MESP TECHNICAL SPECIFICATION FOR TRANSMISSION WIRE HARD-DRAWN COPPER 19/ mm 2

Transcription

1 Engineering Specification Electrical Networks TECHNICAL SPECIFICATION FOR TRANSMISSION WIRE HARD-DRAWN COPPER 19/ mm 2 Version: 1 Issued: January 2015 Owner: Engineering Division Approved By: Pat Kelly Head Engineer (Electrical) PRINTOUT MAY NOT BE UP-TO-DATE; REFER TO METRO INTRANET FOR THE LATEST VERSION

2 Approval Amendment Record Approval Date Version Description 15/01/ Initial issue under MTM. This document replaces Mainco Specification MESP 0004 Revision A. Rebranded & reformatted to reflect MTM PRINTOUT MAY NOT BE UP-TO-DATE; REFER TO METRO INTRANET FOR THE LATEST VERSION Page 2 of 7

3 Table of Contents 1. Purpose Scope Abbreviation Definitions References & Legislations Material Conductor Characteristics Lay Dimensions Pre-production Test Requirements Production Test Requirements Quality Assurance Warranty Packing Delivery... 7 PRINTOUT MAY NOT BE UP-TO-DATE; REFER TO METRO INTRANET FOR THE LATEST VERSION Page 3 of 7

4 1. Purpose This document details the specification of 70 mm² hard-drawn copper Transmission Wire 2. Scope The scope comprises the manufacture, testing, supply and delivery of 70 mm² hard-drawn copper Transmission Wire in accordance with this specification and to the entire satisfaction of Metro Trains Melbourne. 3. Abbreviation GPa Kg Km kn mm MPa Gigapascal Kilogram Kilometre Kilonewton Millimetre Megapascal 4. Definitions Lay Ratio The ratio of the lay length to the external diameter of the corresponding layer of wires 5. References & Legislations AS/NZS 1574 Copper and Copper Alloys - Wire for Electrical Purposes AS 2738 AS AS 3822 AS 2193 AS/NZS 2857 AS 1391 AS/NZS ISO 9001 Copper and Copper Alloys - Compositions and Designations of Refinery Products, Wrought Products, Ingots and Castings Conductors - Bare Overhead - Hard-Drawn Copper Test Methods for Bare Overhead Conductors Calibration and Classification of Force Measuring Systems Timber Drums for Insulated Electric Cables and Bare Conductors Metallic Materials Tensile Testing at Ambient Temperature Quality Management Systems - Requirements. PRINTOUT MAY NOT BE UP-TO-DATE; REFER TO METRO INTRANET FOR THE LATEST VERSION Page 4 of 7

5 6. Material a. The chemical composition of the material used for the solid conductor shall conform to AS 2738 alloy designation C11000 (Electrolytic tough pitch copper). b. The maximum resistivity at 20 C is micro ohm/metre (equivalent to a conductivity of 97% IACS). c. The minimum Ultimate Tensile Strength is 435MPa for the individual strands of the hard-drawn copper wire. The Ultimate Tensile Strength is given by d as per alloy designation C11000 in AS d. The wire shall be clean, smooth and free from all defects e. Joints shall be made in the soft rolled rod before drawing by cold pressure buttwelding, resistance butt-welding or resistance brazing. The wire at the joints shall comply with the requirements of Clauses b and c of this section. The minimum distance between two such joints in the conductor shall be 15m. f. The wire density at 20 C shall be 8,890 kg/m³ plus or minus 3%. 7. Conductor Characteristics The lay ratio affects the area, mass and resistance of conductors composed of stranded wires. The following stranding constants are multiplied with the corresponding property of a single strand to give the overall characteristic: Stranding constants: o Area: o Mass: Resistance: Strand Dia. (mm) Cross-sectional area (mm²) Mass/km (kg) Calculated breaking load (kn) DC 20 C (ohms) 2.14 (nom) (-1%) The Calculated Break Load of the conductor is 90% of the sum of the strengths of the individual strands before stranding. This is based on a minimum Ultimate Tensile Strength of d MPa where d is the diameter of the strand in millimeters. Modulus of elasticity may be taken as 110GPa. This value is obtained after the initial stretch of the wire following construction. Coefficient of linear expansion may be taken as 17x10-6 per C. PRINTOUT MAY NOT BE UP-TO-DATE; REFER TO METRO INTRANET FOR THE LATEST VERSION Page 5 of 7

6 8. Lay Lay ratio and direction of the two layers shall be: 6-wire layer: 10 min, 17 max. Left-hand lay 12-wire layer: 10 min, 16 max. Right-hand lay 9. Dimensions Wire size and tolerances shall be in accordance with AS For a 19/2.14 nominal conductor of 70mm² nominal cross-sectional area the overall wire diameter shall be 10.7mm +/- 1%. 10. Pre-production Test Requirements Mechanical, resistivity and suitable metallurgical tests shall be performed on samples of wire joints produced using identical parameters to final production condition. 11. Production Test Requirements For the purposes of this specification the metallurgical tests shall be in accordance with AS/NZS Mechanical and electrical tests shall be in accordance with AS and AS Quality Assurance The Supplier should meet the requirements of AS/NZS ISO Warranty The Supplier shall provide a Certificate of Conformance together with a full test report as stipulated in Production Test Requirements. 14. Packing a) The transmission wire shall be wound without twists, or kinks, on drums of approved design and of sufficient size to prevent sharp bends and shall be properly protected against damage in transit. b) Typically approved design is wooden drums lined with sisal-craft in general accordance with AS 2857 and the following Metro Trains Melbourne required dimensions: o Barrel diameter 500mm minimum o Overall diameter 1000mm maximum o Overall width 650mm maximum A mild steel reinforcing plate 400mm 2 by 6.4mm thick shall be bolted to the middle of each side of the drum with a minimum of 6 bolts. An 83mm square hole shall be provided in the drum and reinforcing plates to take a 76mm spindle. PRINTOUT MAY NOT BE UP-TO-DATE; REFER TO METRO INTRANET FOR THE LATEST VERSION Page 6 of 7

7 The free ends of the wire shall be suitably treated to prevent de-stranding. The inner end of the conductor shall be passed through the drum flange to the outside and stapled securely. The outer end of the conductor shall be secured to the inside of the drum flange with staples and bent back on itself to prevent it from working loose. c) Metro Trains Melbourne shall specify the length of the conductor on each drum. d) The following information shall be legibly and indelibly marked on the flange of the drums or a label securely attached thereto: (i) (ii) (iii) (iv) (v) (vi) (vii) (viii) Supplier s name Supplier s drum serial number The conductor material and size (Hard-drawn copper, transmission wire 19/2.14, 70mm2) Length of conductor Gross mass of conductor and drum Handling or lifting instructions. The preferred method being by means of a spindle through the spindle holes and a spreader to prevent damage to the flanges An arrow with the words 'ROLL THIS WAY' to indicate the direction in which the drum should be rolled on the flanges The Metro Trains Melbourne contract number, order number and specification number e) Alternative equivalent or superior packing system may be submitted to Metro Trains Melbourne for consideration. 15. Delivery Transmission wires shall be delivered free into Metro Trains Melbourne Central Store. The Central Store is located at E-Gate, Footscray Road, West Melbourne, Victoria 3051 and delivery shall take place during business hours Monday to Friday (except Public Holidays) from 0800 till Metro Trains Melbourne shall be notified of any delivery 5-working days prior to delivery. PRINTOUT MAY NOT BE UP-TO-DATE; REFER TO METRO INTRANET FOR THE LATEST VERSION Page 7 of 7