Drawing Types & Construction Drawings
|
|
- Clyde Park
- 5 years ago
- Views:
Transcription
1 Drawing Types & Construction Drawings
2 Building projects require several types of specialised drawings. This collection of drawings, known as a project set, includes: Location Plan Site Plan Floor Plan Elevation Sectional Views Rendered Illustrations Buildings are designed by architects along with various other members if a design team. The team ensures the building meets the needs of the client and satisfies local authority planning department and building control regulations.
3 Location Plan A Location plan shows where the site is located within the local area. It shows: Roads Outlines of buildings Site boundaries North Sign Land contour lines
4 A site plan shows the building within their site/boundary. The buildings are Shown as outlines and the boundaries marked slightly darker. It shows: Plot Number Waste pipe runs Manholes Trees Contour lines Position of building Site Plan
5 Floor Plan A floor plan shows the layout of the room inside the building and the position Of the doors, windows and other important objects. Architects often use several layers to show different types of fixtures and Fittings Such as plumbing, electric wiring etc. Scale 1:50
6 Elevation Used to show the outside features of a building, including position of the door, Windows etc.
7 Sectional Drawing
8 First Angle Projection First angle projection is a method of creating a 2D drawing of a 3D object. Note the symbol for first angle orthographic projection. This is important information for the person interpreting the drawing because if you examine the diagram below you will note that in first angle orthographic projection: the view from the front is in the middle the view from the left is on the right the view from the right is on the left the view from the top is on the bottom the view from the bottom is on the top the view from the rear is on the far right. Third Angle Projection Third angle projection is a method of creating a 2D drawing of a 3D object. Note the symbol for third angle projection. This is important information for the person interpreting the drawing because in third angle projection: the view from the front is in the middle the view from the left is on the left the view from the right is on the right the view from the top is on the top the view from the bottom is on the bottom the view from the rear is on the far right
9 Orthographic Drawings In engineering, a technique called orthographic projection is used to show a three dimensional object as a two dimensional drawing. Orthographic projection allows all possible views of a three dimensional object to be shown in a two dimensional drawing. It uses multiple views of the object, taken from points of view rotated about the object's centre through increments of 90. Isometric Drawings Isometric drawings are 3D drawings. They show three sides, all in dimensional proportion, but none are shown as a true shape with 90 degree corners. All the vertical lines are drawn vertically All horizontal lines are drawn at 30 degrees to the base line. Isometric is an easy and realistic method of drawing 3D images.
10 Oblique Drawings Oblique drawings are also used in engineering. The object is drawn with the most distinguishing features facing directly towards the observer, showing the true shape of these features. To show the 3D effect, parallel lines (called ' lines of sight') are drawn from the front face at an angle of 45 degrees. Distances are halved on the 45 degree line. Circular features like round holes can be drawn on this front face as true circles. Planometric Drawings The difference is that instead of the front view being a true view as in OBLIQUE; the PLAN view is the true view in PLANOMETRIC. However the plan view is drawn at 45 or 30 /60. The angle between the lines is always 90. The front and side views are projected upwards from the plan. Planometric is very popular with architects when a plan is often the most important view.
11 Perspective Drawings Perspective drawings show objects as you would see them in the real world - in three dimensional view. The lines of sight in a perspective drawing can be projected to a vanishing point in the distance. This is what gives the appearance of depth. Perspective drawings are a 3D representation of an object but the proportions are not true they are distorted to give the perception of depth. Also the detail at the farthest ends can be difficult to see because it is so small. Sectional Drawings Section or cross section drawings show a product as if it has been sliced in half. The imaginary cut is called a section plane which is sometimes represented by a line consisting of long and short dashes. Parts of the object that are cut through are shaded by cross-hatching. If two parts touch, then the cross-hatching goes in opposite direction. Parts such as nuts and bolts, studs, screws, shafts, gear teeth, roller bearings, ball bearings, webs and axles are not sectioned.
12 Assembly Drawings An assembly drawing shows how parts of a product fit together. They are often used to show how to assemble parts of model kits and flat-pack furniture. There are two types: A fitted assembly drawing shows the parts put together. An exploded drawing shows the parts separated, but in the correct relationship for fitting together. Hidden Detail on Drawings Many objects have internal features, such as holes, slots and grooves. These features cannot be seen when viewed side on in real life, but can be represented as hidden outlines (ie dashed lines) in drawings. Parts of an object may also conceal other parts and so the hidden parts may be shown on a drawing as hidden outlines.
Orthographic Projection
Orthographic Projection Why Orthographic Projection is used in technical drawing Orthographic projection is a method of producing a number of separate two-dimensional inter-related views, which are mutually
More informationORTHOGRAPHIC PROJECTIONS. Ms. Sicola
ORTHOGRAPHIC PROJECTIONS Ms. Sicola Objectives List the six principal views of projection Sketch the top, front and right-side views of an object with normal, inclined, and oblique surfaces Objectives
More informationPage 1 of 5. ENGINEERING SKETCHES INFORMATION SHEETS MEL02INF2430 v1.1 HEALTH & SAFETY REQUIREMENTS
Page 1 of 5 Competenz - N Z Engineering Food & Manufacturing Industry Training Organisation Inc. ENGINEERING SKETCHES INFORMATION SHEETS MEL02INF2430 v1.1 HEALTH & SAFETY REQUIREMENTS RECORDING REQUIREMENTS:
More informationInterpretation of Drawings. An Introduction to the Basic Concepts of Creating Technical Drawings
Interpretation of Drawings An Introduction to the Basic Concepts of Creating Technical Drawings Introduction In the design process drawings are the main way in which information about an object or product
More informationENGINEERING GRAPHICS 1.0 Introduction Engineering Graphics Drawing as an art Artist Graphic design Engineering graphics engineering drawing
ENGINEERING GRAPHICS 1.0 Introduction Engineering is the profession in which the knowledge of mathematics and science gained by study, experience and practice is applied with good judgment to develop a
More informationAdd labels to the sides...
Orthographic Drawings Orthographic Projection A projection on a plane, using lines perpendicular to the plane Graphic communications has many forms. Orthographics is one such form. It was developed as
More informationFACTFILE: GCE TECHNOLOGY & DESIGN
FACTFILE: GCE TECHNOLOGY & DESIGN 1.8, 1.26, 1.56 DESIGN AND COMMUNICATION Design and Communication Learning outcomes Students should be able to: communicate designs using 2D methods, to include freehand
More information2018 Technical Drawing Specifications Resource A guide to support VCE Visual Communication Design Study Design
2018 Technical Drawing Specifications Resource A guide to support VCE Visual Communication Design Study Design 2018 22 VICTORIAN CURRICULUM AND ASSESSMENT AUTHORITY 1 Contents A guide to support VCE Visual
More informationTechnological Design Mr. Wadowski. Orthographic & Isometric Drawing Lesson
Technological Design Mr. Wadowski Orthographic & Isometric Drawing Lesson TOPICS Working Drawings, Isometric Drawings & Orthographic Drawings Glass box concept Multiview projection Orthographic projection
More information1 ISOMETRIC PROJECTION SECTION I: INTRODUCTION TO ISOMETRIC PROJECTION
1 ISOMETRIC PROJECTION SECTION I: INTRODUCTION TO ISOMETRIC PROJECTION Orthographic projection shows drawings of an object in a two-dimensional format, with views given in plan, elevation and end elevation
More informationENGINEERING GRAPHICS ESSENTIALS
ENGINEERING GRAPHICS ESSENTIALS Text and Digital Learning KIRSTIE PLANTENBERG FIFTH EDITION SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com ACCESS CODE UNIQUE CODE INSIDE
More informationGuide To British Standards
Guide To British Standards Higher Graphic Communication C O N T E N T S page TITLE BLOCK 2 DRAWING SCALES 2 LINE TYPES 3 ORTHOGRAPHIC PROJECTION 4 SECTIONAL VIEWS 4 SCREW THREADS & COMPONENTS 7 INTERUPTTED
More informationEngineering Graphics Essentials with AutoCAD 2015 Instruction
Kirstie Plantenberg Engineering Graphics Essentials with AutoCAD 2015 Instruction Text and Video Instruction Multimedia Disc SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com
More informationENGINEERING GRAPHICS ESSENTIALS
ENGINEERING GRAPHICS ESSENTIALS with AutoCAD 2012 Instruction Introduction to AutoCAD Engineering Graphics Principles Hand Sketching Text and Independent Learning CD Independent Learning CD: A Comprehensive
More informationORTHOGRAPHIC PROJECTION
ORTHOGRAPHIC PROJECTION C H A P T E R S I X OBJECTIVES 1. Recognize and the symbol for third-angle projection. 2. List the six principal views of projection. 3. Understand which views show depth in a drawing
More informationLeaving Certificate Technology
Leaving Certificate Technology Core Module Resource: Communications and Graphics Media Communications and Graphics Media Resource Document Material and Layout Range of tasks exploring topics and learning
More informationProduct design: Communicating your design proposals
Product design: Communicating your design proposals In the world of business and industry design proposals can only be turned into saleable products if the designers communicate their proposals effectively.
More informationC A R I B B E A N E X A M I N A T I O N S C O U N C I L REPORT ON CANDIDATES WORK IN THE SECONDARY EDUCATION CERTIFICATE EXAMINATION MAY/JUNE 2010
C A R I B B E A N E X A M I N A T I O N S C O U N C I L REPORT ON CANDIDATES WORK IN THE SECONDARY EDUCATION CERTIFICATE EXAMINATION MAY/JUNE 2010 TECHNICAL DRAWING GENERAL PROFICIENCY Copyright 2010 Caribbean
More informationPerspective Notes 8 th Grade Art
Perspective Notes 8 th Grade Art Perspective Perspective is the representation of three-dimensional objects on a flat twodimensional surface. In perspective drawing, objects are made to recede in space
More informationEngineering Drawing Lecture 5 PROJECTION THEORY
University of Palestine College of Engineering & Urban Planning First Level Engineering Drawing Lecture 5 PROJECTION THEORY Lecturer: Eng. Eman Al.Swaity Eng.Heba hamad PART 1 PROJECTION METHOD TOPICS
More informationCopyrighted Material. Copyrighted Material. Copyrighted. Copyrighted. Material
Engineering Graphics ORTHOGRAPHIC PROJECTION People who work with drawings develop the ability to look at lines on paper or on a computer screen and "see" the shapes of the objects the lines represent.
More informationExtension material for Level 2 Design and Visual Communication Study Guide
3-D formal drawing Extension material for Level 2 Design and Visual Communication Study Guide ISBN 978-1-927194-15-7 For individual student use only. No other use permitted. ESA Publications (NZ) Ltd,
More informationSketching Fundamentals
Sketching Fundamentals Learning Outcome When you complete this module you will be able to: Make basic engineering sketches of plant equipment. Learning Objectives Here is what you will be able to do when
More informationStudent Name: Teacher: Date: District: Rowan. Assessment: 9_12 T and I IC61 - Drafting I Test 1. Description: Unit C - Sketching - Test 2.
Student Name: Teacher: Date: District: Rowan Assessment: 9_12 T and I IC61 - Drafting I Test 1 Description: Unit C - Sketching - Test 2 Form: 501 1. The most often used combination of views includes the:
More information11/12/2015 CHAPTER 7. Axonometric Drawings (cont.) Axonometric Drawings (cont.) Isometric Projections (cont.) 1) Axonometric Drawings
CHAPTER 7 1) Axonometric Drawings 1) Introduction Isometric & Oblique Projection Axonometric projection is a parallel projection technique used to create a pictorial drawing of an object by rotating the
More informationContinuous thick. Continuous thin. Continuous thin straight with zigzags. Dashed thin line. Chain thin. Chain thin double dash
Types of line used Continuous thick Used for visible outlines and edges. Continuous thin Used for projection, dimensioning, leader lines, hatching and short centre lines. Continuous thin straight with
More informationAt the conclusion of this unit you should be able to accomplish the following with a 70% accuracy
7 Multiview Drawing OBJECTIVES At the conclusion of this unit you should be able to accomplish the following with a 70% accuracy 1. explain the importance of mulitview drawing as a communication tool far
More informationMultiviews and Auxiliary Views
Multiviews and Auxiliary Views Multiviews and Auxiliary Views Objectives Explain orthographic and multiview projection. Identifying the six principal views. Apply standard line practices to multiviews
More informationPerspective Sketching
Perspective Sketching Perspective Drawings A perspective drawing offers the most realistic three-dimensional view of all the pictorial methods, because it portrays the object in a manner that is most similar
More informationDrawing Standards & Conventions for IDD
Drawing Standards & Conventions for IDD This document consists of a set of standards that have been developed to maintain a consistency in Interior Decoration and Design students work. The standards are
More informationCDT: DESIGN AND COMMUNICATION
CDT: DESIGN AND COMMUNICATION Paper 7048/01 Structured Key message Whilst many excellent answers were seen, the following were considered to be areas where improvement could be made: the correct positioning
More informationMulti-View Drawing Review
Multi-View Drawing Review Sacramento City College EDT 300/ENGR 306 EDT 300 / ENGR 306 - Chapter 5 1 Objectives Identify and select the various views of an object. Determine the number of views needed to
More informationENGINEERING GRAPHICS
ENGINEERING GRAPHICS Time allowed : 3 hours Maximum Marks : 70 Note : (ii) Attempt all the questions. Use both sides of the drawing sheet, if necessary. (iii) All dimensions are in millimetres. (iv) Missing
More informationDMT113 Engineering Drawing. Chapter 3 Stretch System
DMT113 Engineering Drawing Chapter 3 Stretch System Contents Theory & Multiview Planes 6 Principle Views Multiview Sketching Technique & Perspective First & Third Angle Multiview Representations Theory
More informationMarking Scheme Engineering Graphics
Marking Scheme Engineering Graphics All Questions are to be answered correctly and accurately. General Note: (i) (ii) (iii) (iv) (v) Marks are to be awarded in proportion to the work done. Mistakes in
More informationOrthographic Drawing (Architectural Board Drafting)
Design and Drafting Description In this activity, the teacher will introduce orthographic projection, in which a multi-view drawing shows how the sides of an object are related to each another. Students
More informationPROJECTIONS PARALLEL CONICAL PROJECTIONS PROJECTIONS OBLIQUE ORTHOGRAPHIC PROJECTIONS PROJECTIONS
PROJECTIONS CONICAL PROJECTIONS PARALLEL PROJECTIONS OBLIQUE PROJECTIONS ORTHOGRAPHIC PROJECTIONS ISOMETRIC MULTI-VIEW an object; The Description of Forms Behind every drawing of an object is space relationship
More informationENGR 1182 Exam 1 First Mid Term Exam Study Guide and Practice Problems
Spring Semester 2016 ENGR 1182 Exam 1 First Mid Term Exam Study Guide and Practice Problems Disclaimer Problems in this study guide resemble problems relating mainly to the pertinent homework assignments.
More informationEngineering Working Drawings Basics
Engineering Working Drawings Basics Engineering graphics is an effective way of communicating technical ideas and it is an essential tool in engineering design where most of the design process is graphically
More informationMultiview Drawing. Definition: Graphical representation of a 3- dimensional object on one plane (sheet of paper) using two or more views.
Multiview Drawing Definition: Graphical representation of a 3- dimensional object on one plane (sheet of paper) using two or more views. Multiview Drawing Another name for multiview drawing is orthographic
More informationOrthographic Projection 1
Orthographic Projection 1 What Is Orthographic Projection? Basically it is a way a representing a 3D object on a piece of paper. This means we make the object becomes 2D. The difference between Orthographic
More informationME1105 Engineering Drawing & Design
City University London Term 1 Assessment 2008/2009 School of Engineering and Mathematical Sciences ME1105 Engineering Drawing & Design Student Name:.., Group: Examination duration: Reading time: This paper
More informationEngineering Graphics. Class 2 Drafting Instruments Mohammad Kilani
Engineering Graphics Class 2 Drafting Instruments Mohammad Kilani Drafting Instruments A Design is as good as its instruments A engineering drawing is a highly stylized graphic representation of an idea.
More informationLESSON 1: UNDERSTANDING CONSTRUCTION DRAWINGS
LESSON 1: UNDERSTANDING CONSTRUCTION DRAWINGS INTRODUCTION In this lesson, you ll learn about the different types of drawings used in the construction industry, and how to read floor plans, section drawings,
More informationDevelop an Interior perspective from a floor plan using 2 points. using orthographic projection techniques
Develop an Interior perspective from a floor plan using 2 points using orthographic projection techniques Obtain a floor of the space to be drawn Digital or hand drawn plan Plan must be to scale Often
More informationCLASS views from detail on a grid paper. (use appropriate line types to show features) - Optional views. Turn in for grading on class 6 (06/04)
CLASS 4 Review: - Projections - Orthographic projections Lab: - 3 views from detail on a grid paper. (use appropriate line types to show features) - Optional views. Turn in for grading on class 6 (06/04)
More informationEnvironmental Design. Floor Plan. Planometric Drawing. Target Audience. Media. Materials
Environmental Design The design of large-scale aspects of the environment by means of architecture, interior design, way-finding, landscape architecture, etc. Floor Plan A scale diagram of the arrangement
More informationHigher Graphic Communication. Homework. Knowledge and Interpretation. Name. Page
Higher Graphic Communication Homework Knowledge and Interpretation Name Page Homework 1 Q1. For each of the following lines name each and explain where it would be used on a drawing. A coloured electronic
More informationMULTIPLE CHOICE QUESTIONS - CHAPTER 6
MULTIPLE CHOICE QUESTIONS - CHAPTER 6 1. The selection of the front view in executing a multiview drawing of an object is dependent upon the following factors: a. size and shape of the object and their
More informationIsometric Drawing Chapter 26
Isometric Drawing Chapter 26 Sacramento City College EDT 310 EDT 310 - Chapter 26 - Isometric Drawing 1 Drawing Types Pictorial Drawing types: Perspective Orthographic Isometric Oblique Pictorial - like
More informationDownloaded from ENGINEERING DRAWING. Time allowed : 3 hours Maximum Marks : 70
ENGINEERING DRAWING Time allowed : 3 hours Maximum Marks : 70 Note : (i) (ii) Attempt all the questions. Use both sides of the drawing sheet, if necessary. (iii) All dimensions are in millimeters. (iv)
More informationLecture #4 MULTIVIEW PROJECTION RES 112E COMPUTER AIDED TECHNICAL DRAWING ITU
Lecture #4 MULTIVIEW PROJECTION This week You will learn multi-view projection. The steps to follow are: Projections (ISO-E & ISO-A) Multi-view drawings Views (Basic,Auxiliary, Detailed etc.) Sketching
More informationHeavy-Duty Bypass Track System
Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,
More informationZIMBABWE SCHOOL EXAMINATIONS COUNCIL (ZIMSEC)
ZIMBABWE SCHOOL EXAMINATIONS COUNCIL (ZIMSEC) ADVANCED LEVEL SYLLABUS For 2013-2016 Geometrical & Mechanical/ Building Drawing 9196 1.0 PREAMBLE/INTRODUCTION This syllabus provides a two year course in
More informationContents. Foreword. Using this Guide
Foreword xv Preface xvii Scope Using this Guide xix xix 1 Specifying technical products 1 1.1 What is meant by technical product specification? 1 1.2 Design brief 1 1.3 Function 1 1.4 Specifications 2
More informationContents. Notes on the use of this publication
Contents Preface xxiii Scope Notes on the use of this publication xxv xxvi 1 Layout of drawings 1 1.1 General 1 1.2 Drawing sheets 1 1.3 Title block 2 1.4 Borders and frames 2 1.5 Drawing formats 2 1.6
More information*X033/12/01* X033/12/01 HIGHER STAPLE HERE NATIONAL QUALIFICATIONS. 8 Orthographic drawings are in third angle projection.
Question 2 3 4 Section A Total 7a 7b 8 9 0 EITHER OR 2 Section B Total Total Marks A + B Marks STAPLE HERE FOR OFFICIAL USE 033/2/0 NATIONAL QUALIFICATIONS 204 THURSDAY, 8 MAY.00 PM 4.00 PM GRAPHIC COMMUNICATION
More informationUNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS
UNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS 5.1 Introduction Orthographic views are 2D images of a 3D object obtained by viewing it from different orthogonal directions. Six principal views are possible
More informationEngineering Graphics, Class 8 Orthographic Projection. Mohammad I. Kilani. Mechanical Engineering Department University of Jordan
Engineering Graphics, Class 8 Orthographic Projection Mohammad I. Kilani Mechanical Engineering Department University of Jordan Multi view drawings Multi view drawings provide accurate shape descriptions
More informationChapter 5 Pictorial sketching
Chapter 5 Pictorial sketching Contents Freehand sketching techniques Pictorial projections - Axonometric - Oblique Isometric projection vs isometric sketch Isometric sketch from an orthographic views Isometric
More informationFundamentals for building Drawing
Fundamentals for building Drawing What is Drawing Introduction Knowledge of preparing and understanding drawing will prove to be an invaluable aid while performing their jobs effectively, efficiently.
More informationBeginning Engineering Graphics 3 rd Week Lecture Notes Instructor: Edward N. Locke Topic: The Coordinate System, Types of Drawings and Orthographic
Beginning Engineering Graphics 3 rd Week Lecture Notes Instructor: Edward N. Locke Topic: The Coordinate System, Types of Drawings and Orthographic 1 st Subject: The Cartesian Coordinate System The Cartesian
More information3D PRINTER. Pack 11. Anything you can imagine, you can make! 3D technology is now available for you at home! BUILD YOUR OWN
BUILD YOUR OWN Pack 11 Anything you can imagine, you can make! 3D PRINTER Compatible with Windows 7 & 8 Mac OS X 3D technology is now available for you at home! BUILD YOUR OWN 3D PRINTER CONTENTS PACK
More informationENGINEERING DRAWING IM 09 AND GRAPHICAL COMMUNICATION
IM SYLLABUS (2014) ENGINEERING DRAWING IM 09 AND GRAPHICAL COMMUNICATION SYLLABUS Engineering Drawing and Graphical Communication IM 09 (Available in September) Syllabus 1 Paper (3 hours) Aims The aims
More informationDFTG-1305 Technical Drafting Prof. Francis Ha
DFTG-1305 Technical Drafting Prof. Francis Ha Session 4 Orthographic Projection (or Multiview Projection) Reading: Geisecke s textbook: 14 th Ed. Chapter 5 p.162 15 th Ed. Chapter 6 p.232 Update: 18-0205
More informationFundamentals of Drafting - Orthographic Projection with Hidden Details
Fundamentals of Drafting - Orthographic Projection with Hidden Details Objectives: 1. To extend the principle of orthographic projection for hidden details. 2. To illustrate the representation of hidden
More informationSketching in SciTech. What you need to know for graphic communication
Sketching in SciTech What you need to know for graphic communication Sketching in your Logbook Use pencil Take up the WHOLE PAGE Label things 1. Proportion Each part of the sketch is the right size,
More informationSection 5. Graphic techniques for portfolio presentation
Graphics techniques 117 Section 5 Graphic techniques for portfolio presentation A general knowledge of some basic graphic techniques is needed by all Technology students in order that the presentation
More informationENGINEERING AND DESIGN
ENGINEERING AND DESIGN EXAMINATION GUIDELINES GRADE 12 2017 These guidelines consist of 10 pages. Engineering Graphics and Design 2 DBE/2017 TABLE OF CONTENTS Page 1. INTRODUCTION 3 2. ASSESSMENT IN GRADE
More informationGRAPHIC COMMUNICATION
GRAPHIC COMMUNICATION TECHNICAL GRAPHICS INFORMATION SHEETS Sectional Drawing Auxiliary Drawing Location Drawing Dimensional Tolerance Types of Graphic Communication ORTHOGRAHIC PROJECTION SECTIONAL VIEWS
More informationTechnology Education Grades Drafting I
Technology Education Grades 9-12 Drafting I 46 Grade Level: 9, 10, 11, 12 Technology Education, Grades 9-12 Drafting I Prerequisite: None Drafting I is an elective course which provides students the opportunity
More informationStudy: Visual Communication & Design
CATHOLIC REGIONAL COLLEGE SYDENHAM Rationale: Study: Visual Communication & Design Visual Communication is a bridge between an idea and its intended audience. In the fields of architecture, engineering,
More informationHorizon - The horizontal line that contains the vanishing point(s) in a perspective drawing.
Representing Solids Perspective Drawing A drawing where non-vertical parallel lines appear to meet at a point called a vanishing point. Example: If you look straight down a highway, it appears that the
More informationENGINEERING GRAPHICS
ENGINEERING GRAPHICS CLASS - XII (046) DESIGN OF THE QUESTION PAPER Time : 3 Hrs Max. Marks : 70 The weightage of the distribution of marks over different contents of the question paper shall be as follows:
More informationMultiview Projection
DFTG-1305 Technical Drafting Prof. Francis Ha Session 4 Multiview Projection (or Orthographic Projection) Reading: Geisecke s textbook: 14 th Ed. Chapter 5 p.162 15 th Ed. Chapter 6 p.232 Update: 17-0510
More informationAircraft Drawing and Blueprint Reading
Aircraft Drawing and Blueprint Reading Course Introduction Types of drawings Engineering also known as production or working drawings. Block diagram Types of Drawings Schematics Sketches Charts and graphs
More informationHD installation guide
JANUS INTERNATIONAL 1 866 562 2580 www.janusintl.c o m 1950 1950HD installation guide RIGHT DRIVE END SHOWN LH OPPOSITE LEFT TENSION END SHOWN RH OPPOSITE PUSH-UP OPERATION 1950 1950HD SHOWN A rolling
More informationObtained from Omarshauntedtrail.com
DaveintheGrave's Halloween Props Animated Crawling Skeleton Build a life-size skeleton torso that realistically crawls across the lawn one arm at a time. 1. Motor Base and Linkage Assembly BASE - I used
More informationPerspective. Basic Perspective For Drawing
Perspective Basic Perspective For Drawing Perspective is one of the most important tools in drawing a 3-dimensional scene or object on a 2-dimensional surface. Types of Linear perspective: Single- (or
More informationBlueprint Reading Basics For Welding Fabrication
Blueprint Reading Basics For Welding Fabrication 9/14/2011 1 Definitions of Lines Lines are the basic communication tool used in blueprints. Listed below are examples of the most common lines used in blueprints
More informationENGINEERING COMMUNICATIONS. Student Number:.
The University of Melbourne Semester 2 Assessment, 1999 Department of Mechanical and Manufacturing Engineering 436-105 ENGINEERING COMMUNICATIONS Student Number:. Examination duration: Reading time: This
More informationItem #28187 EASTWOOD BEAD ROLLER INSTRUCTIONS
Item #28187 EASTWOOD BEAD ROLLER INSTRUCTIONS The Eastwood Bead Roller is a professional metal fabrication tool for producing strengthening ribs in panels used in creating replacement fl oor pans, fi rewalls,
More informationDWG 002. Blueprint Reading. Geometric Terminology Orthographic Projection. Instructor Guide
DWG 002 Blueprint Reading Geometric Terminology Orthographic Projection Instructor Guide Introduction Module Purpose The purpose of the Blueprint Reading modules is to introduce students to production
More informationTRIAL EXAMINATION 2012
ENGINEERING GRAPHICS AND DESIGN - TRIAL PAPER TWO - 0 education Department: Education KwaZulu - Natal GRADE ENGINEERING GRAPHICS AND DESIGN P TRIAL EXAMINATION 0 S : 00 TIME : HOURS This question paper
More informationProduction drawing Diagram. a) I am a freehand drawing that follows technical drawing standards.
THE TECHNOLOGICAL WORLD Graphical language STUDENT BOOK Ch. 11, pp. 336 342 Basic lines, geometric lines, sketches 1. In technology, the two most widely used types of technical drawings are: a) sketch
More informationChapter 1 Overview of an Engineering Drawing
Chapter 1 Overview of an Engineering Drawing TOPICS Graphics language Engineering drawing Projection methods Orthographic projection Drawing standards TOPICS Traditional Drawing Tools Lettering Freehand
More informationEntry Level Assessment Blueprint Architectural Drafting
Entry Level Assessment Blueprint Architectural Drafting Test Code: 4004 / Version: 01 Specific Competencies and Skills Tested in this Assessment: Preparing to Draw Identify drafting tools, materials, and
More informationSDC PUBLICATIONS. Schroff Development Corporation
SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com SECTIONING In chapter 3 you will learn how to create various types of sectional views. Sectional views allow you
More informationClassical Viewing. Ed Angel Professor of Computer Science, Electrical and Computer Engineering, and Media Arts University of New Mexico
Classical Viewing Ed Angel Professor of Computer Science, Electrical and Computer Engineering, and Media Arts University of New Mexico 1 Objectives Introduce the classical views Compare and contrast image
More informationCOPYRIGHTED MATERIAL. Contours and Form DEFINITION
1 DEFINITION A clear understanding of what a contour represents is fundamental to the grading process. Technically defined, a contour is an imaginary line that connects all points of equal elevation above
More informationRevised
Indentify Non-powered panels and separate from Powered panels. Non-powered panel shown at left.. Powered panel shown at left has powerway mounted at factory. Also separate panels by surface type, width
More informationLECTURE 1 INRTRODUCTION TO CIVIL ENGINEERING DRAWING. Engr. Ali Raza Khalid Civil Engineering drawing
LECTURE 1 INRTRODUCTION TO CIVIL ENGINEERING DRAWING Engr. Ali Raza Khalid CIVIL ENGINEERING DRAWING COURSE OUTLINE Credit Hours: 2+2= 4 Introduction: Introduction to the subject and drawing equipment.
More information1. When sketching long, narrow objects in OBLIQUE, distortion can be lessened by placing the long dimension along:
Draft Student Name: Teacher: District: Date: Wake County Test: 9_12 T and I IC61 - Drafting I Test 2 Description: 3.03 Apply 3D sketching Form: 501 1. When sketching long, narrow objects in OBLIQUE, distortion
More informationDimensioning. Dimensions: Are required on detail drawings. Provide the shape, size and location description: ASME Dimensioning Standards
Dimensioning Dimensions: Are required on detail drawings. Provide the shape, size and location description: - Size dimensions - Location dimensions - Notes Local notes (specific notes) General notes ASME
More informationtechnical drawing
technical drawing school of art, design and architecture nust spring 2011 http://www.youtube.com/watch?v=q6mk9hpxwvo http://www.youtube.com/watch?v=bnu2gb7w4qs Objective abstraction - axonometric view
More informationProduct Modelling in Solid Works
Product Modelling in Solid Works In the following exercise you will use solid works to construct the computer mouse shown opposite. In this exercise you will use a number of advanced features to achieve
More informationProjections. Conceptual Model of the 3D viewing process
Projections Projections Conceptual Model of the 3D viewing process 3D Projections (Rays converge on eye position) (Rays parallel to view plane) Perspective Parallel Orthographic Oblique Elevations Axonometric
More informationGlass Box Projection. Gives you 6 sides to view of an object. 10/2/14 2
2D Drawings Glass Box Projection Gives you 6 sides to view of an object. 10/2/14 2 We can simplify this for some objects to 3 views Glass Box Approach Glass Box Approach Glass Box Approach Glass Box Approach
More informationWINTER 15 EXAMINATIONS Subject Code: Model Answer- Building Drawing Page No- 01 /15
Subject Code: 17309 Model Answer- Building Drawing Page No- 01 /15 Important Instruction to Examiners:- 1) The answers should be examined by key words & not as word to word as given in the model answers
More informationKitchen and Bath Design Tutorial
Kitchen and Bath Design Tutorial This tutorial continues where the Interior Design Tutorial left off. You should save this tutorial using a new name to archive your previous work. The tools and techniques
More information