Via Stitching. Contents

Size: px
Start display at page:

Download "Via Stitching. Contents"

Transcription

1 Via Stitching Contents

2 Adding Stitching Vias to a Net Stitching Parameters Clearance from Same-net Objects and Edges Clearance from Other-net Objects Notes Via Style

3

4 Related Videos Stitching Vias Via stitching is a technique used to tie together larger copper areas on different layers, in effect creating a strong vertical connection through the board structure, helping maintain a low impedance and short return loops. In RF designs stitching is used in combination with guard rings to create a via wall, helping create an electromagnetically 'quiet' PCB. Via stitching can also be used to tie areas of copper that might otherwise be isolated from their net, to that net. An area of the board where stitching vias have been added. Adding Stitching Vias to a Net

5 Select the Tools» Via Stitching» Auto Stitch Net command to automatically add stitching vias to the specified net across the board. Via stitching is run as a post-process, filling free areas of copper with stitching vias. For via stitching to occur, there must be overlapping regions of copper that are attached to the specified net, on different layers. Supported regions of copper include Fills, Polygons and Power Planes. Select the Tools» Via Stitching» Auto Stitch Net command from the menus to add stitching vias to a specific net. The Add Stitching to Net dialog will open, where the Stitching Parameters and Via Style are specified. Using the selected net, the stitching algorithm identifies all Fills, Polygons and Power Planes attached to that net and attempts to connect them through the board, using the specified via and stitching pattern. The via stitching algorithm treats Polygons, Fills and Planes in the following way: Polygons and Fills that are on the same net are stitched wherever they overlap on different layers. If there are Polygons or Fills on other nets that are overlapping within that area (on another layer), stitching is not applied in that region. Overlapping Plane regions on other nets are passed through. Overlapping Plane regions on the target net are always stitched, regardless of the presence of Plane regions (on another layer) attached to other nets. Rule 1 above applies if there are Polygons or Fills overlapping in the same region. Stitching Parameters

6 The stitching parameters control the stitching vias' placement pattern, and their clearance from other-net and same-net objects. Net - Select the Net to be used for stitching first as this effects the behavior of other options, such as clicking the Load values from Routing Via Style Rule button. Grid - the distance between the center of adjacent stitching vias. Stitching vias will not be placed in violation of applicable design rules, if a potential via site would result in a violation that site is skipped. Stagger alternate rows - alternate rows of stitching vias are offset by half of the Grid value. Clearance from Same-net Objects and Edges There are 2 ways of controlling the clearance of stitching vias, to vias and pads on the same net. Either the applicable Clearance design rule is used, or the Default Via/Pad Clearance specified here in the dialog is used. If a rule exists, then the tighter of these 2 settings is used. These options behave as follows: Default Via/Pad Clearance - stitching vias are only placed on potential stitching sites if this much clearance exists. Since potential stitching sites are determined by the stitching grid, it is likely they will be further than apart than this setting. Create New Clearance Rule - a stitching via -versus- other via/pad design rule is created when this button is clicked. This rule setting is used to ensure a potential stitching site is valid. When the button is clicked the PC B Rules and Constraints Editor opens, so that the rule Constraints can be set. Note that the rule is named and scoped to target the net selected in the Add Stitching to Net dialog. Edit Clearance Rule - this will be the button text if an applicable design rule already exists. Click to change the rule Constraint settings. Min Boundary Clearance - stitching vias are only placed on potential stitching sites if this much clearance exists to the edge of Polygon/Fill/Plane regions. Clearance from Other-net Objects The clearance from a stitching via to objects on other nets is controlled by the applicable clearance design rule. A stitching via will not be placed on a potential stitching site if it will violate the applicable design rule. Via Style The stitching Via Style can be configured manually in the Add Stitching to Net dialog, or imported from the applicable Routing Via Style design rule by clicking the Load values from Routing Via Style Rule button. Clicking this button will load the Preferred rule settings. Notes Once stitching is complete, you will need to re-pour the polygons if the applicable Polygon Connect Style design rule specifies a relief connection style. Each set of stitching vias are added to a union. The set can be removed by running the Tools» Via Stitching» Remove Via Stitching Group command, then clicking on any via in the group.

Printed Electronic Design

Printed Electronic Design Published on Online Documentation for Altium Products (https://www.altium.com/documentation) Home > Printed Electronics Using Altium Documentation Modified by Phil Loughhead on Dec 11, 2018 Printed Electronic

More information

Published on Online Documentation for Altium Products (http://www.altium.com/documentation)

Published on Online Documentation for Altium Products (http://www.altium.com/documentation) Published on Online Documentation for Altium Products (http://www.altium.com/documentation) Главная > Controlled Depth Drilling, or Back Drilling Новая эра документации Modified by Jun Chu on Apr 11, 2017

More information

PCB Layout. Date : 22 Dec 05. Prepare by : HK Sim Prepare by : HK Sim

PCB Layout. Date : 22 Dec 05. Prepare by : HK Sim Prepare by : HK Sim PCB Layout Date : 22 Dec 05 Main steps from Schematic to PCB Move from schematic to PCB Define PCB size Bring component from schematic to PCB Move the components to the desire position Layout the path

More information

Chapter 16 PCB Layout and Stackup

Chapter 16 PCB Layout and Stackup Chapter 16 PCB Layout and Stackup Electromagnetic Compatibility Engineering by Henry W. Ott Foreword The PCB represents the physical implementation of the schematic. The proper design and layout of a printed

More information

Impedance-Controlled Routing. Contents

Impedance-Controlled Routing. Contents Impedance-Controlled Routing Contents Do I Need Impedance Controlled Routing? How do I Control the Impedances? Impedance Matching the Components What Determines the Routing Impedance? Calculating the Routing

More information

Chapter 12: Electronic Circuit Simulation and Layout Software

Chapter 12: Electronic Circuit Simulation and Layout Software Chapter 12: Electronic Circuit Simulation and Layout Software In this chapter, we introduce the use of analog circuit simulation software and circuit layout software. I. Introduction So far we have designed

More information

Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece

Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece 1 Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece In this Module, we will explore the method of adding dovetail seams to curved edges such as the circumferential edge of a

More information

Stratigraphy Modeling Boreholes and Cross. Become familiar with boreholes and borehole cross sections in GMS

Stratigraphy Modeling Boreholes and Cross. Become familiar with boreholes and borehole cross sections in GMS v. 10.3 GMS 10.3 Tutorial Stratigraphy Modeling Boreholes and Cross Sections Become familiar with boreholes and borehole cross sections in GMS Objectives Learn how to import borehole data, construct a

More information

Stratigraphy Modeling Boreholes and Cross Sections

Stratigraphy Modeling Boreholes and Cross Sections GMS TUTORIALS Stratigraphy Modeling Boreholes and Cross Sections The Borehole module of GMS can be used to visualize boreholes created from drilling logs. Also three-dimensional cross sections between

More information

Display and Draw Features

Display and Draw Features CHAPTER 7 Display and Draw Features 7.1 Overview Feature / Function Tool Display or draw DTM features, such as contours, triangles, lattices, voids, islands, etc. DTM Menu Bar Load > DTM Features GEOPAK

More information

PADS Layout for an Integrated Project. Student Workbook

PADS Layout for an Integrated Project. Student Workbook Student Workbook 2017 Mentor Graphics Corporation All rights reserved. This document contains information that is trade secret and proprietary to Mentor Graphics Corporation or its licensors and is subject

More information

Ansoft Designer Tutorial ECE 584 October, 2004

Ansoft Designer Tutorial ECE 584 October, 2004 Ansoft Designer Tutorial ECE 584 October, 2004 This tutorial will serve as an introduction to the Ansoft Designer Microwave CAD package by stepping through a simple design problem. Please note that there

More information

Import/Export of tendons in module StatiCa Tendon

Import/Export of tendons in module StatiCa Tendon IDEA Tutorial Import/Export of tendons in module StatiCa Tendon by using formats DXF, TXT and table format Import/Export of tendons in module StatiCa Tendon 1 Contents 1. Terminology... 2 2. Import...

More information

Revit Structure 2012 Basics:

Revit Structure 2012 Basics: SUPPLEMENTAL FILES ON CD Revit Structure 2012 Basics: Framing and Documentation Elise Moss autodesk authorized publisher SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Structural

More information

Plated Through Hole Components. Padstack. Curso Prof. Andrés Roldán Aranda. 4º Curso Grado en Ingeniería de Tecnologías de Telecomunicación

Plated Through Hole Components. Padstack. Curso Prof. Andrés Roldán Aranda. 4º Curso Grado en Ingeniería de Tecnologías de Telecomunicación Plated Through Hole Components Padstack Curso 15-16 Prof. Andrés Roldán Aranda 4º Curso Grado en Ingeniería de Tecnologías de Telecomunicación 1.- Arquitectura del Pad 2.- Conceptos 3.- Tipología de Pads

More information

Gerber Setup. Modified by Susan Riege on 4-Aug Parent page: WorkspaceManager Dialogs

Gerber Setup. Modified by Susan Riege on 4-Aug Parent page: WorkspaceManager Dialogs Gerber Setup Modified by Susan Riege on 4-Aug-2015 Parent page: WorkspaceManager Dialogs Other Related Resources Options for Project - Options Tab (Dialog) Generate Output Files (Dialog) Aperture (Dialog)

More information

Revit Structure 2013 Basics

Revit Structure 2013 Basics Revit Structure 2013 Basics Framing and Documentation Elise Moss Supplemental Files SDC P U B L I C AT I O N S Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Tutorial

More information

White paper. High speed and RF PCB routing : Best practises and recommandations

White paper. High speed and RF PCB routing : Best practises and recommandations ALCIOM 5, Parvis Robert Schuman 92370 CHAVILLE - FRANCE Tel/Fax : 01 47 09 30 51 contact@alciom.com www.alciom.com Projet : White paper DOCUMENT : High speed and RF PCB routing : Best practises and recommandations

More information

Release Notes - Fixes in Tekla Structures 2016i PR1

Release Notes - Fixes in Tekla Structures 2016i PR1 Release Notes - Fixes in Tekla Structures 2016i PR1, you can now set the to either or. is modified., the ID of the connection plate is not changed anymore when the connection now uses normal rebar groups

More information

Published on Online Documentation for Altium Products (http://www.altium.com/documentation)

Published on Online Documentation for Altium Products (http://www.altium.com/documentation) Published on Online Documentation for Altium Products (http://www.altium.com/documentation) Home > Gerber Setup A New Era for Documentation Modified by Phil Loughhead on Jun 17, 2017 The Gerber Setup dialog

More information

Release Notes - Fixes in Tekla Structures 2016i SP1

Release Notes - Fixes in Tekla Structures 2016i SP1 Release Notes - Fixes in Tekla Structures 2016i SP1 is modified., the ID of the connection plate is not changed anymore when the connection now uses normal rebar groups instead of tapered groups., the

More information

PCB Layout in the Xpedition Flow. Student Workbook

PCB Layout in the Xpedition Flow. Student Workbook PCB Layout in the Xpedition Flow Student Workbook Mentor Graphics Corporation All rights reserved. This document contains information that is trade secret and proprietary to Mentor Graphics Corporation

More information

Stitching MetroPro Application

Stitching MetroPro Application OMP-0375F Stitching MetroPro Application Stitch.app This booklet is a quick reference; it assumes that you are familiar with MetroPro and the instrument. Information on MetroPro is provided in Getting

More information

[Use Element Selection tool to move raster towards green block.]

[Use Element Selection tool to move raster towards green block.] Demo.dgn 01 High Performance Display Bentley Descartes has been designed to seamlessly integrate into the Raster Manager and all tool boxes, menus, dialog boxes, and other interface operations are consistent

More information

Figure Main frame of IMNLab.

Figure Main frame of IMNLab. IMNLab Tutorial This Tutorial guides the user to go through the design procedure of a wideband impedance match network for a real circuit by using IMNLab. Wideband gain block TQP3M97 evaluation kit from

More information

Noise Constraint Driven Placement for Mixed Signal Designs. William Kao and Wenkung Chu October 20, 2003 CAS IEEE SCV Meeting

Noise Constraint Driven Placement for Mixed Signal Designs. William Kao and Wenkung Chu October 20, 2003 CAS IEEE SCV Meeting Noise Constraint Driven Placement for Mixed Signal Designs William Kao and Wenkung Chu October 20, 2003 CAS IEEE SCV Meeting Introduction OUTLINE Substrate Noise: Some Background Substrate Noise Network

More information

Estimated Time Required to Complete: 45 minutes

Estimated Time Required to Complete: 45 minutes Estimated Time Required to Complete: 45 minutes This is the first in a series of incremental skill building exercises which explore sheet metal punch ifeatures. Subsequent exercises will address: placing

More information

5 TIPS FOR SPECIFYING PCB HOLE SIZE TOLERANCE

5 TIPS FOR SPECIFYING PCB HOLE SIZE TOLERANCE One of the more forgotten topics in PCB design are the holes through which components are mounted. Specifying the tolerance of hole dimensions in PCB fabrication ensures proper fit of plated-through-hole

More information

HOW SMALL PCB DESIGN TEAMS CAN SOLVE HIGH-SPEED DESIGN CHALLENGES WITH DESIGN RULE CHECKING MENTOR GRAPHICS

HOW SMALL PCB DESIGN TEAMS CAN SOLVE HIGH-SPEED DESIGN CHALLENGES WITH DESIGN RULE CHECKING MENTOR GRAPHICS HOW SMALL PCB DESIGN TEAMS CAN SOLVE HIGH-SPEED DESIGN CHALLENGES WITH DESIGN RULE CHECKING MENTOR GRAPHICS H I G H S P E E D D E S I G N W H I T E P A P E R w w w. p a d s. c o m INTRODUCTION Coping with

More information

Lesson 6 2D Sketch Panel Tools

Lesson 6 2D Sketch Panel Tools Lesson 6 2D Sketch Panel Tools Inventor s Sketch Tool Bar contains tools for creating the basic geometry to create features and parts. On the surface, the Geometry tools look fairly standard: line, circle,

More information

Appliqué with CutWork

Appliqué with CutWork Appliqué with CutWork Method 1: Creating Appliqué from a Placement Line Open BERNINA Embroidery Software. Click on File> Open. Select the Appliqué Flowers, provided with the lesson. Click on Open. Select

More information

1.6.7 Add Arc Length Dimension Modify Dimension Value Check the Sketch Curve Connectivity

1.6.7 Add Arc Length Dimension Modify Dimension Value Check the Sketch Curve Connectivity Contents 2D Sketch... 1 1.1 2D Sketch Introduction... 1 1.1.1 2D Sketch... 1 1.1.2 Basic Setting of 2D Sketch... 2 1.1.3 Exit 2D Sketch... 4 1.2 Draw Common Geometry... 5 2.2.1 Points... 5 2.2.2 Lines

More information

ME Week 2 Project 2 Flange Manifold Part

ME Week 2 Project 2 Flange Manifold Part 1 Project 2 - Flange Manifold Part 1.1 Instructions This project focuses on additional sketching methods and sketching commands. Revolve and Work features are also introduced. The part being modeled is

More information

Transient Data Acquisition System, TAS 4-40 Potential-free measurement of fast rise pulses:

Transient Data Acquisition System, TAS 4-40 Potential-free measurement of fast rise pulses: Transient Data Acquisition System, TAS 4-40 Potential-free measurement of fast rise pulses: High precision measurement of fast rising voltages and currents causes considerable problems in many spheres

More information

AutoCAD 2D I. Module 16. Isometric and Dimensioning. IAT Curriculum Unit PREPARED BY. January 2011

AutoCAD 2D I. Module 16. Isometric and Dimensioning. IAT Curriculum Unit PREPARED BY. January 2011 AutoCAD 2D I Module 16 Isometric and Dimensioning PREPARED BY IAT Curriculum Unit January 2011 Institute of Applied Technology, 2011 Module 16 Auto CAD Self-paced Learning Modules AutoCAD 2D Isometric

More information

An Introduction to Dimensioning Dimension Elements-

An Introduction to Dimensioning Dimension Elements- An Introduction to Dimensioning A precise drawing plotted to scale often does not convey enough information for builders to construct your design. Usually you add annotation showing object measurements

More information

How to combine images in Photoshop

How to combine images in Photoshop How to combine images in Photoshop In Photoshop, you can use multiple layers to combine images, but there are two other ways to create a single image from mulitple images. Create a panoramic image with

More information

Digital Photography 1

Digital Photography 1 Digital Photography 1 Photoshop Lesson 3 Resizing and transforming images Name Date Create a new image 1. Choose File > New. 2. In the New dialog box, type a name for the image. 3. Choose document size

More information

Revit Structure 2014 Basics

Revit Structure 2014 Basics Revit Structure 2014 Basics Framing and Documentation Elise Moss Authorized Author SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit

More information

High Point Communications Authorized dealer for USA Fleet Services

High Point Communications Authorized dealer for USA Fleet Services Summary of Display Features Idle Alert - Idle alerts can be sent every 10 minutes (up to 60 minutes) Stop Duration Alert Stop Duration alerts can be sent every 10 minutes (up to 60 minutes), after 24 hours,

More information

Processing Gerber Files in CircuitPro

Processing Gerber Files in CircuitPro Processing Gerber Files in CircuitPro Requirements 1. Circuit Pro version 1.5 revision 164 or higher 2. Set of Gerber Files Process Steps 1. Execute Process Planning Wizard. a. Press the process planning

More information

Levels. Chapter Nine PLAY VIDEO INTRODUCTION LEVEL MANAGER AND LEVEL DISPLAY DIALOGS LEVEL MANAGER DIALOG

Levels. Chapter Nine PLAY VIDEO INTRODUCTION LEVEL MANAGER AND LEVEL DISPLAY DIALOGS LEVEL MANAGER DIALOG Chapter Nine Levels PLAY VIDEO INTRODUCTION A design file consists of any number of levels. A level is a way of separating CAD data much the same way as a clear sheet of acetate is used by an architect

More information

PASS Sample Size Software

PASS Sample Size Software Chapter 945 Introduction This section describes the options that are available for the appearance of a histogram. A set of all these options can be stored as a template file which can be retrieved later.

More information

Radial dimension objects are available for placement in the PCB Editor only. Use one of the following methods to access a placement command:

Radial dimension objects are available for placement in the PCB Editor only. Use one of the following methods to access a placement command: Radial Dimension Old Content - visit altium.com/documentation Modified by on 20-Nov-2013 Parent page: Objects A placed Radial Dimension. Summary A radial dimension is a group design object. It allows for

More information

Welcome to Solid Edge University

Welcome to Solid Edge University #SEU15 Welcome to Solid Edge University Realize innovation. State-of-the-Art Drafting, Made Even Better Investing in What You Need General Workflow Dimension Enhancements Annotation Enhancements Page 2

More information

FPGA SI Tutorial - Simulating the Reflection Characteristics

FPGA SI Tutorial - Simulating the Reflection Characteristics FPGA SI Tutorial - Simulating the Reflection Characteristics Old Content - visit altium.com/documentation Modified by Admin on Sep 13, 2017 Now that things are setup we can simulate the reflection characteristics

More information

PCB Design Guidelines for Reduced EMI

PCB Design Guidelines for Reduced EMI PCB Design Guidelines for Reduced EMI Guided By: Prof. Ruchi Gajjar Prepared By: Shukla Jay (13MECE17) Outline Power Distribution for Two-Layer Boards Gridding Power Traces on Two-Layer Boards Ferrite

More information

2' x 3' Polymer Pull Box Cover 4'-0" 7'-0" 24" x 76" Access Opening 3'-6"

2' x 3' Polymer Pull Box Cover 4'-0 7'-0 24 x 76 Access Opening 3'-6 Scope.1 Precast Concrete Equipment Slab Box 8' x 10' x Pad with 4' x 7' x 3'- Box for 5-Way RAM Gas Switch, 2-Way, 3-Way, and 4-Way Pad-Mounted RAG Gas Switches, VFI 9, VFI 12, Bypass Switch, and 33 kv

More information

Page 1

Page 1 CONTENT INTRODUCTION 2 INPUT DATA FORMATS 3 INPUT DATA REQUIREMENTS 4 CLASSIFICATION 6 HOLES 8 COPPER LAYERS 10 BGAS 12 MECHANICAL LAYER 13 SOLDERMASK 15 LEGEND PRINT 17 CARBON 18 PEEL-OFF MASK 19 VIAFILL

More information

Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.

Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch. Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.

More information

Autodesk Inventor Module 17 Angles

Autodesk Inventor Module 17 Angles Inventor Self-paced ecourse Autodesk Inventor Module 17 Angles Learning Outcomes When you have completed this module, you will be able to: 1 Describe drawing inclined lines, aligned and angular dimensions,

More information

Converting a solid to a sheet metal part tutorial

Converting a solid to a sheet metal part tutorial Converting a solid to a sheet metal part tutorial Introduction Sometimes it is easier to start with a solid and convert it to create a sheet metal part. This tutorial will guide you through the process

More information

Autodesk Advance Steel. Drawing Style Manager s guide

Autodesk Advance Steel. Drawing Style Manager s guide Autodesk Advance Steel Drawing Style Manager s guide TABLE OF CONTENTS Chapter 1 Introduction... 5 Details and Detail Views... 6 Drawing Styles... 6 Drawing Style Manager... 8 Accessing the Drawing Style

More information

To apply proposed roadway data (vertical alignments, cross section template data, cut/fill slopes, etc.)

To apply proposed roadway data (vertical alignments, cross section template data, cut/fill slopes, etc.) That CAD Girl J ennifer dib ona Website: www.thatcadgirl.com Email: thatcadgirl@aol.com Phone: (919) 417-8351 Fax: (919) 573-0351 Roadway Design Extracting Existing Ground Cross Sections This document

More information

MEASUREMENT CAMERA USER GUIDE

MEASUREMENT CAMERA USER GUIDE How to use your Aven camera s imaging and measurement tools Part 1 of this guide identifies software icons for on-screen functions, camera settings and measurement tools. Part 2 provides step-by-step operating

More information

Nikon A1Rsi Confocal Start-Up Sequence

Nikon A1Rsi Confocal Start-Up Sequence 1. Turn the key on the Nikon LUN-V Laser Launch. Nikon A1Rsi Confocal Start-Up Sequence 2. Press the button the left side of the A1Rsi Controller unit. 3. Turn on the power strip underneath the microscope.

More information

EECAD s MUST List. Requests for drawing numbers MUST be submitted via the EECAD job request form at

EECAD s MUST List. Requests for drawing numbers MUST be submitted via the EECAD job request form at Customers are required to follow certain criteria for all designs whether they are ultimately done in EECAD or by the customers themselves. These criteria, approved by EES Management, are listed below:

More information

How to blend, feather, and smooth

How to blend, feather, and smooth How to blend, feather, and smooth Quite often, you need to select part of an image to modify it. When you select uniform geometric areas squares, circles, ovals, rectangles you don t need to worry too

More information

There are two types of cove light in terms of light distribution inside a room

There are two types of cove light in terms of light distribution inside a room DIALux evo Tutorials Tutorial 2 How to create a cove light detail In this tutorial you will learn the following commands. 1. Using help lines 2. Using ceiling. 3. Using cutout 4. Using Boolean operation

More information

Introduction to NI Multisim & Ultiboard Software version 14.1

Introduction to NI Multisim & Ultiboard Software version 14.1 School of Engineering and Applied Science Electrical and Computer Engineering Department Introduction to NI Multisim & Ultiboard Software version 14.1 Dr. Amir Aslani August 2018 Parts Probes Tools Outline

More information

Using EAGLE: Board Layout a

Using EAGLE: Board Layout a Using EAGLE: Board Layout a learn.sparkfun.com tutorial Available online at: http://sfe.io/t111 Contents Previously on Using EAGLE Layers Overview Arranging the Board Routing the Board Checking for Errors

More information

Allegro New Products - DFM / Rule Checkers

Allegro New Products - DFM / Rule Checkers Allegro New Products - DFM / Rule Checkers Eric / Graser 16 / Oct / 2015 Topic Allegro DFM Checker in Allegro PCB Manufacturing Option Allegro PCB Rules Developer / Checker Option PCB Design & Production

More information

Advance Steel. Drawing Style Manager s guide

Advance Steel. Drawing Style Manager s guide Advance Steel Drawing Style Manager s guide TABLE OF CONTENTS Chapter 1 Introduction...7 Details and Detail Views...8 Drawing Styles...8 Drawing Style Manager...9 Accessing the Drawing Style Manager...9

More information

CutWork Many Ways: Editing a Draw File

CutWork Many Ways: Editing a Draw File CutWork Many Ways: Editing a Draw File Notes: Opening the File Select the Apple.draw file. Click on Open. The CutWork apple appears on the screen and can be sent to the machine of your choice at this point

More information

Release Highlights for BluePrint-PCB Product Version 2.0.1

Release Highlights for BluePrint-PCB Product Version 2.0.1 Release Highlights for BluePrint-PCB Product Version 2.0.1 Introduction BluePrint Version 2.0.1 is a rolling release for BluePrint V2.0. BluePrint rolling releases are delivered as needed and allow us

More information

Basic Tutorial of Circuit Maker

Basic Tutorial of Circuit Maker Introduction Basic Tutorial of Circuit Maker In this course, we will be using the free student edition of a commercial program, CircuitMaker, to design and simulate logic circuits. Starting a New Design

More information

NX 7.5. Table of Contents. Lesson 3 More Features

NX 7.5. Table of Contents. Lesson 3 More Features NX 7.5 Lesson 3 More Features Pre-reqs/Technical Skills Basic computer use Completion of NX 7.5 Lessons 1&2 Expectations Read lesson material Implement steps in software while reading through lesson material

More information

Overcoming the Challenges of HDI Design

Overcoming the Challenges of HDI Design ALTIUMLIVE 2018: Overcoming the Challenges of HDI Design Susy Webb Design Science Sr PCB Designer San Diego Oct, 2018 1 Challenges HDI Challenges Building the uvia structures The cost of HDI (types) boards

More information

Introduction to ANSYS DesignModeler

Introduction to ANSYS DesignModeler Lecture 4 Planes and Sketches 14. 5 Release Introduction to ANSYS DesignModeler 2012 ANSYS, Inc. November 20, 2012 1 Release 14.5 Preprocessing Workflow Geometry Creation OR Geometry Import Geometry Operations

More information

Monoconical RF Antenna

Monoconical RF Antenna Page 1 of 8 RF and Microwave Models : Monoconical RF Antenna Monoconical RF Antenna Introduction Conical antennas are useful for many applications due to their broadband characteristics and relative simplicity.

More information

1. Create a 2D sketch 2. Create geometry in a sketch 3. Use constraints to position geometry 4. Use dimensions to set the size of geometry

1. Create a 2D sketch 2. Create geometry in a sketch 3. Use constraints to position geometry 4. Use dimensions to set the size of geometry 2.1: Sketching Many features that you create in Fusion 360 start with a 2D sketch. In order to create intelligent and predictable designs, a good understanding of how to create sketches and how to apply

More information

Modeling Basic Mechanical Components #1 Tie-Wrap Clip

Modeling Basic Mechanical Components #1 Tie-Wrap Clip Modeling Basic Mechanical Components #1 Tie-Wrap Clip This tutorial is about modeling simple and basic mechanical components with 3D Mechanical CAD programs, specifically one called Alibre Xpress, a freely

More information

Edge Blender Controller

Edge Blender Controller Edge Blender Controller Calibration Manual Version 2017 V1 Contents Contents INTRODUCTION 1 FEATURES 1 OS AND HARDWARE 1 INSTALLATION 2 INSTALLATION 2 UNINSTALLATION 4 INTERFACE 6 COMMUNICATION 7 CONFIG

More information

Release Highlights for BluePrint-PCB Product Version 1.8

Release Highlights for BluePrint-PCB Product Version 1.8 Release Highlights for BluePrint-PCB Product Version 1.8 Introduction BluePrint Version 1.8 Build 341 is a rolling release update. BluePrint rolling releases allow us to be extremely responsive to customer

More information

You can easily print images using the Capture NX print function. Here we will explain the process for printing

You can easily print images using the Capture NX print function. Here we will explain the process for printing Printing - Print Size Request How do you print images to fit on particular paper sizes. Response You can easily print images using the Capture NX print function. Here we will explain the process for printing

More information

Forensic Search. Version 3.5. Configuration Manual

Forensic Search. Version 3.5. Configuration Manual Forensic Search Version 3.5 en Configuration Manual 3 en Table of Contents Forensic Search Table of Contents 1 Introduction 5 2 Requirements 5 2.1 License 5 2.2 Limitations 7 2.3 The Basics 7 2.3.1 Objects

More information

Getting Started in Eagle Professional Schematic Software. Tyler Borysiak Team 9 Manager

Getting Started in Eagle Professional Schematic Software. Tyler Borysiak Team 9 Manager Getting Started in Eagle 7.3.0 Professional Schematic Software Tyler Borysiak Team 9 Manager 1 Executive Summary PCBs, or Printed Circuit Boards, are all around us. Almost every single piece of electrical

More information

VTube-LASER Quick Start Guide

VTube-LASER Quick Start Guide VTube-LASER Quick Start Guide This guide shows how to import a STEP file and then MEASURE and qualify demo tube 4 using the standard UNISCAN method of measuring. The steps in this workflow are from version

More information

Evaluation Chapter by CADArtifex

Evaluation Chapter by CADArtifex The premium provider of learning products and solutions www.cadartifex.com EVALUATION CHAPTER 2 Drawing Sketches with SOLIDWORKS In this chapter: Invoking the Part Modeling Environment Invoking the Sketching

More information

Batch Counting of Foci

Batch Counting of Foci Batch Counting of Foci Getting results from Z stacks of images. 1. First it is necessary to determine suitable CHARM parameters to be used for batch counting. First drag a stack of images taken with the

More information

1. Setup Output mode. 2. Using a Fixed tile size

1. Setup Output mode. 2. Using a Fixed tile size Tutorial Tiling Software version: Asanti 2.0 Document version: June 23, 2015 This tutorial demonstrates how to use tiling with Asanti. Tiling can only be executed on a system where Acrobat Pro X or later

More information

PCB DESIGN AND ASSEMBLY FOR POWER SUPPLIES

PCB DESIGN AND ASSEMBLY FOR POWER SUPPLIES PCB DESIGN AND ASSEMBLY FOR POWER SUPPLIES Power supplies come in large varieties, can have different topologies, and feature numerous safeguards. Design of printed circuit boards (PCBs) for powers supplies

More information

06/17/02 Page 1 of 12

06/17/02 Page 1 of 12 Understanding the Graphical User Interface When you start AutoCAD, the AutoCAD window opens. The window is your design work space. It contains elements that you use to create your designs and to receive

More information

EM Noise Mitigation in Electronic Circuit Boards and Enclosures

EM Noise Mitigation in Electronic Circuit Boards and Enclosures EM Noise Mitigation in Electronic Circuit Boards and Enclosures Omar M. Ramahi, Lin Li, Xin Wu, Vijaya Chebolu, Vinay Subramanian, Telesphor Kamgaing, Tom Antonsen, Ed Ott, and Steve Anlage A. James Clark

More information

Getting Started. Before You Begin, make sure you customized the following settings:

Getting Started. Before You Begin, make sure you customized the following settings: Getting Started Getting Started Before getting into the detailed instructions for using Generative Drafting, the following tutorial aims at giving you a feel of what you can do with the product. It provides

More information

Working with Detail Components and Managing DetailsChapter1:

Working with Detail Components and Managing DetailsChapter1: Chapter 1 Working with Detail Components and Managing DetailsChapter1: In this chapter, you learn how to use a combination of sketch lines, imported CAD drawings, and predrawn 2D details to create 2D detail

More information

Chapter 6 Title Blocks

Chapter 6 Title Blocks Chapter 6 Title Blocks In previous exercises, every drawing started by creating a number of layers. This is time consuming and unnecessary. In this exercise, we will start a drawing by defining layers

More information

IX Feb Operation Guide. Sequence Creation and Control Software SD011-PCR-LE. Wavy for PCR-LE. Ver. 5.5x

IX Feb Operation Guide. Sequence Creation and Control Software SD011-PCR-LE. Wavy for PCR-LE. Ver. 5.5x IX000693 Feb. 015 Operation Guide Sequence Creation and Control Software SD011-PCR-LE Wavy for PCR-LE Ver. 5.5x About This Guide This PDF version of the operation guide is provided so that you can print

More information

Split Planes in Multilayer PCBs

Split Planes in Multilayer PCBs by Barry Olney coulmn BEYOND DESIGN Split Planes in Multilayer PCBs Creating split planes or isolated islands in the copper planes of multilayer PCBs at first seems like a good idea. Today s high-speed

More information

Lesson 4 Holes and Rounds

Lesson 4 Holes and Rounds Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information

More information

SMT Module RF Reference Design Guide. AN_ SMT Module RF Reference Design Guide _V1.01

SMT Module RF Reference Design Guide. AN_ SMT Module RF Reference Design Guide _V1.01 SMT Module RF Reference Design Guide AN_ SMT Module RF Reference Design Guide _V1.01 Document Title: SMT Module RF Reference Design Guide Version: 1.01 Date: 2010-2-10 Status: Document Control ID: Release

More information

Three Steps to Dynamic View for BIM Applications

Three Steps to Dynamic View for BIM Applications Three Steps to Dynamic View for BIM Applications The process of creating and using dynamic views can seem daunting to even the most experienced user. The Bentley BIM applications provide tools to somewhat

More information

Print Test Card. Print Sample Card. The Reprint last card button sends a command to the printer to print the last card.

Print Test Card. Print Sample Card. The Reprint last card button sends a command to the printer to print the last card. Print Test Card Print Sample Card Note The sample cards in the Test Card Library are.bmp images stored in the following default location: C:\Documents and Settings\All Users\ZMotif\Library 1. View the

More information

Vectorworks Architect

Vectorworks Architect SAMPLE by Jonathan Pickup third edition written with version 2011 Vectorworks Architect Tutorial Manual Table of Contents Introduction... iii How to Use this Manual... iii New Ways of Drawing... iv Vectorworks

More information

Object Groups By Kyle Gillen (Last Updated 6/9/16)

Object Groups By Kyle Gillen (Last Updated 6/9/16) Object Groups By Kyle Gillen (Last Updated 6/9/16) What are they? Object Groups are a means of loading additional objects on top of your base terrains/main objects, without having to create additional

More information

House Design Tutorial

House Design Tutorial House Design Tutorial This House Design Tutorial shows you how to get started on a design project. The tutorials that follow continue with the same plan. When you are finished, you will have created a

More information

Exercise01: Circle Grid Obj. 2 Learn duplication and constrain Obj. 4 Learn Basics of Layers

Exercise01: Circle Grid Obj. 2 Learn duplication and constrain Obj. 4 Learn Basics of Layers 01: Make new document Details: 8 x 8 02: Set Guides & Grid Preferences Details: Grid style=lines, line=.5, sub=1 03: Draw first diagonal line Details: Start with the longest line 1st. 04: Duplicate first

More information

Parametric Drawing Using Constraints

Parametric Drawing Using Constraints CHAPTER 10 Parametric Drawing Using Constraints PROJECT EXERCISE This project exercise provides point-by-point instructions for creating the objects shown in Figure P10 1. In this exercise, you will apply

More information

TUTORIAL 4: Combined Axial and Bending Problem Sketch Path Sweep Initial Project Space Setup Static Structural ANSYS

TUTORIAL 4: Combined Axial and Bending Problem Sketch Path Sweep Initial Project Space Setup Static Structural ANSYS TUTORIAL 4: Combined Axial and Bending Problem In this tutorial you will learn how to draw a bar that has bends along its length and therefore will have both axial and bending stresses acting on cross-sections

More information

Introduction to Polylines and Multilines Chapter 15

Introduction to Polylines and Multilines Chapter 15 Introduction to Polylines and Multilines Chapter 15 Sacramento City College EDT 310 Chapter 15 - Introduction to Polylines and Multilines 1 Polylines Chapter 15 - Introduction to Polylines and Multilines

More information