Creo Extrude Tutorial 3: Hole, Fillets and Rounds
|
|
- Carmella Burns
- 2 years ago
- Views:
Transcription
1 Creo Extrude Tutorial 3: Hole, Fillets and Rounds By: Matthew Jourden Brighton High School 1. Open Creo Parametric 2. File > Open > extrudetutorial (From Creo Extrude Tutorial 1) NOTE: Minimum of 2 other extrudes were added to this part. NOTE: Color may have been added to the part as well. See the following steps to remove color 3. Optional: Remove Color a. If image has color like the following and color would like to be removed b. Select Render Tab > Click down arrow below Appearance Gallery > Select Clear Appearances > Clear All Appaearnces > Yes (This will turn the part back to default grey)
2 4. Suppress Features: suppressed features will hide the feature on the part without deleting it. This allows the user to hide a feature(s) a. Select the Features user created from Tutorial 2 > Right Mouse Button; Select Suppress > Feature will disappear from the model tree. (NOTE: Include Extrude 2, 3 and the other extrudes created by the user) NOTE: Any features that reference the suppressed feature will also suppress b. Showing suppressed features on Model Tree Select Settings Menu from the Model Tree (Icon > Check Suppressed Features from pop up menu > Click OK Check Suppressed Objects c. Suppress all features except for Extrude 1 d. Suppressed objects will appear and have a Black Box Next to the Feature Type. e. To unsuppress object Right Mouse Button on Feature > Select Resume.
3 4. Reference: Dimension Values for Arced Shapes a. Holes will need 3 Dimensions i. 2 Locators: Measuring from an Edge to the Center of the Hole ii. Leader Line showing Diameter of Hole Diameter NOTE: Two arrowheads represent a diameter dimension. Locators Single Arrowhead represents radius (See Below) b. Fillets and Rounds: Measured in radius i. Fillets = Inside Edges (Adds material from on a corner) ii. Rounds = Exterior Edges (Subtracts material from on a corner) Fillet Round
4 5. Creating a Hole Two methods to creating a Simple hole i. Extrude ii. Hole Tool a. Hole Creation: Extrude Tool iii. Select Extrude > Select the shown surface iv. Select Circle Tool > Draw Circle on the surface > Notice the software provides locators and diameter. Locators should always measure to the center of a hole for accuracy purposes. Software will allow user to create a dimension tangent to the edge of a circle. Avoid this at all times. To ensure dimensions goes to the center of a hole Select the Center Point of the hole (NOT the edge). > Set the dimensions as shown v. Green Check the Sketch > Set Extrude distance to.500 vi. Select Flip to send the extrude distance into the part cutting material
5 b. Hole Creation: Hole Tool i. Select Model Tab > Select Hole Tool > Select same surface as the Extrude Hole Adjust Diameter. Can also select the dimensional value to type in desired size. Can also adjust size in the Hole Info Bar the Green Anchors set the locators for hole. Set them in the following Locations. Hold Left Mouse Button on Green Anchor > Drag to edge to be measured from. To change Double Click on Values to change dimensional Vale Adjust Height of Hole. Can also select the dimensional value to type in desired size. Can also adjust size in the Hole Info Bar Thread Representation Creates Counterbore and Countersink Holes Simple hole Diameter of Hole Height of Hole Adjust Locator Dimensions
6 ii. Set Hole Dimensions to the following iii. Green Check to set hole c. Add a hole in the following location use Hole or Extrude Tool
7 6. Creating Fillets and Rounds a. Select Model Tab > Select Round Tool (NOTE: Round Tool will create Rounds and Fillets.) Radius of Arc Groups Edges together for same radius size. Hold CTRL Key to have edges part of the same SET
8 b. Select the following Edges (Green Edges) with a Radius of.375 (Hold Control (CTRL) Key while selecting c. Start a New set i. Select New Set from Set Menu in Round Info Bar ii. Let Go of Control (CTRL) Key select an edge and repress Control (CTRL) Key to group other edge with the new Set. iii. Select the following Edge (Green Edge) with a Radius of.25 Save File
9 6. Creating an Arc Feature a. Select Extrude > Select Bottom Surface of Part Reference Edges Bottom Surface of Part Using Line Tool Draw a Line on this Edge from End Point to Endpoint b. Draw a Line Shown below from point to point > Select Line > Right Mouse Button Select Construction Construction Line creates a line that is for Reference based on a Line Drawn. This line will not print or be part of the closed profile. Draw a line connecting these two points > Right Mouse Button > Construction
10 c. Select Circle Tool > Place Cursor at the Midpoint (An M should appear) of the construction Line > Left Click and Place Cursor to the endpoint of the part (This will form a tangent point (circle and a line share one point)) Creating a arc/circle that is the same size as the part. NOTE: This scenario the diameter of the circle does not need to be stated since we used the reference lines as the end points of the circle/arc Mid-Point of Construction Line a. Option 1: Leave the full circle and extrude material inside of material b. Option 2: Cut the circle/arc into the desired number of degrees.
11 d. Green Check > Set Extrude distance to 1.00 > Make sure the material is adding up into the part. Notice how the arc fills in the hole: Chose Option 1 from above NOTE: If the Back Arc Fills in the Hole on the side; there are two options to fix it Option 1: Cut the Back Arc in half so it only extrudes solid material into air (See Option 2 from previous page when building arc) Option 2: Reorder Model Tree: by Holding Left mouse key and dragging the Extrude for the arc above the extrude/hole tool for the hole Select Feature that is the arc Hold Left Mouse Key to drag Arc above the hole feature Let go of Left mouse button to place feature
12 Completed Part Save Part Design Solid Model 11, 12, and 13
Creo: Hole, Fillet, and Round Layout/Dimension Tutorial. By: Matthew Jourden Brighton High School
Creo: Hole, Fillet, and Round Layout/Dimension Tutorial Layout of a Part with Holes 1. Open a blank drawing with your border and title block By: Matthew Jourden Brighton High School 2. Place the front,
Creo Extrude Tutorial 2: Cutting and Adding Material
Creo Extrude Tutorial 2: Cutting and Adding Material 1. Open Creo Parametric 2. File > Open > extrudeturial (From Creo Extrude Tutorial 1) 3. Cutting Material a. Click Extrude Icon > Select the following
Creo Revolve Tutorial
Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate
Nut and Bolt Tutorial
Thread Representations Nut and Bolt Tutorial Parts to a Thread Thread Dimensioning Major Diameter Thread Series (IE UNC, UNF, ACME, etc) ½ - 13 UNC 2 A or B A = External B = Internal Threads per Inch Class
Lesson 4 Holes and Rounds
Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information
Activity 1 Modeling a Plastic Part
Activity 1 Modeling a Plastic Part In this activity, you will model a plastic part. When completed, your plastic part should look like the following two illustrations. While building this model, take time
Toothbrush Holder. A drawing of the sheet metal part will also be created.
Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson; Sketch (Line, Centerline, Circle, Add Relations, Smart Dimension,), Extrude Boss/Base, and Edit
Bottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
Datum Tutorial Part: Cutter
Datum Tutorial Part: Cutter Objective: Learn to apply Datums in different ways Directions 1. Datum Axis Creation a. First we need to create a center axis for the cutter b. Model Tab > Datum > Select Axis
SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI
SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered
1. Create a 2D sketch 2. Create geometry in a sketch 3. Use constraints to position geometry 4. Use dimensions to set the size of geometry
2.1: Sketching Many features that you create in Fusion 360 start with a 2D sketch. In order to create intelligent and predictable designs, a good understanding of how to create sketches and how to apply
SOLIDWORKS 2016 Basic Tools
SOLIDWORKS 2016 Basic Tools Getting Started with Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)
Engineering Technology
Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,
SDC. SolidWorks Tutorial 2001Plus. A Competency Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P.
2001Plus A Competency Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard SDC PUBLICATIONS www.schroff.com www.schroff-europe.com Project 2 Below are the desired
Getting Started. Right click on Lateral Workplane. Left Click on New Sketch
Getting Started 1. Open up PTC Pro/Desktop by either double clicking the icon or through the Start button and in Programs. 2. Once Pro/Desktop is open select File > New > Design 3. Close the Pallet window
SolidWorks Navigation
SolidWorks Basics SolidWorks Navigation Command Bar Feature Tree Model Window Simple Box Select the Front plane Create a new sketch Create a Center Rectangle from the origin Smart Dimension the length
Cube in a cube Fusion 360 tutorial
Cube in a cube Fusion 360 tutorial n Before using these instructions, it is helpful to watch this video screencast of the CAD drawing actually being done in the software. Click to link to the video tutorial.
Hydro Hull. Chapter 21. Boat. A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2).
Chapter 21 Boat Hydro Hull A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2). Step 2. Click File Menu > Save As. Step 3. Key-in HYDRO for the filename and press ENTER. B. Delete Loft1,
Introduction to 3D CAD with SolidWorks. Jianan Li
Introduction to 3D CAD with SolidWorks Jianan Li Create a New Part The first time you launch SolidWorks, it asks you to set the default units and dimension standard. Make sure you have IPS and ANSI selected,
Beginner s Guide to SolidWorks Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS
Beginner s Guide to SolidWorks 2008 Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Part Modeling
AutoDesk Inventor: Creating Working Drawings
AutoDesk Inventor: Creating Working Drawings Inventor allows you to quickly and easily make quality working drawings from your 3D models. This tutorial will walk you through the steps in creating a working
J. La Favre Fusion 360 Lesson 2 April 19, 2017
In this lesson, you will create a round plate with 12 counter-bored holes to fit 6-32 socket head screws. A counter-bored hole has two diameters, one to fit the threaded part of the screw and the other
AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.
AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and
SolidWorks 95 User s Guide
SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents
User Guide V10 SP1 Addendum
Alibre Design User Guide V10 SP1 Addendum Copyrights Information in this document is subject to change without notice. The software described in this document is furnished under a license agreement or
ME Week 2 Project 2 Flange Manifold Part
1 Project 2 - Flange Manifold Part 1.1 Instructions This project focuses on additional sketching methods and sketching commands. Revolve and Work features are also introduced. The part being modeled is
Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.
Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.
Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008
1 Introduction This lab is designed to provide you with basic skills when using the 3D modeling program SolidWorks. You will learn how to build parts, assemblies and drawings. You will be given a physical
Introduction to Sheet Metal Features SolidWorks 2009
SolidWorks 2009 Table of Contents Introduction to Sheet Metal Features Base Flange Method Magazine File.. 3 Envelopment & Development of Surfaces.. 14 Development of Transition Pieces.. 23 Conversion to
Chapter 2. Drawing Sketches for Solid Models. Learning Objectives
Chapter 2 Drawing Sketches for Solid Models Learning Objectives After completing this chapter, you will be able to: Start a new template file to draw sketches. Set up the sketching environment. Use various
Introduction to CATIA V5
Introduction to CATIA V5 Release 17 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower
Name: Date Completed: Basic Inventor Skills I
Name: Date Completed: Basic Inventor Skills I 1. Sketch, dimension and extrude a basic shape i. Select New tab from toolbar. ii. Select Standard.ipt from dialogue box by double clicking on the icon. iii.
< Then click on this icon on the vertical tool bar that pops up on the left side.
Pipe Cavity Tutorial Introduction The CADMAX Solid Master Tutorial is a great way to learn about the benefits of feature-based parametric solid modeling with CADMAX. We have assembled several typical parts
Solidworks Tutorial Pencil
The following instructions will be used to help you create a Pencil using Solidworks. These instructions are ordered to make the process as simple as possible. Deviating from the order, or not following
Getting Started. Before You Begin, make sure you customized the following settings:
Getting Started Getting Started Before getting into the detailed instructions for using Generative Drafting, the following tutorial aims at giving you a feel of what you can do with the product. It provides
Creo Parametric Primer
PTC Creo Parametric - Primer Student and Academic Editions 02 Helpful hints are enclosed in red brackets or round bubbles like this one! Creo Parametric Primer THIS VERSION OF THE CREO PRIMER HAS BEEN
Starting a 3D Modeling Part File
1 How to Create a 3D Model and Corresponding 2D Drawing with Dimensions, GDT (Geometric Dimensioning and Tolerance) Symbols and Title Block in SolidWorks 2013-2014 By Edward Locke This tutorial will introduce
SolidWorks Tutorial 1. Axis
SolidWorks Tutorial 1 Axis Axis This first exercise provides an introduction to SolidWorks software. First, we will design and draw a simple part: an axis with different diameters. You will learn how to
Shaft Hanger - SolidWorks
ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric
Create A Mug. Skills Learned. Settings Sketching 3-D Features. Revolve Offset Plane Sweep Fillet Decal* Offset Arc
Create A Mug Skills Learned Settings Sketching 3-D Features Slice Line Tool Offset Arc Revolve Offset Plane Sweep Fillet Decal* Tutorial: Creating A Custom Mug There are somethings in this world that have
ARCHICAD Introduction Tutorial
Starting a New Project ARCHICAD Introduction Tutorial 1. Double-click the Archicad Icon from the desktop 2. Click on the Grey Warning/Information box when it appears on the screen. 3. Click on the Create
Table of Contents. Lesson 1 Getting Started
NX Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard
Introduction to Autodesk Inventor for F1 in Schools (Australian Version)
Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital
Sash Clamp. Sash Clamp SW 2015 Design & Communication Graphics Page 1.
Sash Clamp 1 Introduction: The Sash clamp consists of nine parts. In creating the clamp we will be looking at the improvements made by SolidWorks in linear patterns, adding threads and in assembling the
CREO.1 MODELING A BELT WHEEL
CREO.1 MODELING A BELT WHEEL Figure 1: A belt wheel modeled in this exercise. Learning Targets In this exercise you will learn: Using symmetry when sketching Using pattern to copy features Using RMB when
Digital Camera Exercise
Commands Used New Part This lesson includes Sketching, Extruded Boss/Base, Extruded Cut, Fillet, Chamfer and Text. Click File, New on the standard toolbar. Select Part from the New SolidWorks Document
Lesson 6 2D Sketch Panel Tools
Lesson 6 2D Sketch Panel Tools Inventor s Sketch Tool Bar contains tools for creating the basic geometry to create features and parts. On the surface, the Geometry tools look fairly standard: line, circle,
Inventor-Parts-Tutorial By: Dor Ashur
Inventor-Parts-Tutorial By: Dor Ashur For Assignment: http://www.maelabs.ucsd.edu/mae3/assignments/cad/inventor_parts.pdf Open Autodesk Inventor: Start-> All Programs -> Autodesk -> Autodesk Inventor 2010
Working With Drawing Views-I
Chapter 12 Working With Drawing Views-I Learning Objectives After completing this chapter you will be able to: Generate standard three views. Generate Named Views. Generate Relative Views. Generate Predefined
Basic Features. In this lesson you will learn how to create basic CATIA features. Lesson Contents: CATIA V5 Fundamentals- Lesson 3: Basic Features
Basic Features In this lesson you will learn how to create basic CATIA features. Lesson Contents: Case Study: Basic Features Design Intent Stages in the Process Determine a Suitable Base Feature Create
Pro/E WILDFIRE, week6
Pro/E WILDFIRE, week6 1. Set working directory 2. File>New>Name is lbrack 3. When you create the part, make sure that the back surface of the vertical plate is on the front datum plane, and the lower surface
for Solidworks TRAINING GUIDE LESSON-9-CAD
for Solidworks TRAINING GUIDE LESSON-9-CAD Mastercam for SolidWorks Training Guide Objectives You will create the geometry for SolidWorks-Lesson-9 using SolidWorks 3D CAD software. You will be working
Quick Start for Autodesk Inventor
Quick Start for Autodesk Inventor Autodesk Inventor Professional is a 3D mechanical design tool with powerful solid modeling capabilities and an intuitive interface. In this lesson, you use a typical workflow
Modeling Basic Mechanical Components #1 Tie-Wrap Clip
Modeling Basic Mechanical Components #1 Tie-Wrap Clip This tutorial is about modeling simple and basic mechanical components with 3D Mechanical CAD programs, specifically one called Alibre Xpress, a freely
g. Click once on the left vertical line of the rectangle.
This drawing will require you to a model of a truck as a Solidworks Part. Please be sure to read the directions carefully before constructing the truck in Solidworks. Before submitting you will be required
Modeling an Airframe Tutorial
EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If
Diane Burton, STEM Outreach.
123D Design Tutorial: LED decoration Before using these instructions, it is very helpful to watch this video screencast of the CAD drawing actually being done in the software. Click this link for the video
Siemens NX11 tutorials. The angled part
Siemens NX11 tutorials The angled part Adaptation to NX 11 from notes from a seminar Drive-to-trial organized by IBM and GDTech. This tutorial will help you design the mechanical presented in the figure
Solid Part Four A Bracket Made by Mirroring
C h a p t e r 5 Solid Part Four A Bracket Made by Mirroring This chapter will cover the following to World Class standards: Sketch of a Solid Problem Draw a Series of Lines Finish the 2D Sketch Extrude
Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013
Level of Difficulty SketchUp An Introduction to Architectural Design Time Approximately 60 75 minutes Photocopiable/digital resources may only be copied by the purchasing institution on a single site and
Evaluation Chapter by CADArtifex
The premium provider of learning products and solutions www.cadartifex.com EVALUATION CHAPTER 2 Drawing Sketches with SOLIDWORKS In this chapter: Invoking the Part Modeling Environment Invoking the Sketching
Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013
SketchUp Level of Difficulty Time Approximately 20 25 minutes Photocopiable/digital resources may only be copied by the purchasing institution on a single site and for their own use ZigZag Education, 2013
Using Siemens NX 11 Software. The connecting rod
Using Siemens NX 11 Software The connecting rod Based on a Catia tutorial written by Loïc Stefanski. At the end of this manual, you should obtain the following part: 1 Introduction. Start NX 11 and open
Part Design Fundamentals
Part Design Fundamentals 1 Course Presentation Objectives of the course In this course you will learn basic methods to create and modify solids features and parts Targeted audience New CATIA V5 Users 1
AutoCAD 2D. Table of Contents. Lesson 1 Getting Started
AutoCAD 2D Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard
Advanced Modeling Techniques Sweep and Helical Sweep
Advanced Modeling Techniques Sweep and Helical Sweep Sweep A sweep is a profile that follows a path placed on a datum. It is important when creating a sweep that the designer plans the size of the path
Introduction to 3D Printing. Activity 1: Design a keychain using computer-aided design software
Introduction to 3D Printing Activity 1: Design a keychain using computer-aided design software 1 In this activity we ll design a keychain name tag and learn the fundamentals of computer-aided design, the
Foreword. If you have any questions about these tutorials, drop your mail to
Foreword The main objective of these tutorials is to give you a kick start using Solidworks. The approach to write this tutorial is based on what is the most important knowledge you should know and what
The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly.
Introduction - Teacher Notes Fig 1. The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly. Pro/DESKTOP enables pupils (and teachers) to communicate and model
SolidWorks Design & Technology
SolidWorks Design & Technology Training Course at PHSG Ex 5. Lego man Working with part files 8mm At first glance the Lego man looks complicated but I hope you will see that if you approach a project one
Pull Down Menu View Toolbar Design Toolbar
Pro/DESKTOP Interface The instructions in this tutorial refer to the Pro/DESKTOP interface and toolbars. The illustration below describes the main elements of the graphical interface and toolbars. Pull
To start a new drawing Select File New then from the dialog box, which appears select Normal.dft followed by OK.
Draft Tutorial This tutorial provides step-by-step instructions for the detailing of a drawing of the anchor block shown opposite. As you create this drawing, you will use the following drafting techniques:
TOY TRUCK. Figure 1. Orthographic projections of project.
TOY TRUCK Prepared by: Harry Hawkins The following project is of a small, wooden toy truck. This exercise will provide you with the procedure for constructing the various parts of the design then assembling
Autodesk Inventor. In Engineering Design & Drafting. By Edward Locke
Autodesk Inventor In Engineering Design & Drafting By Edward Locke Engineering Design Drafting Essentials Working Drawings: Orthographic Projection Views (multi-view, auxiliary view, details and sections)
Module 1H: Creating an Ellipse-Based Cylindrical Sheet-metal Lateral Piece
Inventor (10) Module 1H: 1H- 1 Module 1H: Creating an Ellipse-Based Cylindrical Sheet-metal Lateral Piece In this Module, we will learn how to create an ellipse-based cylindrical sheetmetal lateral piece
Explanation of buttons used for sketching in Unigraphics
Explanation of buttons used for sketching in Unigraphics Sketcher Tool Bar Finish Sketch is for exiting the Sketcher Task Environment. Sketch Name is the name of the current active sketch. You can also
Creo Parametric 4.0 Basic Design
Creo Parametric 4.0 Basic Design Contents Table of Contents Introduction...1 Objective of This Textbook...1 Textbook Outline...2 Textbook Conventions...3 Exercise Files...3 System Configuration...4 Notes
Below are the desired outcomes and usage competencies based on the completion of Project 4.
Engineering Design with SolidWorks Project 4 Below are the desired outcomes and usage competencies based on the completion of Project 4. Project Desired Outcomes: An understanding of the customer s requirements
Activity Sketch Plane Cube
Activity 1.5.4 Sketch Plane Cube Introduction Have you ever tried to explain to someone what you knew, and that person wanted you to tell him or her more? Here is your chance to do just that. You have
Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated)
Inventor (5) Module 2: 2-1 Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) In this tutorial, we will learn how to build a 3D model
The Revolve Feature and Assembly Modeling
The Revolve Feature and Assembly Modeling PTC Clock Page 52 PTC Contents Introduction... 54 The Revolve Feature... 55 Creating a revolved feature...57 Creating face details... 58 Using Text... 61 Assembling
Engineering Design with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P.
Engineering Design with SolidWorks 2003 A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard SDC PUBLICATIONS www.schroff.com www.schroff-europe.com
Conquering the Rubicon
Autodesk Inventor R10 Fundamentals: Conquering the Rubicon Elise Moss SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Schroff Development Corporation P.O. Box 1334
Tutorial Building the Nave Arcade
Tutorial: Digital Gothic AH C117B (Winter 2017) Tutorial Building the Nave Arcade Overview: Step 1: Determining and Drawing The Arch (Quinto Arch) Step 2: Extrude Molding Profile Step 3: Adding Walls Step
Module 2.1, 2.2 Review. EF101 Analysis & Skills Module 2.3. Sketched Features and Operations. On-line Help Two Locations
EF101 Analysis & Skills Module 2.3 Engineering Graphics Revolved Features Placed Features Work Features Module 2.1, 2.2 Review What are the three types of operations for adding features to the base feature?
Introduction to Circular Pattern Flower Pot
Prerequisite Knowledge Previous knowledge of the sketching commands Line, Circle, Add Relations, Smart Dimension is required to complete this lesson. Previous examples of Revolved Boss/Base, Cut Extrude,
When you complete this assignment you will:
Objjectiives When you complete this assignment you will: 1. create an engineering drawing file using the management file menu. 2. dimension the engineering file using the drawing annotation menu. 3. produce
Student + Instructor:
BLUE boxed notes are intended as aids to the lecturer RED boxed notes are comments that the lecturer could make Show 01 Solid Modeling Intro slides quickly. SolidWorks Layout slides are on EEIC for reference
Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge
Inventor (10) Module 1G: 1G- 1 Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge In Module 1A, we have explored
2809 CAD TRAINING: Part 1 Sketching and Making 3D Parts. Contents
Contents Getting Started... 2 Lesson 1:... 3 Lesson 2:... 13 Lesson 3:... 19 Lesson 4:... 23 Lesson 5:... 25 Final Project:... 28 Getting Started Get Autodesk Inventor Go to http://students.autodesk.com/
FUSION 360: SKETCHING FOR MAKERS
FUSION 360: SKETCHING FOR MAKERS LaDeana Dockery 2017 MAKEICT Wichita, KS 1 Table of Contents Interface... 1 File Operations... 1 Opening Existing Models... 1 Mouse Navigation... 1 Preferences... 2 Navigation
1.6.7 Add Arc Length Dimension Modify Dimension Value Check the Sketch Curve Connectivity
Contents 2D Sketch... 1 1.1 2D Sketch Introduction... 1 1.1.1 2D Sketch... 1 1.1.2 Basic Setting of 2D Sketch... 2 1.1.3 Exit 2D Sketch... 4 1.2 Draw Common Geometry... 5 2.2.1 Points... 5 2.2.2 Lines
MAKING THE FAN HOUSING
Our goal is to make the following part: 39-245 RAPID PROTOTYPE DESIGN CARNEGIE MELLON UNIVERSITY SPRING 2007 MAKING THE FAN HOUSING This part is made up of two plates joined by a cylinder with holes in
Wireless Mouse Surfaces
Wireless Mouse Surfaces Design & Communication Graphics Table of Contents Table of Contents... 1 Introduction 2 Mouse Body. 3 Edge Cut.12 Centre Cut....14 Wheel Opening.. 15 Wheel Location.. 16 Laser..
WEEK 5: Shaft Modeling (C51X01, C51X02) Revolved Features, Chamfer
WEEK 5: Shaft Modeling (C51X01, C51X02) Revolved Features, Chamfer 1. Creating the Shaft Model 1. File> New> Part, Name: C51X01> OK 2. Insert> Revolve> Placement> Define> select TOP datum plane> Sketch
Anchor Block Draft Tutorial
Anchor Block Draft Tutorial In the following tutorial you will create a drawing of the anchor block shown. The tutorial covers such topics as creating: Orthographic views Section views Auxiliary views
Assembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B:
MECH 130 CAD LAB 5 SPRING 2017 due Friday, April 21, 2016 at 4:30 PM All of LAB 5 s hardcopies will be working drawing layouts. Do not print out from the part file. We will be using the ME130DRAW drawing
Custom Pillow Block Design Protrusion, Cut, Round, Draft (Review) Drawing (Review) Inheritance Feature (New) Creo 2.0
Custom Pillow Block Design Protrusion, Cut, Round, Draft (Review) Drawing (Review) Inheritance Feature (New) Creo 2.0 Rotatable pdf files: Casting Machining Grease Fitting Boss The general design of the
with Creo Parametric 4.0
Parametric Modeling with Creo Parametric 4.0 An Introduction to Creo Parametric 4.0 NEW Contains a new chapter on 3D Printing Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com