ISO INTERNATIONAL STANDARD

Transcription

1 INTERNATIONAL STANDARD ISO First edition Textiles Determination of the abrasion resistance of fabrics by the Martindale method Part 1: Martindale abrasion testing apparatus Textiles Détermination de la résistance à l abrasion des étoffes par la méthode Martindale Partie 1: Appareil d essai d abrasion Martindale A Reference number ISO :1998(E)

2 ISO :1998(E) Contents Page 1 Scope Normative references Definitions Principle Apparatus Auxiliary materials Assembly and maintenance of the apparatus Annex A (normative) Method for checking the Lissajous figure...10 Annex B (normative) Method for measuring the indentation hardness of foam...11 Bibliography ISO 1998 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale 56 CH-1211 Genève 20 Switzerland Internet iso@iso.ch Printed in Switzerland ii

3 ISO ISO :1998(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO was prepared by Technical Committee ISO/TC 38, Textiles. ISO consists of the following parts under the general title Textiles Determination of the abrasion resistance of fabrics by the Martindale method: Part 1: Martindale abrasion testing apparatus Part 2: Determination of specimen breakdown Part 3: Determination of mass loss Part 4: Assessment of appearance change Annexes A and B form an integral part of this part of ISO ii

4 ISO :1998(E) ISO Introduction The choice of method of abrasion testing is established before the start of the testing and recorded in the test report, since the results of the different methods cannot be compared with each other. The determination of resistance to pilling of fabrics using the Martindale apparatus is given in ISO 12945, Textiles Determination of the resistance to pilling and change of appearance of fabrics, parts 1, 2 and 3 1). 1) These three parts of International Standard ISO are yet to be published. iv

5 ISO INTERNATIONAL STANDARD ISO :1998(E) Textiles Determination of the abrasion resistance of fabrics by the Martindale method Part 1: Martindale abrasion testing apparatus 1 Scope This part of ISO specifies requirements for the Martindale testing apparatus and auxiliary materials for use in the test methods specified in parts 2 to 4 of ISO for determination of the abrasion resistance of fabrics. This part of ISO is applicable to apparatus for the testing of: a) woven and knitted fabrics; b) pile textiles having a pile height of up to 2 mm; c) nonwovens. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 137:1975, Wool Determination of fibre diameter Projection microscope method. ISO 286-2:1988, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts. ISO 845:1988, Cellular plastics and rubbers Determination of apparent (bulk) density. ISO 2060:1994, Textiles Yarn from packages Determination of linear density (mass per unit length) Skein method. ISO 2061:1995, Textiles Determination of twist in yarns Direct counting method. ISO :1998, Rubber- or plastics-coated fabrics Determination of roll characteristics Part 3: Method for the determination of thickness. ISO 3074:1975, Wool Determination of dichloromethane Soluble matter in combed sliver. ISO 3801:1977, Textiles Woven fabrics Determination of mass per unit length and mass per unit area. ISO 5084:1996, Textiles Determination of thickness of textiles and textile products. 1

6 ISO :1998(E) ISO ISO :1984, Textiles Woven Fabrics Construction Methods of analysis Part 2: Determination of number of threads per unit length. ISO :1998, Textiles Determination of the abrasion resistance of fabrics by the Martindale method Part 2: Determination of specimen breakdown. ISO :1998, Textiles Determination of the abrasion resistance of fabrics by the Martindale method Part 3: Determination of mass loss. 3 Definitions For the purposes of this part of ISO 12947, the following definitions apply. 3.1 abrasion rub one revolution of the two outer drives of the Martindale abrasion tester 3.2 abrasion cycle completion of all the translational abrasion movements tracing a Lissajous figure comprising 16 rubs, i.e. 16 revolutions of the two outer drives and 15 revolutions of the inner drive of the Martindale abrasion tester 3.3 inspection interval number of continuously performed rubs 3.4 Lissajous figure figure created by movement which changes from a circle to gradually narrowing ellipses, until it becomes a straight line, from which progressively widening ellipses develop, in a diagonally opposite direction before the pattern is repeated 3.5 work station abrading table 4 Principle The Martindale abrasion tester subjects a circular specimen to a defined load and rubs it against an abrasive medium (i.e standard fabric) in a translational movement tracing a Lissajous figure. The specimen holder, containing either specimen or abrasive medium depending on which method (ISO 12947, Parts 2, 3 or 4) is being used, is additionally freely rotatable around its own axis perpendicular to the horizontal plane. The specimen is subjected to abrasive wear for a predetermined number of rubs. The number of abrasion rubs making up the inspection interval depends upon the product type and method of assessment. 5 Apparatus 5.1 General The test apparatus consists of a baseplate on which are mounted the abrading tables and drive mechanism. The drive mechanism consists of two outer drives and an inner drive which cause the specimen holder guide plate to trace a Lissajous figure (see annex A). NOTE The Martindale apparatus does not generate a perfect Lissajous motion. 2