Bowser Baldwin AS-16 Tsunami Digital Sound Decoder Installation Notes
|
|
- Terence Nash
- 6 years ago
- Views:
Transcription
1 Bowser Baldwin AS-16 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-BW1000 digital sound decoder into a Bowser HO Baldwin AS-16. Skill Level 2: The entire installation can be completed in one to two hours with no modification required to the model. Bill of Materials P.N. Description TSU-BW1000 for Baldwin 608A mm x 16mm Oval Speaker Evergreen P.N (1mm) Sheet Styrene For your convenience, Evergreen part numbers have been listed above. Please visit their website at Tools You Will Need 25W Soldering Iron Rosin Core Solder Wire Strippers Wire Cutters Hobby Knife Miniature Screwdriver Set #55 Miniature Drill Bit Pin Vise or Electric Drill Liquid Plastic Cement (TENAX-7R or equivalent) Double-Sided Foam Tape Masking Tape Gauge Wire Metal Straight Edge Dial Calipers
2 Installation 1. To separate the shell from the frame, the shell and the coupler boxes on each end need to be removed. Start by removing the Phillips-head screws holding the box in place on each end. Gently pull the coupler boxes out from each end. (Photo 1) 4. There are four screws holding the factoryinstalled board in place; one in each of the four corners. Remove these and simply lift the board from the model. Remove the remaining black plastic PCB supports and set aside. The longer screws will be reused later. (Photo 4) Photo 4 Photo 1 2. Lift the shell off by gently wiggling it from side to side while lifting from the frame. (Photo 2) 5. Prep the speaker by cutting a small notch in both the front and the back end supports to allow the styrene to rest flush to the speaker frame as shown. (Photo 5 and Figure 1) Photo 5 Photo 2 3. Familiarize yourself with the wiring and label the wires with the masking tape as needed (see the diagram at the end of this document). Cut wires close to the connectors to maintain maximum length. (Photo 3) 1mm Figure 1 1mm Photo 3
3 6. Cut styrene as shown at the end of this document. Cement the four sides to the speaker as shown. Drill two holes using a #55 drill bit for the wires in the end piece nearest the speaker terminals. (Photo 6) 9. Secure the top of the speaker enclosure to fully enclose the baffle. (Photo 9) Photo 9 Photo 6 7. Solder two 4 pieces of purple wire to the speaker terminals, then thread these through the holes drilled in one end of the baffle. (Photo 7) 10. Mount the decoder to the top of the motor with a 1/2 x 3/4 piece of double-sided tape. (Photo 10) Photo 10 Photo 7 8. Using the two longer screws removed in Step 4, mount the speaker to the model using two of the holes along one side. (The mounting holes for the speaker are positioned in such a way as not to allow all four screws to be used.) (Photo 8) 11. Start wiring to the decoder by soldering the right track pickup wires (T-R) to tabs 1 and 10, and left track pickup wires (T-L) to tabs 4 and Solder the motor wires (M+ (yellow) and M- (red)) to tabs 5 and 6. (Photo 11) Photo 11 Photo 8
4 13. Solder the speaker wires to S+ and S-. Since only one speaker is used, polarity is not important. Trim off any excess wire below the tab after soldering to prevent the wires from protruding through the foam tape and to protect against short circuits. (Photo 12) 17. Solder the headlight wires to the headlight tabs. Red is positive and yellow is negative. (Photo 13) Photo Test run the loco to be sure all wiring is correct. Photo Take the loco for a quick test run using address 3. There will be sound and motor control, but no lights. Fix any problems encountered at this time. 19. Tuck any loose wires up and replace the shell. 20. Replace the coupler boxes. 15. Attach the reverse lights to the light tabs. Red is positive and yellow is negative. 16. Trim one of the two red wires from the headlight PCB. These are both positive leads and only one needs to be used.
5 C18 C15 Baffle Dimensions: 11.3mm 11.3mm 14mm 14mm 18mm 16mm 35mm 35mm TSU-BW1000 Wiring Diagram: Front Right Pickup Rear Right Pickup Headlight FRONT F6 F5 S+ S- M- M Backup Light Front Left Pickup Speaker + Speaker - Motor - Motor Motor + Rear Left Pickup New Dimensions in Digital Sound Technology 2014 Throttle Up! Corp. All Rights Reserved 210 Rock Point Drive Durango, CO Phone: (970) Toll Free: Fax: (970) support@soundtraxx.com Website:
Atlas GenSet Tsunami Digital Sound Decoder Installation Notes
Atlas GenSet Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into an Atlas HO GenSet. Skill Level 2: The entire
More informationApplication Note. Con-Cor Goose Tsunami Digital Sound Decoder Installation Notes
Application Note Con-Cor Goose Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-750 Digital Sound Decoder into a Con-Cor HO Goose. Skill Level
More informationBachmann GP7 Tsunami Digital Sound Decoder Installation Notes
Bachmann GP7 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into a Bachmann HO GP7. Skill Level 3: One to three
More informationKato N-Scale E8 Tsunami Digital Sound Decoder Installation Notes
Kato N-Scale E8 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-750 digital sound decoder into a Kato N-scale E8. Skill Level 4: The entire
More informationApplication Note. Atlas B23-7 Tsunami Digital Sound Decoder Installation Notes
Application Note Atlas B23-7 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-1000 digital sound decoder into an Atlas B23-7. Skill Level 2:
More informationAthearn RTR AMD103/P42 Tsunami Digital Sound Decoder Installation Notes
Athearn RTR AMD103/P42 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn HO Ready-To-Roll GE AMD103/P42. Skill Level
More informationApplication Note. Athearn RTR AC4400CW Tsunami Digital Sound Decoder Installation Notes
Application Note Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into an HO Athearn Ready To Roll AC4400CW. Skill Level 2: The entire installation can be completed
More informationApplication Note. Bowser-Stewart VO-1000 Tsunami Digital Sound Decoder Installation Notes
Application Note Overview This application note describes how to install a TSU-1000 Digital Sound Decoder into the Bowser-Stewart VO-1000 Locomotive. Skill Level 4: The entire installation can be completed
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationSection 5 BATTERY REPLACEMENT
u Section 5 BATTERY REPLACEMENT j i 5.1 General The internal battery is used for preserving the clock and programming memory in the models 5000 and 7000. I i The procedure for each is given separately.
More informationPlease read BOTH these Installation Instructions and the General Instructions before attempting to install or operate this equipment.
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationExplorer Wiring Kit (assembled)
Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers
More informationLima XPT/HST Re-Powering Conversion
Lima XPT/HST Re-Powering Conversion Please read through these instructions before beginning the conversion process. Non-Powered Bogie The front non-powered bogie is the starting point for this conversion.
More informationThe Useless Machine. DIY Soldering Edition. Instruction Guide v0004
The Useless Machine DIY Soldering Edition Instruction Guide v0004 TM For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: Soldering
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33380 SIDE S 2007 S2000 Issue Date AUG 2006 PARTS LIST Left upper side strake 2 Grommets 2 Butyl O-rings 2 Washer-screws, 6 x 20 mm
More information2009 Acura TL Installation Instructions
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationStandard Kit #1 (5-way switch)
Standard Kit #1 (5-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationTelecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering tips: Removing Current Wiring: Step 1. Step 2.
Telecaster Wiring Kits Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers Wire Strippers 3/8 Drill Bit 5/32 Drill Bit
More informationWINE DISPENSING SYSTEM MODEL: DYWS4
WINE DISPENSING SYSTEM MODEL: DYWS4 Trim Kit Part Number AWSTK24 INSTALLATION INSTRUCTIONS IMPORTANT: The wine dispensing utilizes a thermo-electric cooling system that can normally cool the bottle bay
More informationStandard Kit #1 (3-way switch)
Standard Kit #1 (3-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationARP AVATAR PATCH PANEL INSTALLATION MANUAL
ARP AVATAR PATCH PANEL INSTALLATION MANUAL Introduction Thank you for purchasing an Avatar Patch Panel Kit! These instructions are intended to guide you through installing and using this kit. Before we
More informationWritten By: Chad Facciolo
HTC One Mini 2 Charging Port Replacement These instructions will show you how to replace your charging port. Written By: Chad Facciolo ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION The charging
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-584) Ford Focus 2000-2007 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationINTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D APPLICATION: F87 M2
INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D330-0026 APPLICATION: 2016-17 F87 M2 Congratulations for being selective enough to use a Dinan Intercooler Upgrade Kit. We have spent many hours
More informationFinish Line Emergency Brake Boot INSTRUCTION SHEET. Part Number. Application: Corvette. Part Includes.
Application: 1997-2004 Corvette Part Includes 1 - Emergency Brake Boot Finish Line Emergency Brake Boot Tools Needed T15 10mm PRE-INSTALLATION NOTES Read completely through instructions to familiarize
More informationG. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead.
G. Building the Cab, Cab Roof and Cab Boiler Extension Page 14 and Backhead. Cab. In order to ensure that the cab and tender would actually look right, as what often appears on a drawing is not always
More informationSuggested Instructions for: , , , C5 Emergency Brake Boot
Suggested Instructions for: 608-348, 608-349, 614-653, 619-200 C5 Emergency Brake Boot Tools Ratchet, 10mm socket, extension #15 Torx screwdriver Needle nose pliers Masking Tape Very small flat head screwdriver
More informationDC Motor. Controller. User Guide V0210
DC Motor Controller User Guide 59757 V0210 This kit provides a great exercise of intermediate soldering skills and creates a device that enables you to control various Pitsco motors, Tamiya gearboxes,
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More informationThe Useless Machine. Parts Only - Build Guide v0001
TM The Useless Machine Parts Only - Build Guide v0001 For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required: One phillips screwdriver,
More informationLP-200 Dummy Load / Wattmeter
LP-200 Dummy Load / Wattmeter Enclosure Retrofit Assembly Instructions March 2009 TelePost Incorporated LP-200 is a trademark of TelePost Inc. Material in this document copyrighted 2009 TelePost Inc. 1
More informationOpenROV. Guide 3 - Electronics. We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV
OpenROV Guide 3 - Electronics We will now move to the assembly of the electronics that will control the ROV. Written By: OpenROV 2017 openrov.dozuki.com Page 1 of 33 INTRODUCTION We will introduce soldering
More informationTriplex Instructions for Packing and Unpacking
2-8-8-2 Triplex Instructions for Packing and Unpacking It is recommended that you review all these instructions before removing the engine or tender from the poly foam container. www.mthtrains.com Table
More information3 Shielded Compact Ribbon (SCR) Wiremount Plug, XX, and Shell Kit, F200-XXX
3 Shielded Compact Ribbon (SCR) Wiremount Plug, 36110-3000XX, and Shell Kit, 36310-F200-XXX Instructions June 2007 78-9100-4282-5 General This instruction manual explains the method of assembling the 3M
More informationBMW E90 Android Touch Screen Radio Installation Instructions
BMW E90 Android Touch Screen Radio Installation Instructions Enjoy your new Android Radio from Bremmen Parts, we appreciate your business. Vibrant Touch Display This radio features a responsive 9 touch
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
2012-15 Hyundai Accent GLS/SE (With Foglights) Attachment Tab Height: 14 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing or operating this
More informationCover Page. Factory Radio Other Documents Available For This Vehicle:
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: Factory Radio with dash radio installation kit 1) Select FLE then PRNT
More informationProf. Steven S. Saliterman Introductory Medical Device Prototyping
Introductory Medical Device Prototyping Department of Biomedical Engineering, University of Minnesota http://saliterman.umn.edu/ You must complete safety instruction before using tools and equipment in
More informationSuper Sky Surfer 2000 Assembly Instructions
Super Sky Surfer 2000 Assembly Instructions Note: Plug and Play version of the Sky Surfer comes with fuselage pre-glued and motor/servos installed. If you wish to route antennas or wires through the tail,
More informationInstallation Instructions For Slider Casement Air Conditioners
Installation Instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationSignal Mirror Installation Instructions Honda Odyssey
Signal Mirror Installation Instructions 2005-2009 Honda Odyssey THE safety accessory of the 21st Century. P/N 210-0122-0 Rev. A4 (6/9/09), BTV 2006 Muth Company, LLC PROFESSIONAL INSTALLATION RECOMMENDED
More informationInstallation tutorial for Console Customs Xbox Mode Dual Button (RFX-5B) Rapid fire Microchip for all Wired and Wireless controllers
Installation tutorial for Console Customs Xbox 360 5-Mode Dual Button (RFX-5B) Rapid fire Microchip for all Wired and Wireless controllers This tutorial is designed to aid you in installation of a console
More informationWiring Techniques for Wiring a Lamp
Supplies and Tools that you will need: Provided in your kit: Polarized lamp plug, 9 of SPT-1 18 AWG parallel lamp cord, bushings and grommets Items that you will need to provide: Phillips screwdriver,
More informationInstallation tutorial for Console Customs Xbox ONE MaxFire ONE V2 PCB
Installation tutorial for Console Customs Xbox ONE MaxFire ONE V2 PCB This tutorial is designed to aid you in installation of a console customs MaxFire ONE V2 Circuit board in the newer Xbox One Controllers
More informationOpen Air. Kit includes: Drawer Full Indicator board assembly, (2) retainers, and (4) screws. PREPARATION
Open Air Installation Video You will need: 8-inch #2 Phillips screwdriver Needle-nose pliers DFI INSTALLATION GUIDE For installation videos, visit the Customer Service playlist at www.youtube.com/user/thelitterrobot
More informationWARNING. BX Ford Explorer With Adaptive Cruise Control & Eco Boost Installation Instructions
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationAssembly and Installation Instructions for White Oak Audio Design PL400 Series 1 LED board
Thank you for purchasing White Oak Audio Design s Phase Linear PL400 Upgrade LED Light Board. White Oak Audio Design products are meticulously engineered and tested to ensure a direct drop in fit with
More informationBX3615. Subaru Impreza WRX (Include STI) Subaru 2012 Impreza Premium 2010 Outback Sport Installation Instructions Attachment Tab Height: 15
1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who are familiar with our products and have the equipment and knowledge necessary to do fit work. If needed, Blue
More informationInstallation Instructions
Please read through these instructions completely prior to attempting any installation www.hsiheadwalls.com Installation Instructions Installation Instructions Tel: 925.427.7800 Fax: 925.427.0800 support@hsiheadwalls.com
More informationInstallation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions)
Installation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions) This tutorial is designed to aid you in installation of a console customs
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 13 Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing or operating this equipment. Serial Number 1. Blue Ox towing products and accessories
More informationiphone 4S Dismantling Instructions
iphone 4S Dismantling Instructions These instructions will show you how to open the iphone to replace the digitizer, LCD screen and other internal parts. Opening your iphone will void your warrantee, and
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2005-2010 Chevy Corvette C6 THE safety accessory of the 21 st Century. P/N 210-0144-0 Rev. A3 (9/29/2011), BTV 2007 Muth Mirror Systems, LLC Page 3 of 10PplPage
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 16-1/4 Attachment Tab Width: 21-3/4 Please read BOTH these and the General Instructions prior to installing or operating this equipment. Serial Number 1. Blue Ox towing products
More informationSignal Mirror Installation Instructions Toyota Tacoma
Signal Mirror Installation Instructions 2005-2015 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0115-0 Rev. A4 (3/11/15), BTV 2005 Muth Mirror Systems, LLC Page 3 of 12PplPage 3 of 12
More informationPeter Madsen installs a DCC Sound decoder.
Peter Madsen installs a DCC Sound decoder. At Malkara I bought myself a very cheap ($295) noisy C3528 from Austrains and in the process I was offered a black roundtop C3601 at I price I couldn t refuse
More informationThe ability to make basic voltage and resistance measurements using a digital multimeter
Congratulations on your purchase of a new OneShot chassis! The PC01 OneShot combines a rugged enclosure, power supply, and discrete instrument DI in a compact 1/4U package. A few minutes of assembly are
More informationPlease read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment.
Serial Number 2012 Hyundai Accent (No Foglights) Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories
More informationTCS Book of Classic N Installations v1.21 A simple guide to installing Classic N Decoders
TCS Book of Classic N Installations v1.21 A simple guide to installing Classic N Decoders CN CN-GP To use this installation book, first read through the generic installation. Next, find the specific locomotive
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
(No Turbo) Attachment Tab Height: 14 Serial Number Attachment Tab Width: 18 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products
More informationWARNING Mercedes Smart for two CDI Installation Instructions BX1990. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationRefer to the drawing on page 2 to familiarize yourself with the connectors and controls on the
PT Boat Sound by CAUTION: This device can be damaged by static discharge. Please exercise care during installation to avoid this possibility. Discharge yourself to an electrical ground (outlet cover screw
More informationinstallation instructions For Slider Casement Air Conditioners
installation instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT
More informationInstructions: GSC 60 Flatcar Kit with or without bulkheads Tangent Part Number: and /2016
Instructions: GSC 60 Flatcar Kit with or without bulkheads Tangent Part Number: 11000-01 and 11000-02 5/2016 Thank you for purchasing the Tangent Scale Models GSC 60 Flatcar Kit! A few quick notes before
More informationHTC One Mini 2 Battery Replacement
HTC One Mini 2 Battery Replacement Replace the battery in your HTC One Mini 2 Geschreven door: Jeron Hogan ifixit CC BY-NC-SA nl.ifixit.com Pagina 1 van 10 GEREEDSCHAPPEN: 64 Bit Driver Kit (1) ifixit
More informationI Click on a link tab to jump to that page. Cover Page
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: 1) Select FLE then PRNT and select your printer. 2) n the print options
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-665) Ford Crown Victoria, Mercury Grand Marquis 1992-2010 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint
More informationInstructions for Building the Pulsed Width Modulation Circuit. MC-12 (DC Motor Controller or PWM) From Electronic Light Inc. (revised kit 10/03/08)
Instructions for Building the Pulsed Width Modulation Circuit MC-12 (DC Motor Controller or PWM) From Electronic Light Inc. (revised kit 10/03/08) Congratulations on your purchase of the MC-12 DC Motor
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Honda CRV 1997-2003 THE safety accessory of the 21 st Century. P/N 210-0032-0 Rev B2 (6-26-04), GG 2003 Muth Mirror Systems, LLC. Note: Professional Installation
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationInstallation tutorial for Console Customs PS3 TrueFire Standard Rapid fire Microchip for Sixaxis and Dualshock 3 controllers
Installation tutorial for Console Customs PS3 TrueFire Standard Rapid fire Microchip for Sixaxis and Dualshock 3 controllers This tutorial is designed to aid you in installation of a console customs rapid
More informationWARNING! ETCHED PARTS CONTAINED IN THIS KIT HAVE SHARP POINTS, EDGES AND CORNERS.
MPD18 chassis build instructions K A (see below for details) J I G H L C D F E B M Parts list: Ident Quantity A Etched Nickel/Silver fret 1 B Wheel sets 2 C Worms 2 D Worm gears 2 E Shaft adapters 2 F
More informationElektor Construction Guide TAPIR
Elektor Construction Guide TAPIR The TAPIR is a three-dimensional assembly. To ensure good access to all soldering points, we recommend assembling the kit exactly according to the described sequence. 1
More informationKN-8828B Upgrade Directions
KN-8828B Upgrade Directions This document outlines the steps to take to update earlier Hottop Bean Roasters to the KN-8828B 2007 by Chang Yue and Hottop USA - All Rights Reserved No part of this document
More informationFig. 1 Fig. 2. Fig. 3 Fig. 4 TOOLS REQUIRED: *Phillips Screwdriver *Three Inch Putty Knife*Panel Removal Tool *10mm Nut Driver CONTENTS:
*Phillips Screwdriver *Three Inch Putty Knife*Panel Removal Tool *10mm Nut Driver CONTENTS: 2EA. 6X9 TWO WAY SPEAKERS P/N 05030281AA 1EA. INSTRUCTIONS P/N RBI05LXREAR 300c and Charger 1. Remove the lower
More informationInstallation Manual MODEL NE-42
Installation Manual MODEL NE-42 GET TO KNOW YOUR UNIT 1 1. CROSS BRACES - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with 1/4 & 1/8 drill bit)
More informationBUILD YOUR OWN. Pack 22
BUILD YOUR OWN TM Pack 22 01 CONTENTS Assembly Guide 339 Stage 70: The front brake lever Stage 71: The oil hose and the twistgrip Stage 72: Fitting the front fork assembly Editorial and design by Continuo
More informationThe Empeg and Riōcar Illumination Kit Installation and User s Manual
The Empeg and Riōcar Illumination Kit Installation and User s Manual Last Updated: October 13, 2005 Table of Contents READ THIS FIRST!!!...1 Introduction to the Installation Process...3 Install the Hijack
More informationKASTLE v1.5 - Assembly Guide
last update: 14. 12. 2017 KASTLE v1.5 - Assembly Guide bastl-instruments.com INTRODUCTION Welcome to the assembly guide for the Kastle kit - mini modular synthesizer. It is suitable for beginners. It is
More informationMODIFICATION OF THE BOWSER TRACTION TRAILING TRUCK
MODIFICATION OF THE BOWSER TRACTION TRAILING TRUCK August 16, 2007 Shortly after the Bowser 125100 series of HO scale traction drive mechanisms were introduced in 1999, members of the Southern California
More informationINSTALLATION MANUAL REAR PARKING ASSIST SENSORS
MITSUBISHI MOTORS GENUINE ACCESSORIES PART NUMBER MZ380456EX APPLICABLE MODEL LANCER SEDAN INSTALLATION MANUAL REAR PARKING ASSIST SENSORS Thank you for purchasing MITSUBISHI genuine * REAR PARKING ASSIST
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
2014-15 Chevy Malibu (3LT/1LTZ/2LTZ) (No Active Shutter or E-Assist) Attachment Tab Height: 12-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Instructions prior to installing
More informationBuilding the Toothpick Audio CW Filter
Building the Toothpick Audio CW Filter Introduction The toothpick is a simple variable bandpass audio filter designed to compliment the Splinter QRPp Trans-Receiver. The filter also contains an audio amplifier
More informationGMC - Jimmy Chevy - S-10 / S-15 Series Olds - Bravado
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. & nstall Factory
More informationWARNING Mercedes Benz GL550 4Matic Installation Instructions BX1992. Serial Number
Please read BOTH these and the General Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationX5 License Plate PDC Retrofit (Part # ) dkl
X5 License Plate PDC Retrofit (Part # 66 21 0 416 597) dkl Disclaimer: This article is only intended to be use as a guideline in addition to those instructions provided by BMW. As with all modifications,
More informationI Click on a link tab to jump to that page. Cover Page
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
(No Turbo) Attachment Tab Height: 14 Serial Number Attachment Tab Width: 18 Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products
More informationInstructions: PS-2CD 4000 Model Kit Revised 7/2008
Instructions: PS-2CD 4000 Model Kit Revised 7/2008 Plastic Parts included: Body shell Parts Sprue #1 Roof, trainline, gravity outlet gates, and centersill/endsill pieces Parts Sprue #2 Underframe bolster
More informationWARNING. BX Dodge Durango. Serial Number
Please read BOTH these Installation Instructions and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be
More informationBMW E39/E53 Android Touch Screen Radio Installation Instructions
BMW E9/E5 Android Touch Screen Radio Installation Instructions Enjoy your new Android Radio from Bremmen Parts, we appreciate your business. Vibrant Touch Display This radio features a responsive 9 touch
More informationWARNING. BX Ford Explorer With Adaptive Cruise Control & Eco Boost Installation Instructions. Bolt Torque Specifications
Please read BOTH these and the General Instructions before attempting to install or operate this equipment.. Blue Ox towing products and accessories are intended to be installed by Blue Ox Dealers who
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
2012-14 Chevy Captiva Sport Attachment Tab Height: 21-1/2 Serial Number Attachment Tab Width: 18-1/2 Please read BOTH these and the General Instructions prior to installing or operating this equipment.
More informationBX2520 Installation Instructions 2004 Mazda 3
BX2520 Installation Instructions 2004 Mazda 3 Serial No. The headlight assembly, front fascia, horn bracket and windshield washer reservoir are removed for baseplate installation. Drilling is required.
More informationMM Strut Tower Brace, GT (MMSTB-5.1)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Strut Tower Brace, 1996-97 GT (MMSTB-5.1) MMSTB-5.1 is for 1996-97 GT s with
More informationWARNING BX1514. Serial Number Buick LaCrosse Installation Instructions
Serial Number Please read BOTH these and the General Towing Instructions before attempting to install or operate this equipment. 1. Blue Ox towing products and accessories are intended to be installed
More informationTip: 3425 Kittle with LokSound Micro V4.0 Conversion and LED Lighting Date:
Hi All, Ed Lekanides sent me this article where he used a LokSound Micro V4.0 decoder to convert his Kittle. He shows what he had to do differently to my original article to complete the conversion. My
More informationAssembly and Installation Instructions for White Oak Audio Design TM-1001 LED board
Thank you for purchasing White Oak Audio Design s TM-1001 Upgrade LED Light Board. White Oak Audio Design products are meticulously engineered and tested to ensure a direct drop in fit with your tuner.
More informationKX2 Side KX installation
KX2 Side KX installation NOTE: The installation of any Side KX parts does NOT require the unsoldering of any connection nor removal of ANY of the boards from within the radio! The user/installer assumes
More information