More to Prior than meets the eye. Nikon. Automation Guide. Nikon Automation Guide
|
|
- Jewel Page
- 5 years ago
- Views:
Transcription
1 More to Prior than meets the eye Nikon Automation Guide Nikon Automation Guide
2 Introduction This brochure is designed to provide an overview of the equipment we produce for a range of Nikon microscopes. Please note that the equipment in this guide is not an exhaustive list and instead shows the more common products that can be mounted on these microscopes. Additionally, other Nikon microscopes can have Prior equipment added to them. More information about our products can be found by contacting a Prior representative, ing uksales@prior.com or by visiting We also have an extensive collection of datasheets which are freely available on our website ( or via contacting Prior Scientific. The parts to be selected will depend both upon the microscope make and the end-user s application. We highly recommend contacting a Prior Sales Manager before ordering. At the end of this guide you will find a short explanation of our stage codes. 1 Nikon Automation Guide
3 Contents Nikon FN1 3 Nikon Ti/Ti2 7 Nikon Ni (Focussing Stage) 11 Nikon NI (Focussing Nosepiece) 15 Nikon AZ Nikon SMZ 18/25 23 Nikon LV100 and LV Nikon L200 and L Nikon TS2R 35 Nikon Ci 39 Nikon MA Nikon MA Nikon ProZ Stand 49 Stage Guide 53 Products listed in green on the systems charts require the ProScan III Control System to be operated Please note that the parts may vary in availability and part numbers and specifications may change without warning. Whilst we have attempted to verify that the information here is accurate, we cannot guarantee that it is completely up to date and error free; thus we suggest contacting Prior before ordering in order to ensure that all equipment will be compatible with your microscope and suitable for your application. The microscopes featured here are for illustrative purposes only. All intellectual property relating to these microscopes, including patents and trademarks, remain the property of their respective owners. Nikon is a registered trademark of Nikon Corporation. ProScan, OptiScan and ZDeck and the Prior Scientific logo are registered trademarks of Prior Scientific Ltd. The 5 year warranty applies to stages used only with a Prior controller, for full details, terms and conditions of the warranty please visit This document is Prior Scientific Nikon Sales Brochure July 2017 V
4 Nikon FNI Slide Loader - PL PL238 2 OR PL PL304 - PL310 Post Sample Holder - HZP HZP HZP1020 HZP Post Mounts - HZP150 - HZP200 - HZP250 - HZP300 Translation Stage - ZDP50T - ZDP50K Sample holders - H224LP - H224PLP - H234LP Motorised stages - H101NFN - HIP4NFN - HEP4NFN - PL101NFN - PLE01NFN Z-Deck Sample Holders - HZ202 - HZ203 (HZ201 adapter Z-Deck - ZDN12MP - ZDN12ME - ZDN12MK - ZDN12MF NanoScanZ 3 - NZ200F 3 Nikon Automation Guide
5 Nikon FNI Lumen L220SNI - L200SNI Lumen L100###NI (Replace ### with wavelength) Filter wheels - HF108A/HF220 (Excitation) - HF110A/HF220 (Excitation) Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF Shutters - HF200HT (Excitation) - HF201HT (Excitation) Brightfield - LDB103NI - LDB10FNI Joystick Control Unit - PS3J100 Lumen L220NI - L200NI Focus Motor - NIKRFK + NIKFN1MA - NIKRFK + NIKFN1EK -PS3H122R + H
6 Nikon FNI Product ES10ZE H101NFN H1P4NFN H224LP H224PLP H234LP HEP4NFN HF108A/HF220 HF110A/HF220 HF200HT HF201HT HZ201 HZ202 HZ203 H3940 HZP150 HZP200 HZP250 HZP300 HZP1000 HZP1010 HZP1020 L100###NI L200NI L200SNI L220NI L220SNI Details Focus only controller H101A stage with 2mm screw pitch and 200 step motor H101A stage with 1 mm screw pitch and 400 step motor Low profile slide holder Low profile slide holder (71 x 51 mm slide holder) Low profile slide holder for 4 71 x 21 mm slides H101A stage with 1mm screw pitch, 400 step motor and encoders 8 position 32 mm filter wheel with adapter 10 position 25 mm filter wheel with adapter High speed shutter with 25 mm aperture High speed shutter with 32 mm aperture Adapter allowing upright sample holders to be inserted into Z-Deck Solid Insert Plate for Z-Deck 108 mm ring insert plate for Z-Deck Adapter to connect PS3H122R focus motor to FN1 microscope Rigid post mount 150 mm tall Rigid post mount 200 mm tall Rigid post mount 250 mm tall Rigid post mount 300 mm tall Manipulator holder for HZP150/200/250/300 Standard sample holder for HZP150/200/250/300 Circular holder for HZP150/200/250/300 Single LED illumination system. Replace ### with wavelength required. Metal Halide Illumination Source Metal Halide Illumination Source with integral shutter. Metal Halide Illumination Source with extended UV/IR wavelengths Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengths 5 Nikon Automation Guide
7 Nikon FNI Product Details LDB102NI Brightfield Illumination LED for Nikon (standalone) LDB103NI Brightfield Illumination LED for Nikon (ProScan control) NIKFN1EK Adapter for Nikon FN1 for NIKRFK (encoded) NIKFN1MA Adapter for Nikon FN1 for NIKRFK NIKRFK Nikon remote focussing kit - includes controller, cables and focus motor NZ200F NanoScanZ (adapted for flat top stages) PL200 Slide Loader PL228 Bevel edged sample holder for 1 x 3 slides. Includes 4 slide racks for for 1 x 3 slides PL238 Bevel edged sample holder for 2 x3 slides. Includes 2 slide racks for 2 x 3 slides PL310 Elevated baseplate to improve clearance PL304 Barcode reader for PL200 PL101NFN H101A stage for use with slide loader PLE01NFN Encoded H101A stage for use with Slide Loader (use with PL228 only) PS3J100 Multifunctional manual joystick for ProScan PS3H122R Generic focus motor; requires H3940 focus adapter. V31F ProScan controller with three stepper drives for focus and two filter wheels or 3 shutters V31XYZE ProScan controller with XYZ drives and encoder input V31XYZEF ProScan controller with XYZ drives, three filter wheel drives, shutter drives and encoder input ZDN12MP Motorised Z-Deck quick adjust platform system ZDN12ME Motorised Z-Deck quick adjust platform system (Encoded) ZDN12MK Manual Z-Deck quick adjust platform system ZDN12MF Fixed plate Z-Deck quick adjust platform system ZDP50K Translation stage for microscope (manual) ZDP50T Translation stage for microscope (motorised). Includes OptiScan controller Notes 1) The slide loader can only be used with the PL101FN or PLE01FN stages 2) The PLE01FN is only for use with the PL228 3) The NZ200F can only be used with the Z-Deck 6
8 Nikon Ti/Ti2 NanoScanZ Sample holders - NZ303 (NZ400) - NZ302 (NZ400) - NZ301 (NZ400) NanoScan Z stages - NZ400 Sample holders - H473XR - H223XRNC - H229XR -H224XRLP NanoScanZ Incubation Chambers - W3719 (NZ400) Motorised stages - H117P1N4 - H117E1N4 Option to add H117ACCM Incubation chambers - W4184 Linear stages - HLD117NN (HLD324 adapter required for use of Prior Sample Holders) Well Plate Loader - PLW20N - PLW106 H139 Sample holders - H171XR - H223XR2 - H473R3 Two wellplate stages - H139P1NN - H139E1N5 7 Nikon Automation Guide
9 Nikon Ti/Ti2 Brightfield - LDB103NI - LDB102NI Nikon Ti Hub Integration kit - LDBNHUB Lumen L100###NI (Replace ### with wavelength) Lumen L220SNI - L200SNI Filter wheels - HF110A + HF220 (Excitation) - HF110A + HF255 (Emission) - HF108A + HF248 (Emission) - HF108A + HF220 (Excitation) - HF6NTK (Motorised turret) - HF110/32A + HF220 (Excitation) - HF110/32A + HF255 (emission) Shutters - HF200HT (Excitation) - HF201HT (Excitation) - HF202HT + HF220 (Excitation) - HF204HT + HF220 (Excitation) Lumen L220NI - L200NI Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF - VLD31XYZ - VLD31XYZEF Focus Motor - PS3H122R + H2975 / H122KON Joystick Control Unit - PS3J
10 Nikon Ti/Ti2 Product ES10ZE ACCM H117E1N4 H117P1N4 H139P1NN H139E1N5 H171XR H122KON H223XRNC H223XR2 H224XRLP H229XR H473XR H473XR3 HF108A/HF220 HF110A/HF220 HF110A/HF255 HF108A/HF248 HF11032A/HF220 HF11032A/HF255 HF200HT HF201HT HF202HT/HF220 HF204HT/HF220 HF6NTK HLD117NN HLD324 HLW223XR L100###NI L200NI L200SNI L220NI L220SNI Details Focus only system controller Extension plates for H117 stages H117 motorised stage with 1mm screw pitch and encoders H117 motorised stage with 1mm screw pitch H139 motorised stage with 1 mm ballscrew, 400 stepper motor H139 motorised stage with 1 mm ballscrew, 400 stepper motor and 50 nm encoder 9 Slide holder for H139 Direct fine focussing kit for Nikon and Olympus Microscopes Extra recessed low profile microtitre plate for H117 stages 2 micro titre plate holder from H139 Extra recessed low profile slide holder for H117 stages Extra recessed petri dish holder for H117 stages Extra recessed low profile universal holder for H117 stages Double Universal Sample Holder for H139 Filter wheel holding 8 32 mm filters with adapter (Excitation) Filter wheel holding 10 25mm filters with adapter (Excitation) Filter wheel holding 10 25mm filters with adapter (Emission) Filter wheel mounted underneath nosepiece (Emission) Filter wheel holding mm filters with adapter (Excitation) Filter wheel holding mm filters with adapter (Emission) High speed shutter with 25mm aperture for use with filter wheel High speed shutter with 32mm aperture for use with filter wheel High speed shutter with 25mm aperture for stand alone use, with adapter High speed shutter with 32mm aperture for stand alone use, with adapter Upgrade to motorised turret allowing control via ProScan Linear motor stage with travel range of 81 x 121 mm and 50 nm encoders Required to adapt linear stages for Prior insert Required to adapt linear stages for the PLW20. Check with Nikon for condenser and objective compatibility Single LED illumination system. Replace ### with wavelength required Metal Halide Illumination Source Metal Halide Illumination Source with integral shutter Metal Halide Illumination Source with extended UV/IR wavelengths Metal Halide Illumination Source with integral shutter and with extended UV/IR wavelengths 9 Nikon Automation Guide
11 Nikon Ti/Ti2 Product LDB102NI LDB103NI LDBNHUB NZ301 NZ302 NZ303 NZ400 PS3H122R/H2975 PS3J100 PLW106 PLW107 PLW20 V31F V31XYZE V31XYZEF VLD31XYZ VLD31XYZF W3569 W3719 W4184 Details Brightfield Illumination LED for Nikon (standalone) Brightfield Illumination LED for Nikon (ProScan control) Integrates the Brightfield into the Nikon Ti Hub Extra recessed well plate holder for NZ400 Extra recessed slide/petri dish holder for NZ400 Extra recessed slide holder for NZ400 Nanopositioning piezo Z stage with 400 um of travel and controller Focus drive and adapter Multifunctional manual joystick for ProScan Barcode reader for Well Plate Loader Kit to raise Nikon Ti E to correct level when using PLW20 Well Plate Loader ProScan Controller with three stepper drives for filters, shutters or a focus drive ProScan Controller with X Y Z drives and encoder capability ProScan controller with XYZ drives, three filter wheel drives, three shutter drives and encoder capability ProScan controller with XYZ drives for linear stage control ProScan controller with XYZ drives, three filter wheel drives, and three shutter drives for linear stage control Incubation chamber for NZ100/200 Incubation chamber for NZ400 Incubation chamber for H117 stages Notes Depending on the exact variant of Ti/Ti2, some Prior parts may not be compatible. Please contact Prior before ordering with the exact variant of microscope. 10
12 Nikon Ni Focussing Stage Sample holders - H224LP - H234LP Motorised stages 3 - H101E50/E80 (dependent on substage) - HIP4E50/E80 (dependent on substage) - HEP4E50/E80 (dependent on substage) - PL101E50/E80 (dependent on substage) - PLE01E50/E80 (dependent on substage) Slide Loader - PL PL238 2 OR PL PL304 - PL310 Sample holder adapter H3848 Flat top Motorised stages 3 - H101E1CI/NI (dependent on substage) - H101P1CI/NI (dependent on substage) - H101P2CI/NI (dependent on substage) -H101E2CI/NI (dependent on substage) Sample holders (Flat top) - H224F - H234F 8 Slide Stage 3 - H138E50/E80 (dependent on substage) - HE38E50/E80 (dependent on substage) NanoScanZ 4 - NZ200F Sample holders (H138A) - H238LP - H238PLP - H Nikon Automation Guide
13 Nikon Ni Focussing Stage Lumen L220SNI - L200SNI Filter wheels - HF108A/HF220 (Excitation) - HF110A/HF220 (Excitation) Lumen L100###NI (Replace ### with wavelength) Brightfield - LDB103NI - LDB102NI Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF Lumen L220NI - L200NI Shutters - HF200HT (Excitation) - HF201HT (Excitation) Joystick Control Unit - PS3J100 Focus Motor - PS3H122R + H122KON + H NIKRFK + NIKNIMA 12
14 Nikon Ni Focussing Stage Product ES10ZE H101E50/E80 H101E1CI/NI H101P1CI/NI H101P2CI/NI H101E2CI/NI H1P4E50/E80 H138E50/E80 HE38E50/E80 H224F H224LP H234F H234LP H122KON H234F H238LP H238PLP H239 H3848 H3940 HEP4E50/E80 HF108A/HF220 HF110A/HF220 L100###NI L200NI L200SNI L220NI L220SNI Details Focus only controller H101A stage with 2mm screw pitch and 200 step motor H101F flat top stage with 1 mm screw pitch, 200 step motors and encoders H101F flat top stage with 1mm screw pitch and 200 step motors. H101F flat top stage with 2mm screw pitch and 200 step motors. H101F flat top stage with 2 mm screw pitch, 200 step motors and encoders H101A stage with 1 mm screw pitch and 400 step motor H138A Eight slide holding stage with 200 step motor and 2mm ball screw H138A Eight slide holding stage with 200 step motor and 2mm ball screw and encoders Low profile slide holder for flat top stages Low profile slide holder Low profile slide holder for flat top stages for four 76 x 26 mm slides Low profile slide holder, for four 76 x 26 mm slides Direct fine focus coupling kit for Nikon and Olympus Low profile slide holder (4 slides) for flat top stages Low profile slide holder for eight 76 x 26 mm slides Semi recessed low profile slide holder for eight 76 x 26 mm slides Aluminium plate for H138A and HE38 Adapter allowing conventional sample holders to be fitted to flat top stages Adapter for PS3H122R (Nikon Ni-U and Ni-C only) H101A stage with 1mm screw pitch, 400 step motor and encoders 8 position 32 mm filter wheel with adapter 10 position 25 mm filter wheel with adapter Single LED illumination system. Replace ### with wavelength required. Metal Halide Illumination Source Metal Halide Illumination Source with integral shutter. Metal Halide Illumination Source with extended UV/IR wavelengths Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengths 13 Nikon Automation Guide
15 Nikon Ni Focussing Stage Product Details LDB102NI Brightfield Illumination LED for Nikon (standalone) LDB103NI Brightfield Illumination LED for Nikon (ProScan control) PS3H122R Generic Focus Drive with rotating cable system to prevent twisting NIKNIMA Adapter for Nikon Ni for NIKRFK NIKRFK Nikon remote focussing kit - includes controller, cables and focus motor NZ200F NanoScanZ (adapted for flat top stages) PL200 Slide Loader PL228 Bevel edged sample holder for 1 x 3 slides. Includes 4 slide racks for for 1 x 3 slides PL238 Bevel edged sample holder for 2 x3 slides. Includes 2 slide racks for 2 x 3 slides. PL304 Barcode reader for PL200 PL310 Elevated baseplate to improve clearance PLE01E50/E80 Encoded H101A stage for use with Slide Loader (use with PL228 only) PL101E50/E80 H101A stage for use with slide loader PS3H122R Generic focus drive with rotating cable system to prevent twisting PS3J100 Multifunctional manual joystick for ProScan V31F ProScan controller with three stepper drives for focus and two filter wheels or 3 shutters V31XYZE ProScan controller with XYZ drives and encoder input V31XYZEF ProScan controller with XYZ drives, three filter wheel drives, shutter drives and encoder input Notes 1The slide loader can only be used with the PL101E50/E80 or PLE01E50/80 stages 2 The PLE01E50/80 is only for use with the PL228 3 The suffix E50 OR CI is applicable for Ni microscopes with a SS Sub-stage. For SSR sub-stages add E80 or NI instead 4 NZ200F can only be used with flat top stages 14
16 Nikon Ni Focussing Nosepiece Sample holders - H224LP - H224PLP - H234LP Slide Loader - PL200 - PL238 OR PL228 - PL304 - PL310 Post Sample Holder - HZP HZP HZP1020 HZP Post Mounts - HZP150 - HZP200 - HZP250 - HZP300 Motorised stages - H101NFN - HIP4NFN - HEP4NFN - PL101NFN - PLE01NFN Z-Deck - ZDN 12MP - ZDN12ME - ZDN12MK - ZDN12MF Z-Deck Sample Holders - HZ202 - HZ203 NanoScanZ* - NZ200F (HZ201 adapter 15 Nikon Automation Guide
17 Nikon Ni Focussing Nosepiece Lumen L220SNI - L200SNI Translation Stage - ZDP50T - ZDP50K Lumen L100###NI (Replace ### with wavelength) Filter wheels - HF108A/HF220 (Excitation) - HF110A/HF220 (Excitation) Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF Shutters - HF200HT (Excitation) - HF201HT (Excitation) Brightfield - LDB103NI - LDB102NI Lumen L220NI - L200NI Joystick Control Unit - PS3J
18 Nikon Ni Focussing Nosepiece Product ES10ZE H101NFN H1P4NFN H224F H234F H224LP H224PLP H234LP HEP4NFN HF108A/HF220 HF110A/HF220 HF200HT HF201HT HZ201 HZ202 HZ203 HZP150 HZP200 HZP250 HZP300 HZP1000 HZP1010 HZP1020 L100###NI L200NI L200SNI L220NI L220SNI LDB102NI LDB103NI NZ200F Details Focus only controller H101A stage with 2mm screw pitch and 200 step motor H101A stage with 1 mm screw pitch and 400 step motor Low profile slide holder for flat top stages Low profile slide holder for flat top stages for four 76 x 26 mm slides Low profile slide holder Low profile slide holder (71 x 51 mm slide holder) Low profile slide holder for 4 71 x 21 mm slides H101A stage with 1mm screw pitch, 400 step motor and encoders 8 position 32 mm filter wheel with adapter 10 position 25 mm filter wheel with adapter High speed shutter with 25 mm aperture High speed shutter with 32 mm aperture Adapter allowing upright sample holders to be inserted into Z-Deck Solid Insert Plate for Z-Deck 108 mm ring insert plate for Z-Deck Rigid post mount 150 mm tall Rigid post mount 200 mm tall Rigid post mount 250 mm tall Rigid post mount 300 mm tall Manipulator holder for HZP150/200/250/300 Standard sample holder for HZP150/200/250/300 Circular holder for HZP150/200/250/300 Single LED illumination system. Replace ### with wavelength required Metal Halide Illumination Source Metal Halide Illumination Source with integral shutter Metal Halide Illumination Source with extended UV/IR wavelengths Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengths Brightfield Illumination LED for Nikon (standalone) Brightfield Illumination LED for Nikon (ProScan control) NanoScanZ (adapted for flat top stages) 17 Nikon Automation Guide
19 Nikon Ni Focussing Nosepiece Product Details NZ200F NanoScanZ (adapted for flat top stages) PL200 Slide Loader PL228 Bevel edged sample holder for 1 x 3 slides. Includes 4 slide racks for for 1 x 3 slides PL238 Bevel edged sample holder for 2 x3 slides. Includes 2 slide racks for 2 x 3 slides PL310 Elevated baseplate to improve clearance PL304 Barcode reader for PL200 PL101NFN H101A stage for use with slide loader PLE01NFN Encoded H101A stage for use with Slide Loader (use with PL228 only) PS3J100 Multifunctional manual joystick for ProScan V31F ProScan controller with three stepper drives for focus and two filter wheels or 3 shutters V31XYZE ProScan controller with XYZ drives and encoder input V31XYZEF ProScan controller with XYZ drives, three filter wheel drives, shutter drives and encoder input ZDN12MP Motorised Z-Deck quick adjust platform system ZDN12ME Motorised Z-Deck quick adjust platform system (Encoded) ZDN12MK Manual Z-Deck quick adjust platform system ZDN12MF Fixed plate Z-Deck quick adjust platform system ZDP50K Translation stage for microscope (manual) ZDP50T Translation stage for microscope (motorised) Notes 1) The slide loader can only be used with the PL101FN or PLE01FN stages 2) The PLE01FN is only for use with the PL228 3) The NZ200F can only be used with the Z-Deck 18
20 Nikon AZ100 Motorised stages 3 - H101AZEP/E50 - HIP4AZEP/E50 - HEP4AZEP/E50 - PL101AZEP/E50 - PLE01AZEP/E50 Sample holders - H224LP - H473UP Sample holder adapter Flat top Motorised stages 3 - H101E1AZEP - H101P1AZEP - H101P2AZEP Sample holders (Flat top) - H224F - H234F 8 Slide Stage 3 - H138AZEP/E50 - HE38AZEP/E50 NanoScanZ 4 - NZ200F Sample holders (H138A) - H238LP - H238PLP - H Nikon Automation Guide
21 Slide Loader - PL PL238 2 OR PL PL304 Lumen L220S - L200S - L220 - L200 Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF Focus Motor - PS3H122S15 Joystick Control Unit - PS3J100 Focus Motor - PS3H122R + H
22 Nikon AZ100 Product ES10ZE H101ZEP/E50 H101E1AZEP H101P1AZEP H101P2AZEP H101E2AZEP H1P4ZEP/E50 H138ZEP/E50 HE38ZEP/E50 HEP4ZEP/E50 H224F H224LP H234F H238LP H238PLP H239 H2531 H3848 H473UP L200 L200S L220 L220S NZ200F Details Focus only controller H101A stage with 2mm screw pitch and 200 step motor H101F flat top stage with 1 mm screw pitch, 200 step motors and encoders H101F flat top stage with 1mm screw pitch and 400 step motors H101F flat top stage with 2mm screw pitch and 200 step motors H101F flat top stage with 2 mm screw pitch and 200 step motors and encoders H101A stage with 1 mm screw pitch and 400 step motor H138A Eight slide holding stage with 200 step motor and 2mm ball screw H138A Eight slide holding stage with 200 step motor and 2mm ball screw and encoders H101A stage with 1mm screw pitch, 400 step motor and encoders Low profile slide holder for flat top stages Low profile slide holder Low profile slide holder (4 slides) for flat top stages Low profile slide holder for eight 76 x 26 mm slides Semi recessed low profile slide holder for eight 76 x 26 mm slides Aluminium plate for H138A and HE38 Adapter for PS3H122R to fit to AZ100 Adapter allowing conventional sample holders to be fitted to flat top stages Universal sample holder Metal Halide Illumination Source Metal Halide Illumination Source with integral shutter Metal Halide Illumination Source with extended UV/IR wavelengths Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengths NanoScanZ (adapted for flat top stage) 21 Nikon Automation Guide
23 Product Details PL200 Slide Loader PL228 Bevel edged sample holder for 1 x 3 slides. Includes 4 slide racks for for 1 x 3 slides PL238 Bevel edged sample holder for 2 x3 slides. Includes 2 slide racks for 2 x 3 slides PL304 Barcode reader for PL200 PL101ZEP/E50 H101A stage for use with slide loader PLE01ZEP/E50 Encoded H101A stage for use with Slide Loader (use with PL228 only) PS3H122R Generic focus drive with rotating cable system to prevent twisting PS3H122RS15 Focus motor adapted for AZ100 PS3J100 Multifunctional manual joystick for ProScan V31F ProScan controller with three stepper drives for focus and two filter wheels or 3 shutters V31XYZE ProScan controller with XYZ drives and encoder input V31XYZEF ProScan controller with XYZ drives, three filter wheel drives, shutter drives and encoder input Notes 1 The slide loader can only be used with the PL101ZEP/E50 or PLE01ZEP/E50 stages 2 The PLE01ZEP/E50 is only for use with the PL228 3 AZEP is for Episcopic AZ100s, E50 for diascopic 4 NZ200F can only be used with flat top stages Note that the AZ100 only accepts liquid light guides so remove adaptors and collimators from illumination devices 22
24 Nikon SMZ18/25 Sample holders - H224LP - H473UP OptiScan Stage 1 - ES111 Sample holders (Flat top) - H224F - H234F Sample holder adapter -H3848 Flat top Motorised stages - H101P2F - H101E2F Adapter -HSMZ1825 NanoScanZ - NZ200F 23 Nikon Automation Guide Laser Autofocus - LF210 - LF100K - LF320
25 Focus Motor - PS3H122S15 Lumen L220S - L200S - L220 - L200 Controllers* - ES10ZE - ES V31XYZE - V31F - V31XYZEF *Compatible with most imaging software Joystick Control Unit - PS3J100 - CS1525DP 24
26 Nikon SMZ18/25 Product Details CS152DP OptiScan III Joystick ES10ZE Focus only controller ES11 OptiScan III Controller ES111 ES11 stage with 125 x 75 mm travel H101P2F H101F flat top stage with 2mm screw pitch and 200 step motors H101E2F H101F flat top stage with 2mm screw pitch and 200 step motors with encoders H224F Low profile slide holder for flat top stages H224LP Low profile slide holder H234F Low profile slide holder (4 slides) for flat top stages H3848 Adapter allowing conventional sample holders to be fitted to flat top stages H473UP Universal sample holder HSMZ1825 Adapter for mounting stages on the SMZ1825 L200 Metal Halide Illumination Source L200S Metal Halide Illumination Source with integral shutter L220 Metal Halide Illumination Source with extended UV/IR wavelengths L220S Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengths LF100K LF210 Digipot and Keypad LF210 Laser AutoFocus (requires flange and keypad) LF320 LF210 Mounting flange for Nikon Microscopes NZ200F NanoScanZ (adapted for flat top stage) PS3H122S15 Focus motor adapted for SMZ 18 (not suitable for SMZ 25) PS3J100 Multifunctional manual joystick for ProScan V31F ProScan controller with three stepper drives for focus and two filter wheels or 3 shutters V31XYZE ProScan controller with XYZ drives and encoder input V31XYZEF ProScan controller with XYZ drives, three filter wheel drives, shutter drives and encoder input Notes 1 The ES111 stage can ONLY be controlled by the ES11 controller. Consult Prior Scientific for the difference between OptiScan and ProScan control systems and stages 25 Nikon Automation Guide
27 Nikon SM800/1000/1270/1500 SMZ 800/1000/1270/1500 Stage Addition Older SMZ Microscopes can be enhanced with Prior equipment, mostly in a similar way to the SMZ18/25. The optimal stage configuration will depend on the illumination base on the stereo microscope. This guide only applies for the SMZ 800, SMZ 1000, SMZ1270 and SMZ 1500 stereo microscopes from Nikon. For the grey cells, the correct configuration is the addition of E600 to the stage. Stage Stage description Adapter to be used Light Base Light Base Description P2-PB Plain base P2-DBL LED Diascopic illumination base H101P2F Flat top, 200 step, 2 mm ballscrew HSMZ1825 P2-DBF Fiber Diascopic illumination base HE01E2F Encoded flat top, 200 step, 2 mm ballscrew P-PS32 Plain stand P-DSL32 LED Diascopic illumination stand P-DSF32 Fiber Diascopic illumination stand C-DS Diascopic stand S H101P2FE600 Flat top, 200 step, 2 mm ballscrew C-PS160 Plain stand H101E2FE600 Encoded flat top, 200 step, 2 mm ballscrew C-DSD115 DIA stand H101E step, 2 mm ballscrew H448 C-DSD230 DIA stand H1P4E step, 1 mm ballscrew C-DSDF DIA stand F HEP4E600 Encoded 400 step, 1 mm ballscrew C-DSS115 DIA stand C-DSS230 DIA stand 26
28 Nikon LV100/150 Sample holders - H220 - H234LP - H224LP - HWC15SNL (H105) - HWC15VNL (H105) - H231 (H105) - H227 (H105) Motorised stages - H101NLV - HIP4NLV - HEP4NLV - H105N2F Flat top Motorised stages - H101P2NLV - H101E1NLV - H101P1NLV Sample holder adapter H3848 NanoScanZ 1 - NZ200F 8 Slide Stage - H138NLV - HE38NLV Sample holders (Flat top) - H220F - H230F - H224F - H234F Sample holders (H138A) - H238LP - H238PLP - H Nikon Automation Guide
29 Brightfield - LDB103NI - LDB102NI Laser Autofocus - LF210 - LF100K - LF320 Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF Compatible with most imaging software Focus Motor - PS3H122R/H3909 Joystick Control Unit - PS3J
30 Nikon LV100/150 Product Details ES10ZE Focus only controller H101E1NLV H101F flat top stage with 1 mm screw pitch, 200 step motors and encoders H101NLV H101A stage with 2mm screw pitch and 200 step motor H101P2NLV H101F flat top stage with 2mm screw pitch and 200 step motors H105N2F Large format stage with 154 x 154 mm travel range, 200 step motors and 2 mm screw pitch H101P1NLV H101F flat top stage with 1mm screw pitch and 400 step motors. H1P4NLV H101A stage with 1 mm screw pitch and 400 step motor H138NLV H138A Eight slide holding stage with 200 step motor and 2mm ball screw HE38NLV H138A Eight slide holding stage with 200 step motor and 2mm ball screw and encoders H220 Glass insert plate H220F H101F glass insert plate H224F Low profile slide holder for flat top stages H224LP Low profile slide holder (76 x 26 mm slide) H227 Glass plate (H105 stages) - not suitable for transmitted microscopy H230 Aluminium insert plate H230F H101F aluminium insert plate H231 Aluminium plate (H105 stages) H234F Low profile slide holder (4 slides) for flat top stages H224LP Low profile slide holder (4 x 26 x 76 mm slides) H238LP Low profile slide holder for eight 76 x 26 mm slides H238PLP Semi recessed low profile slide holder for eight 76 x 26 mm slides H239 Aluminium plate for H138A and HE38 H3848 Adapter allowing conventional sample holders to be fitted to flat top stages H3909 Focus Motor Adapter for Nikon LV series and L200 HE05NL/2 Encoded variant of H105/2 HEP4NLV H101A stage with 1mm screw pitch, 400 step motor and encoders HWC15SNL Wafer chuck for 100 and 150 mm wafers (H105 stages) HWC15VNL Wafer chuck, rotatable with vacuum for 150 mm (H105 stages) LDB102NI Brightfield Illumination LED for Nikon (standalone) LDB103NI Brightfield Illumination LED for Nikon (ProScan control) LF100K LF210 Digipot and Keypad LF210 Laser AutoFocus (requires flange and keypad) LF320 LF210 Mounting flange for Nikon Microscopes NZ200F NanoScanZ (adapted for flat top stages) 29 Nikon Automation Guide
31 Product Details PS3H122R Generic Focus Drive with rotating cable system to prevent twisting PS3J100 Multifunctional manual joystick for ProScan V31F ProScan controller with three stepper drives for focus and two filter wheels or 3 shutters V31XYZE ProScan controller with XYZ drives and encoder input V31XYZEF ProScan controller with XYZ drives, three filter wheel drives, shutter drives and encoder input Notes 1 NZ200F can only be used with flat top stages 30
32 Nikon L200/300 Large format motorised stages 1 - H116/2-8 - HE16/2-8 - H105N2F Sample holders for large format stages - H225 (H116) - H232 (H116) - HWC20S (H116) - HWC20V (H116) - HWC15SNL (H105) - HWC15VNL (H105) - H231 (H105) - H227 (H105) Large format motorised stages 1 - H112/2ST - HE12/2ST L300 ONLY Sample holders for large format stages - H223 (H112) - H223 (H112) - H223B (H112) - HWC30V (H112) 31 Nikon Automation Guide
33 Brightfield - LDB103NI - LDB102NI Laser Autofocus - LF210 - LF100K - LF320 Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF Compatible with most imaging software Focus Motor - PS3H122R/H3909 Joystick Control Unit - PS3J
34 Nikon L200/300 Product Details ES10ZE Focus only controller H112/2ST Stage with 300 x 300 mm travel range and 2 mm ball screw HE12/2ST As above with encoders H116/2-8 Large format stage with 255 x 215 mm travel range, 200 stepper motor and 2 mm screw pitch HE16/2-8 As above with encoders H105N2F Large format stage with 154 x 154 mm travel range, 200 step motors and 2 mm screw pitch H221 Glass Plate (H112 stages) - not suitable for transmitted microscopy H225 Glass plate (H116 stages) - not suitable for transmitted microscopy H227 Glass plate (H105 stages) - not suitable for transmitted microscopy H231 Aluminium plate (H105 stages) H233 Aluminium plate (H112 stages) H233B Aluminium plate with M4 and M6 tapped holes (H112 stages) H232 Aluminium plate (H116 stages) H3909 Focus Motor Adapter for Nikon LV series and L200 HWC15SNL Wafer chuck for 100 and 150 mm wafers (H105 stages) HWC15VNL Wafer chuck, rotatable with vacuum for 150 mm (H105 stages) HWC20S Wafer chuck for for 150 mm and 200 mm wafers (H116 stages) HWC20V Wafer chuck, rotatable with vacuum for 200 mm wafers (H116 stages) HWC30S Wafer chuck, rotatable, for 300 mm wafers (H112 stages) LDB102NI Brightfield Illumination LED for Nikon (standalone) LDB103NI Brightfield Illumination LED for Nikon (ProScan control) LF100K LF210 Digipot and Keypad LF210 Laser AutoFocus (requires flange and keypad) LF320 LF210 Mounting flange for Nikon Microscopes PS3H122R Generic Focus Drive with rotating cable system to prevent twisting PS3J100 Multifunctional manual joystick for ProScan V31F ProScan controller with three stepper drives for focus and two filter wheels or 3 shutters V31XYZE ProScan controller with XYZ drives and encoder input V31XYZEF ProScan controller with XYZ drives, three filter wheel drives, shutter drives and encoder input Notes 1 Only the L300 can accommodate H112 stages 33 Nikon Automation Guide
35 NOTES 34
36 Nikon TS2R NanoScanZ Incubation Chambers - W3569 (NZ10/2000) - W3719 (NZ400) NanoScanZ Sample holders - H499XR (NZ100/200) - H472XR (NZ100/200) - H471XR (NZ100/200) - NZ303 (NZ400) - NZ302 (NZ400) - NZ301 (NZ400) Motorised stages - H117P1N4 - H117E1N4 Option to add H117ACCM Sample holders - H473XR - H223XRNC - H229XR -H224XRLP Linear stages - HLD117NN (HLD324 adapter required for use of Prior Sample Holders) H139 Stages - H139P1N4 - H139E1N4 H139 Sample holders - H171XR - H223XR2 - H473R3 35 Nikon Automation Guide
37 Nikon TS2R NanoScan Z stages - NZ400 Lumen 200* - L220S - L200S - L220 - L200 Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF - VLD31XYZ - VLD31XYZEF Joystick Control Unit - PS3J100 Focus Motor - PS3H122R + H2975 / H122KON 36
38 Nikon TS2R Product ES10ZE H117ACCM H117E1N4 H117P1N4 H122KON H139P1N4 H139E1N4 H171XR H223XRNC H223XR2 H224XRLP H229XR H473XR H473XR3 HLD117NN HLD324 L200 L200S L220 L220S NZ301 NZ302 NZ303 NZ400 PS3H122R/H2975 PS3J100 V31F V31XYZE V31XYZEF VLD31XYZ VLD31XYZF W3569 W3719 Details Focus only system controller Extension plates for H117 stages H117 motorised stage with 1mm screw pitch and encoders H117 motorised stage with 1mm screw pitch Direct fine focussing kit for Nikon and Olympus Microscopes H139 motorised stage with 1 mm ballscrew, 400 stepper motor H139 motorised stage with 1 mm ballscrew, 400 stepper motor and 100 nm encoder 9 slide holder for H139 Extra recessed low profile microtitre plate for H117 stages 2 micro titre plate holder for H139 Extra recessed low profile slide holder for H117 stages Extra recessed petri dish holder for H117 stages Extra recessed universal holder for H117 stages Double Universal sample holder for H139 Linear motor stage with travel range of 81 x 121 mm and 50 nm encoders Required to adapt linear stages for Prior insert Metal Halide Illumination Source Metal Halide Illumination Source with integral shutter Metal Halide Illumination Source with extended UV/IR wavelengths Metal Halide Illumination Source with integral shutter and with extended UV/IR wavelengths Extra recessed well plate holder for NZ400 Extra recessed slide/petri dish holder for NZ400 Extra recessed slide holder for NZ400 Nanopositioning piezo Z stage with 400 um of travel and controller Focus drive and adapter Multifunctional interactive control centre for ProScan ProScan Controller with three stepper drives for filters, shutters or a focus drive ProScan Controller with X Y Z drives and encoder capability ProScan controller with XYZ drives, three filter wheel drives, three shutter drives and encoder capability ProScan controller with XYZ drives for linear stage control ProScan controller with XYZ drives, three filter wheel drives, and three shutter drives for linear stage control Incubation chamber for NZ100/200 Incubation chamber for NZ Nikon Automation Guide
39 NOTES 38
40 Ci Sample holders - H224LP - H234LP 8 Slide Stage - H138E50 - HE38E50 Motorised stages - H101E50 - HIP4E50 - HEP4E50 Sample holder adapter H3848 Flat top Motorised stages - H101E1CI - H101P1CI - H101P2CI - H101E2CI Sample holders (Flat top) - H224F - H234F 39 Nikon Automation Guide
41 Ci Sample holders (H138A) - H238LP - H238PLP - H239 Filter wheels - HF108A/HF220 (Excitation) - HF110A/HF220 (Excitation) Lumen L220SNI - L200SNI Brightfield - LDB103NI - LDB102NI Shutters - HF200HT/HF220 (Excitation) - HF201HT/HF220 (Excitation) Lumen L100###NI (Replace ### with wavelength) Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF Lumen L220NI - L200NI Focus Motor - PS3H122R + H122KON + H3940 Joystick Control Unit - PS3J
42 Ci Product Details ES10ZE H101E50 H101E1CI H101P1CI H101P2CI H101E2CL H1P4E50 H138E50 HE38E50 H224F H224LP H234F H234LP H122KON H234F H238LP H238PLP H239 H3848 H3940 HEP4E50 HF108A/HF220 HF110A/HF220 HF200HT/HF220 HF201HT/HF220 L100###NI L200NI L200SNI L220NI L220SNI LDB102NI LDB103NI PS3H122R NZ200F PS3H122R Focus only controller H101A stage with 2mm screw pitch and 200 step motor H101F flat top stage with 1 mm screw pitch, 200 step motors and encoders H101F flat top stage with 1mm screw pitch and 400 step motors H101F flat top stage with 2mm screw pitch and 200 step motors H101F flat top stage with 2 mm screw pitch and 200 step motors H101A stage with 1 mm screw pitch and 400 step motor H138A Eight slide holding stage with 200 step motor and 2mm ball screw H138A Eight slide holding stage with 200 step motor and 2mm ball screw and encoders Low profile slide holder for flat top stages Low profile slide holder Low profile slide holder for flat top stages extra recessed, for four 76 x 26 mm slides Low profile slide holder, extra recessed, for four 76 x 26 mm slides Direct fine focus coupling kit for Nikon and Olympus Low profile slide holder (4 slides) for flat top stages Low profile slide holder for eight 76 x 26 mm slides Semi recessed low profile slide holder for eight 76 x 26 mm slides Aluminium plate for H138A and HE38 Adapter allowing conventional sample holders to be fitted to flat top stages Adapter for PS3H122R H101A stage with 1mm screw pitch, 400 step motor and encoders 8 position 32 mm filter wheel with adapter 10 position 25 mm filter wheel with adapter High Speed Shutter 25 mm aperture for use with filter wheel with adapter High Speed Shutter 32 mm aperture for use with filter wheel with adapter Single LED illumination system. Replace ### with wavelength required. Metal Halide Illumination Source Metal Halide Illumination Source with integral shutter Metal Halide Illumination Source with extended UV/IR wavelengths Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengths Brightfield Illumination LED for Nikon (standalone) Brightfield Illumination LED for Nikon (ProScan control) Generic Focus Drive with rotating cable system to prevent twisting NanoScanZ (adapted for flat top stages) Generic focus drive with rotating cable system to prevent twisting 41 Nikon Automation Guide
43 Ci Product Details PS3J100 Multifunctional manual joystick for ProScan V31F ProScan controller with three stepper drives for focus and two filter wheels or 3 shutters V31XYZE ProScan controller with XYZ drives and encoder input V31XYZEF ProScan controller with XYZ drives, three filter wheel drives, shutter drives and encoder input 42
44 Nikon MA100 Sample Holders - H224ROTS - H473 - H649 - H656 - H659 OptiScan stage - ES107NTS Brightfield - LDB102NI Focus Motor - PS3H122R/H3550 Controllers - ES10ZE - ES11 - CS515DP 43 Nikon Automation Guide
45 Product Details CS52DP OptiScan III Joystick ES10ZE Focus only controller ES107NTS OptiScan motorised stage 125 x 75 mm ES11 OptiScan III Controller H224ROTS Recessed rotating holder for one 26 x 76 mm slide H473 Universal Specimen Holder for slides and petri dishes H649 Holder for a single 1, 1.25 and 1 metallurgical slide specimen H656 Holder for a single metallurgical specimen, 1.25 diameter H659 Holder for one mounted metallurgical specimen, 15 diameter with 1,2,4 or 8 chambers. LDB102NI Brightfield Illumination LED for Nikon (stand alone) PS3H122R/H3550 Focus motor and adapter 44
46 MA200 Brightfield - LDB102NI - LDB103NI C-HGFI/C-HGFIE required Lumen L200S - L220S - L200 - L220 Note that the collimator must be removed 45 Nikon Automation Guide Focus Motor - PS3H122R + H3273
47 NanoScanZ Sample holders - NZ303 (NZ400) - NZ302 (NZ400) - NZ301 (NZ400) NanoScan Z stages - NZ400 Motorised stages - H117N2M4 - H117N1M4 Joystick Control Unit - PS3J100 Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF Sample holders - H473XR - H234XR - H224XRLP - H649 - H656 - H657 - H658 - H
48 Nikon MA200 Product Details ES10ZE Focus only system controller H117P1M4 H117 motorised stage with 1mm screw pitch H234XRLP Low profile slide holder, extra recessed, for one 76 x 51 mm slide H234 Low profiles slide holder, extra recessed, for four 76 x 26 mm slides H649 Holder for 1, 1.25 and 1.5 mounted metallurgical specimens H656 Holder for 1.25 mounted metallurgical specimens H657 Holder for 1 2 mounted metallurgical specimen H658 Holder for 6 mounted metallurgical specimens 1.25 diameter H659 Holder for one mounted metallurgical specimen, 1.5 in diameter with or 8 chambers L200 Metal Halide Illumination Source L200S Metal Halide Illumination Source with integral shutter L220 Metal Halide Illumination Source with extended UV/IR wavelengths L220S Metal Halide Illumination Source with integral shutter and with extended UV/IR wavelengths L300DLG 3 LED illumination system for with single band filter set with UV/Violet peak at 365 nm and light guide LDB102NI Brightfield Illumination LED for Nikon (standalone) LDB103NI Brightfield Illumination LED for Nikon (ProScan control) NZ301 Extra recessed well plate holder for NZ400 NZ302 Extra recessed slide/petri dish holder for NZ400 NZ303 Extra recessed slide holder for NZ400 NZ400 Nanopositioning piezo Z stage with 400 um of travel and controller PS3H122R/H3273 Focus drive and adapter PS3J100 Multifunctional manual joystick for ProScan V31F ProScan Controller with three stepper drives for filters, shutters or a focus drive V31XYZE ProScan Controller with X Y Z drives and encoder capability V31XYZEF ProScan controller with XYZ drives, three filter wheel drives, three shutter drives and encoder capability 47 Nikon Automation Guide
49 NOTES 48
50 ProZ stand for Nikon Lumen L220NI - L200NI - L220SNI - L200SNI Brightfield - LDB103NI - LDB10FNI Adapter for LV series - ZCALV Pillar Mounting Adapter ZC12FLNG Joystick Control Units - PS3J100 ProZ Stand - ZC12 - ZC12EL - ZC12FL Controllers - ES10ZE - V31XYZE - V31F - V31XYZEF Compatible with most imaging software Sample holders - H224LP (H101 stages ) - H473UP (H101 stages ) - H230 (H101 stages) - H220 (H101 stages) - H227 (H105 stages) - H231 (H105 stages) - H225 (H116 stages) - H232 (H116 stages) - H233 (H112 stages) - H221 (H112 stages) 49 Nikon Automation Guide
51 ProZ stand for Nikon Adapter for AZ100 - ZCAAZ - ZCAAZS (ZC12EL only) Adapter for SMZ18/25 - ZCASMZ25 - ZZCASMZ25S (ZC12EL only) Mounting stand - H414 (for use with ZC12EL) -H413 Clamping Arms ZCBCK Stage mount ZCBRL ZCBTL Large Format Motorised stages - H116/2 - HE16/2 - H112/2ST - HE12/2ST Focus Blocks - FB201 - FB203 - FB204/4 - FB205/E - FB206/E Motorised stages - H101 - HIP4 - HEP4 - H105N2F 50
52 ProZ stand for Nikon Product Details ES10ZE Focus only controller FB201 Manual focussing block FB203 Motorised Linear Axis FB204 Motorised focus holding an incident light Prior stage; with flanges for fitting to optical table FB204E As above with Encoders FB205 Motorised focus with offset base holding an incident light Prior stage with flanges for fitting to optical table FB205E As above with encoders FB206 Motorised focus holding a transmitted light Prior stage with flanges for fitting to optical table FB206E As above with encoders H101 H101A stage with 2mm screw pitch and 200 step motor H105N2F Large format stage with 154 x 154 mm travel range, 200 step motors and 2 mm screw pitch H112/2ST Large format stage with 302 x 302 mm travel range, 200 stepper motor and 2 mm screw pitch H116/2 Large format stage with 255 x 215 mm travel range, 200 stepper motor and 2 mm screw pitch H1P4 H101A stage with 1 mm screw pitch and 400 step motor H220 Glass plate (H101 stages) - not suitable for transmitted microscopy H221 Glass plate (H112 stages) - not suitable for transmitted microscopy H224LP Low profile slide holder (H101 stages) H225 Glass plate (H116 stages) - not suitable for transmitted microscopy H227 Glass plate (H105 stages) - not suitable for transmitted microscopy H230 Aluminium plate (H101 stages) H231 Aluminium plate (H105 stages) H232 Aluminium plate (H116 stages) H233 Aluminium plate (H112 stages) H413 Mounting stand for H101 or H105 stages H414 Mounting stand for H112 or H116 stages H473UP Universal sample holder (H101 stages) HE12/2ST Encoded variant of H112/2ST HE16/2 Encoded variant of H116/2 HEP4 H101A stage with 1mm screw pitch, 400 step motor and encoders 51 Nikon Automation Guide
53 ProZ stand for Nikon Product Details L200NI Metal Halide Illumination Source L200SNI Metal Halide Illumination Source with integral shutter. L220NI Metal Halide Illumination Source with extended UV/IR wavelengths L220SNI Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengths LDB102NI Brightfield Illumination LED for Nikon (standalone) LDB103NI Brightfield Illumination LED for Nikon (ProScan control) PS3J100 Multifunctional manual joystick for ProScan V31F ProScan controller with three stepper drives for focus and two filter wheels or 3 shutters V31XYZE ProScan controller with XYZ drives and encoder input V31XYZEF ProScan controller with XYZ drives, three filter wheel drives, shutter drives and encoder input ZC12 Motorised Z column with 500 mm 2 base and 250 mm of travel ZC12EL Motorised Z column with approx 600 x 750 mm base and 250 mm of travel ZC12FL Motorised Z column with no base and 250 mm of travel ZC12FLNG Adapter for mounting ZC12FL to optical mounting table ZCAAZ Nikon AZ100 Optical Mounting Arm ZCAAZS Extended AZ100 Optical Mounting Arm (ZC12EL only) ZCALV Nikon LV Optical Mounting Arm ZCASMZ25 Nikon SMZ18/25 Optical Mounting Arm ZCASNZ25S Extended SMZ1/25 Optical Mounting Arm (ZC12EL only) ZCBCK Universal clamping kit for illumination bases ZCBRL H101, H105 stage mount reflected light only. Add HP1770 for manual stage dovetail option. ZCBTL Prior H101, H105 stage mount transmitted light. Accepts 50mm diffuser/filter. Includes Prior LDB101 LED light source Notes Note that H116 and H112 stages require ZC12EL and H
54 Stage Codes for Nikon H101F FLAT TOP STAGE FOR UPRIGHT MICROSCOPES H101P2F This indicates whether the stage is encoded or not: P: Not currently encoded (upgrade available) E: Encoded This indicates the microscope type the stage is suitable for: F: SMZ18/25 (requires HSMZ1825 adaptor) NI: Nikon (SSR substage) CI: Nikon (SS substage) ZEP: Nikon (AZ100) This indicates the ballscrew of the stage: 1: 1 mm ballscrew 2: 2 mm ballscrew H117 STAGE FOR INVERTED MICROSCOPES This indicates the microscope type the stage fits to and stepper motor the stage has: H117E1#4 This indicates the ballscrew of the stage: NN: Nikon, 200 stepper motor N4: Nikon, 400 stepper motor MA: Nikon, 200 stepper motor (MA200 only) M4: Nikon, 400 stepper motor (MA200 only) 1: 1 mm ballscrew 2: 2 mm ballscrew This indicates whether the stage is encoded or not: H101A STAGE FOR UPRIGHT MICROSCOPES H101A This indicates the ballscrew of the stage; 0: 2 mm ballscrew P: 1 mm ballscrew 53 Nikon Automation Guide P: Not currently encoded (upgrade available) E: Encoded This indicates the stepper motor of the stage: 1: 200 stepper motor 4: 400 stepper motor H138A STAGE FOR UPRIGHT MICROSCOPES H138A This indicates whether the stage is encoded or not: 1: Not currently encoded (upgrade available) E: Encoded This indicates the microscope type the stage fits to; E50: Nikon (SS substage) E80: Nikon (SSR substage) AZEP: Nikon (AZ100) LV: Nikon LV100/LV150 A: Nikon SMZ18/25 (requires HSMZ1825 adaptor) This indicates whether the stage is encoded or not: 1: Not currently encoded (upgrade available) E: Encoded This indicates the microscope type the stage fits to: E50: Nikon (SS substage) E80: Nikon (SSR substage) AZEP: Nikon (AZ100) NLV: Nikon LV100/LV150
55 Stage Codes for Nikon H112 STAGE FOR UPRIGHT MICROSCOPES H112/2ST This indicates the pitch ball screw: 2: 2 mm ballscrew pitch 5: 5 mm ballscrew pitch This indicates whether the stage is encoded or not: 1: Not currently encoded (upgrade available) E: Encoded H116 STAGE FOR UPRIGHT MICROSCOPES H116/2ST This indicates whether the stage is encoded or not: 1: Not currently encoded (upgrade available) E: Encoded This indicates the pitch ball screw: 2: 2 mm ballscrew pitch 5: 5 mm ballscrew pitch This indicates which microscope the stage fits to: -8: Nikon (LV200 requires H2100 spacer plate and range must be limited to 200mm) H105 STAGE FOR UPRIGHT MICROSCOPES H105/N2F There are currently no encoded variants for the H105/N2F. Z-DECK ZDN12MP This indicates what drives the Z deck: P: Stepper Motor (Unencoded) E: Stepper Motor (Encoded) K: Manual control F: Fixed (no movement possible) H139 MULTI-WELL PLATE STAGE H139#1## This indicates the microscope type the stage fits to: This indicates whether the stage is encoded: 1: Not currently encoded (upgrade available) E: 50 nm encoders NN: Nikon Ti N5: Nikon Ti Note that the suffix alters depending on the presence or absence of encoders. 54
56 More to Prior than meets the eye Since 1919 Prior Scientific has been producing precision equipment for microscopy. With decades of experience, expert staff, a vast range of products and extensive design, manufacture and assembly facilities, Prior Scientific can supply equipment for all manner of microscopy applications. WORLDWIDE DISTRIBUTION Prior Scientific Ltd Cambridge UK Prior Scientific Inc Rockland MA. USA Prior Scientific GmbH Jena Germany Prior Scientific KK Tokyo Japan t: +44 (0) e: uksales@prior.com t: e: info@prior.com t: +49 (0) e: jena@prior.com t: e: info-japan@prior.com 55 Nikon Automation Guide
ProScan DC Linear Servo Stage Technology
ProScan DC Linear Servo Stage Technology www.prior.com Stretching the Boundaries of Performance... Ultra Quiet Operation Can you hear that? Neither can we! Even at high speeds (up to 300 mm/sec) the linear
More informationHLD117 Linear Motor Stage Series
HLD117 Linear Motor Stage Series High Precision Stages with Linear Motor Technology for Leica DM, Nikon Ti and Olympus IX Microscopes Version: 02132014 HLD117DM High Precision Stage with Linear Motor Technology
More informationZ-DECK MANUAL. Z-Deck. Stable platform for electrophysiology and neuroscience Manual Version 2.1. Worldwide distribution
Z-Deck Stable platform for electrophysiology and neuroscience Manual Version 2.1 Worldwide distribution Prior Scientific, Ltd Prior Scientific, Inc Prior Scientific, GmbH Prior Scientific KK Cambridge,
More informationLumaSpec 800S User Manual
LumaSpec 800S User Manual Worldwide distribution VERSION 09112014 Prior Scientific, Ltd Cambridge, UK Prior Scientific, Inc Rockland, MA. USA Prior Scientific, GmbH Jena, Germany Prior Scientific KK Tokyo,
More informationEXC500p-- PATHOLOGY MICROSCOPE. EXC500hd -- HD DIGITAL PATHOLOGY MICROSCOPE. EXC500r -- RESEARCH MICROSCOPE EXC500-LABORATORY SCOPE
EXC500p-- PATHOLOGY MICROSCOPE EXC500hd -- HD DIGITAL PATHOLOGY MICROSCOPE EXC500r -- RESEARCH MICROSCOPE EXC500-LABORATORY SCOPE The EXC500 Pathology and Laboratory Microscope is the most optically advanced
More informationConfocal NEXIV VMZ-K Series. CNC Video Measuring System CONFOCAL NEXIV. VMZ-K Series
Confocal NEXIV VMZ-K Series CNC Video Measuring System CONFOCAL NEXIV VMZ-K Series 3D FOV Measurements Generated with Confocal Images The Confocal NEXIV VMZ-K series, a ground-breaking multifunctional
More informationConfocal NEXIV VMZ-K Series. CNC Video Measuring System CONFOCAL NEXIV. VMZ-K Series
Confocal NEXIV VMZ-K Series CNC Video Measuring System CONFOCAL NEXIV VMZ-K Series The VMZ-K series enables microscopic height measurements using various objective lenses, with two models to choose from,
More informationScanning Ion Conductance Microscope ICnano
Sperm Cell Epithelial Cells I nner Ear Hair Cells I nner Ear Hair Cell Neurons E- Coli Bac teria Scanning Ion Conductance Microscope ICnano About ionscope About ionscope The ionscope scanning ion conductance
More informationIntroduction. Laboratory Equipment & Supplies. Model 1333PHi Shown (Phase Contrast) (2) Eyepieces (Eyecups installed) Diopter Adjustment Mechanism
Introduction With the invention of the microscope in the early 17th century, it was made possible to view objects which were too small for the human eye to see. As the microscope evolved, the structure
More informationInverted Research Microscope. Inverted Research Microscope ECLIPSE Ts2R
Inverted Research Microscope Inverted Research Microscope ECLIPSE Ts2R E a s y t o w o r k w i t h Simple operations Control buttons on the Ts2R microscope are intuitively located for a streamlined workflow.
More informationRyf AG Bettlachstrasse Grenchen tel fax Industrial Microscopes
Ryf AG Bettlachstrasse 2 2540 Grenchen tel 032 654 21 00 fax 032 654 21 09 www.ryfag.ch Industrial Microscopes The ECLIPSE microscope body has been modularized to meet industrial microscope applications
More informationNikon Ti-E Microscope Manual. Rightmire Hall Ohio State University. Director: Tony Brown Rightmire
Nikon Ti-E Microscope Manual Rightmire Hall Ohio State University Director: Tony Brown Rightmire 060 292-1205 brown.2302@osu.edu Facility Manager: Paula Monsma Rightmire 062 293-0939 292-1367 monsma.1@osu.edu
More informationLeica SP8 TCS Users Manual
Version : 07/08/0 Leica SP8 TCS Users Manual Start up:. Turn the PC Microscope, Scanner Power, Laser Power, and the Laser Emission key to on (bottom right of desk).. Turn on the fluorescent lamp (top left
More information2/4/15. Brightfield Microscopy! It s all about Magnification..! or is it?!
Brightfield Microscopy It s all about Magnification.. or is it? 1 What actually does go into chosing a microscope Choice depends on what you need the microscope to do. Do you want to magnify stained specimens?
More informationPWB encoders GmbH Am Goldberg 2 D-99817 Eisenach Germany Phone: +49 3691 72580-0 Fax: +49 3691 72580-29 info@pwb-encoders.com www.pwb-encoders.com 1 of 9 Description The ME22 is a reliable low cost optical
More informationCNC Video Measuring System NEXIV VMZ-K series. CNC Video Measuring System. Confocal Model
CNC Video Measuring System NEXIV VMZ-K series CNC Video Measuring System Confocal Model D FOV Measurements Generated with s A ground-breaking multifunctional video measuring system developed on the strength
More informationSCHOTT Lighting and Imaging. Contents. overview general lighting situations. illumination with fiber optics. direct LED illumination
Contents overview general lighting situations illumination with fiber optics direct LED illumination Illumination Systems with fiber optics KL Series with halogene bulb KL Series with LED light engine
More informationMicro-manipulated Cryogenic & Vacuum Probe Systems
Janis micro-manipulated probe stations are designed for non-destructive electrical testing using DC, RF, and fiber-optic probes. They are useful in a variety of fields including semiconductors, MEMS, superconductivity,
More informationMicroscopy http://www.microscopyu.com/articles/phasecontrast/phasemicroscopy.html http://micro.magnet.fsu.edu/primer/anatomy/anatomy.html 2005, Dr. Jack Ikeda & Dr. Gail Grabner 9 Nikon Labophot (Question
More informationPRECISION CUTTING MICRACUT 202
PRECISION CUTTING MICRACUT 202 MICRACUT 202 MICRACUT 202 precision cutters are used for precise and deformation-free cutting of Metals, Ceramics, Electronic Components, Crystals, Composites, Biomaterials,
More informationUsing Olympus dotslide for polarising microscopy
Using Olympus dotslide for polarising microscopy Background Because the dotslide system is built using a conventional microscope frame it lends itself to acquiring scans in different imaging modes whose
More informationNikon Eclipse Ti A1-A Confocal Operating Manual. Start-up. Microscope
Nikon Eclipse Ti A1-A Confocal Operating Manual Start-up 1. Turn on Excite Fluorescent light power supply- metal halide. a. Cool down as for mercury bulb b. Wheel closed liquid light guide 2. Turn on power
More informationAccessories for the Model 920 Lapping and Polishing Machine
Accessories for the Model 920 Lapping and Machine Applications Laboratory Report Introduction polishing is a common practice in many materials preparation laboratories. Instrumentation for materials processing
More informationno mm no Dividers with scriber 150 mm NEW Square wedge-shaped knife edges on the length side
Summer Promotion valid until 30.06.2013 all quoted prices are incl. VAT for deliveries to EU countries to customers with valid VAT-no. and for deliveries in non EU member countries the VAT is not applicable
More informationFiber Optic Device Manufacturing
Precision Motion Control for Fiber Optic Device Manufacturing Aerotech Overview Accuracy Error (µm) 3 2 1 0-1 -2 80-3 40 0-40 Position (mm) -80-80 80 40 0-40 Position (mm) Single-source supplier for precision
More informationCNC Mill Training System (Heavy Duty)
CNC Mill Training System (Heavy Duty) LabVolt Series Datasheet Festo Didactic en 120 V - 60 Hz 07/2018 Table of Contents General Description 2 Features & Benefits 3 List of Equipment 3 List of Manuals
More information9.07 KINEMATICS KIT USERS MANUAL
9.07 KINEMATICS KIT USERS MANUAL INCLUDED PARTS LIST Standard parts - 1. ground plane enclosure which includes stepper motor with control circuits, press fit motor shaft adaptor, and link attachment plate.
More informationMarch weeks. surcharge for
March weeks valid until 31.03.2012 all quoted prices are incl. 19% VAT for deliveries in the EU countries to customers with a valid VAT-no. and for deliveries in not EU member countries the VAT is not
More informationLaser Systems. !!!! iflex-iris
iflex-iris Laser Systems The Qioptiq iflex-iris solid state laser systems offer high performance stability with low amplitude noise in a miniaturized package. They are ideally suited for integration into
More informationiflex-iris Laser Systems Product features include:
PSM1035 issue 3 iflex-iris Laser Systems The Qioptiq iflex-iris solid state laser systems offer high performance stability with low amplitude noise in a miniaturized package. They are ideally suited for
More informationNanosurf easyscan 2 FlexAFM
Nanosurf easyscan 2 FlexAFM Your Versatile AFM System for Materials and Life Science www.nanosurf.com The new Nanosurf easyscan 2 FlexAFM scan head makes measurements in liquid as simple as measuring in
More informationTouchBright Ver. 7.51
TouchBright Ver. 7.51 High-Performance LED Excitation System Efficient Use Long Lifetime Brightest LEDs Compact Design High-Performance Live Cell Instrument Co., LTD www.touchbrightled.com TouchBright
More informationEasyLED and VisiLED Series. LED Illumination for Stereo Microscopy applications
EasyLED and VisiLED Series LED Illumination for Stereo Microscopy applications SCHOTT LED Illumination Systems for Stereo Microscopy Generations of know-how as clear as glass SCHOTT is a multinational
More informationCharacterization Microscope Nikon LV150
Characterization Microscope Nikon LV150 Figure 1: Microscope Nikon LV150 Introduction This upright optical microscope is designed for investigating up to 150 mm (6 inch) semiconductor wafers but can also
More informationOptical encoder MEC22 HR
Optical encoder MEC22 HR Description The MEC22 HR is a high resolution optical hollow shaft encoder that can be fixed quickly and easily on different sizes of motor shafts. The encoder provides two square
More informationUsing Autofocus in NIS-Elements
Using Autofocus in NIS-Elements Overview This technical note provides an overview of the available autofocus routines in NIS-Elements, and describes the necessary steps for using the autofocus functions.
More informationPERFORMANCE RACING AND ENGINE BUILDING MACHINERY AND EQUIPMENT
PERFORMANCE RACING AND ENGINE BUILDING MACHINERY AND EQUIPMENT F68A Programmable Automatic Machining Center AC Servo Motors and Power Drawbar Hardened Box Way Column Touch Screen Control INDUSTRY EXCLUSIVE
More informationExp. No. 13 Measuring the runtime of light in the fiber
Exp. No. 13 Measuring the runtime of light in the fiber Aim of Experiment The aim of experiment is measuring the runtime of light in optical fiber with length of 1 km and the refractive index of optical
More informationLSM 780 Confocal Microscope Standard Operation Protocol
LSM 780 Confocal Microscope Standard Operation Protocol Basic Operation Turning on the system 1. Sign on log sheet according to Actual start time 2. Check Compressed Air supply for the air table 3. Switch
More informationImageXpress Micro XLS Widefield High Content Screening System. Imaging with a vision.
ImageXpress Micro XLS Widefield High Content Screening System Imaging with a vision www.moleculardevices.com The ImageXpress Micro Widefield High Content Screening System is the ultimate combination of
More informationVision Measuring Systems. KOMEG opti-fix PRE The modular clamping system for vision measuring systems
Vision Measuring Systems KOMEG opti-fix PRE 983040 The modular clamping system for vision measuring systems KOMEG: Noticeably More Experience. Measurably Better Results. KOMEG OPTI-FIX Substantiated experience,
More informationPICO MASTER 200. UV direct laser writer for maskless lithography
PICO MASTER 200 UV direct laser writer for maskless lithography 4PICO B.V. Jan Tinbergenstraat 4b 5491 DC Sint-Oedenrode The Netherlands Tel: +31 413 490708 WWW.4PICO.NL 1. Introduction The PicoMaster
More informationLBM-7 Manual Manipulator
Experts in Electrophysiology & Imaging Micromanipulators LBM-7 Manual Manipulator Compact and robust - 7 axis manual manipulator www.scientifica.uk.com/lbm-7 2 LBM-7 Manipulator Robust yet versatile, manual
More informationYOUNGS MODULUS BY UNIFORM & NON UNIFORM BENDING OF A BEAM
YOUNGS MODULUS BY UNIFORM & NON UNIFORM BENDING OF A BEAM RECTANGULAR BEAM PLACED OVER TWO KNIFE EDGES & DISTANCE BETWEEN KNIFE EDGES IS KEPT CONSTANT AS l= 50cm UNIFORM WEIGHT HANGERS ARE SUSPENDED WITH
More informationSolid Sample Holder Accessory
Installation category I Pollution degree 2 Equipment class III Introduction The Solid Sample Holder for the Agilent Cary Eclipse is an accessory that enables you to perform fluorescence measurements on
More informationiflex-iris Fiber coupled laser systems Product features include:
PSM1041 issue 2 iflex-iris Fiber coupled laser systems The Qioptiq iflex-iris solid state laser systems offer high performance stability with low amplitude noise in a miniaturized package. They are ideally
More informationPROCEEDINGS OF SPIE. Automated asphere centration testing with AspheroCheck UP
PROCEEDINGS OF SPIE SPIEDigitalLibrary.org/conference-proceedings-of-spie Automated asphere centration testing with AspheroCheck UP F. Hahne, P. Langehanenberg F. Hahne, P. Langehanenberg, "Automated asphere
More informationMachine Vision Lyte-MV 2
Machine Vision Lyte-MV 2 The Lyte-MV 2 Range The Lyte-MV 2 provides a reliable industrial light source for a wide range of machine vision applications including triangulation, 3D inspection and alignment.
More informationMetrology Prof. Dr Kanakuppi Sadashivappa Bapuji Institute of Engineering and Technology Davangere. Lecture 24 Measurement of Screw Thread Element
Metrology Prof. Dr Kanakuppi Sadashivappa Bapuji Institute of Engineering and Technology Davangere Lecture 24 Measurement of Screw Thread Element I welcome you all for the module 6 lecture 2, in this lecture
More informationGuide to Confocal 5. Starting session
Guide to Confocal 5 Remember that when booking and before starting session you can check for any problems at https://www.bris.ac.uk/biochemistry/uobonly/cif/index.html Starting session Switch on microscope
More informationLaser Diode Mounting Kits
Laser Diode Mounting Kits For Ø5.6mm and Ø9mm Laser Diodes Complete Mounting System with Collimating Lens If your work involves laser diodes, you ll appreciate the benefits of Optima s laser diode mounting
More informationImaging Introduction. September 24, 2010
Imaging Introduction September 24, 2010 What is a microscope? Merriam-Webster: an optical instrument consisting of a lens or combination of lenses for making enlarged images of minute objects; especially:
More informationOcular Lenses. Head. Arm. Objective Lenses. Slide Holder Stage. On / Off Switch. Condenser with Iris Diaphragm. Light Intensity Control
BIOLOGY 211: HUMAN ANATOMY & PHYSIOLOGY ********************************************************************************************************* USE OF THE LIGHT MICROSCOPE **********************************************************************************************************
More informationStudent, Department of Mechanical Engineering, Knowledge Institute of Technology, Salem, Tamilnadu (1,3)
International Journal of Scientific & Engineering Research, Volume 7, Issue 5, May-2016 11 Combined Drilling and Tapping Machine by using Cone Mechanism N.VENKATESH 1, G.THULASIMANI 2, S.NAVEENKUMAR 3,
More informationOptiSpheric IOL. Integrated Optical Testing of Intraocular Lenses
OptiSpheric IOL Integrated Optical Testing of Intraocular Lenses OPTICAL TEST STATION OptiSpheric IOL ISO 11979 Intraocular Lens Testing OptiSpheric IOL PRO with in air tray on optional instrument table
More informationSystem Options. Magnetic Property Measurement System. AC Susceptibility. AC Susceptibility Specifications
System Options AC Susceptibility Magnetic Property Measurement System Many materials display dissipative mechanisms when exposed to an oscillating magnetic field, and their susceptibility is described
More informationMotion Solutions for Digital Pathology. White Paper
Motion Solutions for Digital Pathology White Paper Design Considerations for Digital Pathology Instruments With an ever increasing demand on throughput, pathology scanning applications are some of the
More informationOPELCO OPtical ELements COrporation LB Objective Series for Biological Use
LB Objective Series for Biological Use 105 Executive Drive Suite 100 Dulles, VA 20166-9558 Tel: (703) 471-0080 S PLAN APOCHROMAT OBJECTIVES These objectives compensate for three wavelength of chromatic
More informationFamily of Stereo Microscopes Quality microscopes for industry and life sciences
SX2 Family of Stereo Microscopes Quality microscopes for industry and life sciences Competitive family of microscopes with first-class performance Precision optics deliver high resolution, flat field and
More informationMiniature collimator for POF fiber: large aperture Model 011-TU2
Example testing Report for: M011-TU2 Miniature collimator for POF fiber: large aperture Model 011-TU2 Testing report Move along this direction to adjust lens Model 011_TU2 with glass lens Part Number:
More information7. Operating instructions: EFL 300
7. Operating instructions: EFL 300 Copyright 2015 by Endecotts Ltd. 59 1. Setting up Technical specifications SIEVE SHAKER MODEL: EFL 300 General Information The new EFL 300 combines the best features
More information» Modular clamping elements for optical or optical/tactical measurement» For high-precision edge measurements in reflected and transmitted light
» Modular clamping elements for optical or optical/tactical measurement» For highprecision edge measurements in reflected and transmitted light» Toothed rails as workpiece stops or for fastening clamping
More informationOTFI 0285 XLM Plus High CRI LED Fiber Optic Light Module with Electronics Key Features
DATASHEET Lighting Solutions XLM Plus High CRI LED Fiber Optic Light Module with Electronics Key Features Color Rendering Index (CRI) over 90 with R9 values typically over 80 Bright Light intensity is
More informationStereomicroscopy. KL1500 LCD and KL 2500 LCD Cold Light Sources. Light Sources for Illumination and Contrasting. Microscopy from Carl Zeiss
Microscopy from Carl Zeiss Stereomicroscopy KL1500 LCD and KL 2500 LCD Cold Light Sources Stereomicroscopy needs a lot of light in a narrow space. With normal light sources this would mean a lot of heat,
More informationMarine Invertebrate Zoology Microscope Introduction
Marine Invertebrate Zoology Microscope Introduction Introduction A laboratory tool that has become almost synonymous with biology is the microscope. As an extension of your eyes, the microscope is one
More informationMotion Solutions for Digital Pathology
Parker Hannifin Electromechanical Dvision N. A. 1140 Sandy Hill Road Irwin, PA 1564203049 724-861-8200 www.parkermotion.com Motion Solutions for Digital Pathology By: Brian Handerhan and Jim Monnich Design
More informationCHX 840 and CHX 1300 CIRCULAR SAW. Versatile sharpening machine for TCT circular saw blades up to 840 or 1300 mm in diameter
CHX 840 and CHX 1300 CIRCULAR SAW Versatile sharpening machine for TCT circular saw blades up to 840 or 1300 mm in diameter CIRCULAR SAW TOOTH FACE AND TOOTH TOP FOR WHEN YOU REQUIRE THAT LITTLE BIT MORE.
More information2. OPERATING PROCEDURES 3. WARNING AND SAFETY HAZARDS 4. QUALITY CONTROL 5. MAINTENANCE 6. INSTALLATION 7. WARRANTY AND LIMITATIONS
SUSS. MJB 3 MASK ALIGNER Operator's Reference Manual Model No. Serial No. Date of Manufacture. 1. GENERAL DESCRIPTION AND PRINCIPLES OF OPERATION ( 2. OPERATING PROCEDURES 3. WARNING AND SAFETY HAZARDS
More informationProfessional In-House PCB Prototyping LPKF ProtoMat Circuit Board Plotters
Professional In-House PCB Prototyping LPKF ProtoMat Circuit Board Plotters Design it. Build it. Today. From design to finished PCB prototype in a few hours - it s possible with LPKF systems. Versatile
More informationHoriba Jobin-Yvon LabRam Raman Confocal Microscope (GERB 120)
Horiba Jobin-Yvon LabRam Raman Confocal Microscope (GERB 120) Please contact Dr. Amanda Henkes for training requests and assistance: 979-862-5959, amandahenkes@tamu.edu Hardware LN 2 FTIR FTIR camera 1
More informationSTC Hydraulic grinding milling machine for cylinder heads and blocks. BERCO S.p.A. A Company of ThyssenKrupp
STC 361-1300 Hydraulic grinding milling machine for cylinder heads and blocks A Company of ThyssenKrupp BERCO S.p.A. The machine and its executions - from grinding wheel to tool: 1 - from tool to milling
More informationMorphologi. Advanced image analysis for high sensitivity particle characterization. Particle size. Particle shape
Particle size Particle shape Morphologi detailed specification sheets from www.malvern.co.uk Introducing a new concept in image analysis The Morphologi high sensitivity particle analyzer is more than just
More informationLeica SP8 Resonant Confocal. Quick-Start Guide
Leica SP8 Resonant Confocal Quick-Start Guide Contents Start-up Preparing for Imaging Part 1 On the scope Part 2 Software interface Part 3 Heat & CO2 incubation Part 4 Other hardware options Shut-down
More informationSpotlight 150 and 200 FT-IR Microscopy Systems
S P E C I F I C A T I O N S Spotlight 150 and 200 FT-IR Microscopy Systems FT-IR Microscopy Spotlight 200 with Frontier FT-IR Spectrometer Introduction PerkinElmer Spotlight FT-IR Microscopy Systems are
More informationHeads AWM-HV VESA Head Dimensions Page 3 SNTB Notebook Holder Page 3
Technical Specification Atdec AWM Series Index Standard Product System Diagram Page 2 Heads AWM-HV VESA Head Dimensions Page 3 SNTB Notebook Holder Page 3 Arms AWM-A13 Overview Page 4 AWM-A46 Dimensions
More informationWSG 8-115; 8-125; P; WSG ; WSG P; WSG PS; WSG P; WSG 15-70Inox
Repair instructions Page of 47 Contents. Models described 2. Technical data 3. Notes and requirements 4. Tools required 5. Lubricants and auxiliary substances required 6. Disassembly 7. Assembly 8. Connection
More informationMODEL G0760 8" X 29" MILL/DRILL w/stand & POWER FEED MANUAL INSERT
MODEL G0760 8" X 29" MILL/DRILL w/stand & POWER FEED MANUAL INSERT The Model G0760 is the same machine as the Model G0705 except the Model G0760 has an X-axis table power feed. Except for the differences
More informationSG100XY. Large Capacity Cylinder Head Seat & Guide Machine. With ACTIV Spindle & Guide-to-Guide Automation
SG100XY Large Capacity Cylinder Head Seat & Guide Machine With ACTIV Spindle & Guide-to-Guide Automation your machining time, productivity and profits! Machining Equipment Created for Performance Racing
More informationABM International, Inc. Navigator Assembly Manual
ABM International, Inc. 1 1.0: Parts List Tablet (Qty. 1) Tablet mount (Qty. 1) NOTE: Mount may appear and operate different then image below Control Box (Qty. 1) Motor Power Supply (Qty. 1) 2 X-axis motor
More informationWafer Loaders for IC Inspection Microscopes NWL200 Series. Wafer Loaders for IC Inspection Microscopes
Wafer Loaders for IC Inspection Microscopes NWL200 Wafer Loaders for IC Inspection Microscopes Wafer Loaders for IC Inspection Microscopes I Nikon s original technology ensures safe, reliable loading of
More informationInstallation Guide. Spherosyn & Microsyn Linear Encoders
Installation Guide Spherosyn & Microsyn Linear Encoders Contents CONTENTS 1. Introduction 1.1 Brackets 1.2 Preparation 1.3 Warnings 2. Spherosyn Encoder Assembly 3. Microsyn Encoder Assembly 4. Mounting
More informationModule 1. Classification of Metal Removal Processes and Machine tools. Version 2 ME IIT, Kharagpur
Module 1 Classification of Metal Removal Processes and Machine tools Lesson 2 Basic working principle, configuration, specification and classification of machine tools Instructional Objectives At the end
More informationMetrology Prof. Dr Kanakuppi Sadashivappa Bapuji Institute of Engineering and Technology Davangere
Metrology Prof. Dr Kanakuppi Sadashivappa Bapuji Institute of Engineering and Technology Davangere Lecture 37 Universal Measuring Machine (UMM) and Coordinate Measuring Machine (CMM) (Refer Slide Time:
More informationOlympus Fluoview 1000S Spectral Confocal Microscope Introduction to the NRI-MCDB Microscopy Facility Spectral Confocal Microscope
Olympus Fluoview 1000S Spectral Confocal Microscope Introduction to the NRI-MCDB Microscopy Facility Spectral Confocal Microscope Improved Optics More Lasers 405 diode 440 diode 488 Argon 515 Argon 559
More informationqueensgate a brand of Elektron Technology
NanoSensors NX/NZ NanoSensor The NanoSensor is a non-contact position measuring system based on the principle of capacitance micrometry. Two sensor plates, a Target and a Probe, form a parallel plate capacitor.
More informationResearch Grade Xenon Arc Lamp Sources LH-Series 75 W - 300W
Research Grade Xenon Arc Lamp Sources LH-Series 75 W - 300W Features Vertical or horizontal bulb and housing operation Xenon arc lamps from 75W to 300W Multiple collimated or focused output optics in various
More informationLast updated: May 2014 Y.DeGraaf
FLINDERS MICROSCOPY BIOMEDICAL SERVICES AVAILABLE MICROSCOPES AND SPECIFICATIONS & INFORMATION REGARDING TRAINING FOR NEW USERS Last updated: May 2014 Y.DeGraaf If you have new staff or students (Honours/Masters
More informationPractical work no. 3: Confocal Live Cell Microscopy
Practical work no. 3: Confocal Live Cell Microscopy Course Instructor: Mikko Liljeström (MIU) 1 Background Confocal microscopy: The main idea behind confocality is that it suppresses the signal outside
More informationBiology 29 Cell Structure and Function Spring, 2009 Springer LABORATORY 1: THE LIGHT MICROSCOPE
Biology 29 Cell Structure and Function Spring, 2009 Springer LABORATORY 1: THE LIGHT MICROSCOPE Prior to lab: 1) Read these instructions (p 1-6) 2) Go through the online tutorial, the microscopy pre-lab
More informationQuality Performance, Innovative Design
Dimensions Confocal Laser Scanning Biological Microscope Table size (mm): 1400(W) 800(D) * Table is not available from Olympus. Avoid placing the controller directly on the floor. Dimensions / Weight /
More informationAxminster Single Hinge Jig
Code 100714 Axminster Single Hinge Jig (Clamp not supplied) Index of Contents Page Index of Contents 2 Copyright 2 Introduction 3 What s in the Box 3 General Instructions for Working Practice/Safety 3
More informationHow to align your laser for two-photon imaging
How to align your laser for two-photon imaging Two-photon microscopy uses a laser to excite fluorescent molecules (fluorophores) within a sample through emitting short pulses of light at high power. This
More informationHybrid Surface Contour Measuring Machine FORMTRACER CS-5000
Form Measurement Hybrid Surface Contour Measuring Machine FORMTRCER CS-5000 CTLOG No. E4220-525 hybrid surface contour measuring machine that combines contour and surface roughness measurements and analyses
More informationMLA 150 (DLA) Presentation and examples. Théophane Besson, , Heidelberg Instruments GmbH 1
MLA 150 (DLA) Presentation and examples Théophane Besson, 17.03.2015, Heidelberg Instruments GmbH 1 Presentation of the tool The MLA 150 (named DLA in the past) is a new generation Maskless Aligner developed
More informationQUICKSTART GUIDE: WIDEFIELD HWF1 Zeiss Cell Observer Live Cell Imaging System (HAMMERSMITH, L BLOCK, ROOM 314) Imperial College London
Imperial College London Facility for Imaging by Light Microscopy QUICKSTART GUIDE: WIDEFIELD HWF1 Zeiss Cell Observer Live Cell Imaging System (HAMMERSMITH, L BLOCK, ROOM 314) Observing Life As It Happens
More informationIntroduction of New Products
Field Emission Electron Microscope JEM-3100F For evaluation of materials in the fields of nanoscience and nanomaterials science, TEM is required to provide resolution and analytical capabilities that can
More informationFAQs. Not directly. The pe-100 Control Pod does have a BNC connector to allow for TTL triggering.
pe-100 FAQs Can it be controlled through software? Not directly. The pe-100 Control Pod does have a BNC connector to allow for TTL triggering. What are the combination options? There is currently a choice
More informationLBM7 Manual Manipulator
LBM7 Manual Manipulator Copyright Scientifica Ltd 1998 All Rights Reserved 1 TABLE OF CONTENTS 1. INTRODUCTION 1.1. Overview 2. INITIAL INSPECTION 2.1. Visual Inspection 2.2. Quality Control 3. INSTALLATION
More informationData Sheet MEM 16. Incremental Encoder Magnetic
Incremental Encoder Magnetic PWB encoders GmbH Am Goldberg 2 D-99817 Eisenach Germany Phone: +49 3691 72580-0 Fax: +49 3691 72580-29 info@pwb-encoders.com MEM16IE Rev.2.1 / 15.12.2016 info@pwb-encoders.com
More informationCrystalPro is a computer-controlled microscope with top quality optics.
CrystalPro is a computer-controlled microscope with top quality optics. CrystalPro has been optimised for visualising protein crystallography experiments. Its proprietary illumination system utilises both
More information