Continuous Wave Laser Average Power Controller ADN2830
|
|
|
- Jacob Bryan
- 5 years ago
- Views:
Transcription
1 a FEATURES Bias Current Range 4 ma to 200 ma Monitor Photodiode Current 50 A to 1200 A Closed-Loop Control of Average Power Laser and Laser Alarms Automatic Laser Shutdown, Full Current Parameter Monitoring 5 V Operation 40 C to +85 C Temperature Range 5 mm 5 mm -Lead LFCSP Package APPLICATIONS Fiber Optic Communication Continuous Wave Laser Average Power Controller GENERAL DESCRIPTION The provides closed-loop control of the average optical power of a continuous wave (CW) laser diode () after initial factory setup. The control loop adjusts the laser to maintain a constant back facet monitor photodiode (MPD) current and thus a constant laser optical power. The external resistor is adjusted during factory setup to set the desired optical power. R is set at 1.23/I AV, where I AV is the MPD current corresponding to the desired optical power. Programmable alarms are provided for laser fail (end of life) and laser degrade (impending fail). To provide monitoring of the MPD current, the MPD can be connected to the pin. In this case, the MPD current is mirrored to the MON pin to provide a monitor and internally to the pin to close the control loop. By closing the feedback using rather than an MPD connected to, the device is configured to control a constant current in the laser rather than a constant optical output power. FUTIONAL BLOCK DIAGRAM MON MPD CONTROL R R Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective companies. One Technology Way, P.O. Box 9106, Norwood, MA , U.S.A. Tel: 781/ Fax: 781/ Analog Devices, Inc. All rights reserved.
2 SPECIFICATIONS Parameter Min Typ Max Unit Conditions/Comments LASER BIAS (BIAS) Output Current ma Compliance Voltage 1.2 V during 40 μa Response Time 10 μs MONITOR PD () Current μa Input Voltage 1.6 V POWER SET INPUT () Capacitance 80 pf Input Current μa Voltage V ALARM SET () Allowable Resistance Range kω Voltage V Hysteresis 5 % LOGIC INPUTS (, ) V IH 2.4 V V IL 0.8 V ALARM OUTPUTS (Internal 30 kω Pull-Up) V OH 2.4 V V OL 0.4 V MON, Division Ratio 100 A/A MON Division Ratio 1 A/A Compliance Voltage V SUPPLY 2 I CC 25 ma = V NOTES 1 Temperature range: 40 C to +85 C. 2 I CC for power calculation is the typical I CC given. Specifications subject to change without notice. ( = 5 V 10%. All specifications T MIN to T MAX, unless otherwise noted 1. Typical values as specified at 25 C.) 2
3 ABSOLUTE MAXIMUM RATINGS 1 (T A = 25 C, unless otherwise noted.) to V Digital Inputs (, Mode) V to V Operating Temperature Range Industrial C to +85 C Storage Temperature Range C to +150 C Junction Temperature (T J Max ) C θ JA Thermal Impedance C/W -Lead LFCSP Package, Power Dissipation (T J Max T A )/θ JA mw Lead Temperature (Soldering 10 sec) C NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 θ JA is defined when the part is soldered onto a 4-layer board. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE 3
4 PIN CONFIGURATION TOP VIEW PIN 1 INDICATOR = NO CONNECT MON THE EXPOSED PAD ON THE BOTTOM OF THE PACKAGE MUST BE CONNECTED TO VCC OR THE PLANE. PIN FUTION DESCRIPTIONS Pin No. Mnemonic Function 1 Supply Ground 2 Alarm Current Threshold Set Pin 3 No Connect 4 Average Optical Power Set Pin 5 Monitor Photodiode Input 6 MON Mirrored Current from Monitor Photodiode Current Source 7 4 Supply Ground 8 4 Supply Voltage 9 Average Power Loop Capacitor 10 Average Power Loop Capacitor 11 1 Supply Voltage 12 5 Supply Voltage 13 No Connect 14 1 Supply Ground 15 No Connect No Connect 17 Mode Select: Tied to = Standalone, High = Parallel Current Booster 18 Alarm Output 19 Alarm Output 20 Automatic Laser Shutdown 21 3 Supply Voltage 22 3 Supply Ground 23 Bias Current Monitor Output Current Source Bias Current Monitor Output Current Source 25 2 Supply Voltage 26 No Connect 27 Supply Ground 28 Laser Diode Bias Current 29 Supply Ground 30 Supply Ground 31 Laser Diode Bias Current No Connect EP Exposed Pad The exposed pad on the bottom of the package must be connected to VCC or the plane. 4
5 GENERAL Laser diodes have current-in to light-out transfer functions as shown in Figure 1. Two key characteristics of this transfer function are the threshold current, I TH, and slope in the linear region beyond the threshold current, referred to as slope efficiency (LI). Example: I = 50 ma, N = 1 I = 45 ma I TRIP 50 ma = = = 250 μa N OPTICAL POWER P AV I TH I P LI = P I CURRENT Figure 1. Laser Transfer Function CONTROL A monitor photodiode (MPD) is required to control the laser diode. The MPD current is fed into the to control the power, continuously adjusting the bias current in response to the laser s changing threshold current and light to current (LI) slope (slope efficiency). The uses automatic power control (APC) to maintain a constant power over time and temperature. The average power is controlled by the R resistor connected between the pin and ground. The pin is kept 1.23 V above. For an initial setup, the R resistor can be calculated using the following formula. V R = 123. I AV where I AV is average MPD current. Note the I will change from device to device. It is not required to know exact values for LI and MPD optical coupling. LOOP BANDWIDTH SELECTION Capacitor values greater than 22 nf are used to set the actual loop bandwidth. This capacitor is placed between the pin and ground. It is important that the capacitor is a low leakage multilayer ceramic with an insulation resistance greater than 100 GΩ or a time constant of 1000 sec, whichever is less. ALARMS The has two active high alarms, and. A resistor between ground and the pin is used to set the current at which these alarms are raised. The current through the resistor is a ratio of (N 200):1 to the alarm threshold (N is the number of s in parallel). The alarm will be raised at 90% of this level. *R = 123. V k I = A = 492. Ω μ The laser degrade alarm,, gives a warning of imminent laser failure if the laser diode degrades further or environmental conditions continue to stress the laser diode, e.g., increasing temperature. The laser fail alarm,, is activated when: The threshold is reached. The pin is set high. This shuts off the modulation and bias currents to the laser diode, resulting in the MPD current dropping to zero. will only be raised when the bias current exceeds 90% of the current. MONITOR CURRENTS and MON are current controlled current sources from. They mirror the bias and MPD current for increased monitoring functionality. An external resistor to gives a voltage proportional to the current monitored. If the MON function is not used, the pin must be grounded and the monitor photodiode must be tied directly to the pin. AUTOMATIC LASER SHUTDOWN When is logic high, the bias current is turned off. Correct operation of can be confirmed by the fail alarm being raised when is asserted. Note that this is the only time will be low while is high. The feature on the allows the user to operate more than one in parallel current boosting mode to achieve up to N 200 ma of bias current (N is the number of s in parallel). When using parallel boosting mode, one device is run as the master, the other as the slave. The pin on the master is tied to and the pin on the slave is tied high (see Figure 3 for reference circuit). ALARM INTERFACES The and outputs have an internal 30 kω pull-up resistor that is used to pull the digital high value to. However, the alarm output may be overdriven with an external resistor allowing the alarm interfacing to non- levels. Non- alarm output levels must be below the used for the. *The smallest value for R is 1.2 kω, as this corresponds to the maximum of N 200 ma. 5
6 POWER CONSUMPTION The die temperature must be kept below 125 C. The exposed paddle should be connected in such a manner that it is at the same potential as the ground pins. Power consumption can be calculated using the following formulas. T = T + P DIE AMBIENT θ J A I CC = I CCMIN ( ) P = V I + V CC CC BIAS_ PIN MPD F = NO CONNECT MON F PLACE CAP CLOSE TO PIN 8 Figure 2. Test Circuit, Standalone Mode, Input Not Used 6
7 MPD MON F PLACE CAP CLOSE TO PIN 8 = NO CONNECT MON 4 = NO CONNECT Figure 3. Test Circuit, Second Used in Parallel Current Boosting Mode to Achieve 400 ma Max 7
8 MPD R2 R MON F = NO CONNECT PLACE CAP CLOSE TO PIN 8 NOTES 1.FOR DIGITAL CONTROL, REPLACE R WITH A DIGITAL POTENTIOMETER FROM ANALOG DEVICES: ADN BIT RESOLUTION, 35 ppm/ C TC, EEPROM; AD52 8-BIT RESOLUTION, 30 ppm/ C TC. 2.TOTAL CURRENT TO LASER = + R1/R2. 3.FOR BEST ACCURACY, SIZE R1 TO HAVE A MAXIMUM VOLTAGE DROP ACROSS IT WITHIN THE HEADROOM CONSTRAINTS. 4.FOR 250 ma EXTRA (450 ma TOTAL) FROM AMP1, USE AD8591 AMPLIFIER. AMP1 IS THE OPERATIONAL AMPLIFIER SHOWN IN THIS FIGURE. 5.FOR 350 ma EXTRA (550 ma TOTAL) FROM AMP1, USE ANALOG DEVICES SSM2211 AMPLIFIER. AMP1 IS THE OPERATIONAL AMPLIFIER SHOWN IN THIS FIGURE. Figure 4. The Configured with Current Multiplier R2 CURRENT GAIN = R1 R2 AD820 MPD R1 2 = NO CONNECT 3 3 MON F PLACE CAP CLOSE TO PIN 8 Figure 5. The Configured as Average Power Controller (Bias Current Sourced) 8
9 2 3 3 MON 4 4 = NO CONNECT F PLACE CAP CLOSE TO PIN 8 Figure 6. The Configured as a Controlled Current Source by Feeding Back the Bias Monitor Current to R 9
10 OUTLINE DIMENSIONS PIN 1 INDICATOR SQ BSC EXPOSED PAD 1 PIN 1 INDICATOR SQ SEATING PLANE TOP VIEW MAX 0.02 NOM COPLANARITY REF 9 BOTTOM VIEW MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WHHD. Figure 7. -Lead Lead Frame Chip Scale Package [LFCSP_WQ] 5 mm 5 mm Body, Very Very Thin Quad (CP--7) Dimensions shown in millimeters ORDERING GUIDE Model 1 Temperature Range Package Description Package Option ACPZ 40 C to +85 C -Lead Lead Frame Chip Scale Package [LFCSP_WQ] CP--7 -EVALZ Evaluation Board 1 Z = RoHS Compliant Part A REVISION HISTORY 3/12 Rev. A to Rev. B Added EPAD Notation... 4 Updated Outline Dimensions Changes to Ordering Guide /03 Rev. 0 to Rev. A Changes to Absolute Maximum Ratings... 3 Updated Outline Dimensions Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D /12(B) 10
3 V Dual-Loop 50 Mbps to 1.25 Gbps Laser Diode Driver ADN2848
a FEATURES 50 Mbps to 1.25 Gbps Operation Single 3.3 V Operation Bias Current Range 2 ma to 100 ma Modulation Current Range 5 ma to 80 ma Monitor Photo Diode Current 50 A to 1200 A 50 ma Supply Current
3.3 V Dual-Loop 50 Mbps to 1.25 Gbps Laser Diode Driver ADN2848
Data Sheet FEATURES 50 Mbps to 1.25 Gbps operation Single 3.3 V operation Bias current range: 2 to 100 ma Modulation current range: 5 to 80 ma Monitor photo diode current: 50 μa to 1200 μa 50 ma supply
1 MHz to 8 GHz, 70 db Logarithmic Detector/Controller AD8318-EP
Enhanced Product FEATURES Wide bandwidth: MHz to 8 GHz High accuracy: ±. db over db range (f
1.2 V Precision Low Noise Shunt Voltage Reference ADR512
1.2 V Precision Low Noise Shunt Voltage Reference FEATURES Precision 1.200 V Voltage Reference Ultracompact 3 mm 3 mm SOT-23 Package No External Capacitor Required Low Output Noise: 4 V p-p (0.1 Hz to
OBSOLETE. Charge Pump Regulator for Color TFT Panel ADM8830
FEATURES 3 Output Voltages (+5.1 V, +15.3 V, 10.2 V) from One 3 V Input Supply Power Efficiency Optimized for Use with TFT in Mobile Phones Low Quiescent Current Low Shutdown Current (
9- and 11-Channel, Muxed Input LCD Reference Buffers AD8509/AD8511
9- and -Channel, Muxed Input LCD Reference Buffers AD8509/AD85 FEATURES Single-supply operation: 3.3 V to 6.5 V High output current: 300 ma Low supply current: 6 ma Stable with 000 pf loads Pin compatible
AD864/AD8642/AD8643 TABLE OF CONTENTS Specifications... 3 Electrical Characteristics... 3 Absolute Maximum Ratings... 5 ESD Caution... 5 Typical Perfo
FEATURES Low supply current: 25 µa max Very low input bias current: pa max Low offset voltage: 75 µv max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Unity-gain
Zero Drift, Digitally Programmable Instrumentation Amplifier AD8231-EP OP FUNCTIONAL BLOCK DIAGRAM FEATURES ENHANCED PRODUCT FEATURES
Zero Drift, Digitally Programmable Instrumentation Amplifier AD8231-EP FEATURES Digitally/pin-programmable gain G = 1, 2, 4, 8, 16, 32, 64, or 128 Specified from 55 C to +125 C 5 nv/ C maximum input offset
Ultrafast Comparators AD96685/AD96687
a FEATURES Fast: 2.5 ns Propagation Delay Low Power: 118 mw per Comparator Packages: DIP, SOIC, PLCC Power Supplies: +5 V, 5.2 V Logic Compatibility: ECL 50 ps Delay Dispersion APPLICATIONS High Speed
4 GHz to 18 GHz Divide-by-4 Prescaler ADF5001
4 GHz to 18 GHz Divide-by-4 Prescaler ADF5001 FEATURES Divide-by-4 prescaler High frequency operation: 4 GHz to 18 GHz Integrated RF decoupling capacitors Low power consumption Active mode: 30 ma Power-down
400 MHz 4000 MHz Low Noise Amplifier ADL5521
FEATURES Operation from 400 MHz to 4000 MHz Noise figure of 0.8 db at 900 MHz Including external input match Gain of 20.0 db at 900 MHz OIP3 of 37.7 dbm at 900 MHz P1dB of 22.0 dbm at 900 MHz Integrated
4 GHz to 18 GHz Divide-by-8 Prescaler ADF5002
4 GHz to 18 GHz Divide-by-8 Prescaler ADF5002 FEATURES Divide-by-8 prescaler High frequency operation: 4 GHz to 18 GHz Integrated RF decoupling capacitors Low power consumption Active mode: 30 ma Power-down
20 MHz to 6 GHz RF/IF Gain Block ADL5542
FEATURES Fixed gain of db Operation up to 6 GHz Input/output internally matched to Ω Integrated bias control circuit Output IP3 46 dbm at MHz 4 dbm at 9 MHz Output 1 db compression:.6 db at 9 MHz Noise
Logic Controlled, High-Side Power Switch with Reverse Current Blocking ADP195
Data Sheet Logic Controlled, High-Side Power Switch with Reverse Current Blocking ADP95 FEATURES Ultralow on resistance (RDSON) 5 mω @.6 V 55 mω @.5 V 65 mω @.8 V mω @. V Input voltage range:. V to.6 V.
3.3 V Dual-Loop 50 Mbps to 3.3 Gbps Laser Diode Driver ADN2847
Data Sheet FEATURES 50 Mbps to 3.3 Gbps operation Single 3.3 V operation Typical rise/fall time: 80 ps Bias current range: 2 ma to 00 ma Modulation current range: 5 ma to 80 ma Monitor photodiode current:
Octal, RS-232/RS-423 Line Driver ADM5170
a FEATURES Eight Single Ended Line Drivers in One Package Meets EIA Standard RS-3E, RS-3A and CCITT V./X. Resistor Programmable Slew Rate Wide Supply Voltage Range Low Power CMOS 3-State Outputs TTL/CMOS
20 MHz to 500 MHz IF Gain Block ADL5531
Data Sheet FEATURES Fixed gain of 20 db Operation up to 500 MHz Input/output internally matched to 50 Ω Integrated bias control circuit Output IP3 41 dbm at 70 MHz 39 dbm at 190 MHz Output 1 db compression:
Improved Second Source to the EL2020 ADEL2020
Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling
High Accuracy, Ultralow IQ, 1.5 A, anycap Low Dropout Regulator ADP3339
High Accuracy, Ultralow IQ, 1.5 A, anycap Low Dropout Regulator FEATURES High accuracy over line and load: ±.9% @ 25 C, ±1.5% over temperature Ultralow dropout voltage: 23 mv (typ) @ 1.5 A Requires only
Dual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
FET Drive Simple Sequencers ADM6819/ADM6820
FET Drive Simple Sequencers ADM6819/ADM682 FEATURES Single chip enables power supply sequencing of two supplies On-board charge pump fully enhances N-channel FET Adjustable primary supply monitor to.618
ADG1411/ADG1412/ADG1413
.5 Ω On Resistance, ±5 V/+2 V/±5 V, icmos, Quad SPST Switches ADG4/ADG42/ADG43 FEATURES.5 Ω on resistance.3 Ω on-resistance flatness. Ω on-resistance match between channels Continuous current per channel
High Isolation, Silicon SPDT, Nonreflective Switch, 0.1 GHz to 6.0 GHz HMC8038W
5 6 7 8 6 5 4 3 FEATURES Nonreflective, 50 Ω design High isolation: 60 db typical Low insertion loss: 0.8 db typical High power handling 34 dbm through path 29 dbm terminated path High linearity P0.dB:
Programmable Low Voltage 1:10 LVDS Clock Driver ADN4670
Data Sheet Programmable Low Voltage 1:10 LVDS Clock Driver FEATURES FUNCTIONAL BLOCK DIAGRAM Low output skew
Dual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
0.8% Accurate Quad Voltage Monitor ADM1184
.8% Accurate Quad Voltage Monitor ADM1184 FEATURES Powered from 2.7 V to 5.5 V on the VCC pin Monitors 4 supplies via.8% accurate comparators 4 inputs can be programmed to monitor different voltage levels
CMOS Switched-Capacitor Voltage Converters ADM660/ADM8660
CMOS Switched-Capacitor Voltage Converters ADM66/ADM866 FEATURES ADM66: Inverts or Doubles Input Supply Voltage ADM866: Inverts Input Supply Voltage ma Output Current Shutdown Function (ADM866) 2.2 F or
DC to 1000 MHz IF Gain Block ADL5530
DC to MHz IF Gain Block ADL3 FEATURES Fixed gain of 6. db Operation up to MHz 37 dbm Output Third-Order Intercept (OIP3) 3 db noise figure Input/output internally matched to Ω Stable temperature and power
Low Power, Rail-to-Rail Output, Precision JFET Amplifiers AD8641/AD8642/AD8643
Data Sheet Low Power, Rail-to-Rail Output, Precision JFET Amplifiers AD864/AD8642/AD8643 FEATURES Low supply current: 25 μa max Very low input bias current: pa max Low offset voltage: 75 μv max Single-supply
Triple, 6-Channel LCD Timing Delay-Locked Loop AD8389
Triple, 6-Channel LCD Timing Delay-Locked Loop PRODUCT FEATURES High speed Up to 85 MHz clock rate Triple (R, G, B) output Matched delay lines Low power dissipation: 40 mw Reference to rising or falling
100 MHz to 4000 MHz RF/IF Digitally Controlled VGA ADL5240
1 MHz to 4 MHz RF/IF Digitally Controlled VGA ADL524 FEATURES Operating frequency from 1 MHz to 4 MHz Digitally controlled VGA with serial and parallel interfaces 6-bit,.5 db digital step attenuator 31.5
1:2 Single-Ended, Low Cost, Active RF Splitter ADA4304-2
FEATURES Ideal for CATV and terrestrial applications Excellent frequency response.6 GHz, 3 db bandwidth db flatness to. GHz Low noise figure: 4. db Low distortion Composite second order (CSO): 62 dbc Composite
DC to 1000 MHz IF Gain Block ADL5530
Data Sheet FEATURES Fixed gain of 16. db Operation up to MHz 37 dbm Output Third-Order Intercept (OIP3) 3 db noise figure Input/output internally matched to Ω Stable temperature and power supply 3 V or
High Speed 12-Bit Monolithic D/A Converters AD565A/AD566A
a FEATURES Single Chip Construction Very High Speed Settling to 1/2 AD565A: 250 ns max AD566A: 350 ns max Full-Scale Switching Time: 30 ns Guaranteed for Operation with 12 V (565A) Supplies, with 12 V
Triple, 6-Channel LCD Timing Delay-Locked Loop AD8389 PRODUCT FEATURES High speed Up to 85 MHz clock rate Triple (R, G, B) output Matched delay lines
Triple, 6-Channel LCD Timing Delay-Locked Loop PRODUCT FEATURES High speed Up to 85 MHz clock rate Triple (R, G, B) output Matched delay lines Low power dissipation: 40 mw Reference to rising or falling
Micropower Precision CMOS Operational Amplifier AD8500
Micropower Precision CMOS Operational Amplifier AD85 FEATURES Supply current: μa maximum Offset voltage: mv maximum Single-supply or dual-supply operation Rail-to-rail input and output No phase reversal
Self-Contained Audio Preamplifier SSM2019
a FEATURES Excellent Noise Performance:. nv/ Hz or.5 db Noise Figure Ultra-low THD:
400 MHz to 4000 MHz Low Noise Amplifier ADL5523
FEATURES Operation from MHz to MHz Noise figure of. db at 9 MHz Requires few external components Integrated active bias control circuit Integrated dc blocking capacitors Adjustable bias for low power applications
ADA485-/ADA485- TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... Specifications... 3 Spe
NC NC NC NC 5 6 7 8 6 NC 4 PD 3 PD FEATURES Ultralow power-down current: 5 na/amplifier maximum Low quiescent current:.4 ma/amplifier High speed 75 MHz, 3 db bandwidth V/μs slew rate 85 ns settling time
9.25 GHz to GHz MMIC VCO with Half Frequency Output HMC1162
9.5 GHz to 10.10 GHz MMIC VCO with Half Frequency Output HMC116 FEATURES FUTIONAL BLOCK DIAGRAM Dual output f OUT = 9.5 GHz to 10.10 GHz f OUT / = 4.65 GHz to 5.050 GHz Power output (P OUT ): 11 dbm (typical)
Comparators and Reference Circuits ADCMP350/ADCMP354/ADCMP356
Data Sheet Comparators and Reference Circuits ADCMP35/ADCMP354/ADCMP356 FEATURES Comparators with.6 V on-chip references Output stages Open-drain active low (ADCMP35) Open-drain active high (ADCMP354)
150 μv Maximum Offset Voltage Op Amp OP07D
5 μv Maximum Offset Voltage Op Amp OP7D FEATURES Low offset voltage: 5 µv max Input offset drift:.5 µv/ C max Low noise:.25 μv p-p High gain CMRR and PSRR: 5 db min Low supply current:. ma Wide supply
+5 V Fixed, Adjustable Low-Dropout Linear Voltage Regulator ADP3367*
a FEATURES Low Dropout: 50 mv @ 200 ma Low Dropout: 300 mv @ 300 ma Low Power CMOS: 7 A Quiescent Current Shutdown Mode: 0.2 A Quiescent Current 300 ma Output Current Guaranteed Pin Compatible with MAX667
CMOS, 170 MHz, Triple, 10-Bit High Speed Video DAC ADV7123-EP
CMOS, 70 MHz, Triple, 0-Bit High Speed Video DAC ADV723-EP FEATURES 70 MSPS throughput rate Triple, 0-bit digital-to-analog converters (DACs) SFDR 70 db at fclk = 50 MHz; fout = MHz 53 db at fclk = 40
1.2 V Precision Low Noise Shunt Voltage Reference ADR512W
1.2 V Precision Low Noise Shunt Voltage Reference ADR512W FEATURES Precision 1.200 V voltage reference Ultracompact 3-lead SOT-23 package No external capacitor required Low output noise: 4 µv p-p (0.1
OBSOLETE. Simple Sequencers in 6-Lead SC70 ADM1088. Data Sheet
Data Sheet Simple Sequencers in 6-Lead SC7 FEATURES Provide programmable time delays between enable signals Can be cascaded with power modules for multiple supply sequencing Power supply monitoring from.6
20 MHz to 500 MHz IF Gain Block ADL5531
20 MHz to 500 MHz IF Gain Block ADL5531 FEATURES Fixed gain of 20 db Operation up to 500 MHz Input/output internally matched to 50 Ω Integrated bias control circuit Output IP3 41 dbm at 70 MHz 39 dbm at
12.92 GHz to GHz MMIC VCO with Half Frequency Output HMC1169
Data Sheet 12.92 GHz to 14.07 GHz MMIC VCO with Half Frequency Output FEATURES Dual output frequency range fout = 12.92 GHz to 14.07 GHz fout/2 = 6.46 GHz to 7.035 GHz Output power (POUT): 11.5 dbm SSB
High Accuracy, Ultralow IQ, 1 A, anycap Low Dropout Regulator ADP3338
High Accuracy, Ultralow IQ, 1 A, anycap Low Dropout Regulator FEATURES High accuracy over line and load: ±.8% @ 25 C, ±1.4% over temperature Ultralow dropout voltage: 19 mv (typ) @ 1 A Requires only CO
Octal, RS-232/RS-423 Line Driver ADM5170
a FEATURES Eight Single Ended Line Drivers in One Package Meets EIA Standard RS-3E, RS-3A and CCITT V./X. Resistor Programmable Slew Rate Wide Supply Voltage Range Low Power CMOS 3-State Outputs TTL/CMOS
+5 V Powered RS-232/RS-422 Transceiver AD7306
a FEATURES RS-3 and RS- on One Chip Single + V Supply. F Capacitors Short Circuit Protection Excellent Noise Immunity Low Power BiCMOS Technology High Speed, Low Skew RS- Operation C to + C Operations
High Accuracy Ultralow I Q, 300 ma, anycap Low Dropout Regulator ADP3333
High Accuracy Ultralow I Q, 3 ma, anycap Low Dropout Regulator ADP3333 FEATURES FUNCTIONAL BLOCK DIAGRAM High accuracy over line and load: ±.8% @ 5 C, ±.8% over temperature Ultralow dropout voltage: 3
12.17 GHz to GHz MMIC VCO with Half Frequency Output HMC1167
9 0 3 4 5 6 9 7 6.7 GHz to 3.33 GHz MMIC VCO with Half Frequency Output FEATURES Dual output frequency range fout =.7 GHz to 3.330 GHz fout/ = 6.085 GHz to 6.665 GHz Output power (POUT): 0.5 dbm Single-sideband
High Isolation, Silicon SP4T, Nonreflective Switch, 9 khz to 12.0 GHz ADRF5040
RF4 RF3 7 8 9 1 11 12 21 2 19 RF2 High Isolation, Silicon SP4T, Nonreflective Switch, 9 khz to 12. GHz ADRF54 FEATURES FUNCTIONAL BLOCK DIAGRAM Nonreflective 5 Ω design Positive control range: V to 3.3
11.41 GHz to GHz MMIC VCO with Half Frequency Output HMC1166
9 6 3 30 29 VTUNE 28 27 26.4 GHz to 2.62 GHz MMIC VCO with Half Frequency Output FEATURES Dual output frequency range fout =.4 GHz to 2.62 GHz fout/2 = 5.705 GHz to 6.3 GHz Output power (POUT): dbm Single-sideband
High Accuracy Ultralow I Q, 500 ma anycap Adjustable Low Dropout Regulator ADP3336
a FEATURES High Accuracy Over Line and Load:.9% @ 5 C,.8% Over Temperature Ultralow Dropout Voltage: mv (Typ) @ 5 ma Requires Only C O =. F for Stability anycap = Stable with Any Type of Capacitor (Including
Four White LED Backlight Driver ADM8843
Data Sheet FEATURES Drives 4 LEDs from a.6 V to 5.5 V (Li-Ion) input supply /.5 / fractional charge pump to maximize power efficiency 0.3% typical LED current matching Up to 88% power efficiency over Li-Ion
Microprocessor Supervisory Circuit ADM1232
Microprocessor Supervisory Circuit FEATURES Pin-compatible with MAX1232 and Dallas DS1232 Adjustable precision voltage monitor with 4.5 V and 4.75 V options Adjustable strobe monitor with 150 ms, 600 ms,
AD MHz, 20 V/μs, G = 1, 10, 100, 1000 i CMOS Programmable Gain Instrumentation Amplifier. Preliminary Technical Data FEATURES
Preliminary Technical Data 0 MHz, 20 V/μs, G =, 0, 00, 000 i CMOS Programmable Gain Instrumentation Amplifier FEATURES Small package: 0-lead MSOP Programmable gains:, 0, 00, 000 Digital or pin-programmable
320 ma Switched Capacitor Voltage Doubler ADP3610
a FEATURES Push-Pull Charge Pump Doubler Reduces Output Ripple 3.0 V to 3.6 V Operation > 5.4 V @ 320 ma Maximum Load Output Impedance, R TOTAL 1.66 Shutdown Capability Overvoltage Protection: > 4 V Operating
Dual Low Power 1.5% Comparator With 400 mv Reference ADCMP670
Dual Low Power.5% Comparator With mv Reference ADCMP67 FEATURES FUNCTIONAL BLOCK DIAGRAM mv ±.5% threshold Supply range:.7 V to 5.5 V Low quiescent current: 6.5 μa typical Input range includes ground Internal
VOUT = 5V VIN = 8V COUT CIN SENSE RPG EN/ UVLO OFF GND VOUT = 5V VIN = 8V CIN ADJ RPG EN/ UVLO OFF GND
956-2 956-1 VIN = 8V OFF ON CIN 1µF R1 1kΩ R2 1kΩ + VIN EN/ UVLO GND VOUT SENSE PG + COUT 1µF VOUT = 5V RPG 1kΩ PG VIN = 8V OFF ON CIN 1µF R3 1kΩ R4 1kΩ + VIN EN/ UVLO GND VOUT ADJ PG R1 4.2kΩ R2 13kΩ
Precision, Low Power, Micropower Dual Operational Amplifier OP290
a FEATURES Single-/Dual-Supply Operation, 1. V to 3 V,. V to 1 V True Single-Supply Operation; Input and Output Voltage Ranges Include Ground Low Supply Current (Per Amplifier), A Max High Output Drive,
Single-Supply, High Speed, Triple Op Amp with Charge Pump ADA4858-3
Single-Supply, High Speed, Triple Op Amp with Charge Pump FEATURES Integrated charge pump Supply range: 3 V to 5.5 V Output range: 3.3 V to.8 V 5 ma maximum output current for external use at 3 V High
Rail-to-Rail, High Output Current Amplifier AD8397
Rail-to-Rail, High Output Current Amplifier FEATURES Dual operational amplifier Voltage feedback Wide supply range from 3 V to 24 V Rail-to-rail output Output swing to within.5 V of supply rails High linear
Single 0.275% Comparator and Reference with Dual Polarity Outputs ADCMP361
Data Sheet FEATURES mv ±.275% threshold Supply range:.7 V to 5.5 V Low quiescent current: 6.5 µa typical Input range includes ground Internal hysteresis: 9.3 mv typical Low input bias current: ±5 na maximum
Low Voltage, 400 MHz, Quad 2:1 Mux with 3 ns Switching Time ADG774A
Data Sheet FEATURES Bandwidth: >4 MHz Low insertion loss and on resistance: 2.2 Ω typical On resistance flatness:.3 Ω typical Single 3 V/5 V supply operation Very low distortion:
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5
30 MHz to 6 GHz RF/IF Gain Block ADL5611
Data Sheet FEATURES Fixed gain of 22.2 db Broad operation from 3 MHz to 6 GHz High dynamic range gain block Input and output internally matched to Ω Integrated bias circuit OIP3 of 4. dbm at 9 MHz P1dB
Dual Processor Supervisors with Watchdog ADM13305
Dual Processor Supervisors with Watchdog ADM335 FEATURES Dual supervisory circuits Supply voltage range of 2.7 V to 5.5 V Pretrimmed threshold options:.8 V, 2.5 V, 3.3 V, and 5 V Adjustable.6 V voltage
High Precision 10 V Reference AD587
High Precision V Reference FEATURES Laser trimmed to high accuracy.000 V ± 5 mv (U grade) Trimmed temperature coefficient 5 ppm/ C maximum (U grade) Noise-reduction capability Low quiescent current: ma
Triple Processor Supervisors ADM13307
Triple Processor Supervisors ADM337 FEATURES Triple supervisory circuits Supply voltage range of 2. V to 5.5 V Pretrimmed threshold options:.8 V, 2.5 V, 3.3 V, and 5 V Adjustable.6 V and.25 V voltage references
1.0 V Precision Low Noise Shunt Voltage Reference ADR510
1.0 V Precision Low Noise Shunt Voltage Reference FEATURES Precision 1.000 V voltage reference Ultracompact 3 mm 3 mm SOT-23 package No external capacitor required Low output noise: 4 μv p-p (0.1 Hz to
15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP
5 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +25 C) Controlled manufacturing baseline
Low Voltage, 400 MHz, Quad 2:1 Mux with 3 ns Switching Time ADG774A
Low Voltage, 4 MHz, Quad 2:1 Mux with 3 ns Switching Time FEATURES Bandwidth: >4 MHz Low insertion loss and on resistance: 2.2 Ω typical On resistance flatness:.3 Ω typical Single 3 V/5 V supply operation
Integer-N Clock Translator for Wireline Communications AD9550
Integer-N Clock Translator for Wireline Communications AD955 FEATURES BASIC BLOCK DIAGRAM Converts preset standard input frequencies to standard output frequencies Input frequencies from 8 khz to 2 MHz
Single and Dual, Ultralow Distortion, Ultralow Noise Op Amps AD8597/AD8599 PIN CONFIGURATIONS FEATURES APPLICATIONS
Single and Dual, Ultralow Distortion, Ultralow Noise Op Amps FEATURES Low noise:. nv/ Hz at khz Low distortion: db THD @ khz Input noise,. Hz to Hz:
ADG1606/ADG Ω RON, 16-Channel, Differential 8-Channel, ±5 V,+12 V,+5 V, and +3.3 V Multiplexers FEATURES FUNCTIONAL BLOCK DIAGRAMS
4.5 Ω RON, 6-Channel, Differential 8-Channel, ±5 V,+2 V,+5 V, and +3.3 V Multiplexers ADG66/ADG67 FEATURES 4.5 Ω typical on resistance. Ω on resistance flatness ±3.3 V to ±8 V dual supply operation 3.3
Very Low Distortion, Precision Difference Amplifier AD8274
Very Low Distortion, Precision Difference Amplifier AD8274 FEATURES Very low distortion.2% THD + N (2 khz).% THD + N ( khz) Drives Ω loads Excellent gain accuracy.3% maximum gain error 2 ppm/ C maximum
30 MHz to 6 GHz RF/IF Gain Block ADL5610
Data Sheet FEATURES Fixed gain of 18.4 db Broad operation from 3 MHz to 6 GHz High dynamic range gain block Input and output internally matched to Ω Integrated bias circuit OIP3 of 38.8 dbm at 9 MHz P1dB
ADM6823. Low Voltage, Supervisory Circuit with Watchdog and Manual Reset in 5-Lead SOT-23. Data Sheet FUNCTIONAL BLOCK DIAGRAM FEATURES APPLICATIONS
Data Sheet Low Voltage, Supervisory Circuit with Watchdog and Manual Reset in 5-Lead SOT-23 FEATURES Precision low voltage monitoring 9 reset threshold options: 1.58 V to 4.63 V (typical) 140 ms (minimum)
Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD8276
Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD87 FEATURES Wide input range Rugged input overvoltage protection Low supply current: μa maximum Low power dissipation:. mw at VS
0.4 Ω CMOS, Dual DPDT Switch in WLCSP/LFCSP/TSSOP ADG888
FEATURES.8 V to 5.5 V operation Ultralow on resistance.4 Ω typical.6 Ω maximum at 5 V supply Excellent audio performance, ultralow distortion.7 Ω typical.4 Ω maximum RON flatness High current carrying
50 ma, High Voltage, Micropower Linear Regulator ADP1720
5 ma, High Voltage, Micropower Linear Regulator ADP72 FEATURES Wide input voltage range: 4 V to 28 V Maximum output current: 5 ma Low light load current: 28 μa at μa load 35 μa at μa load Low shutdown
1 MHz to 2.7 GHz RF Gain Block AD8354
Data Sheet FEATURES Fixed gain of 2 db Operational frequency of 1 MHz to 2.7 GHz Linear output power up to 4 dbm Input/output internally matched to Ω Temperature and power supply stable Noise figure: 4.2
High Precision 10 V Reference AD587
High Precision V Reference FEATURES Laser trimmed to high accuracy.000 V ±5 mv (L and U grades) Trimmed temperature coefficient 5 ppm/ C max (L and U grades) Noise reduction capability Low quiescent current:
OBSOLETE. Active RF Splitter ADA FEATURES FUNCTIONAL BLOCK DIAGRAM APPLICATIONS GENERAL DESCRIPTION
FEATURES Single V supply 4 MHz to 86 MHz CATV operating range 4.6 db of gain per output channel 4.4 db noise figure 2 db isolation between output channels 16 db input return loss CSO of 73 dbc (13 channels,
30 MHz to 6 GHz RF/IF Gain Block ADL5611
Preliminary Technical Data FEATURES Fixed gain of 22.1 db Broad operation from 30 MHz to 6 GHz High dynamic range gain block Input/output internally matched to 50 Ω Integrated bias control circuit OIP3
Two Selectable Inputs, 8 LVPECL Outputs, SiGe Clock Fanout Buffer ADCLK948
Data Sheet Two Selectable Inputs, 8 LVPECL Outputs, SiGe Clock Fanout Buffer FEATURES 2 selectable differential inputs 4.8 GHz operating frequency 75 fs rms broadband random jitter On-chip input terminations
OBSOLETE. Ultrahigh Speed Window Comparator with Latch AD1317
a FEATURES Full Window Comparator 2.0 pf max Input Capacitance 9 V max Differential Input Voltage 2.5 ns Propagation Delays Low Dispersion Low Input Bias Current Independent Latch Function Input Inhibit
2300 MHz to 2900 MHz Balanced Mixer, LO Buffer and RF Balun ADL5363
Data Sheet 2300 MHz to 2900 MHz Balanced Mixer, LO Buffer and RF Balun FEATURES RF frequency range of 2300 MHz to 2900 MHz IF frequency range of dc to 450 MHz Power conversion loss: 7.7 db SSB noise figure
Supervisory Circuits with Watchdog and Manual Reset in 5-Lead SC70 and SOT-23 ADM823/ADM824/ADM825
Data Sheet Supervisory Circuits with Watchdog and Manual Reset in 5-Lead SC70 and SOT-23 ADM823/ADM824/ADM825 FEATURES FUNCTIONAL BLOCK DIAGRAM Precision 2.5 V to 5 V power supply monitor 7 reset threshold
1.2 V Precision Low Noise Shunt Voltage Reference ADR512
FEATURES Precision 1.200 V Voltage Reference Ultracompact 3 mm 3 mm SOT-23 Package No External Capacitor Required Low Output Noise: 4 µv p-p (0.1 Hz to 10 Hz) Initial Accuracy: ±0.3% Max Temperature Coefficient:
ADG918/ADG919. Wideband 4 GHz, 43 db Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, 2:1 Mux/SPDT Switches
Wideband 4 GHz, 43 db Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, 2:1 Mux/SPDT Switches ADG918/ FEATURES Wideband switch: 3 db @ 4 GHz Absorptive/reflective switches High off isolation (43 db @ 1 GHz) Low
1 MHz to 10 GHz, 45 db Log Detector/Controller AD8319
FEATURES Wide bandwidth: 1 MHz to 10 GHz High accuracy: ±1.0 db over temperature 45 db dynamic range up to 8 GHz Stability over temperature: ±0.5 db Low noise measurement/controller output VOUT Pulse response
Switched Capacitor Voltage Converter with Regulated Output ADP3603*
a FEATURES Fully Regulated Output High Output Current: ma ma Version (ADP6) Is Also Available Outstanding Precision: % Output Accuracy Input Voltage Range: +. V to +6. V Output Voltage:. V (Regulated)
Dual Picoampere Input Current Bipolar Op Amp AD706. Data Sheet. Figure 1. Input Bias Current vs. Temperature
Data Sheet Dual Picoampere Input Current Bipolar Op Amp Rev. F Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by
Low Cost 100 g Single Axis Accelerometer with Analog Output ADXL190*
a FEATURES imems Single Chip IC Accelerometer 40 Milli-g Resolution Low Power ma 400 Hz Bandwidth +5.0 V Single Supply Operation 000 g Shock Survival APPLICATIONS Shock and Vibration Measurement Machine
Ultralow Power Voltage Comparator with Reference ADCMP380
Data Sheet Ultralow Power Voltage Comparator with Reference FEATURES Comparator with on-chip reference Ultralow power consumption with ICC = 92 na (typical) Precision low voltage monitoring down to.5 V