Welcome to Solid Edge University
|
|
- Estella York
- 5 years ago
- Views:
Transcription
1 #SEU15 Welcome to Solid Edge University Realize innovation.
2 State-of-the-Art Drafting, Made Even Better Investing in What You Need General Workflow Dimension Enhancements Annotation Enhancements Page 2
3 Investing in What You Need Where do you spend most of your time on drawing creation? Drawing View creation and update? Tables? 2D geometry? No? You tell us that you spend most of your time annotating the drawing! Many resources have been applied to enhancing drawing annotation in ST6, ST7, and ST8. This effort will continue into the future to help make you more productive. Page 3
4 General Workflow Empty Text Box and Callout Display Previous display did not show empty Callout and Text Boxes. Can interfere with locate and other workflows. We started displaying these so you can see them and clean them up. They do not print or show up in Save as Image or Save as PDF. My world is falling apart because I don t understand what this is?????? Added options in Solid Edge Options General Tab. Custom error string Page 4
5 General Workflow Clean Up a Drawing (Delete everything but Drawing Views) You may not know. Use CTRL+A to select everything. Press Delete Click No to keep Drawing Views Page 5
6 General Workflow Fence Selection (Directional) Left to Right Fence Inside Entire object must be inside fence to select. Dimensions not selected Page 6
7 General Workflow Fence Selection (Directional) Right to Left Fence Inside and Overlapping Entire object does not need to be inside fence to select. Dimensions are selected Drawing View? Shift click drawing view Or click No when prompted on Delete Page 7
8 Dimension Alignment Sets Collections of dimensions that are aligned (chain and/or stack). Alignment creation can be toggled on/off. Toggling off does not dissolve any existing dimension alignment sets. Page 8
9 Dimension Alignment Sets Collections of dimensions that are aligned (chain and/or stack). (ST5) Chain Dimensions Drag as single set (ST5) Stack Dimensions Drag as single set Page 9
10 Dimension Alignment Sets Collections of dimensions that are aligned (chain and/or stack). (ST6) Combination Chain and Stack Dimensions Drag as single set Hybrid Set Both Chain and Stack Page 10
11 Dimension Alignment Sets Dimension Alignment Indicator Disjoint Chain Set Create dimension by geometry and then align with existing chain. Don t select existing chain first and then select geometry. Page 11
12 Dimension Alignment Sets Pure Stack Set with only stacked dimensions. Insert into Pure Stack Select stack to insert dimension and then select geometry to dimension. Automatically adjusts stack Page 12
13 Dimension Alignment Sets Hybrid Set Take care when working with hybrid sets. Stack dimensions on left and continue with dimensions on right. Symmetry is recognized and will chain with like dimensions. Page 13
14 Dimension Alignment Sets Hybrid Set Take care when working with hybrid sets. Adding a dimension directly into a Stack Set will stack the dimensions by size. No symmetry case Page 14
15 Dimension Alignment Sets Hybrid Set Take care when working with hybrid sets. Create the dimension by geometry and then align with the existing set. Don t select set first and expect proper alignment. Page 15
16 Dimension Alignment Sets Split Alignment Set Split the set at selected dimension. Break Alignment Set Dissolve the Alignment Set Page 16
17 Dimension Alignment Sets Remove from Alignment Set Single Dimension Multiple Dimensions Creates new set from selected dimensions Page 17
18 Dimension Alignment Sets Arrange Dimensions Before After Page 18
19 Dimension Orientation Trick Question? What is a Smart Dimension? Anyone? There is no such thing as a Smart Dimension. Smart Dimension is a command that places many different dimension types based on the geometry selected. Page 19
20 Dimension Orientation Bringing consistency between Smart Dimension and Distance Between. Smart Dimension Enable Orientation Selection Use the prompt bar in both commands. shift =horizontal/vertical Toggle between by 2 points and horizontal/vertical while placing a linear dimension. Page 20
21 Dimension Orientation Bringing consistency between Smart Dimension and Distance Between. Smart Dimension Enable Orientation Selection Status Bar will tell you which dimension type is being placed. Page 21
22 Concentric Diameter Alignment New radial dimension type button on Smart Dimension Command bar Read the prompt Use d to cycle through Radius, Diameter, and Concentric Diameter. Concentric Diameter Dimension Forces radial dimensions to concentric diameter. Enables the creation of alignment sets for concentric diameter dimensions Page 22
23 Concentric Diameter Alignment Button forces radial dimensions to concentric diameter. Enables the creation of alignment sets for concentric diameter dimensions. Dimensions stack automatically as you go. Page 23
24 Concentric Diameter Alignment Automatically inserts into and adjusts the stack as you go. Page 24
25 Concentric Diameter Alignment Alternating text positions for readability Automatically adjusts within stack Page 25
26 Coordinate Dimensions Improved Creation Workflow Fewer Clicks for Measure Dimensions Emphasize Alignment Improved Display Control Dimension Style and Dimension Properties Perpendicular Text (New default) Allow negative values Allow origin value change Applies change to measure dimensions Improved Dimension Line Length and Handles Shortened Dimension Line Drag Dimension Line to reposition Improved Jogging Automatic jog during placement ALT+Drag text to add jog Will also jog adjacent dimensions Improved Drag Behavior Drag any dimension line to reposition all aligned dimension lines Page 26
27 Coordinate Dimensions Improved Placement Workflow Dimension style and Properties Lines and Coordinate Tab Place Origin Dimension Single Click Geometry For Measure Dimension Dimension Added and Jogged, No Second Click Page 27 Single Click Geometry For Measure Dimension Dimension Added and Jogged, No Second Click
28 Coordinate Dimensions Place many coordinate dimensions at one time. Automatic Coordinate Dimension Command Set filter for circle center points only. Select drawing view to find circles. Cursor position defines dimension orientation. Select by Drawing View Selection by drawing view or by geometry Filter keypoints to dimension Page 28 Select by Geometry
29 Dimension Modify Enhancements More Handle Points for Modification 3 Classes of Handles Connect Handles Modify Handles Secondary Modify Handles Terminator Shortcut Menu Terminator Type Show Projection Line Show Dimension Line Flip Terminator Page 29
30 Annotations Annotation Modify Enhancements More Handle Points for Modification Consistent Handle Points 3 Classes of Handles Connect Handles Modify Handles Secondary Modify Handles Terminator Shortcut Menu Terminator Type Leader Orientation Snap Lines 45 and 90 Degree Orientations Page 30
31 Annotations Drawing View Annotation Modify Enhancements Drawing View Annotation Modify Improvements Cutting Plane Line More Modify Handles Flip Direction on Shortcut Menu View Plane Line More Modify Handles Secondary Modify Handle to Drag Anywhere No Keyboard Input Needed Detail Envelope ANSI Style Text Orientation Snap Lines Page 31
32 Annotations Change Leader and Break Line Connect Position (ST5) Leader connect position easily changed Use handle at connect position Read the prompt! Alt+drag the break line handle point to snap to keypoints." Lines display snap orientations at each keypoint. Drop at desired keypoint and orientation. Page 32
33 Annotations Reference Text Used to extract text from annotations to be inserted into other annotations. E.g. Feature Control Frame has a reference text that refers to the Datum Frame text A. If A is changed in Datum Frame, then that Feature Control Frame will update automatically. Page 33
34 Annotations Reference Text Can be from following source annotations: Callout Balloon Datum Frame Datum Target Drawing View Drawing View Annotations Look for the Reference Text button on annotation UI. E.g. %{Balloon Upper Ref:A256} means a reference to the Upper text in a Balloon with an ID of A256. Page 34
35 Annotations Annotation Value Formatting Have you ever wondered how to easily find the codes for formatting values in annotations? Round-off No units /NU Dual Units /DU Etc. Go to Help and search for format codes How can I make this easier? Page 35
36 Annotations Annotation Value Formatting Underline and highlight property text and 2-letter codes when cursor is within text. Page 36
37 Annotations Annotation Value Formatting Look for the Format button on the available annotations. Page 37
38 Annotations Annotation Value Formatting Format the property text through the Format Values dialog. No Units and Dual Units Round-off Date-time Text case Tolerance UI enabled or disabled based on property selected. Page 38
39 What s Next? Whatever you collectively tell us! Always more to come. Thank You! Page 39
40 Contact Ricky Black Product Manager (Drafting and PMI) Solid Edge Planning 675 Discovery Drive Huntsville, Al Phone: (256) Fax: (256) Realize innovation. Page 40
Appendix R5 6. Engineering Drafting. Broken View
Updating Using Autodesk Inventor to Release 5 Appendix R5 6 Engineering Drafting Chapter 6 delineates the concepts of engineering drafting. You output orthographic views from solid parts and orthographic
More informationDRAFT Solid Edge ST4 Update Training Draft
DRAFT Solid Edge ST4 Update Training Draft Presented by: Steve Webb Topics Parts List Table Titles Column Headers Headers Merging Header Rotate Cell Aspect Ratio Cell Formatting Overriding Disabled Cells
More information#SEU Welcome! Solid Edge University 2016
#SEU 2016 Welcome! Solid Edge University 2016 Realize innovation. Drawing View Creation Under the Hood (Part 4) Realize innovation. Drawing View Creation Under the Hood (Part 4) Realize innovation. Drawing
More informationGetting started with. Getting started with VELOCITY SERIES.
Getting started with Getting started with SOLID EDGE EDGE ST4 ST4 VELOCITY SERIES www.siemens.com/velocity 1 Getting started with Solid Edge Publication Number MU29000-ENG-1040 Proprietary and Restricted
More informationUser Guide V10 SP1 Addendum
Alibre Design User Guide V10 SP1 Addendum Copyrights Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement or
More informationGenerative Drafting (ISO)
CATIA Training Foils Generative Drafting (ISO) Version 5 Release 8 January 2002 EDU-CAT-E-GDRI-FF-V5R8 1 Table of Contents (1/2) 1. Introduction to Generative Drafting Generative Drafting Workbench Presentation
More informationGetting Started. Before You Begin, make sure you customized the following settings:
Getting Started Getting Started Before getting into the detailed instructions for using Generative Drafting, the following tutorial aims at giving you a feel of what you can do with the product. It provides
More informationIntroduction to ANSYS DesignModeler
Lecture 4 Planes and Sketches 14. 5 Release Introduction to ANSYS DesignModeler 2012 ANSYS, Inc. November 20, 2012 1 Release 14.5 Preprocessing Workflow Geometry Creation OR Geometry Import Geometry Operations
More informationTo start a new drawing Select File New then from the dialog box, which appears select Normal.dft followed by OK.
Draft Tutorial This tutorial provides step-by-step instructions for the detailing of a drawing of the anchor block shown opposite. As you create this drawing, you will use the following drafting techniques:
More information1.6.7 Add Arc Length Dimension Modify Dimension Value Check the Sketch Curve Connectivity
Contents 2D Sketch... 1 1.1 2D Sketch Introduction... 1 1.1.1 2D Sketch... 1 1.1.2 Basic Setting of 2D Sketch... 2 1.1.3 Exit 2D Sketch... 4 1.2 Draw Common Geometry... 5 2.2.1 Points... 5 2.2.2 Lines
More informationAn Introduction to Dimensioning Dimension Elements-
An Introduction to Dimensioning A precise drawing plotted to scale often does not convey enough information for builders to construct your design. Usually you add annotation showing object measurements
More informationDimensioning. Subject Matters:
Objectives: To define dimensioning. To recognise the different types of dimensions. To define and create a dimension style. To recognise the dimension toolbar and the dimensioning commands. To create dimensions
More informationGstarCAD Mechanical 2015 Help
1 Chapter 1 GstarCAD Mechanical 2015 Introduction Abstract GstarCAD Mechanical 2015 drafting/design software, covers all fields of mechanical design. It supplies the latest standard parts library, symbols
More informationAutoDesk Inventor: Creating Working Drawings
AutoDesk Inventor: Creating Working Drawings Inventor allows you to quickly and easily make quality working drawings from your 3D models. This tutorial will walk you through the steps in creating a working
More informationGeometry Controls and Report
Geometry Controls and Report 2014 InnovMetric Software Inc. All rights reserved. Reproduction in part or in whole in any way without permission from InnovMetric Software is strictly prohibited except for
More informationWelcome to SPDL/ PRL s Solid Edge Tutorial.
Smart Product Design Product Realization Lab Solid Edge Assembly Tutorial Welcome to SPDL/ PRL s Solid Edge Tutorial. This tutorial is designed to familiarize you with the interface of Solid Edge Assembly
More informationRadial dimension objects are available for placement in the PCB Editor only. Use one of the following methods to access a placement command:
Radial Dimension Old Content - visit altium.com/documentation Modified by on 20-Nov-2013 Parent page: Objects A placed Radial Dimension. Summary A radial dimension is a group design object. It allows for
More informationSet your drafting standard and drawing preferences
DRAFTING The Drafting application is designed to allow you to produce and maintain industry standard engineering drawings directly from the 3D model or assembly part. Drawings created in the Drafting application
More informationActivity 1 Modeling a Plastic Part
Activity 1 Modeling a Plastic Part In this activity, you will model a plastic part. When completed, your plastic part should look like the following two illustrations. While building this model, take time
More informationLesson 4 Holes and Rounds
Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information
More informationPublication Number spse01510
Sketching Publication Number spse01510 Sketching Publication Number spse01510 Proprietary and restricted rights notice This software and related documentation are proprietary to Siemens Product Lifecycle
More informationArchitecture 2012 Fundamentals
Autodesk Revit Architecture 2012 Fundamentals Supplemental Files SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Tutorial files on enclosed CD Visit
More informationEngineering Technology
Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,
More informationIntroduction to Autodesk Inventor for F1 in Schools (Australian Version)
Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital
More informationLesson 4 Extrusions OBJECTIVES. Extrusions
Lesson 4 Extrusions Figure 4.1 Clamp OBJECTIVES Create a feature using an Extruded protrusion Understand Setup and Environment settings Define and set a Material type Create and use Datum features Sketch
More informationLesson 6 2D Sketch Panel Tools
Lesson 6 2D Sketch Panel Tools Inventor s Sketch Tool Bar contains tools for creating the basic geometry to create features and parts. On the surface, the Geometry tools look fairly standard: line, circle,
More informationVirtual components in assemblies
Virtual components in assemblies Publication Number spse01690 Virtual components in assemblies Publication Number spse01690 Proprietary and restricted rights notice This software and related documentation
More informationRelease Highlights for BluePrint-PCB Product Version 2.0.1
Release Highlights for BluePrint-PCB Product Version 2.0.1 Introduction BluePrint Version 2.0.1 is a rolling release for BluePrint V2.0. BluePrint rolling releases are delivered as needed and allow us
More informationWorking With Drawing Views-I
Chapter 12 Working With Drawing Views-I Learning Objectives After completing this chapter you will be able to: Generate standard three views. Generate Named Views. Generate Relative Views. Generate Predefined
More informationTable of Contents. Lesson 1 Getting Started
NX Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard
More information5 More Than Straight Lines
5 We have drawn lines, shapes, even a circle or two, but we need more element types to create designs efficiently. A 2D design is a flat representation of what are generally 3D objects, represented basically
More informationDesigning in the context of an assembly
SIEMENS Designing in the context of an assembly spse01670 Proprietary and restricted rights notice This software and related documentation are proprietary to Siemens Product Lifecycle Management Software
More informationNX9 Manual Drafting. BINDE Training
Extract of 82 pages NX9 Manual Drafting Drafting K Table of contents 1 K - Drafting K1 Start Drafting K1-1 Create Drawing K1-3 Drawing Navigator K1-4 Drafting Ribbon Bar K2 Drawing Sheet K3 Views K3-1
More informationAutoCAD Civil 3D 2009 ESSENTIALS
AutoCAD Civil 3D 2009 ESSENTIALS SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower Prices. Alignments and Profiles Section 2: Profiles In this section you learn how
More informationAEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.
AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and
More informationAlternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.
Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.
More information1 Sketching. Introduction
1 Sketching Introduction Sketching is arguably one of the more difficult techniques to master in NX, but it is well-worth the effort. A single sketch can capture a tremendous amount of design intent, and
More information1: INTRODUCTION TO AUTOCAD
AutoCAD syllabus 1: INTRODUCTION TO AUTOCAD Starting AutoCAD AutoCAD Screen Components Drawing Area Command Window Navigation bar Status bar Invoking Commands in AutoCAD Keyboard Ribbon Application Menu
More informationPart 2: Earpiece. Insert Protrusion (Internal Sketch) Hole Patterns Getting Started with Pro/ENGINEER Wildfire. Round extrusion.
Part 2: Earpiece 4 Round extrusion Radial pattern Chamfered edge To create this part, you'll use some of the same extrusion techniques you used in the lens part. The only difference in this part is that
More informationRhinoceros modeling tools for designers. Using Layouts in Rhino 5
Rhinoceros modeling tools for designers Using Layouts in Rhino 5 RH50-TM-LAY-Apr-2014 Rhinoceros v5.0, Layouts, Training Manual Revised April 8, 2014, Mary Fugier mary@mcneel.com Q&A April 8, 2014, Lambertus
More informationAlibre Vault Integration Automatic Check-in Prompt Sheet Metal Lofted Flanges & Assembly Constraints Sheet Metal Parameters
1 TABLE OF CONTENTS General User Interface... 5 User Interaction Consistency... 5 Ctrl and Shift Behaviors... 5 Right-Click Behavior... 5 Dragging the Dog Bone... 6 Apply Button Added to Dialogs... 6 Missing
More information1. Create a 2D sketch 2. Create geometry in a sketch 3. Use constraints to position geometry 4. Use dimensions to set the size of geometry
2.1: Sketching Many features that you create in Fusion 360 start with a 2D sketch. In order to create intelligent and predictable designs, a good understanding of how to create sketches and how to apply
More informationAUTODESK INVENTOR Trial Projects
AUTODESK INVENTOR Trial Projects Drawing Creation Create detailed drawings of a collar flange PART 1: CREATING DRAWING VIEWS page: 2 1. 2. 3. Start by clicking the Projects icon in the ribbon. Navigate
More informationOn completion of this exercise you will have:
Prerequisite Knowledge To complete this exercise you will need; to be familiar with the SolidWorks interface and the key commands. basic file management skills the ability to rotate views and select faces
More information06/17/02 Page 1 of 12
Understanding the Graphical User Interface When you start AutoCAD, the AutoCAD window opens. The window is your design work space. It contains elements that you use to create your designs and to receive
More informationCreo Parametric 2.0: Introduction to Solid Modeling. Creo Parametric 2.0: Introduction to Solid Modeling
Creo Parametric 2.0: Introduction to Solid Modeling 1 2 Part 1 Class Files... xiii Chapter 1 Introduction to Creo Parametric... 1-1 1.1 Solid Modeling... 1-4 1.2 Creo Parametric Fundamentals... 1-6 Feature-Based...
More informationAutodesk AutoCAD 2013 Fundamentals
Autodesk AutoCAD 2013 Fundamentals Elise Moss SDC P U B L I C AT I O N S Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following websites to learn more
More informationCreo: Hole, Fillet, and Round Layout/Dimension Tutorial. By: Matthew Jourden Brighton High School
Creo: Hole, Fillet, and Round Layout/Dimension Tutorial Layout of a Part with Holes 1. Open a blank drawing with your border and title block By: Matthew Jourden Brighton High School 2. Place the front,
More informationAutoCAD 2018 Fundamentals
Autodesk AutoCAD 2018 Fundamentals Elise Moss SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn more about
More informationCreo Parametric Primer
Creo Parametric Primer Creo Parametric Primer Education Editions 2 C2-SE-L1-004-1.0 Written by Tim Brotherhood and Adam Haas Conditions of use Acknowledgements Feedback tbrotherhood@ptc.com Product code
More informationSolidWorks 95 User s Guide
SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents
More informationChapter 1. Creating, Profiling, Constraining, and Dimensioning the Basic Sketch. Learning Objectives. Commands Covered
Chapter 1 Creating, Profiling, Constraining, and Dimensioning the Basic Sketch Learning Objectives After completing this chapter, you will be able to: Draw the basic outline (sketch) of designer model.
More informationCREO.1 MODELING A BELT WHEEL
CREO.1 MODELING A BELT WHEEL Figure 1: A belt wheel modeled in this exercise. Learning Targets In this exercise you will learn: Using symmetry when sketching Using pattern to copy features Using RMB when
More informationSolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI
SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered
More informationTechnical What s New. AutoCAD. Mechanical 2011
AutoCAD Mechanical 2011 Welcome to AutoCAD Mechanical 2011 Contents Content Library...3 General Enhancements...3 Localization...3 Improved International Standards...3 Update Content Selectively...3 Part
More informationGEN20604 Intelligent AutoCAD Model Documentation Made Easy
GEN20604 Intelligent AutoCAD Model Documentation Made Easy David Cohn 4D Technologies Learning Objectives Learn how to create base views and projected views from 3D models Learn how to create and control
More informationMesh density options. Rigidity mode options. Transform expansion. Pin depth options. Set pin rotation. Remove all pins button.
Martin Evening Adobe Photoshop CS5 for Photographers Including soft edges The Puppet Warp mesh is mostly applied to all of the selected layer contents, including the semi-transparent edges, even if only
More informationIntroduction. Parametric Design
Introduction This text guides you through parametric design using Creo Parametric. While using this text, you will create individual parts, assemblies, and drawings. Parametric can be defined as any set
More informationTutorial 3: Drawing Objects in AutoCAD 2011
Tutorial 3: Drawing Objects in AutoCAD 2011 Audience: Users new to AutoCAD Prerequisites: None Time to complete: 15 minutes In This Tutorial Please complete the lessons in this tutorial in order. The earlier
More informationCreo Parametric Primer
Creo Parametric Primer Creo Parametric Primer Education Editions C1-SE-L1-004-1.0 Written by Tim Brotherhood and Adam Haas Conditions of use Acknowledgements Feedback tbrotherhood@ptc.com Product code
More informationMETBD 110 Hands-On 17 Dimensioning Sketches
METBD 110 Hands-On 17 Dimensioning Sketches Why: Recall, Pro/E can capture design intent through the use of geometric constraints, dimensional constraints, and parametric relations. Dimensional constraints
More informationStep-by-Step Tutorial: Applying Dimensional Constraints
New Commands in AutoCAD 2010: Part 1 Dimensional Constraints, Part 1 by Ralph Grabowski Introduction One of the really significant new features of AutoCAD 2010 is parametric drafting. This technology allows
More informationDrawing and Detailing with SolidWorks 2014
r n fo io n at io c at tifi ar er ep c pr WT es D R u d Pcl In C S W e th W E N Drawing and Detailing with SolidWorks 2014 Referencing the ASME Y14 Engineering Drawing and Related Documentation Practices
More informationAdvance Dimensioning and Base Feature Options
Chapter 4 Advance Dimensioning and Base Feature Options Learning Objectives After completing this chapter you will be able to: Dimension the sketch using the autodimension sketch tool. Dimension the sketch
More informationAutoCAD Tutorial First Level. 2D Fundamentals. Randy H. Shih SDC. Better Textbooks. Lower Prices.
AutoCAD 2018 Tutorial First Level 2D Fundamentals Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to
More informationModeling Basic Mechanical Components #1 Tie-Wrap Clip
Modeling Basic Mechanical Components #1 Tie-Wrap Clip This tutorial is about modeling simple and basic mechanical components with 3D Mechanical CAD programs, specifically one called Alibre Xpress, a freely
More informationAutodesk Inventor Module 17 Angles
Inventor Self-paced ecourse Autodesk Inventor Module 17 Angles Learning Outcomes When you have completed this module, you will be able to: 1 Describe drawing inclined lines, aligned and angular dimensions,
More informationPart Design Fundamentals
Part Design Fundamentals 1 Course Presentation Objectives of the course In this course you will learn basic methods to create and modify solids features and parts Targeted audience New CATIA V5 Users 1
More informationAdvance Steel. Tutorial
Advance Steel Tutorial Table of contents About this tutorial... 7 How to use this guide...9 Lesson 1: Creating a building grid...10 Step 1: Creating an axis group in the X direction...10 Step 2: Creating
More informationMastering AutoCAD 2D
Course description: Mastering AutoCAD 2D Design and shape the world around you with the powerful, flexible features found in AutoCAD software, one of the world s leading 2D design applications. With robust
More informationAECOsim Building Designer. Quick Start Guide. Chapter 2 Making the Mass Model Intelligent Bentley Systems, Incorporated.
AECOsim Building Designer Quick Start Guide Chapter 2 Making the Mass Model Intelligent 2012 Bentley Systems, Incorporated www.bentley.com/aecosim Table of Contents Making the Mass Model Intelligent...3
More informationIntroduction to CATIA V5
Introduction to CATIA V5 Release 17 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower
More informationAutoCAD 2020 Fundamentals
Autodesk AutoCAD 2020 Fundamentals ELISE MOSS Autodesk Certified Instructor SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
More informationDrawing with precision
Drawing with precision Welcome to Corel DESIGNER, a comprehensive vector-based drawing application for creating technical graphics. Precision is essential in creating technical graphics. This tutorial
More informationGenerative Drafting Overview What's New Getting Started User Tasks
Generative Drafting Overview Conventions What's New Getting Started Defining the Drawing Sheet Part Drawing Opening a Part Creating a Front View Creating a Projection View Creating a Section View Creating
More informationAutoCAD LT 2012 Tutorial. Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS. Schroff Development Corporation
AutoCAD LT 2012 Tutorial Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation AutoCAD LT 2012 Tutorial 1-1 Lesson 1 Geometric Construction
More informationCreo Revolve Tutorial
Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate
More informationCreo Parametric Primer
PTC Creo Parametric - Primer Student and Academic Editions 02 Helpful hints are enclosed in red brackets or round bubbles like this one! Creo Parametric Primer THIS VERSION OF THE CREO PRIMER HAS BEEN
More informationAECOsim Building Designer. Quick Start Guide. Chapter A08 Space Planning Bentley Systems, Incorporated
AECOsim Building Designer Quick Start Guide Chapter A08 Space Planning 2012 Bentley Systems, Incorporated www.bentley.com/aecosim Table of Contents Space Planning...3 Sketches... 3 SpacePlanner... 4 Create
More informationPart 8: The Front Cover
Part 8: The Front Cover 4 Earpiece cuts and housing Lens cut and housing Microphone cut and housing The front cover is similar to the back cover in that it is a shelled protrusion with screw posts extruding
More informationQuick Start for Autodesk Inventor
Quick Start for Autodesk Inventor Autodesk Inventor Professional is a 3D mechanical design tool with powerful solid modeling capabilities and an intuitive interface. In this lesson, you use a typical workflow
More informationToothbrush Holder. A drawing of the sheet metal part will also be created.
Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson; Sketch (Line, Centerline, Circle, Add Relations, Smart Dimension,), Extrude Boss/Base, and Edit
More informationStarting a 3D Modeling Part File
1 How to Create a 3D Model and Corresponding 2D Drawing with Dimensions, GDT (Geometric Dimensioning and Tolerance) Symbols and Title Block in SolidWorks 2013-2014 By Edward Locke This tutorial will introduce
More informationGetting Started with. Vectorworks Architect
Getting Started with Vectorworks Architect Table of Contents Introduction...2 Section 1: Program Installation and Setup...6 Installing the Vectorworks Architect Program...6 Exercise 1: Launching the Program
More informationRelative Coordinates
AutoCAD Essentials Most drawings are created using relative coordinates. This means that the next point is set from the last point drawn. The last point drawn is stored as temporary 0,0". AutoCAD uses
More informationEngineering Innovation Center Fabrication Shop Basic CAD Training
Engineering Innovation Center Fabrication Shop Basic CAD Training Introduction The Engineering Innovation Center Fabrication Shop was established for support of undergraduate student course work. Every
More informationCreate Compelling 2D Sections, Details, and Auxiliary Views from AutoCAD 3D Models
GEN20552-L Create Compelling 2D Sections, Details, and Auxiliary Views from AutoCAD 3D Models J.C. Malitzke Digital JC CAD Learning Objectives Learn how to create drawing views of AutoCAD 3D models for
More informationAutoCAD 2D I. Module 16. Isometric and Dimensioning. IAT Curriculum Unit PREPARED BY. January 2011
AutoCAD 2D I Module 16 Isometric and Dimensioning PREPARED BY IAT Curriculum Unit January 2011 Institute of Applied Technology, 2011 Module 16 Auto CAD Self-paced Learning Modules AutoCAD 2D Isometric
More informationEvaluation Chapter by CADArtifex
The premium provider of learning products and solutions www.cadartifex.com EVALUATION CHAPTER 2 Drawing Sketches with SOLIDWORKS In this chapter: Invoking the Part Modeling Environment Invoking the Sketching
More informationFunctional Tolerancing and Annotations
Functional Tolerancing and Annotations Preface Getting Started Basic Tasks Advanced Tasks Workbench Description Customizing Glossary Index Dassault Systèmes 1994-2000. All rights reserved. Preface CATIA
More informationPrinciples and Practice
Principles and Practice An Integrated Approach to Engineering Graphics and AutoCAD 2011 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation
More informationVCS SKETCH User Group Meeting
VCS SKETCH 2009 User Group Meeting From Field To Finished in CAMAvision Accessing Sketch in Parcel Maintenance To get started with Sketch open CAMAvision enter Parcel Maintenance and load the parcel you
More informationLearning Guide. ASR Automated Systems Research Inc. # Douglas Crescent, Langley, BC. V3A 4B6. Fax:
Learning Guide ASR Automated Systems Research Inc. #1 20461 Douglas Crescent, Langley, BC. V3A 4B6 Toll free: 1-800-818-2051 e-mail: support@asrsoft.com Fax: 604-539-1334 www.asrsoft.com Copyright 1991-2013
More informationAssignment 12 CAD Mechanical Part 2
Assignment 12 CAD Mechanical Part 2 Objectives In this assignment you will learn to apply the hidden lines, isometric snap, and ellipses commands along with commands previously learned.. General Hidden
More informationLesson 16 Helical Sweeps and Annotations
Lesson 16 Helical Sweeps and Annotations Figure 16.1 Helical Compression Spring Drawing OBJECTIVES Create a helical compression spring with a Helical Sweep Use sweeps to create hooks on extension springs
More informationGetting Started with. Vectorworks Architect
Getting Started with Vectorworks Architect Table of Contents Introduction...2 Section 1: Program Installation and Setup...6 Installing the Vectorworks Architect Program...6 Exercise 1: Launching the Program
More informationSolidWorks Training. Introductory course for staff and students from the School of Physics and Astronomy
SolidWorks Training Introductory course for staff and students from the School of Physics and Astronomy i) Introductory presentation SolidWorks Training ii) The SolidWorks GUI The SolidWorks Graphical
More informationAutodesk AutoCAD 2012: Fundamentals. Elise Moss. autodesk authorized publisher SDC PUBLICATIONS
Autodesk AutoCAD 2012: Fundamentals Elise Moss autodesk authorized publisher SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Autodesk AutoCAD 2012: Fundamentals Lesson 3.0 Drawing
More informationwith Creo Parametric 4.0
Parametric Modeling with Creo Parametric 4.0 An Introduction to Creo Parametric 4.0 NEW Contains a new chapter on 3D Printing Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com
More information