC/N 3/4 DC -V 3 AC/L 5/6 Relay Contact 99 PSC-96 Series Terminal Pin. No Assign. (TB1) Terminal Pin. No Assign. (TB) 1 FG 1/ DC +V AC/N 3/4 DC -V 3 AC/L 5/6 Relay Contact 9

10 PSC-10 Series E E0541 Features: Universal AC input (88-64V AC) Protections: Short Circuit / Overload / Overvoltage Brown-out protection Installed on DIN rail TS35 / 7.5 or 15 True signal output All wiring 105 C long life electrolytic capacitors High operation temperature up to 70 C Withstands G vibration test High efficiency, long life and high reliability 3 year warranty UL1310 Class Power unit / LPS pass UL508 (Industrial control equipment) listed INPUT PROTECTION ENVIRONMENT SAFETY & EMC Cat. No. PSC-101 PSC-1015 PSC-104 DC VOLTAGE 1V 15V 4V RATED CURRENT 0.84A 0.67A 0.4A CURRENT RANGE 0~0.84A 0~0.67A 0~0.4A RATED POWER 10.08W 10.05W 10.08W RIPPLE & NOISE (max) mvp-p mvp-p 10mVp-p Ripple & noise are measured at 0MHz of bandwidth by using a 1 twisted pair-wire terminated with a 0.1µF & 47µF parallel capacitor VOLTAGE ADJ. RANGE 10.8~13.V 13.5~16.5V 1.6~6.4V VOLTAGE TOLERANCE ±1.0% ±1.0% ±1.0% Tolerance: includes set up tolerance, line regulation and load regulation. LINE REGULATION ±1.0% ±1.0% ±1.0% LOAD REGULATION ±1.0% ±1.0% ±1.0% SETUP, RISE TIME < 800ms, < ms/30v AC at full load HOLD UP TIME (Typ.) > 3ms / 30V AC; > 16ms / 115V AC at full load VOLTAGE RANGE 88V~64VAC; 14V~370VDC Derating may be needed under low input voltages. Please check the derating curve for more details. FREQUENCY RANGE 47~63Hz EFFICIENCY (Typ.) 81% 81% 81% AC CURRENT (Typ.) 0.3A/115VAC; 0.17A/30VAC INRUSH CURRENT (Typ.) 15A / 115V AC; 30A / 30V AC LEAKAGE CURRENT < 1mA/ 30VAC OVERLOAD PROTECTION OVERVOLTAGE PROTECTION > 10% rated output power Protection type: Constant current limiting, recovers automatically after fault condition is removed. 115%~150% rated output voltage Protection type: Latch-off mode. OVER TEMPERATURE PROTECTION Power supply shut down at 70 C constant current limiting / output voltage goes to 0; re-power on to recover WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. / HUMIDITY TEMP. COEFFICIENT VIBRATION -0 ~ +70 C (Refer to output load derating curve) 0 ~ % RH non-condensing - ~ +85 C; 10 ~ 95% RH ±0.03% / C (0 ~ 50 C) 10 ~ 500Hz, G 10min. / 1cycle, 60 min. each long X,Y, Z axes SAFETY STANDARDS UL508, TUV EN :006+A11, UL1310 NEC class compliant WITHSTAND VOLTAGE I/P-O/P: 3KVAC (44DC) I/P-FG: 1.5KVAC (11DC) 1 minute ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG: M Ohms/500VDC EMI CONDUCTION & RADIATION EN550:006+A1:007 Class B HARMONIC CURRENT EN60-3-:006 Class A, EN60-3-3:008 EMS IMMUNITY EN6104-3:000, EN5504:1998+A1:001+A:003 light industry level, criteria A The power supply is considered a component which will installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. Signal Open collector. Max: ma MTBF 56.7K hrs MIL-HDBK-17K DIMENSION 3xx99 mm (WxHxD) PACKING 0.13Kg/48 pcs. / 7.44Kg CONNECTION I/P 3 poles, O/P: 3 poles screw DIN terminal COOLING Free air convection All parameters NOT specially mentioned are measured at 30V AC input, rated load and 5 C of ambient temperature. 10

11 PSC-10 Series Mechanical Specification Unit : mm / inch 3 99 Terminal Pin. No Assign. (TB1) 1 FG AC/N 3 AC/L Terminal Pin. No Assign. (TB) 4 DC +V 5 DC -V 6 SIGNAL 5 5 Application of Active Signal (a)5v signal (b)led (c)relay R 5.1V Model 1V 15V R R Model 1V 15V R Relay RL Model 1V 15V R V- 4V V- 4V V- 4V Block Diagram I/P EMI FILTER RECTIFIERS & FILTER POWER SWITCHING RECTIFIERS & FILTER +V -V O.C.P DETECTION O.L.P. CONTROL O.V.P. Derating Curve Load V.S Temp. Load V.S I/P Voltage Ta=5 C VAC Ambient Temperature ( C) Input Voltage(VAC) 60Hz Note: All dimensions are in millimeters, to convert to inches multiply by

12 PSC-0 Series E E0541 Features: Universal AC input (88-64V AC) Protections: Short Circuit / Overload / Overvoltage Brown-out protection Installed on DIN rail TS35 / 7.5 or 15 True signal output All wiring 105 C long life electrolytic capacitors High operation temperature up to 70 C Withstands G vibration test High efficiency, long life and high reliability 3 year warranty UL1310 Class Power unit / LPS pass UL508 (Industrial control equipment) listed INPUT PROTECTION ENVIRONMENT SAFETY & EMC Cat. No. PSC-01 PSC-015 PSC-04 DC VOLTAGE 1V 15V 4V RATED CURRENT 1.7A 1.4A 1A CURRENT RANGE 0~1.7A 0~1.4A 0~1A RATED POWER 0.4W 1W 4W RIPPLE & NOISE (max) mvp-p mvp-p 10mVp-p Ripple & noise are measured at 0MHz of bandwidth by using a 1 twisted pair-wire terminated with a 0.1µF & 47µF parallel capacitor VOLTAGE ADJ. RANGE 10.8~13.V 13.5~16.5V 1.6~6.4V VOLTAGE TOLERANCE ±1.0% ±1.0% ±1.0% Tolerance: includes set up tolerance, line regulation and load regulation. LINE REGULATION ±1.0% ±1.0% ±1.0% LOAD REGULATION ±1.0% ±1.0% ±1.0% SETUP, RISE TIME < 800ms, < ms/30v AC at full load HOLD UP TIME (Typ.) > 3ms / 30V AC; > 16ms / 115V AC at full load VOLTAGE RANGE 88V~64VAC; 14V~370VDC Derating may be needed under low input voltages. Please check the derating curve for more details. FREQUENCY RANGE 47~63Hz EFFICIENCY (Typ.) 83% 85% 86% AC CURRENT (Typ.) 0.45A/115VAC; 0.3A/30VAC INRUSH CURRENT (Typ.) 0A / 115V AC; A / 30V AC LEAKAGE CURRENT < 1mA/ 30VAC OVERLOAD PROTECTION OVERVOLTAGE PROTECTION > 105% rated output power Protection type: Constant current limiting, recovers automatically after fault condition is removed. 115%~150% rated output voltage Protection type: Latch-off mode. OVER TEMPERATURE PROTECTION Power supply shut down at 70 C constant current limiting / output voltage goes to 0; re-power on to recover WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. / HUMIDITY TEMP. COEFFICIENT VIBRATION -0 ~ +70 C (Refer to output load derating curve) 0 ~ % RH non-condensing - ~ +85 C; 10 ~ 95% RH ±0.03% / C (0 ~ 50 C) 10 ~ 500Hz, G 10min. / 1cycle, 60 min. each long X,Y, Z axes SAFETY STANDARDS UL508, TUV EN :006+A11, UL1310 NEC class compliant WITHSTAND VOLTAGE I/P-O/P: 44DC I/P-FG: 11DC 1 minute ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG: M Ohms/500VDC EMI CONDUCTION & RADIATION EN550:006+A1:007 Class B HARMONIC CURRENT EN60-3-:006 Class A, EN60-3-3:008 EMS IMMUNITY EN6104-3:000, EN5504:1998+A1:001+A:003 light industry level, criteria A The power supply is considered a component which will installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. Signal Open collector. Max: ma MTBF 10.4K HRS MIL-HDBK-17 (5 C) 131.3K HRS MIL-HDBK-17 (5 C) 15.9K HRS MIL-HDBK-17 (5 C) DIMENSION 3xx99 mm (WxHxD) PACKING 0.14Kg/48 pcs./7.9kg CONNECTION I/P 3 poles, O/P: 3 poles screw DIN terminal COOLING Free air convection All parameters NOT specially mentioned are measured at 30V AC input, rated load and 5 C of ambient temperature. 1

13 PSC-0 Series Mechanical Specification Unit : mm / inch 3 99 Terminal Pin. No Assign. (TB1) 1 FG AC/N 3 AC/L Terminal Pin. No Assign. (TB) 4 DC +V 5 DC -V 6 SIGNAL 5 5 Application of Active Signal (a)5v signal (b)led (c)relay R 5.1V Model R 1V 1.5K 15V K R Model R 1V.4K 15V 3K Relay RL Model R 1V V 700 V- 4V 3.9K V- 4V 4.7K V- 4V 1.K Block Diagram I/P EMI FILTER RECTIFIERS & FILTER POWER SWITCHING RECTIFIERS & FILTER +V -V O.C.P DETECTION O.L.P. CONTROL O.V.P. Derating Curve Load V.S Temp. Load V.S I/P Voltage Ta=5 C VAC Ambient Temperature ( C) Input Voltage(VAC)60Hz Note: All dimensions are in millimeters, to convert to inches multiply by

14 PSC- Series E E0541 Features: Universal AC input (88-64V AC) Protections: Short Circuit / Overload / Overvoltage Brown-out protection Installed on DIN rail TS35 / 7.5 or 15 True signal output All wiring 105 C long life electrolytic capacitors High operation temperature up to 70 C Withstands G vibration test High efficiency, long life and high reliability 3 year warranty UL1310 Class Power unit / LPS pass UL508 (Industrial control equipment) listed INPUT PROTECTION ENVIRONMENT SAFETY & EMC Cat. No. PSC-1 PSC-15 PSC-4 PSC-48 DC VOLTAGE 1V 15V 4V 48V RATED CURRENT 3.4A.7A 1.7A 0.85A CURRENT RANGE 0 ~ 3.4A 0 ~.7A 0 ~ 1.7A 0 ~ 0.85A RATED POWER.8W.5W.8W.8W RIPPLE & NOISE (max) mvp-p mvp-p 10mVp-p 180mVp-p Ripple & noise are measured at 0MHz of bandwidth by using a 1 twisted pair-wire terminated with a 0.1µF & 47µF parallel capacitor VOLTAGE ADJ. RANGE 10.8 ~ 13.V 13.5 ~ 16.5V 1.6 ~ 6.4V 43. ~ 5.8V VOLTAGE TOLERANCE ±1.0% ±1.0% ±1.0% ±1.0% Tolerance: includes set up tolerance, line regulation and load regulation. LINE REGULATION ±1.0% ±1.0% ±1.0% ±1.0% LOAD REGULATION ±1.0% ±1.0% ±1.0% ±1.0% SETUP, RISE TIME < 800ms, < 50ms / 30VAC at full load HOLD UP TIME (Typ.) > 3ms / 30VAC; >16ms / 115VAC at full load VOLTAGE RANGE 88 ~ 64VAC; 14 ~ 370VDC Derating may be needed under low input voltages. Please check the derating curve for more details. FREQUENCY RANGE EFFICIENCY (Typ.) 47~63Hz 84% 84% 84% 85% AC CURRENT (Typ.) 0.8 A / 115VAC; 0.4A / 30VAC INRUSH CURRENT (Typ.) COLD START 30A / 115VAC; 60A / 30VAC LEAKAGE CURRENT < 1mA/ 30VAC OVERLOAD PROTECTION OVERVOLTAGE PROTECTION > 105% rated output power Protection type: Constant current limiting, recovers automatically after fault condition is removed. 115% ~ 150% rated output voltage Protection type: latch-off mode OVER TEMPERATURE PROTECTION Power supply shut down at 70 C constant current limiting / output voltage goes to 0; re-power on to recover WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. / HUMIDITY TEMP. COEFFICIENT VIBRATION -0 ~ +70 C (Refer to output load derating curve) 0 ~ % RH non-condensing - ~ +85 C; 10 ~ 95% RH ±0.03% / C (0 ~ 50 C) 10 ~ 500Hz, G 10min. / 1cycle, 60 min. each long X,Y, Z axes SAFETY STANDARDS UL508, TUV EN :006+A11, UL1310 NEC class compliant WITHSTAND VOLTAGE I/P-O/P: 44DC I/P-FG: 11DC 1 minute ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG: M Ohms/500VDC EMI CONDUCTION & RADIATION EN550: 006 Class B HARMONIC CURRENT EN60-3-: 006 Class A, EN60-3-3: 1995+A1: 001+A: 005 EMS IMMUNITY EN6104-3:000, EN5504:1998+A1:001+A:003 light industry level, criteria A The power supply is considered a component which will installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. Signal Relay contact (30VDC / 1A, 10VAC / 1A) MTBF 947.K hrs MIL-HDBK-17K DIMENSION xx99 mm (WxHxD) PACKING 0.8Kg/7 pcs./8.76kg CONNECTION I/P 3 poles, O/P: 6 poles screw DIN terminal COOLING Free air convection All parameters NOT specially mentioned are measured at 30V AC input, rated load and 5 C of ambient temperature. 14

15 PSC- Series Mechanical Specification Unit : mm / inch 99 Terminal Pin. No Assign. (TB1) Pin No. Assignment 1 FG 3 AC/N AC/L Terminal Pin. No Assign. (TB) 1, DC +V 3,4 DC -V 5,6 RELAY CONTACT N L Block Diagram I/P EMI FILTER RECTIFIERS & FILTER POWER SWITCHING RECTIFIERS & FILTER +V -V O.C.P. DETECTION O.L.P. CONTROL O.V.P. Relay Contact Contact Close Contact Open Contact Ratings (max.) When the output voltage reaches the adjusted output voltage When the output voltage drop below % rated output voltage 30V / 1A resistive load Derating Curve Load V.S Temp. Load V.S I/P Voltage Ta=5 C VAC Ambient Temperature ( C) Input Voltage(VAC)60Hz Note: All dimensions are in millimeters, to convert to inches multiply by

16 PSC-60 Series E E0541 Features: Universal AC input (88-64V AC) Protections: Short Circuit / Overload / Overvoltage Brown-out protection Installed on DIN rail TS35 / 7.5 or 15 True signal output All wiring 105 C long life electrolytic capacitors High operation temperature up to 70 C Withstands G vibration test High efficiency, long life and high reliability 3 year warranty UL1310 Class Power unit / LPS pass UL508 (Industrial control equipment) listed INPUT PROTECTION ENVIRONMENT SAFETY & EMC Cat. No. PSC-601 PSC-6015 PSC-604 PSC-6048 DC VOLTAGE 1V 15V 4V 48V RATED CURRENT 5A 4A.5A 1.5A CURRENT RANGE 0 ~ 5A 0 ~ 4A 0 ~.5A 0 ~ 1.5A RATED POWER 60W 60W 60W 60W RIPPLE & NOISE (max) mvp-p mvp-p 10mVp-p 180mVp-p Ripple & noise are measured at 0MHz of bandwidth by using a 1 twisted pair-wire terminated with a 0.1µF & 47µF parallel capacitor VOLTAGE ADJ. RANGE 10.8 ~ 13.V 13.5 ~ 16.5V 1.6 ~ 6.4V 43. ~ 5.8V VOLTAGE TOLERANCE ±1.0% ±1.0% ±1.0% ±1.0% Tolerance: includes set up tolerance, line regulation and load regulation. LINE REGULATION ±1.0% ±1.0% ±1.0% ±1.0% LOAD REGULATION ±1.0% ±1.0% ±1.0% ±1.0% SETUP, RISE TIME < 800ms, < 50ms / 30VAC at full load Length of set up time is measured at sold first start. Turning ON/OFF the power supply may lead to increase of the set up time. HOLD UP TIME (Typ.) > 3ms / 30VAC; >16ms / 115VAC at full load VOLTAGE RANGE 88 ~ 64VAC; 14 ~ 370VDC Derating may apply in low input voltage. Please check the derating curve for more details. FREQUENCY RANGE 47~63Hz EFFICIENCY (Typ.) 86% 87% 87% 88% AC CURRENT (Typ.) 1.3 A / 115VAC; 0.6A / 30VAC INRUSH CURRENT (Typ.) COLD START 30A / 115VAC; 60A / 30VAC LEAKAGE CURRENT <1mA / 30VAC OVER LOAD PROTECTION > 10% rated output power Protection type: Constant current limiting, recovers automatically after fault condition is removed OVER VOLTAGE PROTECTION 115% ~ 150% rated output voltage Protection type: latch-off mode OVER TEMPERATURE PROTECTION Power supply shut down at 70 C constant current limiting / output voltage goes to 0; re-power on to recover WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. / HUMIDITY TEMP. COEFFICIENT VIBRATION -0 ~ +70 C (Refer to output load derating curve) 0 ~ % RH non-condensing - ~ +85 C; 10 ~ 95% RH ±0.03% / C (0 ~ 50 C) 10 ~ 500Hz, G 10min. / 1cycle, 60 min. each long X,Y, Z axes SAFETY STANDARDS UL508, TUV EN :006+A11, UL1310 NEC class compliant WITHSTAND VOLTAGE I/P-O/P: 44DC, I/P-FG: 11DC 1 minute ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG: M Ohms/500VDC EMI CONDUCTION & RADIATION EN550: 006 Class B HARMONIC CURRENT EN60-3-: 006 Class A, EN60-3-3: 1995+A1: 001+A: 005 EMS IMMUNITY EN6104-3: 000, EN5504: 1998+A1:001+A: 003 light industry level, criteria A The power supply is considered a component which will installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. Signal Relay contact (4VDC / 1A, 10VAC / 1A) MTBF 944.6K HRS MIL-HDBK-17F DIMENSION xx99 mm (WxHxD) PACKING 0.3kg; 7pcs / 9.3kg CONNECTION I/P: 3 poles, O/P: 6 poles screw DIN terminal COOLING Free air convection All parameters NOT specially mentioned are measured at 30V AC input, rated load and 5 C of ambient temperature. 16

17 PSC-60 Series Mechanical Specification Unit : mm / inch 99 Terminal Pin. No Assign. (TB1) Pin No. Assignment 1 FG 3 AC/N AC/L Terminal Pin. No Assign. (TB) 1, DC +V 3,4 DC -V 5,6 RELAY CONTACT N L Block Diagram I/P EMI FILTER RECTIFIERS & FILTER POWER SWITCHING RECTIFIERS & FILTER +V -V O.C.P. DETECTION O.L.P. CONTROL O.V.P. Relay Contact Contact Close Contact Open Contact Ratings (max.) When the output voltage reaches the adjusted output voltage When the output voltage drop below % rated output voltage 30V / 1A resistive load Derating Curve Load V.S Temp. Load V.S I/P Voltage Ta=5 C VAC Ambient Temperature ( C) Input Voltage(VAC)60Hz Note: All dimensions are in millimeters, to convert to inches multiply by

18 PSC-96 Series E E0541 Features: Universal AC input (88-64V AC) Protections: Short Circuit / Overload / Overvoltage Brown-out protection Installed on DIN rail TS35 / 7.5 or 15 True signal output All wiring 105 C long life electrolytic capacitors High operation temperature up to 70 C Withstands G vibration test High efficiency, long life and high reliability 3 year warranty UL1310 Class Power unit / LPS pass UL508 (Industrial control equipment) listed INPUT PROTECTION ENVIRONMENT SAFETY & EMC Cat. No. PSC-961* PSC-9615* PSC-964 PSC-9648 DC VOLTAGE 1V 15V 4V 48V RATED CURRENT 7.5A 6.4A 4A A CURRENT RANGE 0 ~ 7.5A 0 ~ 6.4A 0 ~ 4A 0 ~ A RATED POWER W 96W 96W 96W RIPPLE & NOISE (max) 180mVp-p 180mVp-p 180mVp-p 50mVp-p Ripple & noise are measured at 0MHz of bandwidth by using a 1 twisted pair-wire terminated with a 0.1µF & 47µF parallel capacitor VOLTAGE ADJ. RANGE 10.8 ~ 13.V 13.5 ~ 16.5V 1.6 ~ 6.4V 43. ~ 5.8V VOLTAGE TOLERANCE ±1.0% ±1.0% ±1.0% ±1.0% Tolerance: includes set up tolerance, line regulation and load regulation. LINE REGULATION ±1.0% ±1.0% ±1.0% ±1.0% LOAD REGULATION ±.0% ±.0% ±.0% ±.0% SETUP, RISE TIME < 800ms, < ms / 30VAC at full load HOLD UP TIME (Typ.) > 3ms / 30VAC; >16ms / 115VAC at full load VOLTAGE RANGE 88 ~ 64VAC; 14 ~ 370VDC Derating may apply in low input voltage. Please check the derating curve for more details. FREQUENCY RANGE 47Hz~63Hz POWER FACTOR (Typ.) < 0.9 / 30VAC; < 0.98 / 115VAC at full load EFFICIENCY (Typ.) 87% 87% 88% 87% AC CURRENT (Typ.) 1.1 A / 115VAC; 0.55A / 30VAC INRUSH CURRENT (Typ.) COLD START 30A / 115VAC; 60A / 30VAC LEAKAGE CURRENT <1mA / 30VAC OVER LOAD PROTECTION OVER VOLTAGE PROTECTION OVER TEMPERATURE PROTECTION WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. / HUMIDITY TEMP. COEFFICIENT VIBRATION > 10% rated output power Protection type: Constant current limiting, recovers automatically after fault condition is removed. 115% ~ 150% rated output voltage Protection type: latch-off mode C ± 10 C (RTH) detect on heat sink of power transistor Protection type: Shut down overvoltage, re-power on to recover -0 ~ +70 C (Refer to output load derating curve) 0 ~ % RH non-condensing - ~ +85 C; 10 ~ 95% RH ±0.03% / C (0 ~ 50 C) 10 ~ 500Hz, G 10min. / 1cycle, 60 min. each long X,Y, Z axes SAFETY STANDARDS UL508, TUV EN :006+A11, UL1310 NEC class compliant WITHSTAND VOLTAGE I/P-O/P: 44DC I/P-FG: 11DC 1 minute ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG: M Ohms/500VDC EMI CONDUCTION & RADIATION EN550:006 Class B HARMONIC CURRENT EN60-3-:006 Class A, EN60-3-3: 1995+A1: 001+A: 005 EMS IMMUNITY EN6104-3:000, EN5504:1998+A1:001+A:003 light industry level, criteria A The power supply is considered a component which will installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. Signal Relay contact (4VDC / 1A, 10VAC / 1A) MTBF 10.4K Hrs MIL-HDBK-17F DIMENSION 55xx99 mm (WxHxD) PACKING 0.4Kg/4 pcs. / 10.8Kg CONNECTION l/p 3 poles, 0/P: 6 poles screw DIN terminal COOLING Free air convection All parameters NOT specially mentioned are measured at 30V AC input, rated load and 5 C of ambient temperature. *Not included in UL E

19 PSC-96 Series Mechanical Specification Unit : mm / inch Terminal Pin. No Assign. (TB1) 1 FG AC/N 3 AC/L Terminal Pin. No Assign. (TB) 1, DC +V 3,4 DC -V 5,6 RELAY CONTACT Block Diagram I/P EMI FILTER & RECTIFIERS PFC POWER SWITCHING RECTIFIERS & FILTER +V -V O.C.P. O.L.P. O.V.P. O.L.P. DETECTION PWM&PFC CONTROL O.V.P. Relay Contact O.T.P. Contact Close Contact Open Contact Ratings (max.) When the output voltage reaches the adjusted output voltage When the output voltage drop below % rated output voltage 30V / 1A resistive load Derating Curve Load V.S Temp. Load V.S I/P Voltage Ta=5 C VAC Ambient Temperature ( C) Input Voltage(VAC) 60Hz Note: All dimensions are in millimeters, to convert to inches multiply by

20 Compact Single Phase Power Supply (PSC) E0541 Features: Universal AC input (88-64V AC) Installed on DIN rail TS-35 / 7.5 or 15 Built-in active PFC function, PF > % peak load capability % full load burn-in test Protection: SCP, OLP, OVP, OTP Two selectable peak load modes Built-in Relay contact Built-in Remote ON / OFF function 3 years warranty UL W DIN Rail Power Supply Cat. No. Phases Output Tol. Ripple & Efficiency NOTES V DC A % Noise PSC V DC 6.3A ±1% mvp-p 87% PSC V DC 3.A ±1% 480 mvp-p 87% W DIN Rail Power Supply Cat. No. Phases Output Tol. Ripple & Efficiency NOTES V DC A % Noise PSC V DC 10A ±1% 150 mvp-p 91% PSC V DC 5A ±1% 300 mvp-p 9% 480W DIN Rail Power Supply Cat. No. Phases Output Tol. Ripple & Efficiency NOTES V DC A % Noise PSC V DC 0A ±1% mvp-p 93% PSC V DC 10A ±1% 480 mvp-p 94% 0A DIN Rail Redundancy Module Cat. No. Phases Output Input NOTES V DC A VDC A PSC-RM0 1 4V DC 0A 4VDC x0a 0

21 SPECIFICATIONS PSC-151 Series Terminal (TB1) Pin NO. 1 3 Assignment FG AC/L AC/N Terminal (TB) Pin NO. Assignment 1 DC+ DC- 3 INH+ 4 INH- 5,6 Relay Contact Universal Input: Connection Input: Connection Output: Size (WxHxD): Packaging: Switch No. Assignment SW NO. SW1 SW Assignment PEAK LOAD SETTING REMOTE ON/OFF SETTING PSC-41 Series Terminal (TB1) Pin NO. 1 3 Assignment FG AC/L AC/N Terminal (TB) Pin NO. Assignment 1 DC+ DC- 3 INH+ 4 INH- 5,6 Relay Contact Switch No. Assignment SW NO. SW1 SW Assignment PEAK LOAD SETTING REMOTE ON/OFF SETTING Universal Input: Connection Input: Connection Output: Size (WxHxD): Packaging: PSC-481 Series Terminal (TB1) Pin NO. 1 3 Assignment FG AC/L AC/N Terminal (TB) Pin NO. Assignment 1-3 DC+ 4-6 DC ,10 INH+ INH- Signal Switch No. Assignment SW NO. SW1 SW Assignment PEAK LOAD SETTING REMOTE ON/OFF SETTING Universal Input: Connection Input: Connection Output: Size (WxHxD): Packaging: PSC-RM0 Terminal Pin. No Assignment (TB1) 1 3,4 5 6 Vout+ Vout- Vin- Vin B+ Vin A+ Terminal Pin. No Assignment (TB) Alarm B1 Alarm B Alarm A1 Alarm A Input: Connection Input: Connection Output: Size (WxHxD): Packaging: 1

22 PSC-151 Series E0541 Features: Universal AC input (88-64V AC) Installed on DIN rail TS-35 / 7.5 or 15 Built-in active PFC function, PF > % peak load capability % full load burn-in test Protection: SCP, OLP, OVP, OTP Two selectable peak load modes Built-in Relay contact Built-in Remote ON / OFF function 3 years warranty UL 508 INPUT PROTECTION ENVIRONMENT SAFETY & EMC Cat. No. PSC-1514 PSC DC VOLTAGE 4V 48V RATED CURRENT 6.3A 3.A CURRENT RANGE 0~6.3A 0~3.A RATED POWER 150W 150W PEAK CURRENT 9.45A 4.8A PEAK POWER 5W (3sec.) 3 seconds or 0% duty cycle max. and the average output power should not exceed the rate power. RIPPLE & NOISE (max) mvp-p 480mVp-p Ripple & noise are measured at 0MHz of bandwidth by using a 1 twisted pair-wire terminated with a 0.1µF & 47µF parallel capacitor. VOLTAGE ADJ. RANGE -% ~ +8% -% ~ +8% VOLTAGE TOLERANCE ±1.0% ±1.0% Tolerance: includes set up tolerance, line regulation and load regulation. LINE REGULATION ±0.5% ±0.5% LOAD REGULATION ±1.0% ±1.0% SETUP, RISE TIME 700ms, 30ms / 30VAC / 115VAC at full load HOLD UP TIME (Typ.) 16ms / 30VAC; 16ms / 115VAC at full load VOLTAGE RANGE 88 ~ 64VAC; 14 ~ 373VDC Derating may apply in low input voltage. Please check the derating curve for more details. FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR(Typ.) 0.9 / 30VAC; 0.98 / 115VAC at full load EFFICIENCY (Typ.) 87% 87% AC CURRENT (Typ.).0A / 115VAC; 1.0A / 30VAC INRUSH CURRENT (Typ.) 33A / 115VAC; 65A / 30VAC LEAKAGE CURRENT <1mA/ VAC OVERLOAD PROTECTION 105% ~ 150% rated output power for 3 sec and then shutdown in O/P with auto-recovery. 150% or greater rated power or short circuit is constant current limiting. If O/P drops to % output then it auto-recover 5 times; if fault condition is not removed during auto recovery, the system will shut down and needs to be restarted to recover. OVER VOLTAGE 9 ~ 33V 56 ~ 65V Protection type: Latch-off mode, repower on to recover. OVER TEMPERATURE 95 ±5 C (TSW: detect on heatsink of power diode) Protection type: Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. / HUMIDITY TEMP. COEFFICIENT VIBRATION -10 ~ +70 C (Refer to derating curve) Installation clearance: mm from top, 0mm from bottom, 5mm from the left and right side are recommended when loaded permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended. 0 ~ 95% RH non-condensing - ~ +85 C, 10 ~ 95% RH ±0.03% / C (0 ~ 50 C) 10 ~ 500Hz, G 10min. / 1cycle, 60min. each along X, Y, Z axes SAFETY STANDARDS UL 508 / TUV EN WITHSTAND VOLTAGE I/P-O/P: 44VDC, I/P-FG: 11VDC, O/P-FG: 707VDC, O/P-: 707VDC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG: >M Ohms / 500VDC / 5 C / 70% RH EMI CONDUCTION & RADIATION EN550 (CISPR) Class B HARMONIC CURRENT EN60-3-, -3 EMS IMMUNITY Compliance to EN60-4-,3,4,5,6,8,11; ENV5004; EN5504; EN60-6-; (EN5008-); EN6104-3; heavy industry level; criteria A, MEET SEMI F47 The power supply is considered a component which will installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. RELAY. CONTACT RATINGS (max) 60VDC / 0.3A, 30VDC / 1A, 30VAC / 0.5A resistive load MTBF 6.7K HRS (MIL-HDBK-17F) DIMENSION 55.5x15.x99.8 mm (WxHxD) PACKING 0.7kg; 1pcs / 1.8kg COOLING Free air convection All parameters NOT specially mentioned are measured at 30VAC input, rated load and 5 C of ambient temperature.

23 PSC-151 Series Mechanical Specification Unit : mm / inch Terminal (TB1) Pin NO. 1 3 Assignment FG AC/L AC/N Terminal (TB) Pin NO. Assignment 1 DC+ DC- 3 INH+ 4 INH- 5,6 Relay Contact TB Relay Contact 99.8 Switch No. Assignment SW NO. SW1 SW Assignment PEAK LOAD SETTING REMOTE ON/OFF SETTING +V ADJ. + DC ON ON OFF SW1 SW TB1 3 Block Diagram I/P EMI FILTER & RECTIFIERS PFC POWER SWITCHING RECTIFIERS & FILTER +V -V O.C.P. FG O.L.P. O.L.P. O.L.P. AC DETECTION PWM & PFC CONTROL DETECTION MICRO O.V.P. O.T.P. Relay C REMOTE CONTROL INH+ INH- Relay Contact PEAK LOAD CONTROL Contact Close Contact Open Contact Ratings(max.) When the output voltage reaches the adjusted output voltage. When the output voltage drop below 45% rated output voltage. 30V/1A resistive load Note: All dimensions are in millimeters, to convert to inches multiply by

24 PSC-151 Series E0541 Peak Load SW1 ON (Mode1) Default setting I I-peak I-normal T-normal T-peak T-peak presents while the unit is working within 110%~150% Rating output power. See curve " B " for the variation in T-peak between output current and holdup time. If T-peak is more than the time setting in curve "B", the output current will drop to the constant current limit (I-normal) that is 105% rating power, meanwhile, I- normal and T-normal will be presenting. See curve "A" for the timing back to I-Peak of T-normal and this Mode can use for easy -stage battery charger. 0 T Peak Load SW OFF (Mode) I I-peak T-peak T-peak presents while the unit is working within 110%~150% Rating output power. See curve " B " for the variation in T-peak between output current and holdup time. If T-peak is more than the time setting in curve "B", the output current will be shut down for 3~4 sec, then auto-recovery. 0 3 ~ 4 sec T T-normal (Sec.) % 0% 30% % 50% 60% 70% 80% % CURVE A T-peak (Sec.) I-normal 110% 115% 10% 15% 130% 135% 1% 145% 150% I-peak CURVE B 4

25 PSC-151 Series Remote ON/OFF The PSU can be turned ON/OFF by using the "Remote Control" function. SW External Power Source I = 6 ~ 0mA SW OFF OFF ON ON INH+(3 PIN)/ INH-(4 PIN) SW ON (>.5V) SW OFF (<0.8V) SW ON (>.5V) SW OFF (<0.8V) Output Status ENABLE DISABLE DISABLE ENABLE (Default Setting) TB + +V ADJ. DC ON Relay Contact ON OFF SW1 SW Derating Curve For typ. 3sec Continuous (Vertical) Ambient Temperature ( C) AC=30 / 115VAC Output derating VS input Voltage VAC Input Voltage (V) 60Hz Ta=5 C 5

26 PSC-41 Series E0541 Features: Universal AC input (88-64V AC) High efficiency 9% and low power dissipation Installed on DIN rail TS-35 / 7.5 or 15 Built-in active PFC function, PF > % peak load capability % full load burn-in test Protection: SCP, OLP, OVP, OTP Two selectable peak load modes Built-in Relay contact Built-in Remote ON / OFF function 3 years warranty UL 508 INPUT PROTECTION ENVIRONMENT SAFETY & EMC Cat. No. PSC-414 PSC-4148 DC VOLTAGE 4V 48V RATED CURRENT 10A 5A CURRENT RANGE 0~10A 0~5A RATED POWER W W PEAK CURRENT 15A 7.5A PEAK POWER 360W (3sec.) Two selectable peak load modes 3 seconds or 0% duty cycle Max. The average output power should not exceed the rate power. RIPPLE & NOISE (max) 150mVp-p 300mVp-p Ripple & noise are measured at 0MHz of bandwidth by using a 1 twisted pair-wire terminated with a 0.1µF & 47µF parallel capacitor. VOLTAGE ADJ. RANGE -% ~ +8% -% ~ +8% VOLTAGE TOLERANCE ±1.0% ±1.0% Tolerance: includes set up tolerance, line regulation and load regulation. LINE REGULATION ±0.5% ±0.5% LOAD REGULATION ±1.0% ±1.0% SETUP, RISE TIME 700ms, 30ms / 30VAC / 115VAC at full load HOLD UP TIME (Typ.) 0ms / 30VAC; 0ms / 115VAC at full load VOLTAGE RANGE 88 ~ 64VAC; 14 ~ 373VDC Derating may apply in low input voltage. Please check the derating curve for more details. FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) 0.96 / 30VAC; 0.96 / 115VAC at full load EFFICIENCY (Typ.) 91% 9% AC CURRENT (Typ.).6A / 115VAC; 1.3A / 30VAC INRUSH CURRENT (Typ.) 33A / 115VAC; 65A / 30VAC LEAKAGE CURRENT <1mA/ VAC OVERLOAD 105% ~ 150% rated output power for 3 sec and then shutdown in O/P with auto-recovery. 150% or greater rated power or short circuit is constant current limiting. If O/P drops to % output then it auto-recover 5 times; if fault condition is not removed during auto recovery, the system will shut down and needs to be restarted to recover. OVER VOLTAGE 8 ~ 33V 56 ~ 65V Protection type: Shut down O/P voltage with auto-recovery OVER TEMPERATURE 95 ±5 C (TSW: detect on heatsink of power diode) Protection type: Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. / HUMIDITY TEMP. COEFFICIENT VIBRATION -5 ~ +70 C (Refer to output load derating curve) Installation clearances: mm on top, 0mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended. 0 ~ 95% RH non-condensing - ~ +85 C; 10 ~ 95% RH ±0.03% C (0 ~ 50 C) 10 ~ 500Hz, G 10min. / 1cycle, 60 min. each long X,Y, Z axes SAFETY STANDARDS UL508, TUV EN WITHSTAND VOLTAGE I/P-O/P: 44VDC I/P-FG11VDC O/P-F/G: 707VDC O/P-: 707VDC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG: > M Ohms / 500VDC / 5 C / 70% RH EMI CONDUCTION & RADIATION EN550:006 Class B HARMONIC CURRENT EN60-3-: 006 Class A, ENG0-3-3: A1: 001+A: 005 EMS IMMUNITY EN6104-3: 000, EN5504: 1998+A1: 001+A: 003 light industry level, criteria A The power supply is considered a component which will installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. RELAY CONTACT RATINGS (max) MTBF DIMENSION PACKING COOLING 60VDC / 0.3A, 30VDC / 1A, 30VAC / 0.5A resistive load 57K HRS (MIL-HDBK-17F) 65.8x15.x117.7 mm (WxHxD) 0.9kg; 1pcs / 1.8kg Free air convection All parameters NOT specially mentioned are measured at 30VAC input, rated load and 5 C of ambient temperature. 6

27 PSC-41 Series Mechanical Specification Unit : mm / inch Terminal (TB1) Pin NO. 1 3 Assignment FG AC/L AC/N Terminal (TB) Pin NO. Assignment 1 DC+ DC- 3 INH+ 4 INH- 5,6 Relay Contact TB Relay Contact Switch No. Assignment SW NO. SW1 SW Assignment PEAK LOAD SETTING REMOTE ON/OFF SETTING +V ADJ. + DC ON ON OFF SW1 SW TB1 Block Diagram I/P EMI FILTER & RECTIFIERS ACTIVE INRUSH CURRENT LIMITING PFC POWER SWITCHING RECTIFIERS & FILTER +V -V O.C.P. FG O.L.P. O.L.P. AC DETECTION PFC CONTROL PWM POWER CONTROL DETECTION MICRO O.V.P. O.T.P. Relay Contact REMOTE CONTROL INH+ INH- PEAK LOAD CONTROL Relay Contact Contact Close When the output voltage reaches the adjusted output voltage. Contact Open When the output voltage drop below 45% rated output voltage. Contact Ratings(max.) 30V/1A resistive load Note: All dimensions are in millimeters, to convert to inches multiply by

28 PSC-41 Series E0541 Peak Load SW1 ON (Mode1) Default setting I I-peak I-normal T-normal T-peak T-peak presents while the unit is working within 110%~150% Rating output power. See curve " B " for the variation in T-peak between output current and holdup time. If T-peak is more than the time setting in curve "B", the output current will drop to the constant current limit (I-normal) that is 105% rating power, meanwhile, I- normal and T-normal will be presenting. See curve "A" for the timing back to I-Peak of T-normal and this Mode can use for easy -stage battery charger. 0 T Peak Load SW OFF (Mode) I I-peak T-peak T-peak presents while the unit is working within 110%~150% Rating output power. See curve " B " for the variation in T-peak between output current and holdup time. If T-peak is more than the time setting in curve "B", the output current will be shut down for 3~4 sec, then auto-recovery. 0 3 ~ 4 sec T T-normal (Sec.) % 0% 30% % 50% 60% 70% 80% % CURVE A T-peak (Sec.) I-normal 110% 115% 10% 15% 130% 135% 1% 145% 150% I-peak CURVE B 8

29 PSC-41 Series Remote ON/OFF The PSU can be turned ON/OFF by using the "Remote Control" function. TB SW External Power Source I = 6 ~ 0mA SW OFF OFF ON ON INH+(3 PIN)/ INH-(4 PIN) SW ON (>.5V) SW OFF (<0.8V) SW ON (>.5V) SW OFF (<0.8V) Output Status ENABLE DISABLE DISABLE ENABLE (Default Setting) + +V ADJ. DC ON ON OFF SW1 SW Derating Curve For typ. 3sec Continuous (Vertical) Ambient Temperature ( C) AC=30 / 115VAC Output derating VS input Voltage VAC Input Voltage(V)60Hz Ta=5 C 9

30 PSC-481 Series E0541 Features: Universal AC input (88-64V AC) Installed on DIN rail TS-35 / 7.5 or 15 Built-in active PFC function, PF > % peak load capability Protection: SCP, OLP, OVP, OTP Two selectable peak load modes Built-in (Open Collector Signal) Built-in Remote ON / OFF function 3 years warranty UL 508 INPUT PROTECTION ENVIRONMENT SAFETY & EMC Cat. No. PSC-4814 PSC DC VOLTAGE 4V 48V RATED CURRENT 0A 10A CURRENT RANGE 0~0A 0~10A RATED POWER 480W 480W PEAK CURRENT 30A 15A PEAK POWER 70W (3sec.) Two selectable peak load modes 3 seconds or 0% duty cycle Max. The average output power should not exceed the rate power. RIPPLE & NOISE (max) mvp-p 480mVp-p Ripple & noise are measured at 0MHz of bandwidth by using a 1 twisted pair-wire terminated with a 0.1µF & 47µF parallel capacitor. VOLTAGE ADJ. RANGE -5% ~ +5% VOLTAGE TOLERANCE ±1.0% ±1.0% Tolerance: includes set up tolerance, line regulation and load regulation. LINE REGULATION ±0.5% ±0.5% LOAD REGULATION ±1.0% ±1.0% SETUP, RISE TIME 800ms, ms / 30VAC / 115VAC at full load HOLD UP TIME (Typ.) 16ms / 30VAC; 16ms / 115VAC at full load VOLTAGE RANGE 88 ~ 64VAC; 14 ~ 373VDC Derating may apply in low input voltage. Please check the derating curve for more details. FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) 0.96 / 30VAC / 115VAC at full load EFFICIENCY (Typ.) 93% 94% AC CURRENT (Typ.) 5.0A / 115VAC;.5A / 30VAC INRUSH CURRENT (Typ.) 33A / 115VAC; 65A / 30VAC LEAKAGE CURRENT < 1mA/ VAC OVERLOAD 105% ~ 150% rated output power for 3 sec and then shutdown in O/P with auto-recovery. 150% or greater rated power or short circuit is constant current limiting. If O/P drops to % output then it auto-recover 5 times; if fault condition is not removed during auto recovery, the system will shut down and needs to be restarted to recover. OVER VOLTAGE 9 ~ 33V 56 ~ 65V Protection type: Latch-off mode. OVER TEMPERATURE 95 ±5 C (TSW: detect on heatsink of power diode) Protection type: Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. WORKING HUMIDITY STORAGE TEMP. / HUMIDITY TEMP. COEFFICIENT VIBRATION -0 ~ +70 C (Refer to output load derating curve) Installation clearance: mm from top, 0mm from the left and right side are recommended when loaded permanently with full power. In case the adjacent device is a heat sorce, 15mm clearance is recomended. 0 ~ 95% RH non-condensing - ~ +85 C; 10 ~ 95% RH ±0.03% C (0 ~ 50 C) 10 ~ 500Hz, G 10min. / 1cycle, 60 min. each long X,Y, Z axes SAFETY STANDARDS UL 508 / EN WITHSTAND VOLTAGE I/P-O/P: 44VDC, I/P-FG: 11VDC, O/P-FG: 707VDC, O/P-: 707VDC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG: >M Ohms / 500VDC / 5 C / 70% RH EMI CONDUCTION & RADIATION EN 550 (CISPR), EN HARMONIC CURRENT EN60-3-, -3-3 EMS IMMUNITY IEC 60-4-, 3, 4, 5, 6, 8, 11; EN ; EN The power supply is considered a component which will installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. RELAY CONTACT RATINGS (max) DIMENSION PACKING 60VDC / 0.3A, 30VDC / 1A, 30VAC / 0.5A resistive load 86.3x14.8x13.4 mm (WxHxD) 1.45kg; 8pcs / 1kg All parameters NOT specially mentioned are measured at 30VAC input, rated load and 5 C of ambient temperature. 30

31 PSC-481 Series Mechanical Specification Unit : mm / inch Terminal (TB1) Pin NO. 1 3 Assignment FG AC/L AC/N Terminal (TB) Pin NO. Assignment 1-3 DC+ 4-6 DC ,10 INH+ INH- Singal TB Switch No. Assignment SW NO. SW1 SW Assignment PEAK LOAD SETTING REMOTE ON/OFF SETTING +V ADJ. + DC ON ON OFF SW1 SW 14.8 TB1 1 3 Block Diagram I/P EMI FILTER & RECTIFIERS ACTIVE inrush CURRENT LIMITING PFC POWER SWITCHING RECTIFIERS & FILTER +V -V O.C.P. FG O.L.P. O.L.P. AC DETECTION PFC CONTROL PWM POWER CONTROL DETECTION MICRO O.V.P. O.T.P. Singal REMOTE CONTROL INH+ INH- PEAK LOAD CONTROL Relay Contact Contact Ratings(max.) CTR : MIN. 50% at IF = 5mA, VCE = 5V Isolation Voltage Between input and output Viso = 3750Vrms Note: All dimensions are in millimeters, to convert to inches multiply by

32 PSC-481 Series E0541 Peak Load SW1 ON (Mode1) Default setting I I-peak I-normal T-normal T-peak T-peak presents while the unit is working within 110%~150% Rating output power. See curve " B " for the variation in T-peak between output current and holdup time. If T-peak is more than the time setting in curve "B", the output current will drop to the constant current limit (I-normal) that is 105% rating power, meanwhile, I- normal and T-normal will be presenting. See curve "A" for the timing back to I-Peak of T-normal and this Mode can use for easy -stage battery charger. 0 T Peak Load SW OFF (Mode) I I-peak T-peak T-peak presents while the unit is working within 110%~150% Rating output power. See curve " B " for the variation in T-peak between output current and holdup time. If T-peak is more than the time setting in curve "B", the output current will be shut down for 3~4 sec, then auto-recovery. 0 3 ~ 4 sec T T-normal (Sec.) % 0% 30% % 50% 60% 70% 80% % CURVE A T-peak (Sec.) I-normal 110% 115% 10% 15% 130% 135% 1% 145% 150% I-peak CURVE B 3

33 PSC-481 Series Remote ON/OFF The PSU can be turned ON/OFF by using the "Remote Control" function. TB SW External Power Source I = 6 ~ 0mA SW OFF OFF ON ON INH+(3 PIN)/ INH-(4 PIN) SW ON (>.5V) SW OFF (<0.8V) SW ON (>.5V) SW OFF (<0.8V) Output Status ENABLE DISABLE DISABLE ENABLE (Default Setting) + +V ADJ. DC ON ON OFF SW1 SW Derating Curve For typ. 3sec Continuous (Vertical) Ambient Temperature ( C) AC=30 / 115VAC Output derating VS input Voltage VAC Input Voltage(V)60Hz Ta=5 C 33

34 PSC-RM0 Specifications Features: Suitable for redundant operation of 4V system Installed on DIN Rail TS35 / 7.5 or 15 Relay contact signal output and LED indicator for input failure alarm Cooling by free air convection 3 year warranty INPUT PROTECTION ENVIRONMENT SAFETY & EMC Cat. No. PS-RDN0 REVERSE VOLTAGE (max.) 30V CURRENT (max.) 0A VOLTAGE DROP 0.5V LED INDICATORS Two green LED s indicating each input is OK or fail INPUT VOLTAGE RANGE NUMBER OF INPUTS INPUT CURRENT (max.) INPUT VOLTAGE ALARM RELAY CONTACT RATING (max.) WORKING TEMP. WORKING HUMIDITY STORAGE TEMP., HUMIDITY VIBRATION MOUNTING 1 ~ 8V Two 0A per input When input is 0V (±5%) or 30V (±5%) relay contacts 30VDC, 1A -0 ~ +70 C 0 ~ % RH non-condensing - ~ +85 C, 10 ~ 95% RH 10 ~ 500Hz, G 10min./1cycle, 60 min. each long X,Y, Z axes Compliance to IEC WITHSTAND VOLTAGE Terminal- Chassis: 0.5KVAC, Relay Contacts- Terminal: 0.5KVAC ISOLATION RESISTANCE Terminal- Chassis: M Ohms / 500VDC (5 C; 70% RH) EMI CONDUCTION & RADIATION Compliance to EN550 (CISPR) Class B EMS IMMUNITY Compliance to EN60-4-,3,4,5,6,8; ENV5004; heavy industry level; criteria A, MTBF 996.8Khrs min. MIL-HDBK-17K (5 C) DIMENSION 55.5x15.xmm (WxHxD) PACKING 0.45Kg; 0pcs / 11Kg / 1.9CUFT All parameters NOT specially mentioned are measured at 4V DC input, rated load and 5 C of ambient temperature. Block Diagram Vout+ Vin/Vout- Vin A+ RELAY B RELAY A + + Alarm A 34