TECHNICAL INFORMATION P10/0513 vitroflex LED EDGELIGHT features

Transcription

1 TECHNICAL INFORMATION P10/0513 vitroflex LED EDGELIGHT features Vitroflex LED EDGELIGHT is the special compact acrylic sheet for signage illuminated around the perimeter of the sheet by LEDs. LED EDGELIGHT panel with grid LED EDGELIGHT panel without grid PROPERTIES Product specially designed for perimeter lighting by LEDs. Lighter and 10 times more resistant to impact than glass. A single strip of LEDs placed on the side lights up to 800 mm away without loss of light. Mounting two counter posed strips of LEDs can be illuminated homogeneously to 1600 mm distance between them. It allows homogeneity lighting without shadows. Light box cover with diffuser inside Page 1 of 6

2 No se puede mostrar la imagen en este momento. It supports all types of printed coatings intended for retro-illuminated, such as textiles, adhesive sheeting, vinyl, laminates, digital printing, screen printing, finishing with embossing, etc. It allows compact light boxes of only 8 cm thickness. APPLICATIONS Its use is recommended in all types of interior displays, primarily those requiring very little depth. It can also be used in lamps for interior lighting. - Mounting example: a. Rear reflector panel b. Vitroflex EDGELIGHT c. Diffuser sheet that can be printed d. Perimeter frame which prevents the light output e. Strip of LEDs MAINTENANCE It is recommended to clean using a gentle soap solution (neutral ph) with warm water and a nonabrasive cloth. The use of aggressive detergents with non-neutral ph can reduce the service life. The use of glass washers with alcohol or other similar products may negatively affect the properties and reduce the service life. Page 2 of 6

3 If an adequate disinfection is required, it is advisable to refer to the table of chemical resistance of Vitroflex, test a piece with no value, and preferably use the manufacturer recommended products only. In case the surface has small scratches due to the daily use, they can be removed using a specific polish for car bodies that is used manually. If deep scratches appear or if it is necessary to polish large surfaces, it is advisable to use an orbital eccentric polishing machine. RANGE Size: 800 x 2000 mm to put a 2000 mm strip of LEDs on one side 1600 x 2000 mm to put a 2000 mm strip of LEDs on each side These formats can be cut to smaller sizes in both magnitudes. Other measures are possible on request. Thickness: - 6, 8 and 10 are the most common for providing very good uniformity of light. - Other thicknesses with minimum order can be produced (110 m2). - Apply the tolerances according to ISO 7823/1. Colours: - Different degrees of light transmission and diffusion are available. Check technical data sheet. - Other colours available under minimum order of 110 m2. QUALITY Compliance with the standard ISO 7823/1 applicable to sheets of methacrylate casting, with independent laboratory certificate. All pieces are inspected individually. Page 3 of 6

4 OTHER AVAILABLE INFORMATION Table of resistance to various chemical products. MSDS for handling "Safety Data Sheet". Installation manual. Methacrylate basic manual manipulation. Technical manual of LED lighting systems. Page 4 of 6

5 Vitroflex EDGELIGHT TECHNICAL FEATURES ISO Physical properties Relative density - Volumetric mass (A Method) 1,19 g/cm 3 ISO 1183 Water absorption (Method 1) 0,19 % ISO 62 Thickness tolerance in 5 mm sheet ± 0.9 mm ISO 7823 Thickness tolerance in 18 mm sheet ± 2.2 mm ISO 7823 Mechanical properties Tensile strength (Type 1 Test, B speed) 72 MPa ISO 527 Traction elasticity module (Type 1 Test, B speed) 3000 MPa ISO 527 Elongation at break (Type 1 Test, B speed) 4 % ISO 527 Impact strength. Charpy method 16 KJ/m 2 ISO 179/2D Rockwell hardness (M Scale) -- ISO 2039/2 Bending strength 116 MPa ISO 178 Thermal properties Coefficient of linear expansion 70, K -1 EN VICAT softening temperature 105 ºC ISO 306 Bending temperature under load (A Method, 1,8 MPa) -- ºC ISO 75 Dimension variation at elevated temperatures (shrinkage) 2,3 % Annex Optical properties MCEDGE5N MCEDGE10NN Thickness ( mm ) 3-10 mm 3-10 mm Light transmission ( % ) ISO % 80 % Finished surface With grid Without grid Material Cast methacrylate Non-drip 1 Typical values are not intended for the design. Page 5 of 6

6 Important: The information and statements included are believed to be reliable; however, they should not be interpreted as a guarantee or representation that Polimer Tecnic assumes the legal responsibility. Users must perform all verifications and tests as appropriate to determine the particular suitability of any information or product mentioned in this document. Polimer Tecnic cannot guarantee the competence of the material for any particular purpose. Nothing in this document may be interpreted as a permission, incentive or recommendation to operate any patented invention without a license. Page 6 of 6