DESCRIPTION 3. DIE INSTALLATION AND REMOVAL Die Removal (Figure 3) 3.1. Die Installation (Figure 3) Hydraulic Hand Tool

Size: px
Start display at page:

Download "DESCRIPTION 3. DIE INSTALLATION AND REMOVAL Die Removal (Figure 3) 3.1. Die Installation (Figure 3) Hydraulic Hand Tool"

Transcription

1 Crimping Dies Instruction Sheet for SOLISTRAND* s and Splices 9 APR PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended use, production operations is available. Crimping Dies for SOLISTRAND s and Splices Indenter NOTE: Figures and illustrations are for reference only, and are not drawn to scale. DIES NOMINAL WIRE SIZE TYPICAL NEST INDENTER MM AWG PRODUCT 90 G G / RTTz 90 9D 90 D 90 G G 90 0D 90 D 90 G G 90 D 90 D 90 G G 90 D 90 D 90 G G 90 D 90 D / RTTz / BS[ 87 / PSY 9 60 /0 696 / PSY /0 698 / PSY /0 697 / RTTz /0 69 / RTTz Nest MM [CIRCULAR MIL AREA RANGE] [ ] [ ] TOOL OR HEAD NUMBER Head Number [ ] 9080, 908, [ ] Hydraulic Hand Tool Number 9078, [ ] [ ] [ ] [ ] GAlso used for STRATO THERM* Heat Resistant Uninsulated s zrtt=ring Tongue s [BS=Butt Splice YPS=Parallel Splice DDies for Heavy Duty s +90 Bend s Figure. INTRODUCTION This instruction sheet provides application instructions, maintenance, and inspection procedures for the dies listed in Figure. These dies crimp SOLISTRAND ring tongue terminals, butt splices, and parallel splices to solid or stranded copper wire (also listedinfigure). The dies are used in Hydraulic Heads 9080, 908, 907, and Hydraulic Hand Tools 9078 and Refer to Figure and Figure. E0 Tyco Electronics Corporation, a TE Connectivity Ltd. Company All Rights Reserved *Trademark TOOLING ASSISTANCE CENTER PRODUCT INFORMATION This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. of 7 LOC B

2 Tools Using Crimping Dies for SOLISTRAND s and Splices (Refer to Figure ) Hydraulic Hand Tool 9079 Hydraulic Hand Tool 9078 CAUTION electrical lines. Hydraulic Head 9077 Hydraulic Head 908 Hydraulic Head 9080 WARNING Figure NOTE i All dimensions on this document are in metric units [with U. S. customary units in brackets]. Figures and illustrations are for reference only and are not drawn to scale. Reason for revision is given in Section 7, REVISION SUMMARY.. DESCRIPTION Each die assembly consists of a nest and an indenter (ordered separately) which are retained in the crimping head by retainer pins. The nest is positioned in the yoke of the crimping head, and the indenter is positioned in the ram of the tool.. DIE INSTALLATION AND REMOVAL Refer to Figure and determine the correct die assembly, wire size, product number, and tool head to be used together. CAUTION! Never operate the tool with the dies removed... Die Installation (Figure ) DANGER To avoid personal injury, be sure to exercise extreme caution when using the power unit. Avoid depressing the footswitch or trigger control when installing or removing dies.. Depress the upper die release button located in the C head.. Slide the nest into place in C head. See Figure.. Release the button and rock the die back and forth until the nest snaps into position.. Activate the power unit until the lower die release button located in the ram is exposed.. Depress the release button. 6. Slide the indenter into position in the ram. See Figure. 7. Release the button and rock the indenter back and forth until the die snaps into position. 8. Return ram to the down position... Die Removal (Figure ). Depress the upper release button located in the C head and slide the nest out of the head.. Activate the power unit until the lower die release button (located in the ram) is exposed.. Depress the die release button and slide the indenter out of the ram. of 7

3 Nest Die Release Button Indenter Die Release Button Ram (Advanced) Figure. WIRE STRIPPING AND CRIMPING PROCEDURES.. Wire Stripping Strip wire to the dimensions listed in Figure. Do NOT nick or cut the wire strands... Crimping Procedure DANGER To avoid personal injury, be sure to exercise caution while holding terminals, splices or wire near the crimping area of power units.. Ensure that the wire range or size stamped on the terminal or splice corresponds with the wire size being used and the wire range or size stamped on the nest and indenter.. Center terminal or splice in nest as shown in Figure. For best results, when brazed seam on terminal or splice is visible, position seam toward indenter.. Activate power unit so that ram advances and holds terminal or splice in place. Do NOT deform terminal or splice wire barrel.. Insert stripped wire into terminal or parallel splice until end of conductor is flush with or extended slightly beyond end of wire barrel.. Insert stripped wire into butt splice until end of conductor butts against splice wire stop. 6. Activate power unit to complete the crimp. NOTE i If terminal sticks in die after crimping, grasp wire close to crimp and apply a rocking motion to remove from die. 7. For butt splice, repeat steps and 6 for other wire barrel. 8. Refer to Paragraph., Crimp Inspection, for standard terminal, butt splice, and parallel splice crimp inspection.. INSPECTION/MAINTENANCE DANGER To avoid personal injury, disconnect the power supply before performing maintenance, adjustments, inspections and repairs... Crimp Inspection (Figure 6) NOTE i The accompanying procedure is included as an aid to the tool operator ONLY. It is not intended to serve as a quality control procedure for qualifying finished crimps on SOLISTRAND terminals or splices. Inspect crimped terminals or splices by checking the features described in Figure 6. Use only terminals or splices that meet the conditions shown in the ACCEPT column. s and splices displaying the features shown in the REJECT column can be avoided by careful use of these instructions and by performing the maintenance and inspection procedures described in Paragraphs in. and.... Daily Maintenance It is recommended that each operator of the dies be made aware of, and responsible for, the following steps of daily maintenance:. Remove dust, moisture, and other contaminants from the dies with a clean brush, or a clean, soft, lintfree cloth. Do NOT use objects that could damage the dies.. If dies are coated with oil or preservative, wipe clean particularly in the crimping areas before placing them in use. of 7

4 Butt Splice Parallel Splice B B B B Equals Wire Barrel NOMINAL WIRE SIZE mm RING TONGUE TERMINALS STRIP LENGTHS BUTT SPLICES PARALLEL SPLICES mm AWG CMA RANGE MIN MAX MIN MAX MIN MAX / / /0 00 / [, ] [0,800,00] [,00,600] 6.6. [,600 8,700]. 60. [8,700 9,00] [9,00 0,00] [0,00 90,000] [90,000,000] 8. [0.8] 9.9 [0.9].09 [0.].096 [0.6] 9.8 [0.9]. [0.].0 [0.8].890 [0.7] 0.9 [0.06].906 [0.69].9 [0.].08 [0.9]. [0.7].700 [0.0].88 [0.6].87 [0.6] 0.9 [0.06]. [0.7].9 [0.].08 [0.9]. [0.7].906 [0.69].88 [0.6].87 [0.6] [0.7] [0.797] [0.6] [0.687] [0.687] [0.776] 0.67 [0.8] 0.67 [0.8] Figure 7.6 [0.687] 7.6 [0.687] [0.687] [0.8] Butt Splice Inspection Holes of or Butt Splice Must Face Either Die End of Wire Visible Through Inspection Hole Brazed Seam (Typ) Parallel Splice Ends of Wires Flush with or Extended Beyond End of Barrel or Splice Centered in Nest Figure of 7

5 ACCEPT REJECT Stamped Under Tongue Stamped Under Tongue Sight Hole or Standard Type Parallel Splice 6 Butt Splice Stamped Here Crimps centered. Crimps may be off center BUT NOT OFF END OF WIRE BARREL. Strap Type AWG wire size being used matches wire range or size stamped on terminal or splice and dies. Insulation does not enter wire barrel. Wire is visible through inspection hole of butt splices. Wire is flush with or extends slightly beyond end of terminal wire barrel. On parallel splices, bare wire ends must be flush with or extended slightly beyond end of barrel. Stamped Here Crimped off end of splice or terminal wire barrel. AWG wire size being used does not match wire size or range stamped on terminal or splice and dies. Insulation entered barrel of terminal or splice. CHECK FOR INCORRECT STRIP LENGTH. Wire not inserted far enough in terminal or splice. End of wire must be visible through inspection hole of butt splices, and be flush with or extend slightly beyond end of terminal wire barrel or parallel splice. Excessive flash on terminal or splice indicates damaged dies or wrong wire, splice, or tooling combination was used. 6 Nicked or missing strands. Figure 6. When dies are not in use, make certain all surfaces are protected with a THIN coat of any good SAE 0 motor oil, and mate and store them in a clean, dry area... Periodic Inspection Regular inspections should be performed by quality control personnel. A record of scheduled inspections should remain with the dies or be made available to supervisory personnel responsible for the dies. Though recommendations call for at least a monthly inspection, the inspection frequency should be based upon the amount of use, working conditions, operator training and skill, and established company standards. These inspections should be performed in the following sequence: A. Visual Inspection (Figure 7). Remove all lubrication and accumulated film by immersing the dies in a suitable degreaser that will not affect paint or plastic.. Check all surfaces for wear. Inspect the crimp area for flattened, chipped, cracked, worn, or broken areas. If damage is evident, the die must be replaced. of 7

6 Pitted Flattened Broken. Align the GO element with the wire barrel crimping chamber. Push the element straight into the the crimping chamber without using force. The GO element must pass completely through the crimping chamber. Chipped. Align the NOGO element and try to insert it straight into the same crimping chamber. The NOGO element may start entry but must not pass completely through. If the crimping chamber conforms to the gage inspection, the dies are considered dimensionally correct. If not, they must be replaced. For additional information regarding the use of a plug gage, refer to Instruction Sheet REPLACEMENT PARTS Figure 7 B. Gaging the Crimping Chamber (Figures 8 and 9) The inspection requires the use of a plug gage conforming to the dimensions in Figure 9. TE Connectivity does not manufacture or market these gages. Proceed as follows:. Mate the dies until it is evident that they have bottomed. Hold the dies in this position. When replacement of a die becomes necessary, contact your local TE Representative; call 8006; send a facsimile of your purchase order to ; or write to: CUSTOMER SERVICE (8) TYCO ELECTRONICS CORPORATION P. O. BOX 608 HARRISBURG, PA REVISION SUMMARY S Updated document to corporate requirements. Dies Bottomed But Not Under Pressure GO Element Must Pass Completely Through the Die Closure. Figure 8 NO GO Element May Enter Partially, But Must Not Pass Completely Through the Die Closure. 6 of 7

7 SUGGESTED PLUG GAGE DESIGN Die Closure Configuration B GO Dim. C Dim. Typ B NO GO Dim. A Dim. R 0.80 [.000] Typ R DIES DIE CLOSURE DIMENSION A GAGE ELEMENT DIMENSIONS B NEST INDENTER GO NO GO GO NO GO [.000].69 [.060]..8 [ ] [ ] C DIMENSION 7.9 [.] RADIUS R [.0] [.60] [.0.] [.69.60] [.7] [.7] [.80] [.90] [.80.8] [.99.90] [.7] [.8] [.0] [.0] [.0.] [.09.0] [.7] [.0] [.] [.0] [.0] [.0.] [.09.0] [.7] [.96] [.70] [.80] [.70.7] [.89.80] [.6] [.8] 7.8 [.080] [.60] 8.06 [.60] 8.99 [.0] Figure [ ] [.60.6] [.9.60] [.9.0] 9..7 [.7] [.6] 0.69 [.] 7 of 7

Crimping Dies for SOLISTRAND* Terminals and Splices

Crimping Dies for SOLISTRAND* Terminals and Splices ORIGINAL INSTRUCTIONS Crimping Dies for SOLISTRAND* Terminals and Splices Instruction Sheet 408-8691 02 AUG 18 Rev H1 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use

More information

Terminals and Splices 19 OCT 11 Rev D. Crimping Dies for Head Numbers 69065, 69067, and Hand Tool Yoke. Place Screwdriver Here to Remove Dies

Terminals and Splices 19 OCT 11 Rev D. Crimping Dies for Head Numbers 69065, 69067, and Hand Tool Yoke. Place Screwdriver Here to Remove Dies Instruction Sheet Crimping Dies for SOLISTRAND* 408-9786 Terminals and Splices 19 OCT 11 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.

More information

SOLISTRAND* Flag Terminal Crimping Dies

SOLISTRAND* Flag Terminal Crimping Dies SOLISTRAND* Flag Terminal Crimping Dies Instruction Sheet 408-8908 22 DEC 10 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools

More information

Terminal and Splice , , and JUN 12 Rev D NOTE. CERTI-CRIMP* Hand Crimping Tool Ratchet Control CAUTION NOTE

Terminal and Splice , , and JUN 12 Rev D NOTE. CERTI-CRIMP* Hand Crimping Tool Ratchet Control CAUTION NOTE Terminal and Splice Instruction Sheet Crimping Tools 408-1254 69339, 69354-1, and 69355 11 JUN 12 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered

More information

SOLISTRAND* Crimping Dies

SOLISTRAND* Crimping Dies SOLISTRAND* Crimping Dies Instruction Sheet (Used in Crimping Heads 08-697 69097 and 69099) 5 APR Terminals Butt Splices Parallel Splices = Wire Barrel DIE SET NUMBERS FOR DIE SET CRIMPING HEAD 69097 NUMBERS

More information

Crimping Dies for TERMINYL* and PLASTI-GRIP* Terminals and Splices

Crimping Dies for TERMINYL* and PLASTI-GRIP* Terminals and Splices Crimping Dies for TERMINYL* and PLASTI-GRIP* Terminals and Splices Instruction Sheet 408-10051 11 APR 17 Rev D PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually

More information

Crimping Dies; PN thru 47825, 47915, and 47918

Crimping Dies; PN thru 47825, 47915, and 47918 Crimping Dies; PN 47820 thru 47825, 47915, and 47918 Instruction Sheet 408-1729 22 NOV 16 Rev K Crimping Dies; PN 47820 thru 47825, 47915, and 47918 (Typical) Crimping Die Wire Size Part Number Color Code

More information

1. Actuate the upper die release button located in the C head or closed head. 2. Slide the nest into place in C head or closed head. See Figure 2.

1. Actuate the upper die release button located in the C head or closed head. 2. Slide the nest into place in C head or closed head. See Figure 2. The die assemblies consist of stationary dies (nests) and moving dies (anvils). The dies are retained in the crimp tool by retainer pins. Refer to the table in Figure 3 to ensure the compatibility of die

More information

OCT 14 Rev K

OCT 14 Rev K ORIGINAL INSTRUCTIONS Hand Crimping Tool 68026 for TERMI-FOIL* Product Instruction Sheet 408-2363 27 OCT 14 Rev K PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of

More information

Hydraulic Hand Crimping Tool, PN

Hydraulic Hand Crimping Tool, PN ORIGINAL INSTRUCTIONS Hydraulic Hand Crimping Tool, PN 59975-1 Instruction Sheet 408-6758 21 JUN 17 Rev F PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually

More information

This instruction sheet covers the application and maintenance procedures for Crimping Die Assembly

This instruction sheet covers the application and maintenance procedures for Crimping Die Assembly Figure 1 This instruction sheet covers the application and maintenance procedures for Crimping Die Assembly 318106 1. For additional information on COPALUM terminals and splices, refer to Catalog 82020.

More information

Crimping Die Assemblies , , , , , , , , and 69653

Crimping Die Assemblies , , , , , , , , and 69653 Crimping Die Assemblies 46754-2, 46755-2, 46756-2, 46757-2, 46758-2, 46759-2, 46760-2, 59870-1, and 69653 Instruction Sheet 408-1602 10 NOV 16 Rev C 1. INTRODUCTION WIRE SIZE (MCM) (1) CMA (Circular Mil

More information

Refer to Figure 2 and select the appropriate wire, die assembly, and terminal or splice. Strip the wire to the length indicated in the table.

Refer to Figure 2 and select the appropriate wire, die assembly, and terminal or splice. Strip the wire to the length indicated in the table. The die assemblies consist of stationary dies (nests) and moving dies (anvils). Refer to Figure 2 to ensure the compatibility of die assemblies, crimping heads, and terminals and splices. The shanks on

More information

Hand Crimping Tools , , and AUG 12 Rev D

Hand Crimping Tools , , and AUG 12 Rev D Instruction Sheet 408-7332 Hand Tools 90123-2, 90123-5, and 90124-2 29 AUG 12 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools

More information

instructions packaged with the tools or contact the Tooling Assistance Center number at the bottom of this page.

instructions packaged with the tools or contact the Tooling Assistance Center number at the bottom of this page. This instruction sheet provides instructions on product application, and maintenance and inspection procedures for SOLISTRAND Crimping Dies which are used in Crimping Heads 69097 and 69099. See Figure

More information

FEB 18 Rev D

FEB 18 Rev D ORIGINAL INSTRUCTIONS Terminal and Splice Crimping Die Assemblies Instruction Sheet 408-1632 01 FEB 18 Rev D PROPER USE GUIDELINES Cumulative trauma disorders can result from the prolonged use of manually

More information

APR 15 Rev A

APR 15 Rev A ORIGINAL INSTRUCTIONS CERTI-CRIMP* Hand Tools 47386-4, 47387-7, and 525690-1 Instruction Sheet 411-1050 24 APR 15 Rev A PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use

More information

2. Remove assembly pins from mounting lugs as. shown in Figure 1.

2. Remove assembly pins from mounting lugs as. shown in Figure 1. This instruction sheet provides instructions on product application and Maintenance and Inspection for Insulation Piercing COPALUM Terminal and Splice Crimping Heads (68081 and 68082) used in Pneumatic

More information

PRO- CRIMPER* III Hand Crimping

PRO- CRIMPER* III Hand Crimping PRO- CRIMPER* III Hand Crimping Instruction Sheet Tool Assembly 58448-2 408-9357 With Die Assembly 58448-3 10 Mar 11 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use

More information

AUG 15 Rev M

AUG 15 Rev M ORIGINAL INSTRUCTIONS PRO-CRIMPER III Hand Crimping Tool Assembly 58433-3 with Die Assembly 58423-1 Instruction Sheet 408-9252 21 AUG 15 Rev M PROPER USE GUIDELINES Cumulative Trauma Disorders can result

More information

High Current Pin and Socket Contacts 31 JUL 13 Rev C

High Current Pin and Socket Contacts 31 JUL 13 Rev C Application Specification High Current Pin and Socket Contacts 31 JUL 13 NOTE NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and

More information

Instruction Sheet 2 mm Common Termination (CT) Head Assembly

Instruction Sheet 2 mm Common Termination (CT) Head Assembly Instruction Sheet 2 mm Common Termination (CT) 408-9426 Head Assembly 58372-1 05 MAY 14 Wire Inserter (Shown In Up Position) Carriage Drag Wire Guide Feed Pawl (Portion of Head Assembly Shown Cut Away

More information

A socket contact support (supplied separately) must be installed onto the locator assembly.

A socket contact support (supplied separately) must be installed onto the locator assembly. Figure 1 PRO CRIMPER III Hand Tool Assembly 1976444 1 consists of PRO CRIMPER III Hand Tool Frame 354940 1 and Die Assembly 1976444 2. The tool assembly is used to crimp the contacts listed in Figure 1.

More information

JUL 15 Rev E

JUL 15 Rev E ORIGINAL INSTRUCTIONS SDE PEW-12 Hand Crimping Tool Assembly 2031734-1 with Die Assembly 2031734-2 Instruction Sheet 408-10243 02 JUL 15 Rev E PROPER USE GUIDELINES Cumulative Trauma Disorders can result

More information

onlinecomponents.com

onlinecomponents.com Figure 1 PRO CRIMPER III Hand Crimping Tool Assembly 58603 1 consists of Die Assembly 58603 2 and PRO CRIMPER III Hand Tool Frame 354940 1. The die assembly consists of crimping dies and a locator assembly.

More information

Read these instructions thoroughly before crimping any contacts.

Read these instructions thoroughly before crimping any contacts. PRO CRIMPER III Hand Crimping Tool Assembly 58583 1 consists of Die Assembly 58583 2 and PRO CRIMPER III Hand Crimping Tool Frame 354940 1. The die assembly consists of crimping dies and a locator assembly.

More information

Hand Crimping Tool [ ]

Hand Crimping Tool [ ] 408-8738 Revision T, Jan. 2017 PRO-CRIMPER III Hand Crimping Tool 790163-[ ] 1. Introduction PRO-CRIMPER III Hand Crimping Tool Assembly 790163-[ ] consists of PRO-CRIMPER III Hand Tool Frame 354940-1

More information

Cluster Block Housings and Contacts

Cluster Block Housings and Contacts Cluster Block Housings and Contacts Application Specification 114-2019 20 SEP 17 Rev J NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters

More information

Instruction Sheet Tool Kit [ ] (for SL Series 110 Jack Connectors)

Instruction Sheet Tool Kit [ ] (for SL Series 110 Jack Connectors) Instruction Sheet Tool Kit 1725150 [ ] (for SL Series 110 Jack Connectors) 26 FEB 04 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.

More information

Housings and Contacts 20 JUL 11 Rev G

Housings and Contacts 20 JUL 11 Rev G Application Specification Cluster Block 114-2019 Housings and Contacts 20 JUL 11 NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and

More information

DEUTSCH Instructional Manual for HDP-400 Power Crimper (TE CONNECTIVITY PN )

DEUTSCH Instructional Manual for HDP-400 Power Crimper (TE CONNECTIVITY PN ) ORIGINAL INSTRUCTIONS DEUTSCH Instructional Manual for HDP-400 Power Crimper (TE CONNECTIVITY PN 1606312-1) Instruction Sheet 0425-034-0000 15 JAN 18 Rev H NOTE All numerical values are in metric units

More information

Checking Terminal Crimp Height or Gaging the Die Closure

Checking Terminal Crimp Height or Gaging the Die Closure Checking Terminal Crimp Height or Gaging the Die Closure Instruction Sheet 408-7424 27 MAR 18 Rev S 1. INTRODUCTION Crimp height comparators and plug gages are instruments recommended for verifying the

More information

VS- 3 Hand Tool Kits , , and

VS- 3 Hand Tool Kits , , and VS- 3 Hand Tool Kits 244271-1, 244271-5, and 244271-6 Instruction Sheet 408-7280 Jan 2017 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools.

More information

AMPSEAL* Automotive Plug Connector and Header Assembly

AMPSEAL* Automotive Plug Connector and Header Assembly AMPSEAL* Automotive Plug Connector and Header Assembly Application Specification 114-16016 17 APR 14 NOTE NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Unless

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet Modular Crimp Head Order No. 63811-5970 FEATURES Application Tooling Specification Sheet TYPE 4A Hand Crimp Tool Order No. 63811-5900 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet Tool Kit Order No. 63823-6470 FEATURES Application Tooling Specification Sheet Hand Crimp Tool Order No. 63823-6400 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed

More information

1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward.

1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward. Figure 1 Miniature Quick Change Applicators, of the end feed type, are designed to crimp end feed strip terminals to prestripped wires. Each applicator is set up to accept the strip form of certain specific

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL FEATURES Application Tooling Specification Sheet TYPE 7 Order No. 63811-9200 A full cycle ratcheting hand tool ensures complete crimps A precision user-friendly terminal locator wire stop

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet Tool Kit Order No. 63811-5370 FEATURES Application Tooling Specification Sheet TYPE 4C Hand Crimp Tool Order No. 63811-5300 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed

More information

MAG-MATE* Series 300 Terminals

MAG-MATE* Series 300 Terminals MAG-MATE* Series 300 Terminals Application Specification 114-2046 28 NOV 18 Rev AB All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches].

More information

HOLLINGSWORTH Operating Instructions

HOLLINGSWORTH Operating Instructions HOLLINGSWORTH Operating Instructions H20 - Rotary Nest Hand Crimping Tool HOLLINGSWORTH (800) 638-8376 techsuppt@hollingsworth.com www.hollingsworth.com OPERATING INSTRUCTIONS FOR HOLLINGSWORTH H20 ROTARY

More information

OCT 15 Rev E

OCT 15 Rev E ORIGINAL INSTRUCTIONS Coaxial Cable Stripper Kits 603995-[ ] Instruction Sheet 408-2766 09 OCT 15 Rev E PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered

More information

JUL 14 Rev C

JUL 14 Rev C Wire-to-Wire Insulation Displacement Contact (IDC) CoolSplice* Connector Application Specification 114-19136 03 JUL 14 Rev C All numerical values are in metric units [with U.S. customary units in brackets].

More information

Solder Tine Terminal Crimp Wire Terminal. Retention Barb Carrier Strip. Wire Lead-In. Slotted Beams Housing (Customer Supplied) Figure 1

Solder Tine Terminal Crimp Wire Terminal. Retention Barb Carrier Strip. Wire Lead-In. Slotted Beams Housing (Customer Supplied) Figure 1 MAG-MATE* Series 187 Terminals Application Specification 114-2069 28 NOV 18 Rev E All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches].

More information

HAND CRIMP TOOL SPECIFICATION SHEET Order No (Replaces (HTR1031E) And (HTR1031E1))

HAND CRIMP TOOL SPECIFICATION SHEET Order No (Replaces (HTR1031E) And (HTR1031E1)) HAND CRIMP TOOL SPECIFICATION SHEET Order No. 63811-3200 (Replaces 11-01-0084 (HTR1031E) And 11-01-0211 (HTR1031E1)) TYPE 2C SCOPE Terminal Wire Size Insulation Diameter Strip Length AWG mm² mm In. mm

More information

Application Tooling Specification

Application Tooling Specification Order No. 63828-2000 Application Tooling Specification Type 4G FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomically designed soft handles Precisely designed crimping profiles

More information

PALO VERDE NUCLEAR GENERATING STATION

PALO VERDE NUCLEAR GENERATING STATION PALO VERDE NUCLEAR GENERATING STATION Electrical Maintenance Training Program Classroom Lesson Electrical Maintenance Training Program Date: 09/01/2011 2:50:31 PM LP Number: NEA04L00103 Rev Author: MARK

More information

NOV 16 Rev L

NOV 16 Rev L Terminating Modules 856196-[ ] for Use with Modular Plug Dual Terminators 1320840-[ ] Instruction Sheet 408-9743 17 NOV 16 Rev L Modular Plug Dual Terminator Automatic Circuit Tester (Terminators 1320840-1

More information

Product Specification provides test and performance results for insulated terminals and splices for Class 1 E Nuclear applications.

Product Specification provides test and performance results for insulated terminals and splices for Class 1 E Nuclear applications. This specification covers the requirements for application of PIDG terminals, splices, and end caps in various operating environments. Each consists of a precision formed metal wire barrel and a copper

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet Tool Kit Order No. 63811-7370 FEATURES Application Tooling Specification Sheet TYPE 4C Hand Crimp Tool Order No. 63811-7300 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet Modular Crimp Head Order No. 63819-4670 FEATURES Application Tooling Specification Sheet TYPE 4A Hand Crimp Tool Order No. 63819-4600 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically

More information

Hand Crimp Tool Specification Sheet Order No

Hand Crimp Tool Specification Sheet Order No Hand Crimp Tool Specification Sheet Order No. 63811-7400 FEATURES ΠA full cycle ratcheting hand tool ensures complete crimps ΠErgonomic soft grip handles for comfortable crimping ΠA precision user-friendly

More information

Screw Hole. Figure 1 TOOLING ASSISTANCE CENTER PRODUCT INFORMATION

Screw Hole. Figure 1 TOOLING ASSISTANCE CENTER PRODUCT INFORMATION Application Specification Solderless Light Emitting Diode (LED) 114-32038 Socket (Type LK) 07 SEP 12 NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions

More information

Miniature Circular Plastic Connector (CPC)

Miniature Circular Plastic Connector (CPC) Miniature Circular Plastic Connector (CPC) Application Specification 16 SEP 03 Rev O All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and

More information

HAND CRIMP TOOL SPECIFICATION SHEET Order No

HAND CRIMP TOOL SPECIFICATION SHEET Order No HAND CRIMP TOOL SPECIFICATION SHEET Order No. 63811-5500 FEATURES TYPE 4C ΠA full cycle ratcheting hand tool ensures complete crimps ΠErgonomic soft grip handles for comfortable crimping ΠA precision

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet Hand Crimp Tool FEATURES Application Tooling Specification Sheet Order No. 200218-2300 % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed soft handles % Precisely designed

More information

SCOPE Perma-Seal Terminals and Splices AWG (Rings, Spades, Hooks, 3 and 4-Ways, and Splices). RHT-5770 Hand Crimp Tool

SCOPE Perma-Seal Terminals and Splices AWG (Rings, Spades, Hooks, 3 and 4-Ways, and Splices). RHT-5770 Hand Crimp Tool Hand Crimp Tool Operating Instruction Sheet and Specifications Part No. 64001-3200 Eng. No. RHT 5770 (Replaces 19285-0050 and 19285-0143) FEATURES A full cycle ratcheting hand tool ensures complete crimps

More information

HAND CRIMP TOOL SPECIFICATION SHEET Order No

HAND CRIMP TOOL SPECIFICATION SHEET Order No HAND CRIMP TOOL SPECIFICATION SHEET Order No. 63811-9200 FEATURES TYPE 7 A full cycle ratcheting hand tool ensures complete crimps A precision user-friendly terminal locator wire stop holds terminals in

More information

Order Number

Order Number Order Number 200218-5500 FEATURES Application Tooling Specification TYPE 4D A full-cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly

More information

COPALUM Terminals and Splices (For Solid & Stranded Aluminum or Copper Wire)

COPALUM Terminals and Splices (For Solid & Stranded Aluminum or Copper Wire) Product Facts Bar Crimp Technique Terminals and Splices for aluminum-to-aluminum and aluminum-to-copper stripped wire applications Terminates stripped, stranded and solid (round or rectangular) aluminum

More information

HAND CRIMP TOOL SPECIFICATION SHEET Order No

HAND CRIMP TOOL SPECIFICATION SHEET Order No HAND CRIMP TOOL SPECIFICATION SHEET Order No. 63811-5200 TYPE 2C FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly

More information

Hand Crimp Tool Operating Instruction and Specifications Sheet Part No Eng. No. RHT 5770 (Replaces and )

Hand Crimp Tool Operating Instruction and Specifications Sheet Part No Eng. No. RHT 5770 (Replaces and ) Hand Crimp Tool Operating Instruction and Specifications Sheet Part No. 64001-3200 Eng. No. RHT 5770 (Replaces 19285-0050 and 19285-0143) FEATURES ΠA full cycle ratcheting hand tool ensures complete crimps

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63819-0400 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63828-0200 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

HAND CRIMP TOOL SPECIFICATION SHEET Order No

HAND CRIMP TOOL SPECIFICATION SHEET Order No HAND CRIMP TOOL SPECIFICATION SHEET Order No. 63811-7200 FEATURES TYPE 4C ΠA full cycle ratcheting hand tool ensures complete crimps ΠErgonomic soft grip handles for comfortable crimping ΠA precision

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63825-8100 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

CEELOK FAS-T* High-Speed Circular Connector System

CEELOK FAS-T* High-Speed Circular Connector System CEELOK FAS-T* High-Speed Circular Connector System Application Specification 114-32025 02 APR 12 NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are

More information

Application Tooling Specification

Application Tooling Specification Order No. 63828-1200 Application Tooling Specification Type 4D FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision, user-friendly

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL FEATURES Application Tooling Specification Sheet TYPE 4D Order No. 63811-8700 A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Hand Crimp Tool Specification Sheet Order No Replaces (HTR1031E) And (HTR1031E1)

Hand Crimp Tool Specification Sheet Order No Replaces (HTR1031E) And (HTR1031E1) Hand Crimp Tool Specification Sheet Order No. 63811-3200 Replaces 11-01-0084 (HTR1031E) And 11-01-0211 (HTR1031E1) TYPE 2C FEATURES ΠΠΠΠA full cycle ratcheting hand tool ensures complete crimps Ergonomic

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL FEATURES Application Tooling Specification Sheet TYPE 4D Order No. 63819-0300 A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL FEATURES Application Tooling Specification Sheet TYPE 4D Order No. 63827-1400 A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Hand Crimp Tool Operating Instruction And Specifications Sheet Order No Eng. No. RHT 7050 (Replaces )

Hand Crimp Tool Operating Instruction And Specifications Sheet Order No Eng. No. RHT 7050 (Replaces ) RHT7050 Hand Crimp Tool Hand Crimp Tool Operating Instruction And Specifications Sheet Order No. 64001-0900 Eng. No. RHT 7050 (Replaces 19285-0053) FEATURES ΠΠΠA full cycle ratcheting hand tool ensures

More information

HOLLINGSWORTH Operating Instructions

HOLLINGSWORTH Operating Instructions HOLLINGSWORTH Operating Instructions H20 - Rotary Nest Hand Crimping Tool HOLLINGSWORTH (800) 638-8376 techsuppt@hollingsworth.com www.hollingsworth.com H20 Tool - Tool Warranty TOOL WARRANTY Electro-Term/Hollingsworth

More information

Application Tooling Specification

Application Tooling Specification Order No. 63819-0901 Application Tooling Specification Type 4D FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision, user-friendly

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63819-0000 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Order Number

Order Number Order Number 200218-5900 FEATURES Application Tooling Specification TYPE 4D A full-cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63827-7500 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

HAND CRIMP TOOL Operating Instruction and Specification Sheet Order No (CR6115B)

HAND CRIMP TOOL Operating Instruction and Specification Sheet Order No (CR6115B) HAND CRIMP TOOL Operating Instruction and Specification Sheet Order No. 11-01-0203 (CR6115B) FEATURES Small handle spread which make this style tool ideally suited for end users Ratchet with safety release

More information

HAND CRIMP TOOL Operating Instruction and Specification Sheet Order No (CR60622B)

HAND CRIMP TOOL Operating Instruction and Specification Sheet Order No (CR60622B) HAND CRIMP TOOL Operating Instruction and Specification Sheet Order No. 11-01-0197 (CR60622B) FEATURES Small handle spread which make this style tool ideally suited for end users Ratchet with safety release

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63819-0900 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

HAND CRIMP TOOL Specification Sheet Order No

HAND CRIMP TOOL Specification Sheet Order No HAND CRIMP TOOL Specification Sheet Order No. 63811-8200 FEATURES TYPE 4D A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly

More information

Hand Crimp Tool Specification Sheet Order No

Hand Crimp Tool Specification Sheet Order No Hand Crimp Tool Specification Sheet Order No. 63811-2600 FEATURES TYPE 4A % A full cycle ratcheting hand tool ensures complete crimps % Ergonomically designed soft handles % Precisely designed crimping

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet Hand Crimp Tool Application Tooling Specification Sheet TYPE 4D Order No. 63819-0800 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Application Tooling Specification

Application Tooling Specification Order No. 200218-2200 Application Tooling Specification Type 4D FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision, user-friendly

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet Hand Crimp Tool Application Tooling Specification Sheet TYPE 4D Order No. 63819-1300 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63825-8200 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL FEATURES Application Tooling Specification Sheet TYPE 4D Order No. 200218-2400 A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

HAND CRIMP TOOL Specification Sheet Order No

HAND CRIMP TOOL Specification Sheet Order No HAND CRIMP TOOL Specification Sheet Order No. 63819-4400 FEATURES TYPE 4D A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL FEATURES Application Tooling Specification Sheet TYPE 4D Order No. 200218-1700 A full-cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63827-1500 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63819-1000 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

Excellent Integrated System Limited

Excellent Integrated System Limited Excellent Integrated System Limited Stocking Distributor Click to view price, real time Inventory, Delivery & Lifecycle Information: Molex Connector Corporation 0640014600 For any questions, you can email

More information

Hand Crimp Tool Operating Instruction Sheet And Specifications Part No Eng. No. RHT 1752 (Replaces )

Hand Crimp Tool Operating Instruction Sheet And Specifications Part No Eng. No. RHT 1752 (Replaces ) FEATURES Hand Crimp Tool Operating Instruction Sheet And Specifications Part No. 64003-1200 Eng. No. RHT 1752 (Replaces 19284-0011) ΠΠΠA full cycle ratcheting hand tool ensures complete crimps Long

More information

HAND CRIMP TOOL Operating Instruction and Specification Sheet Order No

HAND CRIMP TOOL Operating Instruction and Specification Sheet Order No FEATURES HAND CRIMP TOOL Operating Instruction and Specification Sheet Order No. 63811-2200 Small handle spread which make this style tool ideally suited for end users Ratchet with safety release that

More information

Application Tooling Specification Sheet

Application Tooling Specification Sheet HAND CRIMP TOOL Application Tooling Specification Sheet TYPE 4D Order No. 63819-0900 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping

More information

SIAMEZE* Standard and Fine Range Terminals

SIAMEZE* Standard and Fine Range Terminals SIAMEZE* Standard and Fine Range Terminals Application Specification 25 JAN 19 Rev E NOTE All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters

More information

DEC 09 Rev E

DEC 09 Rev E Customer Manual 409-2197 07 DEC 09 Rev E SAFETY PRECAUTIONS READ THIS FIRST!... 2 1. INTRODUCTION... 3 1.1. The Manual... 3 1.2. Purpose of the Hot Stick Kit... 3 1.3. Contents of the Hot Stick Kit...

More information

HAND CRIMP TOOL SPECIFICATION SHEET Order No

HAND CRIMP TOOL SPECIFICATION SHEET Order No HAND CRIMP TOOL SPECIFICATION SHEET Order No. 63811-6500 TYPE 2C FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly

More information

HAND CRIMP TOOL. Specification Sheet Order No

HAND CRIMP TOOL. Specification Sheet Order No HAND CRIMP TOOL Specification Sheet Order No. 63819-2300 FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly

More information