FORGED BRASS & STEEL FITTINGS "NPT" and "NPT 45 SAE"

Transcription

1 FORGED BRASS & STEEL FITTINGS "NPT" and "NPT 45 SAE"

2 BRASS FLARED TUBE FITTINGS "STANDARD FLARE SAE 45 " FITTING CONNECTIONS RANGE Standard MALE FLARE SAE 45 Standard FEMALE FLARE SAE 45 Standard MPT (male NATIONAL PIPE THREAD) Standard FPT (female NATIONAL PIPE THREAD) EXCELLENT PULL OUT, MAKE and BREAK, GOOD VIBRATION RESISTANCE, LOW COST, EASY ASSEMBLY and... THE LARGEST SELECTION IMMEDIATELY AVAILABLE FROM STOCK... PURPOSE These FLARE SAE 45 fittings are widely used for: - REFRIGERATION - AIR CONDITIONING - MARINE and AIRCRAFT industries - Flammable liquid and OIL industries DESCRIPTION These economical fittings resist mechanical pullout. Can be assembled and dissassembled repeatedly. Long dryseal pipe thread (IMPORTANT: strictly in ACCORDANCE with the STANDARDS) minimize leakage and provide more clearance for tightening flare nuts. Grooved shapes, elbows, tees, etc... made from brass forgings to maximize strength and eliminate cracks. SPECIFICATIONS These FLARE SAE 45 fittings may be used with copper, brass, aluminium, steel and plastic tube provided an acceptable flare can be generated with the material. Vacuum to pressures of 350 bar (5000 Psi) can be handled dependent upon size, material and conditions. Using a safety factor the following general rule (excluding plastic tube) is used for copper tubing under 73 C (63 F): 90 bar (800 Psi) for tubing up to /8 35 bar (900 Psi) for tubing up to 3 /6 00 bar (400 Psi) for tubing up to /4 85 bar (00 Psi) for tubing up to 5 /6 70 bar (000 Psi) for tubing up to 3 /8 53 bar (750 Psi) for tubing up to / 46 bar (650 Psi) for tubing up to 5 /8 39 bar (550 Psi) for tubing up to 3 /4 3 bar (450 Psi) for tubing up to 7 /8 Temperature ranges: -54 C to +0 C (-65 C to +50 F) INSTALLATION & INSTRUCTIONS Note that short nuts may be used when vibration is minimal. Long nuts are recommended when vibration is a factor. Tubing should be double flared in extreme applications to minimize flare thinning on over-tightening (see our flaring tool FT-95 page 79). ASSEMBLY INSTRUCTIONS: - Cut tube and remove burr (see our tools section). - Slide nut on tube, threaded end facing end of tube. - Flare tube following flaring tool manufacturer instructions to provide 45 SAE flare. - Thread nut on to fitting body handtight. - With correct wrench tighten to a solid feel. ATTENTION: - Over-tightening and dirt can damage fittings and/or tube causing leaks. - Lubrication of flare faces and threads is always recommended when practical. /8" MPT 3 /8" 5 /6" /4" /8" _ 33 _

3 NORMS U.L. Listed, these FLARE SAE 45 fittings and NPT Pipe Fittings meet functional requirement of: - SAE J53C, ASA and ARI (All flare SAE) - Military std and ASTM ANSI B70- (All flare SAE) - U.S. Std National Pipe Thread (All "MPT" & "FPT") 3 SAE FLARE THREAD SIZE Ø TUBE FLARE "SAE" Ø TUBE FLARE "SAE" C 4 /8" 5 /6-4 /" 3 /4-6 3 /6" 3 /8-4 5 /8" 7 /8-4 /4" 7 /6-0 3 /4" /6-4 5 /6" / /8" /4-3 /8" 5 /8-8 " 3 /8-7 /6" /6-6 FLARE CROSS (4 x male flare) C-04 4 x /4" male flare SAE C-06 4 x 3 /8" male flare SAE TORQUE FOR SAE FLARE FITTINGS After handtight any SAE flare fittings, use the correct wrench to tighten it by.5 turns or use the correct wrench as follows: B TUBE RECOMMENDED MAXIMUM DIAM. TORQUE TORQUE /4", N.m (9 ft.lbs) 3,5 N.m (0 ft.lbs) 3 /8" 7,0 N.m (0 ft.lbs) 33,7 N.m (5 ft.lbs) /" 40,5 N.m (30 ft.lbs) 47, N.m (35 ft.lbs) 5 /8" 60,8 N.m (45 ft.lbs) 74, N.m (55 ft.lbs) RED COPPER FLARE BONNET (Used with flare NUT to cap and close any flare fittings) B-04 For /4" flare SAE B-06 For 3 /8" flare SAE B-08 For /" flare SAE B-0 For 5 /8" flare SAE B- For 3 /4" flare SAE E FLARE x MALE PIPE 90 ELBOW (Male flare x MPT male pipe) E-03A 3 /6" male fl. SAE x /8" MPT male pipe E-04A /4" male fl. SAE x /8" MPT male pipe E-04B /4" male fl. SAE x /4" MPT male pipe E-04C /4" male fl. SAE x 3 /8" MPT male pipe E-05B 5 /6" male fl. SAE x /4" MPT male pipe E-06A 3 /8" male fl. SAE x /8" MPT male pipe E-06B 3 /8" male fl. SAE x /4" MPT male pipe E-06C 3 /8" male fl. SAE x 3 /8" MPT male pipe E-06D 3 /8" male fl. SAE x /" MPT male pipe E-08B /" male fl. SAE x /4" MPT male pipe E-08C /" male fl. SAE x 3 /8" MPT male pipe E-08D /" male fl. SAE x /" MPT male pipe E-08E /" male fl. SAE x 3 /4" MPT male pipe E-0C 5 /8" male fl. SAE x 3 /8" MPT male pipe E-0D 5 /8" male fl. SAE x /" MPT male pipe E-0E 5 /8" male fl. SAE x 3 /4" MPT male pipe E-D 3 /4" male fl. SAE x /" MPT male pipe E-E 3 /4" male fl. SAE x 3 /4" MPT male pipe B RED COPPER FLARE GASKET (Put in between brass to brass or to steel or to copper for high sealing) B-03 For 3 /6" flare SAE B-04 For /4" flare SAE B-05 For 5 /6" flare SAE B-06 For 3 /8" flare SAE B-08 For /" flare SAE B-0 For 5 /8" flare SAE B- For 3 /4" flare SAE E 90 FLARE STANDARD ELBOW ( x male flare) E-04 x /4" male flare SAE E-06 x 3 /8" male flare SAE E-08 x /" male flare SAE E-0 x 5 /8" male flare SAE E- x 3 /4" male flare SAE _ 34 _

4 E3 FPA FLARE x FEMALE PIPE 90 ELBOW (Male flare x FPT female pipe) E3-04A /4" male fl. SAE x /8" FPT female E3-04B /4" male fl. SAE x /4" FPT female E3-05B 5 /6" male fl. SAE x /4" FPT female E3-06A 3 /8" male fl. SAE x /8" FPT female E3-06B 3 /8" male fl. SAE x /4" FPT female E3-06C 3 /8" male fl. SAE x 3 /8" FPT female E3-06D 3 /8" male fl. SAE x /" FPT female E3-08C /" male fl. SAE x 3 /8" FPT female E3-08D /" male fl. SAE x /" FPT female E3-5D 5 /8" male fl. SAE x /" FPT female FUSIBLE PIPE PLUG (MPT male pipe end connection) (U.L. listed and relief opening to the temperat./pressure labeled) FPA-68 /8" MPT male pipe for 76 C FPA-0 /8" MPT male pipe for 99 C FPA-83 /8" MPT male pipe for 39 C FPB-68 /4" MPT male pipe for 76 C FPB-0 /4" MPT male pipe for 99 C FPB-83 /4" MPT male pipe for 39 C FPC-68 3 /8" MPT male pipe for 76 C FPC-0 3 /8" MPT male pipe for 99 C FPC-83 3 /8" MPT male pipe for 39 C Note: To be used only in small installations, if the working pressure is smaller or equal to 5 bar and if the volume is smaller or equal to liter. E4 x FLARE 90 ELBOW (Female flare x male flare) (Shipped with copper gasket) E4-44 /4" fem. fl. SAE x /4" male fl. SAE E /8" fem. fl. SAE x 3 /8" male fl. SAE E4-88 /" fem. fl. SAE x /" male fl. SAE HNS4 HEAVY PATTERN SHORT NUT (Old style for refrigeration, air conditioning, marine and aircraft, oil and high vibrations) ER HNS4-04 HNS4-06 HNS4-08 HNS4-0 HNS4- /4" female flare SAE 3 /8" female flare SAE /" female flare SAE 5 /8" female flare SAE 3 /4" female flare SAE x FLARE REDUCING 90 ELBOW (Male flare x male flare) ER /8" male fl. SAE x /4" male fl. SAE ER-0084 /" male fl. SAE x /4" male fl. SAE ER-0086 /" male fl. SAE x 3 /8" male fl. SAE ER /8" male fl. SAE x /" male fl. SAE K ES4 SWIVEL FEMALE FLARE 90 ELBOW (Swivel female flare x male flare) ES /4" swivel fem. fl. SAE x /4" male fl. SAE ES /8" swivel fem. fl. SAE x 3 /8" male fl. SAE ES /" swivel fem. fl. SAE x /" male fl. SAE ES /8" swivel fem. fl. SAE x 5 /8" male fl. SAE ES4-3 /4" swivel fem. fl. SAE x 3 /4" male fl. SAE REFRIGERANT DRUM ADAPTER (Female NPS cylinder x male flare) (Shipped with fibre gasket for refrigerant cylinder) K-08 /" FPT fem pipe x /4" male fl. SAE K-0 3 /4" FPT fem pipe x /4" male fl. SAE K-03 3 /4" FPT fem pipe x 3 /8" male fl. SAE K-05 3 /4" FPT fem pipe x /" male fl. SAE K-0 Cylinder adapter /4 M - 8/50 F K- Cylinder adapter 3 /8 M - 8/50 F K- Cylinder adapter /4 M -, 7/, 84 F K-3 Cylinder adapter 3 /8 M -, 7/, 84 F K-D Gasket for K-8 K-E Gasket for K-, K-3 and K-5 _ 35 _

5 NRS4 FINGER TIGHT FLARE CAP + GASKET (With NEOPRENE seal) FORGED REDUCING STD. FLARE NUT (Popular standard reducing nut) MV-45 /4" female flare SAE NFT5-6 3 /8" female flare SAE NOTE: see also page 6. NRS4-3 /8x6mm NRS4-3 /8x8mm NRS4- /x0mm NRS4-5 /8xmm NRS4-5 /8x5mm NRS4-3 /4x6mm NRS4-7 /8x0mm female flare SAE female flare SAE female flare SAE female flare SAE female flare SAE female flare SAE female flare SAE N SHORT ROD NUT (Not for Refrigeration) N-04 /4" female flare SAE N-05 5 /6" female flare SAE N-06 3 /8" female flare SAE N-08 /" female flare SAE N-0 5 /8" female flare SAE N- 3 /4" female flare SAE NRS4 FORGED REDUCING STD. FLARE NUT (Popular standard reducing nut) NRS /4" female flare SAE x 3 /6" NRS /6" female flare SAE x /4" NRS /8" female flare SAE x /4" NRS /8" female flare SAE x 5 /6" NRS /" female flare SAE x 3 /8" NRS /8" female flare SAE x /" NRS4-0 3 /4" female flare SAE x 5 /8" N4 LONG FORGED SECURITY NUT (High vibration resistance) N4-04 /4" female flare SAE N /6" female flare SAE N /8" female flare SAE N4-08 /" female flare SAE N4-0 5 /8" female flare SAE N4-3 /4" female flare SAE NS4 SHORT FORGED STANDARD NUT (The most popular standard nut) NS4-03 NS4-04 NS4-05 NS4-06 NS4-08 NS4-0 NS4-3 /6" female flare SAE /4" female flare SAE 5 /6" female flare SAE 3 /8" female flare SAE /" female flare SAE 5 /8" female flare SAE 3 /4" female flare SAE N5 FEMALE FLARE CAP (Hexagonal head) N5-04 /4" female flare SAE N /6" female flare SAE N /8" female flare SAE N5-08 /" female flare SAE N5-0 5 /8" female flare SAE N5-3 /4" female flare SAE NS4 SHORT FORGED STANDARD NUT (The most popular standard nut) NS4-06mm 6 mm x /4" female flare SAE NS4-0mm 0 mm x 3 /8" female flare SAE NS4-mm mm x /" female flare SAE NS4-6mm 6 mm x 5 /8" female flare SAE NS4-8mm 8 mm x 3 /4" female flare SAE NS4-mm mm x 7 /8" female flare SAE _ 36 _

6 (MPT) P T3 3 MALE FLARE PLUG (Hexagonal head) P-03 3 /6" male flare SAE P-04 /4" male flare SAE P-05 5 /6" male flare SAE P-06 3 /8" male flare SAE P-08 /" male flare SAE P-0 5 /8" male flare SAE P- 3 /4" male flare SAE OTHER FLARE x MPT PIPE TEE (Male Flare x MPT Male Pipe x Male Flare) T3-04A x /4" Male Fl. SAE x /8" MPT Male pipe T3-04B x /4" Male Fl. SAE x /4" MPT Male pipe T3-06B x 3 /8" Male Fl. SAE x /4" MPT Male pipe T3-08D x /" Male Fl. SAE x /" MPT Male pipe T3-0D x 5 /8" Male Fl. SAE x /" MPT Male pipe T3-E x 3 /4" Male Fl. SAE x 3 /4" MPT Male pipe T x MALE FLARE x MPT PIPE TEE ( x "in line" male flare x MPT male pipe) T-04A x /4" male fl. SAE x /8" NPT male pipe T-04B x /4" male fl. SAE x /4" NPT male pipe T-04C x /4" male fl. SAE x 3 /8" NPT male pipe T-06B x 3 /8" male fl. SAE x /4" NPT male pipe T-06C x 3 /8" male fl. SAE x 3 /8" NPT male pipe T-08C x /" male fl. SAE x 3 /8" NPT male pipe T-08D x /" male fl. SAE x /" NPT male pipe T-0C x 5 /8" male fl. SAE x 3 /8" NPT male pipe T-0D x 5 /8" male fl. SAE x /" NPT male pipe 3 TR U 3 REDUCING FLARE TEE (3 x male flare) TR x /4" male fl. SAE x 3 /8" male fl. SAE TR x 3 /8" male fl. SAE x /4" male fl. SAE TR x 3 /8" male fl. SAE x /" male fl. SAE TR x /" male fl. SAE x 3 /8" male fl. SAE T FLARE TEE (3 x male flare) T-04 3 x /4" male flare SAE T-05 3 x 5 /6" male flare SAE T-06 3 x 3 /8" male flare SAE T-08 3 x /" male flare SAE T-0 3 x 5 /8" male flare SAE T- 3 x 3 /4" male flare SAE T6 x MALE FLARE x FEMALE FLARE TEE ( x in line male flare x female flare) (Shipped with copper gasket on female end) T6-4 x /4" male fl. SAE x /4" fem. fl. SAE 3 MALE FLARE x MALE NPT PIPE ADAPTER (Male flare x MPT male pipe) U-03A 3 /6" male fl. SAE x /8" MPT pipe U-04A /4" male fl. SAE x /8" MPT pipe U-04B /4" male fl. SAE x /4" MPT pipe U-04C /4" male fl. SAE x 3 /8" MPT pipe U-04D /4" male fl. SAE x /" MPT pipe U-05A 5 /6" male fl. SAE x /8" MPT pipe U-05B 5 /6" male fl. SAE x /4" MPT pipe U-05C 5 /6" male fl. SAE x 3 /8" MPT pipe U-06A 3 /8" male fl. SAE x /8" MPT pipe U-06B 3 /8" male fl. SAE x /4" MPT pipe U-06C 3 /8" male fl. SAE x 3 /8" MPT pipe U-06D 3 /8" male fl. SAE x /" MPT pipe U-06E 3 /8" male fl. SAE x 3 /4" MPT pipe U-08A /" male fl. SAE x /8" MPT pipe U-08B /" male fl. SAE x /4" MPT pipe U-08C /" male fl. SAE x 3 /8" MPT pipe U-08D /" male fl. SAE x /" MPT pipe U-08E /" male fl. SAE x 3 /4" MPT pipe U-0B 5 /8" male fl. SAE x /4" MPT pipe U-0C 5 /8" male fl. SAE x 3 /8" MPT pipe U-0D 5 /8" male fl. SAE x /" MPT pipe U-0E 5 /8" male fl. SAE x 3 /4" MPT pipe U-D 3 /4" male fl. SAE x /" MPT pipe U-E 3 /4" male fl. SAE x 3 /4" MPT pipe _ 37 _

7 U STRAIGHT FLARE UNION (Male flare x male flare) U-03 x 3 /6" male flare SAE U-04 x /4" male flare SAE U-05 x 5 /6" male flare SAE U-06 x 3 /8" male flare SAE U-08 x /" male flare SAE U-0 x 5 /8" male flare SAE U- x 3 /4" male flare SAE U5 FEMALE FLARE x MPT ADAPTER (Female flare x MPT male pipe) (Shipped with copper gasket) U5-04A /4" fem. fl. SAE x /8" MPT male U5-04B /4" fem. fl. SAE x /4" MPT male U5-06B 3 /8" fem. fl. SAE x /4" MPT male U5-08D /" fem. fl. SAE x /" MPT male U3 MALE FLARE x FPT PIPE ADAPTER (Male flare x FPT female pipe) U3-04A /4" male flare SAE x /8" FPT pipe U3-04B /4" male flare SAE x /4" FPT pipe U3-04C /4" male flare SAE x 3 /8" FPT pipe U3-05A 5 /6" male flare SAE x /8" FPT pipe U3-05B 5 /6" male flare SAE x /4" FPT pipe U3-06A 3 /8" male flare SAE x /8" FPT pipe U3-06B 3 /8" male flare SAE x /4" FPT pipe U3-06C 3 /8" male flare SAE x 3 /8" FPT pipe U3-06D 3 /8" male flare SAE x /" FPT pipe U3-08B /" male flare SAE x /4" FPT pipe U3-08C /" male flare SAE x 3 /8" FPT pipe U3-08D /" male flare SAE x /" FPT pipe U3-0C 5 /8" male flare SAE x 3 /8" FPT pipe U3-0D 5 /8" male flare SAE x /" FPT pipe U3-0E 5 /8" male flare SAE x 3 /4" FPT pipe U6 FEMALE FLARE x FPT UNION (Female flare x FPT female pipe) (Shipped with copper gasket on Flare end) U6-4A /4" fem. fl. SAE x /8" fem. FPT pipe U6-4B /4" fem. fl. SAE x /4" fem. FPT pipe UR U4 x SAE FLARE CONNECTOR (Female flare x female flare) (shipped with copper gaskets) U4-04 x /4" female flare SAE U4-06 x 3 /8" female flare SAE U4-08 x /" female flare SAE U4-0 x 5 /8" female flare SAE U4- x 3 /4" female flare SAE REDUCING FLARE UNION (Male flare x male flare) UR-0043 /4" x 3 /6" male flare SAE UR /6" x /4" male flare SAE UR /8" x /4" male flare SAE UR /8" x 5 /6" male flare SAE UR-0084 /" x /4" male flare SAE UR-0086 /" x 3 /8" male flare SAE UR /8" x /4" male flare SAE UR /8" x 3 /8" male flare SAE UR /8" x /" male flare SAE UR-08 3 /4" x /" male flare SAE UR-0 3 /4" x 5 /8" male flare SAE _ 38 _

8 UR3 US5 FEMALE x MALE FLARE ADAPTER (Hex female flare x male flare) (Shipped with copper gasket) UR /4" fem. fl. SAE x 3 /8" male fl. SAE UR /4" fem. fl. SAE x /" male fl. SAE UR /8" fem. fl. SAE x /4" male fl. SAE UR /8" fem. fl. SAE x 5 /6" male fl. SAE UR /8" fem. fl. SAE x /" male fl. SAE UR /" fem. fl. SAE x /4" male fl. SAE UR /" fem. fl. SAE x 3 /8" male fl. SAE UR3-080 /" fem. fl. SAE x 5 /8" male fl. SAE UR /8" fem. fl. SAE x 3 /8" male fl. SAE UR /8" fem. fl. SAE x /" male fl. SAE UR3-0 5 /8" fem. fl. SAE x 3 /4" male fl. SAE UR3-0 3 /4" fem. fl. SAE x 5 /8" male fl. SAE SWIVEL FEMALE FLARE CONNECTOR x O.D.S. SOLDER END ADAPTER (Swivel female flare x O.D.S. solder) US US US US5-00 /4" female flare SAE x /4" ODS 3 /8" female flare SAE x 3 /8" ODS /" female flare SAE x /" ODS 5 /8" female flare SAE x 5 /8" ODS US3 FLARE x SOLDER HEX ADAPTER (Male flare x O.D.S. solder end) US /4" male flare SAE x /4" ODS US /4" male flare SAE x 5 /6" ODS US /4" male flare SAE x 3 /8" ODS US /8" male flare SAE x /4" ODS US /8" male flare SAE x 5 /6" ODS US /8" male flare SAE x 3 /8" ODS US /8" male flare SAE x /" ODS US /8" male flare SAE x 5 /8" ODS US /" male flare SAE x 3 /8" ODS US /" male flare SAE x /" ODS US3-080 /" male flare SAE x 5 /8" ODS US /8" male flare SAE x /" ODS US /8" male flare SAE x 5 /8" ODS US3-0 5 /8" male flare SAE x 3 /4" ODS US /8" male flare SAE x 7 /8" ODS US3-3 /4" male flare SAE x 3 /4" ODS US3-4 3 /4" male flare SAE x 7 /8" ODS USTK STEK COUPLING USTK-04 Stek coupling /4" USTK-06 Stek coupling 3 /8" USTK-08 Stek coupling /" USTK-0 Stek coupling 5 /8" USTK- Stek coupling 3 /4" USTKR-46 STEK COUPLING REDUCER USTKR-46 Stek coupling reducer 3 /8" x /4" US4 SWIVEL FEMALE FLARE CONNECTOR (Female flare x swivel female flare) US4-04 x /4" female flare SAE US4-06 x 3 /8" female flare SAE US4-08 x /" female flare SAE US4-0 x 5 /8" female flare SAE UX EXTRA LONG FLARE HEX UNION (Male flare x MPT male pipe) UX-4A /4" male fl. SAE x /8" MPT pipe UX-4B /4" male fl. SAE x /4" MPT pipe _ 39 _

9 NPT PIPE FORGED BRASS FITTINGS "STANDARD NATIONAL PIPE THREAD" FITTINGS CONNECTIONS ARE: Standard MPT (Male NATIONAL PIPE THREAD) Standard FPT (Female NATIONAL PIPE THREAD) EXCELLENT PULL OUT, MAKE and BREAK, GOOD VIBRATION RESISTANCE, LOW COST, EASY ASSEMBLY and... THE LARGEST SELECTION IMMEDIATELY AVAILABLE ON STOCK... PURPOSE, SPECIFICATION & NORMS: See "BRASS FLARED TUBE FITTINGS" section, page B 03-B FORGED 90 ELBOW ( x FPT female pipe) HEX COUPLING ( x FPT female pipe) 00-B-0 00-B B B-08 /8" FPT /4" FPT 3 /8" FPT /" FPT 03-B-0 03-B B B-08 /8" FPT /4" FPT 3 /8" FPT /" FPT 0-B 04-B FORGED TEE (3 x FPT female pipe) HEX 3 PIECES UNIONS ( x FPT female pipe) 0-B-0 0-B-04 0-B-06 0-B-08 /8" FPT /4" FPT 3 /8" FPT /" FPT 04-B-04 /4" FPT 08-B 0-B FORGED CROSS (4 x FPT female pipe) 0-B-06 0-B-08 3 /8" FPT /" FPT FEMALE CAP (FPT female pipe) 08-B-0 08-B B B-08 /8" FPT /4" FPT 3 /8" FPT /" FPT _ 40 _

10 09-B MALE SQUARE HEAD PLUG (MPT male pipe) 09-B-0 09-B B B-08 /8" MPT /4" MPT 3 /8" MPT /" MPT 3-B LONG NIPPLE ( x MPT male pipe) 3-B-0x4 3-B-04x4 3-B-04x3 3-B-04x48 Long nipple /8" MPT - 38 mm Long nipple /4" MPT - 38 mm Long nipple /4" MPT - 5 mm Long nipple /4" MPT - 76 mm 0-B 6-B HEX BUSHING (MPT male pipe x FPT female pipe) FORGED 90 STREET ELBOW (MPT male pipe x FPT female pipe) 0-B-04x0 0-B-06x0 0-B-06x04 0-B-08x0 0-B-08x04 0-B-08x06 0-B-x06 0-B-x08 /4" MPT x /8" FPT 3 /8" MPT x /8" FPT 3 /8" MPT x /4" FPT /" MPT x /8" FPT /" MPT x /4" FPT /" MPT x 3 /8" FPT 3 /4" MPT x 3 /8" FPT 3 /4" MPT x /" FPT 6-B-0 6-B-04 6-B-06 6-B-08 /8" MPT x /8" FPT /4" MPT x /4" FPT 3 /8" MPT x 3 /8" FPT /" MPT x /" FPT -B 7-B HEX LOCK NUT (Through wall maintening) SLOTTED PLUG (MPT male pipe) -B-0 -B-04 -B-06 -B-08 /8" FPT /4" FPT 3 /8" FPT /" FPT 7-B-0 7-B-04 7-B-06 /8" MPT /4" MPT 3 /8" MPT -B 9-B CROSS NIPPLE ( x MPT male pipe) -B-0 -B-04 -B-06 -B-08 /8" MPT /4" MPT 3 /8" MPT /" MPT HEX REDUCING BUSHING (FPT female pipe x FPT female pipe) 9-B-04x0 9-B-06x04 9-B-08x06 /4" FPT x /8" FPT 3 /8" FPT x /4" FPT /" FPT x 3 /8" FPT _ 4 _

11 0-B -B HEX ADAPTER (FPT female pipe x MPT male pipe) HEX NIPPLE ( x MPT male pipe) 0-B-0x0 0-B-04x04 0-B-06x06 0-B-08x08 /8" FPT x /8" MPT /4" FPT x /4" MPT 3 /8" FPT x 3 /8" MPT /" FPT x /" MPT -B-0 -B-04 -B-06 -B-08 /8" MPT /4" MPT 3 /8" MPT /" MPT 0-B HEX ADAPTER (FPT female pipe x MPT male pipe) 0-B-04x0 0-B-06x04 0-B-08x06 /4" FPT x /8" MPT 3 /8" FPT x /4" MPT /" FPT x 3 /8" MPT 3-B REDUCING HEX NIPPLE ( x MPT male pipe) 3-B-04x0 /4" MPT x /8" MPT 3-B-06x04 3 /8" MPT x /4" MPT -B HEX HEAD PLUG (MPT male pipe) -B-0 -B-04 -B-06 -B-08 -B- /8" MPT /4" MPT 3 /8" MPT /" MPT 3 /4" MPT 9-B BULKHEAD ADAPTER (Through wall anchor) 9-B-0x4 9-B-04x5 /8" FPT - Length: 38 mm /4" FPT - Length: 33 mm _ 4 _

12 REFRIGERATION STEEL FITTINGS "STEEL 3000 & SCHEDULE 80" DESCRIPTION All these "NPT" FORGED STEEL FITTINGS & UNIONS are suitable for:- REFRIGERATION - AIR-CONDITIONING - MARINE and OIL industries Both threads are Male thread (MPT) or Female thread (FPT) and are designated as follows: - "NPT": National Pipe Thread according to the US std - "BRIGGS": Name of the discoverer engineer - "PIPE": Inexplicit term used sometimes. (There is no similarity with "GAS" or "BSP" threads) Meanwhile, to define these specific "NPT" steel threaded fittings and unions, professional terms normally used are: - "MPT" = NPT male thread - "FPT" = NPT female thread - "BUTT WELD" = To be welded (same Ø of the pipe) - "SW" = welding of socket weld end SPECIFICATIONS Metal/metal thread contact. Leak proof under high pressure. All these steel fittings are "PHOSPHATIZED". This process consists of a chemical treatment to protect steel fittings against corrosion (60 hours of resistance under spray salt) and to increase the safety of the installation against leakage. Phosphatized fittings offer mechanical advantages and reduce tightening torque for a leak proof installation (by 0%). Also, if these steel fittings must often be disassembled and reassembled, there is no risk of seizing. NORMES A.S.T.M. = A-8 and A-05 A.I.S.I. = 00 AFNOR = XC8 S BRITISH STD = 503 and 6-GR B DIN = CK Specifications = ASA-B6- and BS-3799 Threading = API-5B or ASA-B- GENERAL PURPOSE Multi threading uses and easy and safe assembling for: Level liquid Indicators (on piping, in line, receivers, etc...). Steel or brass relief-valve threadings (inlet, outlet, etc...). Level float-switch or level controller assemblies. Gauges, manifolds, service valves, expansion valves, etc... Water solenoïd or pressostatic valves, etc... Glycool water pipings and all other refrigeration and airconditioning systems, etc... INSTALLATION To prevent crackings of the weld (socket-weld ends), it is safer to withdraw the pipe approximately,5 mm ( /6 inch) away from the bottom of the socket. SCREW ENDS Normal engagement between male and female threads to make tight joints according to standard ASA-B. - or API Std 5 B. P L L Taper of thread /6" (,5 mm) measured on Ø D E0 E REFRIGERATION FITTINGS _ 43 _

13 CFF FEMALE ELBOWS (FPT x FPT) CFF-90-0 times /4" CFF times 3 /8" CFF times /" CFF times 3 /4" CFF times " CFF-90-0 times /4" CFF-90- times /" CFF-90-6 times " CRX FEMALE CROSSES (FPT x FPT x FPT x FPT) CRX-0 4 times /4" CRX-03 4 times 3 /8" CRX-04 4 times /" CRX-06 4 times 3 /4" CRX-08 4 times " CRX-0 4 times /4" CRX- 4 times /" CFF FEMALE ELBOWS (FPT x FPT) CFF-45-0 times /4" CFF times 3 /8" CFF times /" CFF times 3 /4" CFF times " CFF-45-0 times /4" CMF MALE x FEMALE ELBOWS (FPT x MPT) CMF-90-0 times /4" CMF times 3 /8" CMF times /" CMF times 3 /4" CMF times " CMF-90-0 times /4" T3F FEMALE TEES (FPT x FPT x FPT) T3F-0 3 times /4" T3F-03 3 times 3 /8" T3F-04 3 times /" T3F-06 3 times 3 /4" T3F-08 3 times " T3F-0 3 times /4" T3F- 3 times /" T3F-6 3 times " CD STEEL COUPLINGS (FPT x FPT) CD-0 times /4" CD-03 times 3 /8" CD-04 times /" CD-06 times 3 /4" CD-08 times " CD-0 times /4" CD- times /" _ 44 _

14 CDR UMF FEMALE REDUCING COUPLINGS (FPT x FPT) CDR /8" x /4" CDR /" x 3 /8" CDR /4" x 3 /8" CDR /4" x /" CDR " x 3 /4" CDR-0-08 /4" x " CDR--0 /" x /4" CDR-6-0 " x /4" CDR-6- " x /" 3 PIECES UNIONS (MPT x SW) UMF-0 /4" MPT x /4" SW socket welding UMF-03 3 /8" MPT x 3 /8" SW socket welding UMF-04 /" MPT x /" SW socket welding UMF-06 3 /4" MPT x 3 /4" SW socket welding UMF-08 " MPT x " SW socket welding UMF-0 /4" MPT x /4" SW socket welding UMF- /" MPT x /" SW socket welding UMF-6 " MPT x " SW socket welding Typical for single or dual relief-valve outlets M-MM HEXAGONAL NIPPLES (MPT x MPT) M-MM-0 times /4" M-MM-03 times 3 /8" M-MM-04 times /" M-MM-06 times 3 /4" M-MM-08 times " M-MM-0 times /4" M-MM- times /" M-MM-6 times " UFF 3 PIECES UNIONS (FPT x FPT) UFF-0 times /4" UFF-03 times 3 /8" UFF-04 times /" UFF-06 times 3 /4" UFF-08 times " UFF-0 times /4" UFF- times /" MR-MM MT REDUCING HEXAGONAL NIPPLES (MPT x MPT) MR-MM-03 3 /8" x /4" MR-MM-04 /" x /4" MR-MM-043 /" x 3 /8" MR-MM /4" x /" MR-MM-08 " x /4" MR-MM-084 " x /" MR-MM-086 " x 3 /4" MR-MM-06 /4" x 3 /4" MR-MM-08 /4" x " BARREL NIPPLES (MPT x BUTT WELD) MT-0 times /4" butt weld MT-03 times 3 /8" butt weld MT-04 times /" butt weld MT-06 times 3 /4" butt weld MT-08 times " butt weld MT-0 times /4" butt weld MT- times /" butt weld MT-6 times " butt weld MT-0 times /" butt weld MT-4 times 3" butt weld _ 45 _

15 BF RED-MF FEMALE ROUND CAPS (FPT) BF-0 /8" BF-0 /4" BF-03 3 /8" BF-04 /" BF-06 3 /4" BF-08 " BF-0 /4" BF- /" BF-6 " BF-0 /" BF-4 3" HEXAGONAL HEAD BUSHINGS (MPT x FPT) RED-MF /8" x /4" RED-MF-004 /" x /4" RED-MF-0043 /" x 3 /8" RED-MF /4" x /4" RED-MF /4" x /" RED-MF-0084 " x /" RED-MF-0086 " x 3 /4" RED-MF-006 /4" x 3 /4" RED-MF-008 /4" x " RED-MF-08 /" x " RED-MF-0 /" x /4" BS FEMALE WELD COUPLETS (FPT x BUTT WELD) BS-0 times /4" butt weld BS-03 times 3 /8" butt weld BS-04 times /" butt weld BS-06 times 3 /4" butt weld BS-08 times " butt weld BS-0 times /4" butt weld BS- times /" butt weld BM MALE HEXAGONAL HEAD PLUGS (MPT) BM-0 /8" BM-0 /4" BM-03 3 /8" BM-04 /" BM-06 3 /4" BM-08 " BM-0 /4" BM- /" BM-6 " BM-0 /" BM-4 3" _ 46 _

16 REFRIGERATION STEEL FITTINGS "STEEL 3000 & SCHEDULE 80" 0,5 à "SOCKET WELD END" FORGED STEEL FITTINGS E C.5 maxi A F 0,5-0 +0,5 B DESCRIPTION All these steel fittings are identical to the steel fittings shown on the preceding pages but offer "SOCKET WELD END" assemblies only. See "SW" definition on page 43. C 0,5 à ± 00 SPECIFICATION and NORMS ANSI-B and BS ANSI-B 6.5 (For all "butt weld" connections as BS and BS-S types) ASTM, AFNOR, AISI and DIN (see page 43) C.5 maxi E A G PURPOSE REFRIGERATION AIR CONDITIONING MARINE and OIL industries Free welding steel pipes (norm NFE 0-00) Tarif 0 steel pipes (norm NFA ) Low temperature refrigeration pipes Water, steam, oil, chemistry and high pressure pipes L 0,8B B D (see nota) B e nominal pipe NOTE e = Nominal pipe thickness. B mini =,09 e (nominal) but never less than 3, mm ( /8") seal weld INSTALLATION To prevent crackings of the weld (socket weld ends), it is safer to withdraw the pipe approximately,5 mm ( /6") away from the bottom of the socket.,5 maxi fitting CFF-S SOCKET FEMALE ELBOWS (SW x SW) CFF-S-90-0 times /4" CFF-S times 3 /8" CFF-S times /" CFF-S times 3 /4" CFF-S times " CFF-S-90-0 times /4" CFF-S-90- times /" CFF-S-90-6 times " CFF-S-90-0 times /" CFF-S-90-4 times 3" CFF-S SOCKET FEMALE ELBOWS (SW x SW) CFF-S-45-0 times /4" CFF-S times 3 /8" CFF-S times /" CFF-S times 3 /4" CFF-S times " CFF-S-45-0 times /4" CFF-S-45- times /" CFF-S-45-6 times " CFF-S-45-0 times /" CFF-S-45-4 times 3" _ 47 _

17 T3F-S RED-FF-S SOCKET FEMALE TEES (SW x SW x SW) T3F-S-0 3 times /4" T3F-S-03 3 times 3 /8" T3F-S-04 3 times /" T3F-S-06 3 times 3 /4" T3F-S-08 3 times " T3F-S-0 3 times /4" T3F-S- 3 times /" T3F-S-6 3 times " T3F-S-0 3 times /" T3F-S-4 3 times 3" SOCKET FEMALE REDUCING COUPLINGS (SW x SW) RED-FF-S-00 /4" x /8" RED-FF-S /8" x /4" RED-FF-S-004 /" x /4" RED-FF-S-0043 /" x 3 /8" RED-FF-S /4" x /4" RED-FF-S /4" x 3 /8" RED-FF-S /4" x /" RED-FF-S-008 " x /4" RED-FF-S-0083 " x 3 /8" RED-FF-S-0084 " x /" RED-FF-S-0086 " x 3 /4" RED-FF-S-00 /4" x /4" RED-FF-S-003 /4" x 3 /8" RED-FF-S-004 /4" x /" RED-FF-S-006 /4" x 3 /4" RED-FF-S-008 /4" x " RED-MF-S RED-FF-S-0 /" x /4" RED-FF-S-03 /" x 3 /8" RED-FF-S-04 /" x /" RED-FF-S-06 /" x 3 /4" RED-FF-S-08 /" x " RED-FF-S-0 /" x /4" SOCKET REDUCER INSERTS (SW x SW) RED-MF-S /8" x /4" RED-MF-S-004 /" x /4" RED-MF-S-0043 /" x 3 /8" RED-MF-S /4" x /4" RED-MF-S /4" x 3 /8" RED-MF-S /4" x /" RED-MF-S-008 " x /4" RED-MF-S-0083 " x 3 /8" RED-MF-S-0084 " x /" RED-MF-S-0086 " x 3 /4" RED-FF-S-06 " x /4" RED-FF-S-063 " x 3 /8" RED-FF-S-064 " x /" RED-FF-S-066 " x 3 /4" RED-FF-S-068 " x " RED-FF-S-6 " x /" RED-FF-S-008 /" x " RED-FF-S-0 /" x /" RED-FF-S-06 /" x " RED-FF-S-4 3" x /" RED-FF-S-46 3" x " RED-FF-S-40 3" x /" RED-MF-S-004 /4" x /" RED-MF-S-006 /4" x 3 /4" RED-MF-S-008 /4" x " RED-MF-S-0 /" x /4" RED-MF-S-03 /" x 3 /8" RED-MF-S-04 /" x /" RED-MF-S-06 /" x 3 /4" RED-MF-S-08 /" x " RED-MF-S-0 /" x /4" RED-MF-S-064 " x /" RED-MF-S-068 " x " RED-MF-S-60 " x /4" RED-MF-S-6 " x /" RED-MF-S-06 /" x " _ 48 _

18 CRX-S SOCKET FEMALE CROSSES (4 x SW) CRX-S-0 4 times /4" CRX-S-03 4 times 3 /8" CRX-S-04 4 times /" CRX-S-06 4 times 3 /4" CRX-S-08 4 times " CRX-S-0 4 times /4" CRX-S- 4 times /" CRX-S-6 4 times " CRX-S-0 4 times /" CRX-S-4 4 times 3" BF-S SOCKET FEMALE ROUND CAPS (SW) BF-S-0 /4" BF-S-03 3 /8" BF-S-04 /" BF-S-06 3 /4" BF-S-08 " BF-S-0 /4" BF-S- /" BF-S-6 " BF-S-0 /" MFF-S SOCKET FEMALE COUPLINGS (SW x SW) MFF-S-0 times /4" MFF-S-03 times 3 /8" MFF-S-04 times /" MFF-S-06 times 3 /4" MFF-S-08 times " MFF-S-0 times /4" MFF-S- times /" MFF-S-6 times " MFF-S-0 times /" MFF-S-4 times 3" MFF-S-3 times 4" BS-S SOCKET WELD COUPLETS (SW x BUTT WELD) BS-S-0 times /4" BS-S-03 times 3 /8" BS-S-04 times /" BS-S-06 times 3 /4" BS-S-08 times " BS-S-0 times /4" BS-S- times /" BS-S-6 times " DMF-S SOCKET HALF COUPLINGS (SW x SW) DMF-S-0 /4" DMF-S-03 3 /8" DMF-S-04 /" DMF-S-06 3 /4" DMF-S-08 " DMF-S-0 /4" DMF-S- /" DMF-S-6 " DMF-S-0 /" DMF-S-4 3" UFF-S 3 PIECES SOCKET UNIONS (SW x SW) UFF-S-0 times /4" UFF-S-03 times 3 /8" UFF-S-04 times /" UFF-S-06 times 3 /4" UFF-S-08 times " UFF-S-0 times /4" UFF-S- times /" UFF-S-6 times " UFF-S-0 times /" UFF-S-4 times 3" _ 49 _

19 Part. nr. Pdf file Part. nr. Pdf file Part. nr. Pdf file 00-BC see Service manifolds, gauges and charging hoses 00-BC/47 see Service manifolds, gauges and charging hoses 00-BC/4 see Service manifolds, gauges and charging hoses 00-BC/447 see Service manifolds, gauges and charging hoses 00-BPC see Service manifolds, gauges and charging hoses 00-BPC/40 see Service manifolds, gauges and charging hoses 00-BPC/40/7 see Service manifolds, gauges and charging hoses 003 see Evacuating and charging equipment 004-BC see Service manifolds, gauges and charging hoses 004-BC/47 see Service manifolds, gauges and charging hoses 004-BC/4 see Service manifolds, gauges and charging hoses 004-BC/447 see Service manifolds, gauges and charging hoses 004-BPC see Service manifolds, gauges and charging hoses 004-BPC/40 see Service manifolds, gauges and charging hoses 004-BPC/40/7 see Service manifolds, gauges and charging hoses 00-B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 00-B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 00-B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 00-B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-BC see Service manifolds, gauges and charging hoses 0-BC/47 see Service manifolds, gauges and charging hoses 0-BC/4 see Service manifolds, gauges and charging hoses 0-BC/447 see Service manifolds, gauges and charging hoses 0-BPC see Service manifolds, gauges and charging hoses 0-BPC/40 see Service manifolds, gauges and charging hoses 0-BPC/40/7 see Service manifolds, gauges and charging hoses 04-BC see Service manifolds, gauges and charging hoses 04-BC/47 see Service manifolds, gauges and charging hoses 04-BC/4 see Service manifolds, gauges and charging hoses 04-BC/447 see Service manifolds, gauges and charging hoses 04-BPC see Service manifolds, gauges and charging hoses 04-BPC/40 see Service manifolds, gauges and charging hoses 04-BPC/40/7 see Service manifolds, gauges and charging hoses 0-B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 00-XFC see Copper tubes, coils & solder fittings (Inch & Metric) 0-B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 03-B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 03-B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 03-B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 03-B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 03-FS see Tube working tools 04-B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 05-MK see Electronic measurement and control instruments 084-BC see Service manifolds, gauges and charging hoses 084-BC/47 see Service manifolds, gauges and charging hoses 084-BC/4 see Service manifolds, gauges and charging hoses 084-BC/447 see Service manifolds, gauges and charging hoses 084-BPC see Service manifolds, gauges and charging hoses 084-BPC/40 see Service manifolds, gauges and charging hoses 084-BPC/40/7 see Service manifolds, gauges and charging hoses 08-B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 08-B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 08-B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 08-B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 09-B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 09-B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 09-B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 09-B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-04x0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-06x0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-06x04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-08x0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-08x04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-08x06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-x06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-x08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 3-B-0x4 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 3-B-04x4 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 3-B-04x3 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 3-B-04x48 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 6-B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 6-B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 6-B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 6-B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 7-B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 7-B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 7-B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 84-BC see Service manifolds, gauges and charging hoses 84-BC/47 see Service manifolds, gauges and charging hoses 84-BC/4 see Service manifolds, gauges and charging hoses 84-BC/447 see Service manifolds, gauges and charging hoses 84-BPC see Service manifolds, gauges and charging hoses 84-BPC/40 see Service manifolds, gauges and charging hoses 84-BPC/40/7 see Service manifolds, gauges and charging hoses 9-B-04x0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 9-B-06x04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 9-B-08x06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-0x0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-04x0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-04x04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-06x04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-06x06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-08x06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 0-B-08x08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B- see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-06 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" -B-08 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 3-B-04x0 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 3-B-06x04 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 4-RW see Tube working tools 7-RW see Tube working tools 7-RWO see Tube working tools 84-BC see Service manifolds, gauges and charging hoses 84-BC/47 see Service manifolds, gauges and charging hoses 84-BC/4 see Service manifolds, gauges and charging hoses 84-BC/447 see Service manifolds, gauges and charging hoses 84-BPC see Service manifolds, gauges and charging hoses 84-BPC/40 see Service manifolds, gauges and charging hoses 84-BPC/407 see Service manifolds, gauges and charging hoses 9-B-0x4 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 9-B-04x5 see Forged brass & steel fittings "NPT" & "NPT 45 SAE" 335-BA-03 see Fluid control components 335-BA-04 see Fluid control components 335-BA-06 see Fluid control components 34-BA-06 see Fluid control components 34-BA-08 see Fluid control components 34-BA- see Fluid control components 34-BA-6 see Fluid control components 34-BA-0 see Fluid control components 34-BA-4 see Fluid control components 34-BT-06S06 see Fluid control components 34-BT-06S06 see Fluid control components 34-BT-06S07 see Fluid control components 34-BT-06S07 see Fluid control components 34-BT-06S09 see Fluid control components 34-BT-06S09 see Fluid control components 34-BT-08S09 see Fluid control components 34-BT-08S09 see Fluid control components 34-BT-08S see Fluid control components 34-BT-08S see Fluid control components 34-BT-S3 see Fluid control components 34-BT-S3 see Fluid control components 34-BT-S7 see Fluid control components 34-BT-S7 see Fluid control components 34-BT-6S7 see Fluid control components 34-BT-6S7 see Fluid control components 34-BT-6S see Fluid control components 34-BT-6S see Fluid control components 359-FS-04 see Fluid control components 359-FS-06 see Fluid control components 359-FS-08 see Fluid control components 359-FS-0 see Fluid control components 359-FS- see Fluid control components 359-FS-6 see Fluid control components 60-BC/40 see Service manifolds, gauges and charging hoses 60-P see Refrigeration accessories 60-P5 see Refrigeration accessories 6-BC/40 see Service manifolds, gauges and charging hoses 6-BC/40 see Service manifolds, gauges and charging hoses 680 see Service manifolds, gauges and charging hoses 680 see Service manifolds, gauges and charging hoses 6803 see Service manifolds, gauges and charging hoses 6-C see Service manifolds, gauges and charging hoses 6-C see Automatic access valves & fittings 74-F see Tube working tools 74-F-SP see Tube working tools 7-C see Automatic access valves & fittings 80-A see Copper tubes, coils & solder fittings (Inch & Metric) 80-B see Copper tubes, coils & solder fittings (Inch & Metric) 80-BPC/40 see Service manifolds, gauges and charging hoses 80-XFC see Copper tubes, coils & solder fittings (Inch & Metric) 803 see Copper tubes, coils & solder fittings (Inch & Metric) 8-BPC/40 see Service manifolds, gauges and charging hoses 8-BPC/40 see Service manifolds, gauges and charging hoses 87 see Copper tubes, coils & solder fittings (Inch & Metric) 8-C see Automatic access valves & fittings 93-S see Tube working tools 93-S-SP see Tube working tools 95-FB see Tube working tools 95-FC see Tube working tools 95-FC-SP see Tube working tools 9-C see Automatic access valves & fittings 00-VG see Service manifolds, gauges and charging hoses 00-VG see Service manifolds, gauges and charging hoses 03-FA see Tube working tools 04-BT- see Fluid control components 04-BT- see Fluid control components 04-BT-S see Fluid control components 04-BT-S see Fluid control components 04-BT-3 see Fluid control components 04-BT-3 see Fluid control components 04-BT-3S3 see Fluid control components 04-BT-3S3 see Fluid control components 04-BT-4 see Fluid control components 04-BT-4 see Fluid control components 04-BT-4S4 see Fluid control components 04-BT-4S4 see Fluid control components 04-BT-4S5 see Fluid control components 04-BT-4S5 see Fluid control components 04-BT-5 see Fluid control components 04-BT-5 see Fluid control components 04-BT-5S5 see Fluid control components 04-BT-5S5 see Fluid control components 04-BT-5S6 see Fluid control components 04-BT-5S6 see Fluid control components 04-BT-5S7 see Fluid control components 04-BT-5S7 see Fluid control components 05-P06 see Evacuating and charging equipment 05-P06 see Refrigeration accessories 05-P see Evacuating and charging equipment 05-P see Refrigeration accessories 05-P4 see Evacuating and charging equipment 05-P4 see Refrigeration accessories 06-FB see Tube working tools 0-A see Automatic access valves & fittings 70-0 see Evacuating and charging equipment 75 see Evacuating and charging equipment 7-FA see Tube working tools 444-RC see Refrigeration accessories 5563 see Electronic measurement and control instruments 5860 see Refrigeration accessories 5863 see Refrigeration accessories 5869 see Refrigeration accessories 5870 see Refrigeration accessories 60-FHA see Tube working tools 68 see Electronic measurement and control instruments 6880 see Tube working tools 6-C see Automatic access valves & fittings 70-F-06 see Tube working tools 70-F-08 see Tube working tools 70-F-0 see Tube working tools 70-F- see Tube working tools 70-F-4 see Tube working tools 70-F-6 see Tube working tools 70-F-8 see Tube working tools 7-F see Tube working tools 75-FS see Tube working tools 75-FSC see Tube working tools 75-FSM see Tube working tools 7805 see Tube working tools 7806 see Tube working tools 7806M see Tube working tools 7808 see Tube working tools 7808M see Tube working tools 780 see Tube working tools 780M see Tube working tools 78 see Tube working tools 78M see Tube working tools 784M see Tube working tools 786M see Tube working tools 788M see Tube working tools 780M see Tube working tools 7-C see Automatic access valves & fittings 80-BC see Service manifolds, gauges and charging hoses 80-BC see Service manifolds, gauges and charging hoses 80-BC/47 see Service manifolds, gauges and charging hoses 80-BC/7 see Service manifolds, gauges and charging hoses 80-BC/4 see Service manifolds, gauges and charging hoses 80-BC/447 see Service manifolds, gauges and charging hoses 80-BPC see Service manifolds, gauges and charging hoses 80-BPC see Service manifolds, gauges and charging hoses 80-BPC/40 see Service manifolds, gauges and charging hoses 80-BPC/40 see Service manifolds, gauges and charging hoses 80-BPC/40/7 see Service manifolds, gauges and charging hoses 80-BPC-.0/40 see Service manifolds, gauges and charging hoses 80-G-BC see Service manifolds, gauges and charging hoses 80-G-BC/47 see Service manifolds, gauges and charging hoses 80-G-BC/4 see Service manifolds, gauges and charging hoses 80-G-BC/447 see Service manifolds, gauges and charging hoses 80-G-BPC see Service manifolds, gauges and charging hoses 804-BC see Service manifolds, gauges and charging hoses 804-BC/47 see Service manifolds, gauges and charging hoses 804-BC/7 see Service manifolds, gauges and charging hoses 804-BC/4 see Service manifolds, gauges and charging hoses 804-BC/447 see Service manifolds, gauges and charging hoses 804-BPC see Service manifolds, gauges and charging hoses 804-G-BC see Service manifolds, gauges and charging hoses

20 Part. nr. Pdf file Part. nr. Pdf file Part. nr. Pdf file 804-G-BC/47 see Service manifolds, gauges and charging hoses 804-G-BC/4 see Service manifolds, gauges and charging hoses 804-G-BC/447 see Service manifolds, gauges and charging hoses 804-G-BPC see Service manifolds, gauges and charging hoses 805-BC see Service manifolds, gauges and charging hoses 805-BC/47 see Service manifolds, gauges and charging hoses 805-BC/7 see Service manifolds, gauges and charging hoses 805-BC/4 see Service manifolds, gauges and charging hoses 805-BC/447 see Service manifolds, gauges and charging hoses 805-BPC see Service manifolds, gauges and charging hoses 805-G-BC see Service manifolds, gauges and charging hoses 805-G-BC/47 see Service manifolds, gauges and charging hoses 805-G-BC/4 see Service manifolds, gauges and charging hoses 805-G-BC/447 see Service manifolds, gauges and charging hoses 805-G-BPC see Service manifolds, gauges and charging hoses 8-BC see Service manifolds, gauges and charging hoses 8-BC/47 see Service manifolds, gauges and charging hoses 8-BC/7 see Service manifolds, gauges and charging hoses 8-BC/4 see Service manifolds, gauges and charging hoses 8-BC/447 see Service manifolds, gauges and charging hoses 8-BPC see Service manifolds, gauges and charging hoses 8-BPC/40 see Service manifolds, gauges and charging hoses 8-BPC/40 see Service manifolds, gauges and charging hoses 8-BPC/40/7 see Service manifolds, gauges and charging hoses 8-BPC-.0/40 see Service manifolds, gauges and charging hoses 8-G-BC see Service manifolds, gauges and charging hoses 8-G-BC/47 see Service manifolds, gauges and charging hoses 8-G-BC/4 see Service manifolds, gauges and charging hoses 8-G-BC/447 see Service manifolds, gauges and charging hoses 8-G-BPC see Service manifolds, gauges and charging hoses 84-BC see Service manifolds, gauges and charging hoses 84-BC/47 see Service manifolds, gauges and charging hoses 84-BC/7 see Service manifolds, gauges and charging hoses 84-BC/4 see Service manifolds, gauges and charging hoses 84-BC/447 see Service manifolds, gauges and charging hoses 84-BPC see Service manifolds, gauges and charging hoses 84-G-BC see Service manifolds, gauges and charging hoses 84-G-BC/47 see Service manifolds, gauges and charging hoses 84-G-BC/4 see Service manifolds, gauges and charging hoses 84-G-BC/447 see Service manifolds, gauges and charging hoses 84-G-BPC see Service manifolds, gauges and charging hoses 85-BC see Service manifolds, gauges and charging hoses 85-BC/47 see Service manifolds, gauges and charging hoses 85-BC/7 see Service manifolds, gauges and charging hoses 85-BC/4 see Service manifolds, gauges and charging hoses 85-BC/447 see Service manifolds, gauges and charging hoses 85-BPC see Service manifolds, gauges and charging hoses 85-G-BC see Service manifolds, gauges and charging hoses 85-G-BC/47 see Service manifolds, gauges and charging hoses 85-G-BC/4 see Service manifolds, gauges and charging hoses 85-G-BC/447 see Service manifolds, gauges and charging hoses 85-G-BPC see Service manifolds, gauges and charging hoses 8-BC see Service manifolds, gauges and charging hoses 8-BC/47 see Service manifolds, gauges and charging hoses 8-BC/7 see Service manifolds, gauges and charging hoses 8-BC/4 see Service manifolds, gauges and charging hoses 8-BC/447 see Service manifolds, gauges and charging hoses 8-BPC see Service manifolds, gauges and charging hoses 8-BPC/40 see Service manifolds, gauges and charging hoses 8-BPC/40 see Service manifolds, gauges and charging hoses 8-BPC/40/7 see Service manifolds, gauges and charging hoses 8-BPC-.0/40 see Service manifolds, gauges and charging hoses 8-G-BC see Service manifolds, gauges and charging hoses 8-G-BC/47 see Service manifolds, gauges and charging hoses 8-G-BC/4 see Service manifolds, gauges and charging hoses 8-G-BC/447 see Service manifolds, gauges and charging hoses 8-G-BPC see Service manifolds, gauges and charging hoses 84-BC see Service manifolds, gauges and charging hoses 84-BC/47 see Service manifolds, gauges and charging hoses 84-BC/7 see Service manifolds, gauges and charging hoses 84-BC/4 see Service manifolds, gauges and charging hoses 84-BC/447 see Service manifolds, gauges and charging hoses 84-BPC see Service manifolds, gauges and charging hoses 84-G-BC see Service manifolds, gauges and charging hoses 84-G-BC/47 see Service manifolds, gauges and charging hoses 84-G-BC/4 see Service manifolds, gauges and charging hoses 84-G-BC/447 see Service manifolds, gauges and charging hoses 84-G-BPC see Service manifolds, gauges and charging hoses 85-BC see Service manifolds, gauges and charging hoses 85-BC/47 see Service manifolds, gauges and charging hoses 85-BC/7 see Service manifolds, gauges and charging hoses 85-BC/4 see Service manifolds, gauges and charging hoses 85-BC/447 see Service manifolds, gauges and charging hoses 85-BPC see Service manifolds, gauges and charging hoses 85-G-BC see Service manifolds, gauges and charging hoses 85-G-BC/47 see Service manifolds, gauges and charging hoses 85-G-BC/4 see Service manifolds, gauges and charging hoses 85-G-BC/447 see Service manifolds, gauges and charging hoses 85-G-BPC see Service manifolds, gauges and charging hoses 83-BC see Service manifolds, gauges and charging hoses 83-BC/47 see Service manifolds, gauges and charging hoses 83-BC/7 see Service manifolds, gauges and charging hoses 83-BC/4 see Service manifolds, gauges and charging hoses 83-BC/447 see Service manifolds, gauges and charging hoses 83-BPC see Service manifolds, gauges and charging hoses 83-BPC/40 see Service manifolds, gauges and charging hoses 83-BPC/40/7 see Service manifolds, gauges and charging hoses 85-BC see Service manifolds, gauges and charging hoses 85-BC/47 see Service manifolds, gauges and charging hoses 85-BC/7 see Service manifolds, gauges and charging hoses 85-BC/4 see Service manifolds, gauges and charging hoses 85-BC/447 see Service manifolds, gauges and charging hoses 85-BPC see Service manifolds, gauges and charging hoses 85-BPC/40 see Service manifolds, gauges and charging hoses 85-BPC/40/7 see Service manifolds, gauges and charging hoses 300-CO see Refrigeration accessories 300-CO see Refrigeration accessories 300-FB see Service manifolds, gauges and charging hoses 3-FC see Service manifolds, gauges and charging hoses 3-FC-SP see Service manifolds, gauges and charging hoses 3387 see Refrigeration accessories 339 see Refrigeration accessories 3399 see Refrigeration accessories 3650 see Tube working tools see Refrigeration accessories 3349 see Refrigeration accessories 350-FHA see Tube working tools 360-FHA see Tube working tools 3639 see Fluid control components 3640 see Fluid control components 364 see Fluid control components 364-FH-0 see Tube working tools 364-FH-03 see Tube working tools 364-FHA-04 see Tube working tools 364-FHA-05 see Tube working tools 364-FHA-06 see Tube working tools 364-FHA-08 see Tube working tools 364-FHA-0 see Tube working tools 364-FHA- see Tube working tools 364-FHA-4 see Tube working tools 364-FHA-6 see Tube working tools 364-FHB-04 see Tube working tools 364-FHB-05 see Tube working tools 364-FHB-06 see Tube working tools 364-FHB-08 see Tube working tools 364-FHBM-06 mm see Tube working tools 364-FHBM-08 mm see Tube working tools 364-FHBM-0 mm see Tube working tools 364-FHBM- mm see Tube working tools 3700 see Fluid control components 370 see Fluid control components 370 see Fluid control components 3703 see Fluid control components 3704 see Fluid control components 3706 see Fluid control components 370-FH see Tube working tools 3738 see Fluid control components 375-FS see Tube working tools 380 see Fluid control components 387 see Fluid control components 386 see Fluid control components 383 see Fluid control components 383 see Fluid control components 3836 see Fluid control components 3838 see Fluid control components 3839 see Fluid control components 3840 see Fluid control components 384 see Fluid control components 3860 see Tube working tools see Tube working tools 38760M see Tube working tools see Tube working tools 38770M see Tube working tools 3HDA-0 see Service manifolds, gauges and charging hoses 3HDA-36 see Service manifolds, gauges and charging hoses 3HDA-48 see Service manifolds, gauges and charging hoses 3HDA-60 see Service manifolds, gauges and charging hoses 3HDA-7 see Service manifolds, gauges and charging hoses 3HDCA-36/40 see Service manifolds, gauges and charging hoses 3HDCA-48/40 see Service manifolds, gauges and charging hoses 3HDCA-60/40 see Service manifolds, gauges and charging hoses 3HDCA-7/40 see Service manifolds, gauges and charging hoses 3HDCS-36/40/V see Service manifolds, gauges and charging hoses 3HDCS-60/40/V see Service manifolds, gauges and charging hoses 3HDCS-7/40/V see Service manifolds, gauges and charging hoses 3HDS-36/V see Service manifolds, gauges and charging hoses 3HDS-60/V see Service manifolds, gauges and charging hoses 3HDS6-60 see Service manifolds, gauges and charging hoses 3HDS6-60/V see Service manifolds, gauges and charging hoses 3HDS6-7 see Service manifolds, gauges and charging hoses 3HDS6-7/V see Service manifolds, gauges and charging hoses 3HDS-7/V see Service manifolds, gauges and charging hoses 4090 see Service manifolds, gauges and charging hoses 409 see Service manifolds, gauges and charging hoses 4093 see Service manifolds, gauges and charging hoses 4000 see Evacuating and charging equipment 4000 see Service manifolds, gauges and charging hoses see Evacuating and charging equipment see Service manifolds, gauges and charging hoses see Evacuating and charging equipment see Service manifolds, gauges and charging hoses see Evacuating and charging equipment see Service manifolds, gauges and charging hoses 406-FA see Tube working tools 440-MF see Copper tubes, coils & solder fittings (Inch & Metric) 500A-06 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-08 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-0 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-08 see Copper tubes, coils & solder fittings (Inch & Metric) 500A- see Copper tubes, coils & solder fittings (Inch & Metric) 500A-33 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-4 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-5 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-6 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-8 see Copper tubes, coils & solder fittings (Inch & Metric) 500A- see Copper tubes, coils & solder fittings (Inch & Metric) 500A-8 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-35 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-4 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-54 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-64 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-67 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-70 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-76 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-80 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-89 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-06 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-08 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-0 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-08 see Copper tubes, coils & solder fittings (Inch & Metric) 500A- see Copper tubes, coils & solder fittings (Inch & Metric) 500A-33 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-4 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-5 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-59 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-6 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-8 see Copper tubes, coils & solder fittings (Inch & Metric) 500A- see Copper tubes, coils & solder fittings (Inch & Metric) 500A-8 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-35 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-4 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-54 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-64 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-67 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-70 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-76 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-80 see Copper tubes, coils & solder fittings (Inch & Metric) 500A-89 see Copper tubes, coils & solder fittings (Inch & Metric) 500-CO see Refrigeration accessories 500-FC see Tube working tools 500-FCM see Tube working tools 500-P see Evacuating and charging equipment 500-P see Refrigeration accessories 500-P5 see Evacuating and charging equipment see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) 504- see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) 504- see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric) see Copper tubes, coils & solder fittings (Inch & Metric)