NI 6238/6239 Specifications

Size: px
Start display at page:

Download "NI 6238/6239 Specifications"

Transcription

1 NI 6238/6239 Specifications Specifications listed below are typical at 25 C unless otherwise noted. Analog Input Number of channels... 8 differential current inputs Ground reference... AI GND ADC resolution... 6 bits DNL... No missing codes guaranteed INL... Refer to the AI Absolute Accuracy Table Sampling rate Maximum ks/s Minimum... No minimum Timing accuracy ppm of sample rate Timing resolution ns Input current during overvoltage condition...±20 ma max/ai pin Overcurrent protection...±40 ma max Overvoltage protection 2 (AI x+ or AI x with respect to AI GND) Device on...±25 V for up to two AI pins Device off...±5 V for up to two AI pins Input coupling... DC Input range... ±20 ma Maximum working voltage for analog inputs... Refer to the Maximum Working Voltage section Input impedance (AI+ to AI ) Ω ±0% in parallel with 00 pf Maximum input impedance Ω (at 55 C) Input bias current... ±00 pa Small signal bandwidth ( 3 db) khz Input FIFO size... 4,095 samples Scan list memory... 4,095 entries Data transfers... DMA (scatter-gather), interrupts, programmed I/O Any voltage applied resulting in current flowing above 40 ma can damage the device permanently. 2 This overvoltage protection triggers after the overcurrent protection is in effect.

2 Typical Performance Graphs Normalized Signal Amplitude (db) CMRR (db) AI <0..7> Small Signal Bandwidth 4 k 0 k 00 k 000 k 0,000 k Frequency (Hz) AI x CMRR to Earth Ground k 0 k 00 k Frequency (Hz) Analog Output Number of channels...2 current outputs Ground reference...ao GND DAC resolution...6 bits Maximum update rate channel ks/s 2 channels ks/s per channel Power-on glitch... None Output FIFO size... 8,9 samples shared among channels used Data transfers... DMA (scatter-gather), interrupts, programmed I/O AO waveform modes: Non-periodic waveform Periodic waveform regeneration mode from onboard FIFO Periodic waveform regeneration from host buffer including dynamic update External power supply VDC External power supply consumption ma max Internal voltage drop... 3 V max Maximum resistive load... Up to kω with 24 V power supply connected User- Provided Power Supply + AO Power Supply Pin Internal Voltage Drop User- Provided Load AO GND AO x User-Provided AO GND Figure. Analog Output Protection... Open and short circuit Slew rate ma/μs Calibration (AI and AO) Recommended warm-up time... 5 minutes Calibration interval... year DAC Timing accuracy...50 ppm of sample rate Timing resolution...50 ns Output range...0 to 20 ma Output coupling...dc Power-on state...0 ma Refer to Figure for more details. NI 6238/6239 Specifications 2 ni.com

3 AI Absolute Accuracy Table Nominal Range Positive Full Scale Negative Full Scale Residual Gain Error (ppm of Reading) Gain Tempco (ppm/ C) Reference Tempco Residual Offset Error (ppm of Range) Offset Tempco (ppm of Range/ C) INL Error (ppm of Range) Random Noise, σ (μarms) Absolute Accuracy at Full Scale (μa) Sensitivity 2 (μa) AbsoluteAccuracy = Reading (GainError) + Range (OffsetError) + NoiseUncertainty GainError = ResidualAIGainError + GainTempco (TempChangeFromLastInternalCal) + ReferenceTempco (TempChangeFromLastExternalCal) OffsetError = ResidualAIOffsetError + OffsetTempco (TempChangeFromLastInternalCal) + INL_Error NoiseUncertainty = RandomNoise For a coverage factor of 3 σ and averaging 00 points. 00 Absolute accuracy at full scale on the analog input channels is determined using the following assumptions: TempChangeFromLastExternalCal = 0 C TempChangeFromLastInternalCal = C number_of_readings = 00 CoverageFactor = 3 σ For example, on the 20 ma range, the absolute accuracy at full scale is as follows: GainError = 595 ppm + 35 ppm + 5 ppm 0 GainError = 680 ppm OffsetError = 00 ppm + 79 ppm + 76 ppm OffsetError = 255 ppm NoiseUncertainty μa 3 = NoiseUncertainty = 73.2 na 00 AbsoluteAccuracy = 20 ma (GainError) + 20 ma (OffsetError) + NoiseUncertainty AbsoluteAccuracy = 8.8 μa 2 Sensitivity is the smallest current change that can be detected. It is a function of noise. Accuracies listed are valid for up to one year from the device external calibration. National Instruments Corporation 3 NI 6238/6239 Specifications

4 AO Absolute Accuracy Table Positive Full Scale (A) Nominal Range Negative Full Scale (A) Residual Gain Error (% of Reading) Gain Tempco (ppm/ C) Reference Tempco Residual Offset Error (% of Range) Offset Tempco (ppm of Range/ C) INL Error (ppm of Range) Random Noise (μa) Absolute Accuracy at Full Scale (μa) Absolute Accuracy at full scale numbers is valid immediately following internal calibration and assumes the device is operating within 0 C of the last external calibration. Accuracies listed are valid for up to one year from the device external calibration. NoiseUncertainty = RandomNoise 3 AbsoluteAccuracy = OutputValue (GainError) + Range (OffsetError) + NoiseUncertainty GainError = ResidualGainError + GainTempco (TempChangeFromLastInternalCal) + ReferenceTempco (TempChangeFromLastExternalCal) OffsetError = ResidualOffsetError + AOOffsetTempco (TempChangeFromLastInternalCal) + INL_Error NI 6238/6239 Specifications 4 ni.com

5 Digital I/O/PFI Static Characteristics Number of channels... 0 total Input... 6 (PFI <0..5>/P0.<0..5>) Output... 4 (PFI <6..9>/P.<0..3>) Direction control... Fixed, lines are unidirectional Digital Output (Port ) Number of channels...4 Ground reference...p.gnd Digital output type NI DO source NI DO sink PFI/Port 0/Port Functionality PFI <0..5>/P0.<0..5>... Static digital input, timing input PFI <6..9>/P.<0..3>... Static digital output, timing output Timing output sources... Many AI, AO, counter, timing signals Debounce filter settings ns, μs, 2.54 ms, disable; high and low transitions; selectable per input Digital Input (Port 0) Number of channels... 6 Ground reference... Input voltage range... 0 to 30 V Minimum pulse width for timing signal μs Logic 0 level... 0 to 4 V Logic level... 0 to 30 V Minimum input impedance kω Typical input current... 7 ma at 24 V input 2.5 ma at 8 V input Maximum input current... 9 ma Propagation delay Low to high ns, typ High to low ns, typ Refer to Figures 2 and 3. National Instruments Corporation 5 NI 6238/6239 Specifications

6 Figures 2 and 3 show P0.<0..5> and P.<0..3> on the NI 6238 and NI 6239 devices, respectively. P.VCC P.0 P.<0..3> Digital Isolators P. P.GND P.GND P0.0 Figure 2. NI 6238 Digital I/O Connections P.VCC P.0 P.GND P. P.<0..3> P.GND Digital Isolators P.GND P0.0 Figure 3. NI 6239 Digital I/O Connections NI 6238/6239 Specifications 6 ni.com

7 Max external supply voltage (P.VCC) V On state saturation voltage....6 V maximum at 350 ma Off state leakage μa Maximum current ma for each line for simultaneous usage 350 ma for single line usage Minimum pulse width for timing signal NI 6238 (source output)... 5 μs NI 6239 (sink output) μs Propagation delay NI 6238 (source output) Open to close μs Close to open μs NI 6239 (sink output) Open to close μs Close to open μs General-Purpose Counter/Timers Number of counter/timers... 2 Resolution bits Counter measurements... Edge counting, pulse, semi-period, period, two-edge separation Position measurements... X, X2, X4 quadrature encoding with Channel Z reloading; two-pulse encoding Output applications... Pulse, pulse train with dynamic updates, frequency division, equivalent time sampling Internal base clocks MHz, 20 MHz, 0. MHz External base clock frequency... 0 MHz to 20 MHz Base clock accuracy ppm Inputs... Gate, Source, HW_Arm, Aux, A, B, Z, Up_Down Routing options for inputs... Any input PFI, RTSI, PXI_TRIG, PXI_STAR, many internal signals FIFO...2 samples Data transfers...dedicated scatter-gather DMA controller for each counter/timer; interrupts; programmed I/O Frequency Generator Number of channels... Base clocks...0 MHz, 00 khz Divisors... to 6 Base clock accuracy...50 ppm Output can be available on any output PFI or RTSI terminal. Phase-Locked Loop (PLL) Number of PLLs... Reference signal...pxi_star, PXI_CLK0, RTSI <0..7> Output of PLL...80 MHz Timebase; other signals derived from 80 MHz Timebase including 20 MHz and 00 khz Timebases External Digital Triggers Source...Any input PFI, RTSI, PXI_TRIG, PXI_STAR Polarity...Software-selectable for most signals Analog input function...start Trigger, Reference Trigger, Pause Trigger, Sample Clock, Convert Clock, Sample Clock Timebase Analog output function...start Trigger, Pause Trigger, Sample Clock, Sample Clock Timebase Counter/timer functions...gate, Source, HW_Arm, Aux, A, B, Z, Up_Down National Instruments Corporation 7 NI 6238/6239 Specifications

8 Device-To-Device Trigger Bus PCI devices...rtsi <0..7> PXI devices...pxi_trig <0..7>, PXI_STAR Output selections...0 MHz Reference Clock; frequency generator output; many internal signals Debounce filter settings...25 ns, μs, 2.54 ms, disabled; high and low transitions; selectable per input Bus Interface PCI or PXI V or 5 V signal environment PXI-6238/6239 devices can be installed in PXI slots or PXI Express hybrid slots. DMA channels...4, analog input, analog output, counter/timer 0, counter/timer Power Requirements Current draw from bus during no-load condition +5 V A +2 V...20 ma Current draw from bus during AI and AO overvoltage condition +5 V A +2 V...20 ma Physical Requirements Printed circuit board dimensions NI PCI-6238/ cm 5.5 cm (3.8 in. 6. in.) NI PXI-6238/ Standard 3U PXI Weight NI PCI-6238/ g (3.6 oz) NI PXI-6238/ g (5. oz) I/O connector...37-pin D-SUB In other sections of this document, RTSI refers to RTSI <0..7> for PCI devices or PXI_TRIG <0..7> for PXI devices. NI 6238/6239 Specifications 8 ni.com

9 Maximum Working Voltage Channel-to-earth ground 2 Continuous Vrms/60 VDC Measurement Category I 3 Withstand Vrms/200 VDC, verified by a 5 s dielectric withstand test Channel-to-bus 4 Continuous Vrms/60 VDC Measurement Category I 4 Withstand Vrms/950 VDC, verified by a 5 s dielectric withstand test Analog channel to AI GND/AO GND (in Figure 4, V a V b )... V, Measurement Category I 3 Digital channel to P.GND/ (in Figure 4, V c V d or V e V f ) V, Measurement Category I 3 Caution This device is rated for Measurement Category I and the voltage across the isolation barrier is limited to no greater than 30 Vrms/42.4 V pk /60 VDC continuous. Do not use for measurements within Categories II, III, or IV. Figure 4 illustrates the maximum working voltage specifications. V a V b V c V d V e V f V g V h AI x/ao x AI GND/AO GND PFI <0..5> PFI <6..9> P.GND Figure 4. NI 6238/6239 Maximum Working Voltage Environmental Operating temperature...0 to 55 C Storage temperature to 70 C Humidity...0 to 90% RH, noncondensing Maximum altitude...2,000 m PXI/PCI-Bus Bus Pollution Degree (indoor use only)...2 Maximum working voltage refers to the signal voltage plus the common-mode voltage. 2 In Figure 4, V a V h, V c V h, and V e V h. 3 Measurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live electrical supply system that powers equipment. This category is for measurements of voltages from specially protected secondary circuits. Such voltage measurements include signal levels, special equipment, limited-energy parts of equipment, circuits powered by regulated low-voltage sources, and electronics. 4 In Figure 4, V a V g, V c V g, and V e V g. National Instruments Corporation 9 NI 6238/6239 Specifications

10 Shock and Vibration (PXI Only) Operational shock...30 g peak, half-sine, ms pulse (Tested in accordance with IEC Test profile developed in accordance with MIL-PRF-28800F) Random vibration Operating...5 to 500 Hz, 0.3 g rms Nonoperating...5 to 500 Hz, 2.4 g rms (Tested in accordance with IEC Nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3.) Safety This product is designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: IEC 600-, EN-600- UL 600-, CAN/CSA-C22.2 No CE Compliance This product meets the essential requirements of applicable European Directives, as amended for CE marking, as follows: 73/23/EEC; Low-Voltage Directive (safety) 89/336/EEC; Electromagnetic Compatibility Directive (EMC) Note Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column. Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of their life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers and National Instruments WEEE initiatives, visit ni.com/environment/weee.htm. Note For UL and other safety certifications, refer to the product label or visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column. Electromagnetic Compatibility This product is designed to meet the requirements of the following standards of EMC for electrical equipment for measurement, control, and laboratory use: EN 6326 EMC requirements; Minimum Immunity EN 550 Emissions; Group, Class A CE, C-Tick, ICES, and FCC Part 5 Emissions; Class A Note For EMC compliance, operate this device according to product documentation. NI 6238/6239 Specifications 0 ni.com

11 AI 0 AI + AI 2+ AI 3 AI GND AI 4 AI 5+ AI 6+ AI 7+ NC AO 0 AO GND PFI /P0. (Input) PFI 2/P0.2 (Input) PFI 4/P0.4 (Input) P.VCC PFI 7/P. (Output) PFI 9/P.3 (Output) AI 0+/CAL+ AI AI GND AI 2 AI 3+ AI 4+ AI 5 CAL AI 6 AI 7 NC AO PFI 0/P0.0 (Input) PFI 3/P0.3 (Input) PFI 5/P0.5 (Input) PFI 6/P.0 (Output) PFI 8/P.2 (Output) P.GND AI 0 AI + AI 2+ AI 3 AI GND AI 4 AI 5+ AI 6+ AI 7+ NC AO 0 AO GND PFI /P0. (Input) PFI 2/P0.2 (Input) PFI 4/P0.4 (Input) P.GND PFI 7/P. (Output) PFI 9/P.3 (Output) AI 0+/CAL+ AI AI GND AI 2 AI 3+ AI 4+ AI 5 CAL AI 6 AI 7 NC AO PFI 0/P0.0 (Input) PFI 3/P0.3 (Input) PFI 5/P0.5 (Input) PFI 6/P.0 (Output) PFI 8/P.2 (Output) P.VCC NC = No Connect Figure 5. NI 6238 Pinout NC = No Connect Figure 6. NI 6239 Pinout National Instruments Corporation NI 6238/6239 Specifications

12 National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents National Instruments Corporation. All rights reserved. 3794A-0 Jul06

NI 6230 Specifications

NI 6230 Specifications NI 6230 Specifications Specifications listed below are typical at 25 C unless otherwise noted. Analog Input Number of channels... 4 differential or 8singleended ADC resolution... 6 bits DNL... No missing

More information

NI 622x Specifications

NI 622x Specifications NI 622x Specifications Specifications listed below are typical at 25 C unless otherwise noted. Refer to the M Series User Manual for more information about NI 622x devices. Analog Input Number of channels

More information

NI 6124 Specifications

NI 6124 Specifications NI 6124 Specifications This document lists the specifications for the NI PXIe-6124. For the most current edition of this document, refer to ni.com/manuals. Refer to the DAQ Getting Started Guide for more

More information

M Series Data Acquisition: 16-Bit, 250 ks/s, 8 AI, 2 AO, 24 DIO Sourcing, Current Input/Output Bank Isolation

M Series Data Acquisition: 16-Bit, 250 ks/s, 8 AI, 2 AO, 24 DIO Sourcing, Current Input/Output Bank Isolation DEVICE SPECIFICATIONS NI 6238 M Series Data Acquisition: 16-Bit, 250 ks/s, 8 AI, 2 AO, 24 DIO Sourcing, Current Input/Output Bank Isolation The following specifications are typical at 25 C, unless otherwise

More information

Analog Input. DEVICE SPECIFICATIONS NI PXIe-4300

Analog Input. DEVICE SPECIFICATIONS NI PXIe-4300 DEVICE SPECIFICATIONS NI PXIe-4300 This document lists specifications for the NI PXIe-4300 module. These specifications are typical for the range of 0 C to 55 C unless otherwise stated. The system must

More information

M Series Data Acquisition: 16-Bit, 250 ks/s, 16 AI, 2 AO, 24 DIO Sinking, Voltage Input/Output Bank Isolation

M Series Data Acquisition: 16-Bit, 250 ks/s, 16 AI, 2 AO, 24 DIO Sinking, Voltage Input/Output Bank Isolation DEVICE SPECIFICATIONS NI 6233 M Series Data Acquisition: 16-Bit, 250 ks/s, 16 AI, 2 AO, 24 DIO Sinking, Voltage Input/Output Bank Isolation The following specifications are typical at 25 C, unless otherwise

More information

M Series Data Acquisition: 16-Bit, 250 ks/s, 4 AI, 4 AO, 6 DI, 4 DO, Current Input, Voltage Output, Bank Isolation

M Series Data Acquisition: 16-Bit, 250 ks/s, 4 AI, 4 AO, 6 DI, 4 DO, Current Input, Voltage Output, Bank Isolation DEVICE SPECIFICATIONS NI 6236 M Series Data Acquisition: 16-Bit, 250 ks/s, 4 AI, 4 AO, 6 DI, 4 DO, Current Input, Voltage Output, Bank Isolation The following specifications are typical at 25 C, unless

More information

NI 6356/6358 Specifications

NI 6356/6358 Specifications NI 6356/6358 Specifications Français Deutsch ni.com/manuals Specifications listed below are typical at 25 C unless otherwise noted. Refer to the X Series User Manual for more Analog Input Number of channels

More information

M Series Data Acquisition: 16-Bit, 250 ks/s, 8 AI, 4 AO, 6 DI, 4 DO, Voltage Input/Output, Bank Isolation

M Series Data Acquisition: 16-Bit, 250 ks/s, 8 AI, 4 AO, 6 DI, 4 DO, Voltage Input/Output, Bank Isolation DEVICE SPECIFICATIONS NI 6230 M Series Data Acquisition: 16-Bit, 250 ks/s, 8 AI, 4 AO, 6 DI, 4 DO, Voltage Input/Output, Bank Isolation The following specifications are typical at 25 C, unless otherwise

More information

NI 6143 Specifications

NI 6143 Specifications NI 6143 Specifications This document lists the I/O terminal summary and specifications for the NI PCI/PXI-6143. For the most current edition of this document, refer to ni.com/manuals. Refer to the DAQ

More information

NI 6013/6014 Family Specifications

NI 6013/6014 Family Specifications NI 6013/6014 Family Specifications This document lists the I/O terminal summary and specifications for the NI 6013/6014 family of devices. This family includes the following devices: NI PCI-6013 NI PCI-6014

More information

NI 6731/6733 Specifications

NI 6731/6733 Specifications NI 6731/6733 Specifications This document lists the specifications for the NI 6731/6733 analog output devices. The following specifications are typical at 25 C unless otherwise noted. Note With NI-DAQmx,

More information

Analog Characteristics

Analog Characteristics SPECIFICATIONS NI PXIe-4322 This document lists specifications for the NI PXIe-4322 module. These specifications are typical for the range of 0 C to 55 C unless otherwise stated. The system must be allowed

More information

NI DAQPad -6020E Family Specifications

NI DAQPad -6020E Family Specifications NI DAQPad -6020E Family Specifications This document lists the I/O terminal summary and specifications for the NI DAQPad-6020E family of devices. This family includes the following devices: NI DAQPad-6020E

More information

Industrial M Series Multifunction DAQ 16-Bit, ±10 V/±20 ma Analog I/O, 5 V/24 V Digital I/O

Industrial M Series Multifunction DAQ 16-Bit, ±10 V/±20 ma Analog I/O, 5 V/24 V Digital I/O Technical Sales (866) 531-6285 orders@ni.com Requirements and Compatibility Ordering Information Detailed Specifications Pinouts/Front Panel Connections For user manuals and dimensional drawings, visit

More information

Current ON state current ma minimum, 6 ma typical, 10 ma maximum OFF state current ma maximum

Current ON state current ma minimum, 6 ma typical, 10 ma maximum OFF state current ma maximum DEVICE SPECIFICATIONS NI 6624 This document lists the specifications for the NI PCI/PXI-6624 device. These specifications are typical at 25 C unless otherwise noted. Refer to the NI 6624 User Manual for

More information

SPECIFICATIONS PXIe channel, 16-bit, 400 ks/s/ch, Ch-Ch Isolated Analog Input Module. ni.com/manuals

SPECIFICATIONS PXIe channel, 16-bit, 400 ks/s/ch, Ch-Ch Isolated Analog Input Module. ni.com/manuals SPECIFICATIONS PXIe-4310 8-channel, 16-bit, 400 ks/s/ch, Ch-Ch Isolated Analog Input Module Français Deutsch ni.com/manuals This document lists specifications for the PXIe-4310 module. These specifications

More information

M Series Data Acquisition: 18-Bit, 500 ks/s, 16 AI, 24 DIO

M Series Data Acquisition: 18-Bit, 500 ks/s, 16 AI, 24 DIO DEVICE SPECIFICATIONS NI 6280 M Series Data Acquisition: 18-Bit, 500 ks/s, 16 AI, 24 DIO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6280,

More information

NI 6040E Family Specifications

NI 6040E Family Specifications NI 6040E Family Specifications This document lists the I/O terminal summary and specifications for the devices that make up the NI 6040E family of devices. This family includes the following devices: NI

More information

Analog Input SPECIFICATIONS NI 6320/6321/6323

Analog Input SPECIFICATIONS NI 6320/6321/6323 SPECIFICATIONS NI 6320/6321/6323 Français Deutsch ni.com/manuals Specifications listed below are typical at 25 C unless otherwise noted. Refer to the X Series User Manual for more information about NI

More information

NI 6023E/6024E/6025E Family Specifications

NI 6023E/6024E/6025E Family Specifications NI 6023E/6024E/6025E Family Specifications This document lists the I/O terminal summary and specifications for the devices that make up the NI 6023E/6024E/6025E family of devices. This family includes

More information

M Series Data Acquisition: 32 AI, 1.25 MS/s, 48 DIO

M Series Data Acquisition: 32 AI, 1.25 MS/s, 48 DIO DEVICE SPECIFICATIONS NI 6254 M Series Data Acquisition: 32 AI, 1.25 MS/s, 48 DIO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6254, refer

More information

X Series Data Acquisition: 16 AI, 250 ks/s, 16-Bit Resolution, ±10 V

X Series Data Acquisition: 16 AI, 250 ks/s, 16-Bit Resolution, ±10 V DEVICE SPECIFICATIONS NI 6320 X Series Data Acquisition: 16 AI, 250 ks/s, 16-Bit Resolution, ±10 V The following specifications are typical at 25 C, unless otherwise noted. For more information about the

More information

Input Characteristics. Measurement Range. SPECIFICATIONS NI PXIe-4357

Input Characteristics. Measurement Range. SPECIFICATIONS NI PXIe-4357 SPECIFICATIONS NI PXIe-4357 This document lists specifications for the NI PXIe-4357 module. These specifications are typical for the range of 0 C to 55 C unless otherwise stated. The system must be allowed

More information

Isolated 32 AI (16-Bit, 250 ks/s), 2 AO (250 ks/s), 8 DI, 8 DIO USB Multifunction I/O Device

Isolated 32 AI (16-Bit, 250 ks/s), 2 AO (250 ks/s), 8 DI, 8 DIO USB Multifunction I/O Device SPECIFICATIONS USB-6218 Isolated 32 AI (16-Bit, 250 ks/s), 2 AO (250 ks/s), 8 DI, 8 DIO USB Multifunction I/O Device These specifications apply to the USB-218 BNC and USB-6218 Spring Terminal. Definitions

More information

X Series Data Acquisition: 80 AI, 1.25 MS/s, 1 MS/s, 16-Bit Resolution, ±10 V, 24 DIO, 2 AO. ni.com/manuals

X Series Data Acquisition: 80 AI, 1.25 MS/s, 1 MS/s, 16-Bit Resolution, ±10 V, 24 DIO, 2 AO. ni.com/manuals DEVICE SPECIFICATIONS NI 6355 X Series Data Acquisition: 80 AI, 1.25 MS/s, 1 MS/s, 16-Bit Resolution, ±10 V, 24 DIO, 2 AO Français Deutsch 日本語한국어简体中文 ni.com/manuals The following specifications are typical

More information

X Series Data Acquisition: 2 MS/s/ch, 16 AI, 48 DIO, 4 AO

X Series Data Acquisition: 2 MS/s/ch, 16 AI, 48 DIO, 4 AO DEVICE SPECIFICATIONS NI 6368 X Series Data Acquisition: 2 MS/s/ch, 16 AI, 48 DIO, 4 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6368,

More information

NI PXI-4461 Specifications

NI PXI-4461 Specifications NI PXI-446 Specifications Analog Input Input Characteristics This document lists specifications for the NI PXI-446 Dynamic Signal Acquisition (DSA) device. These specifications are typical at 5 C unless

More information

16 AI (16-Bit, 250 ks/s), 4 DI, 4 DO USB Multifunction I/O Device

16 AI (16-Bit, 250 ks/s), 4 DI, 4 DO USB Multifunction I/O Device SPECIFICATIONS USB-6210 16 AI (16-Bit, 250 ks/s), 4 DI, 4 DO USB Multifunction I/O Device Definitions Warranted specifications describe the performance of a model under stated operating conditions and

More information

NI 6221 M Series Data Acquisition: 16-Bit, 250 ks/s, 16 AI, 24 DIO, 2 AO

NI 6221 M Series Data Acquisition: 16-Bit, 250 ks/s, 16 AI, 24 DIO, 2 AO DEVICE SPECIFICATIONS NI 6221 M Series Data Acquisition: 16-Bit, 250 ks/s, 16 AI, 24 DIO, 2 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI

More information

No missing codes guaranteed Refer to the AI Absolute Accuracy section. Sample rate

No missing codes guaranteed Refer to the AI Absolute Accuracy section. Sample rate DEVICE SPECIFICATIONS NI 6378 PXI Express, 3.5 MS/s/ch, 16 AI, 48 DIO, 4 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6378, refer to the

More information

M Series Data Acquisition: 80 AI, 1.25 MS/s, 24 DIO, 2 AO

M Series Data Acquisition: 80 AI, 1.25 MS/s, 24 DIO, 2 AO DEVICE SPECIFICATIONS NI 6255 M Series Data Acquisition: 80 AI, 1.25 MS/s, 24 DIO, 2 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6255,

More information

Specifications. PCI Bus. Analog Input Input Characteristics

Specifications. PCI Bus. Analog Input Input Characteristics Specifications A This appendix lists the specifications of the NI 6034E/6035E/6036E. These specifications are typical at 25 C unless otherwise noted. The first section provides the specifications for the

More information

16 AI (16-Bit, 400 ks/s), 2 AO (250 ks/s), Up to 32 DIO USB Multifunction I/O Device

16 AI (16-Bit, 400 ks/s), 2 AO (250 ks/s), Up to 32 DIO USB Multifunction I/O Device SPECIFICATIONS USB-6212 16 AI (16-Bit, 400 ks/s), 2 AO (250 ks/s), Up to 32 DIO USB Multifunction I/O Device These specifications apply to the USB-6212 BNC, USB-6212 Mass Termination, and USB-6212 Spring

More information

PXIe, 32 AI (16-Bit, 2 MS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module

PXIe, 32 AI (16-Bit, 2 MS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module SPECIFICATIONS PXIe-6363 PXIe, 32 AI (16-Bit, 2 MS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module Definitions Warranted specifications describe the performance of a model under stated operating conditions

More information

NI PXI/PCI-5411/5431 Specifications

NI PXI/PCI-5411/5431 Specifications NI PXI/PCI-5411/5431 Specifications NI PXI/PCI-5411 High-Speed Arbitrary Waveform Generator NI PXI/PCI-5431 Video Waveform Generator Analog Output This document lists the specifications for the NI PXI/PCI-5411

More information

M Series Data Acquisition: 18-Bit, 625 ks/s, 32 AI, 48 DIO, 4 AO

M Series Data Acquisition: 18-Bit, 625 ks/s, 32 AI, 48 DIO, 4 AO DEVICE SPECIFICATIONS NI 6289 M Series Data Acquisition: 18-Bit, 625 ks/s, 32 AI, 48 DIO, 4 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI

More information

NI PXI-2532 Specifications

NI PXI-2532 Specifications NI PXI-2532 Specifications 512-Crosspoint, 1-Wire Matrix This document lists specifications for the National Instruments PXI-2532 512-crosspoint, 1-wire matrix. All specifications are subject to change

More information

Specifications for the NI PXI/PCI-6552/6551

Specifications for the NI PXI/PCI-6552/6551 Specifications for the NI PXI/PCI-6552/6551 100/50 MHz Digital Waveform Generator/Analyzer Channel Characteristics These specifications are valid for the operating temperature range, unless otherwise noted.

More information

X Series Data Acquisition 2 MS/s/ch, 8 AI, 24 DIO, 2 AO

X Series Data Acquisition 2 MS/s/ch, 8 AI, 24 DIO, 2 AO DEVICE SPECIFICATIONS NI 6366 X Series Data Acquisition 2 MS/s/ch, 8 AI, 24 DIO, 2 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6366, refer

More information

Bus-Powered M Series Multifunction DAQ for USB - 16-Bit, up to 400 ks/s, up to 32 Analog Inputs, Isolation

Bus-Powered M Series Multifunction DAQ for USB - 16-Bit, up to 400 ks/s, up to 32 Analog Inputs, Isolation Technical Sales United States (866) 531-6285 info@ni.com Print E-mail this Page Open Document as PDF Requirements and Compatibility Ordering Information Detailed Specifications Pinouts/Front Panel Connections

More information

NI PXIe-5601 Specifications

NI PXIe-5601 Specifications NI PXIe-5601 Specifications RF Downconverter This document lists specifications for the NI PXIe-5601 RF downconverter (NI 5601). Use the NI 5601 with the NI PXIe-5622 IF digitizer and the NI PXI-5652 RF

More information

NI SCXI Specifications

NI SCXI Specifications NI SCXI -1127 Specifications 32-Channel Relay Multiplexer/Matrix Input Characteristics This document lists specifications for the NI SCXI-1127 multiplexer/matrix module. All specifications are subject

More information

X Series Data Acquisition: 1.25 MS/s, 32 AI, 48 DIO, 4 AO

X Series Data Acquisition: 1.25 MS/s, 32 AI, 48 DIO, 4 AO DEVICE SPECIFICATIONS NI 6353 X Series Data Acquisition: 1.25 MS/s, 32 AI, 48 DIO, 4 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6353,

More information

NI PXI/PCI-5411/5431 Specifications

NI PXI/PCI-5411/5431 Specifications NI PXI/PCI-5411/5431 Specifications NI PXI/PCI-5411 High-Speed Arbitrary Waveform Generator NI PXI/PCI-5431 Video Waveform Generator Analog Output This document lists the specifications for the NI PXI/PCI-5411

More information

X Series Data Acquisition: 1.25 MS/s, 16 AI, 24 DIO, 2 AO

X Series Data Acquisition: 1.25 MS/s, 16 AI, 24 DIO, 2 AO DEVICE SPECIFICATIONS NI 6351 X Series Data Acquisition: 1.25 MS/s, 16 AI, 24 DIO, 2 AO The following specifications are typical at 25 C, unless otherwise noted. For more information about the NI 6351,

More information

R Series for USB Multifunction RIO with Kintex-7 160T FPGA. ni.com/manuals

R Series for USB Multifunction RIO with Kintex-7 160T FPGA. ni.com/manuals SPECIFICATIONS NI USB-7846R OEM R Series for USB Multifunction RIO with Kintex-7 160T FPGA Français Deutsch 日本語한국어简体中文 ni.com/manuals This document contains the specifications for the National Instruments

More information

NI PXI-2521 Specifications 40-Channel DPST Relay Module

NI PXI-2521 Specifications 40-Channel DPST Relay Module NI PXI-2521 Specifications 40-Channel DPST Relay Module This document lists specifications for the NI PXI-2521 general-purpose relay module. All specifications are subject to change without notice. Visit

More information

NI PXI-2555 Specifications

NI PXI-2555 Specifications NI PXI-2555 Specifications 2.5 GHz Terminated 4 x 1 Multiplexer (SP4T) This document lists specifications for the NI PXI-2555 multiplexer module. All specifications are subject to change without notice.

More information

NI PXI-2520 Specifications 80-Channel SPST Relay Module

NI PXI-2520 Specifications 80-Channel SPST Relay Module NI PXI-2520 Specifications 80-Channel SPST Relay Module This document lists specifications for the NI PXI-2520 general-purpose relay module. All specifications are subject to change without notice. Visit

More information

DEVICE SPECIFICATIONS NI PXIe Ch, 24-bit, 25.6 ks/s Simultaneous AC LVDT Input Module

DEVICE SPECIFICATIONS NI PXIe Ch, 24-bit, 25.6 ks/s Simultaneous AC LVDT Input Module DEVICE SPECIFICATIONS NI PXIe-4340 4 Ch, 24-bit, 25.6 ks/s Simultaneous AC LVDT Input Module This document lists specifications for the NI PXIe-4340 simultaneous AC LVDT input module. All specifications

More information

NI PXI-2557 Specifications

NI PXI-2557 Specifications NI PXI-2557 Specifications 2.5 GHz 75 8 x 1 Multiplexer (SP8T) This document lists specifications for the NI PXI-2557 multiplexer module. All specifications are subject to change without notice. Visit

More information

NI PXI/PXIe-2529 Specifications

NI PXI/PXIe-2529 Specifications NI PXI/PXIe-2529 Specifications 128-Crosspoint Relay Matrix This document lists specifications for the NI PXI/PXIe-2529 (NI 2529) matrix module. All specifications are subject to change without notice.

More information

32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device

32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device SPECIFICATIONS USB-6363 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO USB Multifunction I/O Device These specifications apply to the USB-6363 BNC, USB-6363 Mass Termination, and USB-6363 Spring Terminal.

More information

NI PXI/PCI-6561/6562 Specifications

NI PXI/PCI-6561/6562 Specifications NI PXI/PCI-6561/6562 Specifications 100/200 MHz Digital Waveform Generator/Analyzer Contents This document provides the specifications for the NI PXI/PCI-6561 (NI 6561) and the NI PXI/PCI-6562 (NI 6562),

More information

NI PXI/PXIe-2532 Specifications

NI PXI/PXIe-2532 Specifications NI PXI/PXIe-2532 Specifications 512-Crosspoint, 1-Wire Matrix This document lists specifications for the NI PXI/PXIe-2532 (NI 2532) 512-crosspoint matrix. All specifications are subject to change without

More information

NI PXI-2530 Specifications

NI PXI-2530 Specifications NI PXI-2530 Specifications 128-Channel Reed Relay Multiplexer/Matrix This document lists specifications for the National Instruments PXI-2530 128-channel multiplexer/matrix module. All specifications are

More information

NI PXIe-5630 Specifications

NI PXIe-5630 Specifications NI PXIe-5630 Specifications RF Vector Network Analyzer This document lists specifications for the NI PXIe-5630 RF vector network analyzer (NI 5630). Specifications are warranted under the following conditions:

More information

NI PXI-2797 Specifications 40 GHz 6 1 Terminated 50 Ω Multiplexer

NI PXI-2797 Specifications 40 GHz 6 1 Terminated 50 Ω Multiplexer NI PXI-2797 Specifications 40 GHz 6 1 Terminated 50 Ω Multiplexer This document lists specifications for the NI PXI-2797 terminated multiplexer module. All specifications are subject to change without

More information

Power Amplifier. Input Characteristics. SPECIFICATIONS NI PXIe-4610 Power Amplifier. Signal Range

Power Amplifier. Input Characteristics. SPECIFICATIONS NI PXIe-4610 Power Amplifier. Signal Range SPECIFICATIONS NI PXIe-4610 Power Amplifier This document lists specifications for the NI PXIe-4610 Power Amplifier. These specifications are typical at 25 ºC unless otherwise stated. The operating range

More information

NI PXIe-5663 Specifications

NI PXIe-5663 Specifications NI PXIe-5663 Specifications 6.6 GHz RF Vector Signal Analyzer with Digital Downconversion This document lists specifications for the NI PXIe-5663 RF vector signal analyzer (NI 5663). The NI 5663 comprises

More information

SPECIFICATIONS PXIe Ch (8 ADC), 2 MS/s, bit, Flexible Resolution PXI Analog Input Module

SPECIFICATIONS PXIe Ch (8 ADC), 2 MS/s, bit, Flexible Resolution PXI Analog Input Module SPECIFICATIONS PXIe-4309 32 Ch (8 ADC), 2 MS/s, 18-28 bit, Flexible Resolution PXI Analog Input Module This document lists specifications for the PXIe-4309 data acquisition module. All specifications are

More information

NI PXI/PXIe-2540 Specifications

NI PXI/PXIe-2540 Specifications NI PXI/PXIe-254 Specifications 35 MHz 8 9 5 Ω Matrix This document lists specifications for the NI PXI/PXIe-254 (NI 254) matrix module. All specifications are subject to change without notice. Visit ni.com/manuals

More information

NI PXI/PXIe-2527 Specifications

NI PXI/PXIe-2527 Specifications NI PXI/PXIe-2527 Specifications 32 1 Relay Multiplexer This document lists specifications for the NI PXI/PXIe-2527 (NI 2527) 32 1 multiplexer relay module. All specifications are subject to change without

More information

DEVICE SPECIFICATIONS NI PXIe-4302/ Ch, 24-bit, 5 ks/s or 51.2 ks/s Simultaneous Filtered Data Acquisition Module

DEVICE SPECIFICATIONS NI PXIe-4302/ Ch, 24-bit, 5 ks/s or 51.2 ks/s Simultaneous Filtered Data Acquisition Module DEVICE SPECIFICATIONS NI PXIe-4302/4303 32 Ch, 24-bit, 5 ks/s or 51.2 ks/s Simultaneous Filtered Data Acquisition Module This document lists specifications for the NI PXIe-4302/4303 simultaneous filtered

More information

NI PXI/PXIe-2541 Specifications 300 MHz Ω Matrix

NI PXI/PXIe-2541 Specifications 300 MHz Ω Matrix NI PXI/PXIe-2541 Specifications 3 MHz 8 12 5 Ω Matrix This document lists specifications for the NI PXI/PXIe-2541 (NI 2541) matrix module. All specifications are subject to change without notice. Visit

More information

NI 2865A 0.3 A Matrix Cards for NI SwitchBlock

NI 2865A 0.3 A Matrix Cards for NI SwitchBlock SPECIFICATIONS NI 2865A 0.3 A Matrix Cards for NI SwitchBlock This document lists specifications for the NI 2865A matrix relay cards. All specifications are subject to change without notice. Visit ni.com/manuals

More information

DEVICE SPECIFICATIONS NI PXIe-4304/ Ch, 24-bit, ±42 V, 5 ks/s or 51.2 ks/s Simultaneous Filtered Data Acquisition Module. ni.

DEVICE SPECIFICATIONS NI PXIe-4304/ Ch, 24-bit, ±42 V, 5 ks/s or 51.2 ks/s Simultaneous Filtered Data Acquisition Module. ni. DEVICE SPECIFICATIONS NI PXIe-4304/4305 32 Ch, 24-bit, ±42 V, 5 ks/s or 51.2 ks/s Simultaneous Filtered Data Acquisition Module Français Deutsch ni.com/manuals This document lists specifications for the

More information

R Series for USB Multifunction RIO with Kintex-7 70T FPGA

R Series for USB Multifunction RIO with Kintex-7 70T FPGA SPECIFICATIONS NI USB-7845R OEM R Series for USB Multifunction RIO with Kintex-7 70T FPGA This document contains the specifications for the NI USB-7845R OEM device. Specifications are typical at 25 C unless

More information

R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 8 AI, 8 AO, 48 DIO, 500 ks/s AI, Kintex-7 160T FPGA

R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 8 AI, 8 AO, 48 DIO, 500 ks/s AI, Kintex-7 160T FPGA SPECIFICATIONS NI PXIe-7846R R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 8 AI, 8 AO, 48 DIO, 500 ks/s AI, Kintex-7 160T FPGA This document contains the specifications for the NI PXIe-7846R.

More information

100 MHz Bandwidth, 12-Bit PXI Waveform Generator

100 MHz Bandwidth, 12-Bit PXI Waveform Generator SPECIFICATIONS PXI-5404 100 MHz Bandwidth, 12-Bit PXI Waveform Generator Contents Conditions... 1 CH 0 Outputs... 2 CH 0 SINE Out... 2 CH 0 CLOCK Out...4 PFI 0 I/O...5 REF IN... 6 REF OUT... 7 Start Trigger...

More information

PXI Contents. Definitions SPECIFICATIONS. ±100 V, 2 W Precision PXI Source Measure Unit. These specifications apply to the PXI-4132.

PXI Contents. Definitions SPECIFICATIONS. ±100 V, 2 W Precision PXI Source Measure Unit. These specifications apply to the PXI-4132. SPECIFICATIONS PXI-4132 ±100 V, 2 W Precision PXI Source Measure Unit These specifications apply to the PXI-4132. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 6 AI, 18 AO, 48 DIO, 1 MS/s AIO, 512 MB DRAM, Kintex-7 325T FPGA

R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 6 AI, 18 AO, 48 DIO, 1 MS/s AIO, 512 MB DRAM, Kintex-7 325T FPGA SPECIFICATIONS NI PXIe-7868R R Series Reconfigurable I/O Module (AI, AO, DIO) for PXI Express, 6 AI, 18 AO, 48 DIO, 1 MS/s AIO, 512 MB DRAM, Kintex-7 325T FPGA This document contains the specifications

More information

R Series for USB Multifunction RIO with Kintex-7 70T FPGA. may impair the protection the NI USB-7855R provides.

R Series for USB Multifunction RIO with Kintex-7 70T FPGA. may impair the protection the NI USB-7855R provides. SPECIFICATIONS NI USB-7855R R Series for USB Multifunction RIO with Kintex-7 70T FPGA This document contains the specifications for the NI USB-7855R. Specifications are typical at 25 C unless otherwise

More information

OPERATING INSTRUCTIONS AND SPECIFICATIONS. NI 9207E 16-Channel, ±20 ma/±10 V, 24-Bit Analog Input Module

OPERATING INSTRUCTIONS AND SPECIFICATIONS. NI 9207E 16-Channel, ±20 ma/±10 V, 24-Bit Analog Input Module OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9207E 16-Channel, ±20 ma/±10 V, 24-Bit Analog Input Module This document describes how to use the National Instruments 9207E and includes dimensions, pin assignments,

More information

SCXI MHz Quad 8x1 50 Ω Multiplexer

SCXI MHz Quad 8x1 50 Ω Multiplexer SPECIFICATIONS SCXI -1193 500 MHz Quad 50 Ω Multiplexer This document lists specifications for the SCXI-1193 multiplexer module. All specifications are subject to change without notice. Visit ni.com/manuals

More information

NI PXI/PCI-5122 Specifications

NI PXI/PCI-5122 Specifications NI PXI/PCI-5122 Specifications 14-Bit 100 MS/s Digitizer Contents Unless otherwise noted, the following conditions were used for each specification: All filter settings All impedance selections Sample

More information

1- or 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module

1- or 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module SPECIFICATIONS PXI-8512 1- or 2-Port, High-Speed, Flexible Data Rate PXI CAN Interface Module This document lists specifications for the PXI-8512 1-port and 2-port CAN interface module. Definitions Warranted

More information

PXIe, 24-Channel, ±24 V, 50 ma Precision PXI Source Measure Unit

PXIe, 24-Channel, ±24 V, 50 ma Precision PXI Source Measure Unit SPECIFICATIONS PXIe-4163 PXIe, 24-Channel, ±24 V, 50 ma Precision PXI Source Measure Unit Contents Definitions...1 Conditions... 2 Instrument Capabilities... 2 SMU Specifications... 3 Voltage...3 Current...

More information

NI 5421 Specifications NI PXI/PCI Bit 100 MS/s Arbitrary Waveform Generator

NI 5421 Specifications NI PXI/PCI Bit 100 MS/s Arbitrary Waveform Generator NI 5421 Specifications NI PXI/PCI-5421 16-Bit 100 MS/s Arbitrary Waveform Generator Unless otherwise noted, the following conditions were used for each specification: Contents Analog Filter enabled. Interpolation

More information

PXI Contents SPECIFICATIONS. ±20 V, 40 W PXI Source Measure Unit

PXI Contents SPECIFICATIONS. ±20 V, 40 W PXI Source Measure Unit SPECIFICATIONS PXI-4130 ±20 V, 40 W PXI Source Measure Unit These specifications apply to the PXI-4130 with APS-4100 auxiliary power supply and to the PXI-4130 without auxiliary power supply. Contents

More information

PXI Contents SPECIFICATIONS. 1.3 GHz RF Analog Signal Generator

PXI Contents SPECIFICATIONS. 1.3 GHz RF Analog Signal Generator SPECIFICATIONS PXI-5650 1.3 GHz RF Analog Signal Generator Contents Definitions...2 Conditions... 2 Frequency...2 Frequency Settling Time... 3 Reference Clock...3 Internal Clock...3 Internal Reference

More information

4-Channel, ±6 V, 500 ma Precision PXI Source Measure Unit

4-Channel, ±6 V, 500 ma Precision PXI Source Measure Unit SPECIFICATIONS PXIe-4145 4-Channel, ±6 V, 500 ma Precision PXI Source Measure Unit These specifications apply to the PXIe-4145. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

PXIe Contents SPECIFICATIONS. RF Amplifier

PXIe Contents SPECIFICATIONS. RF Amplifier SPECIFICATIONS PXIe-5698 RF Amplifier Contents Definitions...2 Conditions... 2 Amplitude...3 Minimal Gain... 3 Noise Figure...4 Average Noise Level... 5 Absolute Amplitude Accuracy...7 Spurious Responses...8

More information

PXI Contents SPECIFICATIONS. 6.6 GHz RF Analog Signal Generator

PXI Contents SPECIFICATIONS. 6.6 GHz RF Analog Signal Generator SPECIFICATIONS PXI-5652 6.6 GHz RF Analog Signal Generator Contents Definitions...2 Conditions... 2 Frequency...2 Frequency Settling Time... 3 Reference Clock...3 Internal Clock...3 Internal Reference

More information

Note Using the PXIe-5785 in a manner not described in this document might impair the protection the PXIe-5785 provides.

Note Using the PXIe-5785 in a manner not described in this document might impair the protection the PXIe-5785 provides. SPECIFICATIONS PXIe-5785 PXI FlexRIO IF Transceiver This document lists the specifications for the PXIe-5785. Specifications are subject to change without notice. For the most recent device specifications,

More information

PXIe Contents. Definitions SPECIFICATIONS. 8.5 GHz Vector Network Analyzer

PXIe Contents. Definitions SPECIFICATIONS. 8.5 GHz Vector Network Analyzer SPECIFICATIONS PXIe-5632 8.5 GHz Vector Network Analyzer Contents Definitions...1 Conditions... 2 General Information...2 Source Characteristics...3 Receiver Characteristics...5 Measurement Speed... 6

More information

PXIe Contents SPECIFICATIONS. 3.3 GHz RF Analog Signal Generator

PXIe Contents SPECIFICATIONS. 3.3 GHz RF Analog Signal Generator SPECIFICATIONS PXIe-5651 3.3 GHz RF Analog Signal Generator Contents Definitions...2 Conditions... 2 Frequency...2 Frequency Settling Time... 3 Reference Clock...3 Internal Clock...3 Internal Reference

More information

PXIe Contents SPECIFICATIONS. 250 khz to 20 GHz RF Analog Signal Generator

PXIe Contents SPECIFICATIONS. 250 khz to 20 GHz RF Analog Signal Generator SPECIFICATIONS PXIe-5654 250 khz to 20 GHz RF Analog Signal Generator These specifications apply to the PXIe-5654 RF Analog Signal Generator with up to 10 GHz or 20 GHz frequency and the PXIe-5696 Amplitude

More information

Refer to the NI Switches Help at ni.com/manuals for detailed topology information.

Refer to the NI Switches Help at ni.com/manuals for detailed topology information. DEVICE SPECIFICATIONS NI PXI/PXIe-2593 500 MHz Dual 8 1 50 Ω Multiplexer This document lists specifications for the NI PXI/PXIe-2593 (NI 2593). All specifications are subject to change without notice.

More information

4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit

4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit SPECIFICATIONS PXIe-4141 4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit These specifications apply to the PXIe-4141. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

4-Channel, ±24 V, 150 ma PXI Source Measure Unit

4-Channel, ±24 V, 150 ma PXI Source Measure Unit SPECIFICATIONS PXIe-4142 4-Channel, ±24 V, 150 ma PXI Source Measure Unit These specifications apply to the PXIe-4142. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

1- or 2-Port, Software-Selectable PXI CAN Interface Module

1- or 2-Port, Software-Selectable PXI CAN Interface Module SPECIFICATIONS PXI-8513 1- or 2-Port, Software-Selectable PXI CAN Interface Module This document lists specifications for the PXI-8513 1-port and 2-port CAN interface module. Definitions Warranted specifications

More information

4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit

4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit SPECIFICATIONS PXIe-4141 4-Channel ±10 V, 100 ma, Precision PXI Source Measure Unit These specifications apply to the PXIe-4141. Contents Definitions...1 Conditions... 2 Device Capabilities... 2 SMU Specifications...

More information

SPECIFICATIONS FOR THE NI PXI/PCI-4060

SPECIFICATIONS FOR THE NI PXI/PCI-4060 SPECIFICATIONS FOR THE NI PXI/PCI-4060 This document lists the specifications of the NI PXI/PCI-4060. These specifications are guaranteed between 15 and 35 C unless otherwise specified. DC Voltage (% of

More information

SCC-FV01 Frequency Input Module

SCC-FV01 Frequency Input Module USER GUIDE SCC-FV01 Frequency Input Module Conventions The SCC-FV01 frequency input module is a frequency-to-voltage converter designed to measure signals from frequency-generating sensors and other periodic

More information

PXI Timing and Synchronization Control

PXI Timing and Synchronization Control NI PXI-665x Works with all PXI modules Multichassis PXI synchronization Onboard routing of internal or external clock and trigger signals PXI slot 2 star trigger controller Onboard high-stability references

More information

NI PXI/PCI-5402/5406 Specifications 14/16-Bit, 20/40 MHz Arbitrary Function Generator

NI PXI/PCI-5402/5406 Specifications 14/16-Bit, 20/40 MHz Arbitrary Function Generator NI PXI/PCI-5402/5406 Specifications 14/16-Bit, 20/40 MHz Arbitrary Function Generator This document lists specifications for the NI PXI/PCI-5402/5406 (NI 5402/5406) arbitrary function generator. Unless

More information

NI PXI Contents DEVICE SPECIFICATIONS. RF Attenuator

NI PXI Contents DEVICE SPECIFICATIONS. RF Attenuator DEVICE SPECIFICATIONS NI PXI-5695 RF Attenuator This document lists the specifications of the NI PXI-5695 (NI 5695) RF attenuator. Specifications are warranted by design and under the following conditions

More information

Terminology. Output Characteristics. DEVICE SPECIFICATIONS NI PXIe-4463 DSA Analog Output. ni.com/manuals

Terminology. Output Characteristics. DEVICE SPECIFICATIONS NI PXIe-4463 DSA Analog Output. ni.com/manuals DEVICE SPECIFICATIONS NI PXIe-4463 DSA Analog Output Français Deutsch ni.com/manuals This document lists specifications for the NI PXIe-4463 Dynamic Signal Acquisition (DSA) analog output module. All specifications

More information