Assembly Manual - Flamenco Guitar Kit

Size: px
Start display at page:

Download "Assembly Manual - Flamenco Guitar Kit"

Transcription

1 Assembly Manual - Flamenco Guitar Kit

2 Index Contents (pg. 3) Soundboard assembly (pg. 4) Neck to top assembly (pg. 5) Preparation of the sides (pg. 6) Preparation of the back (pg. 7) Body assembly (pg. 8) Binding (pg. 9) Fingerboard gluing (pg. 11) Fretting (pg. 11) Sanding (pg. 12) Bridge gluing (pg. 12) Tuning machine fitting and stringing (pg. 13) 2

3 Contents: 1 650mm Cedar neck with Ebony strip & Indian Rosewood headplate 1 European Spruce top with soundhole rosette 1 Set of pre-bent solid Cypress sides 1 Set of pre-bent laminated Sapele linings 1 Cedar end-block 1 Cypress joined back with black backstrip 1 Set of three Cedar back braces 4 Pre-bent Indian Rosewood / white veneer bindings 2 Black and white veneer purflings 2 White veneer purflings 1 Slotted Ebony fingerboard 2 Strips of 2.5mm fretwire mm bone nut 1 Bone saddle 1 Indian Rosewood bridge with tie-block inlay 1 Set of soundboard transverse braces 1 Indian Rosewood heel cap 1 Indian Rosewood white laminated tailblock strip 1 Spruce back reinforcing strip 1 Tuning machine set 1 Set of Savarez strings 1 Assembly manual 3

4 Soundboard assembly: Step 1.- Sand the top until the desired thickness (between 2.4 and 2.6mm is recommended) is achieved. Glue the entire bracing according to the enclosed diagrams, eliminating all excess glue. Sand all the inside bracing until a rounded and even finish is achieved, thus eliminating all the sharp edges from each of the previously glued pieces; see Figure 2. fig.1 fig.2 4

5 Neck to Top assembly: Step 1.- Cut the design of the head and adjust the top rebate in the neck according to the final thickness of the top. Assemble the top so that it lies perfectly flush over the neck rebate and align using the two grooves located on the underside and surface of the top. 5

6 Preparation of the sides: Step 1.- Join the sides at the end-block, using only glue. Once the glue has dried, set the end-block flush onto the sides. Glue the Sapele linings on the inside outline of the sides, from the end-block to the area where the sides join the neck foot, leaving space for the assembly of the neck. Start by gluing from the centre of the sides (waist), and set the four pieces flush on both the top and bottom of the sides. 6

7 Preparation of the back: Step 1.- Sand the back until the desired thickness is achieved (2.4 mm is recommended). Next, glue the three inside reinforcements (braces) according to the diagram. Glue on a curved surface so that the back matches the curvature of the braces. Once they have dried, glue the centre reinforcement (joint-cover), cutting and adjusting the four pieces from the end of the neck heel to the end-block. Sand all the previously glued pieces, thus eliminating all sharp edges, as seen in Figure 2. fig.1 fig.2 7

8 Body Assembly: Step 1.- Mark the position of the 2 top transverse braces to know where to make the rebate that will fix them to the lining. Dry join and clamp the top to the sides inserting the sides on the neck and ensuring that it is perfectly placed and square to the sides. After that you can apply glue to the entire outline of the sides and clamp. Mark the position of back braces 1, 2 and 3 to know where to make the rebate that will fix them to the lining. Dry join and clamp the back to the sides ensuring that it is perfectly placed and square to the sides. After that you can apply glue to the entire outline of the sides and clamp. 8

9 Binding: Step 1.- Make a slot on the upper outline (Top/Side) of the dimensions of the binding that will be used for the top, according to the diagram. Make a slot on the lower outline (Back/Side) of the dimensions of the binding that will be used for the back, according to the diagram. 9

10 Step 3.- Make a slot on the outer part of the union of both sides, where the end-block inlay will be set afterwards. Step 4.- Glue the bindings of the top and the back, moving from the neck to the end-block so that the union between both is perfectly centered in the middle of the slot at the end-block. Once the bindings are dry, inlay the end-block strip by mitring the white bindings, according to the enclosed diagram. Eliminate back wood excess over the heel and prepare the area for the rosewood heel cap. Glue the heel cap on the heel. Once it is dry work it to the shape of the heel. 10

11 Fingerboard gluing: Apply glue to the glueing side of the fingerboard and position it over the neck, using the soundhole as a guide. Fret no. 12 should coincide right where the sides meet the neck. Apply pressure for 24 hours. Fretting: Cut lengths of fretwire with a 5 mm overhang at each side. Apply glue on the fingerboard slots and fit the frets into each one. Once the glue is dry, cut the fret excess at each side of the fingerboard and file and sand the edges of the fretwire flush with the fingerboard. Next, file and sand the ends of the fret crowns to achieve 45º bevel. 11

12 Sanding: Thoroughly sand the entire guitar with fine grain sandpaper, smoothing all the differences on the binding and completely eliminating all excess glue.. Bridge gluing: Step 1.- Adjust the position for the nut between the fingerboard and the headstock. Place the bridge so that it is perfectly aligned in the centre of the guitar at a distance between the nut and the saddle of 650mm. Exactly at the half, 325mm, it should coincide with the 12th fret. Glue it to the top, applying pressure for 48 hours. 12

13 Tuning machine fitting and stringing: Step1.- Position the tuning machine over the drill holes of the head and fasten it using the screws provided. Tie the strings starting with the bass strings from the bridge toward the tuning machine. Tighten the strings and adjust the action with both the nut and saddle to the desired height; 3mm at the position of fret no. 12 is recommended. Note: The assembly should be carried out by an expert, because if the steps are not followed correctly, the desired result might not be attained. In these instructions, a brief description of the process of assembling a classical guitar is made, and the use of additional teaching materials (books, videos, plans) is highly recommended for further information. ATTENTION! No adhesives or tools for assembly are included. Remember that the adhesives and tools you select must be appropriate for use with the different materials. If you have any doubt, consult your local specialists. The manufacturer takes no responsibility for improper use of the pieces provided, nor for the result after assembling them. 13

14 14

15 Planimetry 15

Build Table of Contents. 1. Introduction

Build Table of Contents. 1. Introduction Build Table of Contents 1. Introduction... 1-2 2. A Brief Review of Assembly Systems... 2-2 2.1. Free Assembly Methods... 2-3 2.2. Constrained Assembly Methods... 2-4 3. Our Approach to Building... 3-2

More information

BUILDING A SELMER MACCAFERRI GUITAR

BUILDING A SELMER MACCAFERRI GUITAR BUILDING A SELMER MACCAFERRI GUITAR A step-by-step guide to building a laminated body Selmer-Maccaferri guitar Michael Collins The Heel The heel should now be prepared to be glued to the neck shaft. Using

More information

GUITAR ANATOMY GLOSSARY

GUITAR ANATOMY GLOSSARY GUITAR ANATOMY GLOSSARY abalone: an iridescent lining found in the inner shell of the abalone mollusk that is often used alongside mother of pearl; commonly used as an inlay material. action: the distance

More information

Tools and materials, which are well needed for assembling the Tenayo Ukulele KITs Rasp, file and sandpapers with different granulations for the sandin

Tools and materials, which are well needed for assembling the Tenayo Ukulele KITs Rasp, file and sandpapers with different granulations for the sandin Tenayo TK-UK-1, 2, 3 und 4 Ukulele: Facts, Manual & Introduction Text und photos by Michael Koch The Ukulele was invented and brought to Hawaii until the end of the 19. Century by a Portuguese named João

More information

Dreadnought Acoustic Guitar Kit #5295 Assembly Instructions stewmac.com

Dreadnought Acoustic Guitar Kit #5295 Assembly Instructions stewmac.com Dreadnought Acoustic Guitar Kit #5295 Assembly Instructions Table of contents Getting started Welcome to guitar building!... 2 Recommended tools and supplies... 2 Kit parts list... 3 Side Assembly Assembling

More information

Triple-O Acoustic Guitar Kit #5297 Assembly Instructions

Triple-O Acoustic Guitar Kit #5297 Assembly Instructions Triple-O Acoustic Guitar Kit #5297 Assembly Instructions www. Table of contents Getting started Welcome to guitar building!... 2 Recommended tools and supplies... 2 Kit parts list... 3 Side Assembly Assembling

More information

Catalog - January 2016

Catalog - January 2016 Catalog - January 2016 1 Guitarras Manuel Rodríguez Rich in sound, rich in history, rich in beauty... since 1905. Tradition, exotic wood, sawdust and varnish smell go along with the large family that makes

More information

U-bass Kit Assembly Instructions

U-bass Kit Assembly Instructions U-bass Kit Assembly Instructions Compiled by playubass.com This guide is built from the instructions found here: http://kalabrand.com/ubass-kit/index.html Tools Needed 5/8 (16 mm) Wrench 7/16 (~11 mm)

More information

Soprano Ukulele Kit #5347 Assembly Instructions

Soprano Ukulele Kit #5347 Assembly Instructions Soprano Ukulele Kit #5347 Assembly Instructions Soprano Ukulele Kit Assembly Instructions Table of contents Welcome to ukulele building! Getting started.................................... 1 Kit parts

More information

Join Neck and Body Wednesday, January 16, :08 PM

Join Neck and Body Wednesday, January 16, :08 PM ASL Breakdown Page 1 Join Neck and Body Wednesday, January 16, 2013 10:08 PM 1. 2. 3. 4. Charles did the following steps to speed things up: Lightly sanded the top of the lower bout with an orbital sander.

More information

Restoration of Unknown Maker Folk Guitar

Restoration of Unknown Maker Folk Guitar Restoration of Unknown Maker Folk Guitar Performed by Ron Cook 1998 Purchased by Ron Cook at Three Amigos Guitar Show, San José, California Currently owned by Anna Liikala, Santa Cruz, California Background

More information

StewMac. Sheet #i-5371 Updated 11/18 PREMIUM SOLID-WOOD UKULELE KIT. Assembly Instructions

StewMac. Sheet #i-5371 Updated 11/18 PREMIUM SOLID-WOOD UKULELE KIT. Assembly Instructions StewMac Sheet #i-5371 Updated 11/18 PREMIUM SOLID-WOOD UKULELE KIT Assembly Instructions Table of contents Tools and supplies... 2 Parts list... 3 Installing the rosette... 4 Brace the top and back....

More information

DAKOTA OCTAVE MANDOLIN KIT and MANDOCELLO KIT

DAKOTA OCTAVE MANDOLIN KIT and MANDOCELLO KIT DAKOTA OCTAVE MANDOLIN KIT and MANDOCELLO KIT MUSICMAKER S KITS, INC PO Box 2117 Stillwater, MN 55082 651-439-9120 harpkit.com WOOD PARTS: DAKOTA OCTAVE MANDOLIN KIT A - Neck B - Fretboard C - Heel Block

More information

Assembly instructions for Classic Cantabile DIY Ukulele

Assembly instructions for Classic Cantabile DIY Ukulele Assembly instructions for Classic Cantabile DIY Ukulele ArtNr.: 00036326 Sopranukulele / 00036327 Konzertukulele Musikhaus Kirstein GmbH Bernbeurener Strasse 11 D-86956 Schongau / Germany Tel.: 0049-8861-909494-0

More information

Read Me First! PICKUP INSTALLATION MATRIX INFINITY VT MATRIX INFINITY MIC BLEND INSTALLATION GUIDE. *Minimum 20⁰ string break angle

Read Me First! PICKUP INSTALLATION MATRIX INFINITY VT MATRIX INFINITY MIC BLEND INSTALLATION GUIDE. *Minimum 20⁰ string break angle MATRIX INFINITY VT MATRIX INFINITY MIC BLEND INSTALLATION GUIDE Read Me First! We recommend having this system installed by an experienced repair technician *Minimum 20⁰ string break angle PICKUP INSTALLATION

More information

3Insert the second rod no. 4

3Insert the second rod no. 4 Yamato: Step-by-step 37 The stern block and searchlight control towers a b c d e f Recommended tools and materials Wood glue Sandpaper (no. 800 grain) Metal file Putty Craft knife For metal: Super Glue

More information

Read Me First! PICKUP INSTALLATION MATRIX INFINITY VT MATRIX INFINITY MIC BLEND INSTALLATION GUIDE. *Minimum 20⁰ string break angle

Read Me First! PICKUP INSTALLATION MATRIX INFINITY VT MATRIX INFINITY MIC BLEND INSTALLATION GUIDE. *Minimum 20⁰ string break angle MATRIX INFINITY VT MATRIX INFINITY MIC BLEND INSTALLATION GUIDE Read Me First! We recommend having this system installed by an experienced repair technician *Minimum 20⁰ string break angle PICKUP INSTALLATION

More information

Build the Spitfire: Step-By-step. Pack 3 Stages 21-30

Build the Spitfire: Step-By-step. Pack 3 Stages 21-30 Pack Stages 2-0 Contents Stage Page Number 2 72-74 22 75-78 2 79-8 24 82-84 25 85-88 26 89-9 27 92-94 28 95-97 29 98-00 0 0-05 Editorial and design by Continuo Creative, 9-4 North Road, London N7 9DP All

More information

Electric Ukulele. Plans

Electric Ukulele. Plans Electric Ukulele Plans Build a tenor electric ukulele! Daniel Hulbert 2014 CircuitsAndStrings.wordpress.com 2 Parts and Supplies: Two 3/4 by 5 by 12 inch (19 mm x 127 mm x 305 mm) pieces of wood for the

More information

Retail prices 2019 International reference price list

Retail prices 2019 International reference price list Retail prices 2019 International reference price list Retail prices 2019 - International reference Recommended retail prices in Euro ( ) incl. 19% German VAT - international reference prices valid from

More information

BUILDING MARTIN-STYLE ACOUSTIC GUITAR KITS 41

BUILDING MARTIN-STYLE ACOUSTIC GUITAR KITS 41 Braces To Be Tucked Into Lining The braces in the photo at right with circles at the ends are those that will be notched into the lining of the guitar. In this procedure, the end of the brace is trimmed

More information

StewMac. Sheet #i-5351 Updated 11/17 UKULELE KIT. Assembly Instructions

StewMac. Sheet #i-5351 Updated 11/17 UKULELE KIT. Assembly Instructions StewMac Sheet #i-5351 Updated 11/17 UKULELE KIT Assembly Instructions Table of contents Tools and supplies... 2 Parts list... 3 Brace the top and back.... 4 Make the body mold... 6 Assemble the body...

More information

Contents. Build the Spitfire: Step-By-step

Contents. Build the Spitfire: Step-By-step Pack 2 Stages -20 Contents Stage Page Number 8-0 2 - - 7 8-50 5 5-5 6 5-57 7 58-60 8 6-6 9 6-67 20 68-7 Editorial and design by Continuo Creative, 9- North Road, London N7 9DP All rights reserved 20 De

More information

Grade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website

Grade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure

More information

Owner s Manual. Bass-Guitar Kit J-Style

Owner s Manual. Bass-Guitar Kit J-Style Owner s Manual Bass-Guitar Kit J-Style Contents Introduction... 3 Body finish... 4 Neck finish... 4 Assembling of tuners... 5 Neck... 6 Wiring... 6 Bridge assembly... 8 Strap buttons... 8 Setting up...

More information

K-1 DELUXE (SUPER SOPRANO)

K-1 DELUXE (SUPER SOPRANO) K-1 NATURAL FINISH (SOPRANO) Also available in: Super Soprano, Concert, Super Concert, Tenor, Tenor 6, Tenor 8, Super Tenor, Baritone, GL6 Koa Body, Rosewood Fret Board and Bridge, Chrome Open Geared Tuner,

More information

How to Build a Fretless, Acoustic Cigar Box Guitar

How to Build a Fretless, Acoustic Cigar Box Guitar How to Build a Fretless, Acoustic Cigar Box Guitar Introduction Welcome to the fun and world of building Cigar Box Guitars. It is unlikely that you will build only one - it is addictive. Regardless of

More information

Prices & Model Specifications April 2009

Prices & Model Specifications April 2009 Bourgeois guitars are handcrafted in Maine from the finest available tonewoods, which we select, match and voice for each individual instrument. Except as noted, all models include the following features:

More information

Dakota Concert Ukulele

Dakota Concert Ukulele Dakota Concert Ukulele Updated February 2019 Musicmakers 14525 61st ST CT N Stillwater, MN 55082 WOOD PARTS: A - Neck B - Fingerboard C - Heel Block D - Tail Block E - Clamping Block F - 2 Short Ribs G

More information

MUSICAL INSTRUMENT MAKING CLASSICAL OR STEEL STRUNG ACOUSTIC GUITARS

MUSICAL INSTRUMENT MAKING CLASSICAL OR STEEL STRUNG ACOUSTIC GUITARS SHORT COURSE DETAILS SMI07740 Tutor: Dates: MUSICAL INSTRUMENT MAKING CLASSICAL OR STEEL STRUNG ACOUSTIC GUITARS PETER BARTON 9 DAYS TUESDAY 27 MARCH THURSDAY 5 APRIL West Dean College has run musical

More information

Solo AD Style DIY Acoustic Guitar Kit

Solo AD Style DIY Acoustic Guitar Kit Solo AD Style DIY Acoustic Guitar Kit Assembly Manual ADK-1 V 2.0 Copyright 2017 Solo Music Gear. All rights reserved Show Off Your Custom Built Guitar! When you have your guitar finished, please take

More information

Build the Spitfire: Step-By-step. Pack 4 Stages 31-40

Build the Spitfire: Step-By-step. Pack 4 Stages 31-40 Pack 4 Stages 31-40 1 Contents Stage Page Number 31 106-108 32 109-111 33 112-115 34 116-118 35 119-122 36 123-125 37 126-128 38 129-132 39 133-136 40 137-139 Editorial and design by Continuo Creative,

More information

Making Simple Bookbinding Equipment

Making Simple Bookbinding Equipment Tony Firman 20 1 2 19 Notes Tony Firman Tony Firman Bookbinding 18 3 : 2012 Tony Firman Bookbinding P.O. Box 507 Haslet, TX 76052 www.tonyfirmanbookbinding.com 4. When all the tapes have been pinned in

More information

Resonator Guitar Kit. Assembly Instructions.

Resonator Guitar Kit. Assembly Instructions. Resonator Guitar Kit Assembly Instructions www.stewmac.com Table of Contents Getting started................................................ 1 Installing the truss rod.........................................

More information

COFFEE TABLE WITH RECESSED TRAY

COFFEE TABLE WITH RECESSED TRAY COFFEE TABLE WITH RECESSED TRAY Why not treat your guests to a tray laid with delicacies and then remove it from sight in your new coffee table. There's no easier way to show that you are a thoughtful

More information

GTS Music diy-guitar.com

GTS Music diy-guitar.com GTS Music diy-guitar.com IB Jem Style Kit GTS Music 313 Strachan St. Port Hope, Ontario L1A 0C2 Canada sales@diyguitarkits.net Please read these instructions carefully before beginning in order to have

More information

Robert Bosch GmbH. Minimalist washstand

Robert Bosch GmbH. Minimalist washstand Minimalist washstand Neat and tidy Minimalist washstand Minimalist design in the bathroom is in fashion. And rightly so, as this washstand proves: because less is more! 1 Introduction Here s an idea to

More information

Documentation. Written and researched by Florian Vorreiter P ROJECT:

Documentation. Written and researched by Florian Vorreiter P ROJECT: Documentation P ROJECT: R ESEARCH ON HISTORICAL GUITARS - STUDYING AND DOCUMENTING ARTISTIC DETAILS AND CONSTRUCTION Written and researched by Florian Vorreiter Acknowledgements When I started this project

More information

Owner s Manual e-guitar Kit sg-style Harley Benton E-Guitar Kit SG-Style

Owner s Manual e-guitar Kit sg-style Harley Benton E-Guitar Kit SG-Style Owner s Manual E-Guitar Kit SG-Style Contents Introduction... 3 Body finish... 4 Neck finish... 4 Assembling of tuners... 5 Neck... 6 Wiring... 7 Bridge assembly... 10 Strap buttons... 11 Setting up...

More information

BUILD THE. Soleil Royal. Pack 1. The flagship of King Louis XIV.

BUILD THE. Soleil Royal. Pack 1. The flagship of King Louis XIV. BUILD THE Soleil Royal The flagship of King Louis XIV www.model-space.com Pack 1 Stage 1 Assembly Guide Hull frame, false keel and first deck half A 4 2 5 1 6 7 1A Smooth the surfaces of all the pieces

More information

Before continuing I cleaned up the edge to get rid of the old glue and broken remnants ready to accept the top.

Before continuing I cleaned up the edge to get rid of the old glue and broken remnants ready to accept the top. Framus Guitar Restoration 2nd March 2015 This early 1970s Framus has had a bit of a hard life. Whilst working abroad around 1980-ish the present owner s brother accepted it as part-settlement towards a

More information

129 KITCHEN BASE CABINET 480

129 KITCHEN BASE CABINET 480 129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house

More information

DAKOTA MANDOLA KIT. MUSICMAKER S KITS, INC PO Box 2117 Stillwater, MN harpkit.com

DAKOTA MANDOLA KIT. MUSICMAKER S KITS, INC PO Box 2117 Stillwater, MN harpkit.com DAKOTA MANDOLA KIT MUSICMAKER S KITS, INC PO Box 2117 Stillwater, MN 55082 651-439-9120 harpkit.com DAKOTA MANDOLA KIT WOOD PARTS: A - Neck B - Fingerboard C - Heel Block D - Tail Block E - Clamping Block

More information

BRACKET FIX SYSTEM FITTING INSTRUCTIONS

BRACKET FIX SYSTEM FITTING INSTRUCTIONS Whether building a new staircase or replacing old banisters, the patented Bracket Fix stair balustrading system will enable you to complete the work quickly and easily. The Richard Burbidge patented Bracket

More information

EXTREME LOAD no. TWO

EXTREME LOAD no. TWO 1602 - EXTREME LOAD no. TWO Kit Features: 22' 4 " x 14' x 3'-6 Oversize Load 49mm (1.9") actual height Bolt Head Details Welded Load Mounting Fins Painting Handles Tools Required: Hobby Knife Tweezers

More information

SURFACE CLIP MOUNT. 1 Insert lens into channel, measure, and cut to length. Remove lens cover from channel. surface. Attach lens cover and end caps

SURFACE CLIP MOUNT. 1 Insert lens into channel, measure, and cut to length. Remove lens cover from channel. surface. Attach lens cover and end caps SURFACE CLIP MOUNT 1 Insert lens into channel, measure, and cut to length Remove lens cover from channel Screw mounting clips into mounting Snap channel into mounting clips Attach lens cover and end caps

More information

Chain Drive Vise. Installation Instructions. (revised 05/04/2016)

Chain Drive Vise. Installation Instructions. (revised 05/04/2016) Chain Drive Vise Installation Instructions (revised 05/04/2016) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step

More information

REVISION LIST CHAPTER 25: AFT WINDOWS. The following list of revisions will allow you to update the Legacy construction manual chapter listed above.

REVISION LIST CHAPTER 25: AFT WINDOWS. The following list of revisions will allow you to update the Legacy construction manual chapter listed above. REVISION LIST CHAPTER 25: The following list of revisions will allow you to update the Legacy construction manual chapter listed above. Under the Action column, R&R directs you to remove and replace the

More information

Trestle Table and Benches Materials List

Trestle Table and Benches Materials List Project 18444EZ: Trestle Table and Benches In the early days of our country, trestle tables were popular because they could easily be disassembled and moved out of the way when not in use no small advantage

More information

3Position the hull of the ship as

3Position the hull of the ship as Yamato: Step-by-step 25 The hull and stern deck c b d a b d c e e f a Rear frame b Stern deck x 2 c Stern deck x 2 d Side wall x 2 Wood glue Sandpaper (no. 400 grain) Craft knife Pliers d Side wall x 2

More information

Coffee table with recessed tray

Coffee table with recessed tray Coffee table with recessed tray Dinner is served Coffee table with recessed tray This coffee table has it all: it contains a recessed tray, so that you can treat your guests to various delicacies. 1 Introduction

More information

This is the paper version of an ArcGIS Online story mapping activity developed in partnership with Esri Canada.

This is the paper version of an ArcGIS Online story mapping activity developed in partnership with Esri Canada. This is the paper version of an ArcGIS Online story mapping activity developed in partnership with Esri Canada. The object of the activity is to plan the building of an acoustic guitar that reflects your

More information

Router Table. Construction

Router Table. Construction Router Table A router table is an invaluable tool. The problem, however, is that ready-built router tables are usually relatively expensive and too narrow for many projects. This router table provides

More information

Chain Drive Vise. Installation Instructions. (revised 11/29/2018)

Chain Drive Vise. Installation Instructions. (revised 11/29/2018) Chain Drive Vise Installation Instructions (revised 11/29/2018) Lie-Nielsen Chain Drive Vise Instructions Table of Contents page About Your Chain Drive Vise 3 Parts List 4 Exploded Parts Diagram 5 step

More information

SAN FELIPE: Step by Step Pack 2

SAN FELIPE: Step by Step Pack 2 Pack 2 Your parts Stern reinforcement Bulkheads The poop deck Bulkhead planks Planks Tools and equipment Knife Pencil Wood glue Sandpaper File a Using leftover 5 x 5-mm wooden strips, measure and cut beams

More information

desde 1979 A tradition in CRAFTMANSHIP

desde 1979 A tradition in CRAFTMANSHIP desde 1979 A tradition in CRAFTMANSHIP Solid Top ARTIST series A tradition in CRAFTMANSHIP The classical guitar is truly a great instrument. Steeped in history with a sound that is instantly recognisable.

More information

guitar Musicmaker s Kits

guitar Musicmaker s Kits GUIT-A-LONG guitar Musicmaker s Kits (Hwy 36 behind Joseph s Restaurant) P.O. Box 2117 Stillwater, MN 55082 (651) 439 9120 info@harpkit.com harpkit.com GUIT-A-LONG GUITAR 1 - Set Assembly Instructions

More information

Model Specifications 2014 Subject to change without notice

Model Specifications 2014 Subject to change without notice MODEL SPECIFICATIONS / FAQ We offer a wide variety of Guitar Packages and Models from which you can choose. Please consult our website for pictures of guitars found on this Specifications sheet. For help

More information

Taylor Guitars Custom Worksheet - 12 Fret - US Dollars - MAP/RRP

Taylor Guitars Custom Worksheet - 12 Fret - US Dollars - MAP/RRP Taylor Guitars Custom Worksheet - 12 Fret - US Dollars - MAP/RRP Store Name Customer Name Prices and Options Valid from October 1, 2017 through December 31, 2017 CATEGORY Guitar Type 12 string 3,100 6

More information

5If the protruding part is. 6Place 1 as is shown in the. 7Place what was assembled

5If the protruding part is. 6Place 1 as is shown in the. 7Place what was assembled Yamato: Step-by-step 49 The base of the bridge and strakes a c b d a Base of the bridge b Base of the bridge c Base of the bridge d Strakes x 10 THE BASE OF THE BRIDGE 1Smooth 1 to 3, first using the metal

More information

Rim Wednesday, January 16, :35 PM

Rim Wednesday, January 16, :35 PM ASL Breakdown Page 1 Rim Wednesday, January 16, 2013 9:35 PM Similar to the plates, begin with the side blanks, determining the "show face" and taper angle. Then make the taper cut. The diagram shows these

More information

Thank you for purchasing a Flaxwood DIY kit

Thank you for purchasing a Flaxwood DIY kit Thank you for purchasing a Flaxwood DIY kit We appreciate your decision to build the most suitable Flaxwood guitar for you. This builder guide will give you detailed information about the kit itself and

More information

136 PLYWOOD DESK 522

136 PLYWOOD DESK 522 136 PLYWOOD DESK 522 Simple in design and inexpensive, this plywood desk is made from a single 4- x 8-foot panel. Plywood is available with many hardwood veneers; it can also be covered with plastic laminate,

More information

Inspection Process Acoustic Guitars

Inspection Process Acoustic Guitars Inspection Process Acoustic Guitars Acoustic and Classical Guitars One of our many goals at FirstGuitar is to set you up for success in developing your skills and enjoyment for a lifetime of music making

More information

Finish Neck and Fretboard Wednesday, January 16, :36 PM

Finish Neck and Fretboard Wednesday, January 16, :36 PM ASL Breakdown Page 1 Finish Neck and Fretboard Wednesday, January 16, 2013 9:36 PM Layer on the fret board, making sure registration pins are in place and everything lays flat. The 3/16" aluminum nutsurrogate

More information

Tools Required. Bench Hardware. Bench Parts. Planter Hardware. Planter Parts. BENCH/PLANTER INSTALLATION GUIDELINES for

Tools Required. Bench Hardware. Bench Parts. Planter Hardware. Planter Parts. BENCH/PLANTER INSTALLATION GUIDELINES for Arbor Collection / Harvest Collection / Terra Collection Page 1 Please read all instructions completely before starting any part of the installation. Each AZEK and Kit comes complete with all hardware,

More information

Bass Guitar Kit J-Style bass electric guitar kit

Bass Guitar Kit J-Style bass electric guitar kit Bass Guitar Kit J-Style bass electric guitar kit user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Strasse 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet:

More information

Bass Guitar Kit P-Style bass electric guitar kit

Bass Guitar Kit P-Style bass electric guitar kit Bass Guitar Kit P-Style bass electric guitar kit user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Strasse 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet:

More information

GENERAL NOTES: Page 1 of 9

GENERAL NOTES: Page 1 of 9 Laminating A Zia Into A Turning Blank by W. H. Kloepping, Jan. 2009 This describes how a zia (the New Mexico state symbol) can be laminated into a turning blank. Materials needed: Square Turning Block

More information

Build your own Drawer unit. D3 / D4

Build your own Drawer unit. D3 / D4 Page1 Build your own Drawer unit. D3 / D4 1: Introduction. This guide will give you the plans, materials and how to information to build your own drawer unit. The dimensions given will fit a D3 or D4,

More information

HOGNOSE PSALTERY KIT Assembly Instructions

HOGNOSE PSALTERY KIT Assembly Instructions HOGNOSE PSALTERY KIT Assembly Instructions WOOD PARTS 1 Plywood Top (Soundhold Pre-Cut) 1 Plywood Bottom 2 Pin Blocks 1 Short Side 1 Long Side 1 Bridge 1 Scrap of Plywood HARDWARE 1 L-Handle Tuning Wrench

More information

Riverboat Banjo Musicmaker's Kits Inc. (One block north of Hwy 36 & behind Joseph s Restaurant)

Riverboat Banjo Musicmaker's Kits Inc. (One block north of Hwy 36 & behind Joseph s Restaurant) Riverboat Banjo Musicmaker's Kits Inc. (One block north of Hwy 36 & behind Joseph s Restaurant) P.O. Box 2117 Stillwater, MN 55082 (651) 439-9120 info@harpkit.com RIVERBOAT BANJO Wooden Parts List: A --

More information

Parts & Tools. O'Cello printing and assembly instructions. o-cello.com

Parts & Tools. O'Cello printing and assembly instructions. o-cello.com The O'Cello is a 3D-printable cello developed by Conor O'Kane, which is free to download and print for personal use. This document will show you how to print and assemble your own O'Cello. For the latest

More information

Hand Saw Try Square Cut-Off Jig Table Vise Scissors Drilling Fixture Drill Press Hand Drill Ruler

Hand Saw Try Square Cut-Off Jig Table Vise Scissors Drilling Fixture Drill Press Hand Drill Ruler Introduction to Technology TOOLS IN TECHNOLOGY GRADE 6 BIGELOW Technology Education MIDDLE SCHOOL Newton, MA 0516 -2- INTRODUCTION This Technology Learning Activity ( TLA) is designed with two major goals

More information

DIY Travel Ukulele Instructions

DIY Travel Ukulele Instructions DIY Travel Ukulele Instructions Foreword Thank you for requesting the instructions to make your very own DIY Travel Ukulele. Before starting the steps to make this instrument, it is recommended that you

More information

Pivot-Door Downdraft Cabinet Plans

Pivot-Door Downdraft Cabinet Plans Pivot-Door Downdraft Cabinet Plans Finished Cabinet Closed Open Exploded View Introduction This simple downdraft-style dust collection cabinet is a great way to keep your shop cleaner and keep your router

More information

English. Violin. Owner s Manual

English. Violin. Owner s Manual English Violin Owner s Manual 1 Thank you for purchasing this fine Yamaha instrument. Before You Start In order to maximize performance, and to ensure safety at all times, we recommend you read through

More information

Assembly instructions

Assembly instructions Nerdy Gurdy Assembly instructions This manual describes how to assemble a Nerdy Gurdy. Go to http://www.nerdygurdy.nl for more info about these instruments. Jaap Brand The Netherlands January 2018 General

More information

TANDY WALKER'S A 2nd CLASS BOMBER 10 to 20. FW:10 Class A Bomber LG. FW:11 Class A Bomber Pylon Primary Sructure

TANDY WALKER'S A 2nd CLASS BOMBER 10 to 20. FW:10 Class A Bomber LG. FW:11 Class A Bomber Pylon Primary Sructure TANDY WALKER'S A 2nd CLASS BOMBER 10 to 20 FW:10 Class A Bomber LG I finished up the landing gear (LG) this morning and shot a couple of pictures for you to see. The first picture shows the LG with 3/32"

More information

Build the Spitfire: Step-By-step. Pack 7 Stages 61-71

Build the Spitfire: Step-By-step. Pack 7 Stages 61-71 Pack 7 Stages 61-71 1 Stage Contents Page Number 61 212-215 62 216-218 63 219-221 64 222-224 65 225-228 66 229-231 67 232-235 68 236-238 69 239-241 70 242-245 71 246-249 Editorial and design by Continuo

More information

Cigar Box Guitar Instructors Guide

Cigar Box Guitar Instructors Guide Building the Cigar Box Guitar Instructors Guide Developed by Building to Teach 1-18-17 Building the Cigar Box Guitar -(c) Building To Teach 2014 Introduction This project really engages students and helps

More information

SE5a Wing Panels rev 1.0

SE5a Wing Panels rev 1.0 SE5a Wing Panels rev 1.0 The top and bottom wings are different. They might look the same but the bottom wing has one less rib and some rib spacing difference. This is due to where the wooden interplane

More information

!! " # $ % & '! ( ) * +, -

!!  # $ % & '! ( ) * +, - !! " # $ % & '! ( ) * +, - North Pegasus This carton contains: (1) Instruction package. Response Curves North Creek Cabinet Handbook North Creek Wiring Guide (2) 6 oz. Rolls of Dacron stuffing. (1) Tube

More information

GTS Music diy-guitar.com

GTS Music diy-guitar.com GTS Music diy-guitar.com SG Style Kit GTS Music 313 Strachan St. Port Hope, Ontario L1A 0C2 Canada sales@diyguitarkits.net Please read these instructions carefully before beginning to build your guitar

More information

GTS Music diy-guitar.com

GTS Music diy-guitar.com GTS Music diy-guitar.com Tele Style Kit GTS Music 313 Strachan St. Port Hope, Ontario L1A 0C2 Canada sales@diyguitarkits.net Please read these instructions carefully before beginning to build your guitar

More information

The image above is intended to give you an idea of what the dovecote will look like when finished.

The image above is intended to give you an idea of what the dovecote will look like when finished. Thank you for buying my book, I hope it is useful and enjoyable in your quest to building your own dovecote. This book will give you step-by step instructions on how to build your own dovecote also included

More information

Kentucky 4H Wood Science Plans Notebook. Plans Level 1

Kentucky 4H Wood Science Plans Notebook. Plans Level 1 Kentucky 4H Wood Science Plans Notebook Plans Level 1 MATERIALS NEEDED: 1 piece wood 3/4" x 2 x 2 1 piece wood 3/4" x 3 x 3 1/2" 1 wooden spring-type clothespin 2-1 1/2" nails 1-1/2 woodscrew Wood Glue

More information

Fretboard Wednesday, January 16, :36 PM

Fretboard Wednesday, January 16, :36 PM ASL Breakdown Page 1 Fretboard Wednesday, January 16, 2013 9:36 PM - - To prepare the fretboard for cutting fret slots: True one edge of the fretboard blank on the jointer. True one of the other edges

More information

Solo ST Style DIY Electric Guitar Kit

Solo ST Style DIY Electric Guitar Kit Solo ST Style DIY Electric Guitar Kit Assembly Manual V 2.0 Copyright 2017 Solo Music Gear. All rights reserved Wiring Diagram for your DIY Guitar Kit All our wiring diagrams are posted on our website

More information

A Day House. A View of One Way to Finish the Exterior of The Day House. Read these instructions all the way through before beginning this project.

A Day House. A View of One Way to Finish the Exterior of The Day House. Read these instructions all the way through before beginning this project. A Day House A View of One Way to Finish the Exterior of The Day House Read these instructions all the way through before beginning this project. General Comments For the purposes of this project, the standard

More information

Taylor Guitars Custom Worksheet - Acoustic, Acoustic/Electric - US Dollars - MAP/RRP

Taylor Guitars Custom Worksheet - Acoustic, Acoustic/Electric - US Dollars - MAP/RRP Taylor Guitars Custom Worksheet - Acoustic, Acoustic/Electric - US Dollars - MAP/RRP Store Name Customer Name Prices and Options Valid from July 1, 2018 through September 30, 2018 CATEGORY Guitar Type

More information

The Future Of Guitar Travel TM

The Future Of Guitar Travel TM The Future Of Guitar Travel TM www.voyageairguitar.com 6752 Preston Ave., Suite E Belair TM Limited Edition Model: Series Name: Body Shape: Neck Material: Body Material: Fingerboard Material: Pickup Type:

More information

CAL-K1 Self-build guitar kit UK Version 1.0

CAL-K1 Self-build guitar kit UK Version 1.0 CAL-K1 Self-build guitar kit 174.460UK Version 1.0 Thank you for buying the CAL-K1 kit. All the wood, hardware and electrical components of a Chord CAL93 guitar are contained in this package. Please read

More information

The Lynda Lyre Kit

The Lynda Lyre Kit The Lynda Lyre Kit 651-439-9120 www.harpkit.com Wood Parts: A Side A B Side B C Soundhole Arch D Tail Strip E Front Panel (Soundboard) F Back Panel G Bridge H Bridge Pad I Bridge Cap J Inner Brace K Kerfing

More information

The Festival Assembly Instructions

The Festival Assembly Instructions The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New

More information

ROOF KIT ASSEMBLY INSTRUCTIONS

ROOF KIT ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS Gable Ends Center Truss (5x7 & larger) Hardware Package Quant. Item 124 screws 123 screws many Finishing nails 1 Torxs bit 1 Locate the two gable ends and also the center truss (supplied

More information

Solo JB Style DIY Electric Bass Guitar Kit

Solo JB Style DIY Electric Bass Guitar Kit Solo JB Style DIY Electric Bass Guitar Kit Assembly Manual JBK-1 V 1.02 Copyright 2011 Solo Music Gear. All rights reserved Materials List Press-fit peghead bushings String Retainer (1 mounting screw included)

More information

Introduction: The model should be assembled following the sequence of the stages of construction described in these instructions.

Introduction: The model should be assembled following the sequence of the stages of construction described in these instructions. Victoria Bestell-Nr. 3082/00 Introduction: The model should be assembled following the sequence of the stages of construction described in these instructions. The laser-cut components are individually

More information

HM OUTDOOR TABLE:HM OUTDOOR TABLE 25/7/08 11:18 AM Page 30

HM OUTDOOR TABLE:HM OUTDOOR TABLE 25/7/08 11:18 AM Page 30 HM080827 OUTDOOR TABLE:HM080827 OUTDOOR TABLE 25/7/08 11:18 AM Page 30 The treated-pine frames of the table and benches are topped with sturdy blackbutt timber. HM080827 OUTDOOR TABLE:HM080827 OUTDOOR

More information

AC50 Enclosure - Thin Edge

AC50 Enclosure - Thin Edge AC50 Enclosure - Thin Edge 2 3/16??? 4 PL 11/16 1 7/8 Piping Groove 2 7/8 Top thickness = 18mm 6 7/16 All other pieces thick Corner Radii and joints =?? Bracing blocks for back = 5/8 square, 2 ea. Back

More information