Introduction. Splinting made simple. Multicast perforation patterns. Ease of finishing: Processing temperature: Memory: Transparency:

Transcription

1 splinting products

2 Introduction Multicast Thermoplastics offer OT and O&P practitioners the best form of dynamic splinting available today. Perfect for fracture immobilisation, static splinting, dynamic splinting, splinting for burn patients, foot orthotics and post-operative splinting. Moulds directly to the skin X-ray translucent After application, it transforms into a hard splint that does not need reinforcing Indefinite shelf life: no waste Follows the exact contours of the treated surface Does not stick to body hair Lightweight splinting Inexpensive - great prices available Multicast thermoplastics also do not emit toxic gases or vapours during application. Splinting made simple Memory: All Multicast products have 100% plastic memory. That means the material will recover its original, form and thickness after reheating. Splints can be remolded as frequently as needed! variety of handling techniques. Multicast Rigid has minimal stretch resistance. This property is used for the ease of circumferential splinting. Ease of finishing: Multicast generally has exceptional smoothing capabilities when heated. The unique coatings of Multicast Standard make fingerprints and other surface marks disappear. Multicast Ortho resists fingerprints too while the material is warm. Major modifications can be made with a heat gun. It can also be mechanically grinded or buffed for quick finishing (at a moderate speed). Modifications should only be carried out when the material has completely cooled down. Cutting: Can be cut with scissors or knife. Bonding: Self adhesive when hot - just press together. Fastening: Hook & loop, rivets, etc. No solvents needed! Processing temperature: Uncoated materials like Multicast Ortho and Multicast Rigid can be processed at the temperature of 60 C - 65 C (140 F F). Multicast Standard has a processing temperature of 70 C - 75 C (158 F F). All Multicast materials are designed to be moulded directly on the patient s skin. While processed in hot water the material absorbs heat, but when taken out of the water surface temperature decreases automatically. See below: Transparency: Multicast Ortho and Multicast Standard turn semi-transparent when heated. This enables the therapist to see contours and landmarks under the material. Multicast Rigid is a coloured material that become opaque when heated. Drape or conformability: All Multicast materials are superior in following the exact contours of the treated surface, even to minute details, due to their exceptional anatomo-topographic properties. Stretch: Multicast Standard and Multicast Ortho have moderate stretch resistance which allows control over the material and offers a Multicast perforation patterns All Multicast thermoplastic sheets are available in solid form (i.e. non-perforated) and with varying degrees of perforations: micro (42%), multi (38%) and mini (2.5%). Non-Perforation Micro (42%) Multi (38%) Mini (2.5%) 2 further information:

3 Multicast range The patented velvet like surface of Multicast Standard provides perfect conformity and comfort. Ease-of-use and exceptional ventilation properties have made Multicast Standard a favourite among medical professionals. Multicast Standard will also not stick to itself in hot water. Multicast ortho Multicast Ortho is an exceptionally versatile thermoplastic that offers the advantages of partial transparency when heated. Multicast Ortho offers maximum drape and has a lower heating temperature than Multicast Standard. Multicast Rigid follows the exact contours of the treated surface. After processing, it transforms into a hard splint. It does not need reinforcing, its light-weight and does not shrink when heated. Ideal for applications where the splint needs to be firm and enduring. Material selection: Multicast Standard can be substituted by Multicast Ortho depending on processing and splint preference, e.g. Multicast Ortho is transparent when heated. Points to consider: Multicast Standard is preferable for an orthosis with a small surface area. Multicast Standard is preferable for children. Multicast Standard is preferable when applied over a bandage. The material will not stick to bandages. Highly recommended for post-operative splinting and burn injuries. Multicast Rigid is preferable for an orthosis with a large surface area. Choose a thermoplastic with large ventilation holes, such as Micro and Multi to prevent skin maceration. If you have limited experience with splinting techniques choose Mini perforated sheets instead of Multi. Non-perforated plates are only used for non-circular orthoses that cover less then half of the body surface. Absence of ventilation holes will lead to skin maceration. Choose Multicast Standard or Multicast Ortho when using Gravity-Assisted Moulding techniques. For vertical moulding choose thermoplastics with good adhering surface, such as Multicast Ortho or Multicast Rigid. Kids Teens Adults Body Part finger 0.8mm micro 0.8mm micro 1.6mm micro wrist 1.6-2mm micro 2-2.5mm micro/mini mm mini elbow 2mm micro 3mm mini 3.2mm non perf/mini shoulder 2mm micro 2.5mm mini/multi 3mm non perf/mini body 3mm multi 3mm multi 4mm mini lower leg 2mm micro 3.2mm non perf/mini 3.2mm non perf/mini our full range: 3

4 Standard Multicast Standard is a low temperature thermoplastic material bonded with a 0.6mm furry foam layer. The characteristic advantage of the foam coating is that the thermoplastic does not stick to itself in hot water, thus sizable surfaces can be put in a small hot water container and the material is easier to work with. The foam coating also creates a minute layer of air between the patient's skin and the thermoplastic, reducing the possibility of skin chafing. Due to Multicast Standard s exceptional anatomical properties, when heated the material follows the exact contours of the treated surface - non perforated TC mm 60 x 42cm TC2000 2mm 60 x 44cm TC mm 60 x 45cm TC mm 60 x 90cm TC4000 3mm 60 x 45cm TC4001 3mm 60 x 90cm TC5000 4mm 60 x 45cm TC5001 4mm 60 x 90cm - micro TC mm 60 x 41cm Processing: The material can be heated in the following ways: TC mm 60 x 42cm TC2100 2mm 60 x 44cm Water (from 70 C) Steam (from 90 C) Dry heat (max 150 C) Heat gun Heating plate The material can be moulded after 2 minutes of heating at 70 C or 1 minute heating at 75 C. - multi TC2300 2mm 60 x 44cm TC mm 60 x 45cm TC mm 60 x 90cm TC4300 3mm 60 x 45cm TC4301 3mm 60 x 90cm Product availability: Multicast sheets are generally available in Beige, but other colours may available on request (bulks orders only) - mini TC2200 2mm 60 x 44cm TC mm 60 x 45cm TC mm 60 x 90cm TC4200 3mm 60 x 45cm TC4201 3mm 60 x 90cm TC5200 4mm 60 x 45cm TC5201 4mm 60 x 90cm Moulding characteristics: Transparency Memory Drape Stretch Bonding Processing Temperature Moderate 100% Maximum Moderate Moderate C 4 further information:

5 Ortho Multicast Ortho is a low-temperature thermoplastic with enhanced processing characteristics such as transparency and maximum drape. Multicast Ortho is an exceptionally versatile thermoplastic material that offers the advantages of transparency when heated. Multicast ortho - non perforated TD mm 60 x 43cm TD2000 2mm 60 x 44cm TD mm 60 x 45cm TD mm 60 x 45cm Characteristics of Multicast Ortho: TD mm 60 x 90cm TD5000 4mm 60 x 45cm Turns clear when heated - then opaque when cooled Maximum drape Possibility of vertical (anti-gravity) positioning Bonds without need for solvents Resists fingerprints and other pressure marks Lower processing temperature than Multicast Standard TD5001 4mm 60 x 90cm Multicast ortho - micro TD mm 60 x 43cm TD2100 2mm 60 x 44cm Multicast ortho - multi TD mm 60 x 43cm Processing: The material can be heated using the same methods as Multicast Standard. The material can be moulded after a 2 minutes of heating at 60 C or 1 minute heating at 65 C. Product availability: Multicast sheets are generally available in Beige, but other colours may available on request (bulks orders only) TD2300 2mm 60 x 44cm TD mm 60 x 45cm TD mm 60 x 45cm TD mm 60 x 90cm Multicast ortho - mini TD mm 60 x 43cm TD2200 2mm 60 x 44cm TD mm 60 x 45cm TD mm 60 x 45cm TD mm 60 x 90cm TD5200 4mm 60 x 45cm TD5201 4mm 60 x 90cm Moulding characteristics: Transparency Memory Drape Stretch Bonding Processing Temperature Maximum 100% Moderate Maximum Maximum C our full range: 5

6 Rigid Multicast Rigid is a strong low-temperature thermoplastic material that follows the exact contours of the treated surface. After processing it transforms into a hard splint. It does not need reinforcing, it is rigid, light-weight and does not shrink. - non perforated TE2050 2mm 60 x 44cm TE mm 60 x 45cm TE mm 60 x 90cm Due to its heavy plastic memory, the material can be reheated and remoulded. Characteristics of Multicast Rigid: - micro TE2150 2mm 60 x 44cm Extra rigidity Extra strength Possibility of vertical (anti-gravity) positioning Recommended for orthosis with large surface - multi TE2350 2mm 60 x 44cm TE mm 60 x 45cm TE mm 60 x 90cm Processing: The material can be heated using the same methods as Multicast Standard. The material can be moulded after a 2 minutes of heating at 60 C or 1 minute heating at 65 C. - mini TE2250 2mm 60 x 44cm TE mm 60 x 45cm TE mm 60 x 90cm Product availability: Multicast sheets are generally available in Beige, but other colours may available on request (bulks orders only) Moulding characteristics: Transparency Memory Drape Stretch Bonding Processing Temperature Minimum 100% Maximum Maximum Maximum C 6 further information:

7 Pre-cuts Wrist Immobiliser 1, micro perf, beige Rest Splint 1, mini perf, beige Thumb Splint 1, micro perf, beige Multicast Precuts are cut to and ready to be applied to the body, saving you time and money.available in a variety of s and styles, Pre-cuts reduce fabrication costs with no need for tracing, designing and cutting. Volar Splint II 1, mini perf, beige Upper Arm Brace 2 s, mini & non perf, beige PIP Extension Dig III 1, micro perf, beige Volar Splint I 1, mini & micro perf, 4 colours Lower Leg Brace 1, mini & non perf, beige Dropfoot Splint 1, mini perf, beige our full range: 7

8 Sundries Hook and Loop Hook and loop from Algeos is available in several s, colours and constructions. Listed here is only small selection of our entire fastenings range. To view our full range please contact us for our full catalogue - see bottom of page for further details. Hook & loop - standard sold per metre /type white beige 25mm - hook LA3710 LA mm - loop LA3711 LA mm - hook LA3712 LA mm - loop LA3713 LA mm - hook LA4040 LA mm - loop LA4041 LA mm - hook LA3716 LA mm - loop LA3717 LA3778 Hook & loop - elasticated sold per metre /type white beige 30mm - hook LA3914 LA mm - loop LA3915 LA mm - hook LA3924 LA mm - loop LA3925 LA3965 Hook & loop - adhesive backed sold per metre white beige /type white beige 30mm - hook LA3814 LA mm - loop LA3815 LA mm - hook LA3824 LA mm - loop LA3825 LA3865 Plastazote Plastazote foams have widespread uses in orthopaedic manufacturing. A thermoplastic polyethylene foam, Plastazote is easily heat moulded ( C) and will adhere to most materials. Plastazote 1.5m x 1.0m colour material ON1103 white 3mm LD45 ON1106 white 6mm LD45 ON1108 white 12mm LD45 ON1143 red 3mm LD45 ON1146 red 6mm LD45 ON1148 red 12mm LD45 ON1153 blue 3mm LD45 ON1156 blue 6mm LD45 ON1158 blue 12mm LD45 Plastazote 1.5m x 1.0m colour material ON1012 white 3mm LD45 ON1014 white 6mm LD45 Order your full Algeos catalogue To view Algeos full product range, including our full comfort sheet offering, appliance fastenings and other orthopaedic materials, please call us or visit us on the Internet at: 8 further information:

9 Cushioning PORON 96 - Jade Green (Slow Memory Medical Grade) PORON Medical Slow Recovery urethane is a unique custom contouring material. This material rebounds slowly when compressed, which results in a custom fit or contour during each use. The material will return to its original shape when not in use. PORON Blue (Medical Grade) Specially developed for the medical sector, Blue PORON 4708 has passed numerous medical assessments for biological response. PORON 4708 is commonly used in orthopaedic applications, including custom orthotics, prosthetic padding, splint padding and other biomechanical supports. Poron 4708 blue medical grade m x 1.00m OB mm OB mm OB mm Poron 96 jade green medical m x 1.00m OB mm OB mm Evazote EV50 Similar to LD24 Plastazote, but more resistant in abrasive applications. Evazote is heat mouldable at 140 C C Evazote 1.5m x 1.0m colour ON1052 3mm blue ON1054 6mm blue ON1056 3mm white ON1058 6mm white ON mm white Maxcane Elastomer Gel Maxacane Elastomer Gel is a soft, non-abrasive material, which acts like human fatty tissue to cushion bony protrusions and pressure sensitive skin. The key to the Gel's effectiveness is its ability to displace weight evenly thus preventing one area from receiving all the pressure. Maxacane elastomer gel 0.35m x 0.5m OB2402 2mm OB2403 3mm OB2406 6mm our full range: 9

10 Modification tools Thermoplastic Water Bath Exterior is constructed from sheet steel finished in an easy clean powder coated paint. The interior is constructed of stainless steel with a perforated tray covering the heating element. Control is via an easy set thermostat with indicator and an on/off switch. Can heat water up to 100 C. Internal dimensions: 30 x 50 x 15cm. 240V mains. Thermoplastic water bath LM litre bath (with lid) Clarke Band Saw This three wheeled, variable speed bandsaw allows accurate and precise cutting. Maximum cutting height of 80mm, with 305mm throat depth. 345mm x 345mm cast aluminium table tilts from 0 to 45 for bevel cutting. 1,575mm blade length with variable speed control between 470 & 630 m/min. Mitre guide & safety switch included as standard. 500 Watts, 230v motor. Clarke band saw LM1106 band saw - wide throat Bosch Heat Gun Efficient and dependable heat gun, ideal for simple Multicast manipulations. This particular model has a variable heat setting of c and a nozzle diameter of 25mm. Bosch heat gun LM v heat gun 10 further information:

11 Tools & fastenings Revolving punch pliers kretzer shears LA1882 heavy duty punch pliers LA1884 punch set (pack of 6) Bruns cast shears 22cm length Hand pliers for tubular rivets LA4605 straight Edge de-burring tool LA4618 mundial serra sharp scissors LA4088 hand pliers only LA2681 dies set for tub rivets Nylon chafes LA4600 8" Nickel plated tubular rivets stem cap LA2432 de-burring tool 9mm LA1722 LA1702 LA2434 blades (pack of 10) 10mm LA1726 LA1706 Nylon loops Nylon sewable tabs sold in units of 1000 sold in units of 1000 white beige 25mm LA3256 LA3261 LA mm 38mm LA3257 LA3263 LA mm 50mm LA3258 LA3265 LA mm Rectangular wire frames sold in units of 1000 Wire loops with nylon roller sold in units of 1000 sold in units of 1000 white beige 25mm LA3266 LA3276 LA mm LA mm 38mm LA3267 LA3277 LA mm LA mm 50mm LA3268 LA3278 LA mm LA mm LA mm our full range: 11

12 Multicast usage tips: Place the patient on a table, in an ergonomic position. Begin by ensuring which movements in hand or foot are possible. Check the condition of the skin. Use a pattern or draw an approximate model to avoid material waste. Take pieces of Multicast from the hot-water bath in a folded position. On using a heat gun, touch the weakened Multicast with wet fingers. Optimal heat conduction can be obtained by turning over the material onto a moistened towel (preferably a bath towel) immediately after the surface has weakened, before continuing the treatment. The hardening period can be reduced by applying cold water, ice cubes or a cold spray. Try to limit stretching the material. A cut out model has sharp edges, which can be smoothed away by dipping the edges into the hot water for 3 seconds and then smoothing them with the fingers. Cast fastenings can be made using hook and loop. This is the simplest and fastest way of fastening. By heating the Multicast locally and superficially with a heat gun, it is possible to push the loops strip down on to the soften surface. To prevent energy impact inside the cast, a cushioning material can be adhered to problem areas. Where epidermititis might be a risk, ensure the patient wears a stockinette lining under the thermoplastic, renewing it daily. Purchasing information: tel: +44 (0) Monday to Friday 8am - 5pm Answering service 5pm - 8pm delivery: Same day despatch on all instock items. Free delivery on all orders over 500 fax: (0) sales@algeos.com payment: For private-sector first order customers, we will require payment by credit card or cheque. We accept most major credit cards. web: (online purchasing) mail: A. Algeos Ltd. Sheridan House Bridge Industrial Estate Speke Hall Road Liverpool, UK L24 9HB all these products can be bought online at