MIX SUITE + VOCAL BOOTH BASICS

Size: px
Start display at page:

Download "MIX SUITE + VOCAL BOOTH BASICS"

Transcription

1 MIX SUITE + VOCAL BOOTH BASICS Written/produced by FVNMA Technical Staff at the School of the Art Institute of Chicago, rev. 1/2/13 GROUND RULES: 1. ABSOLUTELY NO FOOD OR DRINK IN THE ROOM! 2. NEVER TOUCH THE PROJECTION SCREEN AT THE FRONT OF THE ROOM. 3. THE ACOUSTICAL PANELS AND DIFFUSERS ON THE WALLS ARE FRAGILE AND VERY EXPENSIVE--DON T TOUCH THEM! 4. FINALLY, PLEASE DON T RECONFIGURE ANY OF THE CABLES IN THIS ROOM. IF YOU ENCOUNTER PROBLEMS, CONTACT THE FVNM TECH OFFICE AT ROOM POWERING UP In order to prevent speakers from popping and to ensure that all components properly sync up, it s important that everything be turned on IN THIS PRECISE ORDER: 1. Turn on the Furman Power Conditioner at the top right corner of the mixing desk. 2. If you re planning to record talent via mics in the Mix Suite or the Vocal Booth, turn on the AVID PRE mic preamp unit on the floor to the right of the mixing desk. 3. Press the power BUTTON on the MAGMA HD (big black box on the lower left side of the mixing desk) until its green power light turns on. Wait seconds for the Magma to warm up. 4. Turn on the other Furman Power Conditioner at the top left corner of the mixing desk. The D- Command mixing console should power on and light up. 5. Press the power buttons on the 192 and SYNC I/O interfaces (top right side of the mixing desk). 6. Press the power button on the XMON unit just below the 192 and SYNC I/O interfaces. 7. Power on the Smart Rack at the back of the room via the switch located on the right side of the Furman power conditioner (just above the laptop input/cable). Press the Standby button on the lower left of the Outlaw audio receiver to turn it on. If you are using the Projector turn it on. 8. Lastly turn on the Mac Pro under the mixing console. * NOTE: before you leave, turn everything off in the exact order laid out on page 9! (1)

2 1413's Smart Rack is similar to those in other classrooms: it has a row of buttons that you can use to select different inputs to the projector, and to turn on the projector. Note: the volume knob on the Smart Rack controls the volume levels of other inputs (Blu-Ray, laptop) but does not correspond to ProTools--your audio output from ProTools is controlled at the Mixing Desk and by the Outlaw receiver. 8. Press the PC button on the Smart Rack until the black Outlaw Audio receiver reads 7.1CH DIRECT (you might have to press the button twice). Adjust the volume dial on the receiver to make sure it reads 0 db. Look for the red speaker icon on the receiver s LED display--if you don t see it, hold down the mute button until it appears. 9. Turn on the power switches (located on the backside of each speaker) of the two Dynaudio monitors (just behind the mixing desk). LAUNCHING PRO TOOLS 1. First, create a folder on the AUDIO_HD1 or AUDIO_HD2 drives and label it with your name. 2. Click the ProTools 10 icon in the Dock (left side of screen) to launch the program. Choose Create Blank Session from the options in the Quick Start window. Click the triangle to reveal Session Parameters. (2)

3 3. Set up your session as follows: It s very important that you choose USE THESE under I/O Settings. This ensures that the inputs and outputs in your session correspond to the equipment in the mix suite. 4. Name your session and save it to the folder you created in step 1. UPDATING AN EXISTING SESSION Follow these instructions to update a session from another facility (e.g. room MC324) or from an earlier version of Pro Tools for use in the Mix Suite. 1. Copy the session from your hard drive to your folder on the AUDIO_HD1 or AUDIO_HD2 drives. 2. Open the session. You will see a dialog with some variation of the one pictured here. Take a moment to read the dialog and choose the option that selects the current playback engine with 4 DSP and 64 Voices. (3)

4 If you used plug-ins in your session that are not on the Mix Suite computer (or are an earlier or otherwise incompatible version) you will get a message like the one pictured here. Click Yes for a detailed list of the plug-ins and settings that will not carry over to your new session. Otherwise click No to continue. Your session will now open. Save a copy in your folder. 3. A message might appear that Your hardware does not have sync. If so, designate the Mix Suite s SYNC unit as the session s clock source. Select Session from the Setup menu. In the Session Setup window, make sure that SYNC is selected for Clock Source and choose Internal/VSO under Clock Reference. The Locked rectangle will turn to a solid green. 4. Go to the Setup Menu and choose Playback Engine. The settings shown here were recommended by an Pro Tools engineer for optimum performance with the particular hardware and software setup in the Mix Suite. You can adjust them as need be (e.g. add more voices) but these settings are a good place to start. (4)

5 5. The most potentially complicated part of migrating a session to the Mix Suite involves the Input/Output Setup. As of Fall 2013, the Mix Suite offers the ability to mix in 7.1 surround sound* and the I/O Setup has changed accordingly. Compared to previous versions of Pro Tools, Pro Tools 10 seems to do a fine job of automatically updating a session to the latest I/O Setup saved on the Mix Suite computer, but you should follow the steps below to ensure that your session is fully and correctly utilizing the updated hardware/software setup. * Most corporate movie theaters feature 7.1 audio, as do the majority of new home theater entertainment systems. However, the Gene Siskel Film Center does NOT currently support 7.1 surround sound--it is a 5.1 facility. See page 6 for instructions on setting up your session for 5.1 surround. Choose I/O Setup from the Setup menu. Click the Input tab. The settings should appear as shown here. Click the Output tab at the top of the window and confirm that 7.1 OUT is the Output path, as shown above. Click the Bus tab. Things can get a bit more complicated at the Bus tab. If you are updating from another facility, you will probably not need to follow all of the steps outlined here. However, if you are updating a session that was created in the Mix Suite with an earlier version of ProTools and you ve done any kind of volume and pan automation, you ll need to keep the old I/O settings as you enable the new settings. The scenario shown here uses a Pro Tools 9 session that was created in the Mix Suite. We need to Import the new I/O Bus settings and disable the old settings without deleting them. Click the Import Settings button. (5)

6 Pro Tools will automatically navigate to its IO Settings folder. Choose USE THESE and click Open. Uncheck all output paths other than 7.1 OUT The Bus path labeled 5.1 at the top of the list and the line out 4 paths are from an earlier version of Pro Tools. Uncheck the boxes for any Channel output paths other than 7.1 OUT at the bottom of the list. You can leave buses 1-2, 3-4, etc. checked. When you click OK, you might get this prompt: Before closing the window, we ll need to change the Audition Paths and Default Output Bus--select 7.1>7.1 OUT for each. To fix this, you ll need to rename your old/disabled paths/subpaths so that none of them have the same name as any of your new paths/subpaths. In the example shown here, 5.1 is renamed OLD 5.1. When you click OK, the I/O settings are confirmed and you can move on from this window! 5. Finally, you ll need to remap all of your tracks outputs to the Mix Suite s outputs. Hold the option key (this performs the action on all tracks) and click on any track s output pop-up. Select 7.1 OUT. Stereo to output all tracks to a standard stereo left and right output path. Selecting 7.1 OUT gives you the ability to output a track to any of the speakers. Use 7.1 OUT 5.1 for a standard Gene Siskel Film Center compatible surround mix. (6)

7 AUDIO MONITORING To monitor from the main speaker system (in 5.1 or stereo), choose Main on the Inputs bus. To choose the Dynaudio nearfield monitors, press Mini (also on the Inputs bus). To monitor using headphones, press the Phones button in the Cues bus, then press On. If you don t hear anything, press Source until the LED panel reads HP Mn. This room has been calibrated so that when the Main output level is turned almost all the way up and reads as CR -21 on the LCD display, you are hearing your audio at the approximate level of a commercial movie theater. Headphones On Main Mini (If you don t hear any sound, it might be because this Mute button is activated) IMPORTING & MONITORING VIDEO Go to the File menu and scroll down to Import> Video... This Video Import Options window will appear: Choose New Track as your Destination and Session Start as Location. If your video clip has audio that you d like to include in your session, check Import audio from file. You can view your video clip as a separate window on one of the two computer monitors, or you can send it to the projector (which also sends the signal to the TV in the Vocal Booth).* Choose BLACKMAGIC as your input on the Smart Rack and make sure the audio is set to 7.1 CH DIRECT. If not, press the BLACKMAGIC button again. To view video on the projector and in the Vocal Booth choose Video out PCIe from the Options menu (make sure the option is checked). *It s now possible to use 1080p ProRes HD video with this system. However, for optimal performance use a lower resolution video reference file, e.g. use MPEG Streamclip to compress to 720p with a Quality setting of 50%. (7)

8 USING THE VOCAL BOOTH Room 1414 contains the sound-proofed Vocal Booth. The booth is made of sound-deadening boards, acoustic foam and fabric to insulate against environmental noise on the 14th floor (including from the HVAC system that has been known to impede the recording process in the Mix Suite). You can record directly to a laptop or other audio-recording device in the Vocal Booth without using the Mix Suite, but if you re interested in recording from the V.B. directly to a ProTools session via the AVID PRE mic pre-amp, you ll need to follow the steps below. 1. Reset the PRE pre-amp. Go to the Setup menu and choose Peripherals, then click on the Mic Preamps tab. Click the reset button to reset the levels and settings for all of PRE s inputs. 2. Go to the I/O Setup window (from the Setup menu), click on the Mic Preamps tab and make sure that PRE #1 is activated as shown here. 3. From the 'View menu go to Edit Window Views and select Mic Preamps. Each track will now show controls for the PRE unit. 4. Create a new Audio track via the Track menu (or Command-Shift-N). Note the controls below. *Click here to set the track height *click this Input Selector to open a popout gain fader: * use the popout fader to adjust the gain of the mic input * Track Input Monitor * you will not hear anything from the mic connected to the input unless you click this * Record Enable Audio Input Path Selector * select any of 8 PRE inputs-- inputs 1-4 are routed from cables in the Vocal Booth * Track Volume * you might want to raise this so that your talent can hear him/herself adequately, note that this is NOT the same as raising the mic input gain * Phantom Power Selector * click and drag down to 48v to enable phantom power if the mic requires it * If you ve selected any of the first four PRE inputs you can record from the Vocal Booth. The mic stands in the Vocal Booth are set up with pop filters and clips to be used with Neumann U87 mics. There are four advanced mic kits at the Media Center--each contains a U87 mic and windscreen (for additional sibillance protection) and a set of Sony MDR-7506 headphones. Turn on the light in room 1414 so you can see inside the Vocal Booth, then turn on the power strip on the floor of the booth. The booth s three light strips should come on. To monitor video from ProTools via the booth s TV (after choosing Video out PCIe from ProTools Options menu), press the orange button on the TV until it turns blue. To see the video simultaneously on the projector in 1413, press Mojo on the Smart Rack switcher. (8)

9 Power Switch Master Volume Output Level Plug headphones into any of the six OUT inputs on the headphone amp (don t plug into the first jack that says DIRECT IN ) and use the MASTER VOLUME and LEVEL knobs plus the EQ knobs on each output to adjust the signal you re receiving from ProTools. 1. To send audio from ProTools to the Vocal Booth, press the Studio LS button in the cues panel and use the Level knob below it to adjust the output level. 2. To communicate with talent in the Vocal Booth, use the Internal Talkback mic built into the D-Command console. First, press the button labeled Internal and the Asgn TB button and On buttons in the cues panel. 3. Press the Sel Source button until the display reads ST MN. Depress the TALK BACK button (just to the left of the transport buttons) to activate the talkback mic. Adjust the send level from ProTools to the Vocal Booth. Adjust the talkback mic level via the Talkback Level knob. POWERING DOWN 1. Turn off the Dynaudio nearfield monitors, the Outlaw receiver and the video projector (via the Smart Rack DISPLAY OFF button) and the Furman power conditioner. NO BLUE SCREEN! 2. Turn off the XMON interface. 3. Shut down the Mac Pro--wait until it s completely shut down before continuing! 4. Press the power buttons on the 192 and SYNC I/O interfaces. 5. Turn off the D-Command via the Furman Power Conditioner at the top left of the mixing desk. 6. Turn off the Magma HD on the left side of the mixing desk. 7. Turn off the AVID PRE mic preamp. 8. Turn off the Furman Power Conditioner at the top right corner of the desk. 9. Turn off the power strip and lights in the Vocal Booth and the lights in the Mix Suite. (9)

MC1413 ADV. MIX SUITE STARTUP GUIDE. Ground Rules

MC1413 ADV. MIX SUITE STARTUP GUIDE. Ground Rules MC1413 ADV. MIX SUITE STARTUP GUIDE Ground Rules 1. absolutely no food or drinks in the Mix suite 2. never touch the projection screen in front of the room 3. the acoustical panels and diffusers on the

More information

MP212 Principles of Audio Technology II

MP212 Principles of Audio Technology II MP212 Principles of Audio Technology II Lab #2 DM2000 and Pro Tools Version 3, 06/07/2012 revised AR, previous versions: JMC, JL Version 4, 09/15/2013 revised AR Copyright 2007 Berklee College of Music.

More information

User Guide (Clarett USB Edition)

User Guide (Clarett USB Edition) User Guide (Clarett USB Edition) Version 1.0 www.focusrite.com TABLE OF CONTENTS INTRODUCTION... 3 System Requirements....4 Software Installation...4 The Clarett USB Mixer basic principles...5 MIXING &

More information

Berklee College of Music: MTEC224 Digital Audio Basics/Systems LAB #4 Created by JAL Created on 11/22/06 4:54 AM Page 1 of 6

Berklee College of Music: MTEC224 Digital Audio Basics/Systems LAB #4 Created by JAL Created on 11/22/06 4:54 AM Page 1 of 6 MTEC-224 Lab #4 Working with Audio and Video In this Lab, you will load music and sound effects from the DA-88 into ProTools, and align them to picture from a video tape. The materials for this Lab consist

More information

New for Pro Tools 9. Pro Tools HD Native vs Pro Tools HD Hardware

New for Pro Tools 9. Pro Tools HD Native vs Pro Tools HD Hardware New Pro Tools HD Series interfaces, including the HD I/O, HD Omni, Sync HD, HD MADI, and Pre, were introduced in 2010 along with the Pro Tools HD Native system. The Pro Tools HD Native PCIe card enables

More information

Apogee Ensemble Thunderbolt Audio Interface

Apogee Ensemble Thunderbolt Audio Interface Apogee Ensemble Thunderbolt Audio Interface Quick Start Guide Fall 2014 Contents Overview... 3 Introduction...3 Package Contents...4 Ensemble Product Tour...6 Getting Started... 8 System Requirements...8

More information

Gassmann Studio Tutorial

Gassmann Studio Tutorial Gassmann Studio Tutorial This document discusses some scenarios for using the Gassmann Studio successfully, and some troubleshooting tips for when things are not so successful. This document has no table

More information

Setting up Pro Tools I/O & connecting a microphone for Recording

Setting up Pro Tools I/O & connecting a microphone for Recording Setting up Pro Tools I/O & connecting a microphone for Recording The purpose of this lab is to demonstrate the ability to correctly connect a microphone to the Fast Track Pro interface in such a way that

More information

AUDIO INSTRUCTIONS CAPTURE STUDIO ONE PRO TOOLS

AUDIO INSTRUCTIONS CAPTURE STUDIO ONE PRO TOOLS AUDIO INSTRUCTIONS CAPTURE STUDIO ONE PRO TOOLS Updated 4/1/2016 SETTING UP THE LIVE ROOM Set the room up for recording. Arrange the studio rug in the live room and position microphone stands or direct

More information

Getting Started. Pro Tools LE & Mbox 2 Micro. Version 8.0

Getting Started. Pro Tools LE & Mbox 2 Micro. Version 8.0 Getting Started Pro Tools LE & Mbox 2 Micro Version 8.0 Welcome to Pro Tools LE Read this guide if you are new to Pro Tools or are just starting out making your own music. Inside, you ll find quick examples

More information

MXL USB.006.

MXL USB.006. MXL USB.006 www.mxlmics.com Congratulations on your purchase of the MXL USB.006 which uses a large 32mm gold diaphragm capsule for added warmth. MXL microphones are the result of world-class engineering

More information

Studio D/E User s Guide

Studio D/E User s Guide Studio D/E User s Guide Studio D and E offer eight-channel surround playback as well as recording and playback from both Macintosh and Linux computers. The studios feature Yamaha DM-1000 mixers that allow

More information

USB Microphone. Marshall Electronics

USB Microphone. Marshall Electronics USB Microphone Marshall Electronics Warranty Marshall microphones are guaranteed against defects in material and workmanship for one year from date of purchase. Should you encounter any problem with this

More information

Apogee Ensemble Thunderbolt Audio Interface

Apogee Ensemble Thunderbolt Audio Interface Apogee Ensemble Thunderbolt Audio Interface Quick Start Guide July 2017 Contents Overview... 3 Introduction...3 Package Contents...4 Ensemble Product Tour...6 Getting Started... 8 System Requirements...8

More information

M-Powered Basics Guide

M-Powered Basics Guide M-Powered Basics Guide Version 6.8 for M-Powered Systems on Windows or Macintosh Digidesign 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA tel: 650 731 6300 fax: 650 731 6399 Technical Support

More information

Mbox Basics Guide. Version 6.4 for LE Systems on Windows XP and Mac OS X. Digidesign

Mbox Basics Guide. Version 6.4 for LE Systems on Windows XP and Mac OS X. Digidesign Mbox Basics Guide Version 6.4 for LE Systems on Windows XP and Mac OS X Digidesign 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA tel: 650 731 6300 fax: 650 731 6399 Technical Support (USA)

More information

Mic Mate Pro. User Manual

Mic Mate Pro. User Manual R Mic Mate Pro User Manual Mic Mate Pro Features Congratulations and thank you for purchasing the MXL Mic Mate Pro. This device is designed to minimize your setup for recording and allow for professional

More information

Getting Started Pro Tools M-Powered. Version 8.0

Getting Started Pro Tools M-Powered. Version 8.0 Getting Started Pro Tools M-Powered Version 8.0 Welcome to Pro Tools M-Powered Read this guide if you are new to Pro Tools or are just starting out making your own music. Inside, you ll find quick examples

More information

TEMPO USB MICROPHONE

TEMPO USB MICROPHONE TEMPO USB MICROPHONE Congratulations on your purchase of the MXL Tempo USB microphone. MXL microphones are the result of worldclass engineering and manufacturing capabilities. They are designed to provide

More information

USB.007 Studio Quality USB Stereo Condenser Mic. User Manual

USB.007 Studio Quality USB Stereo Condenser Mic. User Manual USB.007 Studio Quality USB Stereo Condenser Mic User Manual Congratulations on your purchase of the MXL USB.007 which uses two gold diaphragm capsules in an X/Y pattern for stereo recording. MXL microphones

More information

Getting Started. Pro Tools LE & Mbox 2 Pro. Version 8.0

Getting Started. Pro Tools LE & Mbox 2 Pro. Version 8.0 Getting Started Pro Tools LE & Mbox 2 Pro Version 8.0 Welcome to Pro Tools LE Read this guide if you are new to Pro Tools or are just starting out making your own music. Inside, you ll find quick examples

More information

MP212 Principles of Audio Technology II

MP212 Principles of Audio Technology II MP212 Principles of Audio Technology II Lab # 3 Mixing in ProTools Version 2.0, 11/05/06 revised JMC, JL, JB Version 4, 06/11/12 revised AR Version 6.1 (X48), 11/26/2013 revised AR Copyright 2006 Berklee

More information

BBGUNN s Allen and Heath ZED R16 setup guide for Reaper

BBGUNN s Allen and Heath ZED R16 setup guide for Reaper BBGUNN s Allen and Heath ZED R16 setup guide for Reaper So you ve bought or are thinking of buying an Allen and Heath Zed R16 and are wondering how to make it work with Reaper. Well, you ve come to the

More information

Intro to Pro Tools. Pro Tools LE and Eleven Rack. Version 8.0.1

Intro to Pro Tools. Pro Tools LE and Eleven Rack. Version 8.0.1 Intro to Pro Tools Pro Tools LE and Eleven Rack Version 8.0.1 Welcome to Pro Tools LE and Eleven Rack Read this guide if you are new to Pro Tools or are just starting out making your own music. Inside,

More information

M-16DX 16-Channel Digital Mixer

M-16DX 16-Channel Digital Mixer M-16DX 16-Channel Digital Mixer Workshop Using the M-16DX with a DAW 2007 Roland Corporation U.S. All rights reserved. No part of this publication may be reproduced in any form without the written permission

More information

Contents. Saffire PRO 10 i/o. User Guide. Changes to Version 1. Additional Info. Hardware Monitoring Digital Output Monitoring...

Contents. Saffire PRO 10 i/o. User Guide. Changes to Version 1. Additional Info. Hardware Monitoring Digital Output Monitoring... Contents Hardware Monitoring... 2 Digital Output Monitoring... 3 Digital Inputs and Sync Source Selection... 3 Changes to Version 1 Using Multiple Units on a PC... 3 Additional Info Setting up Multiple

More information

Seeley Mudd 116 Audio Production Studio

Seeley Mudd 116 Audio Production Studio Reservations: 1. Check the Calendar on the Studio Webpage to see available studio times. 2. Look over the Equipment List to decide what equipment you ll need. 3. Fill out the Studio Reservation Form from

More information

Zero Latency and Tape Style Monitor Handbook

Zero Latency and Tape Style Monitor Handbook What is "Z" monitoring? Zero Latency or Direct ing via ASIO 2.0 is somewhere between 2-5ms. So is that good enough when monitoring or overdubbing a live performs? Well it depends on the person. Vocals

More information

Making a Recording in the Booth

Making a Recording in the Booth Making a Recording in the Booth From UW Phonetics/Sociolinguistics Lab Wiki This page is a quick start guide to making a recording in the soundproof booth. Before continuing with the guide, check to ensure

More information

Recording and mixing with the DM-24 and Digi 001

Recording and mixing with the DM-24 and Digi 001 Recording and mixing with the DM-24 and Digi 001 The combination of the TASCAM DM-24 and the Digi 001 make for a very powerful system. While the 001 provides 32 audio tracks in Pro Tools and audio I/O,

More information

IMA DIGITAL AUDIO LAB HARD DISC RECORDING

IMA DIGITAL AUDIO LAB HARD DISC RECORDING IMA DIGITAL AUDIO LAB HARD DISC RECORDING Pro Tools LE Information Sheet Start Up Procedure Turn on main power switch for audio system, as usual Next, turn on the computer. This will also turn on ProTools

More information

How to Present External Audio Stimuli from PC - Focusrite Soundcards using the Aurical Aud Audiometer

How to Present External Audio Stimuli from PC - Focusrite Soundcards using the Aurical Aud Audiometer How to Present External Audio Stimuli from PC - Focusrite Soundcards using the Aurical Aud Audiometer This page explains how to present audio stimuli from an Researcher PC with a focusrite soundcard to

More information

CONTENTS JamUp User Manual

CONTENTS JamUp User Manual JamUp User Manual CONTENTS JamUp User Manual Introduction 3 Quick Start 3 Headphone Practice Recording Live Tips General Setups 4 Amp and Effect 5 Overview Signal Path Control Panel Signal Path Order Select

More information

How to Present External Audio Stimuli from PC - Focusrite Soundcards

How to Present External Audio Stimuli from PC - Focusrite Soundcards How to Present External Audio Stimuli from PC - Focusrite Soundcards This page explains how to present audio stimuli from an Researcher PC with a focusrite soundcard to a test subject in the CMA 2 CSD

More information

Multichannel Audio Technologies: Lecture 3.A. Mixing in 5.1 Surround Sound. Setup

Multichannel Audio Technologies: Lecture 3.A. Mixing in 5.1 Surround Sound. Setup Multichannel Audio Technologies: Lecture 3.A Mixing in 5.1 Surround Sound Setup Given that most people pay scant regard to the positioning of stereo speakers in a domestic environment, it s likely that

More information

QUICKSTART OWNER S MANUAL (ENGLISH) 1 8 MANUAL DE INICIO RÁPIDO DEL USUARIO (ESPAÑOL) 9 16 GUIDE D UTILISATION SIMPLIFIÉ (FRANÇAIS) 17 24

QUICKSTART OWNER S MANUAL (ENGLISH) 1 8 MANUAL DE INICIO RÁPIDO DEL USUARIO (ESPAÑOL) 9 16 GUIDE D UTILISATION SIMPLIFIÉ (FRANÇAIS) 17 24 QUICKSTART OWNER S MANUAL (ENGLISH) 1 8 MANUAL DE INICIO RÁPIDO DEL USUARIO (ESPAÑOL) 9 16 GUIDE D UTILISATION SIMPLIFIÉ (FRANÇAIS) 17 24 KURZBEDIENUNGSANLEITUNG (DEUTSCH) 25 32 MANUALE RAPIDO DI UTILIZZO

More information

Introduction. 1. Theory of Operation

Introduction. 1. Theory of Operation Table of Contents Introduction......................................................2 1. Theory of Operation.............................................2 2. Features.......................................................3

More information

Intro to Pro Tools. Version 8.0.4

Intro to Pro Tools. Version 8.0.4 Intro to Pro Tools Version 8.0.4 Welcome to Pro Tools LE Read this guide if you are new to Pro Tools or are just starting out making your own music. Inside, you ll find quick examples of how to record,

More information

Ultimate USB & XLR Microphone for Professional Recording

Ultimate USB & XLR Microphone for Professional Recording yetipro Ultimate USB & XLR Microphone for Professional Recording 3 desktop or studio, the possibilities are endless. Congratulations on your purchase of Yeti Pro, the first microphone to combine the exceptional

More information

Nikon View DX for Macintosh

Nikon View DX for Macintosh Contents Browser Software for Nikon D1 Digital Cameras Nikon View DX for Macintosh Reference Manual Overview Setting up the Camera as a Drive Mounting the Camera Camera Drive Settings Unmounting the Camera

More information

Using an ASIO Audio Interface and Digital Audio Workstation Software with openhpsdr Revision 3 14 Jun 2015 WU2O

Using an ASIO Audio Interface and Digital Audio Workstation Software with openhpsdr Revision 3 14 Jun 2015 WU2O Using an ASIO Audio Interface and Digital Audio Workstation Software with openhpsdr Revision 3 14 Jun 2015 WU2O Introduction Many people are using relatively low cost, professional audio interfaces such

More information

TouchMix Series. Quick Start Guide. Installing the Windows Driver. Non-DAW audio playback from computer. TouchMix-30 Pro settings.

TouchMix Series. Quick Start Guide. Installing the Windows Driver. Non-DAW audio playback from computer. TouchMix-30 Pro settings. TouchMix Series Quick Start Guide Setting up TouchMix-30 Pro with a computer: Windows driver installation, ios Core Audio configuration, itunes playback, and DAW setup This quick start guide is to help

More information

Version 3.6 User Guide

Version 3.6 User Guide Version 3.6 User Guide Getting Started With Your Hardware GX UX1 UX2 KB37 DI UX8 POD X3 POD X3 Live PODxt PODxt Live PODxt Pro Guitar Port Stand-Alone Application GearBox Basics GearBox with POD X3 GearBox

More information

Mana Recording Studios

Mana Recording Studios Mana Recording Studios Mixing Requirements and Guidelines This document is list of requirements and guidelines for projects that are being sent to us for mixing. The goal of this document is to help us

More information

User Guide FFFA

User Guide FFFA User Guide FFFA001253 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Introduction...3 Features.................................................................... 4 Box Contents...4 System Requirements....4

More information

There are three modes of operation for JoeCoControl selectable from the drop down menu in the blue top bar of the Mic/Line input controls window.

There are three modes of operation for JoeCoControl selectable from the drop down menu in the blue top bar of the Mic/Line input controls window. JoeCoControl Overview JoeCo control is a powerful application for Mac or PC that allows full control of your JoeCo BlueBox Workstation Recorder product. To use JoeCo control, connect the USB2 cable supplied

More information

M-16DX 16-Channel Digital Mixer

M-16DX 16-Channel Digital Mixer M-6DX 6-Channel Digital Mixer Workshop Live Mixing with the M-6DX 007 Roland Corporation U.S. All rights reserved. No part of this publication may be reproduced in any form without the written permission

More information

Dubbing Audio in the Adv. Dub Room

Dubbing Audio in the Adv. Dub Room Dubbing Audio in the Adv. Dub Room The MC1319 Dubroom is equipped with an Audio Rack for dubbing audio from common audio formats to digital files. This dubbing guide is a step by step manual for using the

More information

M-16DX 16-Channel Digital Mixer

M-16DX 16-Channel Digital Mixer M-6DX 6-Channel Digital Mixer Workshop Using the M-6DX with SONAR LE 007 Roland Corporation U.S. All rights reserved. No part of this publication may be reproduced in any form without the written permission

More information

Universal audio/midi interface USER MANUAL

Universal audio/midi interface USER MANUAL Universal audio/midi interface USER MANUAL Contents Table of Contents Contents 2 English 3 Safety information 3 irig Pro DUO 3 Register your irig Pro DUO 3 irig Pro DUO overview 4 Installation and setup

More information

SOFTWARE: HARDWARE: K a t i e W a r d r o b e

SOFTWARE: HARDWARE: K a t i e W a r d r o b e REALLY EASY RECORDING & EDITING This session will look at the basics of recording and editing student performances using inexpensive equipment and free software. The techniques covered are perfect for

More information

User Guide. Version 1.0 POWER

User Guide.  Version 1.0 POWER User Guide POWER Version 1.0 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Introduction...3 Product Compatibility...3 Features.................................................................... 4

More information

Miktek, LLC Nashville, TN USA tel: fax:

Miktek, LLC Nashville, TN USA tel: fax: Miktek, LLC Nashville, TN USA tel: 615.250.2434 fax: 615.346.9298 2017 All Rights Reserved, Miktek, LLC. Printed May 2017 v1 www. miktekaudio.com PRINTED IN CHINA Table of Contents Introduction.......................................................

More information

Print then Cut Calibration

Print then Cut Calibration Calibration The feature of Cricut Design Space for PC and Mac allows you to print your images from your home printer and then cut them out with high precision on your Cricut machine. Print then Cut calibration

More information

Owner s Manual COMPLETE RECORDING SOLUTION

Owner s Manual COMPLETE RECORDING SOLUTION Owner s Manual COMPLETE RECORDING SOLUTION Warranty/Technical Support/Service WARRANTY 1. Please register your product online at lexiconpro.com. Proof-of-purchase is considered to be the responsibility

More information

eti Ultimate USB microphone for professional recording

eti Ultimate USB microphone for professional recording eti Ultimate USB microphone for professional recording 3 Congratulations on your purchase of The Yeti, the most advanced and versatile multi-pattern USB microphone roaming the wild today. The Yeti is

More information

Contents. Introduction to Saffire PRO 10 i/o Getting connected and setting up the hardware/software Front Panel Features...

Contents. Introduction to Saffire PRO 10 i/o Getting connected and setting up the hardware/software Front Panel Features... Contents Introduction to... 2 Getting connected and setting up the hardware/software... 3 Front Panel Features... 4 Rear Panel Features... 5 SaffireControl PRO software Features... 6 Recording analogue

More information

HOW TO SETUP PROTOOLS SOFTWARE

HOW TO SETUP PROTOOLS SOFTWARE HOW TO SETUP PROTOOLS SOFTWARE The iz Dual ProTools HD Interface can work with ProTools HD systems running on a Windows PC or Mac OS X computer. Using the iz Dual ProTools HD Interface with ProTools software

More information

MUSC 1331 Lab 3 (Northwest) Using Software Instruments Creating Markers Creating an Audio CD of Multiple Sources

MUSC 1331 Lab 3 (Northwest) Using Software Instruments Creating Markers Creating an Audio CD of Multiple Sources MUSC 1331 Lab 3 (Northwest) Using Software Instruments Creating Markers Creating an Audio CD of Multiple Sources Objectives: 1. Learn to use Markers to identify sections of a sequence/song/recording. 2.

More information

Recording guidebook This provides information and handy tips on recording vocals and live instruments at home.

Recording guidebook This provides information and handy tips on recording vocals and live instruments at home. Welcome to The Hit Kit s QuickStart instructions! Read on and you ll be set up and making your first steps in the world of music making in no time at all! Remember, you can find complete instructions to

More information

Version 2 - Advanced User Guide

Version 2 - Advanced User Guide Version 2 - Advanced User Guide Getting Started With Your Hardware GX UX1 UX2 KB37 UX8 DI Guitar Port POD X3 Family PODXT Family ilok POD Farm 2 Basics POD Farm 2 Plug-In Elements Plug-Ins Standalone Operation

More information

The House of Faith United Methodist Church of Yucaipa Sound Technician Training

The House of Faith United Methodist Church of Yucaipa Sound Technician Training The House of Faith United Methodist Church of Yucaipa Sound Technician Training Sound Board, Screen, and Computer Setup 1. Turn on the Master Power switch on the power strip under the right side of the

More information

How To Mac. Setup your Macintosh computer: Go to APPLICATIONS > UTILITIES > AUDIO MIDI SETUP Set the AUDIO DEVICE as shown to use the mlan NETWORK

How To Mac. Setup your Macintosh computer: Go to APPLICATIONS > UTILITIES > AUDIO MIDI SETUP Set the AUDIO DEVICE as shown to use the mlan NETWORK How To Mac Setting up a Network with the Yamaha 01X, Motif XS and Mac computer mlan TOOLS for Macintosh version 1.2.0 (November 2008) Motif XS w/mlan16e2 - Operating System version 1.55.xx, IEEE1394 Firmware

More information

Henley College Radio Studio. User Guide

Henley College Radio Studio. User Guide Henley College Radio Studio User Guide Starting up If the computer isn t on and ready to record, you will need to follow these steps: Turn the computer on under the desk It should automatically login and

More information

Audacity 5EBI Manual

Audacity 5EBI Manual Audacity 5EBI Manual (February 2018 How to use this manual? This manual is designed to be used following a hands-on practice procedure. However, you must read it at least once through in its entirety before

More information

VERSION 3.5 RELEASE NOTES

VERSION 3.5 RELEASE NOTES VERSION 3.5 RELEASE NOTES Mac OS X 10.4, Windows XP Updated Nov. 19, 2007 TABLE OF CONTENTS System Requirements... 2 Supported Line 6 Hardware...2 Windows System Requirements...2 Mac System Requirements...2

More information

LINE 6 GEARBOX 3.1 RECORDING SETUP GUIDE

LINE 6 GEARBOX 3.1 RECORDING SETUP GUIDE LINE 6 GEARBOX 3.1 RECORDING SETUP GUIDE Table of Contents LINE 6 GEARBOX 3.1 RECORDING SETUP GUIDE Getting Started...4 Updating & registering with Line 6 Monkey...4 About this guide...4 GearBox settings

More information

Hardware options for Pro Tools LE and M-Powered systems

Hardware options for Pro Tools LE and M-Powered systems Hardware options for Pro Tools LE and M-Powered systems Pro Tools LE software requires you to connect a suitable Digidesign hardware interface to your computer before it will run. Digidesign hardware for

More information

Recording Overview. We will cover the following topics over the course of the semester:

Recording Overview. We will cover the following topics over the course of the semester: Recording Overview We will cover the following topics over the course of the semester: Basic (simultaneous) tracking: recording multiple tracks at the same time. This is commonly the procedure used when

More information

LINE 6 GEARBOX 3.0 RECORDING SETUP GUIDE

LINE 6 GEARBOX 3.0 RECORDING SETUP GUIDE LINE 6 GEARBOX 3.0 RECORDING SETUP GUIDE Table of Contents LINE 6 GEARBOX 3.0 RECORDING SETUP GUIDE Getting Started...1 Updating & registering with Line 6 Monkey...1 About this guide...1 GearBox settings

More information

IGNITE BASICS V1.1 19th March 2013

IGNITE BASICS V1.1 19th March 2013 IGNITE BASICS V1.1 19th March 2013 Ignite Basics Ignite Basics Guide Ignite Basics Guide... 1 Using Ignite for the First Time... 2 Download and Install Ignite... 2 Connect Your M- Audio Keyboard... 2 Open

More information

creation stations AUDIO RECORDING WITH AUDACITY 120 West 14th Street

creation stations AUDIO RECORDING WITH AUDACITY 120 West 14th Street creation stations AUDIO RECORDING WITH AUDACITY 120 West 14th Street www.nvcl.ca techconnect@cnv.org PART I: LAYOUT & NAVIGATION Audacity is a basic digital audio workstation (DAW) app that you can use

More information

User Guide. Version 1.0.

User Guide. Version 1.0. User Guide Version 1.0 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Introduction...3 Features.................................................................... 4 Box Contents...5 System Requirements....5

More information

Hardware Reference written by Alexander Stamm, edited by Patryk Korman Document Version: 1.0 (07/2009) Product Version: 4.

Hardware Reference written by Alexander Stamm, edited by Patryk Korman Document Version: 1.0 (07/2009) Product Version: 4. HARDWARE REFERENCE The information in this document is subject to change without notice and does not represent a commitment on the part of Native Instruments GmbH. The software described by this document

More information

Using Your StudioLive Mixer as an Audio Interface with Universal Control

Using Your StudioLive Mixer as an Audio Interface with Universal Control Using Your StudioLive Mixer as an Audio Interface with Universal Control Reference Manual Universal Control www.presonus.com English Table of Contents 1 Overview 1 1.1 Introduction 1 1.2 About This Manual

More information

Before You Start. Program Configuration. Power On

Before You Start. Program Configuration. Power On StompBox is a program that turns your Pocket PC into a personal practice amp and effects unit, ideal for acoustic guitar players seeking a greater variety of sound. StompBox allows you to chain up to 9

More information

Version 2 - Basic User Guide

Version 2 - Basic User Guide Español Deutsch Français Nederlands 日本語 Version 2 - Basic User Guide GX POD Studio Interfaces GX UX1 UX2 KB37 ilok POD Farm 2 Basics POD Farm 2 Elements Plug-In Plug-Ins Standalone Operation Online Resources

More information

User Guide FFFA

User Guide FFFA User Guide FFFA001255 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Introduction...3 Features.................................................................... 4 Box Contents...4 System Requirements....4

More information

Best case scenario for recording with the 8M MOTU sound card and Audacity

Best case scenario for recording with the 8M MOTU sound card and Audacity Best case scenario for recording with the 8M MOTU sound card and Audacity Preparations select DELL from the EXTRON USB device (located on the desk) making sure it is lit up, and not MAC. select DELL from

More information

creation stations AUDIO RECORDING WITH AUDACITY 120 West 14th Street

creation stations AUDIO RECORDING WITH AUDACITY 120 West 14th Street creation stations AUDIO RECORDING WITH AUDACITY 120 West 14th Street www.nvcl.ca techconnect@cnv.org PART I: LAYOUT & NAVIGATION Audacity is a basic digital audio workstation (DAW) app that you can use

More information

GIS Module GMS 7.0 TUTORIALS. 1 Introduction. 1.1 Contents

GIS Module GMS 7.0 TUTORIALS. 1 Introduction. 1.1 Contents GMS 7.0 TUTORIALS 1 Introduction The GIS module can be used to display data from a GIS database directly in GMS without having to convert that data to GMS data types. Native GMS data such as grids and

More information

User Guide ios. MWM - edjing, 54/56 avenue du Général Leclerc Boulogne-Billancourt - FRANCE

User Guide ios. MWM - edjing, 54/56 avenue du Général Leclerc Boulogne-Billancourt - FRANCE User Guide MWM - edjing, 54/56 avenue du Général Leclerc 92100 Boulogne-Billancourt - FRANCE Table of contents First Steps 3 Accessing your music library 4 Loading a track 8 Creating your sets 10 Managing

More information

User Manual USB Condenser Microphone

User Manual USB Condenser Microphone User Manual USB Condenser Microphone MICF-3001 Overview 1 Setting Up 1 Using the microphone with Windows 7/8/10 PC 3 Using a headphone with CF3001 4 Monitor your voice level (Computer system feature) 5

More information

Virtual Mix Room. User Guide

Virtual Mix Room. User Guide Virtual Mix Room User Guide TABLE OF CONTENTS Chapter 1 Introduction... 3 1.1 Welcome... 3 1.2 Product Overview... 3 1.3 Components... 4 Chapter 2 Quick Start Guide... 5 Chapter 3 Interface and Controls...

More information

v. 8.0 GMS 8.0 Tutorial GIS Module Shapefile import, display, and conversion Prerequisite Tutorials None Time minutes

v. 8.0 GMS 8.0 Tutorial GIS Module Shapefile import, display, and conversion Prerequisite Tutorials None Time minutes v. 8.0 GMS 8.0 Tutorial Shapefile import, display, and conversion Objectives Learn how to import and display shapefiles with and without ArcObjects. Convert the shapefiles to GMS feature objects. Prerequisite

More information

WPE 48N USER MANUAL Version1.1

WPE 48N USER MANUAL Version1.1 Version1.1 Security instructions 1. Read this manual carefully. 2. Follow all instructions and warnings. 3. Only use accessories specified by WORK PRO. 4. Follow the safety instructions of your country.

More information

Virtual Microphone System Quick Start

Virtual Microphone System Quick Start Virtual Microphone System Quick Start This quick start guide will help you get acquainted with your VMS so you can start making the best sounding music with it, fast. Making Connections 1. Connect your

More information

Getting Started Guide

Getting Started Guide SOLIDWORKS Getting Started Guide SOLIDWORKS Electrical FIRST Robotics Edition Alexander Ouellet 1/2/2015 Table of Contents INTRODUCTION... 1 What is SOLIDWORKS Electrical?... Error! Bookmark not defined.

More information

Portable Audio interface for ios, USB USER MANUAL

Portable Audio interface for ios, USB USER MANUAL Portable Audio interface for ios, USB USER MANUAL Contents Table of Contents Contents 2 English 3 irig Pre HD 3 Register your irig Pre HD 3 Installation and setup 4 ios devices 4 MAC/PC 6 irig Pre HD LEDs

More information

LAUNCHPAD. Getting Started Guide

LAUNCHPAD. Getting Started Guide LAUNCHPAD Getting Started Guide Overview Launchpad Thank you for buying Launchpad, the iconic grid instrument for Ableton Live. You re now part of the evolution in the creation of electronic music! The

More information

Quantum-series Ultra-low latency Thunderbolt Audio Interfaces and Studio Command Centers

Quantum-series Ultra-low latency Thunderbolt Audio Interfaces and Studio Command Centers Ultra-low latency Thunderbolt Audio Interfaces and Studio Command Centers www.presonus.com English Table of Contents 1 Overview 1 1.1 Introduction 1 1.2 Interface Hardware Features 1 1.3 UC Surface Features

More information

How big is your room and what are the walls made out of?

How big is your room and what are the walls made out of? Objective: By the end of this lab you will be able to hide, display and call up any reverb and to deduce how to load presets and manipulate the various components within a reverb. To be able do duplicate

More information

This page intentionally left blank 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%

This page intentionally left blank 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Reference Manual This page intentionally left blank 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Table Of Contents Introduction...5 Welcome!...5 About the MultiMix 8 FireWire...6 All-In-One Mixer and Multichannel

More information

Mediasite Desktop Recorder: Recording a Lecture 2017

Mediasite Desktop Recorder: Recording a Lecture 2017 Mediasite Desktop Recorder: Recording a Lecture 2017 This lesson will show you how to record a presentation using the Mediasite Desktop Recorder. In browser go to - https://http://mediasite.umaryland.edu/mediasite/mymediasite

More information

Guitar Reamping Guide

Guitar Reamping Guide Guitar Reamping Guide Contents: Situations when reamping is helpful Why do I need a separate box for reamping? I have been ok without so far Here is what I use in my studio Basic Steps to Reamping Guitar

More information

User Guide. Version 1.0.

User Guide. Version 1.0. User Guide Version 1.0 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Introduction...3 Features.................................................................... 4 Box Contents...5 System Requirements....5

More information

User Guide. Version 1.2.

User Guide. Version 1.2. User Guide Version 1.2 www.focusrite.com TABLE OF CONTENTS OVERVIEW.... 3 Features.................................................................... 4 Box Contents...5 System Requirements....5 Getting

More information

HTC VIVE Installation Guide

HTC VIVE Installation Guide HTC VIVE Installation Guide Thank you for renting from Hartford Technology Rental. Get ready for an amazing experience. To help you setup the VIVE, we highly recommend you follow the steps below. Please

More information

Owner s Manual COMPLETE RECORDING SOLUTION

Owner s Manual COMPLETE RECORDING SOLUTION Owner s Manual COMPLETE RECORDING SOLUTION Warranty/Technical Support/Service WARRANTY 1. Please register your product online at lexiconpro.com. Proof-of-purchase is considered to be the responsibility

More information

Sound Skulptor MC624 User manual

Sound Skulptor MC624 User manual Sound Skulptor MC624 User manual 1. Overview The MC624 lets you select one out of six stereo line level audio sources, adjust the level and route it to one out of four stereo amplified monitor pairs. The

More information