Australian Standard RADIOGRAPHY OF WELDED BUTT JOINTS IN METAL. Part 2 IMAGE QUALITY INDICATORS (IQI) AND RECOMMENDATIONS FOR THEIR USE

Size: px
Start display at page:

Download "Australian Standard RADIOGRAPHY OF WELDED BUTT JOINTS IN METAL. Part 2 IMAGE QUALITY INDICATORS (IQI) AND RECOMMENDATIONS FOR THEIR USE"

Transcription

1 AS 2177, Part Australian Standard RADIOGRAPHY OF WELDED BUTT JOINTS IN METAL Part 2 IMAGE QUALITY INDICATORS (IQI) AND RECOMMENDATIONS FOR THEIR USE

2 This standard, prepared by Committee MT/7, Non-destructive Testing of Metals and Materials, was approved on behalf of the Council of the Standards Association of Australia on 14 January 1982, and was published on 19 April The following scientific, industrial and governmental organizations and departments were officially represented on the committee entrusted with the preparation of this standard: Australian Atomic Energy Commission Australian Gas Association Australian Institute for Non-destructive Testing Australian Pipeline Industry Association Australian Welding Institute Bureau of Steel Manufacturers of Australia Commonwealth Aircraft Corporation Confederation of Australian Industry Department of Defence Department of Industrial Relations, N.S.W. Department of Labour and Industry, Victoria Department of Productivity Electricity Supply Association of Australia Institute of Australian Foundrymen Metal Trades Industries Association of Australia National Association of Testing Authorities Pipeline Authority Railways of Australia Committee Society of Automotive Engineers Australasia Review of Australian Standards. To keep abreast of progress in industry, Australian Standards are subject to periodic review and are kept up to date by the issue of amendments or new editions as necessary. It is important therefore that Standards users ensure that they are in possession of the latest edition, and any amendments thereto. Full details of all Australian Standards and related publications will be found in the Standards Australia Catalogue of Publications; this information is supplemented each month by the magazine The Australian Standard, which subscribing members receive, and which gives details of new publications, new editions and amendments, and of withdrawn Standards. Suggestions for improvements to Australian Standards, addressed to the head office of Standards Australia, are welcomed. Notification of any inaccuracy or ambiguity found in an Australian Standard should be made without delay in order that the matter may be investigated and appropriate action taken.

3 AS 2177, Part Australian Standard RADIOGRAPHY OF WELDED BUTT JOINTS IN METAL Part 2 IMAGE QUALITY INDICATORS (IQI) AND RECOMMENDATIONS FOR THEIR USE Firstpublished (asasb262) AS2177,Part2firstpublished Second edition PUBLISHED BY STANDARDS AUSTRALIA (STANDARDS ASSOCIATION OF AUSTRALIA) 1 THE CRESCENT, HOMEBUSH, NSW 2140 ISBN

4 AS 2177, Part PREFACE This edition of this standard was prepared by the Association s Committee on Nondestructive Testing of Metals and Materials at the request of the Metals Standards Board to supersede the 1979 edition, which constituted the revision, metrication and replacement of AS B Because of the widespread use in Australia of image quality indicator (IQI) systems specified by various standards bodies*, the committee, during the revision, resolved to retain those systems in this standard. Imperial units of measurement for plaque/hole type IQI based on the ASME series have also been retained because of the impracticability of changing to the International (SI) System of units. The committee proposes to amend the published standard when the American system is changed and new plaque IQI are available for commercial use in Australia. During preparation of this edition, consideration was given to matters raised at seminars held to discuss the standard. Changes incorporated in this standard are intended to remove any ambiquity which might have existed in the 1979 edition. Known errors have also been eliminated. Relevant tables and appendices have been updated to align with the new edition of Part I of the standard. Graphical presentations of readily achievable IQI sensitivity percent have also been included. Data used in the compilation of the relationships between different types of IQI were taken from a paper by E.L. Criscuolo, Radiographic Image Quality Standards, and from ASME, SE 142. This standard may require reference to the following documents: AS 1929 Non-destructive Testing Glossary of Terms AS 2177 Radiography of Welded Butt Joints in Metal Part 1 Methods of Test SAA MP19 Report on Preferred Numbers and Their Use DIN Non-destructive Testing Image Quality of X-ray and Gamma-ray Radiographs of Metallic Materials, Definitions, Wire Penetrameter BS 3971 Image Quality Indicators for Radiography and Recommendations for Their Use AFNOR A Radiographic Examination of Steel of Thickness up to and including 180 mm ASME, SE 142 Standard Methods for Controlling Quality of Radiographic Testing ISO 1027 Radiographic Image Quality Indicators Principles and Identification ISO 2504 Radiography of Welds and Viewing Conditions for Films Utilization and Recommended Patterns of Image Quality Indicators (IQI) * International Organization for Standardization (ISO) British Standards Institution (BSI) Deutsches Institut fur Normung (DIN) American Society of Mechanical Engineers (ASME) Association Francaise de Normalisation (AFNOR) Presented at the Inter-American Conference on Materials Technology, May 1968, San Antonio, Texas, and published by ASME in Materials Technology An Inter-American Approach, pp Copyright STANDARDS AUSTRALIA Users of Standards are reminded that copyright subsists in all Standards Australia publications and software. Except where the Copyright Act allows and except where provided for below no publications or software produced by Standards Australia may be reproduced, stored in a retrieval system in any form or transmitted by any means without prior permission in writing from Standards Australia. Permission may be conditional on an appropriate royalty payment. Requests for permission and information on commercial software royalties should be directed to the head office of Standards Australia. Standards Australia will permit up to 10 percent of the technical content pages of a Standard to be copied for use exclusively inhouse by purchasers of the Standard without payment of a royalty or advice to Standards Australia. Standards Australia will also permit the inclusion of its copyright material in computer software programs for no royalty payment provided such programs are used exclusively in-house by the creators of the programs. Care should be taken to ensure that material used is from the current edition of the Standard and that it is updated whenever the Standard is amended or revised. The number and date of the Standard should therefore be clearly identified. The use of material in print form or in computer software programs to be used commercially, with or without payment, or in commercial contracts is subject to the payment of a royalty. This policy may be varied by Standards Australia at any time.

5 3 AS 2177, Part CONTENTS Page FOREWORD... 4 SECTION 1. SCOPE, DEFINITIONS AND GENERAL REQUIREMENTS 1.1 Scope Definitions Required Characteristics of IQI SECTION 2. RECOMMENDATIONS FOR THE USE OF IQI 2.1 Selection of IQI Location of IQI Viewing of Radiographs Assessment of IQI Percent Sensitivity Equivalent Sensitivity APPENDICES A Materials of Construction of Image Quality Indicators B Typical Examples of Film Types

6 AS 2177, Part STANDARDS ASSOCIATION OF AUSTRALIA Australian Standard for RADIOGRAPHY OF WELDED BUTT JOINTS IN METAL PART 2 IMAGE QUALITY INDICATORS (IQI) AND RECOMMENDATIONS FOR THEIR USE FOREWORD The elements, wires or holes, of image quality indicators (IQI) are used to indicate the sensitivity of the radiographic process in revealing the presence of any discontinuities. The image quality is characterized by the smallest element of a series of wires, or by the smallest of a series of holes in plates of different thicknesses, the images of which can be discerned visually when a film is placed on an illuminated screen of the required brightness (see AS 2177, Part 1). NOTE: Throughout this standard, IQI is used to denote singular and plural of image quality indicator. It should be pointed out that the following parameters apply to the uses of IQI: (a) (b) (c) (d) Defect detection sensitivity is related only in a general fashion to IQI sensitivity. For any given radiographic test method, the numerical value of the IQI sensitivity depends on the type of the IQI used. For any given radiographic test method and IQI, the percentage sensitivity will not be the same for different metal thicknesses. For any given metal and thickness, it is possible to change defect sensitivity without significant change in IQI sensitivity by changing the radiographic method. (e) The assessment of the visibility of details of an IQI is subjective and it depends upon the following factors: (i) Visual acuity. (ii) Viewing conditions. (iii) Experience and ability in assessing IQI images. (iv) Radiographic contrast. For these reasons, although the specified IQI sensitivity value may be attained, the practices outlined in AS 2177, Part 1 require that all factors affecting contrast and definition be considered, i.e. A. Tube voltage or type of radioisotope. B. Source-to-film and object-to-film distances. C. Film type and screen material and thickness. D. Film density and processing. In order to assist committees responsible for the drafting of standards in which radiographic methods are specified and users of this standard, recommendations given in AS 2177, Part 1 are repeated in Tables 1 and 2 which show readily achievable values of sensitivity which may be obtained with different radiographic methods for steel. Figs 1A, 1B, 2A and 2B show a best-fit graphical presentation of information contained in Table 2. COPYRIGHT

7 5 AS 2177, Part TABLE 1 TEST METHOD DESIGNATION NUMBER Radiographic method designation number Radiation source Exposure method SAA film type designation (see Appendix C) Typical application XR1/S X-rays Single plate or wall 1 (very fine grain) When a very high level of sensitivity is required XR1/DWS X-rays Double-wall, singleimage XR1/DWD X-rays Double-wall, double-image 1 (very fine grain) As for XR1/S where internal access is not practicable 1 (very fine grain) As for XR1/DWS where the pipe diameter is 90 mm or below XR2/S X-rays Single plate or wall 2 (fine grain) High sensitivity, general use XR2/DWS X-rays Double-wall, singleimage XR2/DWD X-rays Double-wall, double-image 2 (fine grain) As for XR2/S where internal access is not practicable 2 (fine grain) As for XR2/DWS where the pipe diameter is 90 mm or below XR3/S X-rays Single plate or wall 3 (medium grain) High speed method when the detection of fine discontinuities is not required XR3/DWS X-rays Double-wall, singleimage XR3/DWD X-rays Double-wall, double-image 3 (medium grain) As for XR3/S where internal access is not practicable 3 (medium grain) As for XR3/DWS where pipe diameter is 90 mm or below GR1/S Gamma-rays Single plate or wall 1 (very fine grain) Where the sensitivity achievable by X-ray equipment is not required GR1/DWS Gamma-rays Double-wall, singleimage GR1/DWD Gamma-rays Double-wall, double-image 1 (very fine grain) As for GR1/S where internal access is not practicable 1 (very fine grain) As for GR1/DWS where pipe diameter is 90 mm or below GR2/S Gamma-rays Single plate or wall 2 (fine grain) General use where the sensitivity achievable by GR1 is not required GR2/DWS Gamma-rays Double-wall, singleimage GR2/DWD Gamma-rays Double-wall, double-image 2 (fine grain) As for GR2/S where internal access is not practicable 2 (fine grain) As for GR2/DWS where pipe diameter is 90 mm or below GR 3/S Gamma-rays Single plate or wall 3 (medium grain) High speed method when the detection of fine discontinuities is not required GR3/DWS Gamma-rays Double-wall, singleimage GR3/DWD Gamma-rays Double-wall, double-image 3 (medium grain) As for GR2/S where internal access is not possible 3 (medium grain) As for GR3/DWS where pipe diameter is 90 mm or below COPYRIGHT

8 AS 2177, Part TABLE 2* READILY ACHIEVABLE WIRE IQI SENSITIVITIES FOR STEEL EXPRESSED AS SMALLEST WIRE VISIBLE ON RADIOGRAPH WITH CORRESPONDING SENSITIVITY VALUE Radiographic test method XR1 Weld metal thickness, mm XR2 XR3 GR1 GR2 GR3 * The values of sensitivity quoted are not necessarily the optimum value which can be achieved, but they are included for information and comparative purposes and should not be taken as mandatory requirements for any particular method. Sensitivity values quoted for gamma ray methods are for Iridium 192 (Ir 192 ) in accordance with the thickness range given in Table 3 of AS 2177, Part 1, and for Co 60 for thicker sections up to 200 mm. Sensitivities quoted for GR methods for less than 10 mm and over 200 mm are included for information only. Attention is drawn to the improved sensitivity which can be obtained with Ytterbium 169(Yb 169 ) in the range 6 mm to 20 mm. Sensitivity values are rounded to nearest 0.1 percent. The typical values of sensitivity quoted for each of the test methods in Table 2 are not to be taken as mandatory unless specified or agreed between contracting parties. COPYRIGHT

9 7 AS 2177, Part Fig. 1A. READILY ACHIEVABLE WIRE IQI SENSITIVITY PERCENT FOR THICKNESS RANGE FOR STEEL UP TO 125 mm XR METHODS COPYRIGHT

10 AS 2177, Part Fig. 1B. READILY ACHIEVABLE WIRE IQI SENSITIVITY PERCENT FOR THICKNESS RANGE FOR STEEL UP TO 85 mm XR METHODS COPYRIGHT

11 9 AS 2177, Part Fig. 2A. READILY ACHIEVABLE WIRE IQI SENSITIVITY PERCENT FOR THICKNESS RANGE FOR STEEL UP TO 300 mm GR METHODS COPYRIGHT

12 AS 2177, Part Fig. 2B. READILY ACHIEVABLE WIRE IQI SENSITIVITY PERCENT FOR THICKNESS RANGE FOR STEEL UP TO 70 mm GR METHODS COPYRIGHT

13 11 AS 2177, Part SECTION 1. SCOPE, DEFINITIONS AND GENERAL REQUIREMENTS 1.1 SCOPE. This standard specifies requirements for three types of image quality indicators (IQI) used in X-ray or gamma-ray radiographic examination of welded butt joints in metal products, viz (a) wire IQI (W); (b) step/hole IQI (SH); and (c) plaque/hole IQI (PH); and includes recommendations for their use. 1.2 DEFINITIONS. For the purposes of this standard, the definitions given in AS 1929 and the following definition apply: Element a wire in a wire type IQI or a hole in a plaque of different thicknesses used to assess the sensitivity of the radiographic process. 1.3 REQUIRED CHARACTERISTICS OF IQI Wire IQI (W) General. Wire IQI shall consist of a series of wires of minimum length 25 mm mounted side by side in parallel, with a distance between the axes of the wires of not less than 5 mm, and arranged in order of increasing diameter. The diameter sizes should be determined as a consecutive series of numbers taken in general from the R10 series of preferred numbers. Exceptionally, and in particular for use with thick materials, the R20 series of preferred numbers may be used. An example of a wire IQI is given in Fig Permitted tolerances on the wire diameters for the R10 series of preferred numbers are given in Table 1.1. This system provides for a series of three IQI, each comprising seven wires. Each wire diameter is denoted by a corresponding wire number, as shown in Table 1.2. For information on IQI materials see Appendix A. Wire IQI are made up as shown in Table 1.3. TABLE 1.3 STANDARD MODELS (WIRE IQI) IQI DIN 1/7 DIN 6/12 DIN 10/ Wire numbers Construction. Wires shall be mounted between low radiation absorbent protective sheathing material, such as polyethylene film. NOTE: Where the IQI is composed of thin aluminium or magnesium wires, the thickness of the protective sheathing should not exceed 0.05 mm. The protective sheathing shall preferably be flexible and the material, adjacent to the wires, as thin as possible and fastened so as to ensure that the separation between wires is maintained Identification. Each wire IQI shall contain lead symbols giving the following information: (a) The smallest and largest wire numbers (see Table 1.2). (b) The material of which the IQI is made. (c) The specification with which the IQI complies. Typical IQI and identification markings are shown in Fig The size of the symbols shall be such that they are readily discernible on radiographs. Fig EXAMPLE OF WIRE TYPE IQI TABLE 1.1 PERMITTED TOLERANCES ON WIRE DIAMETERS* Wire diameter, φ mm 0 < φ < φ < φ < φ 4 Tolerance mm ± ± 0.01 ± 0.02 ± 0.03 * Tolerances are correct for steel. For other metals or alloys it is recommended that production conditions be such that the tolerances are as near as possible to those fixed for steel. TABLE 1.2 WIRE DIAMETERS AND NUMBERS Fig WIRE TYPE IQI Diameter, mm Wire number

14 The remainder of this document is available for purchase online at SAI Global also carries a wide range of publications from a wide variety of Standards Publishers: Click on the logos to search the database online.

AS Australian Standard STEEL WIRE FOR TENDONS IN PRESTRESSED CONCRETE. This is a free 5 page sample. Access the full version online.

AS Australian Standard STEEL WIRE FOR TENDONS IN PRESTRESSED CONCRETE. This is a free 5 page sample. Access the full version online. AS 1310 1987 Australian Standard STEEL WIRE FOR TENDONS IN PRESTRESSED CONCRETE This Australian Standard was prepared by Committee BD/23, Structural Steel. It was approved on behalf of the Council of the

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 1167.2:1999 Australian/New Zealand Standard Welding and brazing Filler metals Part 2: Filler metal for welding AS/NZS 1167.2:1999 This Joint Australian/New Zealand Standard was prepared by Joint

More information

AS Australian Standard METRIC SCREW THREADS FOR FASTENERS. This is a free 6 page sample. Access the full version online.

AS Australian Standard METRIC SCREW THREADS FOR FASTENERS. This is a free 6 page sample. Access the full version online. AS 1275 1985 Australian Standard METRIC SCREW THREADS FOR FASTENERS This Australian standard was prepared by Committee ME/28, Screw Threads. It was approved on behalf of the Council of the Standards Association

More information

Australian Standard. Paper sizes AS [Based on and including the full text of ISO 216:1975 and ISO 217:1995]

Australian Standard. Paper sizes AS [Based on and including the full text of ISO 216:1975 and ISO 217:1995] AS 1612 1999 Australian Standard Paper sizes [Based on and including the full text of ISO 216:1975 and ISO 217:1995] This Australian Standard was prepared by Committee IT/8, Paper Stationery. It was approved

More information

AS This is a free 6 page sample. Access the full version online. Australian Standard GAUGING OF METRIC SCREW THREADS

AS This is a free 6 page sample. Access the full version online. Australian Standard GAUGING OF METRIC SCREW THREADS AS 1014 1986 Australian Standard GAUGING OF METRIC SCREW THREADS This Australian standard was prepared by Committee ME/28, Screw Threads. It was approved on behalf of the Council of the Standards Association

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 2451:1998 Australian/New Zealand Standard Bolts, screws and nuts with British Standard Whitworth threads (rationalized series) AS/NZS 2451:1998 This Joint Australian/New Zealand Standard was prepared

More information

Australian Standard. ISO system of limits and fits. Part 1: Bases of tolerances, deviations and fits AS ISO 286-1:1988

Australian Standard. ISO system of limits and fits. Part 1: Bases of tolerances, deviations and fits AS ISO 286-1:1988 AS 1654.1 1995 ISO 286-1:1988 Australian Standard ISO system of limits and fits Part 1: Bases of tolerances, deviations and fits This Australian Standard was prepared by Committee ME/27, Engineering Tolerance

More information

Australian Standard. Unified (ISO inch) screw threads, associated gauges, and gauging practice AS

Australian Standard. Unified (ISO inch) screw threads, associated gauges, and gauging practice AS AS 3635 1990 Australian Standard Unified (ISO inch) screw threads, associated gauges, and gauging practice This Australian Standard was prepared by Committee ME/28, Screw Threads. It was approved on behalf

More information

Australian/New Zealand Standard

Australian/New Zealand Standard Australian/New Zealand Standard Textiles Natural and man-made fibres Generic names This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee CS/4, Care Labelling of Textiles.

More information

Australian Standard. Precast reinforced concrete box culverts

Australian Standard. Precast reinforced concrete box culverts AS 1597.2 1996 Australian Standard Precast reinforced concrete box culverts Part 2: Large culverts (from 1500 mm span and up to and including 4200 mm span and 4200 mm height) This Australian Standard was

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 1102.111:1997 IEC 617-11:1996 Australian/New Zealand Standard Graphical symbols for electrotechnical documentation Part 111: Architectural and topographical installation plans and diagrams [ IEC

More information

Item designation in electrotechnology

Item designation in electrotechnology AS 3702 1989 Australian Standard Item designation in electrotechnology This Australian Standard was prepared by Committee TE/13, Symbols, Units & Quantities for Electrotechnology. It was approved on behalf

More information

Australian/New Zealand Standard

Australian/New Zealand Standard Australian/New Zealand Standard Quality management and quality assurance Vocabulary This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee QR/7, Quality Terminology. It was

More information

AS Australian Standard. Guarding and safe use of woodworking machinery. This is a free 7 page sample. Access the full version online.

AS Australian Standard. Guarding and safe use of woodworking machinery. This is a free 7 page sample. Access the full version online. AS 1473 1991 Australian Standard Guarding and safe use of woodworking machinery This Australian Standard was prepared by Committee SF/7, Guarding of Woodworking Machinery. It was approved on behalf of

More information

Australian Standard. Precast reinforced concrete box culverts. Part 1: Small culverts (not exceeding 1200 mm width and 900 mm depth) AS 1597.

Australian Standard. Precast reinforced concrete box culverts. Part 1: Small culverts (not exceeding 1200 mm width and 900 mm depth) AS 1597. AS 1597.1 1974 Australian Standard Precast reinforced concrete box culverts Part 1: Small culverts (not exceeding 1200 mm width and 900 mm depth) The following industrial and governmental organizations

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 2622:1996 Australian/New Zealand Standard Textile products Fibre content labelling AS/NZS 2622:1996 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee CS/4, Care

More information

Australian Standard. Switchgear assemblies and ancillary equipment for alternating voltages above 1 kv AS

Australian Standard. Switchgear assemblies and ancillary equipment for alternating voltages above 1 kv AS AS 2067 1984 Australian Standard Switchgear assemblies and ancillary equipment for alternating voltages above 1 kv [Title allocated by Defence Cataloguing Authority: SWITCHGEAR ASSEMBLIES, ELECTRICAL AND

More information

Australian Standard. Safeguarding of machinery. Part 1: General principles AS

Australian Standard. Safeguarding of machinery. Part 1: General principles AS AS 4024.1 1996 Australian Standard Safeguarding of machinery Part 1: General principles This Australian Standard was prepared by Committee SF/41, General Principles for the Guarding of Machinery. It was

More information

Australian Standard. Graphical symbols for general engineering. Part 3: Welding and non-destructive examination AS AS 1101.

Australian Standard. Graphical symbols for general engineering. Part 3: Welding and non-destructive examination AS AS 1101. AS 1101.3 2005 AS 1101.3 2005 Australian Standard Graphical symbols for general engineering Part 3: Welding and non-destructive examination This Australian Standard was prepared by Committee WD-001, Welding

More information

ISO INTERNATIONAL STANDARD. Non-destructive testing of welds Radiographic testing Part 1: X- and gamma-ray techniques with film

ISO INTERNATIONAL STANDARD. Non-destructive testing of welds Radiographic testing Part 1: X- and gamma-ray techniques with film INTERNATIONAL STANDARD ISO 17636-1 First edition 2013-01-15 Non-destructive testing of welds Radiographic testing Part 1: X- and gamma-ray techniques with film Contrôle non destructif des assemblages soudés

More information

Australian Standard. Non-destructive testing Ultrasonic methods Evaluation and quality classification of metal bearing bonds (ISO :1992, MOD)

Australian Standard. Non-destructive testing Ultrasonic methods Evaluation and quality classification of metal bearing bonds (ISO :1992, MOD) AS 2824 2003 AS 2824 Australian Standard Non-destructive testing Ultrasonic methods Evaluation and quality classification of metal bearing bonds (ISO 4386-1:1992, MOD) This Australian Standard was prepared

More information

Part 3: Image quality classes

Part 3: Image quality classes INTERNATIONAL STANDARD ISO 19232-3 Second edition 2013-06-15 Non-destructive testing Image quality of radiographs Part 3: Image quality classes Essais non destructifs Qualité d image des radiogrammes Partie

More information

Standards Australia LICENCE

Standards Australia LICENCE Standards Australia LICENCE Title: Licensee: Date: Conditions of use (Click here for full conditions of Licence) Check if current WEB SEARCH Find similar documents StandardsWatch (Info and Login) Visit

More information

ISO INTERNATIONAL STANDARD. Non-destructive testing of welds Radiographic testing of fusionwelded

ISO INTERNATIONAL STANDARD. Non-destructive testing of welds Radiographic testing of fusionwelded INTERNATIONAL STANDARD ISO 17636 First edition 2003-09-15 Non-destructive testing of welds Radiographic testing of fusionwelded joints Contrôle non destructif des assemblages soudés Contrôle par radiographie

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 4680:2006 AS/NZS 4680:2006 Australian/New Zealand Standard Hot-dip galvanized (zinc) coatings on fabricated ferrous articles AS/NZS 4680:2006 This Joint Australian/New Zealand Standard was prepared

More information

Australian Standard. ISO metric hexagon bolts and screws Product grade C. Part 1: Bolts AS ISO 4016:1999

Australian Standard. ISO metric hexagon bolts and screws Product grade C. Part 1: Bolts AS ISO 4016:1999 AS 1111.12000 ISO 4016:1999 AS 1111.1 Australian Standard ISO metric hexagon bolts and screws Product grade C Part 1: Bolts [ISO title: Hexagon head boltsproduct grade C] This Australian Standard was prepared

More information

Steel wire for general fencing purposes

Steel wire for general fencing purposes BRITISH STANDARD BS 4102:1998 ICS 77.140.65 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Specification for Steel wire for general fencing purposes Committees responsible for this

More information

This document is a preview generated by EVS

This document is a preview generated by EVS INTERNATIONAL STANDARD ISO 17636-1 First edition 2013-01-15 Non-destructive testing of welds Radiographic testing Part 1: X- and gamma-ray techniques with film Contrôle non destructif des assemblages soudés

More information

Australian Standard. ISO metric hexagon bolts and screws Product grades A and B. Part 1: Bolts AS ISO 4014:1999

Australian Standard. ISO metric hexagon bolts and screws Product grades A and B. Part 1: Bolts AS ISO 4014:1999 AS 1110.12000 ISO 4014:1999 AS 1110.1 Australian Standard ISO metric hexagon bolts and screws Product grades A and B Part 1: Bolts [ISO title: Hexagon head boltsproduct grades A and B] This Australian

More information

AS/NZS 1200:2000 AS/NZS

AS/NZS 1200:2000 AS/NZS AS/NZS 1200:2015 Australian/New Zealand Standard Pressure equipment Superseding AS/NZS 1200:2000 AS/NZS 1200:2015 AS/NZS 1200:2015 This joint Australian/New Zealand standard was prepared by joint Technical

More information

Non-destructive testing Image quality of radiographs. Part 2: Determination of the image quality value using step/hole-type image quality indicators

Non-destructive testing Image quality of radiographs. Part 2: Determination of the image quality value using step/hole-type image quality indicators INTERNATIONAL STANDARD ISO 19232-2 Second edition 2013-06-15 Non-destructive testing Image quality of radiographs Part 2: Determination of the image quality value using step/hole-type image quality indicators

More information

Radiographic testing: Increased detection sensitivity using optimum source to object distance

Radiographic testing: Increased detection sensitivity using optimum source to object distance 18 th World Conference on Non destructive Testing, 16-20 April 2012, Durban, South Africa Radiographic testing: Increased detection sensitivity using optimum source to object distance Jan Hendrik COWAN

More information

Australian Technical Specification

Australian Technical Specification ATS 4747.1 2008 ATS 4747.1 2008 Australian Technical Specification Meters for non-urban water supply Part 1: Glossary of terms This Australian Technical Specification was prepared by Committee CE-024,

More information

AS/NZS 1214:2016 Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series) AS/NZS 1214:2016

AS/NZS 1214:2016 Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series) AS/NZS 1214:2016 (ISO 10684:2004, MOD) Australian/New Zealand Standard Hot-dip galvanized coatings on threaded fasteners (ISO metric coarse thread series) AS/NZS 1214:2016 This joint Australian/New Zealand standard was

More information

Australian Standard. Acoustics Method for laboratory measurement of airborne sound transmission loss of building partitions AS

Australian Standard. Acoustics Method for laboratory measurement of airborne sound transmission loss of building partitions AS AS 1191 1985 Australian Standard Acoustics Method for laboratory measurement of airborne sound transmission loss of building partitions This Australian standard was prepared by Committee AK/4, Architectural

More information

Australian Standard. Safety of machinery. Part 1801: Safety distances to prevent danger zones being reached by the upper limbs AS 4024.

Australian Standard. Safety of machinery. Part 1801: Safety distances to prevent danger zones being reached by the upper limbs AS 4024. AS 4024.1801 2006 AS 4024.1801 2006 Australian Standard Safety of machinery Part 1801: Safety distances to prevent danger zones being reached by the upper limbs This Australian Standard was prepared by

More information

Australian Standard. Timber flooring. Part 2: Sanding and finishing AS AS

Australian Standard. Timber flooring. Part 2: Sanding and finishing AS AS AS 4786.2 2005 AS 4786.2 2005 Australian Standard Timber flooring Part 2: Sanding and finishing This Australian Standard was prepared by Committee TM-007, Sawn, milled and speciality timber products. It

More information

Australian Standard. High-voltage test techniques. Part 3: Definitions and requirements for on-site testing AS IEC , Ed.

Australian Standard. High-voltage test techniques. Part 3: Definitions and requirements for on-site testing AS IEC , Ed. AS 60060.3 2008 IEC 60060-3, Ed. 1 (2006) AS 60060.3 2008 Australian Standard High-voltage test techniques Part 3: Definitions and requirements for on-site testing This Australian Standard was prepared

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 4114.2 Australian/New Zealand Standard Spray painting booths, designated spray painting areas and paint mixing rooms Part 2: Installation and maintenance This Joint Australian/New Zealand Standard

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 3200.1.0:1998 Australian/New Zealand Standard Medical electrical equipment Part 1.0: General requirements for safety Parent Standard AS/NZS 3200.1.0:1998 This Joint Australian/New Zealand Standard

More information

Engineering Policy & Procedure

Engineering Policy & Procedure FPD > Engineering > Global Standards Engineering Policy & Procedure Revision History Number: G2-4 Section: G Subject: Radiographic Examination Procedure 1.0 SCOPE This procedure specifies the requirements

More information

Australian/New Zealand Standard

Australian/New Zealand Standard (Incorporating Amendment Nos 1 and 2) Australian/New Zealand Standard Radiocommunications equipment used in the UHF citizen band radio service This Joint Australian/New Zealand Standard was prepared by

More information

AS/NZS 4404:1996 AS/NZS

AS/NZS 4404:1996 AS/NZS (ISO 1482:2011, IDT) Australian/New Zealand Standard Slotted countersunk (flat) head tapping screws (common head style) Superseding AS/NZS 4404:1996 This joint Australian/New Zealand standard was prepared

More information

ISO metric hexagon bolts and screws Product grade C. Part 1: Bolts AS :2015 ISO 4016:2011

ISO metric hexagon bolts and screws Product grade C. Part 1: Bolts AS :2015 ISO 4016:2011 AS 1111.1:2015 ISO 4016:2011 AS 1111.1:2015 ISO metric hexagon bolts and screws Product grade C Part 1: Bolts This Australian Standard was prepared by Committee ME-029, Fasteners. It was approved on behalf

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 4677:2010 AS/NZS 4677:2010 Australian/New Zealand Standard Steel utility services poles AS/NZS 4677:2010 This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee CE-019,

More information

Metric sine bars and sine tables (excluding compound tables)

Metric sine bars and sine tables (excluding compound tables) BRITISH STANDARD BS 3064:1978 Specification for Metric sine bars and sine tables (excluding compound tables) UDC 621.753:531.745 Confirmed February 2012 Cooperating organizations The Mechanical Engineering

More information

Australian Standard. Wood processing machinery Safety. Part 5: Finishing machinery Moulding machines and routers with rotating tool AS 1473.

Australian Standard. Wood processing machinery Safety. Part 5: Finishing machinery Moulding machines and routers with rotating tool AS 1473. AS 1473.5 2001 AS 1473.5 Australian Standard Wood processing machinery Safety Part 5: Finishing machinery Moulding machines and routers with rotating tool This Australian Standard was prepared by Committee

More information

international Standard 1106/l

international Standard 1106/l international Standard 1106/l INTERNATIONAL ORGANIZATION FOR STANDARDIZATION~ME~KL(YHAPO~HAR OPI-AHkl3AL&lR ilo CTAHAAPTM3A~klkl.ORGANISATION INTERNATIONALE DE NORMALISATION Recommended practice for radiographic

More information

Licensed Copy: RRICTISQ RRICTISQ, ISO/Exchange Russia, 01 December 2004, Uncontrolled Copy, (c) BSI

Licensed Copy: RRICTISQ RRICTISQ, ISO/Exchange Russia, 01 December 2004, Uncontrolled Copy, (c) BSI BRITISH STANDARD BS EN 392:1995 Glued laminated timber Shear testof glue lines The European Standard EN 392:1995 has the status of a British Standard BSEN 392:1995 Committees responsible for this British

More information

AS/NZS :2011. Gate valves for waterworks purposes AS/NZS :2011. Part 2: Resilient seated. Australian/New Zealand Standard

AS/NZS :2011. Gate valves for waterworks purposes AS/NZS :2011. Part 2: Resilient seated. Australian/New Zealand Standard Incorporating Amendment No. 1 Australian/New Zealand Standard Gate valves for waterworks purposes Part 2: Resilient seated This joint Australian/New Zealand standard was prepared by joint Technical Committee

More information

Australian Standard. Electricity metering equipment (AC) Particular requirements

Australian Standard. Electricity metering equipment (AC) Particular requirements AS 62053.21 2005 AS 62053.21 2005 Australian Standard Electricity metering equipment (AC) Particular requirements Part 21: Static meters for active energy (classes 1 and 2) (IEC 62053-21, Ed.1.0 (2003)

More information

Plain bearings Wrapped bushes

Plain bearings Wrapped bushes BRITISH STANDARD BS ISO 3547-3:2006 Plain bearings Wrapped bushes Part 3: Lubrication holes, grooves and indentations ICS 21.100.10 National foreword This British Standard was published under the authority

More information

Plain bearings Wrapped bushes

Plain bearings Wrapped bushes BRITISH STANDARD BS ISO 3547-5:2007 Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI Plain bearings Wrapped bushes Part 5: Checking the outside diameter ICS 21.100.10 National foreword Licensed

More information

Non-destructive testing of welds Radiographic testing of welded joints

Non-destructive testing of welds Radiographic testing of welded joints BRITISH STANDARD Non-destructive testing of welds Radiographic testing of welded joints BS EN 1435:1997 Incorporating Corrigendum No. 1 and Amendments Nos. 1 and 2 The European Standard EN 1435:1997, with

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 61000.4.11:2005 AS/NZS 61000.4.11:2005 Australian/New Zealand Standard Electromagnetic compatibility (EMC) Part 4.11: Testing and measurement techniques Voltage dips, short interruptions and voltage

More information

Australian Standard. Design review AS IEC IEC 61160, Ed.2 (2005) AS IEC

Australian Standard. Design review AS IEC IEC 61160, Ed.2 (2005) AS IEC AS IEC 61160 2008 IEC 61160, Ed.2 (2005) AS IEC 61160 2008 Australian Standard Design review This Australian Standard was prepared by Committee QR-005, Dependability. It was approved on behalf of the Council

More information

BOLTS, SCREWS, NUTS AND PLAIN WASHERS

BOLTS, SCREWS, NUTS AND PLAIN WASHERS BRITISH STANDARD SPECIFICATION UNIFIED BLACK HEXAGON BOLTS, SCREWS, NUTS AND PLAIN WASHERS (UNC & UNF THREADS) B Te HEAVY SERIES B.S. 1769 : 1951 incorporating amendments issued March 1955 (PD 2141) May

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS CISPR 12:2009 CISPR 12, Ed.6.0 (2007) AS/NZS CISPR 12:2009 Australian/New Zealand Standard Vehicles, boats and internal combustion engines Radio disturbance characteristics Limits and methods of

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS IEC 61935.1:2006 IEC 61935-1:2005 AS/NZS IEC 61935.1:2006 Australian/New Zealand Standard Testing of balanced communication cabling in accordance with ISO/IEC 11801 Part 1: Installed cabling AS/NZS

More information

Film Replacement in Radiographic Weld Inspection The New ISO Standard

Film Replacement in Radiographic Weld Inspection The New ISO Standard BAM Berlin Film Replacement in Radiographic Weld Inspection The New ISO Standard 17636-2 Uwe Ewert, Uwe Zscherpel, Mirko Jechow Requests and information to: uwez@bam.de 1 Outline - The 3 essential parameters

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 61000.6.3:2007 IEC 61000-6-3, Ed. 2.0 (2006) AS/NZS 61000.6.3:2007 Australian/New Zealand Standard Electromagnetic compatibility (EMC) Part 6.3: Generic standards Emission standard for residential,

More information

This British Standard, having been prepared under the direction of the Iron and Steel Standards Policy Committee, was published under the authority of

This British Standard, having been prepared under the direction of the Iron and Steel Standards Policy Committee, was published under the authority of BRITISH STANDARD BS 5996:1993 Specification for Acceptance levels for internal imperfections in steel plate, strip and wide flats, based on ultrasonic testing UDC 669.14-41:620.179.16 This British Standard,

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 3439.2:2002 IEC 60439-2:2000 AS/NZS 3439.2 Australian/New Zealand Standard Low-voltage switchgear and controlgear assemblies Part 2: Particular requirements for busbar trunking systems (busways)

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 60076.3:2008 AS/NZS 60076.3:2008 Australian/New Zealand Standard Power transformers Part 3: Insulation levels, dielectric tests and external clearances in air (IEC 60076-3, Ed. 2 (2000) MOD) AS/NZS

More information

International Standard

International Standard International Standard INTERNATIONAL ORGANIZATION FOR STANDARDlZATION*MEXAYHAPO~HAR OPTAHM3ALWlR fl0 CTAH~APTM3ALWl~ORGANlSATlON INTERNATIONALE DE NORMALISATION Recommended practice for radiographic examination

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 60076.5:2012 AS/NZS 60076.5:2012 Australian/New Zealand Standard Power transformers Part 5: Ability to withstand short circuit (IEC 60076-5, Ed. 3.0 (2006) MOD) AS/NZS 60076.5:2012 This Joint Australian/New

More information

Interim Australian/New Zealand Standard

Interim Australian/New Zealand Standard Expires 31 December 2010 Interim Australian/New Zealand Standard Adhesives for timber and timber products Part 1: Adhesives for manufacture of plywood and laminated veneer lumber (LVL) This Joint Interim

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 2772.2:2011 AS/NZS 2772.2:2011 Australian/New Zealand Standard Radiofrequency fields Part 2: Principles and methods of measurement and computation 3 khz to 300 GHz AS/NZS 2772.2:2011 This Joint

More information

Non-destructive testing Radioscopic testing

Non-destructive testing Radioscopic testing BRITISH STANDARD BS EN 13068-3:2001 Non-destructive testing Radioscopic testing Part 3: General principles of radioscopic testing of metallic materials by X- and gamma rays The European Standard EN 13068-3:2001

More information

ISO INTERNATIONAL STANDARD

ISO INTERNATIONAL STANDARD INTERNATIONAL STANDARD ISO 16371-1 First edition 2011-10-01 Non-destructive testing Industrial computed radiography with storage phosphor imaging plates Part 1: Classification of systems Essais non destructifs

More information

Gamex Lite 3.0 Program description and operating manual

Gamex Lite 3.0 Program description and operating manual Gamex Lite 3.0 Program description and operating manual Issue No. : 3.0 Date of Issue : 12-2013 Z.U.T. NDT SOFT http://www.ndtsoft.eu Copyright (c) 2013 by Z.U.T. NDT SOFT All Rights Reserved Disclaimer

More information

Ergonomics The human factor A practical approach to work systems design

Ergonomics The human factor A practical approach to work systems design SAA HB59 1994 Handbook Ergonomics The human factor A practical approach to work systems design SAA HB59 1994 Handbook Ergonomics The human factor A practical approach to work systems design First published

More information

LICENCE. for WEB LINKS. Check if this document is current Find similar documents StandardsWatch (info and login) Visit our website

LICENCE. for WEB LINKS. Check if this document is current Find similar documents StandardsWatch (info and login) Visit our website LICENCE for Licensee: Date: Conditions of use: Click here for full conditions of Licence WEB LINKS Check if this document is current Find similar documents StandardsWatch (info and login) Visit our website

More information

AS/NZS :2014

AS/NZS :2014 AS/NZS 4024.1100:2014 Australian/New Zealand Standard Safety of machinery Part 1100: Application guide AS/NZS 4024.1100:2014 AS/NZS 4024.1100:2014 This joint Australian/New Zealand standard was prepared

More information

AS/NZS :2015. Methods of testing bitumen and related roadmaking products AS/NZS :2015

AS/NZS :2015. Methods of testing bitumen and related roadmaking products AS/NZS :2015 Australian/New Zealand Standard Methods of testing bitumen and related roadmaking products and air on a moving film of bitumen (rolling thin film oven (RTFO) test) Superseding AS/NZS 2341.10:1994 This

More information

Road signs Specifications

Road signs Specifications AS 1743:2018 AS 1743:2018 Road signs Specifications This Australian Standard was prepared by Committee MS-012, Road Signs and Traffic Signals. It was approved on behalf of the Council of Standards Australia

More information

Hot rolled square steel bars for general purposes Dimensions and tolerances on shape and dimensions

Hot rolled square steel bars for general purposes Dimensions and tolerances on shape and dimensions BRITISH STANDARD BS EN 10059:2003 Hot rolled square steel bars for general purposes Dimensions and tolerances on shape and dimensions The European Standard EN 10059:2003 has the status of a British Standard

More information

Ophthalmic optics Spectacle frames Requirements and test methods

Ophthalmic optics Spectacle frames Requirements and test methods (ISO 12870:2012 IDT) Australian/New Zealand Standard Ophthalmic optics Spectacle frames Requirements and test methods AS/NZS ISO 12870:2012 This Joint Australian/New Zealand Standard was prepared by Joint

More information

Australian Standard. Instrument transformers. Part 1: Current transformers (IEC Ed.1.2 (2003) MOD) AS AS

Australian Standard. Instrument transformers. Part 1: Current transformers (IEC Ed.1.2 (2003) MOD) AS AS AS 60044.1 2007 AS 60044.1 2007 Australian Standard Instrument transformers Part 1: Current transformers (IEC 60044-1 Ed.1.2 (2003) MOD) This Australian Standard was prepared by Committee EL-013, Measurement

More information

ISO INTERNATIONAL STANDARD. Non-destructive testing of welds Radiographic testing Part 2: X- and gamma-ray techniques with digital detectors

ISO INTERNATIONAL STANDARD. Non-destructive testing of welds Radiographic testing Part 2: X- and gamma-ray techniques with digital detectors INTERNATIONAL STANDARD ISO 17636-2 First edition 2013-01-15 Non-destructive testing of welds Radiographic testing Part 2: X- and gamma-ray techniques with digital detectors Contrôle non destructif des

More information

AS N4 Supplement

AS N4 Supplement AS 1684.2 N4 Supplement 2 2006 Residential timber-framed construction Part 2: Non-cyclonic areas N4 Supplement 2: Timber framing span tables Wind classification N4 Seasoned softwood Stress Grade F7 (Supplement

More information

AS/NZS ISO 9000:2016. Quality management systems Fundamentals and vocabulary AS/NZS ISO 9000:2016. Australian/New Zealand Standard

AS/NZS ISO 9000:2016. Quality management systems Fundamentals and vocabulary AS/NZS ISO 9000:2016. Australian/New Zealand Standard (ISO 9000:2015, IDT) Australian/New Zealand Standard Quality management systems Fundamentals and vocabulary Superseding AS/NZS ISO 9000:2006 AS/NZS ISO 9000:2016 This joint Australian/New Zealand standard

More information

AS/NZS CISPR 14.2:2015

AS/NZS CISPR 14.2:2015 AS/NZS CISPR 14.2:2015 (CISPR 14-2, Ed. 2.0:2015, IDT) Australian/New Zealand Standard Electromagnetic compatibility Requirements for household appliances, electric tools and similar apparatus Part 2:

More information

Australian/New Zealand Standard

Australian/New Zealand Standard Australian/New Zealand Standard Methods of test for pulp and paper Method 431rp: Taber bending resistance of paper and paperboard This Joint Australian/New Zealand Standard was prepared by Joint Technical

More information

ISO 7004 INTERNATIONAL STANDARD

ISO 7004 INTERNATIONAL STANDARD INTERNATIONAL STANDARD ISO 7004 Second edition 2002-10-01 Photography Industrial radiographic films Determination of ISO speed, ISO average gradient and ISO gradients G2 and G4 when exposed to X- and gamma-radiation

More information

RADIOGRAPHIC EXAMINATION PROCEDURE

RADIOGRAPHIC EXAMINATION PROCEDURE Page 1 of 19 Doc. No. KNS/RT/01.REV 0 RADIOGRAPHIC EXAMINATION PROCEDURE Page: 19 of 19 Date: 15.09.2012 RADIOGRAPHIC EXAMINATION PROCEDURE PREPARED & APPROVED BY NDE- Level III CERTIFIED BY REVIEWED BY

More information

Equivalent Penetrameter Sensitivity (EPS) for Performance Evaluation of Computed Radiography Systems Muzibur Khan * and Mike Brothers

Equivalent Penetrameter Sensitivity (EPS) for Performance Evaluation of Computed Radiography Systems Muzibur Khan * and Mike Brothers Equivalent Penetrameter Sensitivity (EPS) for Performance Evaluation of Computed Radiography Systems Muzibur Khan * and Mike Brothers More info about this article: http://www.ndt.net/?id=22782 Abstract

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 1337.0:2014 Australian/New Zealand Standard Personal eye protection Part 0: Eye and face protection Vocabulary (ISO 4007:2012, MOD) This Joint Australian/New Zealand Standard was prepared by Joint

More information

AS/NZS :2013

AS/NZS :2013 AS/NZS 61000.3.2:2013 IEC 61000-3-2, Ed. 3.2 2009, MOD (NZ) Australian/New Zealand Standard Electromagnetic compatibility (EMC) Part 3.2: Limits Limits for harmonic current emissions (equipment input current

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS CISPR 15:2011 AS/NZS CISPR 15:2011 Australian/New Zealand Standard Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment (CISPR 15,

More information

Welding Inspection Non-Destructive Testing Course Reference WIS 5

Welding Inspection Non-Destructive Testing Course Reference WIS 5 Welding Inspection Non-Destructive Testing Course Reference WIS 5 Non Destructive Testing A welding inspector should have a working knowledge of NDT methods and their applications, advantages and disadvantages.

More information

AS/NZS :2017. Electrical installations Selection of cables AS/NZS :2017

AS/NZS :2017. Electrical installations Selection of cables AS/NZS :2017 Australian/New Zealand Standard Electrical installations Selection of cables AS/NZS 3008.1.1:2017 Part 1.1: Cables for alternating voltages up to and including 0.6/1 kv Typical Australian installation

More information

Australian/New Zealand Standard

Australian/New Zealand Standard AS/NZS 4768.1:2010 AS/NZS 4768.1:2010 Australian/New Zealand Standard Digital radio equipment operating in land mobile and fixed services bands in the frequency range 29.7 MHz to 1 GHz Part 1: Radiofrequency

More information

ISO INTERNATIONAL STANDARD. Non-destructive testing Qualification of radiographic film digitisation systems Part 2: Minimum requirements

ISO INTERNATIONAL STANDARD. Non-destructive testing Qualification of radiographic film digitisation systems Part 2: Minimum requirements INTERNATIONAL STANDARD ISO 14096-2 First edition 2005-06-15 Non-destructive testing Qualification of radiographic film digitisation systems Part 2: Minimum requirements Essais non destructifs Qualification

More information

PRACTICAL CONSIDERATIONS AND EFFECTS OF METALLIC SCREEN FLUORESCENCE AND BACKSCATTER CONTROL IN GAMMA COMPUTED RADIOGRAPHY

PRACTICAL CONSIDERATIONS AND EFFECTS OF METALLIC SCREEN FLUORESCENCE AND BACKSCATTER CONTROL IN GAMMA COMPUTED RADIOGRAPHY 19 th World Conference on Non-Destructive Testing 2016 PRACTICAL CONSIDERATIONS AND EFFECTS OF METALLIC SCREEN FLUORESCENCE AND BACKSCATTER CONTROL IN GAMMA COMPUTED RADIOGRAPHY Steven MANGO 1 1 Carestream

More information

AS/NZS CISPR 14.1:2013

AS/NZS CISPR 14.1:2013 AS/NZS CISPR 14.1:2013 CISPR 14-1, Ed.5.2 2011, IDT Australian/New Zealand Standard Electromagnetic compatibility Requirements for household appliances, electric tools and similar apparatus Part 1: Emission

More information

AS/NZS IEC :2013

AS/NZS IEC :2013 AS/NZS IEC 61000.4.2:2013 IEC 61000-4-2, Ed.2.0 2008, IDT Australian/New Zealand Standard Electromagnetic compatibility (EMC) Part 4.2: Testing and measurement techniques Electrostatic discharge immunity

More information

ISO INTERNATIONAL STANDARD

ISO INTERNATIONAL STANDARD INTERNATIONAL STANDARD ISO 12096 First edition 1996-05-01 Submerged arc-welded steel tubes for pressure purposes - Radiographit testing of the weld seam for the detection of imperfections Tubes en acier

More information

ISO INTERNATIONAL STANDARD. Technical product documentation Digital product definition data practices

ISO INTERNATIONAL STANDARD. Technical product documentation Digital product definition data practices INTERNATIONAL STANDARD ISO 16792 First edition 2006-12-15 Technical product documentation Digital product definition data practices Documentation technique de produits Données de définition d'un produit

More information

NON-DESTRUCTIVE EVALUATION UTILIZING IMAGING PLATES FOR FIELD RADIOGRAPHY APPLICATIONS

NON-DESTRUCTIVE EVALUATION UTILIZING IMAGING PLATES FOR FIELD RADIOGRAPHY APPLICATIONS 19 th World Conference on Non-Destructive Testing 2016 NON-DESTRUCTIVE EVALUATION UTILIZING IMAGING PLATES FOR FIELD RADIOGRAPHY APPLICATIONS Brian S. WHITE 1 1 Carestream NDT, 1049 Ridge Road West, Rochester,

More information