LDL2-146X30SW. CCS Inc. 2x4-M3 depth 5. Five slots for M3 nuts

Transcription

1 LDL-14XSW x4-m3 depth Model name LED color Connector Polarity and signal Third Angle Projection 1..5 LDL-14XSW DC4V 1W 1g SMR-03V-B 1 : (+), : NC, 3 : ( _ ) Units: mm Five slots for M3 nuts Copyright(c) 09 CCS Inc. All rights reserved. Reproduction or photocopy without permission is prohibited. CCS Inc.

2 Common Specifications LED color Peak wavelength (typ.) Relative color temperature (typ.) Cable length Input connector Polarity, signal Case material Operating temperature and humidity Storage temperature and humidity Cooling method Spectral distribution Relative irradiation strength (%) (RD) (SW) (BL) (GR) nm 4 nm 55 nm,00 K max. 0.3 m SMR-03V-B 1: Anode (+) brown, : NC, 3: Cathode ( ) blue Aluminum alloy Temperature: 0 to C, Humidity: % to 85% (with no condensation) Temperature: - to 0 C, Humidity: % to 85% (with no condensation) Natural air cooling Wavelength (nm) Use an R0-series sharp-cut filter. Patent Pending Note: The values for irradiation strength and service life given in this catalog are for reference purposes. These values are not ensured. Precautions Carefully read the product's instruction manual before use to ensure correct operation. Product specifications and design are subject to change without notice. Examples of workpiece imaging in this catalog are a guide that may be informative for choosing Light Units. Please check the functions of the equipment and requirements before choosing a Light Unit. New Generation LED Bar Light New Bar Light Units with Direct Illumination Full Model Change The New LDL Series Headquarters Shimodachiuri-agaru, Karasuma-dori, Kamigyo-ku, Kyoto 0-11 Japan Phone: / Fax: Copyright(c) 09 CCS Inc. All Rights Reserved. URL: intlsales@ccs-inc.co.jp Descriptions in this catalog are based on information available as of October LDL

3 Full Model Change Five New s 1 New Mounting Method The new mounting method enables versatile mounting to match the installation environment. Frame structure Mounting tap holes Cable side The cable is flat to the mounting surface, and so mounting can be made to any surface. High Output Enhanced Output with Improved Light Emission Efficiency Heat Dissipation Enhanced You can select from two methods for greater mounting versatility to match your installation environments: the new frame structure mounting method or the conventional mounting holes. With the new mounting method, you have freedom in adjusting the lighting position and mounting location by sliding the securing nuts into the internal grooves in the frame structure. The size of the internal grooves complies with JIS standard M3 nuts, which are commonly used. (Use JIS standard M3 nuts for mounting.) Selectable Directional Characteristics 3 Stable long-term performance with high-efficiency heat dissipation product (red) LDL (red) Enhanced Heat Dissipation LED Section Temperature Change Graph Temperature ( C) 0 0 Decrease of approx. % Using heat radiating fins and the frame structure increases the surface area by % over the previous model. This enables a decrease by approximately % of the LED mounting section temperature due to highly efficient heat radiation. 4 Enhanced Customizability Maximum emission surface size of 0 mm. mm mm One-lens unit: 39 mm One-lens unit: 4 mm Emission surface size 9 mm max. Model with -mm-wide emission surface Emission surface size mm max. Model with -mm-wide emission surface Using one lens of a standardized size enables flexible customizability. The specified length of light unit can be produced in the unit of one lens. Note: For other lengths, contact your CCS sales representative. A brightness of approximately five times is achieved over previous products for red light with a camera. Brightness has also been enhanced for white, blue, and green light. Light Product (%) Light LDL (%) Note: 1)This applies for each color using the narrow model. Comparison of image capture LDL The brightness depends on the spectral sensitivity characteristics of the camera. Two models are available with different directional characteristics: the narrow model, which uses the original lens with directional characteristics similar to previous models, and a wide model, which has diffuse illumination in a wide range. Directional Characteristics of Narrow Model ( Light) Larger emission surface 1 Original lens Angle (deg.) Directional Characteristics of Wide Model ( Light) Larger emission surface Angle (deg.) The wide model can provide uniform illumination in a wide area, which offers new usage of bar light. We recommend this new method using Bar Light Units LWD = mm Illumination LWD = mm Diffusion LDL (narrow model) Product Brightness distribution Brightness increased by approximately five times with a camera. Brightness increased by approximately 1.7 times with a camera. Light Product LDL (%) Shutter speed: 1/1,000 Brightness increased by approximately 1. times with a camera. Brightness distribution Light Brightness increased Product by approximately (SW Series) 1.8 times with a camera (%) LWD = 0 mm Camera Camera Shutter speed: 1/1,000 Shutter speed: 1/4,000 Note; 1)Relative sensor brightness distribution measurement conditions: Intensity: 0%, Lens: F-mm, Width: 775 mm, Field of vision: 3 x 7 mm 3)The values given here are for reference purposes. Actual values may vary. LDL )The brightness of each color depends on the spectral sensitivity characteristics of the camera. Brightness increased by approximately four times with a camera even for a wide area. LDL-XRD-WD Shutter speed: 1/4,000 LDL-XRD-WD 0 Output level (%) Illumination LWD = 0 mm Diffusion Brightness distribution Relative irradiation strength Relative irradiation strength Shutter speed: 1/0 Brightness distribution Brightness increased by approximately four times with a camera even for a wide area. LDL-XRD-WD Shutter speed: 1/,000 LDL-XRD-WD Shutter speed: 1/0 Shutter speed: 1/,000 )The brightness depends on the spectral sensitivity characteristics of the camera. 0 Output level (%) 5 4-V Input For All Colors The power that is supplied is the same for all light colors. ly, 1 V was used only for red light, but the voltage is now for all colors. Data Relative irradiation strength (%) LDL-41XRD-WD ( Light) Temperature ( C) Typical Examples. There are virtually no changes in the graph values for the narrow model or changes that depend on whether optional products are mounted. Actual values were measured using the LDL-41XRD-WD. (These values are for reference only.) Change in Temperature over Time Stable at approx. C 0 0 Bottom of case External air temperature Change in Irradiation Output over Time 0 0 Range of fluctuation: % Relative irradiation strength (%) LDL-41XSW-WD ( Light) Actual values were measured using the LDL-41XSW-WD. (These values are for reference only.) Temperature ( C) Change in Temperature over Time Stable at approx. 38 C 0 0 Bottom of case Change in Irradiation Output over Time 0 0 External air temperature Range of fluctuation: 1% Note: Graph measurement conditions: Actual measurement values: Intensity: 0%, External air temperature: C (These values are for reference only.) 1

4 Options The and have been redesigned to use insertion fixing rather than the previous screw fixing method. Upgraded materials for the improve the rate of diffusion. is available protect the emission area of the Light Unit as well as bracketss for securing the Light Unit to enable flexible adjustment of the emission direction. Diffusion Mounting Light Fixing Brackets Mounting DF-LDL Series Insert the tabs into the side grooves. (for all models in Series) Install the bracketss on both ends of the Light Unit. Specifications of Special Options Name The irradiated light is diffused to limit workpiece glare and reflections. Model name (for both narrow model and wide model) Accessories Removal Fixing screws (M3): (spare) Heat resistance C 0 C C Two types of are available. Use combinations for the following cases. Mounting with Emission from Four Directions Example DF-LDL-41X DF-LDL-X DF-LDL-119X DF-LDL-74X DF-LDL-14X DF-LDL-18X DF-LDL-X PL-LDL-41X Use a combination of two pairs of the two types. PL-LDL-41X-VE The polarization direction differs by 90. PL-LDL-41X(-VE) PL-LDL-X(-VE) PL-LDL-119X(-VE) PL-LDL-74X(-VE) PL-LDL-14X(-VE) PL-LDL-18X(-VE) PL-LDL-X(-VE) Black Polarization PL-LDL Series CV-LDL-41X CV-LDL-X CV-LDL-119X CV-LDL-74X CV-LDL-14X CV-LDL-18X CV-LDL-X The light is polarized. You can prevent light reflection by fixing a PL-series polarization filter to the lens. Protective CV-LDL Series For details, refer to the instruction manual. When you secure the light, the angle of the irradiation can be adjusted as desired. A variety of methods are available for securing the Light Units, such as parallel emission from two directions or enveloped emission from four directions. Adjust the emission angle and then firmly secure the Light Unit. (for all models in Series) Differentiating Paired s Not black Paired s will turn black when they overlap in opposite directions and will not be black when they overlap in the same direction. Dimensional diagrams (mm) DF/PL/CV-LDL Series -mm-wide models (3.) (Bilaterally Symmetric) dia. The plate protects the emission section of the Light Unit Note: The is not intended to provide protection against dust or water droplets. Use a flat-blade screwdriver or other tool with a narrow point to catch the tabs and remove the For details, refer to the instruction manual. -mm-wide models Two, -dia. holes 1 3. R9 90 (37.) (90 ). 8.4 Product Lineup The standard lineup now includes models with a length of 0 mm or more as well as models with an emission surface of mm. The lineup includes combination of over models with light colors in red, white, blue, and green, various sizes, and narrow models or wide models. You can easily access information for the desired product by visiting the CCS website (Machine Vision Applications) and entering the seven-digit number into the direct number input space. Model with -mm-wide emission surface Model with -mm-wide emission surface Direct number Model LDL-41XRD LDL-41XSW LDL-41XBL LDL-41XGR LDL-41XRD-WD LDL-41XSW-WD LDL-41XBL-WD LDL-41XGR-WD LDL-XRD LDL-XSW LDL-XBL LDL-XGR LDL-XRD-WD LDL-XSW-WD LDL-XBL-WD LDL-XGR-WD LDL-119XRD LDL-119XSW LDL-119XBL LDL-119XGR LDL-119XRD-WD LDL-119XSW-WD LDL-119XBL-WD LDL-119XGR-WD LDL-74XRD LDL-74XSW LDL-74XBL LDL-74XGR LDL-74XRD-WD LDL-74XSW-WD LDL-74XBL-WD LDL-74XGR-WD LDL-14XRD LDL-14XSW LDL-14XBL LDL-14XGR LDL-14XRD-WD LDL-14XSW-WD LDL-14XBL-WD LDL-14XGR-WD LDL-18XRD LDL-18XSW LDL-18XBL LDL-18XGR LDL-18XRD-WD LDL-18XSW-WD LDL-18XBL-WD LDL-18XGR-WD LDL-XRD LDL-XSW LDL-XBL LDL-XGR LDL-XRD-WD LDL-XSW-WD LDL-XBL-WD LDL-XGR-WD LED color Emission surface size 41x mm 41x mm x mm x mm 119x mm 119x mm 74x mm 74x mm 14x mm 14x mm 18x mm 18x mm x mm x mm Power consumption 1.9 W 1.9 W 3.8 W 3.8 W 1 W 18 W 1 W 1 W g g 75 g 75 g 95 g 95 g 0 g 0 g 1 g 1 W 1 g g 18 W g g g Light fixing Brackets Supported options DF-LDL-41X PL-LDL-41X (PL-LDL-41X-VE) CV-LDL-41X DF-LDL-41X PL-LDL-41X (PL-LDL-41X-VE) CV-LDL-41X DF-LDL-X PL-LDL-X (PL-LDL-X-VE) CV-LDL-X DF-LDL-X PL-LDL-X (PL-LDL-X-VE) CV-LDL-X DF-LDL-119X PL-LDL-119X (PL-LDL-119X-VE) CV-LDL-119X DF-LDL-119X PL-LDL-119X (PL-LDL-119X-VE) CV-LDL-119X DF-LDL-74X PL-LDL-74X (PL-LDL-74X-VE) CV-LDL-74X DF-LDL-74X PL-LDL-74X (PL-LDL-74X-VE) CV-LDL-74X DF-LDL-14X PL-LDL-14X (PL-LDL-14X-VE) CV-LDL-14X DF-LDL-14X PL-LDL-14X (PL-LDL-14X-VE) CV-LDL-14X DF-LDL-18X PL-LDL-18X (PL-LDL-18X-VE) CV-LDL-18X DF-LDL-18X PL-LDL-18X (PL-LDL-18X-VE) CV-LDL-18X DF-LDL-X PL-LDL-X (PL-LDL-X-VE) CV-LDL-X DF-LDL-X PL-LDL-X (PL-LDL-X-VE) CV-LDL-X 3 4

5 Dimensional diagrams (mm) Model with -mm-wide emission surface Model with -mm-wide emission surface LDL-74XRD/SW/BL/GR (compatible with -WD models) LDL-41XRD/SW/BL/GR (compatible with -WD models) x, M3, Depth: 5 Slot for three, M3 nuts 8 74 x 4, M3, Depth: LDL-XRD/SW/BL/GR (compatible with -WD models) 9 x, M3, Depth: LDL-14XRD/SW/BL/GR (compatible with -WD models) x 4, M3, Depth: Slot for three, M3 nuts 1..5 LDL-18XRD/SW/BL/GR (compatible with -WD models) 18 x 4, M3, Depth: 5 (same for opposite side) 7 7 LDL-119XRD/SW/BL/GR (compatible with -WD models) x, M3, Depth: 5 Slot for three, M3 nuts 1..5 LDL-XRD/SW/BL/GR (compatible with -WD models) 78 x 4, M3, Depth: 5 (same for opposite side)

6 EN085-1:1994+A1:0+A:01 Direct Lighting Bar Lights Thank you for purchasing a CCS product. To ensure proper use of the product, please read this instruction guide before use and keep it for your future reference. 1.Introduction.Important Information for Equipment Safety Incorrect usage of the product may result in fire, electric shock, or other serious damages. Please ensure to follow the conditions below. Symbol Descriptions Warning Caution Symbol Examples FIRE HAZARD DISASSEMBLY UNPLUG LDL Series Instruction Guide This product is an LED light used for machine vision and industrial inspection. Do not use the product for other applications, and be sure to follow the instructions below. Do not use the product in the following situations. Under conditions or in an environment not described in this instruction guide. In nuclear energy control systems, railroad systems, aviation systems, vehicles, combustion equipment, medical equipment, amusement machines, or safety equipment. In applications involving serious risk to life or property, particularly applications demanding a high level of safety. Use and Storage temperrature and humidity Use the product only in the following environment. Operating temperature and humidity (indoors only) Storage temperature and humidity Installation location Please install products to locations with following conditions. Incorrect installation location may cause product failure. In a flat and stable location with minimal vibration. Well-ventilated places with minimal dust. Places that are not subject to sudden temperature changes. Temperature: 0 to C, Humidity: to 85%RH (with no condensation) Temperature: - to 0 C, Humidity: to 85%RH (with no condensation) Places free from any water, oil, liquid, chemical, or steam. Places free from corrosive or combustible gas. Places away from water faucets, boilers, humidifiers, air conditioners, heaters, or stoves. symbols indicate caution (also including danger and warning). The example shown here indicates a fire caution. symbols indicate prohibited acts. The example shown here indicates prohibition to disassemble. -Read Before Use- Indicates that incorrect usage may result in serious injury or death. Indicates that incorrect usage may result in injury or property damage. symbols indicate instructions for specific actions. The example shown here indicates that the power cord must be disconnected. 4.Installation Installation on a Frame M3 nut Side installation Installation Using a Tap Hole Direct Installation Caution Fixing screw Fixing screw Frame Insert the M3 nut into the slit in the frame. Rear installation Tap hole for installation Provided on both sides. Required Parts Installation with M3 nut (conforming to JIS) Fixing Screws (M3) Required Parts :Fixing Screws (M3) (Optional product) Model: (Common for all LDL series.) Fixing screw Reference! Read the LDL series Operation Guide for Optional Products before using optional products. The tap holes on the back surface are for factory use. Do not use them for installation..specifications Common Specifications LED color (RD) (SW) (BL) (GR) 4V max. Peak wavelength (typ.) 35nm 4nm 55nm Relative color temperature (typ.) 00K Cable 0.3m Connector SMR-03V-B Polarity and signal 1: Anode (+) brown, : NC, 3: Cathode (-) blue Case material Aluminum alloy Cooling method Natural air cooling LDL-41x Series LDL-x Series LDL-119x Series 1.9W max. g 3.8W max. 75g 5.7W max. 95g LDL-74x Series LDL-14x Series LDL-18x Series LDL-x Series 5.7W max. 0g 1W max. 1g 18W max. g 1W max. g 8.EU RoHS Directive The RoHS Directive is short for the "restriction of use of certain hazardous substances in electrical and electronic equipment." As a directive, it restricts the use of specific hazardous substances for new electrical and electronic equipment marketed in the EU on or after July 1, 0, and restricts the use of six substances, which are (1) lead, () mercury, (3) cadmium, (4) hexavalent chromium, (5) polybrominated biphenyl (PBB), and () polybrominated diphenyl ether (PBDE). *Standards for "RoHS Directive-Compliant Products" (Items that are exempted in the RoHS Directive are excluded from these standards.) 9.China RoHS Directive China RoHS Directive is formally known as "Management Methods for Controlling Pollution by Electronic Information Products", which was implemented on March 1, 07 in China. Same as EU RoHS Directive, this regulation restricts the usage of six substances such as lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyl (PBB), and polybrominated diphenyl ether (PBDE). This regulation requires electronic information products which are manufactured or imported, and sold in China, to clearly disclose contents of the restricted substances listed below. 环保使用期限 Lead Mercury Cadmium Hexavalent chromium PBB PBDE 00ppm Min 00ppm Min 0ppm Min 00ppm Min 00ppm Min 00ppm Min Usage Deadline for Environmental Protection Name and amount of toxic and hazardous substances or elements, which products contain Product name LED Lights 产品 LED 照明 Lead (Pb) Mercury (Hg) Toxic or Hazardous Substances and Elements Cadmium (Cd) 产品中有毒有害物质或元素的名称及含量 有毒有害物质或元素 Hexavalent chromium (Cr(VI)) : Indicates that this toxic or hazardous substances contained in all the homogeneous materials for this part, according to SJ/T is within the limit requirement. : Indicates that this toxic or hazardous substance contained in all the homogeneous materials for this part, according to SJ/T1133-0, is over the limit requirement. *Lead and cadmium are excluded in EU RoHS. Usage deadline for environmental protection The number used in this logo is based on Management Methods for Controlling Pollution by Electronic Information Products and related regulations from People s Republic of China. It shows the product usage duration in years for environmental protection. After finishing a product usage, the product need to be re-used or discard appropriately following local law and regulations, complying with safety and usage caution. 铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr(VI)) 多溴联苯 (PBB) 多溴二苯醚 (PBDE) : 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 标准规定的限量要求以下 : 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 标准规定的限量要求 ( 注 ) 铅和镉中的, 因欧洲 RoHS 没限定, 故用 表示 环保使用期限此标志的数字是根据中华人民共和国电子信息产品污染控制管理办法以及有关标准等, 表示该产品的环保使用期限的年数 遵守产品的安全和使用上的注意, 在产品使用后采取适当的方法根据各地法律, 规定, 回收再利用或进行废弃处理.Laser Safety Standards (IEC085-1 Amd.) LED illumination devices are laser products as stipulated by IEC (International Electrotechnical Commission) and JIS (Japanese Standards Association). A brief summary of the hazard classes is provided below. PBB PBDE Warning LED light radiation may cause corneal or retinal abnormalities if you look directly at the light. To prevent harmful light exposure, never look directly at the LED light. Do not disassemble or modify the product. Doing so may result in fire or electric shock. DISASSEMBLY This product generates high temperatures. Do not touch the product while it is turned on or immediately after it is turned off, or burning may result. Provide cooling with a fan or other ventilation if the product is to be used in a closed space. BE CAREFUL OF HIGH TEMPERATURES Do not touch the product with wet hands. Doing so may result in electric shock. Make sure that the product is free of moisture or any liquid. Exposure to water may result in fire, electric shock, or product failure. - - BE CAREFUL OF THE LIGHT BEAM DO NOT TOUCH WITH SET HANDS DO NOT SUBJECT TO MOISTURE Connect or disconnect the light cable only after turning off the power supply for the LED light. Failure to do so may result in circuit damage, fire caused by a minute spark, or electric shock. FIRE HAZARD SHOCK HAZARD If abnormal condition occurs such as fuming, heat, smell, noise, or so on, stop using the product immediately, and turn the power off. A fire or electric shock may result if the product is kept used. Do not use user-made cables. Doing so may cause product failure. Use the optional extension cable if it is necesszary to extend the distance between the light and the power supply. Make sure that the length of the extension cable is less than 5m. If the extension cable is longer than 5m, the voltage applied to both ends of the LED light will drop due to the DC resistance of the cable. The rated voltage will not be attained for 0% radiant ability, and the radiant quantity will drop as a result. 3.Product Information INSTRUCTION Caution Do not drop the product or subject it to impact. Doing so may cause the product to malfunction. Be careful of static electricity. Damage to the LED light may occur, if a person charged with static electricity touches it. Keep the product away from all items charged with static electricity. UNPLUG The product is provided with a tag specifying the class of risk, maximum output, and wavelength of LED light. The surface of the tag is classified by color according to the luminescence color. The back of the tag specifies the model name, power consumption, and serial number. Tag surface (Example) LED RADIATION AVOID EXPOSURE TO BEAM MAX POWER:7mW WAVE LENGTH:7nm CLASS LED PRODUCT The right illustration shows the attachment position of the tag. Be sure to check the contents before using the product and handle the tag with care. If the tag is missing or damaged and the contents cannot be checked, please contact CCS Inc. Close-up LED RADIATION AVOID EXPOSURE TO BEAM MAX POWER:7mW WAVE LENGTH:7nm CLASS LED PRODUCT EN085-1:1994+A1:0+A:01 Tag Back (Example) LDL-74X V/5.7W MADE IN JAPAN Items described on tag 5.Operating Instructions Wire Connection 1 Make sure that the power is turned OFF. Connect light cable to power supply output connector. Light side Capture Images 1 Turn the power on. The Light will come on. Lighting at a Fixed Angle Power supply side Lighting When Using the Light Fixing Brackets (Optional product) Model: (Used for all Series.) The lighting angle is adjustable. Reference! Read the instruction guide of the power supply for the LED light before use. INSTRUCTION Insert the connector completely. Preparations! Focus imaging devices such as cameras, microscopes, etc. to inspection objects. Adjustment! Adjust light range, light angle, and light quantity to optimize images. Note:Use the power supply for the LED light to adjust the radiant quantity. Reference! Read the LDL series Operation Guide for Optional Products before using optional products. Other Applications Backlight Lighting Using a Diffusion plate (Optional product) Model:DF-LDL series 7.Dimensional diagrams (mm) LDL-nxRD/SW/BL/GR (Common for all WD models.) (A=53,9,131) (B=41,,119) (n=b) (Emitting A B(Emitting x-m3depth 5 (Provided on both sides) Three slots for three M3 nuts LDL-nxRD/SW/BL/GR (Common for all WD models.) (A=8,158,,78) (B=74,14,18,) (n=b) (Emitting A B(Emitting x4-m3depth 5 (Provided on both sides) () Five slots for M3 nuts 1..5 Class Class Warranty Information Outline of risk evaluation Low-output visible light (0 to 0 nm): The eyes are generally protected by an aversion reaction, such as blinking. EXCEPT FOR THE EXPRESS WARRANTIES STATED IN THIS AGREEMENT, COMPANY MAKES NO ADDTIONANAL WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, AS TO ANY MATTER WHATSOEVER. IN PARTICULAR, ANY AN ALL WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED. EXCEPT AS EXPRESSLY SET FORTH HEREIN, COMPANY MAKES NO WARRANTIES WITH RESPECT TO THE PRODUCTS. WARRANTY PERIOD: TWO YEARS (ONE YEAR FOR RADIANT QUANTITY), STARTING FROM CCS Inc. SHIPPING DATE. CCS Inc. WILL REPAIR OR REPLACE THE PRODUCT FREE OF CHARGE IF IT SHOULD FAIL TO FUNCTION OR IF THE RADIANT QUANTITY OF THE PRODUCT SHOULD DROP TO % OR LESS OF ITS INITIAL RADIANT QUANTITY WITHIN THE SPECIFIED WARRANTY PERIOD. IF EITHER OF THESE CONDITIONS OCCURS, PLEASE TAKE THE PRODUCT TO YOUR CCS SALES REPRESENTATIVE. WARRANTY TERMS 1 CCS Inc. WILL REPAIR OR REPLACE THE PRODUCT FREE OF CHARGE IF IT SHOULD FAIL TO FUNCTION UNDER USE ON OUR SPECIFIED CONDITION IN ACCORDANCE WITH THE INSTRUCTION GUIDE AND OTHER WRITTEN CAUTIONS DURING THE INDICATED WARRANTY PERIOD OF TWO YEARS. CCS Inc. WILL REPAIR OR REPLACE THE PRODUCT FREE OF CHARGE IF ITS RADIANT QUANTITY SHOULD DROP TO % OR LESS OF ITS INITIAL RADIANT QUANTITY UNDER USE ON OUR SPECIFIED CONDITION IN ACCORDANCE WITH THE INSTRUCTION GUIDE AND OTHER WRITTEN CAUTIONS DURING THE INDICATED WARRANTY PERIOD OF ONE YEAR. 3 CCS Inc. WILL CHARGE A REPAIR FEE UNDER THE FOLLOWING CONDITIONS: 1) IF THE PRODUCT HAS BEEN SUBJECTED TO MISUSE, UNAUTHORIZED REPAIRS, OR MODIFICATION FROM ITS ORIGINAL DESIGN. ) IF THE PRODUCT HAS BEEN DAMAGED FROM IMPACTS DUE TO INAPPROPRIATE HANDLING. 3) IF DAMAGE TO THE PRODUCT RESULTS FROM EXTERNAL CAUSES INCLUDING ACCIDENTS, FIRE, POLLUTION, RIOTS, COMMUNICATION FAILURES, EARTHQUAKES, THUNDERSTORMS, WIND AND FLOOD DAMAGE, OR ANY OTHER ACT OF PROVIDENCE, OR FROM ANY EXTRAORDINARY CONDITIONS SUCH AS ELECTRICAL SURGES, WATER LEAKAGE, CONDENSATION, OR THE USE OF CHEMICALS. 4) IF THE DAMAGE RESULTS FROM CONNECTION TO ANY POWER SUPPLY OR TO ANY EQUIPMENT WHICH CCS Inc. DOES NOT MANUFACTURE OR DOES NOT SPECIFY FOR USE. 4 CCS ASSUMES NO LIABILITY FOR ANY PURCHASER S SECONDARY DAMAGE (DAMAGE OF EQUIPMENT, LOSS OF OPPORTUNITIES, LOSS OF PROFITS, ETC.) OR ANY OTHER DAMAGE RESULTING FROM A FAILURE OF OUR PRODUCT. THIS WARRANTY INFORMATION PROVIDES THE SCOPE OF CCS'S PRODUCT WARRANTY WITHIN THE SPECIFIED PERIOD, AND DOES NOT INDICATE OR IMPLY ANY FURTHER GUARANTEE BEYOND THE WARRANTY TERMS. CONTACT CCS FOR INQUIRIES OR INFORMATION ON REPAIRS TO THE PRODUCT AFTER THE EXPIRATION OF THE WARRANTY. NOTE: THE RADIANT QUANTITY REFERS TO THE WATTAGE OF PHYSICAL ENERGY RADIATED FROM A LED. IT REFERS TO THE RADIATION LUMINOSITY OF THE LED MEASURED UNDER CONDITIONS SPECIFIED BY CCS OR THE RADIATION ILLUMINATION OF THE LED UNDER SPECIFIED IRRADIATION CONDITIONS. CCS SPECIFIES THE RADIANT QUANTITY FOR EACH LED LIGHT BECAUSE THE MEASUREMENT AND IRRADIATION CONDITIONS VARY FROM THE FORM, THE APPLICATION AND THE IRRADIATION WAVELENGTH. Please contact CCS for product information, and further information. The Instruction Guide is available from CCS's website as well. Headquarters Shimodachiuri-agaru, Karasuma-dori, Kamigyo-ku,Kyoto 0-11 Japan Phone : Fax : intlsales@ccs-inc.co.jp Diffusion plates, polarizing plates, and protective Copyright(c) 09 CCS Inc. All Rights Reserved. plates cannot be stacked for installation or used Descriptions in this instruction guide are based on information available as of February 09. KZ0438-T together