BUREAU OF INDIAN STANDARDS. Draft Indian Standard TWO COMPONENTS HIGH BUILD EPOXY MICACIOUS IRON OXIDE (MIO) PIGMENTED INTERMEDIATE COAT SPECIFICATION

Size: px
Start display at page:

Download "BUREAU OF INDIAN STANDARDS. Draft Indian Standard TWO COMPONENTS HIGH BUILD EPOXY MICACIOUS IRON OXIDE (MIO) PIGMENTED INTERMEDIATE COAT SPECIFICATION"

Transcription

1 FOR BIS USE ONLY DOC:CHD 20 (1932)C December 2012 BUREAU OF INDIAN STANDARDS Draft Indian Standard TWO COMPONENTS HIGH BUILD EPOXY MICACIOUS IRON OXIDE (MIO) PIGMENTED INTERMEDIATE COAT SPECIFICATION (Not to be reproduced without the permission of BIS or used as STANDARD) Last date for receipt of comments is FORWARD (formal clauses will be added later) 1 SCOPE 1.1 This standard prescribes requirements and method of sampling and test for two component epoxy Micacious Iron oxide pigmented Intermediate coat. 1.2 This material is expected to have adhesion on inorganic zinc silicate coating and epoxy based primers, with high toughness and abrasion resistance. This material is used as an intermediate coat for the painting of steel equipments and steel structures of Thermal Power Plant where protections from salt water, chemicals, mineral oils, solvents and resistance to moisture, protection under marine/refinery conditions are required. 2. REFERENCES The standards listed in Annex A contain provisions which through reference in this text, constitute provisions of and necessary adjuncts to this standard. At the time of publication, the editions indicated were valid. All standards are subject to revision and parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated in Annex A. 3 TERMINOLOGY For the purpose of this standard the terms and definitions used in IS 1303 shall apply. 4. REQUIREMENTS: 4.1 Composition Paints complying with this standard shall comprise of epoxy resin as the principal binder. The manufacturer shall specify that the principal type of binder used in the paint has epoxy equivalent in the range of 350 to 600. A test certificate preferably from a reputed testing agency 1

2 shall be furnished by the manufacturer confirming Micacious iron oxide by X-Ray Diffraction method. The composition shall be such that it satisfies the requirements specified in this standard The paint shall consist essentially of two components viz. base and hardener or catalyst solution to be mixed in the appropriate ratio by volume as specified by paint supplier to satisfy all the requirements of this standard. 4.2 Keeping Properties The material shall conform to all the requirements as mentioned in Table 1 for a minimum period of one year from the date of manufacture when stored in original sealed containers under normal atmospheric condition. 4.3 The material shall conform to the requirements given in Table TESTS 5.1 Unless specified otherwise, tests shall be conducted as prescribed in different parts of IS 101, preferably on the blasted panels. Reference to the relevant Sections of that standard are given in col 4 of Table The preparation of metal panels shall be according to IS 101 (Part 1/Sec 3) 5.3 Quality of Reagents Unless or otherwise specified, pure chemicals and distilled water (see IS 1070) Shall be employed. NOTE: Pure chemicals shall mean chemicals that do not contain impurities which affect the results of analysis. 5.4 Test certificate shall be in a format as agreed to between purchaser and supplier. 6. PACKING AND MARKING 6.1 Packing The material shall be packed in dual container. It shall ensure that the quality does not deteriorate during transit &storage and shall be as agreed to between Purchaser and supplier. 6.2 Marking Each container shall be marked with the following information: i) Indication of the source of manufacture, ii) Batch number or Lot number in code or otherwise; iii) Month and year of manufacture; iv) Date of expiry, v) Mass of the material. vi) Mixing Ratio BIS Certification Marking The product may also be marked with the Standard Mark on the container The use of the Standard Mark is governed by the provisions of Bureau of Indian Standards Act, 1986 and the Rules and Regulations made there under. The details of conditions 2

3 Table 1 Requirements of Epoxy MIO pigmented Intermediate coat, (Clauses 4.3 and 5.1) s.no Characteristic Requirement Method of Test, Ref to IS Annex 101 (1) (2) (3) (4) (5) A) WET PAINT i) Mass in kg / 10 ltrs, Min 15.5 Part 1/ Sec 7 - ii) Consistency To pass the test B iii) Flash Point Above 20 c Part 1/ Sec 6 - iv) Drying time, Max a) Surface dry b) Hard dry 4 h 16 h Part 3/ Sec 1 v) Percent volume, solids 55 Part 8/ Sec 6 - Min vi) Micacious Iron oxide (as Fe2O3) % By Mass on 50 Clause 6 of IS 6947 (Part II) pigment (min) vi) Pot life, Min 6 h C NOTE: Tests from SI.No. (i) to (vi) are for mixed paint. B) DRY COAT i) Dry film thickness per microns Part 3/ Sec 2 - coat, Min ii) Colour Brown Part 4/ Sec 2 - iii) Finish Egg shell/matt Part 3/ Sec 4 - v) Scratch hardness test To pass the test Clause 3 of Part 5/ Sec2 - (1 500g) vi) Flexibility and adhesion To pass the test Clause 2 of Part 5/ Sec2 - vii)** Resistance to humidity - under conditions of condensation at 500 h a) Resistance to to pass the test Clause 2 of Part 6/Sec 1 humidity for 500 h b) Resistance to salt spray for 500 h to pass the test Clause 3 of Part 6/Sec 1 ** These tests shall be conducted for a system consisting of one coat of Epoxy Zinc Phosphate Primer to IS or equivalent primer to be agreed upon between customer and supplier and one coat of intermediate paint. under which the Iicence for the use of the Standard Mark may be granted to manufacturers or producers may be obtained from the Bureau of Indian Standards. 7 SAMPLING 7.1 Representative samples of the material shall be drawn according to 6 of IS 101(Part1/Sec1). 3

4 A N N E X (Clause 2) A LIST OF REFERRED INDIAN STANDARDS IS No. Title IS 101 Methods of sampling and test for paints, varnishes and related products (Part 1/ Part 1 Test on liquid paints (general and physical), Sec 1) : 1986 Sec 1 Sampling (third revision) Sec 3) : 1986 Sec 3 Preparation of panels (third revision) Sec 5) : 1989 Sec 5 consistency (third revision) Sec 6) : 1987 Sec 6 Flash point (third revision) Sec 7) : 1987 Sec 7 (third revision) (Part 3/ Part 3 Test on paint film formation, Sec 1) : 1986 Sec 1 Drying time (third revision) Sec 2) : 1989 Sec 2 Film Thickness (third revision) Sec 4) : 1987 Sec 4 Finish (third revision) (Part 4/ Part 4 Optical tests on paint films Part 4 Optical tests on paint films Sec 2) : 1989 Sec 2 Colour (third revision) (Part 5/ Part 5 Mechanical tests on paint films Sec 1) : 1988 Sec 1 Hardness test (third revision) Sec 2) : 1988 Sec 2 Flexibility and adhesion tests (third revision) (Part 6/ Part 6 Durability test on paint films Sec 1) : 1988 Sec 1 Durability under conditions of condensation IS 1070 : 1992 Reagent grade Water (third revision) IS 1303 : 1983 Glossary of terms relating to paint (second revision) IS 6947 (Part II) Methods of estimation of composite pigments in Oil pastes, ready mixed paints and Enamels-Part II-Estimation of Zinc Chrome, Ferric Oxide and Aluminium. B-1 APPARATUS B-1.1 Palette Knife or Metal Rod B-1.2 Panels A N N E X B [Table 1, Sl No. ii)] CONSISTENCY B Unless specified otherwise, steel panels described under 2 of IS 101(Part 1/Sec 3) shall be prepared. B-2 PROCEDURE B-2.1 Insert a clean metal rod or palette knife into the original container and examine the nature of settling. 4

5 B-2.2 Observations - The material shall not cake hard inside the container and shall be in such a condition that stirring easily produces a smooth uniform paint suitable for coating on steel A N N E X C [Table 1, Sl No. vi)] C-1 GENERAL DETERMINATION OF POT LIFE C-1.1 The time taken to double the viscosity from the original value shall be considered as the pot life of the material. C-2 PROCEDURE C-2.1 Thoroughly mix component parts in the ratio specified by the paint manufacturer to give a sample of 200 ml by volume. C-2.2 Within 10 minutes of mixing (B-2.1) determine the viscosity as prescribed in IS 101 (Part 1/Sec 5). C-2.3 Allow the mixed sample of paint to stand in a suitable air-tight container and determine the Viscosity at the end of the specified time. 5

FOR READY MIXED PAINT, ALUMINIUM, BRUSHING, PRIMING, WATER RESISTANT, FOR WOODWORK

FOR READY MIXED PAINT, ALUMINIUM, BRUSHING, PRIMING, WATER RESISTANT, FOR WOODWORK FOR BIS USE ONLY DOC:CHD 20(1907)C August 2011 BUREAU OF INDIAN STANDARDS Draft Indian Standard SPECIFICATION FOR READY MIXED PAINT, ALUMINIUM, BRUSHING, PRIMING, WATER RESISTANT, FOR WOODWORK (First Revision

More information

(First Revision of IS 2339) (Not to be reproduced without the permission of BIS or used as STANDARD)

(First Revision of IS 2339) (Not to be reproduced without the permission of BIS or used as STANDARD) FOR BIS USE ONLY DOC:CHD 20(1877)C July 2011 BUREAU OF INDIAN STANDARD Draft Indian Standard SPECIFICATION FOR ALUMINIUM PAINTS FOR GENERAL PURPOSES Part 2 for industrial and commercial applications (First

More information

BUREAU OF INDIAN STANDARDS. Draft Indian Standard EPOXY NON-SKID PAINT(BASE AND HARDNER)

BUREAU OF INDIAN STANDARDS. Draft Indian Standard EPOXY NON-SKID PAINT(BASE AND HARDNER) FOR BIS USE ONLY DOC:CHD 20 (1933)C December 2012 BUREAU OF INDIAN STANDARDS Draft Indian Standard EPOXY NON-SKID PAINT(BASE AND HARDNER) (Not to be reproduced without the permission of BIS or used as

More information

WATER-BORNE SOL-GEL BASED BINDERS FOR THE FORMULATION OF AMBIENT CURING ZINC DUST PAINTS

WATER-BORNE SOL-GEL BASED BINDERS FOR THE FORMULATION OF AMBIENT CURING ZINC DUST PAINTS WATER-BORNE SOL-GEL BASED BINDERS FOR THE FORMULATION OF AMBIENT CURING ZINC DUST PAINTS Björn Borup, Philipp Albert, Helmut Mack Evonik Industries, Germany Introduction Regulatory pressure and increasing

More information

For questions, concerning corrosion protection, contact our Mr. Franke under Telephone No. +49-(0) , or Fax No.+49-(0) ).

For questions, concerning corrosion protection, contact our Mr. Franke under Telephone No. +49-(0) , or Fax No.+49-(0) ). SCHORCH Paint System (Author: Hinrichs / Dep. Q1) Contents 1: General 2: Warranty / paint systems to customers specifications 3: Contact person at SCHORCH 4: Attached index 5: Site conditions of SCHORCH

More information

HUE' TITLE: - FULL GLOSS POLYURETHANE FINISHING PAINT THE/1 t\-5. 8 gyer if 1 PAGE 1 OF SCOPE

HUE' TITLE: - FULL GLOSS POLYURETHANE FINISHING PAINT THE/1 t\-5. 8 gyer if 1 PAGE 1 OF SCOPE 47Y-f HUE' TITLE: - FULL GLOSS POLYURETHANE THE/1 t\-5 8 gyer if 1 PAGE 1 OF 8 1.0 SCOPE :11 -o O This specification governs the quality requirements of air / oven drying Polyurethane Finishing Paint (Two

More information

SPECIFICATION FOR PAPER STATIONERY ITEMS FOR SCHOOLS ( First Revision of IS 5195)

SPECIFICATION FOR PAPER STATIONERY ITEMS FOR SCHOOLS ( First Revision of IS 5195) FOR BIS USE ONLY DOC:CHD15 (1857)C April 2011 BUREAU OF INDIAN STANDARDS Draft Indian Standard SPECIFICATION FOR PAPER STATIONERY ITEMS FOR SCHOOLS ( First Revision of IS 5195) (Not to be reproduced without

More information

High-quality, water-dilutable satin gloss enamel on the basis of a modified alkyd technology.

High-quality, water-dilutable satin gloss enamel on the basis of a modified alkyd technology. Product Data Sheet High-quality, water-dilutable satin gloss enamel on the basis of a modified alkyd technology. ralstoncolour.com /picto Excellent outdoor resistance Excellent flow and optimal hiding

More information

MATERIAL AND EQUIPMENT STANDARD FOR ALKYD PAINT (ALUMINUM) LEAFING TOP COAT (FINISH) ORIGINAL EDITION AUG. 1993

MATERIAL AND EQUIPMENT STANDARD FOR ALKYD PAINT (ALUMINUM) LEAFING TOP COAT (FINISH) ORIGINAL EDITION AUG. 1993 MATERIAL AND EQUIPMENT STANDARD FOR ALKYD PAINT (ALUMINUM) LEAFING AS TOP COAT (FINISH) ORIGINAL EDITION AUG. 1993 This standard specification is reviewed and updated by the relevant technical committee

More information

Epoxy Coal Tar. Protects Steel and Concrete in Marine and Industrial Environments.

Epoxy Coal Tar. Protects Steel and Concrete in Marine and Industrial Environments. Epoxy Coal Tar Protects Steel and Concrete in Marine and Industrial Environments. General Epoxy Coal Tar is a protective coating designed to resist chemical attack and rigorous weather conditions by combining

More information

Suggested Specification for Preparing Hot-Dip Galvanized Steel Surfaces for Painting Revised February 2002

Suggested Specification for Preparing Hot-Dip Galvanized Steel Surfaces for Painting Revised February 2002 Suggested Specification for Preparing Hot-Dip Galvanized Steel Surfaces for Painting Revised February 2002 This suggested specification is provided as a guide to preparing a quality document calling for

More information

ISO INTERNATIONAL STANDARD

ISO INTERNATIONAL STANDARD INTERNATIONAL STANDARD ISO 12944-6 First edition 1998-05-15 Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 6: Laboratory performance test methods Peintures

More information

MATERIAL AND EQUIPMENT STANDARD FOR EPOXY POLYAMIDE PAINT AS INTERMEDIATE PAINT ORIGINAL EDITION MAY 1993

MATERIAL AND EQUIPMENT STANDARD FOR EPOXY POLYAMIDE PAINT AS INTERMEDIATE PAINT ORIGINAL EDITION MAY 1993 MATERIAL AND EQUIPMENT STANDARD FOR EPOXY POLYAMIDE PAINT AS INTERMEDIATE PAINT ORIGINAL EDITION MAY 1993 This standard specification is reviewed and updated by the relevant technical committee on Nov.

More information

DULUX UNIVERSAL UNDERCOAT

DULUX UNIVERSAL UNDERCOAT TECHNICAL DATA SHEET Version 1 2015 JUNE THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Intermediate coating for use under decorative topcoats, for interior and exterior use PRODUCT

More information

NOTE: This product can be used externally if UV Guard is added (BY REQUEST ONLY).

NOTE: This product can be used externally if UV Guard is added (BY REQUEST ONLY). Product Description PHOENIX PAINTS MAXICOAT 100 is a 2 Pack Water-Dispersed Top Coat which not only exhibits the physical and chemical strengths of epoxy, but also the safety and convenience of water as

More information

RAPTOR EPOXY PRIMER RAPTOR 4:1 ANTI-CORROSIVE EPOXY PRIMER DESCRIPTION

RAPTOR EPOXY PRIMER RAPTOR 4:1 ANTI-CORROSIVE EPOXY PRIMER DESCRIPTION Suitable as a primer or as a primer filler for industrial refinish applications, the primer also provides excellent anti-rust protection. Easy to apply Excellent anti-corrosion resistance Can be applied

More information

Paints and varnishes Corrosion protection of steel structures by protective paint systems. Part 5: Protective paint systems

Paints and varnishes Corrosion protection of steel structures by protective paint systems. Part 5: Protective paint systems Provläsningsexemplar / Preview INTERNATIONAL STANDARD ISO 12944-5 Third edition 2018-02 Paints and varnishes Corrosion protection of steel structures by protective paint systems Part 5: Protective paint

More information

PRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required

PRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required TECHNICAL DATA SHEET Version 1 2016 JULY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required

More information

ISO 3233 INTERNATIONAL STANDARD

ISO 3233 INTERNATIONAL STANDARD INTERNATIONAL STANDARD ISO 3233 Third edition 1998-08-15 Paints and varnishes Determination of percentage volume of non-volatile matter by measuring the density of a dried coating Peintures et vernis Détermination

More information

Data Sheet 5741 Englisch

Data Sheet 5741 Englisch Data Sheet 5741 Englisch 2K-PUR-Acryl Silk Gloss 2K-PUR-Acryl Seidenglanzlack 5741 two-component, high mechanical resistance, for exterior and interior use, with 2K-PUR-Acryl Hardener 5770 2K-PUR-Acryl

More information

CDC 13 (4228) P 3 Bituminous paint for cold application excluding use in contact with potable water Specification

CDC 13 (4228) P 3 Bituminous paint for cold application excluding use in contact with potable water Specification DRAFT TANZANIA STANDARD CDC 13 (4228) P 3 Bituminous paint for cold application excluding use in contact with potable water Specification TANZANIA BUREAU OF STANDARDS. 1 st edition TBS 2015 0. FOREWORD

More information

CORPORATE PURCHASING SPECIFICATIONS

CORPORATE PURCHASING SPECIFICATIONS CORPORATE PURCHASING AA56142 os PREFACE SHEET FULL GLOSS POLYURETHANE FINISHING PAINT INTERNAL ONLY REMOVE T S PREFACE SHEET BEFORE I UE TO SUPPLIERS Equivalent / Corn arable tandards: 1. INDIAN IS:13213-1991

More information

SPECIFICATION FOR WATERBORNE TRAFFIC LINE PAINT

SPECIFICATION FOR WATERBORNE TRAFFIC LINE PAINT Page 1 of 5 ATTACHMENT I Commonwealth of Pennsylvania Department of Transportation SPECIFICATION FOR WATERBORNE TRAFFIC LINE PAINT August 14, 2006 1. SCOPE 1.1 Scope. This specification covers fast-drying

More information

MATERIAL AND EQUIPMENT STANDARD FOR RED LEAD, IRON OXIDE, RAW LINSEED OIL AND ALKYD PRIMER ORIGINAL EDITION MAY 1993

MATERIAL AND EQUIPMENT STANDARD FOR RED LEAD, IRON OXIDE, RAW LINSEED OIL AND ALKYD PRIMER ORIGINAL EDITION MAY 1993 IPSMTP115 MATERIAL AND EQUIPMENT STANDARD FOR RED LEAD, IRON OXIDE, RAW LINSEED OIL AND ALKYD PRIMER ORIGINAL EDITION MAY 1993 This standard specification is reviewed and updated by the relevant technical

More information

BUREAU OF INDIAN STANDARDS. Draft Indian Standard. SPECIFICATION FOR ENAMEL, EXTERIOR, (a) UNDERCOATING, (b) FINISHING

BUREAU OF INDIAN STANDARDS. Draft Indian Standard. SPECIFICATION FOR ENAMEL, EXTERIOR, (a) UNDERCOATING, (b) FINISHING FOR BIS USE ONLY DOC:CHD 20 (1870)C June 2011 BUREAU OF INDIAN STANDARDS Draft Indian Standard SPECIFICATION FOR ENAMEL, EXTERIOR, (a) UNDERCOATING, (b) FINISHING Part 1 For Household and decorative purposes

More information

SELECTION AND PREPARATION OF SUBSTRATES

SELECTION AND PREPARATION OF SUBSTRATES 592 TECHNICAL DATASHEET 7-538 / 7-539 SELEMIX DIRECT GLOSS TOPCOATS PRODUCT DESCRIPTION Selemix Direct Gloss are polyurethane coatings based on PU 2K technology, which can be applied direct onto substrates

More information

DRAFT TANZANIA STANDARD. TBS/CDC-2(4970) P3- Carbolic Soap - Specification (Revision of TZS 221:1984)

DRAFT TANZANIA STANDARD. TBS/CDC-2(4970) P3- Carbolic Soap - Specification (Revision of TZS 221:1984) DRAFT TANZANIA STANDARD TBS/CDC-2(4970) P3- Carbolic Soap - Specification (Revision of TZS 221:1984) TANZANIA BUREAU OF STANDARDS Foreword This Draft Tanzania Standard is being developed by the Soap and

More information

In addition to point 1. containers face the following corrosive conditions like :

In addition to point 1. containers face the following corrosive conditions like : THE DEVELOPMENT OF CONTAINER COATINGS There are now in excess of 4 million TEU in the world they predominate the world trades, and are frequently seen on the oceans, rivers, roads, rails and even airplanes

More information

MATERIAL AND EQUIPMENT STANDARD FOR ZINC SILICATE (INORGANIC ZINC-RICH) PAINT PRIMER, INTERMEDIATE AND TOP COAT ORIGINAL EDITION MAY 1993

MATERIAL AND EQUIPMENT STANDARD FOR ZINC SILICATE (INORGANIC ZINC-RICH) PAINT PRIMER, INTERMEDIATE AND TOP COAT ORIGINAL EDITION MAY 1993 MATERIAL AND EQUIPMENT STANDARD FOR ZINC SILICATE (INORGANIC ZINC-RICH) PAINT AS PRIMER, INTERMEDIATE AND TOP COAT ORIGINAL EDITION MAY 1993 This standard specification is reviewed and updated by the relevant

More information

P A I N T I N G S Y S T E M. This specification has been divided into 05 chapters designated as under :

P A I N T I N G S Y S T E M. This specification has been divided into 05 chapters designated as under : RDSO SPECIFICATION NO. M&C/PCN/100/2006 SPECIFICATION FOR POLYURETHANE PAINTING SYSTEM (TWO PACK) FOR THE EXTERIOR PAINTING OF RAILWAY COACHES DIESEL AND ELECTRIC LOCOMOTIVES AND OTHER INDUSRIAL APPLICATIONS

More information

TECHNICAL SPECIFICATION FOR G. I. WIRE (4MM)

TECHNICAL SPECIFICATION FOR G. I. WIRE (4MM) 1. SCOPE: TECHNICAL SPECIFICATION FOR G. I. WIRE (4MM) This Specification provides for manufacture, testing before dispatch at manufacturer's work and supply and delivery of 4mm solid heavily coated Galvanized

More information

Physical constants Finish: ASTM D Flash point: Rangan Far, s Adding thinner to a paint may change the flash point of the diluted material.

Physical constants Finish: ASTM D Flash point: Rangan Far, s Adding thinner to a paint may change the flash point of the diluted material. Finish: The appearance of the paint film after drying under optimum conditions,- given as high gloss (>90), gloss (60-90), semi-gloss (30-60), semi-flat (15-30), or flat (

More information

EDICT ± OF GOVERNMENT

EDICT ± OF GOVERNMENT EDICT ± OF GOVERNMENT Inordertopromotepubliceducationandpublicsafety,equal justiceforal,abeterinformedcitizenry,theruleoflaw,world tradeandworldpeace,thislegaldocumentisherebymade availableonanoncommercialbasis,asitistherightofal

More information

General description: Two-component high-build, high solids surface tolerant universal epoxy coating. For painting on steel and galvanized steel substrates. Certified for systems category C5I High ISO 12944.

More information

COLOUR SHADES - OVERVIEW

COLOUR SHADES - OVERVIEW Product Data Sheet Pad Printing Ink TP 218/GL Solvent Based Pad Printing Ink Range, 2-Component APPLICATION Pad printing inks for printing on glass, ceramics, duroplastics, metals as well as chromium and

More information

South African Qualification and Certification Committee (Corrosion Protection) SYLLABUS MODULE PS PAINTING SUPERVISORS COURSE

South African Qualification and Certification Committee (Corrosion Protection) SYLLABUS MODULE PS PAINTING SUPERVISORS COURSE 1/8 South African Qualification and Certification Committee (Corrosion Protection) APPENDIX SYLLABUS MODULE PAINTING COURSE DURATION: The planned duration is a minimum 5 day course and the theory and practical

More information

Unit PO0205K Knowledge of Applying Fillers and Foundation Materials

Unit PO0205K Knowledge of Applying Fillers and Foundation Materials Assessment Requirements Unit PO0205K Knowledge of Applying Fillers and Foundation Materials Content: The types of substrates likely to be found in vehicle refinishing a. List types of substrate to include:

More information

COMBINED METERING TRANSFORMERS (OUT DOOR TYPE) FOR 11kV & 33kV SYSTEMS

COMBINED METERING TRANSFORMERS (OUT DOOR TYPE) FOR 11kV & 33kV SYSTEMS 006: 2008 CEB SPECIFICATION COMBINED METERING TRANSFORMERS (OUT DOOR TYPE) FOR 11kV & 33kV SYSTEMS CEYLON ELECTRICITY BOARD SRI LANKA Specification for COMBINED METERING TRANSFORMERS (OUTDOOR TYPE) FOR

More information

UNIT TITLE: KNOWLEDGE OF APPLYING FILLERS AND FOUNDATION MATERIALS

UNIT TITLE: KNOWLEDGE OF APPLYING FILLERS AND FOUNDATION MATERIALS UNIT REF: PO0205K UNIT TITLE: KNOWLEDGE OF APPLYING FILLERS AND FOUNDATION MATERIALS Level: 2 Route: Knowledge Credit Value: 6 GLH: 45 Mapping: This unit is mapped to the IMI NOS PO2 and PO5 Rationale:

More information

CKS 440* *This standard references other standards Edition CKS. Coffins and caskets CKS 440 ICS ISBN

CKS 440* *This standard references other standards Edition CKS. Coffins and caskets CKS 440 ICS ISBN ICS 55.160 ISBN 0-626-09381-3 CKS 440* *This standard references other standards Edition 2 1993 CKS Coffins and caskets Published by THE SOUTH AFRICAN BUREAU OF STANDARDS Gr 6 Notice This specification

More information

SECTION-I (G.I.PLAIN WIRE) TECHNICAL SPECIFICATION FOR G. I. WIRE

SECTION-I (G.I.PLAIN WIRE) TECHNICAL SPECIFICATION FOR G. I. WIRE SECTION-I (G.I.PLAIN WIRE) TECHNICAL SPECIFICATION FOR G. I. WIRE 1. SCOPE :- This Specification provides for manufacture, testing before dispatch at manufacturer's work and supply and delivery of 3.15mm

More information

2K weather resistance clear coat A850

2K weather resistance clear coat A850 Clear coat Donglai Coating Technology (Shanghai) Co., Ltd. 2K weather resistance clear coat A850 Description High-build, two-component clear coat designed for universal application and optimal appearance

More information

GURANTEED TECHNICAL PARTICULARS OF BACK CLAMP FOR LT CROSS ARM

GURANTEED TECHNICAL PARTICULARS OF BACK CLAMP FOR LT CROSS ARM Technical Specification of Back Clamp for LT Cross Arm (MS) Back clamp for LT Cross Arm made out of 50 x 6mm MS Flat suitable for 8m X 300 Kg PSC poles. After fabrication the cross arm shall be painted

More information

MATERIAL AND EQUIPMENT STANDARD FOR ALKYD PAINT (ALUMINUM) NON - LEAFING INTERMEDIATE ORIGINAL EDITION AUG. 1993

MATERIAL AND EQUIPMENT STANDARD FOR ALKYD PAINT (ALUMINUM) NON - LEAFING INTERMEDIATE ORIGINAL EDITION AUG. 1993 MATERIAL AND EQUIPMENT STANDARD FOR ALKYD PAINT (ALUMINUM) NON - LEAFING AS INTERMEDIATE ORIGINAL EDITION AUG. 1993 This standard specification is reviewed and updated by the relevant technical committee

More information

Aerodur 3001 Base Coat Special Effects

Aerodur 3001 Base Coat Special Effects Technical Data Sheet Product Group Polyurethane Topcoats Characteristics Product Information Aerodur 3001 topcoat is part of the high solid 3 components polyurethane Aerodur 3001 Solid Colors Aerodur 3001

More information

Jiangsu DAQO. Enclosed Busbar Systems. Procedure Specification. Painting Procedure Specification

Jiangsu DAQO. Enclosed Busbar Systems. Procedure Specification. Painting Procedure Specification Company Jiangsu DAQO Edition No.1 Name Enclosed Busbar Systems Co., Ltd Files Procedure Specification Serial DQFM-ZD-08-004 Classes Painting Procedure Specification 1 Surface Treatment before Painting

More information

INDUSTRIAL PAINTS INDUSTRIAL TOP COAT 6 GENERAL 6 ACRYLIC LACQUERS 8 ALKYD LACQUERS 10

INDUSTRIAL PAINTS INDUSTRIAL TOP COAT 6 GENERAL 6 ACRYLIC LACQUERS 8 ALKYD LACQUERS 10 COLORS www.soppec.com EVENT COLORS PRO TECH INDUSTRIAL PAINTS In all industrial or agricultural activities it is important to be able to carry out rapid repairs to damaged paintwork, (notably to machinery

More information

Technical Data Sheet Primers/Surfacers LV 350 Primer EP FOR PROFESSIONAL USE ONLY

Technical Data Sheet Primers/Surfacers LV 350 Primer EP FOR PROFESSIONAL USE ONLY 4 3505-002 1 3505-105 0.5 3505-204 Description: High solid two-pack epoxy primer-surfacer providing excellent appearance and corrosion protection. The target use for this product is refinishing and refurbish

More information

MATERIAL AND EQUIPMENT STANDARD FOR ZINC OXIDE, IRON OXIDE AND ALKYD INTERMEDIATE PAINT ORIGINAL EDITION MAY 1993

MATERIAL AND EQUIPMENT STANDARD FOR ZINC OXIDE, IRON OXIDE AND ALKYD INTERMEDIATE PAINT ORIGINAL EDITION MAY 1993 MATERIAL AND EQUIPMENT STANDARD FOR ZINC OXIDE, IRON OXIDE AND ALKYD INTERMEDIATE PAINT ORIGINAL EDITION MAY 1993 This standard specification is reviewed and updated by the relevant technical committee

More information

BUREAU OF INDIAN STANDARDS. Draft Indian Standard HOT APPLIED THERMOPLASTIC ROAD MARKING MATERIAL

BUREAU OF INDIAN STANDARDS. Draft Indian Standard HOT APPLIED THERMOPLASTIC ROAD MARKING MATERIAL FOR BIS USE ONLY DOC:CHD 20 (1937)C December 2012 BUREAU OF INDIAN STANDARDS Draft Indian Standard HOT APPLIED THERMOPLASTIC ROAD MARKING MATERIAL (Not to be reproduced without the permission of BIS or

More information

NEW COATINGS FOR THE FUNCTIONALIZATION OF ENAMELLED SURFACES

NEW COATINGS FOR THE FUNCTIONALIZATION OF ENAMELLED SURFACES NEW COATINGS FOR THE FUNCTIONALIZATION OF ENAMELLED SURFACES Giovanni Baldi Ce.Ri.Col. e-mail: baldig@colorobbia.it Andrea Cioni Ce.Ri.Col. e-mail: cionia@colorobbia.it Valentina Dami Ce.Ri.Col. e-mail:

More information

PRODUCT GUIDE FIRST FOR LASTING IMPRESSIONS

PRODUCT GUIDE FIRST FOR LASTING IMPRESSIONS PRODUCT GUIDE FIRST FOR LASTING IMPRESSIONS ULTRIMAX 1 ULTRIMAX 1 ULTRIMAX 1 THE NUMBER 1 FOR SAVING YOU TIME AND EFFORT ULTRIMAX 1 COMPLIANT PRIMER, GLOSS AND VALUE IN ONE Ultrimax 1 is a high build acrylicbased

More information

CG 303 Quality assurance scheme for paints and similar protective coatings

CG 303 Quality assurance scheme for paints and similar protective coatings Design Manual for Roads and Bridges Highway Structures & Bridges General information CG 303 Quality assurance scheme for paints and similar protective coatings (formerly BD 35/14) Revision 0 Summary This

More information

DRAFT UGANDA STANDARD

DRAFT UGANDA STANDARD DRAFT UGANDA STANDARD DUS 193-1 First Edition 2018-09-dd Steel wires and wire products for fencing Part 1: Barbed wires Specification Reference number UNBS 2018 Compliance with this standard does not,

More information

ISO INTERNATIONAL STANDARD. Fasteners Non-electrolytically applied zinc flake coatings

ISO INTERNATIONAL STANDARD. Fasteners Non-electrolytically applied zinc flake coatings INTERNATIONAL STANDARD ISO 63 First edition 2000-07-1 Fasteners Non-electrolytically applied zinc flake coatings Éléments de fixation Revêtements non électrolytiques de lamelles de zinc Reference number

More information

This document is a preview generated by EVS

This document is a preview generated by EVS INTERNATIONAL STANDARD ISO 8502-4 Second edition 2017-01 Preparation of steel substrates before application of paints and related products Tests for the assessment of surface cleanliness Part 4: Guidance

More information

MATERIAL AND EQUIPMENT STANDARD FOR COAL TAR MASTIC (COLD APPLIED) ORIGINAL EDITION AUG. 1993

MATERIAL AND EQUIPMENT STANDARD FOR COAL TAR MASTIC (COLD APPLIED) ORIGINAL EDITION AUG. 1993 MATERIAL AND EQUIPMENT STANDARD FOR COAL TAR MASTIC (COLD APPLIED) ORIGINAL EDITION AUG. 1993 This standard specification is reviewed and updated by the relevant technical committee on May 1999. The approved

More information

Fasteners Non-electrolytically applied zinc flake coatings

Fasteners Non-electrolytically applied zinc flake coatings INTERNATIONAL STANDARD ISO 10683 Second edition 2014-05-15 Fasteners Non-electrolytically applied zinc flake coatings Fixations Revêtements non électrolytiques de zinc lamellaire Reference number ISO 2014

More information

SPECIFICATION FOR PAINTING ON GALVANIZED SURFACES BY WET or ELECTROSTATIC POWDER PAINTING

SPECIFICATION FOR PAINTING ON GALVANIZED SURFACES BY WET or ELECTROSTATIC POWDER PAINTING CHIEF CHEMIST DEPT. PAGE No. 1 of 7 SPECIFICATION FOR PAINTING ON GALVANIZED SURFACES BY WET or ELECTROSTATIC POWDER PAINTING 1. SCOPE This specification covers the requirements for painting of steel surfaces

More information

MATERIAL AND EQUIPMENT STANDARD FOR VINYL PAINT (ALUMINUM) AS INTERMEDIATE AND TOP COAT (FINISH) ORIGINAL EDITION MAY 1993

MATERIAL AND EQUIPMENT STANDARD FOR VINYL PAINT (ALUMINUM) AS INTERMEDIATE AND TOP COAT (FINISH) ORIGINAL EDITION MAY 1993 MATERIAL AND EQUIPMENT STANDARD FOR VINYL PAINT (ALUMINUM) AS INTERMEDIATE AND TOP COAT (FINISH) ORIGINAL EDITION MAY 1993 This standard specification is reviewed and updated by the relevant technical

More information

012: 2015 CEB SPECIFICATION GALVANIZED STEEL WIRE (EXCEPT SHIELDING WIRE FOR TOWER LINE APPLICATION)

012: 2015 CEB SPECIFICATION GALVANIZED STEEL WIRE (EXCEPT SHIELDING WIRE FOR TOWER LINE APPLICATION) 012: 2015 CEB SPECIFICATION GALVANIZED STEEL WIRE (EXCEPT SHIELDING WIRE FOR TOWER LINE APPLICATION) CEYLON ELECTRICITY BOARD SRI LANKA Telephone: +94 11 232 8051 Fax: +94 11 232 5387 CONTENTS Page 1.0

More information

Contents. NIIR Project Consultancy Services (NPCS) 1/6

Contents. NIIR Project Consultancy Services (NPCS) 1/6 The Complete Book on Resins (Alkyd, Amino, Phenolic, Polyurethane, Epoxy, Silicone, Acrylic), Paints, Varnishes, Pigments & Additives (Surface Coating Products with Formulae)(3rd Revised Edition) Author:

More information

These Application Instructions cover surface preparation, application equipment and application details for HEMPADUR MASTIC 45880/45881.

These Application Instructions cover surface preparation, application equipment and application details for HEMPADUR MASTIC 45880/45881. For product description refer to product data sheet HEMPADUR MASTIC 45880/ HEMPADUR MASTIC 45880/ High temperatures: 45881: BASE 45889 with CURING AGENT 95881 Low to medium temperatures: 45880: BASE 45889

More information

IS INTERNATIONAL STANDARD. Steel tubes - Continuous character marking and colour coding for material identification. First edition

IS INTERNATIONAL STANDARD. Steel tubes - Continuous character marking and colour coding for material identification. First edition INTERNATIONAL STANDARD IS0 9095 First edition 1990-04-01 Steel tubes - Continuous character marking and colour coding for material identification Tubes et &ments tubulaires en acier - Marquage codifikes

More information

10P20-44MNF High Solids Epoxy Primer

10P20-44MNF High Solids Epoxy Primer Technical Data Sheet Product Group High solids epoxy primer Characteristics Product Information A high solids urethane compatible, Skydrol resistant primer for application to aircraft exterior surfaces.

More information

36kV VOLTAGE TRANSFORMERS (OUTDOOR TYPE)

36kV VOLTAGE TRANSFORMERS (OUTDOOR TYPE) CEB STANDARD 022 : 1994 Specification for 36kV VOLTAGE TRANSFORMERS (OUTDOOR TYPE) CEYLON ELECTRICITY BOARD SRI LANKA Specification for 36kV VOLTAGE TRANSFORMERS (OUTDOOR TYPE) CEB Standard 022 : 1994

More information

SPECIFICATION FOR AC-DC POWER SUPPLY FOR DEFENCE APPLICATION

SPECIFICATION FOR AC-DC POWER SUPPLY FOR DEFENCE APPLICATION SPECIFICATION FOR AC-DC POWER SUPPLY FOR DEFENCE APPLICATION Project : DEFENCE PROJECT Document number : PS 407195 Revision : 00 Date : 12/08/2016 Classification : Controlled Copy Name: Designation Signature:

More information

ISO INTERNATIONAL STANDARD. Paints and varnishes Determination of film hardness by pencil test

ISO INTERNATIONAL STANDARD. Paints and varnishes Determination of film hardness by pencil test INTERNATIONAL STANDARD ISO 15184 First edition 1998-11-01 Paints and varnishes Determination of film hardness by pencil test Peintures et vernis Détermination de la dureté du feuil par l essai de dureté

More information

SECTION 025 INDUSTRIAL PAINTING

SECTION 025 INDUSTRIAL PAINTING SECTION 025 INDUSTRIL PINTING Industrial painting, including all necessary preparation and application, except as modified in this Section, shall conform to the recommendations of the manufacturer of the

More information

EAST AFRICAN STANDARD

EAST AFRICAN STANDARD ICS 77.140 EAST AFRICAN STANDARD Pre-painted metal coated steel sheets and coils Specification EAST AFRICAN COMMUNITY EAC 2006 First Edition 2006 Foreword Development of the East African Standards has

More information

PROCESS CHECK REPORT

PROCESS CHECK REPORT Company: Process Title Process Check Report Ref. No: Raytheon Process Auditor(s): Date Of Process Audit: The Application Of Cold Curing Epoxide Finish Summary: Conclusion: Distribution: Auditor: Approved

More information

SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS

SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS UDC 621.882.211 [669.14.018.291] IS : 3757-1985 (Reaffirmed 2003) Edition 3.2 (1989-07) Indian Standard SPECIFICATION FOR HIGH STRENGTH STRUCTURAL BOLTS ( Second Revision ) (Incorporating Amendment Nos.

More information

Application Guide for Jotun Primax Diamond Powder Coatings

Application Guide for Jotun Primax Diamond Powder Coatings for Jotun Primax Diamond Application Guide for Jotun Primax Diamond Powder Coatings Date of Last Revision: August 2017 Page 1 of 7 Contents 1.0 Introduction 3 2.0 General overview 3 3.0 Safety Considerations..3

More information

--> Buy True-PDF --> Auto-delivered in 0~10 minutes. FZ/T

--> Buy True-PDF --> Auto-delivered in 0~10 minutes. FZ/T Translated English of Chinese Standard: FZ/T50010.13-2011 www.chinesestandard.net Sales@ChineseStandard.net NATIONAL TEXTILE INDUSTRY STANDARD OF THE PEOPLE S REPUBLIC OF CHINA FZ ICS 59.060.20 W 50 FZ/T

More information

Section 914. JOINT AND WATERPROOFING MATERIALS

Section 914. JOINT AND WATERPROOFING MATERIALS 914.01 Section 914. JOINT AND WATERPROOFING MATERIALS 914.01. General Requirements. Joint and waterproofing material for use in concrete construction must meet the requirements of this section. 914.02.

More information

Surface Finishes. For woods metals and plastics

Surface Finishes. For woods metals and plastics Surface Finishes For woods metals and plastics Reasons for Surface Finishes Some kind of surface finish is always necessary for the following reasons Resistance to decay (Stopping the material from rotting

More information

PRODUCT GUIDE: COMPLIANT TOPCOATS. Version:

PRODUCT GUIDE: COMPLIANT TOPCOATS. Version: PRODUCT GUIDE: COMPLIANT TOPCOATS Version: 08.07.17 EAGLE BRIDGES PRODUCT DATA PRODUCT: 3.5 V.O.C FASTDRY, Black Product Number: 4899 DESCRIPTION: This product is a high gloss enamel for OEM finishing

More information

BIS or used as a STANDARD comments is

BIS or used as a STANDARD comments is Draft for Comments Only Draft Indian Standard VAULT (STRONG ROOM) DOORS PART 1-SPECIFIATION (Second Revision) Not to be reproduced without the permission of Last date for receipt of BIS or used as a STANDARD

More information

ISO 3251 INTERNATIONAL STANDARD. Paints, varnishes and plastics Determination of non-volatile-matter content

ISO 3251 INTERNATIONAL STANDARD. Paints, varnishes and plastics Determination of non-volatile-matter content INTERNATIONAL STANDARD ISO 3251 Fourth edition 2008-02-15 Paints, varnishes and plastics Determination of non-volatile-matter content Peintures, vernis et plastiques Détermination de l'extrait sec Reference

More information

NAME OF THE COMMENTATOR/ORGANIZATION: Doc. No.: PG 20(1020) TITLE: Dimensions for relief grooves (second revision of IS 3428)

NAME OF THE COMMENTATOR/ORGANIZATION: Doc. No.: PG 20(1020) TITLE: Dimensions for relief grooves (second revision of IS 3428) NAME OF THE COMMENTATOR/ORGANIZATION: Doc. No.: PG 20(1020) TITLE: Dimensions for relief grooves (second revision of IS 3428) Sl. No. Clause/Sub-clause/ para/table/fig.no. Commented Comments * For Bureau

More information

CUSTOMER SUPPORT SAMPLE PREPARATION GUIDE FOR PAINT AND COATINGS (DATACOLOR FORMULATION SOFTWARE)

CUSTOMER SUPPORT SAMPLE PREPARATION GUIDE FOR PAINT AND COATINGS (DATACOLOR FORMULATION SOFTWARE) CUSTOMER SUPPORT SAMPLE PREPARATION GUIDE FOR PAINT AND COATINGS (DATACOLOR FORMULATION SOFTWARE) I II III IV V VI Overview Glossary of Words and Terminology Materials to be brought to the User s Course

More information

Technical Data Sheet Primers/Surfacers LV 250 Primer EP /005 FOR PROFESSIONAL USE ONLY

Technical Data Sheet Primers/Surfacers LV 250 Primer EP /005 FOR PROFESSIONAL USE ONLY 100 2505-001/005 50 2505-104 40 2505-204 2505-205 12 Description: Autocoat BT LV 250 Primer EP is a quick drying, chromate-free high solid two-pack epoxy primer-surfacer for shot blasted steel substrates..

More information

AquaCLAD Water-Reducible Rust Preventative Alkyd

AquaCLAD Water-Reducible Rust Preventative Alkyd AquaCLAD 1600 Water-Reducible Rust Preventative Alkyd A rust preventative coating for interior and exterior steel in mild to moderate industrial environment. Recommended For Features Refinish Market High

More information

DMS-8220, Hot Applied Thermoplastic

DMS-8220, Hot Applied Thermoplastic Overview Effective Date: August 2004 August 2007 (refer to 'Archived Versions' for previous versions). This Specification governs for the materials, composition, quality, sampling, and testing of thermoplastic

More information

Technical Data Sheet ACRYLIC FILLER 4:1 Acrylic filler with anti-corrosion additives RELATED PRODUCTS. Acrylic and polyurethane thinner

Technical Data Sheet ACRYLIC FILLER 4:1 Acrylic filler with anti-corrosion additives RELATED PRODUCTS. Acrylic and polyurethane thinner Acrylic filler with anti-corrosion additives RELATED PRODUCTS Acrylic filler hardener Acrylic and polyurethane thinner PROPERTIES A product designed and dedicated for renovation of classic cars Universal

More information

SECTION PAINTING

SECTION PAINTING SECTION 09900 PAINTING PART 1 - GENERAL 1.1 SECTION INCLUDES A. This Section includes surface preparation, painting, and finishing of new and existing wood, interior and exterior surfaces including the

More information

MATERIAL AND EQUIPMENT STANDARD FOR CHLORINATED RUBBER INHIBITIVE PRIMER ORIGINAL EDITION NOV. 1993

MATERIAL AND EQUIPMENT STANDARD FOR CHLORINATED RUBBER INHIBITIVE PRIMER ORIGINAL EDITION NOV. 1993 MATERIAL AND EQUIPMENT STANDARD FOR CHLORINATED RUBBER INHIBITIVE PRIMER ORIGINAL EDITION NOV. 1993 This standard specification is reviewed and updated by the relevant technical committee on Jan. 1999.

More information

SPECIFICATION FOR PAINTING ON GALVANIZED SURFACES BY WET/ELECTROSTATIC POWDER PAINTING

SPECIFICATION FOR PAINTING ON GALVANIZED SURFACES BY WET/ELECTROSTATIC POWDER PAINTING CHIEF CHEMIST DEPT. PAGE No. 1 SPECIFICATION FOR PAINTING ON GALVANIZED SURFACES BY WET/ELECTROSTATIC POWDER PAINTING 1. SCOPE This specification covers the requirements for painting of steel surfaces

More information

(H) PAINTING LIST OF BUREAU OF INDIAN STANDARD CODE OF PRACTICE (ISI)

(H) PAINTING LIST OF BUREAU OF INDIAN STANDARD CODE OF PRACTICE (ISI) (H) PAINTING LIST OF BUREAU OF INDIAN STANDARD CODE OF PRACTICE (ISI) 6278 : Code of Practice for white washing and colour washing. 2932 : Enamel and synthetic, exterior (a) Undercoating (b) Finsihing.

More information

Product Data Sheet November 2016

Product Data Sheet November 2016 Product Data Sheet November 2016 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY T8500V HP Chromate Free Epoxy Primer P580-3501/-3502/-3503/-3504 Product Description P580-3501 HP Chromate Free Epoxy Primer

More information

Data Sheet K-Aqua Silk Matt Enamel K-Aqua Seidenmattlack K-Aqua Hardener Properties. Material description.

Data Sheet K-Aqua Silk Matt Enamel K-Aqua Seidenmattlack K-Aqua Hardener Properties. Material description. 0 Enamel 2388 2K-Aqua Seidenmattlack 2388 Englisch water-based, two-component, highly resistant to mechanical and chemical stress, AgBB certified, for interior and exterior use, with 2K-Aqua Hardener 2380

More information

001: 2007 CEB STANDARD

001: 2007 CEB STANDARD 001: 2007 CEB STANDARD ALUMINIUM RE-DRAW RODS FOR ELECTRICAL PURPOSES CEYLON ELECTRICITY BOARD SRI LANKA Specification for ALUMINIUM RE-DRAW RODS FOR ELECTRICAL PURPOSES CEB Standard 001: 2007 CEYLON ELECTRICITY

More information

PRODUCT GUIDE: CATALYZED PRIMERS. Version:

PRODUCT GUIDE: CATALYZED PRIMERS. Version: PRODUCT GUIDE: CATALYZED PRIMERS Version: 08.07.17 305 Zinc Rich Epoxy Polyamide Primer Description: 305 is a user friendly zinc-rich epoxy primer formulated for use as a primer under acrylic, epoxy, and

More information

ISO INTERNATIONAL STANDARD. Road vehicles Pneumatic braking systems Part 1: Pipes, male fittings and tapped holes with facial sealing surface

ISO INTERNATIONAL STANDARD. Road vehicles Pneumatic braking systems Part 1: Pipes, male fittings and tapped holes with facial sealing surface INTERNATIONAL STANDARD ISO 4039-1 First edition 1998-08-15 Road vehicles Pneumatic braking systems Part 1: Pipes, male fittings and tapped holes with facial sealing surface Véhicules routiers Dispositifs

More information

HP Epoxy Primer P

HP Epoxy Primer P Product Data Sheet September 2006 (updated November 2016) INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY HP Epoxy Primer P580-3005 Product Description P580-3005 HP Epoxy Primer P275-3022 Hardener for Epoxy

More information

Our Ref: SRO/BM/C Date:

Our Ref: SRO/BM/C Date: Our Ref: SRO/BM/C Date: 03.04.2009 Subject: 1.Extension of existing partition and providing false ceiling in HSROL Sect. 2. Providing Partition and false ceiling in Sample Cell. To: Dear Sir(s), Quotation(s)

More information

CITY OF TOMBALL. Section FIRE HYDRANTS 1.01 SECTION INCLUDES. A. Fire hydrants. B. Adjustment of fire hydrants and gate valves.

CITY OF TOMBALL. Section FIRE HYDRANTS 1.01 SECTION INCLUDES. A. Fire hydrants. B. Adjustment of fire hydrants and gate valves. Section 02520 PART 1 G E N E R A L 1.01 SECTION INCLUDES A. Fire hydrants. B. Adjustment of fire hydrants and gate valves. 1.02 MEASUREMENT AND PAYMENT A. Unit Prices. 1. Payment is on a unit price basis

More information

ELECTRICAL NETWORKS SPECIFICATION TECHNICAL SPECIFICATION FOR A 230V/110V AND 400V/110V TRANSFORMER

ELECTRICAL NETWORKS SPECIFICATION TECHNICAL SPECIFICATION FOR A 230V/110V AND 400V/110V TRANSFORMER Approval Amendment Record Approval Date Version Description 03/05/2017 1 Initial issue PRINTOUT MAY NOT BE UP-TO-DATE; REFER TO METRO INTRANET FOR THE LATEST VERSION Page 1 of 13 Table of Contents 1. Purpose...

More information

Offset Inks - Basics

Offset Inks - Basics Offset Inks - Basics Lithographic inks are paste inks, The press works the ink, thereby heating it and reducing its viscosity or body, making it flow readily to provide a uniform ink film to the image

More information

SPECIFICATION FOR 11 KV CLASS, 24/15.7, 30/19.7 & 45/29.5 AMPS SPECIAL DESIGN TRANSFORMERS.

SPECIFICATION FOR 11 KV CLASS, 24/15.7, 30/19.7 & 45/29.5 AMPS SPECIAL DESIGN TRANSFORMERS. SPECIFICATION FOR 11 KV CLASS, 24/15.7, 30/19.7 & 45/29.5 AMPS SPECIAL DESIGN TRANSFORMERS. 1. SCOPE: This specification covers design, manufacture, testing and supply of 6.64/10.12 KV 24/15.7, 30/19.7

More information