Laser Speckle Reducer LSR-3000 Series

Size: px
Start display at page:

Download "Laser Speckle Reducer LSR-3000 Series"

Transcription

1 Datasheet: LSR-3000 Series Update: Copyright 2012 Optotune Laser Speckle Reducer LSR-3000 Series Speckle noise from a laser-based system is reduced by dynamically diffusing the laser beam. A diffuser is bonded to a thin elastic membrane, which includes four independent electo-active polymer electrodes that induce a circular oscillation of the diffuser in x- and y-direction. The LSR-3000 Series integrates fully certified drive electronics powered through a single micro-usb connector. Two sizes are available: the LSR-3005 and the LSR-3010 that respectively exhibit a clear aperture of 5 mm and 10 mm. The following table outlines the specification of Optotune s LSR-3000 Series. The diffusion angle can be adapted on demand. Mechanical specifications LSR-3005 LSR-3010 Clear aperture 5 10 mm Outer diameter mm Thickness mm Weight g Electrical specifications 1 Power supply (micro-usb interface) 5 5 VDC Power consumption mw Optical specifications Diffusion angle (FWHM) 1 /10 /20 1 /10 /20 Transmission spectrum 2 see figures 2&3 see figures 2&3 Damage threshold 2 >3 >3 W/cm 2 Oscillation frequency ~300 ~180 Hz Oscillation amplitude ~400 ~400 µm Thermal specifications Storage temperature [-40,+85] [-40,+85] C Operating temperature [-30,+85] [-30,+85] C Figure 1 (a-c) show the effect of the LSR-3005 on a laser spot (= 650 nm, P = 5 mw). (a) Without LSR (b) with LSR OFF (c) with LSR ON Figure 1: CCD images of a laser spot without and with LSR-3005 on VAC to 5 VDC micro-usb power supply provided by Optotune 2 The standard LSR comes with polycarbonate diffusers. On request, custom diffusers made of proprietary polymers are available, which offer a higher transmission range and a damage threshold of 300 W/cm 2. Furthermore, it is possible to build LSRs with coated glass diffusers of similar size and weight. Page 1 of 4

2 Datasheet: LSR-3000 Series Update: Copyright 2012 Optotune The following two figures show the transmission spectrum of the LSR-3000 Series with standard polycarbonate diffusers and coated BK7 cover glasses. In addition to the dynamic diffuser, standard products ship with a 1 static diffuser to increase speckle reduction efficiency. Transmission [%] LSR-3000 VIS, 1 dynamic, no static diffusor LSR-3000 VIS, 10 dynamic, no static diffusor 20 LSR-3000 VIS, 20 dynamic, no static diffusor LSR-3000 VIS, 1 dynamic and 1 static diffusor 10 LSR-3000 VIS, 10 dynamic and 1 static diffusor LSR-3000 VIS, 20 dynamic and 1 static diffusor Wavelength [nm] Figure 2: Transmission spectrum of the LSR-3000 series with VIS-coated cover glasses (0 angle of incidence) Transmission [%] LSR-3000 NIR, 1 dynamic, no static diffusor LSR-3000 NIR, 10 dynamic, no static diffusor 20 LSR-3000 NIR, 20 dynamic, no static diffusor LSR-3000 NIR, 1 dynamic and 1 static diffusor 10 LSR-3000 NIR, 10 dynamic and 1 static diffusor LSR-3000 NIR, 20 dynamic and 1 static diffusor Wavelength [nm] Figure 3: Transmission spectrum of the LSR-3000 series with NIR-coated cover glasses (0 angle of incidence) Page 2 of 4

3 Datasheet: LSR-3000 Series Update: Copyright 2012 Optotune Figure 4 shows the dimensions of the LSR-3005 (left) and of the LSR-3010 (right). The housing exhibits a M4 thread in order to facilitate the integration of the LSR on an optical table. The power supply interface is made through a micro-usb connector. The LSR-3000 series is also available without housing (see datasheet of LSR- OEM) Figure 4: Mechanical drawing of the LSR-3005 (left) and of the LSR-3010 (right) (unit: mm) Ordering information for standard products The LSR-3000 can be delivered with two sizes of clear aperture, three different diffusing angles (circular) and two types of cover glasses. When ordering, please refer to these specifications as follows: LSR-30CA--AR CA = Clear aperture (05 or 10 mm) = Diffusion angle (1, 10 or 20 ) AR= Antireflection coating (VIS or NIR 3 ) Example: LSR VIS refers to a speckle reducer of 5 mm aperture with a diffusion angle of 20 and VIS coated cover glasses. Custom products Optotune offers customized versions of the LSR. This datasheet only contains variations of the LSR-3000 Series products. For LSRs with substantially smaller or larger apertures, please contact sales@optotune.com. Diffusers In principle, any type of diffuser can be used as long as size and weight are similar to the standard polycarbonate diffuser. Optotune has several types of polycarbonate diffusers in stock (circular: 0.5, 2, 3, 5, 30, 3 By standard, the NIR version is only available for the LSR-3005 Page 3 of 4

4 Datasheet: LSR-3000 Series Update: Copyright 2012 Optotune 40, elliptical: on demand e.g. 40 x0.1 ) and can also produce diffusers of a proprietary polymer material, which offers a higher transmission range (see Figure 5) and a damage threshold of 300 W/cm 2. Furthermore, it is possible to use specialty coated glass diffusers if they are light enough. If necessary, it is also possible to remove the membrane from the optical path. The following table summarizes these options: Diffuser type Polycarbonate (standard) Optotune proprietary polymer Glass diffusers (typical) Thickness 250 um um As thin as possible Density 1.2 g/cm g/cm g/cm 3 Weight 5 mm aperture 10mm aperture Transmission range Damage threshold 8.5 mg 28.5 mg mg mg up to 20 mg up to 70 mg nm nm nm (depending on material) > 3W/cm 2 > 300 W/cm 2 1 kw/cm 2 (depending on material) Please note that diffusers cannot be exchange after the LSR has been produced. Also, when using customized diffusers it might be necessary to select an appropriate cover glass to match the transmission range. Figure 5: Comparison of standard polycarbonate diffusers and Optotune s proprietary diffuser material Cover glasses Cover glasses can be customized with respect to material and antireflection coating. The standard cover glasses are VIS or NIR coated BK7. If the LSR is to be integrated into a clean environment, then the cover glasses can be omitted. Frequency The oscillation frequency is set to the measured resonant frequency of the LSR during production. With the current standard electronics it is not possible to change that frequency after production. However, Optotune can provide customized electronics to control both voltage and frequency of the electro-active polymer. Page 4 of 4

5 Application Note: Transmissive Laser Speckle Reducer LSR-3000 & LSR-OEM Series Page 1 of 11

6 Speckle pattern Lasers have the unique characteristic to provide high power and low divergent light. Besides, due to its working principle, laser light exhibits a high degree of coherence that enables, e.g. efficient interference processes. Although this characteristic is widely used in many scientific systems, it leads to a significant drawback for applications that use a light detector. When shining a surface, laser light is scattered by each corrugation points of the illuminated surface. Each of these scattered points may be described as secondary coherent light sources. If the corrugation depth is of the order of the laser wavelength, local interferences occur such that a random intensity pattern also known as speckle pattern is observed. Figure 1 shows an image and the corresponding intensity profile of a speckle pattern. (a) (b) Figure 1 (a) Image of a speckle pattern on a CCD camera (b) Measured intensity profile on a horizontal axis through the spots center. This non-uniform intensity distribution puts significant constraints on light detectors that exhibit local saturation points. Besides, this pattern may disturb the human eye. Speckle reduction Speckle contrast The speckle contrast S is defined as the standard deviation of the intensity I i within a certain area normalized by its mean value I mean as shown in Eq. 1 hereunder. (1) with (2) The speckle contrast varies between 0 and 1, 0 representing a homogenous beam without speckles. Page 2 of 11

7 Reduction factor At a microscopic level, the speckle ratio depends on The wavelength of the laser light The state of polarization of the laser light These two parameters are well defined with laser light and contribute together with the quality of the illuminated surface to the speckle process. At a fixed wavelength and state of polarization, the better the quality of the illumination surface, the smaller is the speckle contrast. Alternatively, for a fixed surface quality, the larger the wavelength, the lower is the speckle contrast. At a macroscopic level, the speckle ratio depends on: The diffusion angle of the LSR The numerical aperture of the detection system The reduction factor is in this last case of:, where is the diffusion angle and is the numerical aperture of the detection system. Reduction efficiency For a reference optical system, the reduction efficiency R may be described as the ratio between speckle contrast without LSR S and the speckle contrast with LSR S LSR as follow: (3) For instance a reduction of the speckle ratio from 0.5 to 0.2 provides a reduction efficiency of 4 db. : working principle The laser speckle reducer from Optotune is based on a dynamic process. The speckle pattern is moved at a sufficiently high frequency and amplitude such that the detection system integrates the speckle pattern over time as a uniform light distribution. The LSR consists of a diffuser bonded on a polymer membrane that includes four independent dielectric elastomer actuators (DEAs). Under activation, the surface of the electrodes increases and causes a motion of the rigid diffuser in the membrane plane. The four independent electrodes are used to obtain displacement of the diffuser in both directions of the x- and y-axis, as shown in Figure 2. In case of the LSR-3000, the control signals of the four electrodes (x1, y1, x2 and y2) have the same amplitude and frequency, but with a phase shift of 90 in between. This controlling profile of the electrical signals driving the electrodes generates a circular motion of the diffuser. The moving frequency is optimal when reaching the mechanical resonance frequency of the system und such provides the highest speckle reduction. Page 3 of 11

8 Figure 2: Illustration of four independent DEAs to move the rigid diffuser (blue circle) in the plane of the membrane. The equilibrium (no voltage applied on the electrodes) position of the diffuser is represented by the dashed circle. (a) The x1 and y1 electrodes are activated, the diffuser moves in positive x- and y-direction. In the pictures (b), (c) and (d) the analog effect as described for all four different states of the diffuser. After reaching state (d), the cycle continues with position (a). A dedicated driving electronic that provides the optimal electrical control signal is integrated in the LSR-3000 and energized by a 5V Micro-USB power supply. Measurement of the speckle reduction Reference setup In our reference setup, the LSR is positioned in a collimated laser beam of 5 mm as shown in Figure 3. Figure 3 : Reference setup for measuring speckle reduction. Laser: He-Ne, P=20mW, λ=632.8nm, linearly polarized. Beam expander: 15x. Objective: Computar, T4Z2813 CS IR. Camera: Mightex Systems, Monochrome 1.3MP CMOS, MCE-B013-US USB2.0. The laser light is expanded up to a 5mm diameter collimated beam by a beam expander. An attenuator at the input of the beam expander controls the laser power. Likewise an aperture can be used at the output of the beam expander to precisely control the illumination beam size and minimize stray light on the screen at the very end of the bench. The transmissive LSR is positioned in the collimated beam after the aperture and an image of the laser spot on the screen is made by the camera. Page 4 of 11

9 Figure 4 shows typical speckle images that are obtained without any LSR (a), with the LSR in a static mode (b) and with the LSR in a dynamic mode (c). The colored lines show the horizontal plane in which the intensity profiles are measured and depicted in Figure 5. (a) (b) (c) Figure 4: Typical images of the speckle contrast measured on the reference setup (a) without LSR in the collimated path (b) with the LSR in a static mode (c) with the LSR in a dynamic mode. The colored lines show the cut planes that refer to Figure 5. Figure 5 shows the corresponding intensity profile of the images of Figure 4 in a horizontal plane. Figure 5 Measurement of the speckle contrast on a horizontal plan as depicted in Figure 4. In red, without any LSR, in yellow with the LSR in a static mode and in blue with the LSR in a dynamic mode. The same characterization method is applied to all our standard LSR and the results are introduced in the following section. Page 5 of 11

10 Results on standard products of the LSR-3000 Series LSR (5mm aperture, 20 diffusion angle, ~3um structure size) Reduction efficiency R = 15 db Figure 6: Measurement of the intensity profile: in red, without LSR (laser alone) and in blue with the LSR LSR (5mm aperture, 10 diffusion angle, ~20um structure size) Reduction efficiency R = 12 db Figure 7: Measurement of the intensity profile: in red, without LSR (laser alone) and in blue with the LSR LSR (5mm aperture, 1 diffusion angle, ~100um structure size) Reduction efficiency R = 6 db Figure 8: Measurement of the intensity profile: in red, without LSR (laser alone) and in blue with the LSR Page 6 of 11

11 Key parameters for efficient speckle reduction The resulting speckle reduction depends on a number of parameters including: Motion speed of the diffuser Diffuser structure Exposure time of the observer/camera Optical system layout (beam diameter, position of LSR, additional optics) Displacement Resonant frequency Diffuser structure size The higher the better Depends on: LSR size (larger = higher) Diffuser weight Maximum voltage Material parameters The higher the better Depends on LSR size (larger = lower) Diffuser weight Material parameters The smaller the better Various approaches: Random surface diffusers Diffractive optical elements (DOE) Figure 9: Summary of key parameters for efficient speckle reduction High motion speed The diffuser moves along a circle (or ellipse) due to the activation cycles of the electrodes. The main parameters of the actuation are: The motion amplitude (path perimeter L = 2π r ) The mechanical driving frequency f Together, these two parameters define the motion speed of the diffuser v=l f Example of LSR-3005: r=200um, f=300hz v=377mm/s The higher the motion speed of the diffuser, the more patterns can be overlapped during the exposure time of the observer. This parameter can be optimized for custom designs, but there are trade-offs to be made between motion amplitude, frequency, size of the LSR, weight of the diffuser and maximum voltage. Diffuser structures Speckle reduction efficiency is proportional to the number of structures passing under a point during exposure time. The addition of N uncorrelated speckle patterns yield a reduction of speckle contrast by 1/SQRT(N). The goal is thus to create as many uncorrelated speckle patterns as possible. Apart from moving the diffuser as much and as fast as possible (high motion speed), this can be influenced by optimizing the structure of the diffuser. As can be seen on page 6, the reduction efficiency is better with smaller structures. But that means higher angles, which again leads to a trade-off with beam divergence. Page 7 of 11

12 Optotune is working on optimized diffuser structures or the use of diffractive optical elements (DOEs) to achieve efficient speckle reduction at minimal increase of divergence. Exposure time Ideally, the frequency of the LSR is at least as high as the frame rate of the camera. In the case of the human eye, which has exposure time of about 17ms (60Hz), this is easy to achieve. An industrial camera, however, might run at higher rates. For example, the LSR-3005 runs at 300Hz, which corresponds to an exposure time of 3.3ms. If the exposure time of a camera is 1ms, then only about one third of the circular motion is captured, so the speckle reduction will be less. However, depending on the motion amplitude and the structure size of the diffuser, the reduction might still be very good. The LSR can still reduce the speckle contrast down to 3% for a 1ms exposure time as can be seen in Figure 10. Unfortunately at a MHz level, the speckle reduction process will not be efficient. Figure 10: Speckle contrast obtained by the LSR for an integration time from 1ms to 10ms How to optimise the integration of the LSR in a laser system For efficient laser speckle reduction, we advise to: position the LSR perpendicular to the optical axis illuminate the LSR by a collimated beam match the beam size that enter the LSR with its clear aperture ( 5mm diameter) Figure 11 illustrates the most straight-forward use of the LSR. The laser beam is collimated and its cross-section matches the clear aperture of the LSR. The zoom in Figure 11 shows the correct positioning of the LSR along the light path. The cone-shaped aperture corresponds to the light output. Page 8 of 11

13 Figure 11: Optimal use and positioning of the LSR in a laser system Under this configuration, from the optical point of view, the LSR will expand the collimated beam with an angle that matches its diffusion angle (e.g. 20 FWHM value for the LSR ). In order to compensate for the diffusion angle, a collimation lens can be positioned downstream the LSR at a distance that matches its focal length in order to re-collimate the beam. This setup is illustrated in Figure 12. Figure 12: Optimal use of the LSR in a laser system with an optical system positioned upstream the LSR. Page 9 of 11

14 LSR in focal plane + homogenizer An alternative use of the LSR is to position it in the focal point of the laser. Acting as a point source, the beam can be very well collimated again. However, the diffuser structure becomes visible, which means a homogenizer is needed. The result is a speckle-free, collimated and homogeneous beam. LSR-3000 micro-lens array condensor field lens Laser screen Figure 13: Optical system layout with the LSR in the focal place of the laser, followed by a homogenizer LSR for use with DLP/LCOS micro displays In the following, three principle setups are described for the integration of the LSR into a projection system based on DLP or LCOS micro displays. Red Laser Collimation lenses Optotune LSR Beam homogenizer DLP/LCOS Projection Optics Green Laser Blue Laser Beam combiner Collecting lens Homogen, collimated, speckle free beam Figure 14: LSR is positioned before the micro display to illuminate the DLP/LCOS with speckle-free light Red Laser Collimation lenses Beam homogenizer DLP/LCOS Optotune LSR Projection Optics Green Laser Blue Laser Beam combiner Homogen, collimated beam Figure 15: The LSR positioned after the micro display in the image plane of the projection optics. The Image stays in focus thanks to minimal out-of-plain motion of the LSR Page 10 of 11

15 Red Laser Optotune LSR Beam combiner Beam homogenizer DLP/LCOS Projection Optics Green Laser Blue Laser Collimation optics Homogen, collimated, speckle free beam Figure 16: Each laser is despeckled separately. Glass diffusers with wavelength optimized coatings can be used. Trouble shooting The output beam does not exhibit any speckle reduction at all 1. Check that the power supply is on (blue light). 2. Check that a significant difference is obtained when the LSR is switched on (dynamic mode, Figure 4 (c)) compared to when the LSR is switched OFF (static mode, Figure 4 (b)) 3. To check if the diffuser is moving at all, place the diffuser into the focal point to make an image of the diffuser structure on the screen. Thanks to the magnification, the movement should be very apparent. 4. If none of the above solves your problem, this means the LSR is broken and should be sent back to Optotune for replacement. The output beam does not exhibit a sufficient speckle reduction 1. Try to optimize the speckle reduction by increasing the size of the input beam to match the size of the clear aperture of the LSR. 2. Try to optimize the position of the LSR perpendicular to the optical axis. 3. Try to increase the exposure time of your camera. 4. If none of the above solves your problem, this means the chosen LSR does not provide a sufficient speckle reduction ratio R for your application. A LSR with a larger diffusion angle should be used. Custom designs Optotune can design a dedicated LSR for your application, taking into account requirements for size, frequency and motion amplitude. It is also possible to integrate custom diffusers of your choosing. Feel free to ask for a feasibility study or a quote at: sales@optotutne.com. Page 11 of 11

Laser Speckle Reducer LSR-3000 Series

Laser Speckle Reducer LSR-3000 Series Laser Speckle Reducer LSR-3000 Series Speckle noise from a laser-based system is reduced by dynamically diffusing the laser beam. A diffuser is bonded to a thin elastic membrane, which includes four independent

More information

Miniaturized Laser Speckle Reducer OEM Series

Miniaturized Laser Speckle Reducer OEM Series Miniaturized Laser Speckle Reducer OEM Series Speckle noise from a laser-based system is reduced by dynamically diffusing the laser beam. A diffuser is bonded to a thin elastic membrane, which includes

More information

Miniaturized Laser Speckle Reducer OEM Series

Miniaturized Laser Speckle Reducer OEM Series Miniaturized Laser Speckle Reducer OEM Series Speckle noise from a laser-based system is reduced by dynamically diffusing the laser beam. A diffuser is bonded to a thin elastic membrane, which includes

More information

Compact and Reliable Speckle Reduction

Compact and Reliable Speckle Reduction Compact and Reliable Speckle Reduction August 2017 Mark Ventura, Vice President Sales & Marketing Optotune Switzerland AG Bernstrasse 388 CH-8953 Dietikon Switzerland Phone +41 58 856 3011 www.optotune.com

More information

Speckle free laser projection

Speckle free laser projection Speckle free laser projection With Optotune s Laser Speckle Reducer October 2013 Dr. Selina Casutt, Application Engineer Bernstrasse 388 CH-8953 Dietikon Switzerland Phone +41 58 856 3011 www.optotune.com

More information

Diffuser / Homogenizer - diffractive optics

Diffuser / Homogenizer - diffractive optics Diffuser / Homogenizer - diffractive optics Introduction Homogenizer (HM) product line can be useful in many applications requiring a well-defined beam shape with a randomly-diffused intensity profile.

More information

Will contain image distance after raytrace Will contain image height after raytrace

Will contain image distance after raytrace Will contain image height after raytrace Name: LASR 51 Final Exam May 29, 2002 Answer all questions. Module numbers are for guidance, some material is from class handouts. Exam ends at 8:20 pm. Ynu Raytracing The first questions refer to the

More information

Speckle Mitigation in Laser-Based Projectors

Speckle Mitigation in Laser-Based Projectors Speckle Mitigation in Laser-Based Projectors Fergal Shevlin, Ph.D. CTO, Dyoptyka. Laser Display Conference, Yokohama, Japan, 2012/04/26-27. What does speckle look like? Can speckle be reduced? How can

More information

Machine Vision Lyte-MV 2

Machine Vision Lyte-MV 2 Machine Vision Lyte-MV 2 The Lyte-MV 2 Range The Lyte-MV 2 provides a reliable industrial light source for a wide range of machine vision applications including triangulation, 3D inspection and alignment.

More information

Laser Scanning 3D Display with Dynamic Exit Pupil

Laser Scanning 3D Display with Dynamic Exit Pupil Koç University Laser Scanning 3D Display with Dynamic Exit Pupil Kishore V. C., Erdem Erden and Hakan Urey Dept. of Electrical Engineering, Koç University, Istanbul, Turkey Hadi Baghsiahi, Eero Willman,

More information

Design Description Document

Design Description Document UNIVERSITY OF ROCHESTER Design Description Document Flat Output Backlit Strobe Dare Bodington, Changchen Chen, Nick Cirucci Customer: Engineers: Advisor committee: Sydor Instruments Dare Bodington, Changchen

More information

EE119 Introduction to Optical Engineering Spring 2003 Final Exam. Name:

EE119 Introduction to Optical Engineering Spring 2003 Final Exam. Name: EE119 Introduction to Optical Engineering Spring 2003 Final Exam Name: SID: CLOSED BOOK. THREE 8 1/2 X 11 SHEETS OF NOTES, AND SCIENTIFIC POCKET CALCULATOR PERMITTED. TIME ALLOTTED: 180 MINUTES Fundamental

More information

Chapter Ray and Wave Optics

Chapter Ray and Wave Optics 109 Chapter Ray and Wave Optics 1. An astronomical telescope has a large aperture to [2002] reduce spherical aberration have high resolution increase span of observation have low dispersion. 2. If two

More information

Supplementary Figure 1. Effect of the spacer thickness on the resonance properties of the gold and silver metasurface layers.

Supplementary Figure 1. Effect of the spacer thickness on the resonance properties of the gold and silver metasurface layers. Supplementary Figure 1. Effect of the spacer thickness on the resonance properties of the gold and silver metasurface layers. Finite-difference time-domain calculations of the optical transmittance through

More information

Laser and LED retina hazard assessment with an eye simulator. Arie Amitzi and Menachem Margaliot Soreq NRC Yavne 81800, Israel

Laser and LED retina hazard assessment with an eye simulator. Arie Amitzi and Menachem Margaliot Soreq NRC Yavne 81800, Israel Laser and LED retina hazard assessment with an eye simulator Arie Amitzi and Menachem Margaliot Soreq NRC Yavne 81800, Israel Laser radiation hazard assessment Laser and other collimated light sources

More information

BEAMAGE-3.0 KEY FEATURES BEAM DIAGNOSTICS AVAILABLE MODELS MAIN FUNCTIONS SEE ALSO ACCESSORIES. CMOS Beam Profiling Cameras

BEAMAGE-3.0 KEY FEATURES BEAM DIAGNOSTICS AVAILABLE MODELS MAIN FUNCTIONS SEE ALSO ACCESSORIES. CMOS Beam Profiling Cameras BEAM DIAGNOSTICS BEAM DIAGNOSTICS SPECIAL PRODUCTS OEM DETECTORS THZ DETECTORS PHOTO DETECTORS HIGH POWER DETECTORS POWER DETECTORS ENERGY DETECTORS MONITORS CMOS Beam Profiling Cameras AVAILABLE MODELS

More information

ARCoptix. Radial Polarization Converter. Arcoptix S.A Ch. Trois-portes Neuchâtel Switzerland Mail: Tel:

ARCoptix. Radial Polarization Converter. Arcoptix S.A Ch. Trois-portes Neuchâtel Switzerland Mail: Tel: ARCoptix Radial Polarization Converter Arcoptix S.A Ch. Trois-portes 18 2000 Neuchâtel Switzerland Mail: info@arcoptix.com Tel: ++41 32 731 04 66 Radially and azimuthally polarized beams generated by Liquid

More information

Laser Telemetric System (Metrology)

Laser Telemetric System (Metrology) Laser Telemetric System (Metrology) Laser telemetric system is a non-contact gauge that measures with a collimated laser beam (Refer Fig. 10.26). It measure at the rate of 150 scans per second. It basically

More information

Optical basics for machine vision systems. Lars Fermum Chief instructor STEMMER IMAGING GmbH

Optical basics for machine vision systems. Lars Fermum Chief instructor STEMMER IMAGING GmbH Optical basics for machine vision systems Lars Fermum Chief instructor STEMMER IMAGING GmbH www.stemmer-imaging.de AN INTERNATIONAL CONCEPT STEMMER IMAGING customers in UK Germany France Switzerland Sweden

More information

Optical Information. The LDM145 laser diode modules are available with the following lens types.

Optical Information. The LDM145 laser diode modules are available with the following lens types. LDM145 Datasheet LDM145 The LDM145 is a 16mm diameter CW laser diode module available in wavelengths of 520, 635, 650, 670, 780 & 850nm with power of up to 5mW as standard. It reuires an operating voltage

More information

Collimation Tester Instructions

Collimation Tester Instructions Description Use shear-plate collimation testers to examine and adjust the collimation of laser light, or to measure the wavefront curvature and divergence/convergence magnitude of large-radius optical

More information

Be aware that there is no universal notation for the various quantities.

Be aware that there is no universal notation for the various quantities. Fourier Optics v2.4 Ray tracing is limited in its ability to describe optics because it ignores the wave properties of light. Diffraction is needed to explain image spatial resolution and contrast and

More information

SUPPLEMENTARY INFORMATION

SUPPLEMENTARY INFORMATION Optically reconfigurable metasurfaces and photonic devices based on phase change materials S1: Schematic diagram of the experimental setup. A Ti-Sapphire femtosecond laser (Coherent Chameleon Vision S)

More information

Where λ is the optical wavelength in air, V a is the acoustic velocity, and f is the frequency bandwidth. Incident Beam

Where λ is the optical wavelength in air, V a is the acoustic velocity, and f is the frequency bandwidth. Incident Beam Introduction to A-O Deflectors/Scanners An acoustic deflector/scanner changes the angle of direction of a laser beam and its angular position is linearly proportional to the acoustic frequency, so that

More information

Laser Beam Analysis Using Image Processing

Laser Beam Analysis Using Image Processing Journal of Computer Science 2 (): 09-3, 2006 ISSN 549-3636 Science Publications, 2006 Laser Beam Analysis Using Image Processing Yas A. Alsultanny Computer Science Department, Amman Arab University for

More information

Adaptive Optics for LIGO

Adaptive Optics for LIGO Adaptive Optics for LIGO Justin Mansell Ginzton Laboratory LIGO-G990022-39-M Motivation Wavefront Sensor Outline Characterization Enhancements Modeling Projections Adaptive Optics Results Effects of Thermal

More information

ERS KEY FEATURES BEAM DIAGNOSTICS MAIN FUNCTIONS AVAILABLE MODEL. CMOS Beam Profiling Camera. 1 USB 3.0 for the Fastest Transfer Rates

ERS KEY FEATURES BEAM DIAGNOSTICS MAIN FUNCTIONS AVAILABLE MODEL. CMOS Beam Profiling Camera. 1 USB 3.0 for the Fastest Transfer Rates POWER DETECTORS ENERGY DETECTORS MONITORS SPECIAL PRODUCTS OEM DETECTORS THZ DETECTORS PHOTO DETECTORS HIGH POWER DETECTORS CAMERA PROFIL- CMOS Beam Profiling Camera KEY FEATURES ERS 1 USB 3.0 for the

More information

Information & Instructions

Information & Instructions KEY FEATURES 1. USB 3.0 For the Fastest Transfer Rates Up to 10X faster than regular USB 2.0 connections (also USB 2.0 compatible) 2. High Resolution 4.2 MegaPixels resolution gives accurate profile measurements

More information

Sensitive measurement of partial coherence using a pinhole array

Sensitive measurement of partial coherence using a pinhole array 1.3 Sensitive measurement of partial coherence using a pinhole array Paul Petruck 1, Rainer Riesenberg 1, Richard Kowarschik 2 1 Institute of Photonic Technology, Albert-Einstein-Strasse 9, 07747 Jena,

More information

PRELIMINARY. EL-6-18-VIS-LD Dimensions (L x W x H) 18 x 19.3 x 8.7 mm Clear aperture 6 mm Weight 6.7 g Lifecycles (10-90% sinusoidal) >

PRELIMINARY. EL-6-18-VIS-LD Dimensions (L x W x H) 18 x 19.3 x 8.7 mm Clear aperture 6 mm Weight 6.7 g Lifecycles (10-90% sinusoidal) > Fast EL-6-18 The curvature of this shape changing polymer lens can be adjusted by applying current. The focal length is accordingly tuned to a desired value within milliseconds. The following table outlines

More information

The LINOS Singlets. Our quality criteria:

The LINOS Singlets. Our quality criteria: The LINOS From convergent lenses and diffuse lenses to best form lenses and aspheres, our extensive selection of simple lenses, or singlets, with various focal lengths and diameters guarantees that you

More information

EXPRIMENT 3 COUPLING FIBERS TO SEMICONDUCTOR SOURCES

EXPRIMENT 3 COUPLING FIBERS TO SEMICONDUCTOR SOURCES EXPRIMENT 3 COUPLING FIBERS TO SEMICONDUCTOR SOURCES OBJECTIVES In this lab, firstly you will learn to couple semiconductor sources, i.e., lightemitting diodes (LED's), to optical fibers. The coupling

More information

Tutorial Zemax 9: Physical optical modelling I

Tutorial Zemax 9: Physical optical modelling I Tutorial Zemax 9: Physical optical modelling I 2012-11-04 9 Physical optical modelling I 1 9.1 Gaussian Beams... 1 9.2 Physical Beam Propagation... 3 9.3 Polarization... 7 9.4 Polarization II... 11 9 Physical

More information

UV EXCIMER LASER BEAM HOMOGENIZATION FOR MICROMACHINING APPLICATIONS

UV EXCIMER LASER BEAM HOMOGENIZATION FOR MICROMACHINING APPLICATIONS Optics and Photonics Letters Vol. 4, No. 2 (2011) 75 81 c World Scientific Publishing Company DOI: 10.1142/S1793528811000226 UV EXCIMER LASER BEAM HOMOGENIZATION FOR MICROMACHINING APPLICATIONS ANDREW

More information

BMC s heritage deformable mirror technology that uses hysteresis free electrostatic

BMC s heritage deformable mirror technology that uses hysteresis free electrostatic Optical Modulator Technical Whitepaper MEMS Optical Modulator Technology Overview The BMC MEMS Optical Modulator, shown in Figure 1, was designed for use in free space optical communication systems. The

More information

Supplementary Information for. Surface Waves. Angelo Angelini, Elsie Barakat, Peter Munzert, Luca Boarino, Natascia De Leo,

Supplementary Information for. Surface Waves. Angelo Angelini, Elsie Barakat, Peter Munzert, Luca Boarino, Natascia De Leo, Supplementary Information for Focusing and Extraction of Light mediated by Bloch Surface Waves Angelo Angelini, Elsie Barakat, Peter Munzert, Luca Boarino, Natascia De Leo, Emanuele Enrico, Fabrizio Giorgis,

More information

APPLICATIONS FOR TELECENTRIC LIGHTING

APPLICATIONS FOR TELECENTRIC LIGHTING APPLICATIONS FOR TELECENTRIC LIGHTING Telecentric lenses used in combination with telecentric lighting provide the most accurate results for measurement of object shapes and geometries. They make attributes

More information

Fiber Optic Communications

Fiber Optic Communications Fiber Optic Communications ( Chapter 2: Optics Review ) presented by Prof. Kwang-Chun Ho 1 Section 2.4: Numerical Aperture Consider an optical receiver: where the diameter of photodetector surface area

More information

PHYS 202 OUTLINE FOR PART III LIGHT & OPTICS

PHYS 202 OUTLINE FOR PART III LIGHT & OPTICS PHYS 202 OUTLINE FOR PART III LIGHT & OPTICS Electromagnetic Waves A. Electromagnetic waves S-23,24 1. speed of waves = 1/( o o ) ½ = 3 x 10 8 m/s = c 2. waves and frequency: the spectrum (a) radio red

More information

Premier & Acculase Modulatable Laser Diode Modules

Premier & Acculase Modulatable Laser Diode Modules Premier & Acculase Modulatable Laser Diode Modules Premier & Acculase Range. The Premier & Acculase laser diode modules represent the highest level of optical and electrical performance at an economical

More information

A novel tunable diode laser using volume holographic gratings

A novel tunable diode laser using volume holographic gratings A novel tunable diode laser using volume holographic gratings Christophe Moser *, Lawrence Ho and Frank Havermeyer Ondax, Inc. 85 E. Duarte Road, Monrovia, CA 9116, USA ABSTRACT We have developed a self-aligned

More information

Parallel Mode Confocal System for Wafer Bump Inspection

Parallel Mode Confocal System for Wafer Bump Inspection Parallel Mode Confocal System for Wafer Bump Inspection ECEN5616 Class Project 1 Gao Wenliang wen-liang_gao@agilent.com 1. Introduction In this paper, A parallel-mode High-speed Line-scanning confocal

More information

Chapter 17: Wave Optics. What is Light? The Models of Light 1/11/13

Chapter 17: Wave Optics. What is Light? The Models of Light 1/11/13 Chapter 17: Wave Optics Key Terms Wave model Ray model Diffraction Refraction Fringe spacing Diffraction grating Thin-film interference What is Light? Light is the chameleon of the physical world. Under

More information

PHY 431 Homework Set #5 Due Nov. 20 at the start of class

PHY 431 Homework Set #5 Due Nov. 20 at the start of class PHY 431 Homework Set #5 Due Nov. 0 at the start of class 1) Newton s rings (10%) The radius of curvature of the convex surface of a plano-convex lens is 30 cm. The lens is placed with its convex side down

More information

Optical Components - Scanning Lenses

Optical Components - Scanning Lenses Optical Components Scanning Lenses Scanning Lenses (Ftheta) Product Information Figure 1: Scanning Lenses A scanning (Ftheta) lens supplies an image in accordance with the socalled Ftheta condition (y

More information

plasmonic nanoblock pair

plasmonic nanoblock pair Nanostructured potential of optical trapping using a plasmonic nanoblock pair Yoshito Tanaka, Shogo Kaneda and Keiji Sasaki* Research Institute for Electronic Science, Hokkaido University, Sapporo 1-2,

More information

MicroSpot FOCUSING OBJECTIVES

MicroSpot FOCUSING OBJECTIVES OFR P R E C I S I O N O P T I C A L P R O D U C T S MicroSpot FOCUSING OBJECTIVES APPLICATIONS Micromachining Microlithography Laser scribing Photoablation MAJOR FEATURES For UV excimer & high-power YAG

More information

Kit for building your own THz Time-Domain Spectrometer

Kit for building your own THz Time-Domain Spectrometer Kit for building your own THz Time-Domain Spectrometer 16/06/2016 1 Table of contents 0. Parts for the THz Kit... 3 1. Delay line... 4 2. Pulse generator and lock-in detector... 5 3. THz antennas... 6

More information

Supplementary Materials

Supplementary Materials Supplementary Materials In the supplementary materials of this paper we discuss some practical consideration for alignment of optical components to help unexperienced users to achieve a high performance

More information

Polarization Experiments Using Jones Calculus

Polarization Experiments Using Jones Calculus Polarization Experiments Using Jones Calculus Reference http://chaos.swarthmore.edu/courses/physics50_2008/p50_optics/04_polariz_matrices.pdf Theory In Jones calculus, the polarization state of light is

More information

BEAMAGE KEY FEATURES AVAILABLE MODELS. CMOS Beam Profiling Cameras

BEAMAGE KEY FEATURES AVAILABLE MODELS. CMOS Beam Profiling Cameras BEAM DIAGNOS TICS Beam Profiling Cameras KEY FEATURES SPECIAL PRODUCTS OEM DETECTORS THZ DETECTORS PHOTO DETECTORS HIGH POWER SOLUTIONS POWER DETECTORS ENERGY DETECTORS MONITORS AVAILABLE MODELS Beamage-3.0

More information

Lab Report 3: Speckle Interferometry LIN PEI-YING, BAIG JOVERIA

Lab Report 3: Speckle Interferometry LIN PEI-YING, BAIG JOVERIA Lab Report 3: Speckle Interferometry LIN PEI-YING, BAIG JOVERIA Abstract: Speckle interferometry (SI) has become a complete technique over the past couple of years and is widely used in many branches of

More information

Beam Shaping and Simultaneous Exposure by Diffractive Optical Element in Laser Plastic Welding

Beam Shaping and Simultaneous Exposure by Diffractive Optical Element in Laser Plastic Welding Beam Shaping and Simultaneous Exposure by Diffractive Optical Element in Laser Plastic Welding AKL`12 9th May 2012 Dr. Daniel Vogler Page 1 Motivation: Quality and flexibility diffractive spot shaping

More information

OPERATING MANUAL. 100 MHz CENTER FREQUENCY OFF AXIS ACOUSTO-OPTIC BEAM DEFLECTOR MODEL NUMBER: DEG-.51 DOCUMENT NUMBER: 51A12229A

OPERATING MANUAL. 100 MHz CENTER FREQUENCY OFF AXIS ACOUSTO-OPTIC BEAM DEFLECTOR MODEL NUMBER: DEG-.51 DOCUMENT NUMBER: 51A12229A OPERATING MANUAL 100 MHz CENTER FREQUENCY OFF AXIS ACOUSTO-OPTIC BEAM DEFLECTOR MODEL NUMBER: DOCUMENT NUMBER: 51A12229A Document approved for release: W Seale Date: 8/18/06 US OFFICE: NEOS Technologies,

More information

FRAUNHOFER AND FRESNEL DIFFRACTION IN ONE DIMENSION

FRAUNHOFER AND FRESNEL DIFFRACTION IN ONE DIMENSION FRAUNHOFER AND FRESNEL DIFFRACTION IN ONE DIMENSION Revised November 15, 2017 INTRODUCTION The simplest and most commonly described examples of diffraction and interference from two-dimensional apertures

More information

Exercise 8: Interference and diffraction

Exercise 8: Interference and diffraction Physics 223 Name: Exercise 8: Interference and diffraction 1. In a two-slit Young s interference experiment, the aperture (the mask with the two slits) to screen distance is 2.0 m, and a red light of wavelength

More information

Vixar High Power Array Technology

Vixar High Power Array Technology Vixar High Power Array Technology I. Introduction VCSELs arrays emitting power ranging from 50mW to 10W have emerged as an important technology for applications within the consumer, industrial, automotive

More information

Diode Collimator Assembly Datasheet

Diode Collimator Assembly Datasheet Diode Collimator Assembly Datasheet Diode Collimator Assembly Global Laser s DCA (Diode Collimator Assembly) provides a low cost high quality OEM solution to manufactures looking for a compact assembly

More information

Exam 4. Name: Class: Date: Multiple Choice Identify the choice that best completes the statement or answers the question.

Exam 4. Name: Class: Date: Multiple Choice Identify the choice that best completes the statement or answers the question. Name: Class: Date: Exam 4 Multiple Choice Identify the choice that best completes the statement or answers the question. 1. Mirages are a result of which physical phenomena a. interference c. reflection

More information

Effect of Beam Size on Photodiode Saturation

Effect of Beam Size on Photodiode Saturation Effect of Beam Size on Photodiode Saturation Experiments were conducted to demonstrate a change in the saturation point for a FDS1010 silicon photodiode as a function of beam diameter. The saturation point

More information

COLOUR INSPECTION, INFRARED AND UV

COLOUR INSPECTION, INFRARED AND UV COLOUR INSPECTION, INFRARED AND UV TIPS, SPECIAL FEATURES, REQUIREMENTS LARS FERMUM, CHIEF INSTRUCTOR, STEMMER IMAGING THE PROPERTIES OF LIGHT Light is characterized by specifying the wavelength, amplitude

More information

Radial Polarization Converter With LC Driver USER MANUAL

Radial Polarization Converter With LC Driver USER MANUAL ARCoptix Radial Polarization Converter With LC Driver USER MANUAL Arcoptix S.A Ch. Trois-portes 18 2000 Neuchâtel Switzerland Mail: info@arcoptix.com Tel: ++41 32 731 04 66 Principle of the radial polarization

More information

Optical Components for Laser Applications. Günter Toesko - Laserseminar BLZ im Dezember

Optical Components for Laser Applications. Günter Toesko - Laserseminar BLZ im Dezember Günter Toesko - Laserseminar BLZ im Dezember 2009 1 Aberrations An optical aberration is a distortion in the image formed by an optical system compared to the original. It can arise for a number of reasons

More information

End-of-Chapter Exercises

End-of-Chapter Exercises End-of-Chapter Exercises Exercises 1 12 are conceptual questions designed to see whether you understand the main concepts in the chapter. 1. Red laser light shines on a double slit, creating a pattern

More information

Applying of refractive beam shapers of circular symmetry to generate non-circular shapes of homogenized laser beams

Applying of refractive beam shapers of circular symmetry to generate non-circular shapes of homogenized laser beams - 1 - Applying of refractive beam shapers of circular symmetry to generate non-circular shapes of homogenized laser beams Alexander Laskin a, Vadim Laskin b a MolTech GmbH, Rudower Chaussee 29-31, 12489

More information

AP B Webreview ch 24 diffraction and interference

AP B Webreview ch 24 diffraction and interference Name: Class: _ Date: _ AP B Webreview ch 24 diffraction and interference Multiple Choice Identify the choice that best completes the statement or answers the question.. In order to produce a sustained

More information

Optical Coherence: Recreation of the Experiment of Thompson and Wolf

Optical Coherence: Recreation of the Experiment of Thompson and Wolf Optical Coherence: Recreation of the Experiment of Thompson and Wolf David Collins Senior project Department of Physics, California Polytechnic State University San Luis Obispo June 2010 Abstract The purpose

More information

Assembly and Experimental Characterization of Fiber Collimators for Low Loss Coupling

Assembly and Experimental Characterization of Fiber Collimators for Low Loss Coupling Assembly and Experimental Characterization of Fiber Collimators for Low Loss Coupling Ruby Raheem Dept. of Physics, Heriot Watt University, Edinburgh, Scotland EH14 4AS, UK ABSTRACT The repeatability of

More information

Applications of Optics

Applications of Optics Nicholas J. Giordano www.cengage.com/physics/giordano Chapter 26 Applications of Optics Marilyn Akins, PhD Broome Community College Applications of Optics Many devices are based on the principles of optics

More information

Physics 431 Final Exam Examples (3:00-5:00 pm 12/16/2009) TIME ALLOTTED: 120 MINUTES Name: Signature:

Physics 431 Final Exam Examples (3:00-5:00 pm 12/16/2009) TIME ALLOTTED: 120 MINUTES Name: Signature: Physics 431 Final Exam Examples (3:00-5:00 pm 12/16/2009) TIME ALLOTTED: 120 MINUTES Name: PID: Signature: CLOSED BOOK. TWO 8 1/2 X 11 SHEET OF NOTES (double sided is allowed), AND SCIENTIFIC POCKET CALCULATOR

More information

X-ray generation by femtosecond laser pulses and its application to soft X-ray imaging microscope

X-ray generation by femtosecond laser pulses and its application to soft X-ray imaging microscope X-ray generation by femtosecond laser pulses and its application to soft X-ray imaging microscope Kenichi Ikeda 1, Hideyuki Kotaki 1 ' 2 and Kazuhisa Nakajima 1 ' 2 ' 3 1 Graduate University for Advanced

More information

Imaging Systems Laboratory II. Laboratory 8: The Michelson Interferometer / Diffraction April 30 & May 02, 2002

Imaging Systems Laboratory II. Laboratory 8: The Michelson Interferometer / Diffraction April 30 & May 02, 2002 1051-232 Imaging Systems Laboratory II Laboratory 8: The Michelson Interferometer / Diffraction April 30 & May 02, 2002 Abstract. In the last lab, you saw that coherent light from two different locations

More information

Instructions LASNIX Polarization Sensors Models 601, 605, option H

Instructions LASNIX Polarization Sensors Models 601, 605, option H Instructions LASNIX Polarization Sensors Models 601, 605, option H 1. HANDLING. LASNIX polarization sensors operate on the principle of a rotating linear polarizer. The polarizer element is a very thin

More information

Properties of Structured Light

Properties of Structured Light Properties of Structured Light Gaussian Beams Structured light sources using lasers as the illumination source are governed by theories of Gaussian beams. Unlike incoherent sources, coherent laser sources

More information

Varilite Datasheet. Thread Mountable Laser Diode Module

Varilite Datasheet. Thread Mountable Laser Diode Module Varilite Datasheet Thread Mountable Laser Diode Module Varilite The Varilite range combines all the features of Global Lasers Premier range with the addition of a threaded barrel to simplify mounting and

More information

Photonics West Contact us for a Stock or Custom Quote Today! Edmund Optics BROCHURE

Photonics West Contact us for a Stock or Custom Quote Today!   Edmund Optics BROCHURE Edmund Optics BROHURE Photonics West 2017 Product Highlights Beam Expanders Off-xis Parabolic Mirrors Right ngle Prisms ontact us for a Stock or ustom Quote Today! US: +1-856-547-3488 EUROPE: +44 (0) 1904

More information

Akinori Mitani and Geoff Weiner BGGN 266 Spring 2013 Non-linear optics final report. Introduction and Background

Akinori Mitani and Geoff Weiner BGGN 266 Spring 2013 Non-linear optics final report. Introduction and Background Akinori Mitani and Geoff Weiner BGGN 266 Spring 2013 Non-linear optics final report Introduction and Background Two-photon microscopy is a type of fluorescence microscopy using two-photon excitation. It

More information

Simulation and realization of a focus shifting unit using a tunable lens for 3D laser material processing

Simulation and realization of a focus shifting unit using a tunable lens for 3D laser material processing Available online at www.sciencedirect.com Physics Procedia 41 (2013 ) 441 447 Lasers in Manufacturing Conference 2013 Simulation and realization of a focus shifting unit using a tunable lens for 3D laser

More information

LaserBeam ProfilingSolutions. IRLaserBeam Profiler

LaserBeam ProfilingSolutions. IRLaserBeam Profiler LaserBeam ProfilingSolutions IRLaserBeam Profiler TABLE OF CONTENTS PRODUCT DESCRIPTION LASERDEC CL200 TECHNICAL DATA DIMENSIONS LASERDEC CL500 TECHNICAL DATA DIMENSIONS LASERDEC CR200 TECHNICAL DATA DIMENSIONS

More information

White Paper: Modifying Laser Beams No Way Around It, So Here s How

White Paper: Modifying Laser Beams No Way Around It, So Here s How White Paper: Modifying Laser Beams No Way Around It, So Here s How By John McCauley, Product Specialist, Ophir Photonics There are many applications for lasers in the world today with even more on the

More information

Diffractive Axicon application note

Diffractive Axicon application note Diffractive Axicon application note. Introduction 2. General definition 3. General specifications of Diffractive Axicons 4. Typical applications 5. Advantages of the Diffractive Axicon 6. Principle of

More information

CHAPTER 5 FINE-TUNING OF AN ECDL WITH AN INTRACAVITY LIQUID CRYSTAL ELEMENT

CHAPTER 5 FINE-TUNING OF AN ECDL WITH AN INTRACAVITY LIQUID CRYSTAL ELEMENT CHAPTER 5 FINE-TUNING OF AN ECDL WITH AN INTRACAVITY LIQUID CRYSTAL ELEMENT In this chapter, the experimental results for fine-tuning of the laser wavelength with an intracavity liquid crystal element

More information

Power. Warranty. 30 <1.5 <3% Near TEM ~4.0 one year. 50 <1.5 <5% Near TEM ~4.0 one year

Power. Warranty. 30 <1.5 <3% Near TEM ~4.0 one year. 50 <1.5 <5% Near TEM ~4.0 one year DL CW Blue Violet Laser, 405nm 405 nm Operating longitudinal mode Several Applications: DNA Sequencing Spectrum analysis Optical Instrument Flow Cytometry Interference Measurements Laser lighting show

More information

IMAGE SENSOR SOLUTIONS. KAC-96-1/5" Lens Kit. KODAK KAC-96-1/5" Lens Kit. for use with the KODAK CMOS Image Sensors. November 2004 Revision 2

IMAGE SENSOR SOLUTIONS. KAC-96-1/5 Lens Kit. KODAK KAC-96-1/5 Lens Kit. for use with the KODAK CMOS Image Sensors. November 2004 Revision 2 KODAK for use with the KODAK CMOS Image Sensors November 2004 Revision 2 1.1 Introduction Choosing the right lens is a critical aspect of designing an imaging system. Typically the trade off between image

More information

Single-photon excitation of morphology dependent resonance

Single-photon excitation of morphology dependent resonance Single-photon excitation of morphology dependent resonance 3.1 Introduction The examination of morphology dependent resonance (MDR) has been of considerable importance to many fields in optical science.

More information

Table of Content. Fiber-Coupled LED s Light-Guide-Coupled LED s LED Collimator Sources Low-cost LED Spot Lights...

Table of Content. Fiber-Coupled LED s Light-Guide-Coupled LED s LED Collimator Sources Low-cost LED Spot Lights... LIGHT SOURCES Table of Content Fiber-Coupled s... 40 -Guide-Coupled s... 41 Collimator... 42 Low-cost Spot s... 43 Precision Spot s... 45 Spectrum Synthesizing ( Cubic S )... 46 Spectrometers 39 sources

More information

Technical Notes. Introduction. Optical Properties. Issue 6 July Figure 1. Specular Reflection:

Technical Notes. Introduction. Optical Properties. Issue 6 July Figure 1. Specular Reflection: Technical Notes This Technical Note introduces basic concepts in optical design for low power off-grid lighting products and suggests ways to improve optical efficiency. It is intended for manufacturers,

More information

Bandpass Interference Filters

Bandpass Interference Filters Precise control of center wavelength and bandpass shape Wide selection of stock wavelengths from 250 nm-1550 nm Selection of bandwidths Available in 1/2 and 1 sizes High peak transmission values Excellent

More information

Vanishing Core Fiber Spot Size Converter Interconnect (Polarizing or Polarization Maintaining)

Vanishing Core Fiber Spot Size Converter Interconnect (Polarizing or Polarization Maintaining) Vanishing Core Fiber Spot Size Converter Interconnect (Polarizing or Polarization Maintaining) The Go!Foton Interconnect (Go!Foton FSSC) is an in-fiber, spot size converting interconnect for convenient

More information

Supplementary Figure 1. GO thin film thickness characterization. The thickness of the prepared GO thin

Supplementary Figure 1. GO thin film thickness characterization. The thickness of the prepared GO thin Supplementary Figure 1. GO thin film thickness characterization. The thickness of the prepared GO thin film is characterized by using an optical profiler (Bruker ContourGT InMotion). Inset: 3D optical

More information

EE119 Introduction to Optical Engineering Spring 2002 Final Exam. Name:

EE119 Introduction to Optical Engineering Spring 2002 Final Exam. Name: EE119 Introduction to Optical Engineering Spring 2002 Final Exam Name: SID: CLOSED BOOK. FOUR 8 1/2 X 11 SHEETS OF NOTES, AND SCIENTIFIC POCKET CALCULATOR PERMITTED. TIME ALLOTTED: 180 MINUTES Fundamental

More information

Exp No.(8) Fourier optics Optical filtering

Exp No.(8) Fourier optics Optical filtering Exp No.(8) Fourier optics Optical filtering Fig. 1a: Experimental set-up for Fourier optics (4f set-up). Related topics: Fourier transforms, lenses, Fraunhofer diffraction, index of refraction, Huygens

More information

Chapter 18 Optical Elements

Chapter 18 Optical Elements Chapter 18 Optical Elements GOALS When you have mastered the content of this chapter, you will be able to achieve the following goals: Definitions Define each of the following terms and use it in an operational

More information

Optoliner NV. Calibration Standard for Sighting & Imaging Devices West San Bernardino Road West Covina, California 91790

Optoliner NV. Calibration Standard for Sighting & Imaging Devices West San Bernardino Road West Covina, California 91790 Calibration Standard for Sighting & Imaging Devices 2223 West San Bernardino Road West Covina, California 91790 Phone: (626) 962-5181 Fax: (626) 962-5188 www.davidsonoptronics.com sales@davidsonoptronics.com

More information

Gentec Electro-Optics, Inc

Gentec Electro-Optics, Inc Gentec Electro-Optics, Inc. 2013. Accessories for Beam Diagnostics Revision 1.2 2 WARRANTY The Gentec-EO accessories for beam diagnostics carry a one-year warranty (from date of shipment) against material

More information

A broadband achromatic metalens for focusing and imaging in the visible

A broadband achromatic metalens for focusing and imaging in the visible SUPPLEMENTARY INFORMATION Articles https://doi.org/10.1038/s41565-017-0034-6 In the format provided by the authors and unedited. A broadband achromatic metalens for focusing and imaging in the visible

More information

High Average Power, High Repetition Rate Side-Pumped Nd:YVO 4 Slab Laser

High Average Power, High Repetition Rate Side-Pumped Nd:YVO 4 Slab Laser High Average Power, High Repetition Rate Side-Pumped Nd:YVO Slab Laser Kevin J. Snell and Dicky Lee Q-Peak Incorporated 135 South Rd., Bedford, MA 173 (71) 75-9535 FAX (71) 75-97 e-mail: ksnell@qpeak.com,

More information

BLUE SKY RESEARCH BLUE

BLUE SKY RESEARCH BLUE BLUE SKY RESEARCH Blue Sky Research is a company dedicated to providing the best possible balance of performance, value and quality. We have fielded over 1 million lasers since our inception in 1989, and

More information

Optical Isolator Tutorial (Page 1 of 2) νlh, where ν, L, and H are as defined below. ν: the Verdet Constant, a property of the

Optical Isolator Tutorial (Page 1 of 2) νlh, where ν, L, and H are as defined below. ν: the Verdet Constant, a property of the Aspheric Optical Isolator Tutorial (Page 1 of 2) Function An optical isolator is a passive magneto-optic device that only allows light to travel in one direction. Isolators are used to protect a source

More information

Z-LASER Optoelektronik GmbH Stemmer 3d Technologietag Useful information on Z-Lasers for Vision

Z-LASER Optoelektronik GmbH Stemmer 3d Technologietag Useful information on Z-Lasers for Vision Z-LASER Optoelektronik GmbH Stemmer 3d Technologietag - 24.2.2011 Useful information on Z-Lasers for Vision The Company Core Competences How to Build a Z-LASER Electronics and Modulation Wavelength and

More information