Ultrasonic Testing using a unipolar pulse

Size: px
Start display at page:

Download "Ultrasonic Testing using a unipolar pulse"

Transcription

1 Ultrasonic Testing using a unipolar pulse by Y. Udagawa* and T. Shiraiwa** *Imaging Supersonic Laboratories Co.,Ltd Tezukayamanakamachi Nara Japan Abstract Krautkramer Japan Co.,Ltd Sumida 1-chome Higashiosaka Japan Characteristics and advantage of ultrasonic testing using a unipolar pulse, which has plus amplitude only or minus amplitude only, have been studied theoretically and experimentally together with study of ordinary method. Ordinary ultrasonic testing uses a burst waves or a short pulse that has alternative amplitudes (called current method). In this case, intensifying and weakening of wave result from overlapping of converged waves according to their phase differences. However, in the case of a unipolar pulse, only intensifying occurs. This gives following significant effects to ultrasonic testing. 1. In the near-distance field of a transducer, sound pressure of a long sinusoidal transmitted wave oscillates according to the distance from the transducer. One of a short transmitted pulse having alternative amplitudes has peaks at both sides of the near field. On the other hand, in the new method, the sound pressure of a pulse has constant distribution and also the pulse energy, which is sum of the waves emitted from all points of the transducer, becomes large. This gives inspection of a constant and high sensitivity in the near-distance field. 2. In the coarse grain materials such as concrete and firebrick, ultrasonic beam is scattered by grains and it reduces the received intensity and inspection of such material is difficult. At an observing point, many scattered waves, which have phase differences, are received. In the current method, intensifying by interference of scattered waves is limited. In the new method, intensifying of pulse energy is not limited by interference and pulse length is elongated. Then, we can get a pulse of large total intensity. This enables us inspection of coarse grain materials, by using a receiving amplifier of frequency band appropriate to the received elongated pulse. 2. Introduction A transmitter, that can emit a unipolar pulse, has been developed and ultrasonic testing using such a pulse has become possible. Ordinary ultrasonic testing uses a sinusoidal wave pulse of narrow or wide frequency band, of which amplitude oscillates plus and minus alternatively. There are cases where the acoustic field is made from superpose of many waves of different phases in the medium under the ultrasonic testing and interference between those dipolar pulses causes intensifying and weakening of the superposed pulse. Intensifying is limited in the range of phase difference smaller than 1

2 18 degrees. If it is over 18 degrees, interference acts as compensation. When the phase difference has constant distribution, the superposed intensity is an average intensity of the pulse, which is usually zero value. On the other hand, interference between unipolar pulses causes intensifying only. When the phase difference is over the pulse length, the length of superposed pulse is elongated and total energy of it increases. Above-mentioned phenomena give the significant effect on the ultrasonic testing. In the present paper, those effects are investigated by numerical simulation for two cases, near field of the transducer and a pulse in the coarse grain materials. 3. Near field of a plane circular transducer of a unipolar pulse 3.1. Calculation Numerical calculation of acoustic field of a transducer was carried on the following equation, f ( t r / v) P = ds r S (1) Where P is acoustic pressure at an observing point, f is acoustic pressure of the transmitted pulse, t is time, r is distance from the source to the observing point, v is sound velocity and S means transducer surface. A transducer is plane and circular and the diameter is 2. Linear dimension is normalized by wavelength and time is normalized by period. These are shown in Fig.1. Calculation was done on the following three pulses. Pulse 1. A unipolar pulse which is one quota period of sinusoidal wave Pulse 2. An asymmetric sinusoidal pulse of one and half of waves as a represent of short pulse Pulse 3. A sinusoidal pulse of four waves as a represent of burst wave These pulses are shown in Fig Result and discussion Results of calculation are shown in Fig.3. X and Z is Z Transducer X,Z Fig.1. Calculation of acoustic field of a circular transducer Fig.2 Shape of transmitted pulse X Pulse 1 Pulse 2 Pulse 3

3 shown in Fig.1. Z of 1 is so called transition point from near field to far field. In the figure, the maximum amplitude of pulse is plotted. In (b) and (c), the maximum amplitudes of plus and minus amplitude of pulse are shown. As shown in Fig.3 (a), near field of Pulse 1, a unipolar pulse, has constant distribution near the transducer surface and its width decreases as Z. Near field of Pulse 2, asymmetric sinusoidal pulse of waves, is shown in Fig.3 (b). The plus amplitude has constant distribution but minus amplitude has a peak at the side of distribution, of which reason will be shown in later. Fig. 3 (c) shows near field of Pulse 3, sinusoidal pulse of 4 waves. The amplitude fluctuates as well known. Calculation of eq.(1) also gives the pulse shape and they are shown in Fig.4 for the representative points. In order to understand the calculation result especially for the oscillating pulse, we consider the results on the central axis of transducer. On the central axis of the transducer, Z axis in Fig.1, eq.(1) can be expressed as a following analytical form, because of compensation of r factors. r = sin ( ) = 2 ( ) = 2 t r θ P f t t dφdx π f t t dr πv r r L (a) Pulse 1, unipolar pulse t T f ( t t) d( t) Z=25 (+) (2). Where L is length of pulse in distance and T is length of pulse in time. Integral limit in Z= (-) 5 (+) 5 (-) 75 (+) 75 (-) 1 (+) 1 (-) (b) Pulse 2, asymmetric sinusoidal pulse of waves. (c) Pulse 3, sinusoidal pulse of 4 waves. X X X Z=25 (+) 25 (-) 5 (+) 5 (-) 75 (+) 75 (-) 1 (+) 1 (-) Fig.3. Near field of a circular plane transducer for Pulse 1, 2 and 3. 3

4 X=,Z=25 X=,Z=5 X=,Z=1 X=3,Z=25 X=3,Z=5 (a) Pulse 1, unipolar pulse X=,Z=25 X=,Z=5 X=,Z=1 X=3,Z=25 X=5,Z=25 (b) Pulse 2, asymmetric sinusoidal pulse of waves X=,Z=25 X=,Z=5 X=,Z=1 X=3,Z=25 X=5,Z=25 (c) Pulse 3, sinusoidal pulse of 4 waves Fig.4. Received pulse shape at point (X,Z) for pulse 1,2 and 3 Abscissa is time in period and ordinate is amplitude of same magnitude as Fig.2. Start of each pulse is shifted by.25. eq.(2) is further limited by the source position. The lower limit of t is the shortest travelling time and the upper one is the longest travelling time. If there is no limitation for them and eq.(2) is integrated over domain of T, it is zero for ordinary oscillating pulse, dipolar pulse. It has practical value only for integral over time domain smaller 4

5 than T. That is, eq.(2) is not zero for the first arrival pulse group and the last arrival one. Eq.(2) can be converted for those time domain as following respectively, except constant terms, τ T f ( τ ) dτ (2a), and f ( τ ) dτ f ( τ) dτ (2b). Where starts at the arrival time of first pulse in (2a) and at the arrival time of end pulse in (2b) and the first term of (2b) is usually zero.. For a unipolar pulse, eq.(2) is not zero because of no cancellation of interference. As shown in a left figure of Fig.4 (a) for a unipolar pulse, the pulse succeeds the first integrated pulse continuously, and the total pulse length is elongated in the range of arrival time delay. The pulse length decreases with Z and it becomes as same as the transmitted pulse at Z=1 which is the transition point from the near field to the far field. The left figure of Fig.4 (b) shows received pulse shape of Pulse 2, asymmetric sinusoidal pulse of waves, on the central axis. It is clearly shown in the figure for Z=25, that the pulse is composed by two peaks, the arrival peak and the end peak which are given by eq.(2a) and (2b). The end peak looks like as if it starts from the transducer edge. This is a same phenomenon as the edge scattering. Interference of both pulses gives distributions in Fig.3. The left figure of Fig. 4 (c) can be interpreted in the same way. At positions off the central axis, the pulse shape becomes more complex because of r factor. But principle of formation of pulse shape is same Section Conclusion A received pulse of a unipolar pulse in the near field has shape of elongated unipolar pulse. The peak amplitude is given by integral of emitted pulse and the width is given by the delay of pulse emitted from the transducer edge. The peak amplitude distributes uniformly and it is useful for inspection of constant sensitivity. τ 4. Unipolar pulse in the coarse grain material Reflection of ultrasonic pulse at grain boundaries in the coarse grain materials such as concrete attenuates the transmitting pulse. This is a main reason of difficulty of ultrasonic testing of such materials. Reflected pulse also travels in the material. Acoustic field in the material is sum of the directly transmitted pulse and many reflected pulses. However those pulses have delay of arrival time because of different travelling distances. The superposed pulse of them is given as result of their interference. A unipolar pulse intensifies each other by interference. The delay of arrival pulse elongates the superposed pulse. On the other hand, dipolar pulses intensify and compensate each other by interference. 5

6 4.1 Numerical simulation Calculation was done on the following assumption. Attenuation is caused by the grain boundary reflection. Reflection direction is isotropic and the reflection points distribute uniformly. Only the primary reflection is included in the calculation. The secondary and the tertiary reflections and so on are neglected. Linear dimension is normalized by wavelength. The sound pressure is calculated in the far field. Integration is given by the following equation. S ds V µ f ( t)exp( µ ( R1 + R2))/(4πR1R2) dv (3) Where is attenuation coefficient and V is volume in which reflection occurs. Distance R1 and R2 are shown in Fig.5. If the reflection induces phase change, sign of eq.(3) is inverted Result and discussion Transducer Fig.5 shows pulse shapes of a received pulse for a unipolar pulse of Fig.2 observed at Z=1. The transducer is a circular one of radius 1. Ordinate is the same magnitude as Fig.2. In R1 Fig.5 a directly transmitted pulse and a superposed pulse of scattered pulses are shown. Legth of the superposed reflected Z pulse is very long compared to the emitted pulse. In Fig.6, shape of received pulse at Z=1 for a sinusoidal R2 pulse of waves, Pulse 2 in Fig.2, emitted from the same Fig.5 Integration of transducer is shown. The length of superposed pulse of reflected pulse reflected pulse is same as the length of transmitted pulse. The same result is obtained for Pulse 3. In comparison of Fig.5 and Fig. 6, The most significant difference is length of pulse. Reflected unipolar pulses compose a long pulse, but reflected dipolar pulses can not form a long pulse because of interference. Pulse energy becomes large as pulse length. Then we can detect the intense unipolar pulse by using an amplifier, which has an appropriate low frequency band. Above-mentioned result is right qualitatively although it is not correct quantitatively because of rough assumption. If there is phase change at reflection and the secondary reflections occur, results become more complex Section Conclusion A unipolar pulse has low frequency component as well known in function and it is sometimes thought that it can penetrate the coarse grain materials. However the present calculation shows that the superposition of scattered pulses having various delay times gives long pulse length and large energy to the transparent pulse. This result suggests that the transmission of a unipolar pulse and receiving it by an amplifier of low frequency band is effective for ultrasonic testing of coarse grain materials. 6

7 1.2E-1 2.5E-4 E-1 8.E-2 6.E-2 4.E-2 E-2 E-4 E-4 E-4 5.E-5 E+ E Reflected Direct Reflected Direct (a) 3/wavelength (b).1/wavelength Fig.6 Pulse shape of a directly transmitted pulse and a superposed pulse of reflected pulses by grain boundaries for a unipolar pulse emitted from a circular transducer of radius 1 at Z=1. Fig.7 Pulse shape of a directly transmitted pulse and a superposed pulse of reflected pulses by grain boundaries for a sinusoidal pulse of waves emitted E-4 E-4 5.E-5 E+ -5.E Reflected Direct from a circular transducer of radius 1 at Z=1. is.1/wavelength. -E-4 -E-4 5. Experimental Result Figure 8 shows examples of experimental results using a uniopolar pulse. Fig.8(a) is a transmitted pulse received in front of the transducer which is 2MHz and 2mm diameter. Fig.8 (b) and (c) are pulses passed through a concrete slab of 25mm thickness and a cork plate of 25mm thickness respectively. Both materials are very difficult to inspect by ultrasonic testing because a usual ultrasonic pulse cannot pass through them. In the present case, using a unipolar pulse, pulses transmitted through them can been obtained. However, the spatial conditions inside of such materials are very different, point to point. Then, in the present experiment, data obtained for many different points were summed. As shown in Fig.8, pulse length of transmitted pulse is about 2 micro seconds and received pulse lengths after passing through concrete and cork are a few tens of micro seconds. This means that many delayed pulses through materials 7

8 superpose and make a long pulse. 6. Conclusion Characteristics of ultrasonic testing using a unipolar pulse have been studied by numerical simulation and experiment, and following results have been obtained. (1) Unipolar pulses which have phase delays make a long superposed pulse, in contrast to the dipolar pulse in which superposition effect is limited by interference. To detect the superposed pulse it is better to use an amplifier of frequency band matched it. (2) In the near field of transducer, a unipolar pulse gives a constant field. (3) A unipolar pulse can pass through medium, which has large grains, such as concrete and cork. It enables us to inspect such materials by the ultrasonic testing Time in microsec (a) Transmitted pulse 5 1 Time in microsec (b) Received pulse after passing through concrete of 25mm t Time in microsec (c) Received pulse after passing through cork of 25mm t. Fig.8 Pulse shapes of (a) transmitted pulse, and pulse after passing through (b) concrete and (c) cork. 8

Understanding How Frequency, Beam Patterns of Transducers, and Reflection Characteristics of Targets Affect the Performance of Ultrasonic Sensors

Understanding How Frequency, Beam Patterns of Transducers, and Reflection Characteristics of Targets Affect the Performance of Ultrasonic Sensors Characteristics of Targets Affect the Performance of Ultrasonic Sensors By Donald P. Massa, President and CTO of Massa Products Corporation Overview of How an Ultrasonic Sensor Functions Ultrasonic sensors

More information

Ultrasound Beamforming and Image Formation. Jeremy J. Dahl

Ultrasound Beamforming and Image Formation. Jeremy J. Dahl Ultrasound Beamforming and Image Formation Jeremy J. Dahl Overview Ultrasound Concepts Beamforming Image Formation Absorption and TGC Advanced Beamforming Techniques Synthetic Receive Aperture Parallel

More information

Ultrasound Physics. History: Ultrasound 2/13/2019. Ultrasound

Ultrasound Physics. History: Ultrasound 2/13/2019. Ultrasound Ultrasound Physics History: Ultrasound Ultrasound 1942: Dr. Karl Theodore Dussik transmission ultrasound investigation of the brain 1949-51: Holmes and Howry subject submerged in water tank to achieve

More information

Spectral Distance Amplitude Control for Ultrasonic Inspection of Composite Components

Spectral Distance Amplitude Control for Ultrasonic Inspection of Composite Components ECNDT 26 - Mo.2.6.4 Spectral Distance Amplitude Control for Ultrasonic Inspection of Composite Components Uwe PFEIFFER, Wolfgang HILLGER, DLR German Aerospace Center, Braunschweig, Germany Abstract. Ultrasonic

More information

9. Microwaves. 9.1 Introduction. Safety consideration

9. Microwaves. 9.1 Introduction. Safety consideration MW 9. Microwaves 9.1 Introduction Electromagnetic waves with wavelengths of the order of 1 mm to 1 m, or equivalently, with frequencies from 0.3 GHz to 0.3 THz, are commonly known as microwaves, sometimes

More information

Reference wavelets used for deconvolution of ultrasonic time-of-flight diffraction (ToFD) signals

Reference wavelets used for deconvolution of ultrasonic time-of-flight diffraction (ToFD) signals 17th World Conference on Nondestructive Testing, 25-28 Oct 2008, Shanghai, China Reference wavelets used for deconvolution of ultrasonic time-of-flight diffraction (ToFD) signals Farhang HONARVAR 1, Amin

More information

Piezoelectric transducer excitation for guided waves propagation on pipeline with flexural wave modes

Piezoelectric transducer excitation for guided waves propagation on pipeline with flexural wave modes 9 th European Workshop on Structural Health Monitoring July 10-13, 2018, Manchester, United Kingdom Piezoelectric transducer excitation for guided waves propagation on pipeline with flexural wave modes

More information

Fig. 1

Fig. 1 PhysicsAndMathsTutor.com 1 1. Fig. 1 shows data for the intensity of a parallel beam of X-rays after penetration through varying thicknesses of a material. intensity / MW m 2 thickness / mm 0.91 0.40 0.69

More information

ABC Math Student Copy

ABC Math Student Copy Page 1 of 17 Physics Week 9(Sem. 2) Name Chapter Summary Waves and Sound Cont d 2 Principle of Linear Superposition Sound is a pressure wave. Often two or more sound waves are present at the same place

More information

ULTRASONIC GUIDED WAVE ANNULAR ARRAY TRANSDUCERS FOR STRUCTURAL HEALTH MONITORING

ULTRASONIC GUIDED WAVE ANNULAR ARRAY TRANSDUCERS FOR STRUCTURAL HEALTH MONITORING ULTRASONIC GUIDED WAVE ANNULAR ARRAY TRANSDUCERS FOR STRUCTURAL HEALTH MONITORING H. Gao, M. J. Guers, J.L. Rose, G. (Xiaoliang) Zhao 2, and C. Kwan 2 Department of Engineering Science and Mechanics, The

More information

ACCURACY IMPROVEMENT ON NON-INVASIVE ULTRASONIC-DOPPLER FLOW MEASUREMENT BY UTILZING SHEAR WAVES IN METAL PIPE

ACCURACY IMPROVEMENT ON NON-INVASIVE ULTRASONIC-DOPPLER FLOW MEASUREMENT BY UTILZING SHEAR WAVES IN METAL PIPE 4th International Symposium on Ultrasonic Doppler Method for Fluid Mechanics and Fluid Engineering Sapporo, 6.-8. September, 24 ACCURACY IMPROVEMENT ON NON-INVASIVE ULTRASONIC-DOPPLER FLOW MEASUREMENT

More information

A NEW APPROACH FOR THE ANALYSIS OF IMPACT-ECHO DATA

A NEW APPROACH FOR THE ANALYSIS OF IMPACT-ECHO DATA A NEW APPROACH FOR THE ANALYSIS OF IMPACT-ECHO DATA John S. Popovics and Joseph L. Rose Department of Engineering Science and Mechanics The Pennsylvania State University University Park, PA 16802 INTRODUCTION

More information

A progressive wave of frequency 150 Hz travels along a stretched string at a speed of 30 m s 1.

A progressive wave of frequency 150 Hz travels along a stretched string at a speed of 30 m s 1. 1. progressive wave of frequency 150 Hz travels along a stretched string at a speed of 30 m s 1. What is the phase difference between two points that are 50 mm apart on the string? zero 90 180 360 2 Which

More information

Imaging Systems Laboratory II. Laboratory 8: The Michelson Interferometer / Diffraction April 30 & May 02, 2002

Imaging Systems Laboratory II. Laboratory 8: The Michelson Interferometer / Diffraction April 30 & May 02, 2002 1051-232 Imaging Systems Laboratory II Laboratory 8: The Michelson Interferometer / Diffraction April 30 & May 02, 2002 Abstract. In the last lab, you saw that coherent light from two different locations

More information

ENHANCEMENT OF SYNTHETIC APERTURE FOCUSING TECHNIQUE (SAFT) BY ADVANCED SIGNAL PROCESSING

ENHANCEMENT OF SYNTHETIC APERTURE FOCUSING TECHNIQUE (SAFT) BY ADVANCED SIGNAL PROCESSING ENHANCEMENT OF SYNTHETIC APERTURE FOCUSING TECHNIQUE (SAFT) BY ADVANCED SIGNAL PROCESSING M. Jastrzebski, T. Dusatko, J. Fortin, F. Farzbod, A.N. Sinclair; University of Toronto, Toronto, Canada; M.D.C.

More information

ULTRASONIC DEFECT DETECTION IN BILLET USING TIME- OF-FLIGHT OF BOTTOM ECHO

ULTRASONIC DEFECT DETECTION IN BILLET USING TIME- OF-FLIGHT OF BOTTOM ECHO ULTRASONIC DEFECT DETECTION IN BILLET USING TIME- OF-FLIGHT OF BOTTOM ECHO Ryusuke Miyamoto Graduate School of Systems and Information Engineering, University of Tsukuba, Tsukuba, Ibaraki 305-8573 Japan

More information

The electric field for the wave sketched in Fig. 3-1 can be written as

The electric field for the wave sketched in Fig. 3-1 can be written as ELECTROMAGNETIC WAVES Light consists of an electric field and a magnetic field that oscillate at very high rates, of the order of 10 14 Hz. These fields travel in wavelike fashion at very high speeds.

More information

Department of Electrical Engineering and Computer Science

Department of Electrical Engineering and Computer Science MASSACHUSETTS INSTITUTE of TECHNOLOGY Department of Electrical Engineering and Computer Science 6.161/6637 Practice Quiz 2 Issued X:XXpm 4/XX/2004 Spring Term, 2004 Due X:XX+1:30pm 4/XX/2004 Please utilize

More information

Lab 12 Microwave Optics.

Lab 12 Microwave Optics. b Lab 12 Microwave Optics. CAUTION: The output power of the microwave transmitter is well below standard safety levels. Nevertheless, do not look directly into the microwave horn at close range when the

More information

Chapter 17 Waves in Two and Three Dimensions

Chapter 17 Waves in Two and Three Dimensions Chapter 17 Waves in Two and Three Dimensions Slide 17-1 Chapter 17: Waves in Two and Three Dimensions Concepts Slide 17-2 Section 17.1: Wavefronts The figure shows cutaway views of a periodic surface wave

More information

On Determination of Focal Laws for Linear Phased Array Probes as to the Active and Passive Element Size

On Determination of Focal Laws for Linear Phased Array Probes as to the Active and Passive Element Size 19 th World Conference on Non-Destructive Testing 2016 On Determination of Focal Laws for Linear Phased Array Probes as to the Active and Passive Element Size Andreas GOMMLICH 1, Frank SCHUBERT 2 1 Institute

More information

Ultrasonic Transmission Characteristics of Continuous Casting Slab for Medium Carbon Steel

Ultrasonic Transmission Characteristics of Continuous Casting Slab for Medium Carbon Steel Key Engineering Materials Online: 25-11-15 ISSN: 1662-9795, Vols. 297-3, pp 221-226 doi:1.428/www.scientific.net/kem.297-3.221 25 Trans Tech Publications, Switzerland Ultrasonic Transmission Characteristics

More information

RADIATION OF SURFACE WAVES INTO CONCRETE BY MEANS OF A WEDGE TRANSDUCER: DESIGN AND OPTIMIZATION

RADIATION OF SURFACE WAVES INTO CONCRETE BY MEANS OF A WEDGE TRANSDUCER: DESIGN AND OPTIMIZATION RADIATION OF SURFACE WAVES INTO CONCRETE BY MEANS OF A WEDGE TRANSDUCER: DESIGN AND OPTIMIZATION M. Goueygou and B. Piwakowski Electronics & Acoustics Group Institute of Electronics, Microelectronics and

More information

Chapter Ray and Wave Optics

Chapter Ray and Wave Optics 109 Chapter Ray and Wave Optics 1. An astronomical telescope has a large aperture to [2002] reduce spherical aberration have high resolution increase span of observation have low dispersion. 2. If two

More information

ECE 185 ELECTRO-OPTIC MODULATION OF LIGHT

ECE 185 ELECTRO-OPTIC MODULATION OF LIGHT ECE 185 ELECTRO-OPTIC MODULATION OF LIGHT I. Objective: To study the Pockels electro-optic (E-O) effect, and the property of light propagation in anisotropic medium, especially polarization-rotation effects.

More information

Sonic Distance Sensors

Sonic Distance Sensors Sonic Distance Sensors Introduction - Sound is transmitted through the propagation of pressure in the air. - The speed of sound in the air is normally 331m/sec at 0 o C. - Two of the important characteristics

More information

NDI Techniques Supporting Steel Pipe Products

NDI Techniques Supporting Steel Pipe Products JFE TECHNICAL REPORT No. 7 (Jan. 26) IIZUKA Yukinori *1 NAGAMUNE Akio *2 MASAMURA Katsumi *3 Abstract: This paper describes JFE original ultrasonic testing (UT) technologies in Non-destructive inspection

More information

Standard Guide for Evaluating Characteristics of Ultrasonic Search Units 1

Standard Guide for Evaluating Characteristics of Ultrasonic Search Units 1 Designation: E 1065 99 An American National Standard Standard Guide for Evaluating Characteristics of Ultrasonic Search Units 1 This standard is issued under the fixed designation E 1065; the number immediately

More information

Method of Determining Effect of Heat on Mortar by Using Aerial Ultrasonic Waves with Finite Amplitude

Method of Determining Effect of Heat on Mortar by Using Aerial Ultrasonic Waves with Finite Amplitude Proceedings of 20 th International Congress on Acoustics, ICA 2010 23-27 August 2010, Sydney, Australia Method of Determining Effect of Heat on Mortar by Using Aerial Ultrasonic Waves with Finite Amplitude

More information

Compound quantitative ultrasonic tomography of long bones using wavelets analysis

Compound quantitative ultrasonic tomography of long bones using wavelets analysis Compound quantitative ultrasonic tomography of long bones using wavelets analysis Philippe Lasaygues To cite this version: Philippe Lasaygues. Compound quantitative ultrasonic tomography of long bones

More information

Experiment 19. Microwave Optics 1

Experiment 19. Microwave Optics 1 Experiment 19 Microwave Optics 1 1. Introduction Optical phenomena may be studied at microwave frequencies. Using a three centimeter microwave wavelength transforms the scale of the experiment. Microns

More information

Proceedings of Meetings on Acoustics

Proceedings of Meetings on Acoustics Proceedings of Meetings on Acoustics Volume 19, 2013 http://acousticalsociety.org/ ICA 2013 Montreal Montreal, Canada 2-7 June 2013 Physical Acoustics Session 2pPA: Material Characterization 2pPA9. Experimental

More information

NEW LASER ULTRASONIC INTERFEROMETER FOR INDUSTRIAL APPLICATIONS B.Pouet and S.Breugnot Bossa Nova Technologies; Venice, CA, USA

NEW LASER ULTRASONIC INTERFEROMETER FOR INDUSTRIAL APPLICATIONS B.Pouet and S.Breugnot Bossa Nova Technologies; Venice, CA, USA NEW LASER ULTRASONIC INTERFEROMETER FOR INDUSTRIAL APPLICATIONS B.Pouet and S.Breugnot Bossa Nova Technologies; Venice, CA, USA Abstract: A novel interferometric scheme for detection of ultrasound is presented.

More information

EWGAE 2010 Vienna, 8th to 10th September

EWGAE 2010 Vienna, 8th to 10th September EWGAE 2010 Vienna, 8th to 10th September Frequencies and Amplitudes of AE Signals in a Plate as a Function of Source Rise Time M. A. HAMSTAD University of Denver, Department of Mechanical and Materials

More information

Optimization of Ultrasound Broadband Transducers for Complex Testing Problems by Means of Transient and Time Harmonic Sound Fields

Optimization of Ultrasound Broadband Transducers for Complex Testing Problems by Means of Transient and Time Harmonic Sound Fields ECNDT - Poster 1 Optimization of Ultrasound Broadband Transducers for Complex Testing Problems by Means of Transient and Time Harmonic Sound Fields Elfgard Kühnicke, Institute for Solid-State Electronics,

More information

Analytical analysis of modulated signal in apertureless scanning near-field optical microscopy C. H. Chuang and Y. L. Lo *

Analytical analysis of modulated signal in apertureless scanning near-field optical microscopy C. H. Chuang and Y. L. Lo * Research Express@NCKU Volume 5 Issue 10 - October 3, 2008 [ http://research.ncku.edu.tw/re/articles/e/20081003/2.html ] Analytical analysis of modulated signal in apertureless scanning near-field optical

More information

Ultrasonic Air-Coupled Non-Destructive Testing of Aerospace Components

Ultrasonic Air-Coupled Non-Destructive Testing of Aerospace Components ECNDT 2006 - We.1.1.5 Ultrasonic Air-Coupled Non-Destructive Testing of Aerospace Components Rymantas KAZYS, Andrius DEMCENKO, Liudas MAZEIKA, Reimondas SLITERIS, Egidijus ZUKAUSKAS, Ultrasound Institute

More information

REFLECTION AND TRANSMISSION OF LAMB WAVES AT DISCONTINUITY IN PLATE Z. Liu NDT Systems & Services AG, Stutensee, Germany

REFLECTION AND TRANSMISSION OF LAMB WAVES AT DISCONTINUITY IN PLATE Z. Liu NDT Systems & Services AG, Stutensee, Germany REFLECTION AND TRANSMISSION OF LAMB WAVES AT DISCONTINUITY IN PLATE Z. Liu NDT Systems & Services AG, Stutensee, Germany Abstract: Lamb waves can be used for testing thin plate and pipe because they provide

More information

Rayleigh Wave Interaction and Mode Conversion in a Delamination

Rayleigh Wave Interaction and Mode Conversion in a Delamination Rayleigh Wave Interaction and Mode Conversion in a Delamination Sunil Kishore Chakrapani a, Vinay Dayal, a and Jamie Dunt b a Department of Aerospace Engineering & Center for NDE, Iowa State University,

More information

CRACK SIZING USING A NEURAL NETWORK CLASSIFIER TRAINED WITH DATA OBTAINED FROM FINI1E ELEMENT MODELS

CRACK SIZING USING A NEURAL NETWORK CLASSIFIER TRAINED WITH DATA OBTAINED FROM FINI1E ELEMENT MODELS CRACK SIZING USING A NEURAL NETWORK CLASSIFIER TRAINED WITH DATA OBTAINED FROM FINI1E ELEMENT MODELS Kornelija Zgonc, Jan D. Achenbach and Yung-Chung Lee Center for Quality Engineering and Failure Prevention

More information

Identification of periodic structure target using broadband polarimetry in terahertz radiation

Identification of periodic structure target using broadband polarimetry in terahertz radiation Identification of periodic structure target using broadband polarimetry in terahertz radiation Yuki Kamagata, Hiroaki Nakabayashi a), Koji Suizu, and Keizo Cho Chiba Institute of Technology, Tsudanuma,

More information

NONDESTRUCTIVE EVALUATION OF CLOSED CRACKS USING AN ULTRASONIC TRANSIT TIMING METHOD J. Takatsubo 1, H. Tsuda 1, B. Wang 1

NONDESTRUCTIVE EVALUATION OF CLOSED CRACKS USING AN ULTRASONIC TRANSIT TIMING METHOD J. Takatsubo 1, H. Tsuda 1, B. Wang 1 NONDESTRUCTIVE EVALUATION OF CLOSED CRACKS USING AN ULTRASONIC TRANSIT TIMING METHOD J. Takatsubo 1, H. Tsuda 1, B. Wang 1 1 National Institute of Advanced Industrial Science and Technology, Tsukuba, Japan

More information

Countermeasure for Reducing Micro-pressure Wave Emitted from Railway Tunnel by Installing Hood at the Exit of Tunnel

Countermeasure for Reducing Micro-pressure Wave Emitted from Railway Tunnel by Installing Hood at the Exit of Tunnel PAPER Countermeasure for Reducing Micro-pressure Wave Emitted from Railway Tunnel by Installing Hood at the Exit of Tunnel Sanetoshi SAITO Senior Researcher, Laboratory Head, Tokuzo MIYACHI, Dr. Eng. Assistant

More information

7. Consider the following common offset gather collected with GPR.

7. Consider the following common offset gather collected with GPR. Questions: GPR 1. Which of the following statements is incorrect when considering skin depth in GPR a. Skin depth is the distance at which the signal amplitude has decreased by a factor of 1/e b. Skin

More information

ωκε ωκε 5.11 Ground Penetrating Radar (GPR)

ωκε ωκε 5.11 Ground Penetrating Radar (GPR) 5. Ground Penetrating Radar (GPR) The plane wave solutions we have studied so far have been valid for frequencies and conductivities such that the conduction currents dominate the displacement currents

More information

Keywords: Ultrasonic Testing (UT), Air-coupled, Contact-free, Bond, Weld, Composites

Keywords: Ultrasonic Testing (UT), Air-coupled, Contact-free, Bond, Weld, Composites Single-Sided Contact-Free Ultrasonic Testing A New Air-Coupled Inspection Technology for Weld and Bond Testing M. Kiel, R. Steinhausen, A. Bodi 1, and M. Lucas 1 Research Center for Ultrasonics - Forschungszentrum

More information

Detection of Protective Coating Disbonds in Pipe Using Circumferential Guided Waves

Detection of Protective Coating Disbonds in Pipe Using Circumferential Guided Waves 17th World Conference on Nondestructive Testing, 25-28 Oct 2008, Shanghai, China Detection of Protective Coating Disbonds in Pipe Using Circumferential Guided Waves Jason K. Van Velsor Pennsylvania State

More information

Lab 1: Pulse Propagation and Dispersion

Lab 1: Pulse Propagation and Dispersion ab 1: Pulse Propagation and Dispersion NAME NAME NAME Introduction: In this experiment you will observe reflection and transmission of incident pulses as they propagate down a coaxial transmission line

More information

MATERIALS CHARACTERIZATION USING LASER ULTRASONIC GUIDED WAVES

MATERIALS CHARACTERIZATION USING LASER ULTRASONIC GUIDED WAVES MATERIALS CHARACTERIZATION USING LASER ULTRASONIC GUIDED WAVES NDCM XII VA Tech June 19 to 24, 2011 B. Boro Djordjevic Materials and Sensors Technologies, Inc. Maryland, USA 410 766 5002, Fax. 410766 5009,

More information

First and second order systems. Part 1: First order systems: RC low pass filter and Thermopile. Goals: Department of Physics

First and second order systems. Part 1: First order systems: RC low pass filter and Thermopile. Goals: Department of Physics slide 1 Part 1: First order systems: RC low pass filter and Thermopile Goals: Understand the behavior and how to characterize first order measurement systems Learn how to operate: function generator, oscilloscope,

More information

ULTRASONIC GUIDED WAVES FOR AGING WIRE INSULATION ASSESSMENT

ULTRASONIC GUIDED WAVES FOR AGING WIRE INSULATION ASSESSMENT ULTRASONIC GUIDED WAVES FOR AGING WIRE INSULATION ASSESSMENT Robert F. Anastasi 1 and Eric I. Madaras 2 1 U.S. Army Research Laboratory, Vehicle Technology Directorate, AMSRL-VT-S, Nondestructive Evaluation

More information

Proximity Sensors Ultrasonic Precision Proximity Sensors

Proximity Sensors Ultrasonic Precision Proximity Sensors Ultrasonic Precision Proximity Sensors 900 Series ultrasonic position sensors solve the toughest sensing problems. Ultrasonic sensors detect targets made of virtually any material, regardless of color.

More information

Linear arrays used in ultrasonic evaluation

Linear arrays used in ultrasonic evaluation Annals of the University of Craiova, Mathematics and Computer Science Series Volume 38(1), 2011, Pages 54 61 ISSN: 1223-6934 Linear arrays used in ultrasonic evaluation Laura-Angelica Onose and Luminita

More information

Experimental Competition

Experimental Competition 37 th International Physics Olympiad Singapore 8 17 July 2006 Experimental Competition Wed 12 July 2006 Experimental Competition Page 2 List of apparatus and materials Label Component Quantity Label Component

More information

Advanced Ultrasonic Imaging for Automotive Spot Weld Quality Testing

Advanced Ultrasonic Imaging for Automotive Spot Weld Quality Testing 5th Pan American Conference for NDT 2-6 October 2011, Cancun, Mexico Advanced Ultrasonic Imaging for Automotive Spot Weld Quality Testing Alexey A. DENISOV 1, Roman Gr. MAEV 1, Johann ERLEWEIN 2, Holger

More information

IMAGING OF DEFECTS IN CONCRETE COMPONENTS WITH NON-CONTACT ULTRASONIC TESTING W. Hillger, DLR and Ing. Büro Dr. Hillger, Braunschweig, Germany

IMAGING OF DEFECTS IN CONCRETE COMPONENTS WITH NON-CONTACT ULTRASONIC TESTING W. Hillger, DLR and Ing. Büro Dr. Hillger, Braunschweig, Germany IMAGING OF DEFECTS IN CONCRETE COMPONENTS WITH NON-CONTACT ULTRASONIC TESTING W. Hillger, DLR and Ing. Büro Dr. Hillger, Braunschweig, Germany Abstract: The building industries require NDT- methods for

More information

Analysis of Propagation Paths of Partial Discharge Acoustic Emission Signals

Analysis of Propagation Paths of Partial Discharge Acoustic Emission Signals Analysis of Propagation Paths of Partial Discharge Acoustic Emission Signals Prathamesh Dhole, Tanmoy Sinha, Sumeet Nayak, Prasanta Kundu, N.K.Kishore Abstract Transformers are one of the most important

More information

The spatial structure of an acoustic wave propagating through a layer with high sound speed gradient

The spatial structure of an acoustic wave propagating through a layer with high sound speed gradient The spatial structure of an acoustic wave propagating through a layer with high sound speed gradient Alex ZINOVIEV 1 ; David W. BARTEL 2 1,2 Defence Science and Technology Organisation, Australia ABSTRACT

More information

A Numerical study on proper mode and frequency selection for riveted lap joints inspection using Lamb waves.

A Numerical study on proper mode and frequency selection for riveted lap joints inspection using Lamb waves. More Info at Open Access Database www.ndt.net/?id=18676 A Numerical study on proper mode and frequency selection for riveted lap joints inspection using Lamb waves. Mohammad. (. SOORGEE Nondestructive

More information

Ultrasonic Guided Wave Testing of Cylindrical Bars

Ultrasonic Guided Wave Testing of Cylindrical Bars 18th World Conference on Nondestructive Testing, 16-2 April 212, Durban, South Africa Ultrasonic Guided Wave Testing of Cylindrical Bars Masanari Shoji, Takashi Sawada NTT Energy and Environment Systems

More information

DATA AQUISITION AND PROCESSING

DATA AQUISITION AND PROCESSING Chapter 3 DATA AQUISITION AND PROCESSING As discussed in the previous Chapter, first an isothermal pressure experiment was run, followed by an isobar temperature program. The pressure was built up in steps

More information

Spring 2004 M2.1. Lab M2. Ultrasound: Interference, Wavelength, and Velocity

Spring 2004 M2.1. Lab M2. Ultrasound: Interference, Wavelength, and Velocity Spring 2004 M2.1 Lab M2. Ultrasound: Interference, Wavelength, and Velocity The purpose in this lab exercise is to become familiar with the properties of waves: frequency, wavelength, phase and velocity.

More information

Multi-Element Synthetic Transmit Aperture Method in Medical Ultrasound Imaging Ihor Trots, Yuriy Tasinkevych, Andrzej Nowicki and Marcin Lewandowski

Multi-Element Synthetic Transmit Aperture Method in Medical Ultrasound Imaging Ihor Trots, Yuriy Tasinkevych, Andrzej Nowicki and Marcin Lewandowski Multi-Element Synthetic Transmit Aperture Method in Medical Ultrasound Imaging Ihor Trots, Yuriy Tasinkevych, Andrzej Nowicki and Marcin Lewandowski Abstract The paper presents the multi-element synthetic

More information

MEASUREMENT OF RAYLEIGH WAVE ATTENUATION IN GRANITE USING

MEASUREMENT OF RAYLEIGH WAVE ATTENUATION IN GRANITE USING MEASUREMENT OF RAYLEIGH WAVE ATTENUATION IN GRANITE USING LASER ULTRASONICS Joseph O. Owino and Laurence J. Jacobs School of Civil and Environmental Engineering Georgia Institute of Technology Atlanta

More information

Structural UT: Variables Affecting Attenuation and Review of the 2 db per Inch Model

Structural UT: Variables Affecting Attenuation and Review of the 2 db per Inch Model Structural UT: Variables Affecting Attenuation and Review of the 2 db per Inch Model Paul Holloway, P.Eng, MASc, CGSB UT3 MT2 President, Holloway NDT & Engineering Inc. Purpose & Practical Applications

More information

The Law of Reflection

The Law of Reflection PHY132H1F Introduction to Physics II Class 5 Outline: Reflection and Refraction Fibre-Optics Colour and Dispersion Thin Lens Equation Image Formation Quick reading quiz.. virtual image is. the cause of

More information

Signal Characteristics

Signal Characteristics Data Transmission The successful transmission of data depends upon two factors:» The quality of the transmission signal» The characteristics of the transmission medium Some type of transmission medium

More information

LOS 1 LASER OPTICS SET

LOS 1 LASER OPTICS SET LOS 1 LASER OPTICS SET Contents 1 Introduction 3 2 Light interference 5 2.1 Light interference on a thin glass plate 6 2.2 Michelson s interferometer 7 3 Light diffraction 13 3.1 Light diffraction on a

More information

Propagation of pressure waves in the vicinity of a rigid inclusion submerged in a channel bounded by an elastic half-space

Propagation of pressure waves in the vicinity of a rigid inclusion submerged in a channel bounded by an elastic half-space Propagation of pressure waves in the vicinity of a rigid inclusion submerged in a channel bounded by an elastic half-space A. Tadeu, L. Godinho & J. Antonio Department of Civil Engineering University of

More information

Multi-spectral acoustical imaging

Multi-spectral acoustical imaging Multi-spectral acoustical imaging Kentaro NAKAMURA 1 ; Xinhua GUO 2 1 Tokyo Institute of Technology, Japan 2 University of Technology, China ABSTRACT Visualization of object through acoustic waves is generally

More information

Simulation of Ultrasonic Testing of Rail Wheel Face using Phased Array and DDF technique

Simulation of Ultrasonic Testing of Rail Wheel Face using Phased Array and DDF technique Simulation of Ultrasonic Testing of Rail Wheel Face using Phased Array and DDF technique Anand Desai, Ph.D. Abstract This paper presents a method of increasing the near surface resolution of a rail wheel

More information

Proceedings of Meetings on Acoustics

Proceedings of Meetings on Acoustics Proceedings of Meetings on Acoustics Volume 19, 2013 http://acousticalsociety.org/ ICA 2013 Montreal Montreal, Canada 2-7 June 2013 Signal Processing in Acoustics Session 1pSPa: Nearfield Acoustical Holography

More information

Isolation Scanner. Advanced evaluation of wellbore integrity

Isolation Scanner. Advanced evaluation of wellbore integrity Isolation Scanner Advanced evaluation of wellbore integrity Isolation Scanner* cement evaluation service integrates the conventional pulse-echo technique with flexural wave propagation to fully characterize

More information

CH 1. Large coil. Small coil. red. Function generator GND CH 2. black GND

CH 1. Large coil. Small coil. red. Function generator GND CH 2. black GND Experiment 6 Electromagnetic Induction "Concepts without factual content are empty; sense data without concepts are blind... The understanding cannot see. The senses cannot think. By their union only can

More information

Study of Standing Waves to Find Speed of Sound in Air

Study of Standing Waves to Find Speed of Sound in Air Study of Standing Waves to Find Speed of Sound in Air Purpose Using mobile devices as sound analyzer and sound generator to study standing waves and determine the speed of sound in air. Theory The velocity

More information

RECOMMENDATION ITU-R S.1528

RECOMMENDATION ITU-R S.1528 Rec. ITU-R S.158 1 RECOMMENDATION ITU-R S.158 Satellite antenna radiation patterns for non-geostationary orbit satellite antennas operating in the fixed-satellite service below 30 GHz (Question ITU-R 31/4)

More information

NUMERICAL MODELING OF AIR-COUPLED ULTRASOUND WITH EFIT. D. E. Chimenti Center of Nondestructive Evaluation Iowa State University Ames, Iowa, USA

NUMERICAL MODELING OF AIR-COUPLED ULTRASOUND WITH EFIT. D. E. Chimenti Center of Nondestructive Evaluation Iowa State University Ames, Iowa, USA NUMERICAL MODELING OF AIR-COUPLED ULTRASOUND WITH EFIT M. Rudolph, P. Fellinger and K. J. Langenberg Dept. Electrical Engineering University of Kassel 34109 Kassel, Germany D. E. Chimenti Center of Nondestructive

More information

Equipment for Attenuation and velocity of ultrasound in solid state materials (transmission), experimental set-up

Equipment for Attenuation and velocity of ultrasound in solid state materials (transmission), experimental set-up Attenuation and velocity of ultrasound in solid TEAS Related Topics Propagation of ultrasonic waves, time of flight, sound velocity, damping of ultrasonic waves (scattering, reflection, absorption), transmission

More information

Light diffraction by large amplitude ultrasonic waves in liquids

Light diffraction by large amplitude ultrasonic waves in liquids PROCEEDINGS of the 22 nd International Congress on Acoustics Ultrasound: Paper ICA2016-29 Light diffraction by large amplitude ultrasonic waves in liquids Laszlo Adler (a), John H. Cantrell (b), William

More information

Ground Penetrating Radar

Ground Penetrating Radar Ground Penetrating Radar Begin a new section: Electromagnetics First EM survey: GPR (Ground Penetrating Radar) Physical Property: Dielectric constant Electrical Permittivity EOSC 350 06 Slide Di-electric

More information

Finite element simulation of photoacoustic fiber optic sensors for surface rust detection on a steel rod

Finite element simulation of photoacoustic fiber optic sensors for surface rust detection on a steel rod Finite element simulation of photoacoustic fiber optic sensors for surface rust detection on a steel rod Qixiang Tang a, Jones Owusu Twumasi a, Jie Hu a, Xingwei Wang b and Tzuyang Yu a a Department of

More information

Traveling Waves. Why is there reflection? The one-dimensional (1D) case. A traveling wave is the propagation of motion (disturbance) in a medium.

Traveling Waves. Why is there reflection? The one-dimensional (1D) case. A traveling wave is the propagation of motion (disturbance) in a medium. The one-dimensional (1D) case Traveling Waves A traveling wave is the propagation of motion (disturbance) in a medium. Reflection Why is there reflection? The perturbation propagates on. Traveling Wave

More information

KULLIYYAH OF ENGINEERING

KULLIYYAH OF ENGINEERING KULLIYYAH OF ENGINEERING DEPARTMENT OF ELECTRICAL & COMPUTER ENGINEERING ANTENNA AND WAVE PROPAGATION LABORATORY (ECE 4103) EXPERIMENT NO 3 RADIATION PATTERN AND GAIN CHARACTERISTICS OF THE DISH (PARABOLIC)

More information

Implementation of decentralized active control of power transformer noise

Implementation of decentralized active control of power transformer noise Implementation of decentralized active control of power transformer noise P. Micheau, E. Leboucher, A. Berry G.A.U.S., Université de Sherbrooke, 25 boulevard de l Université,J1K 2R1, Québec, Canada Philippe.micheau@gme.usherb.ca

More information

Quantitative Crack Depth Study in Homogeneous Plates Using Simulated Lamb Waves.

Quantitative Crack Depth Study in Homogeneous Plates Using Simulated Lamb Waves. More Info at Open Access Database www.ndt.net/?id=18675 Quantitative Crack Depth Study in Homogeneous Plates Using Simulated Lamb Waves. Mohammad. (. SOORGEE, Aghil. YOUSEF)-KOMA Nondestructive Testing

More information

Ultrasonic Linear Array Medical Imaging System

Ultrasonic Linear Array Medical Imaging System Ultrasonic Linear Array Medical Imaging System R. K. Saha, S. Karmakar, S. Saha, M. Roy, S. Sarkar and S.K. Sen Microelectronics Division, Saha Institute of Nuclear Physics, 1/AF Bidhannagar, Kolkata-700064.

More information

EENG473 Mobile Communications Module 3 : Week # (12) Mobile Radio Propagation: Small-Scale Path Loss

EENG473 Mobile Communications Module 3 : Week # (12) Mobile Radio Propagation: Small-Scale Path Loss EENG473 Mobile Communications Module 3 : Week # (12) Mobile Radio Propagation: Small-Scale Path Loss Introduction Small-scale fading is used to describe the rapid fluctuation of the amplitude of a radio

More information

Physical Optics. Diffraction.

Physical Optics. Diffraction. Physical Optics. Diffraction. Interference Young s interference experiment Thin films Coherence and incoherence Michelson interferometer Wave-like characteristics of light Huygens-Fresnel principle Interference.

More information

Inquiring activities on the acoustic phenomena at the classroom using sound card in personal computer

Inquiring activities on the acoustic phenomena at the classroom using sound card in personal computer Inquiring activities on the acoustic phenomena at the classroom using sound card in personal computer Y.H. Kim Korea Science Academy, 111 Backyangkwanmoonro, Busanjin-ku, 614-822 Busan, Republic of Korea

More information

Medical Imaging. X-rays, CT/CAT scans, Ultrasound, Magnetic Resonance Imaging

Medical Imaging. X-rays, CT/CAT scans, Ultrasound, Magnetic Resonance Imaging Medical Imaging X-rays, CT/CAT scans, Ultrasound, Magnetic Resonance Imaging From: Physics for the IB Diploma Coursebook 6th Edition by Tsokos, Hoeben and Headlee And Higher Level Physics 2 nd Edition

More information

Absorption: in an OF, the loss of Optical power, resulting from conversion of that power into heat.

Absorption: in an OF, the loss of Optical power, resulting from conversion of that power into heat. Absorption: in an OF, the loss of Optical power, resulting from conversion of that power into heat. Scattering: The changes in direction of light confined within an OF, occurring due to imperfection in

More information

CONTACT LASER ULTRASONIC EVALUATION OF CONSTRUCTION MATERIALS

CONTACT LASER ULTRASONIC EVALUATION OF CONSTRUCTION MATERIALS CONTACT LASER ULTRASONIC EVALUATION OF CONSTRUCTION MATERIALS Alexander A.KARABUTOV 1, Elena V.SAVATEEVA 2, Alexei N. ZHARINOV 1, Alexander A.KARABUTOV 1 Jr. 1 International Laser Center of M.V.Lomonosov

More information

MEASUREMENT OF SURFACE ACOUSTIC WAVE USING AIR COUPLED TRANSDUCER AND LASER DOPPLER VIBROMETER

MEASUREMENT OF SURFACE ACOUSTIC WAVE USING AIR COUPLED TRANSDUCER AND LASER DOPPLER VIBROMETER 21 st International Conference on Composite Materials Xi an, 20-25 th August 2017 MEASUREMENT OF SURFACE ACOUSTIC WAVE USING AIR COUPLED TRANSDUCER AND LASER DOPPLER VIBROMETER Weitao Yuan 1, Jinfeng Zhao

More information

SUPPLEMENTARY INFORMATION

SUPPLEMENTARY INFORMATION Supplementary Information S1. Theory of TPQI in a lossy directional coupler Following Barnett, et al. [24], we start with the probability of detecting one photon in each output of a lossy, symmetric beam

More information

ISO INTERNATIONAL STANDARD. Non-destructive testing Acoustic emission inspection Secondary calibration of acoustic emission sensors

ISO INTERNATIONAL STANDARD. Non-destructive testing Acoustic emission inspection Secondary calibration of acoustic emission sensors INTERNATIONAL STANDARD ISO 12714 First edition 1999-07-15 Non-destructive testing Acoustic emission inspection Secondary calibration of acoustic emission sensors Essais non destructifs Contrôle par émission

More information

Factors Affecting Ultrasonic Waves Interacting with Fatigue Cracks

Factors Affecting Ultrasonic Waves Interacting with Fatigue Cracks Proceedings of the Interdisciplinary Workshop for Quantitative Flaw Definition, June 1974 Interdisciplinary Program for Quantitative Flaw Definition Annual Reports 1974 Factors Affecting Ultrasonic Waves

More information

Kirchhoff migration of ultrasonic images

Kirchhoff migration of ultrasonic images Kirchhoff migration of ultrasonic images Young-Fo Chang and Ren-Chin Ton Institute of Applied Geophysics, Institute of Seismology, National Chung Cheng University, Min-hsiung, Chiayi 621, Taiwan, R.O.C.

More information

A New Elastic-wave-based NDT System for Imaging Defects inside Concrete Structures

A New Elastic-wave-based NDT System for Imaging Defects inside Concrete Structures A New Elastic-wave-based NDT System for Imaging Defects inside Concrete Structures Jian-Hua Tong and Shu-Tao Liao Abstract In this paper, a new elastic-wave-based NDT system was proposed and then applied

More information

Implementation of electromagnetic acoustic resonance in pipe inspection

Implementation of electromagnetic acoustic resonance in pipe inspection E-Journal of Advanced Maintenance Vol.5-1(2013) 25-33 Implementation of electromagnetic acoustic resonance in pipe inspection Ryoichi URAYAMA 1 Toshiyuki TAKAGI 1,*, Tetsuya UCHIMOTO 1, Shigeru KANEMOTO

More information

Attenuation and velocity of ultrasound in solid state materials (transmission)

Attenuation and velocity of ultrasound in solid state materials (transmission) Attenuation and velocity of ultrasound in solid 5.1.6.08 Related Topics Propagation of ultrasonic waves, time of flight, sound velocity, damping of ultrasonic waves (scattering, reflection, absorption),

More information