UPDATE TO STANDARD EN 388 GLOVES GIVING PROTECTION FROM MECHANICAL RISKS

Size: px
Start display at page:

Download "UPDATE TO STANDARD EN 388 GLOVES GIVING PROTECTION FROM MECHANICAL RISKS"

Transcription

1 UPDATE TO STANDARD EN 388 GLOVES GIVING PROTECTION FROM MECHANICAL RISKS

2 EN 388 THIS STANDARD APPLIES TO ALL KINDS OF PROTECTIVE GLOVES IN RESPECT OF PHYSICAL AND MECHANICAL AGGRESSIONS CAUSED BY ABRASION, BLADE CUT, PUNCTURE AND TEARING A revised version of the EN 388 standard was released in November 2016 and is referred to as EN 388:

3 EN 388:2003 Every glove tested under EN 388:2003 achieved a performance rating expressed by a pictogram, followed by four numbers representing performance against each specific hazard. The higher the numerical rating (0-4 for abrasion, tear and puncture / 0-5 for blade cuts), the higher the protection offered VS EN 388:2016 THE NEW STANDARD A number of changes are effective under the new EN 388 standard. The most significant change has been to the cut resistance testing. Designed to keep pace with the development of cut resistant fibres, the new standard is designed to address flaws in the cut test methodology applied as part of EN 388:2003. This enables safety managers to better match the protection required against the hazards encountered by the workforce. In instances where the blade in the coup test experiences blunting, an additional test is carried out - EN ISO In addition, new testing protocols covering abrasion and impact resistance have been created. All such changes are explained in more detail within this document. The changes to the standard affect new products being certified. Distributors have until 21 st April 2023 to sell through any stocks of product certified to the EN 388:2003 standard. 3

4 CUT RESISTANCE Although EN 388:2003 results were seen as a satisfactory indicator for gloves with lower cut resistance, a number of flaws were identified for those with higher cut resistance (cut levels 4-5). The liners used with the latter that are blended with glass-fibre can blunt the microscopic edge of the blade used in the Coup Test, whilst steel-based engineered yarns can stop the testing machine due to metal-to-metal contact without necessarily cutting through the material. As a result, potentially large performance variances and inconsistent cut indices exist. The 2003 version of the standard used the Coup Test method only to indicate cut resistance performance. COUP TEST LINEAR MOVEMENT OF BLADE FIXED FORCE APPLIED FROM ABOVE 5N Rotating Blade LINEAR MOVEMENT OF BLADE This test results in a cut index score and is based on a free rotating circular blade, under a standard 5N contact force, tracking backwards and forwards over a flat surface of the test material. Fabric Sample SAMPLE HOLDER In the 2016 version, the Coup Test is still used but if the blade become dull (by a factor of 3 or above after the second reference fabric cut) the EN ISO cut resistance method then becomes the reference test method for the assessment of the protection against cut risks. In this instance, an X may be displayed in the place of a Coup Test result as the second digit under the EN 388 pictogram. 4

5 EN ISO TEST Curved Test Device Surface LINEAR MOVEMENT OF BLADE Blade Sample of Fabric Thin Plastic Film (used when fabric includes steel yarn) Using a straight blade in testing, the EN ISO method measures the average load required to achieve a cut, after the blade has travelled once over a 20mm distance. VARIABLE FORCE APPLIED FROM BELOW (simulates a mass being placed on top of the blade) EN ISO cut resistance performance levels (measured in Newtons (N)) will be indicated by a six-letter classification system. Level A Level B Level C Level D Level E Level F EN ISO CUT TEST 2N 5N 10N 15N 22N 30N This will see the additional straight blade performance level result added as a 5 th digit under the EN 388 pictogram. The Coup Test method has also been revised which sees the number of test cycles limited to 60 (whether the blade has cut through the fabric or not) to prohibit endless testing. 5

6 ABRASION RESISTANCE The type of abrasive paper used in the test has been changed. DUE TO THE CHANGE, SOME ABRASION SCORES MAY CHANGE WHEN TESTED TO THE NEW STANDARD. To measure the abrasion resistance of a glove, the glove material is fitted to a Martindale abrasion machine and the rubbing head moves over the test material in an elliptical motion over a table covered with 180 grit abrasive material. The EN 388:2003 version specified a 100 grit material. The number of cycles required to make a hole in the test material relate to the 1-4 levels of abrasion performance. 6

7 IMPACT RESISTANCE A new addition within the EN 388:2016 standard is an optional test to measure the impact protection of a glove that claims to have impact resistant properties. This test is carried out in accordance with EN 13594: Protective Gloves for Motorcycle Riders. The area/material of impact protection is tested by being secured to a domed anvil and impacted with a 2.5kg flat face striker and energy of 5J. Gloves must meet the requirement of level 1 of EN 13594: the mean transmitted force shall be 7.0kN with no single results greater than 9.0kN. P IF THE GLOVE MEETS THIS REQUIREMENT, A P IS ADDED AS THE LAST DIGIT TO THE EN 388:2016 GLOVE MARKING. 7

8 MARKINGS The pictogram will not change, however, when a glove has been tested to the EN 388:2016 standard, you can understand the new markings as below: E P Abrasion Resistance Circular Blade Cut Resistance (Coup Test) Tear Resistance Puncture Resistance Straight Blade Cut Resistance (ISO Test) Impact Resistance RATING: A-F P NOTE: If tests are not performed or are not applicable, X will be placed instead of a number/letter. (See pages 4 and 7) 0 may be shown if level 1 is not achieved. For advice on glove suitability for your application please contact us: Tel: +44 (0) sales@globus.co.uk 2017 Globus (Shetland) Ltd GLOBUS-WP-EN _2

ISO INTERNATIONAL STANDARD

ISO INTERNATIONAL STANDARD INTERNATIONAL STANDARD ISO 12947-1 First edition 1998-12-15 Textiles Determination of the abrasion resistance of fabrics by the Martindale method Part 1: Martindale abrasion testing apparatus Textiles

More information

The Bombay Textile Research Association, L. B. S. Marg, Ghatkopar (West), Mumbai, Maharashtra. Discipline Mechanical Testing Issue Date

The Bombay Textile Research Association, L. B. S. Marg, Ghatkopar (West), Mumbai, Maharashtra. Discipline Mechanical Testing Issue Date Last Amended on - Page 1 of 7 I. TEXTILES & RELATED PRODUCTS 1. FIBRES Neps in Cotton Fibres (AFIS-N-Instrument) Physical Properties of Cotton Fibres by High Volume Instrument (HVI) 2.5% Span Length Uniformity

More information

Pencil Hardness Tester BEVS 1301

Pencil Hardness Tester BEVS 1301 Pencil Hardness Tester BEVS 1301 User Manual PAGE 1 1. Introduction BEVS pencil hardness tester offers an easy to use method for the determination of film hardness for a coating applied to a flat substrate,

More information

OxFAC-08 Angled Fiber Cleaver. User Manual. Issue 1.5

OxFAC-08 Angled Fiber Cleaver. User Manual. Issue 1.5 OxFAC-08 Angled Fiber Cleaver User Manual Issue 1.5 Contents Issue & Scope... 2 Introduction... 2 Contents of Cleaving Kit & Unpacking... 3 Cleaving Problems... 8 Blade damage:... 9 Cleaver Maintenance...

More information

119 Lab 1: Resonances and Standing Waves

119 Lab 1: Resonances and Standing Waves 119 Set Up Lists 119 Lab 1: Resonances and Standing Waves Equipment List Set Up 1 PASCO Wave Generator 1 Stand with 2 2kg Weights 1 PASCO Function Generator and Wires (1 Red and 1 Black) 1 ~1.25m Neon

More information

Sabre Series 2 Inspired Design Precision Engineering

Sabre Series 2 Inspired Design Precision Engineering Sabre Series 2 Inspired Design Precision Engineering USER INSTRUCTIONS Thank you for choosing the Keencut Sabre Series 2. Every effort has been made to bring you a precision engineered product with the

More information

Discipline Mechanical Testing Issue Date Certificate Number T-2218 Valid Until Last Amended on

Discipline Mechanical Testing Issue Date Certificate Number T-2218 Valid Until Last Amended on Last Amended on 19.05.2014 Page 1 of 5 I. TEXTILES & RELATED PRODUCTS 1. Garment / Fabric Mass per unit area (weight) of fabric ASTM D3776M-09a (Option C) ISO 3801 : 1977(Method 5) BS EN ISO 12127:1998

More information

GESTER INTERNATIONAL CO.,LTD TEL: FAX:

GESTER INTERNATIONAL CO.,LTD TEL: FAX: Shoes Accessories Testing Equipment GT-K19 Velcro Fatigue Tester This tester is applicable for repeatedly open and close motion for touch and close fasteners and velcro tapes. DIN 3415, BS EN ISO 22776,

More information

Optical Information. The LDM145 laser diode modules are available with the following lens types.

Optical Information. The LDM145 laser diode modules are available with the following lens types. LDM145 Datasheet LDM145 The LDM145 is a 16mm diameter CW laser diode module available in wavelengths of 520, 635, 650, 670, 780 & 850nm with power of up to 5mW as standard. It reuires an operating voltage

More information

3133 Ninja Catalog_JNINJA_05-15-v4c_Layout 1 5/26/15 10:02 AM Page 1 Ninja

3133 Ninja Catalog_JNINJA_05-15-v4c_Layout 1 5/26/15 10:02 AM Page 1 Ninja 1 Ninja Catalog_JNINJA_05-15-v4c_Layout 1 5/26/15 10:02 AM Page 1 Ninja Multi-Purpose - BNF N96790 Memphis Ninja BNF 15-Gauge, Gray Nylon/Spandex Shell with Black BNF (Breathable Nitrile Foam) Technology

More information

PREMIUM CUT RESISTANT-WORK GLOVES CUT RESISTANT-WORK GLOVES WITH DUPONT KEVLAR. Professional Grade Coated Work Gloves MULTI-PURPOSE WORK GLOVES

PREMIUM CUT RESISTANT-WORK GLOVES CUT RESISTANT-WORK GLOVES WITH DUPONT KEVLAR. Professional Grade Coated Work Gloves MULTI-PURPOSE WORK GLOVES PREMIUM CUT RESISTANT-WORK GLOVES Professional Grade Coated Work Gloves CUT RESISTANT-WORK GLOVES WITH DUPONT KEVLAR MULTI-PURPOSE WORK GLOVES ROC is... R eliable protection. Outstanding dexterity. C omfortable

More information

REDEFINING HAND PROTECTION

REDEFINING HAND PROTECTION REDEFINING HAND PROTECTION PROTECTIVE INDUSTRIAL PRODUCTS, INC. BRINGING THE BEST OF THE WORLD TO YOU A NEW APPROACH BASED ON REAL LIFE USE AND RISK Over the years, the industry has struggled to equate

More information

Processing and design Solid Textile Board

Processing and design Solid Textile Board Processing and design Solid Textile Board List of contents Introduction Kerfing Joints and assembly Increasing thickness and stiffness Edges Cutting Milling and drilling Three-dimensional pressing Surface

More information

In 1950, plastic film was relatively

In 1950, plastic film was relatively TECHNICAL REPORT BY REINHOLD SCHABLE, APPLICATIONS TECHNOLOGY MANAGER, TIDLAND CORP. Slitting Technology for Film Substrates In 1950, plastic film was relatively uncommon, today it is everywhere. Back

More information

Cutting, Grinding and Abrasive Accessories

Cutting, Grinding and Abrasive Accessories High quality range of abrasive cutting discs, grinding discs and surface preparation accessories engineered for ultimate performance Universal Diamond Blades Cutting and Grinding Discs The essential construction

More information

Traditional Tool Shapes & Applications 1/

Traditional Tool Shapes & Applications 1/ Traditional Tool Shapes & Applications 1/ Most of the tools listed and discussed in this document have over 1000 years of history behind them and until relatively recent (the last 300 years) a striker

More information

GCSE Design and Technology Short Course

GCSE Design and Technology Short Course GCSE Design and Technology Short Course Paper 1 Mark scheme 45751 June 2013 Version: Final Mark Scheme Mark schemes are prepared by the Lead Assessment Writer and considered, together with the relevant

More information

Test Report. No.399 Gang Wen Road, Fengxian District Shanghai, China Tel:(86-21) Fax:(86-21) Test Report No.

Test Report. No.399 Gang Wen Road, Fengxian District Shanghai, China Tel:(86-21) Fax:(86-21) Test Report No. No.399 Gang Wen Road, Fengxian District Shanghai, China 201413 Tel:(86-21) 3755 4800 Fax:(86-21) 3755 4819 Test Report Test Report No.: 26705887 Issue Date: 260913(DDMMYY) Client Information: Supplier

More information

PUNCTURE AND TEAR OF WOVEN FABRICS

PUNCTURE AND TEAR OF WOVEN FABRICS PUNCTURE AND TEAR OF WOVEN FABRICS Dr. Anthony Primentas Associate Professor Department of Textile Engineering, ΤΕΙ of Piraeus ABSTRACT The quite often contact of textile goods with sharp objects, results

More information

DRAFT UGANDA STANDARD

DRAFT UGANDA STANDARD DRAFT UGANDA STANDARD DUS DEAS 222 First Edition 2016-mm-dd Knitted polyester/cellulosic blended fabric Specification PUBLIC REVIEW DRAFT Reference number DUS DEAS 222: 2016 UNBS 2016 DUS DEAS 222:2016

More information

Washability & Abrasion. elcometer.com. Elcometer 1720 Washability & Abrasion Testers

Washability & Abrasion. elcometer.com. Elcometer 1720 Washability & Abrasion Testers elcometer.com 1 AS/NZS 1580.459.1, ASTM D 2486, ASTM D 3450, ASTM D 4213, ASTM D 4488, ASTM D 4828, ASTM F 1319, DIN 53778-2:1983, ECCA T11, EN 12956, EN 13523-11, EN 233/C3.2-A, EN 233/C3.2-B, EN 233/C3.2-C,

More information

UNCONTROLLED 3 STANDARD PROCEDURES FOR PREPARING 33KV CABLES

UNCONTROLLED 3 STANDARD PROCEDURES FOR PREPARING 33KV CABLES 3 STANDARD PROCEDURES FOR PREPARING 33KV CABLES 3.1 Single-Core Copper Wire Screened Polymeric Cables 3.1.1 Removing the Outer Sheath Clean and abrade the outer sheath with an approved abrasive paper for

More information

College of Forestry 610: Power Tools

College of Forestry 610: Power Tools College of Forestry 610: Power Tools Safety Policy & Procedure Manual Section 600: Workshops and Shop Tools Effective: 01 January 2007 Revised: August 2014 PURPOSE The purpose of this section is to provide

More information

Ring crush of paperboard (flexible beam method) (REAFFIRMATION of Classical Method T 818 cm-07) (No changes from previous drafts)

Ring crush of paperboard (flexible beam method) (REAFFIRMATION of Classical Method T 818 cm-07) (No changes from previous drafts) NOTICE: This is a DRAFT of a TAPPI Standard in ballot. Although available for public viewing, it is still under TAPPI s copyright and may not be reproduced or distributed without permission of TAPPI. This

More information

FLAT WOVEN, PILE WOVEN AND PRESSED FELT APPAREL FABRICS. Woolmark, Woolmark Blend or Wool Blend labelling may be applied to woven fabric:

FLAT WOVEN, PILE WOVEN AND PRESSED FELT APPAREL FABRICS. Woolmark, Woolmark Blend or Wool Blend labelling may be applied to woven fabric: SPECIFICATION SF-2: 2016 FLAT WOVEN, PILE WOVEN AND PRESSED FELT APPAREL FABRICS FABRICS Woolmark, Woolmark Blend or Wool Blend labelling may be applied to woven fabric: Woolmark Blend and Wool Blend labelling

More information

Preliminary Version. Working with the Blade of the Opus1 Gouger Robin Driscoll October 2003

Preliminary Version. Working with the Blade of the Opus1 Gouger Robin Driscoll October 2003 Preliminary Version Working with the Blade of the Opus1 Gouger Robin Driscoll October 2003 One of the most interesting aspects of the Opus1 Gouger is the multitude of adjustments that are now easily in

More information

Tidland Slitter Shafts

Tidland Slitter Shafts TIDLAND SLITTING SOLUTIONS Tidland Slitter Shafts Installation, Operation and Maintenance EN MI 666265 1 D Knife Shaft (tubular) KT Knife Shaft (solid) KS Anvil Roll (KS with sleeves) AR IMPORTANT SAFETY

More information

Javelin Integra Inspired Design Precision Engineering

Javelin Integra Inspired Design Precision Engineering Javelin Integra Inspired Design Precision Engineering USER INSTRUCTIONS Thank you for choosing the Keencut Javelin Integra. Every effort has been made to bring you a precision engineered product with the

More information

Ox-RAC-08 Ribbon Angled Fiber Cleaver User Manual

Ox-RAC-08 Ribbon Angled Fiber Cleaver User Manual Ox-RAC-08 Ribbon Angled Fiber Cleaver User Manual Issue 2.0 Contents Introduction... 2 Contents of Cleaving Kit & Unpacking... 3 Cleaving Problems... 8 Blade damage:... 9 Cleaver Maintenance... 10 Cleaning

More information

TYPE 3740XL EXTRA LARGE WET RUNNING CARTRIDGE SPLIT SEAL

TYPE 3740XL EXTRA LARGE WET RUNNING CARTRIDGE SPLIT SEAL 1 Foreword These instructions are provided to familiarize the user with the seal and its designated use. The instructions must be read and applied whenever work is done on the seal, and must be kept available

More information

3M Impact Protection Profile Installation System Instructions

3M Impact Protection Profile Installation System Instructions 3M Impact Protection Profile Installation System Instructions IMPORTANT: READ INSTRUCTIONS FOR USE BEFORE OPERATING Intended Use: The 3M Impact Protection Profile Installation System is for installing

More information

Weber s Guide to GHS Labeling. Get the answers to your GHS questions!

Weber s Guide to GHS Labeling. Get the answers to your GHS questions! Weber s Guide to GHS Labeling Get the answers to your GHS questions! Chemical labeling requirements are changing. Make sure your company is ready. Thre old HCS Requirements The basics of GHS labeling Who

More information

Splashback Installation Instructions

Splashback Installation Instructions Splashback Installation Instructions What is Akril? Akril is an Australian made environmentally friendly, highly engineered polymer, enhanced with colour. Quite simply, it offers a new source of design

More information

MANUFACTURE GUIDELINES

MANUFACTURE GUIDELINES PRE-INSTALLATION CHECKS Ensure cabinets are fitted correctly and level prior to installing the Evostone work surface. It is a condition of the Evostone 10 year limited warranty that before any fabrication

More information

Peel Adhesion of Pressure Sensitive Tape

Peel Adhesion of Pressure Sensitive Tape Harmonized International Standard Peel Adhesion of Pressure Sensitive Tape Call Letters Date of Issuance Revised Revised Revised PSTC 101 10/00 10/03 05/07 11/13 1. SCOPE 1.1 These methods cover the measurement

More information

BuzziBlinds Classic Product Specification Sheet

BuzziBlinds Classic Product Specification Sheet BuzziBlinds Classic Product Specification Sheet This document contains technical information about the BuzziBlinds Classic www.buzzi.space Room divider These rotating acoustic blinds take their inspiration

More information

Elcometer Cross Hatch Cutter. Operating Instructions

Elcometer Cross Hatch Cutter. Operating Instructions Elcometer 107 1542 English Cross Hatch Cutter Operating Instructions English is a registered trademark of Elcometer Limited. All other trademarks acknowledged. Copyright Elcometer Limited. 2009. All rights

More information

SAWING MADE IN GERMANY

SAWING MADE IN GERMANY 106 SAWING MADE IN GERMANY JIGSAW, RECIPROCATING SAW Product characteristics STAR teeth Conically ground blade, teeth triply sharpened. Benefits : Extreme fast, precise and clean cuts il all wood and plastics.

More information

SlipGrip Data Sheet & Installation Guide

SlipGrip Data Sheet & Installation Guide SlipGrip Data Sheet & Installation Guide Stair Treads Landing Covers Flat Sheets 9/2015 SlipGrip Technical Data Description SlipGrip products are high performance safety stair treads, landing covers and

More information

ISO INTERNATIONAL STANDARD. Textiles Determination of fabric propensity to surface fuzzing and to pilling Part 2: Modified Martindale method

ISO INTERNATIONAL STANDARD. Textiles Determination of fabric propensity to surface fuzzing and to pilling Part 2: Modified Martindale method INTERNATIONAL STANDARD ISO 12945-2 First edition 2000-07-01 Textiles Determination of fabric propensity to surface fuzzing and to pilling Part 2: Modified Martindale method Textiles Détermination de la

More information

Orthographic Projection

Orthographic Projection Orthographic Projection Why Orthographic Projection is used in technical drawing Orthographic projection is a method of producing a number of separate two-dimensional inter-related views, which are mutually

More information

GB/T Translated English of Chinese Standard: GB/T

GB/T Translated English of Chinese Standard: GB/T Translated English of Chinese Standard: GB/T4808.2-2008 www.chinesestandard.net Sales@ChineseStandard.net GB NATIONAL STANDARD OF THE PEOPLE S REPUBLIC OF CHINA ICS 9.080.30 W04 GB/T 4802.2-2008 Replacing

More information

BuzziDesk Product Specification Sheet

BuzziDesk Product Specification Sheet Product Specification Sheet This document contains technical information about the www.buzzi.space Desk divider screen with metal profile Not only does the safeguard your privacy at work; it keeps out

More information

INTRODUCTION TO GRINDING PROCESS

INTRODUCTION TO GRINDING PROCESS GRINDING PART 2 Grinding Grinding is a material removal process accomplished by abrasive particles that are contained in a bonded grinding wheel rotating at very high surface speeds. The rotating grinding

More information

ABRASIVE CATALOGS. Application: Weld dressing Cutting off smoothing of Casting Can be applied on various kind of Steel and non-ferrous materials

ABRASIVE CATALOGS. Application: Weld dressing Cutting off smoothing of Casting Can be applied on various kind of Steel and non-ferrous materials ABRASIVE CATALOGS Reinforced Depressed Centre Grinding Discs are excellently fabricated depressed centre grinding discs that are exclusively available in varying diameters of 4-9 in different thickness.

More information

PRODUCT CATALOGUE. A Company within the SWAROVSKI Group

PRODUCT CATALOGUE. A Company within the SWAROVSKI Group PRODUCT CATALOGUE A Company within the SWAROVSKI Group TABLE OF CONTENT TYROLIT Quality Lines Page 3 TYROLIT Labels Page 4 Cut-Off Wheels for Angle Grinders Page 5-6 Premium Line - Cut-off wheels Standard

More information

TECHNICAL FEATURES GLOVE

TECHNICAL FEATURES GLOVE TECHNICAL FEATURES GLOVE 02/2018 STATIONARY CHAIR 4-LEGGED CHAIR Perforated polypropylene (variable thickness of 6-8 mm) / Fully upholstered (foam thickness of 5 mm) / Wooden (10 mm thick beech polylaminated)

More information

2017 VCE VET Furnishing examination report

2017 VCE VET Furnishing examination report 2017 VCE VET Furnishing examination report General comments The 2017 VCE VET Furnishing examination assessed students underpinning knowledge of the competencies they had undertaken in Units 3 and 4 as

More information

Experts in Safety. Quality and Product Assurance

Experts in Safety. Quality and Product Assurance Experts in Safety Quality and Product Assurance Arco Product Quality and Assurance We don t just develop products to meet standards, we aim to exceed them... and if our experience tells us that the standards

More information

Polishing of Fibre Optic Connectors

Polishing of Fibre Optic Connectors STR/3/27/MT Polishing of Fibre Optic Connectors L. Yin, H. Huang, W. K. Chen, Z. Xiong, Y. C. Liu and P. L. Teo Abstract - This study reports the development of high efficiency polishing protocols of fibre

More information

Technical Training International Textiles Training September 2018 Ellen Roaldi Instructor

Technical Training International Textiles Training September 2018 Ellen Roaldi Instructor Technical Training International Textiles Training September 2018 Ellen Roaldi Instructor www.astm.org D3512 Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics:

More information

Foreign Particulate Matter testing using the Morphologi G3

Foreign Particulate Matter testing using the Morphologi G3 Foreign Particulate Matter testing using the Morphologi G3 Introduction The Morphologi G3 with its Foreign Particle Detection capabilities allows the detection, enumeration and size classification of foreign

More information

As the UK s oldest ink maker since 1786, we at Druckfarben of lithographic inks suitable for all

As the UK s oldest ink maker since 1786, we at Druckfarben of lithographic inks suitable for all INKS Druckfarben is a world leader in the manufacture, sale and distribution of commercial printing inks and press related consumables. With a global network of distributor partners and a Head Office in

More information

ZHM CT Series. Technical Datasheet. Gear Flow Meters in Cartridge Design for paint applications, optimized with regard to flushing and to weight

ZHM CT Series. Technical Datasheet. Gear Flow Meters in Cartridge Design for paint applications, optimized with regard to flushing and to weight www.kem-kueppers.com Technical Datasheet ZM CT Series Gear Flow Meters in Cartridge Design for paint applications, optimized with regard to flushing and to weight Certified zertifiziert according gemäß

More information

MERRIDALE STREET WEST WOLVERHAMPTON

MERRIDALE STREET WEST WOLVERHAMPTON Instructions Boring "Wandess" Cylinder Boring Bar Whatton & Sons, Ltd MERRIDALE STREET WEST WOLVERHAMPTON The "Wandess" Cylinder Boring Bar GENERAL : Introduction of the Wandess Cylinder Boring Bar marks

More information

BuilDing & EnginEEring SErvicES ASSociAtion SPECIFICATION FOR SHEET METAL DUCTWORK DW/144. Second Edition

BuilDing & EnginEEring SErvicES ASSociAtion SPECIFICATION FOR SHEET METAL DUCTWORK DW/144. Second Edition BuilDing & EnginEEring SErvicES ASSociAtion SPECIFICATION FOR SHEET METAL DUCTWORK DW/144 Second Edition 2013 www.b-es.org DW/144 Specification for Sheet Metal Ductwork Low, medium and high pressure/velocity

More information

SHELDON Versatile seating

SHELDON Versatile seating UK street furniture designers & manufacturers As UK based, designers and manufacturers, Street Design can manufacture and supply Sheldon seating to suit your specific requirements. Sheldon versatile seating

More information

STRIKER TABLE FOOTBALL GAME

STRIKER TABLE FOOTBALL GAME STRIKER TABLE FOOTBALL GAME ASSEMBLY INSTRUCTIONS Please keep for future reference Adult Assembly Required (0316) 1 ASSEMBLY INSTRUCTIONS Please keep these instructions for future reference. Adult assembly

More information

Woodware Designs -- Furniture Construction Hints

Woodware Designs -- Furniture Construction Hints Woodware Designs -- Furniture Construction Hints 1. Purpose The following are construction hints for woodworking details used in building many of our desks. We are providing them here free for our woodworking

More information

Make a Portable Hibachi

Make a Portable Hibachi Metal Work Description The purpose of this activity plan is to introduce students to the metal shop through a practical activity. Students will gain valuable knowledge in using power tools and equipment

More information

ARA FRAMES. Premium Range

ARA FRAMES. Premium Range ARA FRAMES Premium Range ARA PLUS Images shown are for presentation purpose only, colour may vary depending upon the materials available Sizes mentioned are approximately nearest ARA PLUS A 10-26 A 10-30

More information

Extruded sheet (FF) #3 Other Methods of Cutting. Technical information. This brief gives advice for:

Extruded sheet (FF) #3 Other Methods of Cutting. Technical information. This brief gives advice for: Technical information Extruded sheet (FF) WARNING: This product can expose you to chemicals including Ethyl acrylate, CAS 140-88-5, which are known to the State of California to cause cancer. For more

More information

UNPACK & ASSEMBLY. Done! CAUTION! THE MILL WILL BE VERY HEAVY - GET ASSISTANCE Pepe Tools.

UNPACK & ASSEMBLY. Done! CAUTION! THE MILL WILL BE VERY HEAVY - GET ASSISTANCE Pepe Tools. PARTS DIAGRAM T Bar Height adjustment Wooden hand grip Height adjustment gears Frame Height adjustment screws Top roller End Gears cover Handle Brass Bushes (Each side) Bottom roller 4:1 Gearbox Mounting

More information

STUDENT/FACULTY MACHINE SHOP SAFETY RULES

STUDENT/FACULTY MACHINE SHOP SAFETY RULES STUDENT/FACULTY MACHINE SHOP SAFETY RULES Supervisors have full authority over the shop and its safe use, including the responsibility, authority, and obligation to prohibit shop or tool access for the

More information

Guidelines for working with

Guidelines for working with Guidelines for working with 1. Sawing Circular Saws When using circular saws, only the circular saw blades that are not set are suitable for cutting PARAPAN. Hardened metal saw blades that have the greatest

More information

Chapter 25. Other Machining Processes. Materials Processing. MET Manufacturing Processes. Shaping Planing Broaching Sawing Filing

Chapter 25. Other Machining Processes. Materials Processing. MET Manufacturing Processes. Shaping Planing Broaching Sawing Filing MET 33800 Manufacturing Processes Chapter 25 Other Machining Processes Before you begin: Turn on the sound on your computer. There is audio to accompany this presentation. Other Machining Processes Shaping

More information

THREAD CUTTING & FORMING

THREAD CUTTING & FORMING THREAD CUTTING & FORMING Threading, Thread Cutting and Thread Rolling: Machining Threads on External Diameters (shafts) Tapping: Machining Threads on Internal Diameters (holes) Size: Watch to 10 shafts

More information

Physical laboratory testing equipment

Physical laboratory testing equipment Zehntner GmbH Testing Instruments Baerenmattenstrasse 3 CH-4434 Hoelstein Switzerland Tel +41 61 953 05 50 Fax +41 61 953 05 51 zehntner@zehntner.com www.zehntner.com Physical laboratory testing equipment

More information

100 s of Tasks with One Tool

100 s of Tasks with One Tool The ULTIMATE Guide to STARLOCK OSCILLATING TOOL ACCESSORIES 100 s of Tasks with One Tool Ask about Task Starlock accessories where you buy tools, or visit www.tasktools.com to purchase or get more information.

More information

TUCANA-02 P PORTABLE END MILLING MACHINE USER S MANUAL

TUCANA-02 P PORTABLE END MILLING MACHINE USER S MANUAL TUCANA-02 P PORTABLE END MILLING MACHINE USER S MANUAL 1 CONTENTS Page 1. General Information 3 1.1. Introduction 3 1.2. Manufacturer 3 2. Machine s Description and Purpose of Use 3 2.1. Machine s description

More information

Fibre Technology Laboratory

Fibre Technology Laboratory Fibre Technology Laboratory Test code T 001 T 002 Description of test Determination of oil/wax content Analysis of fibre mixtures/blends Standard Test Method IWS TM 136 One fibre ISO1833: 2006 Two fibres

More information

INTERNATIONAL STANDARD

INTERNATIONAL STANDARD INTERNATIONAL STANDARD ISO 1888 Third edition 2006-07-01 Textile glass Staple fibres or filaments Determination of average diameter Verre textile Fibres discontinues et filaments Détermination du diamètre

More information

Fitting & Turning. NQF Level 2. LL Maraschin LECTURER S GUIDE TVET FIRST

Fitting & Turning. NQF Level 2. LL Maraschin LECTURER S GUIDE TVET FIRST Fitting & Turning NQF Level 2 LL Maraschin LECTURER S GUIDE TVET FIRST Fitting & Turning NQF Level 2 Lecturer s Guide LL Maraschin Fitting & Turning NQF Level 2 Lecturer s Guide LL Maraschin, 2012 All

More information

Producing platework components and assemblies. Outcome one

Producing platework components and assemblies. Outcome one 006 UNIT 023 Producing platework components and assemblies Learning outcomes 1 2 Know how to produce platework components and assemblies Performance evidence must be the main form of evidence gathered.

More information

Flat Glazing FLEXIBLE LIGHT IN WEIGHT RANGE OF SIZES. Acrylic Sheet Exterior Polystyrene Sheet Interior Grade Solid Polycarbonate Sheet

Flat Glazing FLEXIBLE LIGHT IN WEIGHT RANGE OF SIZES. Acrylic Sheet Exterior Polystyrene Sheet Interior Grade Solid Polycarbonate Sheet INSTALLATION GUIDE Flat Glazing FLEXIBLE LIGHT IN WEIGHT RANGE OF SIZES Acrylic Sheet Exterior Polystyrene Sheet Interior Grade Solid Polycarbonate Sheet Flat Glazing IMPORTANT These instructions are guidelines

More information

Lathe is a machine, which removes the metal from a piece of work to the required shape & size HENRY MAUDSLAY

Lathe is a machine, which removes the metal from a piece of work to the required shape & size HENRY MAUDSLAY TURNING MACHINES LATHE Introduction Lathe is a machine, which removes the metal from a piece of work to the required shape & size HENRY MAUDSLAY - 1797 Types of Lathe Engine Lathe The most common form

More information

O N T H E C U T T I N G E D G E O F T E C H N O L O G Y

O N T H E C U T T I N G E D G E O F T E C H N O L O G Y A B R A S I V E P R O D U C T S C A T A L O G U E O N T H E C U T T I N G E D G E O F T E C H N O L O G Y Founded in 1981, Grinding Techniques (Pty) Ltd. is the largest privately owned abrasive manufacturer

More information

Telephone: Fax: Web site:

Telephone: Fax:   Web site: Street Design established in 1986 UK street furniture designers & manufacturers, Leicestershire LE12 8LD Contact us BEXLEY seating As UK based, designers and manufacturers, Street Design can manufacture

More information

Carbide lasts 150 times longer than sandpaper True Grit Performance with Carbide

Carbide lasts 150 times longer than sandpaper True Grit Performance with Carbide Carbide lasts 150 times longer than sandpaper True Grit Performance with Carbide Carbide is the strongest and most effective abrasive tool on the market today. Our highly versatile grinding products are

More information

Orbitor PILLING & SNAGGING TESTER

Orbitor PILLING & SNAGGING TESTER PRODUCT UPDATE Extraordinary Testing Solutions = Orbitor PILLING & SNAGGING TESTER A consistent and reliable way to test the pilling and snagging properties of woven and knitted fabrics. With the James

More information

How to Cut a Handlebar for Installation of PadLoc Grips. How to Cut a Handlebar for Installation of PadLoc Grips

How to Cut a Handlebar for Installation of PadLoc Grips. How to Cut a Handlebar for Installation of PadLoc Grips How to Cut a Handlebar for Installation of PadLoc Grips How to Cut a Handlebar for Installation of PadLoc Grips Tools required 8. 5. 6. 7. 9. 4. 3. 2. 1. Bars with PadLoc Markings 1. Park SG-7.2 Saw Guide

More information

Junior Trampoline With Handle

Junior Trampoline With Handle Junior Trampoline With Handle Model No: TRMI-0004 WARNING Read these instructions prior to assembling and using this trampoline - Warning - This trampoline is subject to a 35 kgs weight limit. Do not allow

More information

To prepare for your upcoming exam it s vitally important for you to revise key information and technical terminology for each subject discipline.

To prepare for your upcoming exam it s vitally important for you to revise key information and technical terminology for each subject discipline. To prepare for your upcoming exam it s vitally important for you to revise key information and technical terminology for each subject discipline. In the exam there will be some multiple choice questions

More information

CERTIFICATE OF ACCREDITATION

CERTIFICATE OF ACCREDITATION CERTIFICATE OF ACCREDITATION In terms of section 22(2) (b) of the Accreditation for Conformity Assessment, Calibration and Good Laboratory Practice Act, 2006 (Act 19 of 2006), read with sections 23(1),

More information

Woven interlinings and linings for apparel purposes Specification

Woven interlinings and linings for apparel purposes Specification KENYA STANDARD DKS 08-21: PART 2: 2017 ICS 59.080 Woven interlinings and linings for apparel purposes Specification Part 2: Woven linings for Apparel Purposes KEBS 2017 SECOND EDITION 2 TECHNICAL COMMITTEE

More information

precision. On a mission of New Compact Generation Always the right choice the Bosch Compact Generation. The new jigsaws from Bosch.

precision. On a mission of New Compact Generation Always the right choice the Bosch Compact Generation. The new jigsaws from Bosch. Always the right choice the Bosch Compact Generation. On a mission of precision. The new jigsaws from Bosch. Easy Expert Universal New Compact Generation Easy Universal Expert NEW! The Compact Generation

More information

Important Retain for future reference: Read carefully

Important Retain for future reference: Read carefully TOULOUSE Dresser Important Retain for future reference: Read carefully Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product. Your child

More information

UNIT 9b: SCREW FASTENERS Introduction Functions Screw Features Elements Terms of a Thread Profile

UNIT 9b: SCREW FASTENERS Introduction  Functions Screw Features Elements Terms of a Thread Profile UNIT 9b: SCREW FASTENERS Introduction A mechanical screw is a cylinder or cone that has a helical ridge called a thread. A helix has one or more turns, so a screw can have several turns. If the helix is

More information

vision Seating systems for demanding audiences The Vision Set has been awarded the Golden MTP 2006 Medal Project: Charaziak Design Studio

vision Seating systems for demanding audiences The Vision Set has been awarded the Golden MTP 2006 Medal Project: Charaziak Design Studio Seating systems for demanding audiences auditoria sports facilities all rights reserved Universal use, functionality and fine looks make the Vision seating system ideal for all kinds of facilities. Vision

More information

Self Laminating Wire and Cable Markers

Self Laminating Wire and Cable Markers SBP Self Laminating Wire and Cable Markers Technical Datasheet TTDS-211 Revision 12 - December 2018 SBP is a clear vinyl film with a white thermal transfer printable area. On application, the clear film

More information

Kent Airport Bump Rail

Kent Airport Bump Rail Kent Airport Bump Rail 1 KENT STAINLESS: SANITARY WARE Specify: Kent Airport Bump Rail (KABR50); Length:1200mm, 50mm Diameter, Thickness: 2mm; Grade 304 Stainless steel; Satin Finish 320 Grit Polish. Description:

More information

BuzziFrontDesk Product Specification Sheet

BuzziFrontDesk Product Specification Sheet BuzziFrontDesk Product Specification Sheet This document contains technical information about the BuzziFrontDesk www.buzzi.space Frontpanel for worktop This workspace divider safeguards your privacy at

More information

ISO INTERNATIONAL STANDARD. Rubber- or plastics-coated fabrics Determination of abrasion resistance Part 2: Martindale abrader

ISO INTERNATIONAL STANDARD. Rubber- or plastics-coated fabrics Determination of abrasion resistance Part 2: Martindale abrader INTERNATIONAL STANDARD ISO 5470-2 First edition 2003-04-15 Rubber- or plastics-coated fabrics Determination of abrasion resistance Part 2: Martindale abrader Supports textiles revêtus de caoutchouc ou

More information

OPERATOR S MANUAL DRILLING MACHINE WITH ELECTROMAGNETIC BASE

OPERATOR S MANUAL DRILLING MACHINE WITH ELECTROMAGNETIC BASE OPERATOR S MANUAL DRILLING MACHINE WITH ELECTROMAGNETIC BASE UNIT 30 NEWHALLHEY BUSINESS PARK, NEWHALLHEY RD, RAWTENSTALL, ROSSENDALE, LANCASHIRE BB4 6HR Tel. +44 1706 229490, fax. +44 1706 830496 www.jeiuk.com

More information

SEMPEO2-23 (SQA Unit Code - FP2Y 04) Producing platework components and assemblies

SEMPEO2-23 (SQA Unit Code - FP2Y 04) Producing platework components and assemblies Overview This standard covers a broad range of basic heavy platework (above 3 mm) competences that will prepare you for entry into the engineering or manufacturing sectors, creating a progression between

More information

TURNING TOOLS CARVING TOOLS

TURNING TOOLS CARVING TOOLS Multi Jig SVS-50 (37592) TURNING TOOLS Square and skew chisels with straight or curved edges. Max width 32 mm (1¼"). Parting tools Beading tools Roughing gouges Max width 50 mm (2"). CARVING TOOLS Gouges,

More information

VICTOGRAIN Simply better

VICTOGRAIN Simply better Simply better Innovation TRUST BLUE Triangular, precision-formed abrasive grain Fastest work progress Longest tool life General information VICTOGRAIN products are some of the most effective grinding tools

More information

SBP Self Laminating Wire and Cable Markers

SBP Self Laminating Wire and Cable Markers SBP Self Laminating Wire and Cable Markers Technical Datasheet TTDS-211 Revision 10 - April 2018 SBP is a clear vinyl film with a white thermal transfer printable area. On application, the clear film over-laminates

More information

Code Desc. Ø mm Ø hole mm. Code Desc. Ø mm Ø hole mm. With wire of corrugated steel. Suitable for removing rust, scale etc.. Employee of grinders.

Code Desc. Ø mm Ø hole mm. Code Desc. Ø mm Ø hole mm. With wire of corrugated steel. Suitable for removing rust, scale etc.. Employee of grinders. Circular brush steel wire Corrugated steel wire high strength. Suitable for deburring, satin finishing and polishing, to remove rust and metal cleaning. Code Desc. Ø Ø hole Thickness 3002700 77-150x16

More information

application manual >> ductwork

application manual >> ductwork application manual >> DUCTWORK application manual >> ductwork APPLICATION MANUAL DUCTWORK application manual >> ductwork 1 THERMAL INSULATION OF DUCTWORK 3» Measure surface dimension for insulating rectangular

More information