Temperature Controller Replacement
|
|
- Earl Shields
- 5 years ago
- Views:
Transcription
1 DRSC & R Series Temperature Controller Replacement Replacing your Athena or Cal 00 temperature controller. Also, upgrading from Athena to Cal 00 Section.0 CONTENTS.0 Athena & Cal 00 replacement Cal 00 upgrade...- BEFORE YOU START: Read instructions thoroughly before beginning. ELECTRICAL WARNING: POWER DOWN DRS AND DISCONNECT FROM POWER SOURCE. CHECKLIST: The following items will be needed in this section. Athena temperature controller part no Cal 00 temperature controller part no For Upgrading only: Phillips screwdriver Small straight blade screwdriver Metric & American Allen wrenches Metal file For technical problems, please contact the Air-Vac technical service department at: Air-Vac Engineering Company, Inc. 0 Progress Avenue Seymour, CT 0 Phone: Fax: solder.tech@air-vac-eng.com 0//0
2 DRS Technical Service Manual.0 Athena & Cal 00 Replacement! IMPORTANT VERIFY DRS IS DISCONNECTED FROM THE POWER SOURCE. The temperature controllers are located in the DRS right box (A), (fig.). STEPS: Remove the 0/ button head screw (B), (fig.), and swing right box open. B A Fig. The remaining steps will be performed assuming you are located behind the DRS. Determine if you have Athena controllers (C), (fig.), or Cal 00 controllers (D). Fig. C Athena D Cal 00
3 DRS Technical Service Manual! IMPORTANT Each type of controller has a removable bezel and circuit board assembly (E), (fig.). The controller sleeve (F) stays in the machine during controller removal. ELECTROSTATIC PRECAUTIONS SHOULD BE OBSERVED WHEN HANDLING THE CONTROLLER OUTSIDE OF THE SLEEVE. Grasp left and right side controller face grips (G), (fig.), and firmly squeeze in and slide controller out of the sleeve. TIP: While pulling out the controller, a gentle, side to side rocking motion will make removal easier. F Fig. E G Remove your new controller from its anti-static packaging and carefully install into the sleeve. It should snap in when fully seated. Place old controller into anti-static packaging. Please refer to the instructions included with your new temperature controller for programming details.
4 DRS Technical Service Manual.0 Cal 00 Upgrade! IMPORTANT VERIFY DRS IS DISCONNECTED FROM THE POWER SOURCE. The temperature controllers are located in the DRS right box (A), (fig.). STEPS: Remove the 0/ button head screw (B), (fig.), and swing left box open. B A Fig. The remaining steps will be performed assuming you are located behind the DRS. Remove the four 0- low head screws (C), (fig.), with a / Allen wrench. Carefully lift the sub plate assembly (D) out of the right box and rest on top of power panel. Squeeze the hinge pins (E) together to release the left box and then lower box to bench. Remove lid support pin (F) to allow box to sit flat on bench. With the left box cover sitting on the bench next to the machine, flip the entire sub-plate assembly (D) back over and rest on top of cover (fig., page ). C Fig. E D F
5 DRS Technical Service Manual Remove the four M screws (G), (fig.), with a mm Allen wrench and then remove the wire ties holding the harness. Carefully lift the riser plate assembly (H) off of the sub plate assembly and flip over for access to the Athena controller rear wire connections. You can re-install two M screws (G) into the sub plate to hold the riser plate upside down in place. Remove and replace one controller at a time so you do not get the wire connections mixed up. G Fig. H Cover Remove the wires from the Athena controller (figure ) with a phillips head screwdriver. The wire colors on terminals, & may be different than indicated in figure (make a note if they are different). Red POS - Red Yellow Fig. NEG - 0 } Thermocouple Light Blue
6 DRS Technical Service Manual Gently slide a thin straight blade screwdriver behind the locking tabs of the Athena retaining ring (I), (fig.), pry up and slide the ring down several clicks. Repeat, alternating sides, until the retaining ring slides off. Remove Athena (J) from cutout. Insert the new Cal 00 controller into the same cutout, making sure that the face is orientated properly (fig.). You made need to use a file to make the cutout larger. Slip the retaining ring (I) back over the Cal 00 sleeve and lock against the riser plate (K). Fig. I K J Fig.
7 DRS Technical Service Manual For wire connection steps 0-, refer to figure on page. If the wire lengths are too short, it may be necessary to splice on additional wire lengths by soldering and adding heat shrink tubing over the splice. Remove spade lugsfrom the end of wires and strip insulation back approximately /. 0 Connect white/red wire (Athena terminal ) to Cal 00 terminal. Connect white/black wire (Athena terminal ) to Cal 00 terminal. Connect yellow wire (Athena terminal ) to Cal 00 terminal. Connect red wire (Athena terminal 0) to Cal 00 terminal. Connee thick black wire (Athena terminal ) to Cal 00 terminal. Connect thick light blue wire (Athena terminal ) to Cal 00 terminal. Connect red wire (Athena terminal ) to Cal 00 terminal 0. Connect black wire (Athena terminal ) to Cal 00 terminal. Repeat steps 0- for the remaining Athena controller(s) to be upgraded. See complete diagram for all wire colors and numbers (fig., page ). If you have a single diffuser with only two controllers, make sure the wires for the center (left diffuser) Athena are secured and the ends are shrink wrapped to prevent grounding or shorting.
8 DRS Technical Service Manual Fig. - Athena & Cal 00 Temperature Controller Hookup (rear view) Athena # Athena # Red Red POS - 0 Yel. POS - Yel. NEG - 0 } NEG - 0 } Athena # Red & 0 & Thick Light Blue POS - Yel. NEG - 0 } 0 & & Cal 00 # Cal 00 # Cal 00 # Blk Red Yel Blk Red Yel Blk Red Yel Wht/Red Yel Red Wht/Blk Thick Thick Blk Lt.Blue Wht/Red Yel Red Wht/Blk Thick Thick Blk Lt.Blue Wht/Red Yel Red Wht/Blk Thick Thick Blk Lt.Blue { 0 { 0 {
9 DRS Technical Service Manual 0 After all wire connections have been made, reverse steps -, earlier in this section, to reinstall the riser plate and sub plate assemblies back into the DRS right box. Reconnect power to the DRS and power up module. At DRS software, DO NO LOG ON. Verify that your new Cal 00 controllers have power (the front display should be green) and program them according to the instructions in section...! IMPORTANT PROGRAMMING IS VERY IMPORTANT. IF THE CONTROLLERS ARE NOT PRO- GRAMMED, THE DRS AND ITS SOFTWARE WILL NOT WORK. Once the controllers are programmed, log into the DRS software with a High level operator password and then right mouse click the spinning chip in the bottom right corner to access the hidden menu. Under Options/Open, run the Heater Burn in Profile (figure ) to make sure the controllers reach their setpoint temperature and appear to be stable. If you get a Temp Communication Link error message, you will need to check the controller programming first. If that appears okay, you then need to check your communication wires on the Cal 00 terminals, 0 and to make sure they are wired correctly. (Usually terminals #0 & # (red & black) are reversed). If your controller has difficulty reaching or stabilizing its setpoint, you will need to again check the controller programming. Fig.
Section 5 BATTERY REPLACEMENT
u Section 5 BATTERY REPLACEMENT j i 5.1 General The internal battery is used for preserving the clock and programming memory in the models 5000 and 7000. I i The procedure for each is given separately.
More informationFLEX-6300 Handle Installation Guide
FLEX-6300 Handle Installation Guide May 6, 2014 Thank you for purchasing the FLEX-6300 Handle Kit. The following guide will provide the necessary stepby-step procedure for installing the FLEX-6300 Handle
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationHarmony Remote Repair
Harmony Remote Repair harmonyremoterepair.com How to install your new Harmony One Front Cover/Touch Screen Important! Before you begin working on your Harmony One, you must discharge any static electricity
More informationRepairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip
Repairing Microsoft Wedge Touch Mouse Battery Cover Retaining Clip Disassembly, repair and reassembly of Wedge Touch mouse when the battery cover will not stay closed. Also is a good guide to repair other
More informationRemoving and Replacing the Y-truck
Service Documentation Removing and Replacing the Y-truck To remove and replace the Y-truck you will need the following tools: 4mm Allen wrench 12mm stamped flat wrench #2 Phillips screwdriver (magnetic
More informationLF Series Assembly Instructions
LF Series Assembly Instructions 1998760 Revision A-10 Complete Series Master Packet 2010 Kimball International, Inc. T 800.482.1818 F 812.482.8300 Footprint Storage and Metal Filing Systems Assembly Instructions
More informationGEN II Toyota Prius Back Door Opener Switch Replacement & License Plate Lights
GEN II Toyota Prius Back Door Opener Switch Replacement & License Plate Lights Rubber Surface of Switch had Degraded to Tar-like Substance Vehicle Manufacture Date 10/06 OLD SWITCH IN GARNISH SWITCH REMOVED
More informationMac mini Model A1283 RAM Replacement
Mac mini Model A1283 RAM Replacement Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION Accessing the RAM requires the removal of the internal frame. TOOLS: Jimmy (1)
More informationKN-8828B Upgrade Directions
KN-8828B Upgrade Directions This document outlines the steps to take to update earlier Hottop Bean Roasters to the KN-8828B 2007 by Chang Yue and Hottop USA - All Rights Reserved No part of this document
More informationMaintenance Information
47104302 Edition 1 November 2012 Cordless Drill/Driver QX Series Maintenance Information Save These Instructions Tool Diagnosis 1. Before servicing this unit, you will need a fully charged battery of known
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Swing s 73 74 NOTES INSTALLATION OF A GDM-SWING DOOR Phillips Head Screwdriver (2) - 1/8" Drift Punches (forged) Top Bracket NOTE: It may be necessary
More information101B, 210X, ELM, VSTB Installation Manual
101B, 210X, ELM, VSTB Installation Manual 99-16105-I001 Copyright 2010 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in examples
More informationRef Qty Part Description Part Number 1 1 Headlight-LED Nylon Tie Strap Instructions
LED LIGHTS KIT P/N 2880289; 2880621 APPLICATION MY15-16 INDIAN MOTORCYCLES WITH THUNDERSTROKE 111 BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationRazr Adapter Retrofit Project by Craig Hoy, Edmonton, AB, Canada
Razr Adapter Retrofit Project by Craig Hoy, Edmonton, AB, Canada The following is a description of the process that I have used to modify the console eject box for e38, e39, e46 and x5 s, part number 84-21-6-933-415.
More informationDO NOT PULL ON THE SHEATH.
Removing and Replacing the Head Cover To remove and replace the head cover you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) Removing the Head Cover 1. Ready the machine
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More informationHP Envy TouchSmart 15 Fan Replacement
HP Envy TouchSmart 15 Fan Replacement Replacing the fan in the HP Envy TouchSmart. Written By: Ramon Villadonga ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION You might need to replace the
More informationMac mini Model A1283 Speaker Replacement
Mac mini Model A1283 Speaker Replacement Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION Restore sound to your mini by replacing the speaker. TOOLS: Jimmy (1) Phillips
More informationWritten By: Arthur Shi
Remove and replace a broken or malfunctioning motherboard for the Google Pixel XL. Written By: Arthur Shi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 21 INTRODUCTION If you're having issues with the overall
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2006 2007 Honda Ridgeline THE safety accessory of the 21 st Century. P/N 210 0142 0 Rev. A (9/5/07), BTV 2007 Muth Company, LLC Professional Installation Recommended:
More informationipad 2 GSM Home Button Assembly Replacement
ipad 2 GSM Home Button Assembly Replacement This guide will show you how to replace the home button assembly in your ipad 2. Written By: Scott Head ifixit CC BY-NC-SA www.ifixit.com Page 1 of 29 INTRODUCTION
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationWritten By: Walter Galan
ipad 2 CDMA Camera Bracket Replacement Replace the camera bracket in your ipad 2 CDMA. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 29 INTRODUCTION Use this guide to replace the
More informationipad 2 GSM Right Cellular Data Antenna Replacement
ipad 2 GSM Right Cellular Data Antenna Replacement Replace the right cellular data antenna in your ipad 2 GSM. Written By: Brett Hartt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 43 INTRODUCTION Use this
More informationMac mini Model A1283 Internal Frame
Mac mini Model A1283 Internal Frame Replacement Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9 INTRODUCTION Remove your internal frame to access most of your mini's internals. TOOLS:
More informationThe wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist:
WICK REPLACEMENT The wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist: Slow to light, hard movement of the wick adjuster knob, kerosene odor
More informationReplacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)
Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the
More informationDisassembling HP Envy TouchSmart 15 Heat
Disassembling HP Envy TouchSmart 15 Heat Sink Removal of the Heat Sink Written By: Ramon Villadonga ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION You may need to replace or re-seat your heatsink
More informationipad 2 Wi-Fi EMC 2415 Front Panel Replacement
ipad 2 Wi-Fi EMC 2415 Front Panel Replacement Replace the Front Panel in your ipad 2 Wi-FI EMC 2415. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 31 INTRODUCTION Note: this is a
More informationMac mini Model A1176 SSD Installation
Mac mini Model A1176 SSD Installation Installing an SSD in the Mac Mini A1176 Written By: Dozuki System 2017 guides.crucial.com Page 1 of 13 INTRODUCTION Upgrade your hard drive for more storage capacity.
More informationPRINTER REPAIR ARTICLE HP LJ 4345/M4345 Swing Plate Replacement
a1 output bin a2 DUPLEXER a4 FORMATTER COVER a5 FORMATTER a3 fuser entr. guide PRINTER REPAIR ARTICLE HP LJ 4345/M4345 Swing Plate Replacement Grinding noise near the fuser means it is time to replace
More informationMODULAR BUMPER INSTALLATION MANUAL
MODULAR BUMPER INSTALLATION MANUAL Parts List* 1 Center section 1 Side extension, passenger / right 1 Side extension, driver / left 1 Side cap, passenger / right 1 Side cap, driver / left 1 Brush guard,
More informationPERSONAL RECORD KEEPING
PRO3700 2 P R O 3 7 0 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for
More informationMacBook Pro 15" Unibody 2.53 GHz Mid 2009 Front Display Glass Replacement
MacBook Pro 15" Unibody 2.53 GHz Mid 2009 Front Display Glass Replacement Replacing the front display glass. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION Use
More informationMechanical Frappe Press
Mechanical Frappe Press Operation Manual CONTENTS OPERATIONAL INSTRUCTIONS PRECAUTIONS PART NAMES INCLUDED ITEMS BASIC OPERATION MAINTENANCE REPLACEMENT PARTS Thank you for using The Frapptastic Five Mechanical
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationInstructions to fit Emulator in place of floppy drive M.D.R.
Instructions to fit Emulator in place of floppy drive M.D.R. Before starting, read through all the following instructions, and then when you do begin, read each number section before attempting that particular
More informationWritten By: Evan Noronha
Replace the logic board in an ipad Air LTE. Written By: Evan Noronha ifixit CC BY-NC-SA www.ifixit.com Page 1 of 50 INTRODUCTION Follow the steps in this guide to replace the logic board in an ipad Air
More informationWritten By: Walter Galan
Replace the logic board in your ipad 3 Wi-Fi. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 29 INTRODUCTION Use this guide to replace the logic board. TOOLS: iopener (1) Phillips
More informationInstallation Instructions
Installation Instructions 30 Built-In Wall Oven with Microwave JTP86, JT965 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before You Begin Read these instructions carefully
More informationZ-Truck Up-and-Down Motion. Y-Truck Side-to-Side Motion. Head. Squaring Plate. Sliding Plate FIGURE 1: THE CARVEWRIGHT MACHINE
Setup and use of CarveWright CO2 Powered Dragster Jig The CO 2 powered Dragster Jig will arrive from the factory fully assembled, calibrated, and squared. In order to get the best results, your CarveWright
More informationWritten By: Brett Hartt
Replacing the Wi-Fi antenna in the third generation ipad Written By: Brett Hartt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 31 INTRODUCTION Wireless internet is awesome. A third generation ipad without
More informationVolvo 240/260 New Face Overlay Installation Models By Dave Barton
Volvo 240/260 New Face Overlay Installation 1975-80 Models By Dave Barton These custom faces are the product of years of research and experimentation. They are printed with a special printer using waterproof
More informationipad 3 4G Home Button Control Board Replacement
ipad 3 4G Home Button Control Board Replacement Replace the home button control board in your ipad 3. Written By: Brett Hartt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 28 INTRODUCTION This guide will
More informationPioneer Elite Smart Speaker F4 Button Panel Circuit Board Replacement
Pioneer Elite Smart Speaker F4 Button Panel Circuit Board Replacement Use this guide if the buttons or microphone on your speaker do not work. Please note that replacing this part requires the speaker's
More information16 STEEL CABINET HEAVY DUTY
HEAVY DUTY 16 STEEL CABINET ASSEMBLY INSTRUCTIONS SIX DRAWER BASE CABINET 12-2013 Parts List Part No Description Qty Image SIX DRAWER BASE CABINET Part No Description Qty Image SB-1 Cabinet Body 1 SLD-01
More informationWritten By: Brett Hartt
Replace the battery in your ipad 3 4G. Written By: Brett Hartt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 36 INTRODUCTION When your ipad can't stay awake for longer than a few hours, it is time to replace
More informationMacBook Pro 15" Unibody Mid 2009 Front Display Glass Replacement
MacBook Pro 15" Unibody Mid 2009 Front Display Glass Replacement Replacing the front display glass. Escrito por: Andrew Bookholt ifixit CC BY-NC-SA es.ifixit.com Página 1 de 24 INTRODUCCIÓN Use this guide
More informationFinish Line Emergency Brake Boot INSTRUCTION SHEET. Part Number. Application: Corvette. Part Includes.
Application: 1997-2004 Corvette Part Includes 1 - Emergency Brake Boot Finish Line Emergency Brake Boot Tools Needed T15 10mm PRE-INSTALLATION NOTES Read completely through instructions to familiarize
More informationMac mini (PowerPC) Lower Case Replacement. Written By: irobot. ifixit CC BY-NC-SA Page 1 of 10
Mac mini (PowerPC) Lower Case Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION The bottom case of the Mac mini. TOOLS: Jimmy (1) Anti-Static Wrist Strap (1) Phillips
More informationunit 3: GENErAL ElectriCAL SySTEM DiAGNOSiS
Electrical/Electronic Systems unit 3: GENErAL ElectriCAL SySTEM DiAGNOSiS lesson 4: wire and connector repairs I. Connector repairs A. Connector repairs involve fixing damaged wires. Wires are marred due
More informationWritten By: Walter Galan
Replace the Logic Board in your ipad 4 Wi-Fi. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 32 INTRODUCTION Use this guide to replace the logic board. TOOLS: iopener (1) Phillips
More informationExterior Door Handle - LH - Unpainted (05-14 All)
Tools Required: Exterior Door Handle - LH - Unpainted (05-14 All) 1) 10mm and 7mm sockets 2) Socket wrench (small size recommended) 3) T30 Torx bit 4) Plastic pry/molding tool (below, A) 5) Thin plastic
More informationINSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)
INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied
More informationFig. 1 Fig. 2. Fig. 3 Fig. 4 TOOLS REQUIRED: *Phillips Screwdriver *Three Inch Putty Knife*Panel Removal Tool *10mm Nut Driver CONTENTS:
*Phillips Screwdriver *Three Inch Putty Knife*Panel Removal Tool *10mm Nut Driver CONTENTS: 2EA. 6X9 TWO WAY SPEAKERS P/N 05030281AA 1EA. INSTRUCTIONS P/N RBI05LXREAR 300c and Charger 1. Remove the lower
More informationSignal Mirror Installation Instructions Dodge Charger, Dodge Magnum, Chrysler 300
Signal Mirror Installation Instructions 2006-2009 Dodge Charger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300 THE safety accessory of the 21st Century. P/N 210-0123-0 Rev. A4 (10/7/09), BTV 2007 Muth
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Pontiac Grand Prix 1997-2003; Sedan and oupe THE safety accessory of the 21st entury. P/N 210-0018-0 Rev 2 (6-24-04), GG 2002 Muth Mirror Systems, LL. Note: Professional
More informationcompile system INSTALLATION GUIDE Updated January 2019
INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness
More informationSignal Mirror Installation Instructions Toyota Tacoma
Signal Mirror Installation Instructions 2005-2015 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0115-0 Rev. A4 (3/11/15), BTV 2005 Muth Mirror Systems, LLC Page 3 of 12PplPage 3 of 12
More informationDaytime Running Lights - Splice-in (10-12 All):
Time Necessary: Approximately 1 hour Tools Required: Heat Gun Installation Procedure: Daytime Running Lights - Splice-in (10-12 All): 1. It is recommended that the positive terminal be removed from the
More informationPowerbook G3 Lombard (1999) USB Repair Manual
Powerbook G3 Lombard (1999) USB Repair Manual Copyright 2003 Powerbookmedic.com. All rights reserved. Any portion of this manual may not be copied, reproduced, or distributed without the express written
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: REAR SPOILER KIT - CARBON FIBER INFINITI Q60 T99J1 5CH0B KIT CONTENTS: Item Qty. Part Description A 1 Spoiler Assembly B 4
More informationMM Strut Tower Brace, Cobra (MMSTB-7)
The MM strut Tower Brace attaches to each strut tower and to the firewall. 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM
More informationTHE TOOLS RECOMMENDED Phillips Screwdriver Stripper/Crimper Electrician Pliers ½ open end wrench or ratchet wrench with ½ deep socket Utility knife
16 X 20 HEATER ELEMENT WIRE CONNECTION REPAIR DK20/A/S/SP The following instructions are on the repair of a potentially faulty wire connection in your 16 x 20 heat platen. It is recommended that only those
More information2015 GMC Yukon. Upper Class Grille Insert
Upper Class Grille Insert TOOLS REQUIRED: Flat Head Screwdriver Long Flat Head Screwdriver Phillips Screwdriver 7mm Socket 10mm Socket Ratchet & Extensions 3/16 Drill Bit Power Drill Cutting Wheel or Saw
More informationWritten By: Walter Galan
ipad 3 Wi-Fi Dock Connector Replacement Replace the dock connector in your ipad 3 Wi-Fi. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 29 INTRODUCTION Use this guide to replace the
More informationArc Trainer Main Frame Assembly
Arc Trainer Main Frame Assembly Kit No. 610AK019-4 Kit No. 630AK019-4 NOTE: This instruction sheet describes how to replace the main frame assembly in the Arc Trainer 610A. Tools Required 3/16 Allen wrench
More informationAsus Zen AiO Pro Z240IC Ethernet/LAN Port Replacement
Asus Zen AiO Pro Z240IC Ethernet/LAN Port Replacement How to replace the Ethernet/LAN board and port on the Asus Zen AiO Pro Z240IC. Written By: Sahil Sharma ifixit CC BY-NC-SA www.ifixit.com Page 1 of
More informationMac mini Model A1283 PRAM Battery Replacement
Mac mini Model A1283 PRAM Battery Replacement Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION The time and date, as well as other settings, are kept by the PRAM battery
More informationDIY S2000 Door Card Removal
DIY S2000 Door Card Removal This Do-It-Yourself guide is intended to guide you through removing the door cards from your S2000. Tools Required: Phillips Head Screwdriver Trim tools (pry tool and a trim
More informationAssembly Procedures for 96-Position GPEC II and III Sealed Connector System (Harness)
Assembly Procedures for 96-Position GPEC II and III Sealed Connector System (Harness) Instruction Sheet 408-10229 08 SEP 17 Rev E Wire Dress Assembly (Straight Version) Plug Housing Assembly Optional Blink
More informationExponents Bench Cushion
Exponents Bench Cushion Power Drill #2 Phillips Bit Bit Holder Page 1 of 2 939500640 Rev A 1. Place cushion on top of the bench, so the black Coalesse tag is in the right rear corner of the bench. 2. From
More informationHTC Evo 4G Motherboard Replacement
HTC Evo 4G Motherboard Replacement Motherboard replacement. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Restore life to your HTC Evo 4G by replacing the motherboard.
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationLAN Locker Adjustable Shelves
Adjustable Shelves LAN LOCKER ADJUSTABLE SHELVES * Adjustable Shelves are available for LAN LOCKER widths: 24, 30, 48, 60, and 72. * When installing more than one Adjustable Shelf, it is recommended that
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationMac mini (PowerPC) Hard Drive Replacement
Mac mini (PowerPC) Hard Drive Replacement Written By: irobot INTRODUCTION Upgrade your storage with a new hard drive. TOOLS: 1.5" Thin Putty Knife (1) Phillips #00 Screwdriver (1) Phillips #1 Screwdriver
More informationP/N B ProBlue and DuraBlue Thermostat Service Kit - P/N
P/N 1029717B ProBlue and DuraBlue Thermostat Service Kit - P/N 1028321 This instruction sheet provides separate instructions for replacing a thermostat on ProBlue and a DuraBlue adhesive melters. Tools:
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More informationCustom Grille Insert
1 of 8 Thank you for your purchase of DBCustomz 2016+ Toyota Tacoma! This product was carefully crafted to ensure a perfect fit with your vehicle. The instructions below are provided to allow for an easier
More informationPERSONAL RECORD KEEPING
2 P R O 3 7 0 A s s e m b l y i n s t r u c t i o n s PERSONAL RECORD KEEPING Tip: Record the serial numbers of your Octane Fitness elliptical in the spaces below. This will make it easier for you to obtain
More informationInstallation Instructions for Converting Hinging on Roll-In Refrigerators
Installation Instructions for Converting Hinging on Roll-In Refrigerators Part number 161651 hinge conversion kit RH is for converting a right side hinged door and part number 161652 hinge conversion kit
More informationJeep Wrangler JK & 4-Door Front Pair Part # Revision H
Jeep Wrangler JK 2007 2 & 4-Door Front Pair Part # 10045 Revision H 03-25-09 Step 1: Prior to Installation: A) Bushwacker only approves installing the flares according to these written instructions with
More informationYOUR LIFE. YOUR FIRE. Ortal Curved & Islands Fireplaces User s Manual
YOUR LIFE. YOUR FIRE. Ortal Curved & Islands Fireplaces User s Manual [USA Fireplace Models [THIS ISTALLATION MANUAL INCLUDES ASSEMBLY INSTRUCTIONS FOR THESE MODELS: STAND ALONE 7565 CURVED TUNNEL DOUBLE
More informationQB78 CO 2 Pellet Rifle
QB78 CO 2 Pellet Rifle Maintenance Instructions Text and photos by George Fox Lang The Chinese QB78 pellet rifle is one of the nicest and most popular CO 2 rifles ever produced. Here are the long-wanted
More informationThe Bowflex Revolution XP Home Gym Assembly Instructions. P/N: Rev ( /0 )
P/N: 001-7057 Rev ( /0 ) The Bowflex Revolution XP Home Gym Assembly Instructions 2 Table of Contents Before You Start... 2 Tools You Will Need / Hardware Contents... 3 Box Contents... 6 Assembling Your
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2005-2010 Chevy Corvette C6 THE safety accessory of the 21 st Century. P/N 210-0144-0 Rev. A3 (9/29/2011), BTV 2007 Muth Mirror Systems, LLC Page 3 of 10PplPage
More informationipad 3 4G Home Button Assembly Replacement
ipad 3 4G Home Button Assembly Replacement Replace the home button assembly in your ipad 3 4G. Written By: Brett Hartt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 29 INTRODUCTION Use this guide to replace
More informationKX2 Side KX installation
KX2 Side KX installation NOTE: The installation of any Side KX parts does NOT require the unsoldering of any connection nor removal of ANY of the boards from within the radio! The user/installer assumes
More informationEASY-IN POOL STEP SYSTEM NE132
EASY-IN POOL STEP SYSTEM NE132 This instruction manual features multiple guides for the step unit components. 7939 EASY POOL STEP (NE113) FOR USE WITH: EASY-IN POOL STEP (NE126) 6492 PARTS & HARDWARE FOR
More informationSLEEVE AND PITCH INSTRUCTION BOOKLET
SLEEVE AND PITCH INSTRUCTION BOOKLET Contents Section I: Replacing White, Green or Black Sleeves with Low Wear 12cm Green Sleeves Refer to this section if your oars currently have original white, green
More informationWritten By: Andrew Optimus Goldberg
Replace the screen your GSM/AT&T iphone 4. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 25 INTRODUCTION [video: http://www.youtube.com/watch?v=obpfpfx5abw] Use this guide
More informationDOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6. Verify accessory fitment at Polaris.com.
DOOR KIT P/N 2882528 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationInstallation Instructions
Installation Instructions Self-Cleaning Radiant Electric Slide-In Range JSP42, JS968, JS900, JS905, JSP46 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before You Begin Read
More informationChrome Mustang Billet Interior Door Handles (05-09) - Installation Instructions
Chrome Mustang Billet Interior Door Handles (05-09) - Installation Instructions The below installation instructions work for the following products: Chrome Mustang Billet Interior Door Handles (05-09)
More informationMM Strut Tower Brace, GT (MMSTB-5.1)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Strut Tower Brace, 1996-97 GT (MMSTB-5.1) MMSTB-5.1 is for 1996-97 GT s with
More informationSignal Mirror Installation Instructions Honda Odyssey
Signal Mirror Installation Instructions 2005-2009 Honda Odyssey THE safety accessory of the 21st Century. P/N 210-0122-0 Rev. A4 (6/9/09), BTV 2006 Muth Company, LLC PROFESSIONAL INSTALLATION RECOMMENDED
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #
INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD
More informationYOUR LIFE. YOUR FIRE. Ortal Curved & Islands Fireplaces Installation Manual. Ortal USA - Version: 1.3 November, 2017 SKU: KPMANCIRISLUS17B
YOUR LIFE. YOUR FIRE. Ortal Curved & Islands Fireplaces Installation Manual Ortal USA - Version: 1.3 November, 2017 SKU: KPMANCIRISLUS17B [THIS ISTALLATION MANUAL INCLUDES ASSEMBLY INSTRUCTIONS FOR THESE
More information