DAZZLE ACCENT LIGHTING SYSTEM
|
|
- Amber Fleming
- 6 years ago
- Views:
Transcription
1 DAZZLE ACCENT LIGHTING SYSTEM SAFETY & WARNINGS 1. Install in accordance with national and local electrical code regulations. 2. This product is intended to be installed and serviced by a qualified, licensed electrician. 3. Do not submerge, or install within 5 feet of a swimming pool. 4. Do not modify or disassemble this product beyond instructions or this warranty will be void. 5. Not for use in submersible applications. QUICK SPECS / MODELS DI-IL-TAPE-BLK-* DI-IL-TAPE-WHT-* Input 24VDC Constant Voltage IP65 24VDC HANDLE PRODUCT WITH CARE! Power Max. Run Ambient Temp.29W per foot 130 feet per controller output -4 ~ 122 F (-20 ~ 50 C) * Indicates length Do not install product in environment outside listed temperature. DO NOT POWER STRIP LIGHT WHILE ATTACHED TO SPOOL OR TIGHTLY COILED. DO NOT BEND LED STRIP LIGHT ON A HORIZONTAL PLANE. DO NOT FOLD, CREASE, OR TWIST LED STRIP LIGHT. DO NOT COVER STRIP LIGHT WITH ANY MATERIALS. ADDITIONAL ACCESSORIES Channel Cover DI-IL-COVER* Mounting Channel DI-IL-BASE* * Indicates color 1 OF 6 IG
2 MEETS DMX512(1990) LED Controller MODE SET UP DOWN power signal INSTALLATION 1 TURN POWER OFF AT CIRCUIT BREAKER b DAZZLE ACCENT LIGHTING SYSTEM MITER CUTS When mitering the Channel and Cover, cut at an angle. SHOCK HAZARD! May result in serious injury or death. Turn power OFF at circuit breaker prior to installalation. 2 DETERMINE LOCATION TO INSTALL COMPONENTS 4 PLACE DAZZLE ACCENT CHANNEL NOT FOR USE IN SUBMERSIBLE APPLICATIONS, OR WITHIN 5 FEET OF A SWIMMING POOL. Refer to SYSTEM DIAGRAMS a 3M ADHESIVE BACK Peel backing from 3M adhesive strip on back of channel. 1) 200W Driver* 2) Color Controller 3) STRIP, CHANNEL & COVER *Class 2 option available. 3 CREATE CHANNEL AND COVER LENGTHS a STRAIGHT CUTS Using a saw, cut the Channel and Cover to length. b PLACE CHANNEL Allowing 3M adhesive to hold the channel in place, use screws to fasten channel to surface.* *Note: Ensure that plenty of space is left between channels when installing around corners. Pinching, or bending Strip Light and/or extension cables may result in damage to the system. 2 OF 6 IG
3 INSTALLATION (CONT.) 5 CREATE STRIP LIGHT LENGTHS Connect ends of Strip Light together until desired length is reached.* You may mix and match different lengths of Strip Light. Ensure extensions and connector cables are measured and placed optimally throughout the installation. *Note: Do not cut or modify Strip Light. b DAZZLE ACCENT LIGHTING SYSTEM SIDE CHANNELS The lower areas on either side of the channel may be used to place and hide additional wires used for installation. c PLACE COVER AND END CAP Snap covers onto channel. Insert end cap into last channel in system. a 6 COMPLETE STRIP LIGHT AND CHANNEL INSTALLATION PLACE STRIP LIGHT WITHIN RAISED CHANNEL From one end, place Strip Light within raised channel. 7 8 ATTACH CONTROLLER AND DRIVER Verify a compatible driver is installed. Utilize applicable wiring when installing outdoors. (Use of wet location rated junction box recommended) REVIEW SYSTEM Ensure all polarities are correct and connections are secure. 9 TURN POWER ON AT CIRCUIT BREAKER 3 OF 6 IG
4 DAZZLE ACCENT LIGHTING SYSTEM SYSTEM DIAGRAM 120 VAC WALL OUTLET DAZZLE ACCENT 200 WATT DRIVER DI-IL-TRANS200 DAZZLE ACCENT COLOR CONTROLLER DI-IL-CONTROL1 24 VDC DAZZLE ACCENT EXTENSION CABLES DI-IL-EXT3 DI-IL-EXT10 DI-IL-EXT25 DI-IL-EXT100 DAZZLE ACCENT STRIP LIGHT, CHANNEL, AND COVER Some LEDs are not functional Ensure strip light has not been bent excessively, which could damage circuitry. Ensure strip light has not been submerged in any liquid for any amount of time. Lights are flickering Lights are turning on/off repeatedly Check for loose connections. Ensure driver is not overloaded. An overloaded driver will trip the internal auto-reset (of driver) repeatedly, turning the system on/off. 4 OF 6 IG
5 DAZZLE ACCENT LIGHTING SYSTEM SYSTEM OPERATION DAZZLE ACCENT COLOR CONTROLLER LED Controller 01 WARM WHITE MODE SET UP DOWN power signal MODE SET UP DOWN MEETS DMX512(1990) MODE Short press: Cycle through (33) available modes. SET Short press: Edit current scene.* UP Short press: Cycle mode up by one. DOWN Short press: Cycle mode down by one. Onceeditiscomplete,short press to save the current setting. *When editing single color scene, short press to increase the brightness. *When editing single color scene, this will decrease the brightness. DAZZLE ACCENT REMOTE CONTROL *When editing Holiday, or Celebration scenes, short press to increase the speed of the scene. *When editing Holiday, or Celebration scenes, short press to decrease the speed of the scene. Turn power On/Off POWER PAUSE Stops current Holiday, or Celebration mode Short press: Cycle mode up by one. MODE + MODE - Short press: Cycle mode down by one. Hold to increase the speed of the current scene. SPEED + SPEED - Hold to decrease the speed of the current scene. Hold to increase the brightness of the current static color. BRT + BRT - Hold to decrease the brightness of the current static color. 5 OF 6 IG
6 DAZZLE ACCENT LIGHTING SYSTEM COLOR CONTROL SCENES STATIC HOLIDAY SCENES CELEBRATION SCENES 1. Warm White 12. Red, Green Gradual 24. Purple, White Gradual 2. Soft White 13. Red, Green Jump 25. Red Flick 3. Pure White 14. Green, Warm White, Red, Warm White Gradual 26. Gold, Blue Jump 4. Gold 15. Pink, Red Smooth 27. Purple, Yellow Jump 5. Red 16. Pink, Warm White, Red, Warm White Gradual 28. Maroon Gradual 6. Orange 17. Green, White Gradual 29. Green, Gold Jump 7. Yellow 18. Purple, Indigo, Gold Gradual 30. Burnt Orange Gradual 8. Green 19. Red, Pure White, Blue Smooth 31. Red, Pure White Jump 9. Blue 20. Red, Pure White, Blue Jump 32. Yellow, Pure White Jump 10. Indigo 21. Red, Pure White, Blue Gradual 33. Blue, Pure White Jump 11. Purple 22. Orange, Pure White Jump 23. Orange Gradual Toll Free: Fax: Elemental LED Inc. All rights reserved. Specifications are subject to change without notice. 6 OF 6 IG
diode led DAZZLE ACCENT LIGHTING SYSTEM POWERED BY INCEPTION LIGHTING TECHNOLOGY IP65 24VDC SPECIFICATIONS CHANNEL COVER AVAILABLE IN:
DAZZLE ACCENT LIGHTING SYSTEM SPECIFICATION SHEET ITEM # 24VDC RGB CHANNEL COVER AVAILABLE IN: STRIP COLOR LENGTH LUMENS¹ DI-IL-TAPE-BLK-0.5 Black 20 inches 84 DI-IL-TAPE-BLK-1.5 Black 59 inches 252 DI-IL-TAPE-BLK-5.0
More informationProject: Client: Part #: NEON -P FLT HB 24VDC WHT lc con cab. Date: Qty:
LED Neon Light Flat Part #: NEON -P FLT HB 24VDC WHT lc con cab LED Neon Light Flat SPECIFICATION 27.5 19.5 HORIZONTAL BEND 46.5 CST Standard Snap Connector shown. Dimensions in millimeters See connections
More informationLED Neon Light Round
LED Neon Light Round Part #: NEON -P RND HB 24VDC WHT lc con cab LED Neon Light Round SPECIFICATION 36 21.5 19.5 HORIZONTAL BEND 46.5 CST Length CST Custom Length 3 cuttable every 3.25 Operating Voltage
More informationSUPERPLANE 2.5 INSTALLATION INSTRUCTIONS WALL/SURFACE BACK MOUNT. A nd Avenue, Unit 1 Oakland,
INSTALLATION INSTRUCTIONS SUPERPLANE 2.5 WALL/SURFACE BACK MOUNT A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP2.5 - Safety & Warnings! 1. Read all instructions.
More informationINSTALLATION INSTRUCTIONS SUPERPLANE 4 WALL MOUNT. A nd Avenue, Unit 1 Oakland, CA P E W alwusa.
INSTALLATION INSTRUCTIONS SUPERPLANE 4 WALL MOUNT A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP4 - Safety & Warnings! 1. Read all instructions. 2. Install
More informationProject: Client: Part #: NEON -P ARC 24VDC WHT lc con cab. Date: Qty: Length CST Custom Length cuttable every 2.81 Operating Voltage (ov)
LED Neon Light Arch LED Neon Light Arch Length CST Custom Length cuttable every 2.81 Operating Voltage (ov) 24V DC Finish (fin) WHT White 2700K Incandescent White 3000K Warm White 3500K Sand White Light
More informationLED Neon Light Arch RGB
LED Neon Light Arch RGB Part #: NEON -P ARC 24VDC WHT RGB con cab LED Neon Light Arch RGB Length CST Custom Length cuttable every 2.81 Operating Voltage (ov) 24V DC Finish (fin) WHT White SPECIFICATION
More informationLED Neon Light Flat RGBW
LED Neon Light Flat RGBW Part #: NEON -P FLT HB 24VDC WHT RGBW con cab LED Neon Light Flat RGBW Length CST Custom Length 2 cuttable every 3.25 SPECIFICATION Operating Voltage (ov) 24V DC Finish (fin) WHT
More informationSUPERPLANE TM 4 RECESSED SP4R
Oakland, INSTALLATION INSTRUCTIONS SUPERPLANE TM RECESSED SPR TGrid ATZ Slot n A 1035 22nd Avenue, Unit 1 CA 606 P 510.8.2530 E TalkToUs@alwusa.com W alwusa.com SPR - Safety & Warnings! 1. Read all instructions.
More informationdiode led 24VDC COMMERCIAL GRADE SPECIFICATION SHEET RECEIVE A UL LISTED DRIVER WHEN ORDERING THE LO-PRO JUNCTION BOX & DRIVER COMBO ON PAGE 2.
diode led a division of elemental LED 24VDC COMMERCIAL GRADE 0-10V LED DIMMABLE DRIVER 24VDC WET LOCATION DIMMABLE SPECIFICATION SHEET OVERVIEW 24VDC Commercial Grade 0-10V Dimmable LED Drivers are essential
More informationFLEXDC INSTALLATION GUIDE
Please read entire guide prior to starting installation. NOTES 1. IP40 and lower tape must be installed indoors only. 2. Installation must be carried out by a licensed electrician & executed in accordance
More informationProduct Description. Yes 24V DC 72W -120W 120º. Between LEDs: 0.66in / 16mm. Width: 0.75in / 19mm Between LEDs: 0.81in / 20mm
RGBW COLOR CHANGING LED STRIP LIGHT Product Description Solid Apollo s RGBW LED Strip Lights are a combination of our normal RGB color-changing and White color 5050 LED chips. With this RGBW Strip, billions
More informationProduct Description. Quick Spec. Fully Dimmable: Voltage: Total Wattage: Beam Angle: Yes 24V DC 72W 120º
RGBW WATERPROOF COLOR CHANGING LED STRIP LIGHT Product Description Solid Apollo s Waterproof RGBW LED Strip Lights are a combination of our normal RGB color-changing and White color chips in one 5050 LED.
More informationPRODUCT DATA SHEET. ColorBright Color Changing. RGB 300 Series. Year Warranty.
PRODUCT DATA SHEET ColorBright Color Changing RGB 300 Series 5 Year Warranty www.flexfireleds.com Description The ColorBright Color Changing 300 LED strip light has double the amount of bright LEDs than
More informationInstallation Instructions for TruLine 1.6A 24VDC. Section One: Basic Configuration Options
Doc # 902-TL1.6A_07 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com 2016 PureEdge Lighting. All Rights Reserved. Installation Instructions
More informationA-dec 574L and 575L Dental Lights on a Cabinet or Wall INSTALLATION GUIDE
A-dec 574L and 575L Dental Lights on a Cabinet or Wall INSTALLATION GUIDE A-dec 574L Dental Light Mounted on an A-dec Inspire TM 59 Central Console Before You Begin. Turn off the power to the system before
More informationInstallation Instructions For TruLine 1.6A 24VDC
2014 Pure Lighting. All Rights Reserved. Installation Instructions For TruLine 1.6A 24VDC INS# 902-TL1.6A-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationPHOTO FRAME STRING LIGHTBOXES
PFL-500CD PHOTO FRAME STRING LIGHTBOXES Candlenut Distressed Wood Frame USER MANUAL NEED HELP? Call our help line 1-866-765-3686 or visit us at: www.polaroidlightboxes.com Polaroid, Polaroid & Pixel, Polaroid
More informationTRANSFORMER HD-HAMPTON HAMPTONBAY.COM
Item #1001 510 115 Model DIY-600PS USE AND CARE GUIDE TRANSFORMER Questions, problems, missing parts? Before returning to the store, call HamptonBay Customer Service 8 a.m. - 7 p.m., EST, Monday Friday,
More informationInstallation Instructions for TruLine 1A Center Feed Power Channel Connector
IMPORTANT INFORMATION - This instruction must be used concurrently with other TruLine A BIY installation instructions. - This product is wall or ceiling mount. - This instruction shows a typical installation.
More informationLED RETROFIT INSTALLATION
QUICK INSTRUCTIONS 1 2 3 4 5 6 Once the original fixture components have been removed to satisfy rebate requirements the Raffino LR Series retrofit kit is ready to be instal. At a minimum the original
More informationATTRIBUTE SPECIFICATION SHEET 12VDC 24VDC OVERVIEW FEATURES & BENEFITS APPROVED LED LUMINAIRES COLOR CONTROLLER
DY LOCATION COLO-CHANIN 12VDC 24VDC ATTIUTE COLO CONTOLLE SPECIFICATION SHEET V ATTIUTE eceiver DI-ATT--EC 9/32 in. : 12-24VDC (7mm) OUTPUT: 12-24VDC 4CH X 5A LEANIN KEY POE OVEVIE The ATTIUTE Color Controller
More informationROUND LIGHTPLANE 1 3D FLUSH
INSTALLATION INSTRUCTIONS ROUND LIGHTPLANE 1 3D FLUSH RLP1/3D/F Flush Mount Configuration LED A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings!
More informationCOOLEDGE TILE GEN2 INTERIOR-TUNABLE WHITE INSTALLATION MANUAL
5 YEAR SYSTEM WARRANTY 5 YEAR SYSTEM WARRANTY COOLEDGE TILE GEN2 INTERIOR-TUNABLE WHITE INSTALLATION MANUAL Cutout TILE TILE Insulating Patches Jumper Cable T-Cable End Cap Cable Clamp Power Supply Control
More informationINSTALLATION INSTRUCTIONS Xenix Incandescent Series XN12, XN24, XN36, XN48
INSTALLATION INSTRUCTIONS Xenix Incandescent Series XN12, XN24, XN36, XN48 IMPORTANT SAFETY INSTRUCTIONS ---- CAUTION! --- READ THIS FIRST 11500 Melrose Avenue Franklin Park, Illinois 60131 Phone: 847-451-0700
More informationInstallation Instructions For Reveal
2017 Pure Lighting. All Rights Reserved. Installation Instructions For Reveal IS# 902-RV-24VDC-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1196 Fax: 773-883-6128 www.purelighting.com info@purelighting.com
More informationWaterproof RGB Pixel Control LED Neon Part Number: PLN-RGB-20
Waterproof RGB Pixel Control LED Neon Part Number: PLN-RGB-20 11235 West Bernardo Court, Suite 102 San Diego, CA 92127 888-880-1880 Fax: 707-281-0567 EnvironmentalLights.com RGB Pixel Control LED Neon
More informationINSTALLATION GUIDE. Yellow Jacket Oscillator. For help, call BIG-FANS or visit
INSTALLATION GUIDE Yellow Jacket Oscillator For help, call 1-877-BIG-FANS or visit www.bigassfans.com READ AND SAVE THESE INSTRUCTIONS WARNING AND CAUTION SYMBOL Indicates a hazard with a medium level
More informationYES 12 Charging Wall Cabinet for Mini-laptops
Built with Anthro-DNA Owner's Manual for YES 12 Charging Wall Cabinet for Mini-laptops Part # YESMLCGMPW Components at a Glance 7 1 9 8 2 4 5 11 6 10 3 Front of Cabinet (closed) 1. Locking front door to
More informationYes 20 Charging Wall Cabinet for Tablets
Built with Anthro-DNA Owner's Manual for Yes 20 Charging Wall Cabinet for Tablets Part # YESCABGMPW Components at a Glance 1 2 4 5 8 7 10 Front of Cabinet (closed) 1. Locking front door to User area. 2.
More informationO. S. WALKER MICROPROCESSOR CHUCK CONTROL MODEL MSB SERIES TABLE OF CONTENTS
O. S. WALKER MICROPROCESSOR CHUCK CONTROL MODEL MSB SERIES TABLE OF CONTENTS PAGE 1-3 OPERATING INSTRUCTIONS 4 DEMAG CYCLE STEPS 5 INSTALLATION INSTRUCTIONS 6 SPECIFICATIONS 7 & 8 DIMENSIONAL DIAGRAMS
More informationYes 20 Charging Wall Cabinet for Tablets
Built with Anthro-DNA Owner's Manual for Yes 20 Charging Wall Cabinet for Tablets Part # YESCABGMPW Components at a Glance 1 2 4 5 8 7 10 3 6 9 Front of Cabinet (closed) 1. Locking front door to User area.
More informationPSC-43X. Owner s Manual SEATED CALF RAISE
SEATED CALF RAISE Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each workout.
More informationStandard Halogen Light
Standard Halogen Light : Niche type protection index IP 68 underwater light for concrete or vinyl pools. Material: Body and Rim are made of UV resistance white ABS. Cable:.6 m H07RN-F cable with 2 x 4
More informationLW5 LB5 LW10 LB10 QUICKSTART GUIDE. Lyra Daylight LED Half x 1 Soft Light. Lyra Bi-Color LED Half x 1 Soft Light. Lyra Daylight LED 1x1 Soft Light
QUICKSTART GUIDE LW5 Lyra Daylight LED Half x 1 Soft Light LB5 Lyra Bi-Color LED Half x 1 Soft Light LW10 Lyra Daylight LED 1x1 Soft Light LB10 Lyra Bi-Color LED 1 x 1 Soft Light 2016 ikan Corporation.
More information4 Channel 4~20mA / 0~10VDC Analog DIN Fiber Link System
USER GUIDE RLH Industries, Inc. The leader in rugged fiber optic technology. U-026 2017A-0420 4 Channel 4~20mA / 0~10VDC Analog DIN Fiber Link System SYSTEM INSTALLATION INFORMATION Description The DIN
More informationSMART TOILET CONTROL
WARNING: WARNING: SMART TOILET CONTROL Installation and Maintenance Instructions Part# STC THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND FOLLOWED DURING BOTH INSTALLATION AND OPERATION.
More informationPrimaLine 1.5 XT Wet Location LED Tape Light
PrimaLine 1.5 XT Wet Location LED Tape Light 0.55 in. wide Field cuttable every 4 in. PrimaLine 1.5 XT offers extended maximum run lengths of 40 feet with the same lumen output, CRI, and wattage as the
More informationInstalling AZEK Evolutions Rail
Installing Evolutions Rail TM Contemporary Installing AZEK Evolutions Rail Installing Evolutions Rail Contemporary Style... 2 Installing CableRail by Feeney for Evolutions Rail Contemporary Style... 8
More informationDrywall with Plaster and Paint. Lamp: The average LED Life is 50,000 hours. per Foot. per Watt. (2x2.5WDC) (2x5WDC) (2x6WDC)
Drywall Drywall with Plaster and Paint 3.73" (9.5cm) 1" (2.5cm) 6" (15.2cm) 1'- 40' (30.5cm - 1219.2cm) Description: TruLine 1.6A, a versatile 24VDC linear plaster-in LED system, creates glare-free, indoor
More informationARROW SAW PRECISE CUT 8000 RPM WITH DUST COLLECTING ATTACHMENT INSTRUCTION BOOK MODEL NO
ATTENTION If any components of this unit are broken or the unit does not operate properly, please contact Cabela s Customer Service. Retail Store Purchases: 1-800-905-2731 (U.S. & Canada) Catalog and Internet
More informationPage 1 T O O L S A N D M AT E R I A L S R E Q U I R E D. 1. Screwdriver 2. Carpenter's level 3. Electrical Tape PA R T S L I S T. A.
T O O L S A N D M AT E R I A L S R E Q U I R E D 1. Screwdriver 2. Carpenter's level 3. Electrical Tape PA R T S L I S T A. Cabinet B. Wood Screw X4 C. Plastic wire connector x3 Page 1 I M P O R TA N T
More informationInstallation Instructions For Slider Casement Air Conditioners
Installation Instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT
More informationTS-700/1000 INVERTER Instruction Manual
TS-700/1000 INVERTER Instruction Manual TS-700/1000 Instruction Manual Index 1. Safety Guidelines... 1 2. Introduction... 1 2.1 Features... 1 2.2 Main Specification... 2 3. User Interface... 2 3.1 Front
More informationWall Mount Assembly and Mounting Guide (55 /84 )
Microsoft Surface Hub Wall Mount Assembly and Mounting Guide (55 /84 ) For mounting on a wall with wood studs These instructions assume wood-stud wall construction with 2-by-4 studs spaced 16 inches apart,
More informationLamp: The average LED Life is 50,000 hours. per Foot 2WDC (2.5WDC) per Watt. per Foot 5WDC Lumen values are based on the 3000K LED test.
Drywall Drywall with Plaster & Paint 2" (5.1cm) 1" (2.5cm) 6" (15.2cm) 1'- 40' (30.5cm - 1219.2cm) Description: TruLine.5A, a versatile 24VDC linear plaster-in LED system, creates glare-free, indoor architectural
More informationAliante Installation. Components included: Tools required: Not Included:
041137c 1 08.25.16 Important Notes: Please read entire guide before beginning fixture installation. For installation by a qualified electrician familiar with the construction and operation of luminaire
More informationFLATFROG MULTITOUCH 3200
FLATFROG MULTITOUCH 3200 Quick Assembly Guide Document Number LZN 100013 R1B Issue 2012-07 Industrial Design Casing Parts List b a Package contents Industrial design casing. The following items are included:
More informationInstallation Instructions
TECH SUPPORT The Watt Stopper, Inc. 2800 De La Cruz Blvd. Santa Clara, CA 95050, USA Tel: 1(800)879-8585 1(972)578-1699 Fax: 1(972)422-1311 www.wattstopper.com Outdoor 180 & 270 PIR Motion s Model#s: EW-100-120
More informationLL-105-R LED Dimmer & 0-10V Bridge Setup Guide
www.i2systems.com i2systems is a registered trademark of Integrated Illumination Systems, Inc. LightLink is a trademark of Integrated Illumination Systems, Inc. 2018 Integrated Illumination Systems, Inc.
More informationLine volt rail & fixtures. Low volt quick connect fixtures with transformers
INSTRUCTIONS: Line Volt Flexrail2 Safety Instructions: A qualified electrician must install system only. System is intended for installation in accordance with National Electric Code, local and Federal
More informationPVLP-156X. Owner s Manual VERTICAL LEG PRESS
VERTICAL LEG PRESS Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each workout.
More informationProduct Description. Quick Spec. Fully Dimmable: Voltage: Total Wattage: Beam Angle: Yes 24V DC 36W -150W 120º
RG OLOR HNGING L STRIP LIGHT Product escription Solid pollo s RG olor-changing L Strip Lights are designed with the ability to create over 16 million different colors by mixing Red, lue, and Green light.
More informationInstallation Instructions for DIY or Completed 45 Degree Light Channel
201 Edge Lighting. All Rights Reserved. Installation Instructions for DIY or Completed Degree Light Channel IMPORTANT INFORMATION - This instruction shows a typical installation. 11 W. Fullerton Ave Chicago,
More information1/4in. SHEET PALM SANDER
1/4in. SHEET PALM SANDER OPERATING INSTRUCTIONS SPECIFICATIONS ITEM# 151608 Voltage: Max. output: No load speed: Cord: 120V ~ 60Hz 180W 14000 RPM 6 feet (2m) Dust-Sealed On/off Switch Dust Extraction Adaptor
More informationALS450T. our most versatile SERIES
alumled SERIES ALS450T our most versatile luminaire CRI High Output (HO) > 90 DIMMING Forward Phase 0-10V 10V-0% (100% to 0% Dimming) 10V-1% (100% to 1% Dimming) DALI INTEGRAL DRIVER Driver On-Board WALL
More informationInstallation & Operation Manual
The eco-friendly solution to hard water SB-1200, SB-2000, SB-2800, SB-3600 & SB-4000 Installation & Operation Manual 10/13 Industrial Electronic Descaler 120/240 VAC (Auto Selected) Table of Contents Section
More informationdiode led 12VDC COMMERCIAL GRADE SPECIFICATION SHEET RECEIVE A UL LISTED DRIVER WHEN ORDERING THE LO-PRO JUNCTION BOX & DRIVER COMBO ON PAGE 2.
diode led a division of elemental ED 12VDC COMMERCIA GRADE 0-10V ED DIMMABE DRIVER 12VDC WET OCATIO DIMMABE SPECIFICATIO SHEET OVERVIEW 12VDC Commercial Grade 0-10V Dimmable ED Drivers are essential components
More informationAdvantages of Tara LED Landscape Lighting
Advantages of Tara LED Landscape Lighting for the Homeowner... Spectacular Effects * Even Illumination No Dark Zones * Warm White Light Colors * No UV or IR to Attract Insects * Night Sky Friendly Green
More information3% VOLTAGE DROP. Installation Instructions for 400 Watt 24 Volt DC RGB DMX LED Power Supply SAVE THESE INSTRUCTIONS!
Installation Instructions for 400 Watt 24 Volt DC RGB DMX LED Power Supply Doc # 904-PSB-400W-24VDC_06 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com
More information2011 / Circuit Tracer
INSTRUCTION MANUAL 2011 / 00521 Circuit Tracer Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. 52044992 2008 Greenlee Textron
More informationWARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE!
WARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE! General Safety Information To reduce the risk of death, personal injury or property damage from
More informationPow-R-Feed Systems Service Manual
Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious
More informationPSM-144X SMITH MACHINE. Owner s Manual
SMITH MACHINE Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each workout.
More informationPVKC-83X. Owner s Manual VERTICAL KNEE RAISE
VERTICAL KNEE RAISE Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each
More informationGATE LIMIT RELAY KIT INSTALLATION INSTRUCTIONS GATE OPERATORS:
GATE LIMIT RELAY KIT INSTALLATION INSTRUCTIONS GATE OPERATORS: SW420/470/490, SL540/570/580/590 PARTS SUPPLIED Part # Qty Description 01-20322 1 Modification Instructions 27-20108 2 Cable Tie 76-20431
More informationCONTENTS OF THE BOX. *PIR sensor only **Dual Technology and PIR sensors only. Description PIR Ultrasonic Dual Technology
Instruction Bulletin 63249-420-283A4 08/2009 Wall Mount Occupancy Sensor SLSWPS1500, SLSWUS1500, SLSWDS1500 INTRODUCTION Wall Mounted Occupancy Sensors are Class 2 devices ideal for use in business or
More informationSLOT INSTALLATION GUIDE Indoor IP20
Please read entire guide prior to starting installation. Sections: Pre-Installation Single Run Fed From Both Ends NOTES 1. IP40 and lower tape must be installed indoors only. Installing outdoors will void
More informationINSTALLATION INSTRUCTIONS LARGE FLAT PANEL IN WALL ENCLOSURE Model: PAC-500
INSTALLATION INSTRUCTIONS LARGE FLAT PANEL IN WALL ENCLOSURE Model: PAC-500 Specifications: Designed for in-wall installation spanning a minimum of 3 wood studs, 16" on center. Accomodates MWR, PWR and
More informationARCTIC TRACE INSTALLATION INSTRUCTIONS 352C Hazardous Location Water Proof Strain Relief Kit for TL Series Heating Cable
ARCTIC TRACE INSTALLATION INSTRUCTIONS 352C Hazardous Location Water Proof Strain Relief Kit for TL Series Heating Cable SEALING GLAND SEALING PAST WARNING: to prevent electric shock or fire, this product
More informationTHIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationInstallation Instructions
SPECIFICATIONS WS-200 Automatic PIR Wall Switch Voltages...........................120 or 277VAC, 60Hz Requirements @ 120VAC, 60Hz........0-800W ballast & tungsten @ 277VAC, 60Hz.................0-1200W
More informationInstallation Instructions
READ BEFORE INSTALLING UNIT For Slider Casement Air Conditioners To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:
More information4 Channel Contact Closure DIN Fiber Link System
USER GUIDE RLH Industries, Inc. The leader in rugged fiber optic technology. U-027 2018A-0213 4 Channel Contact Closure DIN Fiber Link System SYSTEM INSTALLATI INFORMATI Description The 4 Channel Contact
More informationProduct Description. Quick Spec. Fully Dimmable: Voltage: Total Wattage: Beam Angle: Yes 24V DC 36W -144W 120º
RG WTRPROOF OLOR HNGING L STRIP LIGHT Product escription Solid pollo s Waterproof RG olor-changing L Strip Lights are designed with the ability to create millions of different colors by mixing Red, lue,
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
T0412 / T0413 ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THESE INSTRUCTIONS. Hardware
More informationTube Facing Tool.
www.swagelok.com Tube Facing Tool This manual contains important information for the safe and effective operation of the Swagelok TF72 series tube facing tool. Users should read and understand its contents
More informationTurn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel. Pleasegotowww.quoizel.forproductcleaningtips.GototheCare+Maintenance selection. ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wire
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationInstallation Guide. 84 H and 95 H
Installation Guide 84 H and 95 H Stacker Bracket Connectors for topper of the wall system Step 1: (for 95 H and 108 H only) Attach glass topper to the wall system using the bracket shown (84 H wall system
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationOperation Manual. Congratulations on purchasing your high quality AIMS Power pure sine inverter!
Operation Manual Congratulations on purchasing your high quality AIMS Power pure sine inverter! It is very important that you read and understand this instruction manual completely prior to use. Contained
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationSMART TOILET CONTROL
WARNING: WARNING: SMART TOILET CONTROL Installation and Maintenance Instructions Part# STC THE FOLLOWING ARE CAUTIONARY STATEMENTS THAT MUST BE READ AND FOLLOWED DURING BOTH INSTALLATION AND OPERATION.
More informationINSTALLATION LED DRIVER. Top view. LED Module. Barrel. Block side. 2 black or white wires. 2 red wires. Gland. + side. Cover. Mounting Screws.
110VAC INSTALLATION LED DRIVER Strain Relief Barrel 2 black or white wires LED Module Terminal Block side Determine where you wish the LED MiniDisc Scoop Light to be placed. 1. Drill a 1.0" diameter hole
More informationInstallation Instructions
Installation Instructions Self-Cleaning Radiant Trivection Electric Slide-In Range JS998 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.geappliances.com BEFORE YOU BEGIN Read
More informationGE Monogram. Installation. Instructions. 36" Vent Hood. Model ZV750. Call anywhere in the US and Canada -
at :: rangehoods. com GE Monogram Instructions Model ZV750 GE Monogram at:: rangehoods. com is a division of CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:
More informationDaytime Running Lights - Splice-in (10-12 All):
Time Necessary: Approximately 1 hour Tools Required: Heat Gun Installation Procedure: Daytime Running Lights - Splice-in (10-12 All): 1. It is recommended that the positive terminal be removed from the
More informationMaxLite Linear Strip ECO Series
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationSpeaker Attachment Bracket
4-269-373-E1(1) Speaker Attachment Bracket Operating Instructions WS-32SE1B/WS-40SE1B/WS-46SE1B Thank you for purchasing this unit. This manual explains important safety instructions to prevent accidents
More informationFACTORY STRETCH INSTALLATION INSTRUCTIONS
!! Important!! Make sure all power is disconnected prior to installation. Wiring to be done according to Local and National Electric Codes by a qualified electrician. Make sure the building and/or structure
More informationFoil Transfer Starter Kit
EN Foil Transfer Starter Kit About the Foil Transfer Starter Kit You can create high-quality designs by using the pressing tool to apply foil with your cutting machine. Important Safety Instructions WARNING
More informationIn-Wall Pool Step Assembly Instructions
In-Wall Pool Step Assembly Instructions BE SURE TO READ ALL INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. This instruction sheet is to be used in conjunction with the pool assembly guide included with
More informationInstallation Instructions
Installation Instructions READ BEFORE INSTALLING UNIT For Slider Casement Air Conditioners INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning. Follow each step as
More informationSMARTfit Functional and Brain Fitness Training Multi-Station Trainer Installation for Stud and Concrete Walls (US)
SMARTfit Functional and Brain Fitness Training Multi-Station Trainer Installation for Stud and Concrete Walls (US) 2017 SMARTfit, Inc. www.smartfitinc.com 1 Unlike other fitness equipment which may require
More informationDART MAXI DAL- cod. 2DL7CS00. To ensure a maximum efficient use of the product, read the instructions before proceeding installment.
Targetti USA - A Targetti Group Company - 750-A W 7th St. Costa Mesa, CA 967 - Phone (74) 53-99 - Email:targettiusa@targetti.com - www.targetti.us - 05..7 - Page of 0 DART MAXI DAL- cod. DL7CS00 9." 8.43"
More informationTHERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each wo
DUMBBELL RACK Owner s Manual WWW.BODYSOLID.COM THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: Inspect equipment before each workout.
More informationInstallation Instructions for DIY or Completed Light Channel.6 Millwork
2017 Edge Lighting. All Rights Reserved. 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 77-770-1195 Fax: 77-95-561 www.edgelighting.com info@edgelighting.com LCMW.6- - - 904-LCMW.6_02 Installation Instructions
More informationQUANTUM 2 CIRCLE 24 Installation Instructions
Installation Instructions #CH-C-24-KIT #CH-C-24-2FT #CH-C-24-4FT #CH-C-24-6FT #CH-C-24-8FT Custom #CH-C-24 Sections: Pg. 2 Fixture Kit Channel Preparation Pg. 6 Suspension Installation Version 3 Page 1
More informationCustom Pendant- Hardwire Assembly and Installation Instructions
Custom Pendant- Hardwire Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More information