Record As-Built Drawings for Capital Projects

Size: px
Start display at page:

Download "Record As-Built Drawings for Capital Projects"

Transcription

1 Section 19.1 Record As-Built Drawings for Capital Projects Overview - Section 19.1 Internal Use: Full compliance where applicable Contractor Use: Full compliance where applicable The intention of this section is to streamline the Workflows and As-Built process within Design Drafting, by documenting CAD related steps and review the As-Built Record Form that tracks each project. All steps comply with Denver Water s CAD Standards and shall be followed as closely as possible, with the understanding that every project is unique and may require special circumstances. Many of the processes listed in this document are not exclusive to the As-Built process and can be utilized on other projects. Supporting documents Throughout this document several other documents will be referenced, and can be found in the following Dashboard locations: Engineering Project Procedures Capital Projects Procedures Manual (CPPM) Workflows As-Built workflow As-Built to ARG workflow Project Management/Design Drafting As-Built Record Form ARG Minimum Requirements List (for Legacy Projects) Asset Recording Group Domain List Pipe Rules Survey Grid Coverages Section Record As-Built Drawings for Capital Projects

2 As-Built Record Form The As-Built Record Form is a new document procedure to help track where any project is at any given time. The form is based off lessons learned from issues with closing out As-Built records. This form will remain as a physical copy and is to be maintained by the As-Built Supervisor until the project has been completed and then scanned to the respective Project folder. Add Project Name here Add Project Tracker Number here Step 1: The As-Built Supervisor will meet with the Asset Recording Group to determine whether the project will need to be posted to E-Map: ARG Representative to fill out reasons why project will or will not be posted to E-Map. Sign and Date Check the answer Step 2: Some projects already have GPS Points associated with them. Typically the GPS points will be located in the GPS folder within Dsgn or Srvy. If there is not GPS associated with the project then a request can be sent to Survey. Check each applicable answer Standard: any GPS point collected to the current standard - where the values will translate directly into the ARG Attributes Non-Standard: any GPS point not collected to the current standard - values will not translate directly into the ARG Attributes. Minimal information, and used primarily for location only Section Record As-Built Drawings for Capital Projects

3 Step 3: This section is to be filled out each time the physical plans exchange hands between the Engineers and Drafters: See the Engineering SharePoint Site Project Management/Design Drafting to find the most up-to-date As- Built Record Form. Section Record As-Built Drawings for Capital Projects

4 Record Drawing Projects Overview Record Drawing refers to any project designed using the current CAD Standard. Since these projects were completed with the new way of thinking Non-Legacy projects have their own workflow and file management system. As stated previously, Legacy refers to any project designed before the 2011 CAD Standards. Since these projects were completed with an old way of thinking Legacy projects have their own workflow and file management system. Workflow See the Engineering SharePoint site Capital Projects Procedures Manual to find the most up-to-date Workflows: File Management The drawings (.dwg) and Sheet Sets (.dst) should reside in the Dsgn folder and will be modified from this location. The archived files, which will be.zip files, will be placed in the folders that correspond with each milestone (Final for Bid, Final for Construction, etc.). Archives should have been performed at the end of each milestone see Section 7.1 Archiving with Sheet Set Manager. Milestone folders save Archived.zip files in these folders NOTE: Electronic plots (PDFs and DWFs) should be saved into the Milestone folders as well, see Section 6.1 File Management Section Record As-Built Drawings for Capital Projects Top Tier Folder: All drawings should be located in this folder ATTENTION Do NOT move or copy the drawing files into the As-Built folder!

5 Sheet Set Manager Most projects should already have a Sheet Set created that should be stored in the Dsgn folder. For the remaining duration of the project the Sheet Set Properties will be modified to reflect the As-Built revisions: ATTENTION Do NOT move, copy or create a new Sheet Set (.dst) unless the files is corrupt always maintain the existing one. Project Drawings It is important to maintain the integrity of the electronic drawings as they stood at the time of the design. In order to do this the files that reside in the Dsgn folder will be modified. Drawing Standards Project drawings CAD Standards are to remain as-is from the time of the design. Since these projects were designed to the current CAD Standard it should not be necessary to update layer names, colors, linetypes, etc. If the project was broken out into several drawings DO NOT combine them into one drawing, maintain each drawing independently. By combining drawings the margin of error is greater since each drawing has individual settings that may not transfer or combine well. DO NOT rename.dwgs this will break the link to the Sheet Set. Delete unused layout tabs if they are not used as part of the final as-built plan set. For example, this plan set only has 7 sheets and the 15746_DSGN_C1.0.dwg has a C18 layout which is not part of the final set, therefore it can be deleted from the drawing: Notice there is no C18 in this list Delete unused layout tabs Section Record As-Built Drawings for Capital Projects

6 New Drawings/Sheets On occasion new drawings (.DWGs) or sheets (layouts) may need to be added to an As-Built plan set. DO NOT use the current template to create these sheets! In both cases remember to add the new sheets to the Sheet Set. Drawings: Open an existing drawing from the same plan set Perform a Save As o Name the drawing accordingly Erase all unneeded data o Leave the Title Block Add pertinent data to the newly created drawing o Create or adjust Viewports as needed Sheets (preferred method): In an existing drawing, copy an existing layout tab right-click the layout tab, select Move or Copy : In the Move or Copy pop-up window check Create a copy, then click <OK>: Erase all unneeded data o Leave the Title Block Add pertinent data to the newly created drawing o Create or adjust Viewports as needed NOTE: Do NOT use the Sheet Set Manager to create new drawings in the As-built phase unless the template has been updated in the Sheet Set Properties Section Record As-Built Drawings for Capital Projects

7 Plotting Project drawings may be set to old plotters, in these cases the Named Page Setups will need to be adjusted to ensure Publishing from the Sheet Set works properly, see Sections 16.0 Plotting & Publishing for more information on Plotting and Publishing. Plot Stamp On DW drawings the plot stamp is part of the Title Block and shall remain on all projects: Internal Tip: Old projects A version of this plot stamp can be found on the DW Design Drafting Tool Palette, this is to be used for old projects missing the plot stamp NOTE: Do not use the Plot Stamp option in the Plot Dialog box. Section Record As-Built Drawings for Capital Projects

8 THIS PAGE INTENTIONALLY LEFT BLANK Section Record As-Built Drawings for Capital Projects

Section Table of Contents: Section 16.0

Section Table of Contents: Section 16.0 Section 16.0 Table of Contents: Section 16.0 Overview - Section 16.0... 16.0-3 Plotting Single Sheets... 16.0-3 Publishing... 16.0-5 Creating DWFs or PDFs (with Sheet Sets)... 16.0-6 Overview - Section

More information

Section Table of Contents: Section 11.0

Section Table of Contents: Section 11.0 Section 11.0 Table of Contents: Section 11.0 Overview - Section 11.0... 11.0-3 Setting a Coordinate System (internal use only)... 11.0-3 Setting a Coordinate System in Sheet Set Properties... 11.0-3 Resetting

More information

Sheets Happen! Using the Sheet Set Manager

Sheets Happen! Using the Sheet Set Manager Sheets Happen! Using the Sheet Set Manager Westwood Professional Services June 2007 Using AutoCAD s Sheet Set Manager Introduction The Sheet Set Manager organizes, displays, and manages sheet sets, a named

More information

Advanced Topics Using the Sheet Set Manager in AutoCAD

Advanced Topics Using the Sheet Set Manager in AutoCAD Advanced Topics Using the Sheet Set Manager in AutoCAD Sam Lucido Haley and Aldrich, Inc. GEN15297 Do you still open drawings one at a time? Do you print drawings one at a time? Do you update the index

More information

Output a drawing layout to a printer, a plotter, or a file. Save and restore the printer settings for each layout.

Output a drawing layout to a printer, a plotter, or a file. Save and restore the printer settings for each layout. Printing Output a drawing layout to a printer, a plotter, or a file. Save and restore the printer settings for each layout. Originally, people printed text from printers and plotted drawings from plotters.

More information

Plotting from Start to Finish With AutoCAD 2004

Plotting from Start to Finish With AutoCAD 2004 December 2-5, 2003 MGM Grand Hotel Las Vegas Plotting from Start to Finish With AutoCAD 2004 Speaker: J.C. Malitzke Assistant: David Harrington Assistant: Shaan Hurley Driver: Craig Black Code: GD11-1L

More information

CBCL Limited Sheet Set Manager Tutorial 2013 REV. 02. CBCL Design Management & Best CAD Practices. Our Vision

CBCL Limited Sheet Set Manager Tutorial 2013 REV. 02. CBCL Design Management & Best CAD Practices. Our Vision CBCL Limited Sheet Set Manager Tutorial CBCL Design Management & Best CAD Practices 2013 REV. 02 Our Vision To be the most respected and successful Atlantic Canada based employeeowned firm, delivering

More information

Section Table of Contents: Section 12.0

Section Table of Contents: Section 12.0 Section 12.0 Table of Contents: Section 12.0 Overview - Section 12.0... 12.0-3 Layers... 12.0-3 Filters... 12.0-3 Layer fields... 12.0-5 Discipline Designaters... 12.0-5 Status (Phase)... 12.0-5 Template

More information

Create all plan and profile sheets in the current drawing. Create all plan and profile sheets in individual drawings.

Create all plan and profile sheets in the current drawing. Create all plan and profile sheets in individual drawings. NOTES Module 18 Roadway Plan Production In this module, you learn how to work with Roadway Plan Production tools in AutoCAD Civil 3D. The Plan Production tools are used to automate the generation of plan

More information

the Buzzsaw file hierarchy, providing bid administrators the ability to easily view and manage all bid-related project documents.

the Buzzsaw file hierarchy, providing bid administrators the ability to easily view and manage all bid-related project documents. What s New: Summary Viewing Enhancements with new PDF and drawing comparison support (Buzzsaw Standard and Buzzsaw Professional): Buzzsaw provides design review and redlining for the latest versions of

More information

Design, Drawing and Sheet Composition

Design, Drawing and Sheet Composition Design, Drawing and Sheet Composition Tools, Technologies and Concepts 1 WWW.BENTLEY.COM 2018 Bentley Systems, Incorporated 2018 Bentley Systems, Incorporated 2 WWW.BENTLEY.COM 2018 Bentley Systems, Incorporated

More information

Wholly Sheets, Batman - Plotting in AutoCAD Civil 3D Seth Cohen Advanced Technologies Solutions Inc.

Wholly Sheets, Batman - Plotting in AutoCAD Civil 3D Seth Cohen Advanced Technologies Solutions Inc. Seth Cohen Advanced Technologies Solutions Inc. CV637 Are you confused about how to plot all the different views (plan, profile, and cross sections) in AutoCAD Civil 3D software? Then this class is for

More information

CSI: CAD Standards Implementation

CSI: CAD Standards Implementation CSI: CAD Standards Implementation Sam Lucido Haley and Aldrich, Inc. IT15277 Did you know that AutoCAD has a CAD Standards Manager? Yes, there is a panel on the Ribbon under the manage tab where you can

More information

Plotting from A to Z

Plotting from A to Z Las Vegas, Nevada, December 3 6, 2002 Speaker Name: J.C. Malitzke Course Title: Plotting from A to Z Course ID: GD23-2 Course Outline: This class offers both AutoCAD veterans and new users the chance to

More information

DIGITAL DATA SUBMISSION STANDARDS Procedures and Guidelines

DIGITAL DATA SUBMISSION STANDARDS Procedures and Guidelines DIGITAL DATA SUBMISSION STANDARDS Procedures and Guidelines 2014 Citizens Wastewater of Westfield - GIS Digital Standards Table of Contents Introduction... 3 Definitions and Terms... 3 Reference Documents...

More information

Submittals Quick Reference Guide

Submittals Quick Reference Guide This topic provides a reference for the Project Center Submittals activity center. Purpose The Submittals activity center in Newforma Contract Management enables you to effectively log submittals and track

More information

Template Drawings. Template Drawings. AutoCAD Essentials

Template Drawings. Template Drawings. AutoCAD Essentials AutoCAD Essentials Starting a new drawing using any CAD software requires a series of steps. Measurement units, sheet size, layer designations, text fonts and text sizes plus many more items must be set.

More information

CADD & Civil 3D User Guidelines

CADD & Civil 3D User Guidelines THURSTON COUNTY PUBLIC WORKS DEPARTMENT Design and Construction Division CADD & Civil 3D User Guidelines V4.0_06_10_15 1 THURSTON COUNTY PUBLIC WORKS DEPARTMENT DESIGN AND CONSTRUCTION DIVISION CADD &

More information

Drawing Layouts Paper space & Model Space

Drawing Layouts Paper space & Model Space Drawing Layouts Paper space & Model Space Users of Bricscad will have seen the tabs at the bottom left of the drawings area labelled: Model, Layout1, Layout2 but may not know how to use them or what they

More information

Mastering. AutoCAD Sheet Sets THE COVER. An Expert Guide

Mastering. AutoCAD Sheet Sets THE COVER. An Expert Guide Mastering THE COVER Qui volore imagnihillit que la nimolora vellorendemporaecab imperit harum que dolor mint faccabori inveles et fugitibus dioris maiones. AutoCAD Sheet Sets An Expert Guide Contents Introduction

More information

1. Difference on the Plot feature between ZWCAD+ and AutoCAD

1. Difference on the Plot feature between ZWCAD+ and AutoCAD Trouble Shooting ---Plot Familiar Problems Analysis 1. Difference on the Plot feature between ZWCAD+ and AutoCAD Plot problem is not only related with the software itself, but also related with the Plotter

More information

Getting Started Guide

Getting Started Guide SOLIDWORKS Getting Started Guide SOLIDWORKS Electrical FIRST Robotics Edition Alexander Ouellet 1/2/2015 Table of Contents INTRODUCTION... 1 What is SOLIDWORKS Electrical?... Error! Bookmark not defined.

More information

Assignment 13 CAD Mechanical Part 2

Assignment 13 CAD Mechanical Part 2 Assignment 13 CAD Mechanical Part 2 Objectives In this assignment you will learn to apply the hatch and break commands along with commands previously learned. General Instructions Hatching 1. When AutoCAD's

More information

NEORSD. Cad Standards and Procedures Manual

NEORSD. Cad Standards and Procedures Manual NEORSD Cad Standards and Procedures Manual This Manual is being provided to you on loan from the NEOSRD and is the property of the NEOSRD. Periodic updates will be provided and you are responsible for

More information

SETTING UP YOUR PAGE LAYOUT:

SETTING UP YOUR PAGE LAYOUT: In this workshop we will look at: Setting up your drawing sheet Viewports Printing your work Once you ve drawn your work in the Model space and you re ready to print, you need to set up your Drawing Sheet

More information

Zooming in on Architectural Desktop Layouts Alexander L. Wood

Zooming in on Architectural Desktop Layouts Alexander L. Wood December 2-5, 2003 MGM Grand Hotel Las Vegas Alexander L. Wood Code BD41-3L Take advantage of both AutoCAD and Autodesk Architectural Desktop Layout features. We'll look at the basics of setting up AutoCAD

More information

Drawing Management Brain Dump

Drawing Management Brain Dump Drawing Management Brain Dump Paul McArdle Autodesk, Inc. April 11, 2003 This brain dump is intended to shed some light on the high level design philosophy behind the Drawing Management feature and how

More information

Reference Project. Chapter

Reference Project. Chapter Chapter 1 Reference Project For many companies, the default standard may not be sufficient. It is a good base for starting a drawing, but there are always specific company symbols and settings that require

More information

Section 1. Introduction and Review. Objectives: Log on to the computer Launch AutoCAD Create, open, and save a drawing Review AutoCAD basics

Section 1. Introduction and Review. Objectives: Log on to the computer Launch AutoCAD Create, open, and save a drawing Review AutoCAD basics Section 1 Introduction and Review Objectives: Log on to the computer Launch AutoCAD Create, open, and save a drawing Review AutoCAD basics Drawing Assignments: NCAA Basketball Court Plot Style Table (Check-off)

More information

G e t t i n g S t a r t e d G u i d e. ID Card Managers. Getting Started Guide. 1 P a g e

G e t t i n g S t a r t e d G u i d e. ID Card Managers. Getting Started Guide. 1 P a g e G e t t i n g S t a r t e d G u i d e ID Card Managers Getting Started Guide 1 P a g e G e t t i n g S t a r t e d G u i d e P a g e 2 Contents ID Cards: Getting Started... 3 Why manage photo ID Cards

More information

A. Section includes administrative and procedural requirements for project record documents, including the following:

A. Section includes administrative and procedural requirements for project record documents, including the following: SECTION 017839 - PROJECT RECORD DOCUMENTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01

More information

Section 4: Ontario Realty Corporation CAD Standards and Guidelines

Section 4: Ontario Realty Corporation CAD Standards and Guidelines Section 4: Ontario Realty Corporation CAD Standards and Guidelines Ontario Realty Corporation 11 th Floor, Ferguson Block 77 Wellesley Street West Queen s Park Toronto, ON, M7A 2G3 August 10, 2007 Version

More information

No Sheet! You can do that with the SSM in AutoCAD

No Sheet! You can do that with the SSM in AutoCAD . No Sheet! You can do that with the SSM in AutoCAD Sam Lucido CAD Services Manager Haley and Aldrich, Inc. @CADproTips Join the conversation #AU2015 Class summary The Sheet Set Manager (SSM) in AutoCAD

More information

Rhinoceros modeling tools for designers. Using Layouts in Rhino 5

Rhinoceros modeling tools for designers. Using Layouts in Rhino 5 Rhinoceros modeling tools for designers Using Layouts in Rhino 5 RH50-TM-LAY-Apr-2014 Rhinoceros v5.0, Layouts, Training Manual Revised April 8, 2014, Mary Fugier mary@mcneel.com Q&A April 8, 2014, Lambertus

More information

Create styles that control the display of Civil 3D objects. Copy styles from one drawing to another drawing.

Create styles that control the display of Civil 3D objects. Copy styles from one drawing to another drawing. NOTES Module 03 Settings and Styles In this module, you learn about the various settings and styles that are used in AutoCAD Civil 3D. A strong understanding of these basics leads to more efficient use

More information

The Microstation configuration must be set up with the correct CAD resource files as outlined in SPEC

The Microstation configuration must be set up with the correct CAD resource files as outlined in SPEC 1/7 1.0 PURPOSE This specification describes the procedure for working with the Vale Drawing Checker Utility. This utility checks the drawing for adherence to many mandatory Vale drawing standards and

More information

Chapter 6 Title Blocks

Chapter 6 Title Blocks Chapter 6 Title Blocks In previous exercises, every drawing started by creating a number of layers. This is time consuming and unnecessary. In this exercise, we will start a drawing by defining layers

More information

by Jonathan Pickup fourth edition written with version 2013 Vectorworks Landmark Tutorial Manual SAMPLE

by Jonathan Pickup fourth edition written with version 2013 Vectorworks Landmark Tutorial Manual SAMPLE kramdnal by Jonathan Pickup fourth edition written with version 2013 Vectorworks Landmark Tutorial Manual Table of Contents Introduction... iii Project 1: Landscape Area Analysis...1 Project 2: Quick Domestic

More information

Vectorworks Architect

Vectorworks Architect SAMPLE by Jonathan Pickup third edition written with version 2011 Vectorworks Architect Tutorial Manual Table of Contents Introduction... iii How to Use this Manual... iii New Ways of Drawing... iv Vectorworks

More information

UT D Substation Design A Brownfield Approach

UT D Substation Design A Brownfield Approach UT10893 3D Substation Design A Brownfield Approach Greg Nightingale SA Power Networks, South Australia. Learning Objectives Learn how to design in 3D with the intention to combine with existing substation

More information

It is expected that this standard will evolve over time; however the use of this standard should remain consistent within individual projects.

It is expected that this standard will evolve over time; however the use of this standard should remain consistent within individual projects. 1.0 Introduction A computer aided design (CAD) procedure is necessary to ensure that drawings produced by and for the University are readable, understandable, of a consistent standard, and, where necessary,

More information

BIM. e Submission Guideline Structural. Annex 1a. Recommended Process Revit 2010

BIM. e Submission Guideline Structural. Annex 1a. Recommended Process Revit 2010 BIM e Submission Guideline Structural Annex 1a Recommended Process Revit 2010 Building and Construction Authority 5 Maxwell Road #16-00 Tower Block MND Complex Singapore 069110 www.bca.gov.sg Revision

More information

AutoCAD Tutorial First Level. 2D Fundamentals. Randy H. Shih SDC. Better Textbooks. Lower Prices.

AutoCAD Tutorial First Level. 2D Fundamentals. Randy H. Shih SDC. Better Textbooks. Lower Prices. AutoCAD 2018 Tutorial First Level 2D Fundamentals Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to

More information

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 12/12/2018

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 12/12/2018 SECTION 01 7839 - PROJECT RECORD DOCUMENTS GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification

More information

Projects Connector User Guide

Projects Connector User Guide Version 4.3 11/2/2017 Copyright 2013, 2017, Oracle and/or its affiliates. All rights reserved. This software and related documentation are provided under a license agreement containing restrictions on

More information

IE11, Edge (current version), Chrome (current version), Firefox (current version)

IE11, Edge (current version), Chrome (current version), Firefox (current version) Quick Start Guide DocuSign for SharePoint Online v3.4 Published: October 13, 2017 Overview DocuSign for SharePoint Online allows users to sign or send documents for signature from a SharePoint Online library.

More information

Version 8 Tutorial

Version 8 Tutorial Version 8 Tutorial 800-989-4243 214-340-9436 support@vertigraph.com www.vertigraph.com 1 Table of Contents A. Overview... 4 B. About the SiteWorx/OS Window... 4 C. File Types Raster, Vector and PDF...

More information

Drawing Management Standard

Drawing Management Standard Record Number: R0000393979 Version Number: 1.0 Date: December 2015 Authorisations Action Name and title Date Prepared by TasNetworks 23/12/2015 Reviewed by David King With input from Rick Stevens, Jeshua

More information

Designing with BIM for Infrastructure on Large Transportation Projects

Designing with BIM for Infrastructure on Large Transportation Projects Designing with BIM for Infrastructure on Large Transportation Projects July 19, 2012, 10:00 a.m. Pacific Time Join civil designer Dave DeJong from Stantec as he discusses how BIM for Infrastructure has

More information

Drawing output in imos ix 2017 SR2. Date of creation: March 2018; last changes Version used: ix 2017 SR2

Drawing output in imos ix 2017 SR2. Date of creation: March 2018; last changes Version used: ix 2017 SR2 Drawing output in imos ix 2017 SR2 Date of creation: March 2018; last changes 13.04.2018 Version used: ix 2017 SR2 We make every effort to ensure the content of this document is complete, accurate and

More information

Working with Process Flow DiagramsChapter1:

Working with Process Flow DiagramsChapter1: Chapter 1 Working with Process Flow DiagramsChapter1: In this chapter, you learn about designing piping with AutoCAD MEP. The design phase consists of conceptualizing, modeling, and documenting the necessary

More information

To apply proposed roadway data (vertical alignments, cross section template data, cut/fill slopes, etc.)

To apply proposed roadway data (vertical alignments, cross section template data, cut/fill slopes, etc.) That CAD Girl J ennifer dib ona Website: www.thatcadgirl.com Email: thatcadgirl@aol.com Phone: (919) 417-8351 Fax: (919) 573-0351 Roadway Design Extracting Existing Ground Cross Sections This document

More information

DocuSign Setup Admin. DocuSign User Setup Process Overview. Setting up a new DocuSign user

DocuSign Setup Admin. DocuSign User Setup Process Overview. Setting up a new DocuSign user DocuSign Setup Admin DocuSign User Setup Process Overview 1) CORE-CT Security receives request to set up new supplier contract document creator 2) CORE-CT security team sets up Roles for the User 3) DocuSign

More information

COURSE: INTRODUCTION TO CAD GRADES: UNIT: Measurement

COURSE: INTRODUCTION TO CAD GRADES: UNIT: Measurement UNIT: Measurement - Students will demonstrate correctness in measuring using various scales and instruments. Demonstrate the various marks that make up a ruler including 1/16, 1/8, ¼ and ½. Assessment

More information

Creating and Editing Plot Style Tables

Creating and Editing Plot Style Tables AutoCAD and Its Applications BASICS Supplemental Material Chapter 28 Creating and Editing Plot Style Tables The plot style tables supplied with AutoCAD are appropriate for many plotting applications. Use

More information

Hexagons for Art and Illusion Part II Get ready Start a new project FILE New Open Faced Cube Import the hexagon block LIBRARIES

Hexagons for Art and Illusion Part II Get ready Start a new project FILE New Open Faced Cube Import the hexagon block LIBRARIES Hexagons for Art and Illusion Part II In our last lesson, we constructed the perfect hexagon using EasyDraw. We built a six pointed star, a solid faced cube, and put the cube inside the star. This lesson

More information

Montana Association of Registered Land Surveyors Conference 2013

Montana Association of Registered Land Surveyors Conference 2013 AutoCAD CIVIL 3D Survey Features - Field to Finish This session is an introduction to the Civil 3D Survey Tools. We will cover some basics of working with Survey Databases and Automated Linework. We will

More information

Creating a 2D Drawing in Paper Space

Creating a 2D Drawing in Paper Space C h a p t e r 16 Creating a 2D Drawing in Paper Space In this chapter, we will learn the following to World Class standards: 1. Converting 3D Solids to 2D Orthographic Views 2. Open the Solid Part Drawing

More information

EC-CAD New features and changes The following improvements have been made to the EC-CAD Product: EC Design to Fabrication.

EC-CAD New features and changes The following improvements have been made to the EC-CAD Product: EC Design to Fabrication. RELEASE NOTES EC Design to Fabrication This document contains summary information on new features, late-breaking product information, updates, and troubleshooting tips not covered in the Trimble EC Design

More information

Mastering AutoCAD 2D

Mastering AutoCAD 2D Course description: Mastering AutoCAD 2D Design and shape the world around you with the powerful, flexible features found in AutoCAD software, one of the world s leading 2D design applications. With robust

More information

Section XV - PER, Design, and Construction Submittal Requirements

Section XV - PER, Design, and Construction Submittal Requirements Section XV - PER, Design, and Construction Submittal Requirements A. Introduction - In an effort to reduce paper and to further implement the Oracle Unifier Project Management System, the Engineering Department

More information

Vectorworks Essentials

Vectorworks Essentials by Jonathan Pickup fourth edition written with version 2012 Vectorworks Essentials Tutorial Manual Contents 0.0 Introduction... iii 0.1 How to Use this Manual... iv 0.2 What s in This Manual... v 0.3 New

More information

Creating and Editing Plot Style Tables

Creating and Editing Plot Style Tables AutoCAD and Its Applications BASICS Supplemental Material Chapter 28 2013 Creating and Editing Plot Style Tables The plot style tables supplied with AutoCAD are appropriate for many plotting applications.

More information

FOCUS ON REAL DESIGN AUTOMATE THE REST CUSTOMTOOLS BATCH CONVERTING YOUR SOLIDWORKS FILES

FOCUS ON REAL DESIGN AUTOMATE THE REST CUSTOMTOOLS BATCH CONVERTING YOUR SOLIDWORKS FILES FOCUS ON REAL DESIGN AUTOMATE THE REST CUSTOMTOOLS BATCH CONVERTING YOUR SOLIDWORKS FILES Table of Contents BATCH CONVERTING YOUR SOLIDWORKS DOCUMENTS... 3 Introduction... 3 What does it do?... 3 How does

More information

Table of Contents. Part I Introduction to CorelCAD Introducing CorelCAD About CorelCAD Benefits of Using CorelCAD...

Table of Contents. Part I Introduction to CorelCAD Introducing CorelCAD About CorelCAD Benefits of Using CorelCAD... Table of Contents Part I Introduction to C 2013.... 1 1 Introducing C 2013.... 3 About C... 4 Benefits of Using C....4 Impressive Compatibility... 4 Familiar User Interface.... 5 Drafting Tools.... 5 Collaboration....

More information

DOTD Plan Delivery. Baton Rouge, LA February 10, 2009 Presented by Hollis Ward DOTD Design Automation Manager

DOTD Plan Delivery. Baton Rouge, LA February 10, 2009 Presented by Hollis Ward DOTD Design Automation Manager DOTD Plan Delivery Moving Ahead Louisiana Transportation Conference 2009 Baton Rouge, LA February 10, 2009 Presented by Hollis Ward DOTD Design Automation Manager Design Automation Manager Role in Plan

More information

UDS OVERVIEW Uniform Drawing System

UDS OVERVIEW Uniform Drawing System UDS OVERVIEW Uniform Drawing System The Construction Specifications Institute 601 Madison Street Alexandria, VA 1994 CSI began development of UDS Organization and presentation of drawing sets Organization

More information

11.0 INSTRUMENTATION LOOP DIAGRAMS

11.0 INSTRUMENTATION LOOP DIAGRAMS 11.0 INSTRUMENTATION LOOP DIAGRAMS Table of Contents 11.0 INSTRUMENTATION LOOP DIAGRAMS... 11-1 11.1 HISTORY OF CHANGE... 11-2 11.2 INSTRUMENT LOOP DIAGRAMS (ILD)... 11-4 11.2.1 Drawing Content... 11-4

More information

Autodesk Inventor Drawing Manager Tips & Tricks

Autodesk Inventor Drawing Manager Tips & Tricks Alessandro Gasso Autodesk, Inc. MA1280 This class covers several workflows that answer the most common questions from the Inventor users about the Drawing Manager. You will learn how to add the scale value

More information

Autodesk University Advanced Topics Using the Sheet Set Manager in AutoCAD

Autodesk University Advanced Topics Using the Sheet Set Manager in AutoCAD Autodesk University Advanced Topics Using the Sheet Set Manager in AutoCAD You guys, some of you I already know, and some of you have seen me before, and you've seen my giant head on the banner out there.

More information

TS 099: Distribution and Sub-Transmission CAD Drafting Standards. Distribution and Sub-Transmission CAD Drafting Standards

TS 099: Distribution and Sub-Transmission CAD Drafting Standards. Distribution and Sub-Transmission CAD Drafting Standards Technical Standard - TS 099 Distribution and Sub-Transmission CAD Drafting Standards Published: 16 May 2016 SA Power Networks www.sapowernetworks.com.au SA Power Networks 2016 Page 1 of 63 Revision Notice:

More information

Tips and Techniques for AutoCAD 2006

Tips and Techniques for AutoCAD 2006 11/30/2005-1:00 pm - 2:30 pm Room:N. Hemispheres (Salon B/C) (Dolphin) Walt Disney World Swan and Dolphin Resort Orlando, Florida Tips and Techniques for AutoCAD 2006 J.C. Malitzke - Moraine Valley Community

More information

Advance Concrete 2014 Service Pack 1

Advance Concrete 2014 Service Pack 1 Advance Concrete 2014 Service Pack 1 This document describes the improvements in Service Pack 1 for Advance Concrete 2014. GENERAL Interaction between Advance Concrete and Advance Steel. Advance Steel

More information

Second Third

Second Third STEP 1: Everything that you draw in is exact. It will be more accurate than you will ever need it to be, All objects drawn on the screen are placed there based on a simple X,Y coordinate system. In this

More information

AutoCAD Standards University of California, Santa Cruz Physical Planning & Construction

AutoCAD Standards University of California, Santa Cruz Physical Planning & Construction University of California, Santa Cruz Physical Planning & Construction 1. General Requirements: 1.1 Format 1.2 Ownership 2. Required Data: 2.1 Area Tabulation 2.2 Drawing Files 2.3 External References 2.4

More information

NTG Technical Drawings

NTG Technical Drawings DEPARTMENT OF INFRASTRUCTURE, PLANNING AND LOGISTICS NTG Technical Drawings Part 1 Requirements for Technical Records Management Approval Sheet Title NTG Technical Drawings Part 1 Requirements for Technical

More information

USING LAYERS. Chapter 18 - Layers 117

USING LAYERS. Chapter 18 - Layers 117 USING LAYERS KNOWLEDGE AND UNDERSTANDING After completing this module, you will know and understand the theory regarding: layers different layer settings the use of layers in templates APPLICATION OF KNOWLEDGE

More information

Tutorial Guide to AutoCAD 2015

Tutorial Guide to AutoCAD 2015 Tutorial Guide to AutoCAD 2015 2D Drawing, 3D Modeling Shawna Lockhart SDC P U B L I C AT I O N S For Microsoft Windows Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

AutoCAD Setup Instructions Manual. March 1, 2018

AutoCAD Setup Instructions Manual. March 1, 2018 AutoCAD Setup Instructions Manual March 1, 2018 1 Contents 2 General Application... 3 2.1 System Requirements... 3 3 Menus and Preferences... 4 3.1 Menu Overview... 5 3.2 Drawing Setup... 7 3.2.1 Paper

More information

MODEL SETUP FOR RENOVATION PROJECTS INSTRUCTIONS AND TUTORIALS

MODEL SETUP FOR RENOVATION PROJECTS INSTRUCTIONS AND TUTORIALS MODEL SETUP FOR RENOVATION PROJECTS INSTRUCTIONS AND TUTORIALS WHAT S INSIDE INTRODUCTION 1 PART ONE LAYERS AND CLASSES FOR RENOVATION PROJECT 1 OVERVIEW 1 SETTING UP LAYERS AND CLASSES 1 CREATING OBJECT

More information

1: INTRODUCTION TO AUTOCAD

1: INTRODUCTION TO AUTOCAD AutoCAD syllabus 1: INTRODUCTION TO AUTOCAD Starting AutoCAD AutoCAD Screen Components Drawing Area Command Window Navigation bar Status bar Invoking Commands in AutoCAD Keyboard Ribbon Application Menu

More information

Student Quick Guide to Progress Reports

Student Quick Guide to Progress Reports Student Quick Guide to Progress Reports 1. To create your progress report, log in to RIMS. The link is http://rims.massey.ac.nz. Use your student id and mymassey password to log in. 2. Under GRS, select

More information

Table of contents. User interface 1: Customizable tool palette... 6 User interface 2: General GUI improvements... 7

Table of contents. User interface 1: Customizable tool palette... 6 User interface 2: General GUI improvements... 7 Table of contents WELCOME TO ADVANCE CONCRETE 2014... 5 USER INTERFACE ENHANCEMENTS... 6 User interface 1: Customizable tool palette... 6 User interface 2: General GUI improvements... 7 MODELING... 10

More information

Exercise 1: The AutoCAD Civil 3D Environment

Exercise 1: The AutoCAD Civil 3D Environment Exercise 1: The AutoCAD Civil 3D Environment AutoCAD Civil 3D Interface Object Base Layer Object Component Layers 1-1 Introduction to Commercial Site Grading Plans AutoCAD Civil 3D Interface AutoCAD Civil

More information

Xcalibur. LCquan. Tutorial. Quantitative Analysis of a Three-Drugs Data Set Software Version 2.8

Xcalibur. LCquan. Tutorial. Quantitative Analysis of a Three-Drugs Data Set Software Version 2.8 Xcalibur LCquan Tutorial Quantitative Analysis of a Three-Drugs Data Set Software Version 2.8 XCALI-97547 Revision A April 2013 2013 Thermo Fisher Scientific Inc. All rights reserved. LCquan, DCMS Link,

More information

GEN22373 Page Setup for Plotting to Scale: Model Versus Paper Space Which Way Is Best for You? James Kendall Casey Arkansas State University-Beebe

GEN22373 Page Setup for Plotting to Scale: Model Versus Paper Space Which Way Is Best for You? James Kendall Casey Arkansas State University-Beebe GEN22373 Page Setup for Plotting to Scale: Model Versus Paper Space Which Way Is Best for You? James Kendall Casey Arkansas State University-Beebe Learning Objectives Discover 3 different methods of plotting

More information

Design for fireplace setting by Ross Ubergang rossu.com.au. gcadplus User Guide v gcad +

Design for fireplace setting by Ross Ubergang   rossu.com.au. gcadplus User Guide v gcad + This chapter focuses on the use of common drawing tools needed to create typical landscape drawings. You will learn to use these draw tools by making an accurate, full-size model of a proposal for a space

More information

CAD for Maintenance Engineers

CAD for Maintenance Engineers Unit 32: Unit code CAD for Maintenance Engineers F/615/1501 Unit level 4 Credit value 15 Introduction There is a growing trend, in part due to the popularity of three-dimensional (3D) Computer Aided Design

More information

Conceptual Underpinnings of AutoCAD MEP

Conceptual Underpinnings of AutoCAD MEP CHAPTER 2 INTRODUCTION Conceptual Underpinnings of AutoCAD MEP AutoCAD MEP (AMEP) is an object-based Computer Aided Design (CAD) software package. It differs from the AutoCAD foundation upon which it is

More information

Kinyun Australia KP : Procedure for Control of Engineering Drawings PROCEDURE FOR CONTROL OF ENGINEERING DRAWINGS

Kinyun Australia KP : Procedure for Control of Engineering Drawings PROCEDURE FOR CONTROL OF ENGINEERING DRAWINGS PROCEDURE FOR CONTROL OF ENGINEERING DRAWINGS 1 General Kinyun has established, documented, implemented and maintains this Quality Procedure for the control of engineering drawings. This procedure defines

More information

AutoCAD 2D. Table of Contents. Lesson 1 Getting Started

AutoCAD 2D. Table of Contents. Lesson 1 Getting Started AutoCAD 2D Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard

More information

Creating Interim & Final Invoices - Basic Steps

Creating Interim & Final Invoices - Basic Steps Creating Invoices in your fp. system is a straightforward and flexible. Please follow the steps in this article, to learn the basics of building interim or final invoices. Refer to other articles to learn

More information

Step It Up a Rung from AutoCAD Designs to AutoCAD Electrical

Step It Up a Rung from AutoCAD Designs to AutoCAD Electrical Step It Up a Rung from AutoCAD Designs to AutoCAD Electrical Todd Schmoock Synergis Technologies MA4762-L: AutoCAD Electrical has proven to be easy for creating electrical controls system designs. It has

More information

ELECTRONIC DRAFTING GUIDELINES

ELECTRONIC DRAFTING GUIDELINES ELECTRONIC DRAFTING GUIDELINES Edition No. 6 Updated November 2016 TABLE OF CONTENTS Section Title Page 1 Definitions 3 2 Drawing Format 3 2.1 Standards & Guidelines 3 2.2 Survey Plans 4 2.3 Underground

More information

Tutorial Guide to AutoCAD 2014

Tutorial Guide to AutoCAD 2014 Tutorial Guide to AutoCAD 2014 2D Drawing, 3D Modeling Shawna Lockhart SDC P U B L I C AT I O N S For Microsoft Windows Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following websites

More information

MODEL SETUP FOR RENOVATION PROJECTS: INSTRUCTIONS AND TUTORIALS

MODEL SETUP FOR RENOVATION PROJECTS: INSTRUCTIONS AND TUTORIALS MODEL SETUP FOR RENOVATION PROJECTS: INSTRUCTIONS AND TUTORIALS TABLE OF CONTENTS INTRODUCTION 1 PART ONE LAYERS AND CLASSES FOR RENOVATION PROJECT 2 OVERVIEW 2 SETTING UP LAYERS AND CLASSES 2 CREATING

More information

Heredis may assign any number of information sources to each event.

Heredis may assign any number of information sources to each event. Sources Sources Heredis may assign any number of information sources to each event. Each source is an independent element, which is then assigned to one or more events. Heredis allows you the flexibility

More information

Best Practices For Consultants

Best Practices For Consultants Best Practices For Consultants Electronic Submission of Engineering Drawings Last Updated June 2015 Table of Contents 1.0 Overview... 1 2.0 Technical Requirements... 2 2.1 Browser... 2 2.2 Pop-Up Blockers...

More information

Tutorial Guide to AutoCAD 2013

Tutorial Guide to AutoCAD 2013 Tutorial Guide to AutoCAD 2013 2D Drawing, 3D Modeling Shawna Lockhart SDC P U B L I C AT I O N S Schroff Development Corporation For Microsoft Windows Better Textbooks. Lower Prices. www.sdcpublications.com

More information

Practice Workbook. Cross Sections: Creating, Annotating, and Volumes. SELECTseries 4 ( ) or newer

Practice Workbook. Cross Sections: Creating, Annotating, and Volumes. SELECTseries 4 ( ) or newer Practice Workbook This workbook is designed for use in Live instructor-led training and for OnDemand self study. The explanations and demonstrations are provided by the instructor in the classroom, or

More information