Job Sheet 3. Using the Machine Vision System OBJECTIVE PROCEDURE. Setup and connections

Size: px
Start display at page:

Download "Job Sheet 3. Using the Machine Vision System OBJECTIVE PROCEDURE. Setup and connections"

Transcription

1 Job Sheet 3 Using the Machine Vision System OBJECTIVE Install the Machine Vision System on the Flexible Manufacturing System and use it to perform quality control on the boxes filled with marbles. PROCEDURE Setup and connections 1. Perform the basic safety procedures listed in Appendix B of this manual. a Refer to the Equipment Utilization Chart in Appendix A of the manual to obtain the list of equipment required to complete this Job Sheet. Festo Didactic

2 2. Connect the equipment as shown in the wiring diagram presented in Figure 37 or Figure 38, depending on your PLC version ( or 5930-A). Figure 37. Using the Machine Vision System wiring diagram ( PLC). 34 Festo Didactic

3 a Figure 38. Using the Machine Vision System wiring diagram (5930-A PLC). PoE (Power over Ethernet) refers to a technology that allows the passing of electrical power through Ethernet cabling, along with the regular data. Festo Didactic

4 a Make sure the AC Drive Start Source parameter (P036) is set to 5 (Comm Port). 3. Make the pneumatic connections according to the diagram presented in Figure 39. Pneumatic Box Feeder 5911 Push rod Pneumatic Sorting Device 5913 Stopper Lateral cylinder Directional Control Valve Station 5914 V1 V2 V3 V4 Safety Valve 6494 Conditioning Unit 6411-A Figure 39. Using the Machine Vision System pneumatic connections diagram. Be sure to adjust the pressure in the circuit downstream from the valve of the Conditioning Unit to 138 kpa (or 20 psi). 36 Festo Didactic

5 4. Fill the Part Feeder using marbles of two different colors. Use black marbles in the first hopper and blue marbles in the second hopper, as shown in Figure 40. Also, make sure to use white boxes. A light background allows a greater contrast in the picture taken by the camera. First hopper Second hopper a Figure 40. Filling the Part Feeder s hoppers. To keep marbles from getting stuck in the Part Feeder mechanism, do not overfill the hoppers. Festo Didactic

6 5. Install the camera on the mast and position it at the right of the Part Feeder, as shown in Figure 41. Figure 41. Positioning the camera on the FMS. 38 Festo Didactic

7 6. Be sure to position the sensors as shown in Figure B B B B B0 Figure 42. Sensors position. Festo Didactic

8 7. Once completed, the setup should look as shown in Figure 43. Figure 43. Using the Machine Vision System setup. 8. Turn on the computer, the switch, and the PLC. The emergency push-button must be released. 9. Open RSLinx and verify that Ethernet communication with the PLC works correctly using RSWho. 10. Make sure that the PLC key is in the REM position. Start RSLogix Open the PLC program for your particular PLC model (L32E or L43) and download it to the PLC. 11. Put the PLC to Remote Run mode but do not press any button yet so that the conveyor remains static. 40 Festo Didactic

9 12. Press the red push-button on the Indicator Light/Push-Button Station to power the drive and the Part Feeder. Make sure the AC Drive (01) and the Part Feeder (02) are scanned by the PLC DeviceNet scanner using RSNetWorx. For DeviceNet configuration details, refer to the Introduction to Manufacturing manual (P/N ). Configuration of the Machine Vision System 13. Start In-Sight Explorer. If the camera does not appear in the list of In-Sight Sensors, select Add Sensor/Device To Network in the System menu. Select the sensor (ism1020) in the network, then click Apply to close this window. 14. Connect to the camera but put it offline (click on the button if necessary). 15. Four pre-configured job files are provided on the Resource Kit DVD-ROM. Open the one entitled WA_3BK1BL.job. This job is made for white boxes and a recipe of 3 black marbles and 1 blue marble. Festo Didactic

10 Tuning the Machine Vision System 16. Place a box filled with 3 black marbles and 1 blue marble right under the camera and press the Trigger ( ) button. You should obtain an image similar to Figure 44 in In-Sight Explorer. Align the tools regions of interest over the box edges by adjusting the camera vertical and horizontal position. You may have to make several tests to adjust the position of the camera correctly. Figure 44. Picture of a box with 4 marbles. 42 Festo Didactic

11 17. If the edges of the marbles are not sharp on the pictures (Figure 45), rotate the lens barrel to adjust the camera focus. Figure 45. Blurred picture. 18. The list of the different tools that compose the WA_3BK1BL job is located in the Palette section (at the right of the screen) under the Results tab (Figure 46). Figure 46. Job Results (WA_3BK1BL). Festo Didactic

12 The Edge_Bottom tool finds the bottom of the box in the image with the help of the Filter_Bottom tool that does point filtering in the area where Edge_Bottom is looking for an edge. The filter makes every pixel either black (0) or white (255) depending if it is above or below the Threshold value. The edge found then serves as Tool Fixture for the other tools. Pixel_Black is a tool that counts the number of dark pixels and returns a Pass result if this number falls between the minimum and maximum range limits. These limits are adjusted for the expected black pixels generated by the presence of three black marbles. Filter_Grey is a point filter that makes grey pixels turn black and other pixels turn white. The purpose of this tool is to make black marbles disappear. However, the contours of the black marbles remain. The Filter_Grey_Closing tool removes these contours, so that only blobs from grey marbles remain. Blobs_Grey returns a Pass result if it detects one blob. 19. If your image is not set properly, the image obtained can return a Fail result, even if the right number of marbles is in the box. In the example of Figure 47, the image is too clear, causing Pixel_Black to fail. Figure 47. Image too clear (Pixels_Black fails). 44 Festo Didactic

13 If this happens, you can modify the camera exposure time. Go to View Application Steps Set Up Image and change the Exposure (msec) parameter (Figure 48). If your lighting conditions change, you may need to adjust the camera exposure time or the tools parameters from time to time. Figure 48. Editing camera exposure time. 20. Take pictures with different combinations of marbles (e.g., 2 black and 2 blue) to check the robustness of your tools. Adjust the tools parameters (e.g., Ranges) if necessary. 21. Before going online, verify that the strobe is set correctly. At the bottom of the Outputs section, set the signal type for output Direct 1 to Strobe. Click on Details, then set the Strobe/Light Control Trigger parameter to Falling Edge and the Strobe Start Position parameter to Acquisition Start. Using the Vision System with the FMS in motion 22. Click on the button to put the camera online. You are now ready to perform a test run on the FMS with the actual Machine Vision System configuration. Since it is the first time that you start the whole system, be prepared to stop it to make some adjustments. 23. Press the green push-button on the Indicator Light/Push-Button Station to start the system. If necessary, adjust the INSPECTION sensor to trigger the camera when boxes are in front of it. 24. Readjust the exposure time or the tools parameters until you always get a Pass result when a box containing the correct arrangement of marbles is inspected and a Fail result when a box is improperly filled. Festo Didactic

14 25. Test the FMS. If the system is properly tuned, boxes containing the correct recipe are directed to trays 1 and 2, while the other boxes are directed to the end tray, as shown in Figure 49. Tray 1 End tray Tray 2 Figure 49. Boxes sorted in the tray of the FMS. A video of the setup presented in this Job Sheet is available on the Flexible Manufacturing System Resource Kit (student) DVD-ROM. 26. Ask your instructor to check and approve your work. Troubleshooting exercise a Prior to this exercise, the instructor must insert a fault into the FMS circuit. 46 Festo Didactic

15 27. Try to use the setup and check if everything is working properly. If the system is not working properly, describe the symptom(s). 28. Use your troubleshooting skills to identify the malfunctioning module(s) and isolate the problem(s). 29. Explain in detail your approach to isolating the problem. 30. Ask your instructor to check and approve your work. Name: Date: Instructor's approval: Festo Didactic

Introduction to the Camera Software Part 1

Introduction to the Camera Software Part 1 Exercise 1 Introduction to the Camera Software Part 1 EXERCISE OBJECTIVE In-Sight Explorer DISCUSSION OUTLINE DISCUSSION Software tools to detect objects a You can see a job as an exam and a tool as a

More information

ivu Series TG Image Sensor

ivu Series TG Image Sensor Quick Start Guide Introduction The ivu Series Image Sensor is used to monitor labels, parts, and packaging for type, size, orientation, shape, and location. The sensor has an integrated color touch screen

More information

Versatile Camera Machine Vision Lab

Versatile Camera Machine Vision Lab Versatile Camera Machine Vision Lab In-Sight Explorer 5.6.0-1 - Table of Contents Pill Inspection... Error! Bookmark not defined. Get Connected... Error! Bookmark not defined. Set Up Image... - 8 - Location

More information

ivu Plus Quick Start Guide P/N rev. A -- 10/8/2010

ivu Plus Quick Start Guide P/N rev. A -- 10/8/2010 P/N 154721 rev. A -- 10/8/2010 Contents Contents 1 Introduction...3 2 ivu Plus Major Features...4 2.1 Demo Mode...4 2.2 Sensor Types...4 2.2.1 Selecting a Sensor Type...5 2.3 Multiple Inspections...6 2.3.1

More information

Determining the Dynamic Characteristics of a Process

Determining the Dynamic Characteristics of a Process Exercise 1-1 Determining the Dynamic Characteristics of a Process EXERCISE OBJECTIVE Familiarize yourself with three methods to determine the dynamic characteristics of a process. DISCUSSION OUTLINE The

More information

Exercise 8. Troubleshooting a Radar Target Tracker EXERCISE OBJECTIVE

Exercise 8. Troubleshooting a Radar Target Tracker EXERCISE OBJECTIVE Exercise 8 Troubleshooting a Radar Target Tracker EXERCISE OBJECTIVE When you have completed this exercise, you will be able to apply an efficient troubleshooting procedure in order to locate instructor-inserted

More information

LEARNING ACTIVITY PACKET MECHATRONICS MULTIPLE STATION CONTROL B72001-AA10UEN

LEARNING ACTIVITY PACKET MECHATRONICS MULTIPLE STATION CONTROL B72001-AA10UEN MECHATRONICS LEARNING ACTIVITY PACKET MULTIPLE CONTROL B72001-AA10UEN LEARNING ACTIVITY PACKET 10 MULTIPLE CONTROL INTRODUCTION To manufacture most products requires a number of steps that have to be performed.

More information

Models included: GEO EDGE

Models included: GEO EDGE Models included: GEO EDGE Printed in USA 12/04 P/N 118000 rev. A WARNING... Not To Be Used for Personnel Protection Never use this product as a sensing device for personnel protection. Doing so could lead

More information

Screwfeeder Troubleshooting Guide

Screwfeeder Troubleshooting Guide Symptom General Cause Specific Cause Solution Illustration No Screws are being fed to the screwdriver Screw jam in screw delivery tubing Insufficient Screw Blast to deliver screw Adjust Screw Blast Inline

More information

Vinyl Cutter Instruction Manual

Vinyl Cutter Instruction Manual Vinyl Cutter Instruction Manual 1 Product Inventory Inventory Here is a list of items you will receive with your vinyl cutter: Product components (Fig.1-4): 1x Cutter head unit complete with motor, plastic

More information

Welcome to Polaroid PhotoMAX FUN!

Welcome to Polaroid PhotoMAX FUN! Contents Welcome to Polaroid PhotoMAX FUN!...................... 1 The Polaroid PhotoMAX FUN! Digital 320 Creative Kit......... 2 Kit components......................................... 3 Polaroid Digital

More information

Acceleration and Deceleration Control

Acceleration and Deceleration Control Exercise 2 Acceleration and Deceleration Control EXERCISE OBJECTIVE To learn how to eliminate abrupt starting and stopping of an actuator with acceleration and deceleration control. DISCUSSION Acceleration

More information

TRDB_DC2 TRDB_DC2. 1.3Mega Pixel Digital Camera Development Kit

TRDB_DC2 TRDB_DC2. 1.3Mega Pixel Digital Camera Development Kit Terasic TRDB_DC2 Digital Camera Package TRDB_DC2 1.3Mega Pixel Digital Camera Development Kit Frame grabber with VGA display reference design For Altera DE2 and Terasic T-Rex C1 Boards TRDB_DC2 Document

More information

Brightness and Contrast Control Reference Guide

Brightness and Contrast Control Reference Guide innovation Series Scanners Brightness and Contrast Control Reference Guide A-61506 Part No. 9E3722 CAT No. 137 0337 Using the Brightness and Contrast Control This Reference Guide provides information and

More information

The Discussion of this exercise covers the following points: Differential-pressure transmitter. Differential-pressure transmitter

The Discussion of this exercise covers the following points: Differential-pressure transmitter. Differential-pressure transmitter Exercise 2-1 Two-Wire Transmitter EXERCISE OBJECTIVE Become familiar with HART point-to-point connection of a two-wire transmitter. DISCUSSION OUTLINE The Discussion of this exercise covers the following

More information

FIRST Robotics Control System

FIRST Robotics Control System 2018/2019 FIRST Robotics Control System Team 236 1 (click on a component to go to its slide) 2 The Robot Powered solely by 12V battery RoboRIO- is the computer on the robot Controlled by Java code on the

More information

CALIBRATION MANUAL. Version Author: Robbie Dowling Lloyd Laney

CALIBRATION MANUAL. Version Author: Robbie Dowling Lloyd Laney Version 1.0-1012 Author: Robbie Dowling Lloyd Laney 2012 by VirTra Inc. All Rights Reserved. VirTra, the VirTra logo are either registered trademarks or trademarks of VirTra in the United States and/or

More information

Calibration. Click Process Images in the top right, then select the color tab on the bottom right and click the Color Threshold icon.

Calibration. Click Process Images in the top right, then select the color tab on the bottom right and click the Color Threshold icon. Calibration While many of the numbers for the Vision Processing code can be determined theoretically, there are a few parameters that are typically best to measure empirically then enter back into the

More information

Exercise 2-6. Target Bearing Estimation EXERCISE OBJECTIVE

Exercise 2-6. Target Bearing Estimation EXERCISE OBJECTIVE Exercise 2-6 EXERCISE OBJECTIVE When you have completed this exercise, you will be able to evaluate the position of the target relative to a selected beam using the A-scope display. You will be able to

More information

Visioneer OneTouch Scanner. Installation Guide FOR WINDOWS

Visioneer OneTouch Scanner. Installation Guide FOR WINDOWS Visioneer OneTouch Scanner Installation Guide FOR WINDOWS TABLE OF CONTENTS i TABLE OF CONTENTS Getting Started with your new Scanner....................... 1 Step 1: Installing the Scanner Software.......................

More information

Models included: GEO/GEO 1.3 EDGE/EDGE 1.3 BCR/BCR 1.3 AREA/AREA 1.3 OMNI/OMNI 1.3

Models included: GEO/GEO 1.3 EDGE/EDGE 1.3 BCR/BCR 1.3 AREA/AREA 1.3 OMNI/OMNI 1.3 Models included: GEO/GEO 1.3 EDGE/EDGE 1.3 BCR/BCR 1.3 AREA/AREA 1.3 OMNI/OMNI 1.3 Printed in USA 12/04 02/06 P/N 118000 rev. DA WARNING... Not To Be Used for Personnel Protection Never use this product

More information

Ambir ImageScan Pro 930u. User Guide. High Speed Document Scanner with UltraSonic Misfeed Detection. Ver 1.2. p/n UG930u-1.

Ambir ImageScan Pro 930u. User Guide. High Speed Document Scanner with UltraSonic Misfeed Detection.   Ver 1.2. p/n UG930u-1. Ambir ImageScan Pro 930u High Speed Document Scanner with UltraSonic Misfeed Detection www.ambir.com Ver 1.2 Ambir ImageScanPro 930u Table of Contents Box Contents Installation and Setup Loading Documents

More information

TROUBLE-SHOOTING: Error States

TROUBLE-SHOOTING: Error States TROUBLE-SHOOTING: Error States Please note, there is much commonality between the different models of LabelStation and therefore it is advisable to read the comments on other models if you cannot find

More information

Quick Start Overview. Related Information. In addition, the sensor includes integrated Help.

Quick Start Overview. Related Information. In addition, the sensor includes integrated Help. Quick Start Guide Introduction The ivu Plus TG Series sensor is used to monitor labels, parts, and packaging for type, size, orientation, shape, and location. The sensor has an integrated or remote color

More information

i1800 Series Scanners

i1800 Series Scanners i1800 Series Scanners Scanning Setup Guide A-61580 Contents 1 Introduction................................................ 1-1 About this manual........................................... 1-1 Image outputs...............................................

More information

Exercise 8. The Four-Quadrant Chopper EXERCISE OBJECTIVE DISCUSSION OUTLINE DISCUSSION. The Four-Quadrant Chopper

Exercise 8. The Four-Quadrant Chopper EXERCISE OBJECTIVE DISCUSSION OUTLINE DISCUSSION. The Four-Quadrant Chopper Exercise 8 The Four-Quadrant Chopper EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with the operation of the four-quadrant chopper. DISCUSSION OUTLINE The Discussion of

More information

Exercise 7. The Buck/Boost Chopper EXERCISE OBJECTIVE DISCUSSION OUTLINE DISCUSSION. The Buck/Boost Chopper

Exercise 7. The Buck/Boost Chopper EXERCISE OBJECTIVE DISCUSSION OUTLINE DISCUSSION. The Buck/Boost Chopper Exercise 7 The Buck/Boost Chopper EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with the operation of the buck/boost chopper. DISCUSSION OUTLINE The Discussion of this

More information

Exercise 4-1. Chaff Clouds EXERCISE OBJECTIVE

Exercise 4-1. Chaff Clouds EXERCISE OBJECTIVE Exercise 4-1 Chaff Clouds EXERCISE OBJECTIVE To demonstrate chaff as a method of denying target information to a radar. To verify whether MTI processing is an effective anti-chaff processing technique

More information

Using the Large Linear Verification Kit

Using the Large Linear Verification Kit Quick Start Guide Using the Large Linear Verification Kit Purpose This document provides guidance to users of the Large Linear Verification Kit, part number SLN-0000006. The kit consists of a light, bracket,

More information

Smart Vision Sensor INSTRUCTION MANUAL

Smart Vision Sensor INSTRUCTION MANUAL Smart Vision Sensor INSTRUCTION MANUAL DATALOGIC AUTOMATION Via Lavino 265-40050 Monte S.Pietro - Bologna Italy Tel: +39 051 6765611- Fax: +39 051 6759324 www.automation.datalogic.com e-mail: info.automation.it@datalogic.com

More information

inphoto ID Canon camera control software Automatic ID photography User Guide

inphoto ID Canon camera control software Automatic ID photography User Guide inphoto ID Canon camera control software Automatic ID photography User Guide 2008 Akond company 197342, Russia, St.-Petersburg, Serdobolskaya, 65A Phone/fax: +7(812)600-6918 Cell: +7(921)757-8319 e-mail:

More information

MX-2700N MX-3500N MX-3501N MX-4500N MX-4501N. Copier Guide

MX-2700N MX-3500N MX-3501N MX-4500N MX-4501N. Copier Guide MODEL: MX-2300N MX-2700N MX-3500N MX-350N MX-4500N MX-450N Copier Guide TABLE OF CONTENTS ABOUT THIS MANUAL........................ 3 MANUALS PROVIDED WITH THE MACHINE... 3 BASIC PROCEDURE FOR MAKING COPIES

More information

Instruction Manual for HyperScan Spectrometer

Instruction Manual for HyperScan Spectrometer August 2006 Version 1.1 Table of Contents Section Page 1 Hardware... 1 2 Mounting Procedure... 2 3 CCD Alignment... 6 4 Software... 7 5 Wiring Diagram... 19 1 HARDWARE While it is not necessary to have

More information

Solving Simple AC Circuits Using Circuit Impedance Calculation

Solving Simple AC Circuits Using Circuit Impedance Calculation Exercise 4-1 Solving Simple AC Circuits Using Circuit Impedance Calculation EXERCISE OBJECTIVE When you have completed this exercise, you will be able to resolve simple parallel and series ac circuits

More information

PC Eyebot. Tutorial PC-Eyebot Console Explained

PC Eyebot. Tutorial PC-Eyebot Console Explained Sightech Vision Systems, Inc. PC Eyebot Tutorial PC-Eyebot Console Explained Published 2005 Sightech Vision Systems, Inc. 6580 Via del Oro San Jose, CA 95126 Tel: 408.282.3770 Fax: 408.413-2600 Email:

More information

ToupSky Cameras Quick-guide

ToupSky Cameras Quick-guide ToupSky Cameras Quick-guide ToupSky is a capture and processing software offered by Touptek, the original manufacturer of the Toupcamera series. These are video cameras that offer live image capture for

More information

The Discussion of this exercise covers the following points:

The Discussion of this exercise covers the following points: Exercise 3-2 Frequency-Modulated CW Radar EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with FM ranging using frequency-modulated continuous-wave (FM-CW) radar. DISCUSSION

More information

The ideal K-12 science microscope solution. User Guide. for use with the Nova5000

The ideal K-12 science microscope solution. User Guide. for use with the Nova5000 The ideal K-12 science microscope solution User Guide for use with the Nova5000 NovaScope User Guide Information in this document is subject to change without notice. 2009 Fourier Systems Ltd. All rights

More information

KoPa Scanner. User's Manual A99. Ver 1.0. SHENZHEN OSTEC OPTO-ELECTRONIC TECHNOLOGY CO.,LTD.

KoPa Scanner. User's Manual A99. Ver 1.0. SHENZHEN OSTEC OPTO-ELECTRONIC TECHNOLOGY CO.,LTD. KoPa Scanner A99 User's Manual Ver 1.0 SHENZHEN OSTEC OPTO-ELECTRONIC TECHNOLOGY CO.,LTD. http://www.ostec.com.cn Content Chapter 1 Start... 1 1.1 Safety Warnings and Precautions... 1 1.2 Installation

More information

DATAVS2 series.

DATAVS2 series. VISION SENSORS DATAVS2 series The DATAVS2 vision sensor series presents all the characteristics able to solve artificial machine vision applications in a flexible and intuitive way. DATAVS2 is a completely

More information

Digital Portable Overhead Document Camera LV-1010

Digital Portable Overhead Document Camera LV-1010 Digital Portable Overhead Document Camera LV-1010 Instruction Manual 1 Content I Product Introduction 1.1 Product appearance..3 1.2 Main functions and features of the product.3 1.3 Production specifications.4

More information

Studuino Icon Programming Environment Guide

Studuino Icon Programming Environment Guide Studuino Icon Programming Environment Guide Ver 0.9.6 4/17/2014 This manual introduces the Studuino Software environment. As the Studuino programming environment develops, these instructions may be edited

More information

Servo Robot Training Systems

Servo Robot Training Systems Servo Robot Training Systems LabVolt Series Datasheet Festo Didactic en 220 V - 50 Hz 07/2018 Table of Contents General Description 2 Robot Controller Module 3 Servo Robot Software 3 Location Pins 4 Included

More information

FOUNDATION Fieldbus Device Configuration

FOUNDATION Fieldbus Device Configuration Process Control FOUNDATION Fieldbus Device Configuration Courseware Sample 86002-F0 Order no.: 86002-10 First Edition Revision level: 02/2015 By the staff of Festo Didactic Festo Didactic Ltée/Ltd, Quebec,

More information

Sorting Line with Detection 9V

Sorting Line with Detection 9V 536628 Sorting Line with Detection 9V I2 O8 I1 I3 C1 I5 I6 I4 Not in the picture: O5, O6, O7, O8 Circuit layout for Sorting Line with Detection Terminal no. Function Input/Output 1 color sensor I1 2 phototransistor

More information

APNT#1166 Banner Engineering Driver v How To Guide

APNT#1166 Banner Engineering Driver v How To Guide Application Note #1166: Banner Engineering Driver v1.10.02 How To Guide Introduction This Application Note is intended to assist users in using the GP-Pro EX Version 2..X\2.10.X Banner Engineering Corp.

More information

BASIC IMAGE RECORDING

BASIC IMAGE RECORDING BASIC IMAGE RECORDING BASIC IMAGE RECORDING This section describes the basic procedure for recording an image. Recording an Image Aiming the Camera Use both hands to hold the camera still when shooting

More information

Veterinary Digital X-Ray System Quick Start Guide

Veterinary Digital X-Ray System Quick Start Guide 1 Veterinary Digital X-Ray System Quick Start Guide 2 SOPIX² X-Ray Sensors Quick Start Guide ***PERFORM THIS STEP BEFORE PLUGGING IN THE SENSOR*** Step 1 Load the CD: If you have already plugged in the

More information

The Discussion of this exercise covers the following points: Introduction How a tuning fork works Industrial applications. How a tuning fork works

The Discussion of this exercise covers the following points: Introduction How a tuning fork works Industrial applications. How a tuning fork works Exercise 3 Vibrating Level Switch EXERCISE OBJECTIVE Learn the working principle of vibrating level switches and learn how to use the vibrating level switch, Model 46933. DISCUSSION OUTLINE The Discussion

More information

The CReSIS Anechoic Chamber is located at: The University of Kansas. M2SEC building W 15 th St. Lawrence, KS

The CReSIS Anechoic Chamber is located at: The University of Kansas. M2SEC building W 15 th St. Lawrence, KS The CReSIS Anechoic Chamber is located at: The University of Kansas M2SEC building 1536 W 15 th St Lawrence, KS 66045 Pattern Manual Antenna radiation pattern measurement 1. To open EMQuest, right click

More information

User Manual. User Manual. Version Last change : March Page 1 ID station User Manual

User Manual. User Manual. Version Last change : March Page 1 ID station User Manual User Manual Version 7.4.3 Last change : March 2017 Page 1 Introduction This is the user manual of the new fastid, the biometric ID and passport photo system. This user guide helps you in everyday use.

More information

efector dualis Vision Sensor Part verification for error-proofing efector dualis Vision Sensor Product / Application Guide

efector dualis Vision Sensor Part verification for error-proofing efector dualis Vision Sensor Product / Application Guide efector dualis Vision Sensor Part verification for error-proofing Contour matching Orientation Part presence efector dualis Vision Sensor Product / Application Guide 3 Product Introduction efector dualis

More information

5250 Servo Robot Training Systems

5250 Servo Robot Training Systems 5250 Servo Robot Training Systems LabVolt Series Datasheet Festo Didactic en 120 V - 60 Hz 02/2018 Table of Contents General Description 2 Robot Controller Module 3 Servo Robot Software 3 Location Pins

More information

Training Calendar 2018

Training Calendar 2018 Training Calendar 2018 Training and seminars from industry - for industry www.festo-didactic.com/in-en Didactic Training for the industry Photo: WorldSkills, Abu Dhabi The relentless competitive pressure

More information

100/140 Series. 2D Data Matrix Specifications

100/140 Series. 2D Data Matrix Specifications 100/140 Series 2D Data Matrix Specifications Table of Contents 1 Introduction... 2 2 2D Label Specification and Position... 2 3 DS140 Datamatrix 2D Scanner Engineer Test Mode... 3 3.1 Interfacing a PC

More information

ArduCAM USB Camera Shield

ArduCAM USB Camera Shield ArduCAM USB Camera Shield Application Note for MT9V034 Rev 1.0, June 2017 Table of Contents 1 Introduction... 2 2 Hardware Installation... 2 3 Run the Demo... 3 4 Tune the Sensor Registers... 4 4.1 Identify

More information

AutoSeal FD 2006IL / FE 2006IL

AutoSeal FD 2006IL / FE 2006IL AutoSeal FD 2006IL / FE 2006IL FI / FJ Series 06/2018 OPERATOR MANUAL First Edition TABLE OF CONTENTS DESCRIPTION 1 SPECIFICATIONS 1 UNPACKING 1 SETUP 2 Sealer Alignment Base Setup 2 Sealer Setup 2-4

More information

Exercise 1-5. Antennas in EW: Sidelobe Jamming and Space Discrimination EXERCISE OBJECTIVE

Exercise 1-5. Antennas in EW: Sidelobe Jamming and Space Discrimination EXERCISE OBJECTIVE Exercise 1-5 Antennas in EW: Sidelobe Jamming EXERCISE OBJECTIVE To demonstrate that noise jamming can be injected into a radar receiver via the sidelobes of the radar antenna. To outline the effects of

More information

R I T. Title: Wyko RST Plus. Semiconductor & Microsystems Fabrication Laboratory Revision: A Rev Date: 05/23/06 1 SCOPE 2 REFERENCE DOCUMENTS

R I T. Title: Wyko RST Plus. Semiconductor & Microsystems Fabrication Laboratory Revision: A Rev Date: 05/23/06 1 SCOPE 2 REFERENCE DOCUMENTS Approved by: Process Engineer / / / / Equipment Engineer 1 SCOPE The purpose of this document is to detail the use of the Wyko RST Plus. All users are expected to have read and understood this document.

More information

GlassSpection User Guide

GlassSpection User Guide i GlassSpection User Guide GlassSpection User Guide v1.1a January2011 ii Support: Support for GlassSpection is available from Pyramid Imaging. Send any questions or test images you want us to evaluate

More information

EAN-Blending. PN: EAN-Blending 11/30/2017. SightLine Applications, Inc.

EAN-Blending. PN: EAN-Blending 11/30/2017. SightLine Applications, Inc. PN: EAN-Blending 11/30/2017 SightLine Applications, Inc. Contact: Web: sightlineapplications.com Sales: sales@sightlineapplications.com Support: support@sightlineapplications.com Phone: +1 (541) 716-5137

More information

Vision Sensors Inspector. The intelligent vision solution in an easy-to-use sensor package.

Vision Sensors Inspector. The intelligent vision solution in an easy-to-use sensor package. P R O D U C T I N F O R M AT I O N Vision Sensors Inspector The intelligent vision solution in an easy-to-use sensor package. Product overview Inspector I10 Inspector I20 Inspector I40 Inspector P30 Tough

More information

Technical Note How to Compensate Lateral Chromatic Aberration

Technical Note How to Compensate Lateral Chromatic Aberration Lateral Chromatic Aberration Compensation Function: In JAI color line scan cameras (3CCD/4CCD/3CMOS/4CMOS), sensors and prisms are precisely fabricated. On the other hand, the lens mounts of the cameras

More information

FEATURES Industry windows paperless solutions High speed portable document scanner is well-suited for a wide variety of Window industry

FEATURES Industry windows paperless solutions High speed portable document scanner is well-suited for a wide variety of Window industry BD-S-520 High-Speed Portable HD Document Scanner FEATURES Industry windows paperless solutions High speed portable document scanner is well-suited for a wide variety of Window industry Fast scan: One second

More information

Suitable firmware can be found on Anritsu's web site under the instrument library listings.

Suitable firmware can be found on Anritsu's web site under the instrument library listings. General Caution Please use a USB Memory Stick for firmware updates. Suitable firmware can be found on Anritsu's web site under the instrument library listings. If your existing firmware is older than v1.19,

More information

Digital Director Troubleshooting

Digital Director Troubleshooting Digital Director Troubleshooting Please find below the most common FAQs to assist in the understanding and use of the product. For details related to each specific camera model, refer to the Compatibility

More information

SCS1 SERIES. Smart Camera Sensor INSTRUCTION MANUAL

SCS1 SERIES. Smart Camera Sensor INSTRUCTION MANUAL SCS1 SERIES Smart Camera Sensor INSTRUCTION MANUAL We DECLARATION OF CONFORMITY DATASENSOR S.p.A. Via Lavino, 265 40050 Monte San Pietro Bologna - Italy declare under our sole responsibility that the product(s)

More information

i800 Series Scanners Image Processing Guide User s Guide A-61510

i800 Series Scanners Image Processing Guide User s Guide A-61510 i800 Series Scanners Image Processing Guide User s Guide A-61510 ISIS is a registered trademark of Pixel Translations, a division of Input Software, Inc. Windows and Windows NT are either registered trademarks

More information

Stitching MetroPro Application

Stitching MetroPro Application OMP-0375F Stitching MetroPro Application Stitch.app This booklet is a quick reference; it assumes that you are familiar with MetroPro and the instrument. Information on MetroPro is provided in Getting

More information

DS-620 DS-720D. Version C USA

DS-620 DS-720D. Version C USA User s Guide DS-620 / DS-720D DS-620 DS-720D Version C USA Using the documentation Thank you for buying a Brother machine! Reading the documentation will help you make the most of your machine. Symbols

More information

VISOR Solar User Manual

VISOR Solar User Manual Content 1 Purpose of this user manual... 5 2 Applications covered by VISOR Solar sensors... 6 2.1 Key features... 6 2.2 User benefits... 7 2.3 Interfaces... 8 3 Component selection... 8 3.1 Product lines...

More information

ISONIC PA AUT Spiral Scan Inspection of Tubular Parts Operating Manual and Inspection Procedure Rev 1.00 Sonotron NDT

ISONIC PA AUT Spiral Scan Inspection of Tubular Parts Operating Manual and Inspection Procedure Rev 1.00 Sonotron NDT ISONIC PA AUT Spiral Scan Inspection of Tubular Parts Operating Manual and Inspection Procedure Rev 1.00 Sonotron NDT General ISONIC PA AUT Spiral Scan Inspection Application was designed on the platform

More information

VISION SENSOR CS 50 THE WORLD S SMALLEST VISION SENSOR

VISION SENSOR CS 50 THE WORLD S SMALLEST VISION SENSOR VISION SENSOR THE WORLD S SMALLEST VISION SENSOR AS EASY TO USE AS A SENSOR. THE FEATURES. PERFECT FOR SHORT WORKING DISTANCES. Vision Sensor the world s smallest Vision Sensor offers powerful performance

More information

DOCUMENT SCANNER INSTRUCTIONS. Space. Backup. Count Only. New File. Scanner. Feeding Option Manual Auto Semi-Auto

DOCUMENT SCANNER INSTRUCTIONS. Space. Backup. Count Only. New File. Scanner. Feeding Option Manual Auto Semi-Auto E FILM F Scanner A Space Count Only New File Feeding Option Manual Auto Semi-Auto Backup DOCUMENT SCANNER INSTRUCTIONS NOTICE q Copyright 2001 by CANON ELECTRONICS INC. All rights reserved. No part of

More information

ROTATING SYSTEM T-12, T-20, T-50, T- 150 USER MANUAL

ROTATING SYSTEM T-12, T-20, T-50, T- 150 USER MANUAL ROTATING SYSTEM T-12, T-20, T-50, T- 150 USER MANUAL v. 1.11 released 12.02.2016 Table of contents Introduction to the Rotating System device 3 Device components 4 Technical characteristics 4 Compatibility

More information

The Practical use of LED Light Controllers within Machine Vision systems

The Practical use of LED Light Controllers within Machine Vision systems LED Light Controllers Technology overview The Practical use of LED Light Controllers within Machine Vision systems The successful, cost-effective application of a Machine Vision system is often dependent

More information

For customers in Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

For customers in Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. User manual For customers in North and South America For customers in USA This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not

More information

Picture Style Editor Ver Instruction Manual

Picture Style Editor Ver Instruction Manual ENGLISH Picture Style File Creating Software Picture Style Editor Ver. 1.18 Instruction Manual Content of this Instruction Manual PSE stands for Picture Style Editor. In this manual, the windows used in

More information

Exercise 3-3. Multiple-Source Jamming Techniques EXERCISE OBJECTIVE

Exercise 3-3. Multiple-Source Jamming Techniques EXERCISE OBJECTIVE Exercise 3-3 Multiple-Source Jamming Techniques EXERCISE OBJECTIVE To introduce multiple-source jamming techniques. To differentiate between incoherent multiple-source jamming (cooperative jamming), and

More information

User s Guide DS-620 DS-720D. Version A

User s Guide DS-620 DS-720D. Version A User s Guide DS-620 DS-720D Version A UK Using the documentation Thank you for buying a Brother machine! Reading the documentation will help you make the most of your machine. Symbols and conventions used

More information

Scanner Utility for Microsoft Windows Version 9.6. User's Guide

Scanner Utility for Microsoft Windows Version 9.6. User's Guide P3PC-E892-03EN Scanner Utility for Microsoft Windows Version 9.6 User's Guide For Use with Microsoft Windows 98, Windows Me, Windows 2000 and Windows XP Introduction Thank you for purchasing the "Scanner

More information

Harmony Remote Repair

Harmony Remote Repair Harmony Remote Repair harmonyremoterepair.com How to install your new Harmony One Front Cover/Touch Screen Important! Before you begin working on your Harmony One, you must discharge any static electricity

More information

Instructions for Tecnai a brief start up manual

Instructions for Tecnai a brief start up manual Instructions for Tecnai a brief start up manual Version 3.0, 8.12.2015 Manual of Tecnai 12 transmission electron microscope located at Aalto University's Nanomicroscopy Center. More information of Nanomicroscopy

More information

OTHER RECORDING FUNCTIONS

OTHER RECORDING FUNCTIONS OTHER RECORDING FUNCTIONS This chapter describes the other powerful features and functions that are available for recording. Exposure Compensation (EV Shift) Exposure compensation lets you change the exposure

More information

Internet of Things Student STEM Project Jackson High School. Lesson 2: Arduino and LED

Internet of Things Student STEM Project Jackson High School. Lesson 2: Arduino and LED Internet of Things Student STEM Project Jackson High School Lesson 2: Arduino and LED Lesson 2: Arduino and LED Time to complete Lesson 60-minute class period Learning objectives Students learn about Arduino

More information

Blue Point Engineering

Blue Point Engineering Blue Point Engineering Instruction I www.bpesolutions.com Pointing the Way to Solutions! Animatronic Wizard - 3 Board (BPE No. WAC-0030) Version 3.0 2009 Controller Page 1 The Wizard 3 Board will record

More information

An Activity in Computed Tomography

An Activity in Computed Tomography Pre-lab Discussion An Activity in Computed Tomography X-rays X-rays are high energy electromagnetic radiation with wavelengths smaller than those in the visible spectrum (0.01-10nm and 4000-800nm respectively).

More information

Step- by- Step Assembly Instructions (with photos)

Step- by- Step Assembly Instructions (with photos) Step- by- Step Assembly Instructions (with photos) Page Unpack the Photo Booth... 2 Secure the Power Cord... 3 Install the Camera Topper... 4 Load Paper into the Printers... 8 Load the Ink Film and Ink

More information

Picture Style Editor Ver Instruction Manual

Picture Style Editor Ver Instruction Manual ENGLISH Picture Style File Creating Software Picture Style Editor Ver. 1.15 Instruction Manual Content of this Instruction Manual PSE stands for Picture Style Editor. indicates the selection procedure

More information

Band-Master ATS Nano Pneumatic Banding Tool Operating Instructions

Band-Master ATS Nano Pneumatic Banding Tool Operating Instructions Band-Master ATS 601-118 Nano Pneumatic Banding Tool CONTENTS 601-118 Overview... 3 Safety.... 5 Initial Tool Set-up... 5 Regulator assembly mounting... 5 Attach tool head to regulator.... 6 Operating instructions...

More information

INSPECTION SENSORS SVS2 SERIES VISION SENSORS HIGHLIGHTS APPLICATIONS

INSPECTION SENSORS SVS2 SERIES VISION SENSORS HIGHLIGHTS APPLICATIONS INSPECTION VISION SENSORS SVS2 SERIES The SVS2 vision sensor series presents all the characteristics able to solve artifi cial machine vision applications in a fl exible and intuitive way. SVS2 is a completely

More information

MY ASTROPHOTOGRAPHY WORKFLOW Scott J. Davis June 21, 2012

MY ASTROPHOTOGRAPHY WORKFLOW Scott J. Davis June 21, 2012 Table of Contents Image Acquisition Types 2 Image Acquisition Exposure 3 Image Acquisition Some Extra Notes 4 Stacking Setup 5 Stacking 7 Preparing for Post Processing 8 Preparing your Photoshop File 9

More information

CAPTURING IMAGES ON THE HIGH-MAGNIFICATION MICROSCOPE

CAPTURING IMAGES ON THE HIGH-MAGNIFICATION MICROSCOPE University of Virginia ITC Academic Computing Health Sciences CAPTURING IMAGES ON THE HIGH-MAGNIFICATION MICROSCOPE Introduction The Olympus BH-2 microscope in ACHS s microscope lab has objectives from

More information

Bioloid Premium Kit Robot Arm Assembly Manual v1.0. Bioloid Premium Kit Robot Arm Assembly Manual

Bioloid Premium Kit Robot Arm Assembly Manual v1.0. Bioloid Premium Kit Robot Arm Assembly Manual Bioloid Premium Kit Robot Arm Assembly Manual v.0 Bioloid Premium Kit Robot Arm Assembly Manual Attention! Before proceeding with assembly, you must ensure each actuator s horn is properly aligned. To

More information

Exercise 2-2. Four-Wire Transmitter (Optional) EXERCISE OBJECTIVE DISCUSSION OUTLINE. Ultrasonic level transmitter DISCUSSION

Exercise 2-2. Four-Wire Transmitter (Optional) EXERCISE OBJECTIVE DISCUSSION OUTLINE. Ultrasonic level transmitter DISCUSSION Exercise 2-2 Four-Wire Transmitter (Optional) EXERCISE OBJECTIVE Become familiar with HART point-to-point connection of a four-wire transmitter. DISCUSSION OUTLINE The Discussion of this exercise covers

More information

CircumSpect TM 360 Degree Label Verification and Inspection Technology

CircumSpect TM 360 Degree Label Verification and Inspection Technology CircumSpect TM 360 Degree Label Verification and Inspection Technology Written by: 7 Old Towne Way Sturbridge, MA 01518 Contact: Joe Gugliotti Cell: 978-551-4160 Fax: 508-347-1355 jgugliotti@machinevc.com

More information

Laser Damage Threshold System For Final Optics Testing

Laser Damage Threshold System For Final Optics Testing University of California, San Diego UCSD-LPLM-06-01 Laser Damage Threshold System For Final Optics Testing Lane Carlson June 5, 2006 Laser Plasma and Laser Matter Interactions Center for Energy Research

More information

The Fastest, Easiest, Most Accurate Way To Compare Parts To Their CAD Data

The Fastest, Easiest, Most Accurate Way To Compare Parts To Their CAD Data 210 Brunswick Pointe-Claire (Quebec) Canada H9R 1A6 Web: www.visionxinc.com Email: info@visionxinc.com tel: (514) 694-9290 fax: (514) 694-9488 VISIONx INC. The Fastest, Easiest, Most Accurate Way To Compare

More information

WiseContact. scan, edit, analyze

WiseContact. scan, edit, analyze WiseContact scan, edit, analyze W isecontact package combines the power of WiseImage software and special plug-in to solve the toughest pressure measurement problems. It can process monochrome, grayscale

More information

Downloading a ROBOTC Sample Program

Downloading a ROBOTC Sample Program Downloading a ROBOTC Sample Program This document is a guide for downloading and running programs on the VEX Cortex using ROBOTC for Cortex 2.3 BETA. It is broken into four sections: Prerequisites, Downloading

More information