Racing Car Design using Solid Edge A Short Tutorial

Size: px
Start display at page:

Download "Racing Car Design using Solid Edge A Short Tutorial"

Transcription

1 Racing Car Design using Solid Edge A Short Tutorial In the next few minutes, students and/or teachers will model a simple racecar using Solid Edge TM. With a little more practice, far more complicated race winning designs can be achieved. Here we will use Solid Edge Part to create a 3D Solid that is then ready to be manufactured! This document assumes knowledge of Microsoft Windows and have gone through the online tutorials found under the help menu, even better if you have received training from Denford. Copy the template file F1 In Schools to <Drive letter>:\program files\solid edge V11\templates Step 1. Start Solid Edge, Start>programs>Solid Edge>Part. Start a new file Choose F1 In Schools.par. In The new file, there is a surface block representing the boundaries of the balsa wood block and a series of profiles which we are going to use to model a racing car. Step 2. Choose the Lofted Protrusion command from the left hand application tool bar and select the from sketch option on the smart step ribbon bar. 28/10/2003 Page1 of 21 EDS PLM Solutions

2 Select the profile Main Body Profile 1 highlighted ensure the dot is in the bottom left shown by the arrow. 28/10/2003 Page2 of 21 EDS PLM Solutions

3 Next select Main Body Profile 2 again ensuring that the dot is at the bottom left of the profile. 28/10/2003 Page3 of 21 EDS PLM Solutions

4 Next select Main Body Profile 3 This completes the cross section stage so now move on by selecting the guide curve step on the ribbon bar 28/10/2003 Page4 of 21 EDS PLM Solutions

5 We will now select the guide curves and after selecting each one either select green tick on ribbon bar or select enter from keyboard select all the Main Body Guide Curves as shown in dark blue. Now select preview. 28/10/2003 Page5 of 21 EDS PLM Solutions

6 Your model should look like this. Next we will model the front nose cone using a lofted protrusion in the same way using Profiles Main Body Profile 3 Nose Cone Profile 1 and Nose Cone Profile 2 (Point) and guide curves Nose Cone Guide Curve 1 and Main Body Guide Curve 3. Select Lofted Protrusion command then on the smartstep ribbon bar ensure the select option is on sketch/chain and select the two profiles as shown 28/10/2003 Page6 of 21 EDS PLM Solutions

7 Next change the select options on the ribbon bar to point and select the point Nose Cone Profile 2 as shown. We have selected all the profiles so on the smartstep ribbon bar change move along to the guide curve step and change to the from sketch option as shown 28/10/2003 Page7 of 21 EDS PLM Solutions

8 Now select the two guide curves shown selecting each one by enter or the green tick on the ribbonbar 28/10/2003 Page8 of 21 EDS PLM Solutions

9 Select Preview from the ribbon bar the model should now look like this That s the main body complete we will now use the protrusion command to model the airfoils, as before the profiles have been created for you so on the ribbon bar select the from sketch option. Now select the two profiles for the airfoil, front and rear this will then move you on to the extent step ensure the symmetric extent button value of 76 is selected and key in a 28/10/2003 Page9 of 21 EDS PLM Solutions

10 Now lets see how much you have remembered using the loft command create the front wheel support using the profiles as shown remember to select the same corner on each profile in this case there are no guide curves. If in doubt have a look at what you did to create the body. 28/10/2003 Page10 of 21 EDS PLM Solutions

11 28/10/2003 Page11 of 21 EDS PLM Solutions

12 Now do the same thing for the rear axle as shown 28/10/2003 Page12 of 21 EDS PLM Solutions

13 If you have the same result as above well done, we now need to do the same thing on the other side so we are going to mirror the feature about the centre using the mirror feature command. Ensure reference planes are turned on either using the construction display icon or RMB and select show all reference planes. Now select the mirror feature icon note it may not be shown remember any icon with an arrow in bottom left corner has a pullout, once you have done it a few times you will soon get to know where the relevant tools are. On the ribbon bar change the option from fast to smart pattern then select the lofted protrusion you have just created either from the edgebar or the screen and holding the cntrl key down select the rear wheel protrusion as well then select the green tick or enter to move to the next step, now select the x-z reference plane see below and finish 28/10/2003 Page13 of 21 EDS PLM Solutions

14 Your car is now taking shape, lets have a look at creating the cockpit, for this you need to select the cutout icon from the feature toolbar. As before select the from sketch icon now select the cockpit profile followed by the green check mark that will move you along the ribbon bar to the next step and be prompted for extent, select the through next option, and move the cursor so that the red arrow points towards the top of the car the result should be as shown. 28/10/2003 Page14 of 21 EDS PLM Solutions

15 We now need to put the regulation slot and hole for the gas canister into the rear of the model. By now you should be getting used to the process profile step/side step then the extent step. So to model the slot select the cutout icon then select from sketch next select the rectangular cutout slot profile, as this is an open profile you will need to identify which side the material will be cut away, so point the arrow inside then for the extent select through next from the ribbon bar. To model the cutout for the cylinder the process is exactly the same, select the cylinder profile as it is a closed profile it will not ask for a side, it will move straight onto extent select finite extent and key in then make sure the material is remioved from the model by moving the cursor so the cylinder is towards the model then LMB the result should be as shown below. 28/10/2003 Page15 of 21 EDS PLM Solutions

16 28/10/2003 Page16 of 21 EDS PLM Solutions

17 We now need to put some holes in for the axle to go through, so using the cutout place a 3mm hole through the wheel support as shown. Select the hole and for extent use the through next option from the ribbon bar. Lets do the same thing for the rear wheels again use the cutout from sketch and through next for the extent. All that remains is to do some aesthetic rounding. 28/10/2003 Page17 of 21 EDS PLM Solutions

18 Round 2mm Round 3mm 28/10/2003 Page18 of 21 EDS PLM Solutions

19 Round 3mm Round 3mm Round 10mm 28/10/2003 Page19 of 21 EDS PLM Solutions

20 Round 0.3mm Round 2mm Round 5mm 28/10/2003 Page20 of 21 EDS PLM Solutions

21 Your car should now look something similar to the one below, experiment with the features to build your own unique racecar. 28/10/2003 Page21 of 21 EDS PLM Solutions

Activity 1 Modeling a Plastic Part

Activity 1 Modeling a Plastic Part Activity 1 Modeling a Plastic Part In this activity, you will model a plastic part. When completed, your plastic part should look like the following two illustrations. While building this model, take time

More information

Introduction to Autodesk Inventor for F1 in Schools (Australian Version)

Introduction to Autodesk Inventor for F1 in Schools (Australian Version) Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital

More information

SolidWorks Design & Technology

SolidWorks Design & Technology SolidWorks Design & Technology Training Course at PHSG Ex 5. Lego man Working with part files 8mm At first glance the Lego man looks complicated but I hope you will see that if you approach a project one

More information

Getting Started. Right click on Lateral Workplane. Left Click on New Sketch

Getting Started. Right click on Lateral Workplane. Left Click on New Sketch Getting Started 1. Open up PTC Pro/Desktop by either double clicking the icon or through the Start button and in Programs. 2. Once Pro/Desktop is open select File > New > Design 3. Close the Pallet window

More information

SolidWorks Tutorial 1. Axis

SolidWorks Tutorial 1. Axis SolidWorks Tutorial 1 Axis Axis This first exercise provides an introduction to SolidWorks software. First, we will design and draw a simple part: an axis with different diameters. You will learn how to

More information

Solid Part Four A Bracket Made by Mirroring

Solid Part Four A Bracket Made by Mirroring C h a p t e r 5 Solid Part Four A Bracket Made by Mirroring This chapter will cover the following to World Class standards: Sketch of a Solid Problem Draw a Series of Lines Finish the 2D Sketch Extrude

More information

Cube in a cube Fusion 360 tutorial

Cube in a cube Fusion 360 tutorial Cube in a cube Fusion 360 tutorial n Before using these instructions, it is helpful to watch this video screencast of the CAD drawing actually being done in the software. Click to link to the video tutorial.

More information

Introduction to Circular Pattern Flower Pot

Introduction to Circular Pattern Flower Pot Prerequisite Knowledge Previous knowledge of the sketching commands Line, Circle, Add Relations, Smart Dimension is required to complete this lesson. Previous examples of Revolved Boss/Base, Cut Extrude,

More information

The Revolve Feature and Assembly Modeling

The Revolve Feature and Assembly Modeling The Revolve Feature and Assembly Modeling PTC Clock Page 52 PTC Contents Introduction... 54 The Revolve Feature... 55 Creating a revolved feature...57 Creating face details... 58 Using Text... 61 Assembling

More information

Engineering Technology

Engineering Technology Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,

More information

Here are the standard pre-requisites for the training course. Potential students should have or completed the following prior to the class:

Here are the standard pre-requisites for the training course. Potential students should have or completed the following prior to the class: Course: Solid Edge Fundamentals Duration: 5 days Version: ST8 At Course Completion Students will have learned how to utilize Solid Edge to design production level parametric (ordered) models of parts,

More information

Welcome to SPDL/ PRL s Solid Edge Tutorial.

Welcome to SPDL/ PRL s Solid Edge Tutorial. Smart Product Design Product Realization Lab Solid Edge Assembly Tutorial Welcome to SPDL/ PRL s Solid Edge Tutorial. This tutorial is designed to familiarize you with the interface of Solid Edge Assembly

More information

Table of Contents. Lesson 1 Getting Started

Table of Contents. Lesson 1 Getting Started NX Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard

More information

Using Google SketchUp

Using Google SketchUp Using Google SketchUp Opening sketchup 1. From the program menu click on the SketchUp 8 folder and select 3. From the Template Selection select Architectural Design Millimeters. 2. The Welcome to SketchUp

More information

Part 8: The Front Cover

Part 8: The Front Cover Part 8: The Front Cover 4 Earpiece cuts and housing Lens cut and housing Microphone cut and housing The front cover is similar to the back cover in that it is a shelled protrusion with screw posts extruding

More information

Introduction To Modeling

Introduction To Modeling Introduction To Modeling Introduction ProEngineer Wildfire2 is a computer aided design (CAD) program that is used to create models on a computer in three-dimensions. Since three dimensions are used the

More information

1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry

1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry 4.1: Modeling 3D Modeling is a key process of getting your ideas from a concept to a read- for- manufacture state, making it core foundation of the product development process. In Fusion 360, there are

More information

Introduction to Sheet Metal Features SolidWorks 2009

Introduction to Sheet Metal Features SolidWorks 2009 SolidWorks 2009 Table of Contents Introduction to Sheet Metal Features Base Flange Method Magazine File.. 3 Envelopment & Development of Surfaces.. 14 Development of Transition Pieces.. 23 Conversion to

More information

Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008

Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008 1 Introduction This lab is designed to provide you with basic skills when using the 3D modeling program SolidWorks. You will learn how to build parts, assemblies and drawings. You will be given a physical

More information

EXERCISE ONE: BEACH BUGGY.

EXERCISE ONE: BEACH BUGGY. EXERCISE ONE: BEACH BUGGY. Prerequisite knowledge Students should have completed Exercises from the file: Introduction to Assemblies Concept Mates Focus of lesson Commands Used This lesson will focus on

More information

Bottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch.

Bottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch. Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click

More information

Pull Down Menu View Toolbar Design Toolbar

Pull Down Menu View Toolbar Design Toolbar Pro/DESKTOP Interface The instructions in this tutorial refer to the Pro/DESKTOP interface and toolbars. The illustration below describes the main elements of the graphical interface and toolbars. Pull

More information

Evaluation Chapter by CADArtifex

Evaluation Chapter by CADArtifex The premium provider of learning products and solutions www.cadartifex.com EVALUATION CHAPTER 2 Drawing Sketches with SOLIDWORKS In this chapter: Invoking the Part Modeling Environment Invoking the Sketching

More information

Getting started with. Getting started with VELOCITY SERIES.

Getting started with. Getting started with VELOCITY SERIES. Getting started with Getting started with SOLID EDGE EDGE ST4 ST4 VELOCITY SERIES www.siemens.com/velocity 1 Getting started with Solid Edge Publication Number MU29000-ENG-1040 Proprietary and Restricted

More information

SolidWorks Navigation

SolidWorks Navigation SolidWorks Basics SolidWorks Navigation Command Bar Feature Tree Model Window Simple Box Select the Front plane Create a new sketch Create a Center Rectangle from the origin Smart Dimension the length

More information

DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY

DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY CAPSULE PROGRAM Funded by NSF grant #0833636 Tutorial 02 3D Part Modeling SolidWorks 2010 Copyright 2010 Prof. Zeid 3D Part Modeling

More information

SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI

SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered

More information

F1 in Schools Tutorial 1 A Step by Step Guide To Drawing a. Bloodhound Block In SolidWorks

F1 in Schools Tutorial 1 A Step by Step Guide To Drawing a. Bloodhound Block In SolidWorks F in Schools Tutorial A Step by Step Guide To Drawing a Bloodhound Block In SolidWorks There are 7 Achievement Points to Collect During This Tutorial! Requirements: SolidWorks Student Edition or SolidWorks

More information

Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar.

Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar. Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click

More information

CREO.1 MODELING A BELT WHEEL

CREO.1 MODELING A BELT WHEEL CREO.1 MODELING A BELT WHEEL Figure 1: A belt wheel modeled in this exercise. Learning Targets In this exercise you will learn: Using symmetry when sketching Using pattern to copy features Using RMB when

More information

Hydro Hull. Chapter 21. Boat. A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2).

Hydro Hull. Chapter 21. Boat. A. Save as HYDRO. Step 1. Open your HULL MID PLANE file (Chapter 2). Chapter 21 Boat Hydro Hull A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2). Step 2. Click File Menu > Save As. Step 3. Key-in HYDRO for the filename and press ENTER. B. Delete Loft1,

More information

Virtual components in assemblies

Virtual components in assemblies Virtual components in assemblies Publication Number spse01690 Virtual components in assemblies Publication Number spse01690 Proprietary and restricted rights notice This software and related documentation

More information

Introducing SolidWorks

Introducing SolidWorks Introducing SolidWorks SAAST Robotics 2008 SolidWorks Software Visually-based 3-D Mechanical design software Engineers and Designers use it to: Quickly sketch out ideas Experiment with features, dimensions

More information

AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.

AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here. AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and

More information

for Solidworks TRAINING GUIDE LESSON-9-CAD

for Solidworks TRAINING GUIDE LESSON-9-CAD for Solidworks TRAINING GUIDE LESSON-9-CAD Mastercam for SolidWorks Training Guide Objectives You will create the geometry for SolidWorks-Lesson-9 using SolidWorks 3D CAD software. You will be working

More information

Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated)

Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) Inventor (5) Module 2: 2-1 Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) In this tutorial, we will learn how to build a 3D model

More information

Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece

Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece 1 Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece In this Module, we will explore the method of adding dovetail seams to curved edges such as the circumferential edge of a

More information

Alibre Design Tutorial - Simple Extrude Step-Pyramid-1

Alibre Design Tutorial - Simple Extrude Step-Pyramid-1 Alibre Design Tutorial - Simple Extrude Step-Pyramid-1 Part Tutorial Exercise 4: Step-Pyramid-1 [text version] In this Exercise, We will set System Parameters first. Then, in sketch mode, outline the Step

More information

Session 3: Getting to Know Photoshop Elements. Keep in mind that there are many others ways of solving the problems.

Session 3: Getting to Know Photoshop Elements. Keep in mind that there are many others ways of solving the problems. Tutorial Session 3: Getting to Know Photoshop Elements Now that you have taken some pictures you might have noticed that some of the images have little problems like red-eye, colorcast, and too dark or

More information

Datum Tutorial Part: Cutter

Datum Tutorial Part: Cutter Datum Tutorial Part: Cutter Objective: Learn to apply Datums in different ways Directions 1. Datum Axis Creation a. First we need to create a center axis for the cutter b. Model Tab > Datum > Select Axis

More information

Drawing Layouts Paper space & Model Space

Drawing Layouts Paper space & Model Space Drawing Layouts Paper space & Model Space Users of Bricscad will have seen the tabs at the bottom left of the drawings area labelled: Model, Layout1, Layout2 but may not know how to use them or what they

More information

Using Siemens NX 11 Software. The connecting rod

Using Siemens NX 11 Software. The connecting rod Using Siemens NX 11 Software The connecting rod Based on a Catia tutorial written by Loïc Stefanski. At the end of this manual, you should obtain the following part: 1 Introduction. Start NX 11 and open

More information

Toothbrush Holder. A drawing of the sheet metal part will also be created.

Toothbrush Holder. A drawing of the sheet metal part will also be created. Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson; Sketch (Line, Centerline, Circle, Add Relations, Smart Dimension,), Extrude Boss/Base, and Edit

More information

When you complete this assignment you will:

When you complete this assignment you will: Objjectiives When you complete this assignment you will: 1. sketch and dimension circles and arcs. 2. cut holes in the model using the cut feature of the extrusion command. 3. create Arcs using the trim

More information

The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly.

The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly. Introduction - Teacher Notes Fig 1. The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly. Pro/DESKTOP enables pupils (and teachers) to communicate and model

More information

< Then click on this icon on the vertical tool bar that pops up on the left side.

< Then click on this icon on the vertical tool bar that pops up on the left side. Pipe Cavity Tutorial Introduction The CADMAX Solid Master Tutorial is a great way to learn about the benefits of feature-based parametric solid modeling with CADMAX. We have assembled several typical parts

More information

Digital Camera Exercise

Digital Camera Exercise Commands Used New Part This lesson includes Sketching, Extruded Boss/Base, Extruded Cut, Fillet, Chamfer and Text. Click File, New on the standard toolbar. Select Part from the New SolidWorks Document

More information

Spatula. Spatula SW 2015 Design & Communication Graphics Page 1

Spatula. Spatula SW 2015 Design & Communication Graphics Page 1 Spatula Introduction: The model shown in the picture is made of three parts, - the base, the washer and the handle. The base requires the use of Spline and Style Spline command, Slot command and Mirror

More information

Siemens NX11 tutorials. The angled part

Siemens NX11 tutorials. The angled part Siemens NX11 tutorials The angled part Adaptation to NX 11 from notes from a seminar Drive-to-trial organized by IBM and GDTech. This tutorial will help you design the mechanical presented in the figure

More information

F1 in Schools Tutorial 3 A Step by Step Guide To Drawing an. F1 Block In SolidWorks

F1 in Schools Tutorial 3 A Step by Step Guide To Drawing an. F1 Block In SolidWorks F in Schools Tutorial A Step by Step Guide To Drawing an F Block In SolidWorks There are 7 Achievement Points to Collect During This Tutorial! Requirements: SolidWorks Student Edition or SolidWorks Design

More information

10/14/2010. Chevy Malibu. Vehicle Design with Solidworks. Start SolidWorks Create a New SolidWorks Document. Miles, Rowardo B

10/14/2010. Chevy Malibu. Vehicle Design with Solidworks. Start SolidWorks Create a New SolidWorks Document. Miles, Rowardo B Chevy Malibu Vehicle Design with Solidworks Start SolidWorks Create a New SolidWorks Document Miles, Rowardo B 1 Click: Part and then OK Now you are ready to make a Part. 2 Right Toolbar: Document Properties:

More information

Creo Extrude Tutorial 2: Cutting and Adding Material

Creo Extrude Tutorial 2: Cutting and Adding Material Creo Extrude Tutorial 2: Cutting and Adding Material 1. Open Creo Parametric 2. File > Open > extrudeturial (From Creo Extrude Tutorial 1) 3. Cutting Material a. Click Extrude Icon > Select the following

More information

Introduction to CATIA V5

Introduction to CATIA V5 Introduction to CATIA V5 Release 17 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower

More information

Wireless Mouse Surfaces

Wireless Mouse Surfaces Wireless Mouse Surfaces Design & Communication Graphics Table of Contents Table of Contents... 1 Introduction 2 Mouse Body. 3 Edge Cut.12 Centre Cut....14 Wheel Opening.. 15 Wheel Location.. 16 Laser..

More information

Advanced CO2 car Import CAM Procedures

Advanced CO2 car Import CAM Procedures Advanced CO2 car Import CAM Procedures While the standard CO2 car tutorial within Quick CAM has a part that is sized to fit the billet as custom designed cars are produced this will not be the case. Before

More information

SolidWorks 95 User s Guide

SolidWorks 95 User s Guide SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents

More information

Part Design Fundamentals

Part Design Fundamentals Part Design Fundamentals 1 Course Presentation Objectives of the course In this course you will learn basic methods to create and modify solids features and parts Targeted audience New CATIA V5 Users 1

More information

Lesson 4 Extrusions OBJECTIVES. Extrusions

Lesson 4 Extrusions OBJECTIVES. Extrusions Lesson 4 Extrusions Figure 4.1 Clamp OBJECTIVES Create a feature using an Extruded protrusion Understand Setup and Environment settings Define and set a Material type Create and use Datum features Sketch

More information

CREATE A BURNT EDGE EFFECT

CREATE A BURNT EDGE EFFECT CREATE A BURNT EDGE EFFECT One of the all-time classic effects in Photoshop is the burnt edge, and there s lots of different ways to create it, but in this Adobe Photoshop tutorial, we re going to look

More information

Inventor Activity 5: Lofted Vase

Inventor Activity 5: Lofted Vase Inventor Activity 5: Lofted Vase In this tutorial, you will use a few new commands to create a free form Lofted object. Sometimes you want to create an object that is not made up of square, flat, or perfectly

More information

NX 7.5. Table of Contents. Lesson 3 More Features

NX 7.5. Table of Contents. Lesson 3 More Features NX 7.5 Lesson 3 More Features Pre-reqs/Technical Skills Basic computer use Completion of NX 7.5 Lessons 1&2 Expectations Read lesson material Implement steps in software while reading through lesson material

More information

TOY TRUCK. Figure 1. Orthographic projections of project.

TOY TRUCK. Figure 1. Orthographic projections of project. TOY TRUCK Prepared by: Harry Hawkins The following project is of a small, wooden toy truck. This exercise will provide you with the procedure for constructing the various parts of the design then assembling

More information

Lesson 4 Holes and Rounds

Lesson 4 Holes and Rounds Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information

More information

Engineering & Computer Graphics Workbook Using SolidWorks 2014

Engineering & Computer Graphics Workbook Using SolidWorks 2014 Engineering & Computer Graphics Workbook Using SolidWorks 2014 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

Name: Date Completed: Basic Inventor Skills I

Name: Date Completed: Basic Inventor Skills I Name: Date Completed: Basic Inventor Skills I 1. Sketch, dimension and extrude a basic shape i. Select New tab from toolbar. ii. Select Standard.ipt from dialogue box by double clicking on the icon. iii.

More information

Creo Revolve Tutorial

Creo Revolve Tutorial Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate

More information

Engineering & Computer Graphics Workbook Using SOLIDWORKS

Engineering & Computer Graphics Workbook Using SOLIDWORKS Engineering & Computer Graphics Workbook Using SOLIDWORKS 2017 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

Canoe Mirroring Lofts

Canoe Mirroring Lofts Canoe Mirroring Lofts 1. Set Units to Inches 2. Create a New Design. 3. Save the Design as canoeinl811 in your Canoe folder. 4. Create a New Sketch on the Frontal Workplane. Name the Sketch Middle. 5.

More information

Drawing and Assembling

Drawing and Assembling Youth Explore Trades Skills Description In this activity the six sides of a die will be drawn and then assembled together. The intent is to understand how constraints are used to lock individual parts

More information

AutoCAD Tutorial First Level. 2D Fundamentals. Randy H. Shih SDC. Better Textbooks. Lower Prices.

AutoCAD Tutorial First Level. 2D Fundamentals. Randy H. Shih SDC. Better Textbooks. Lower Prices. AutoCAD 2018 Tutorial First Level 2D Fundamentals Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to

More information

Model House Exercise-( Extrude)

Model House Exercise-( Extrude) -( Extrude) Prerequisite knowledge Focus of the lesson Commands Used This lesson requires an understanding of using the sketch commands including Inserting a new sketch Adding sketch geometry Understanding

More information

Sheet metal tutorial. To set the bend radius Right click on the first sheet metal icon in the command manager and specify a bend radius or 1mm.

Sheet metal tutorial. To set the bend radius Right click on the first sheet metal icon in the command manager and specify a bend radius or 1mm. Sheet metal tutorial In the following tutorial you will cover the basic features of the Solid Works sheet metal tool by modelling the component shown opposite. Activating Sheet metal mode Sheet metal components

More information

TABLE OF CONTENTS. INTRODUCTION...5 Advance Steel...5 Where to find information?...6 Contacting technical support...6

TABLE OF CONTENTS. INTRODUCTION...5 Advance Steel...5 Where to find information?...6 Contacting technical support...6 TABLE OF CONTENTS INTRODUCTION...5 Advance Steel...5 Where to find information?...6 Contacting technical support...6 INSTALLATION...7 System requirements...7 Starting the installation...7 STARTING ADVANCE

More information

Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1

Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Part Tutorial Exercise 5: Loft-Tube-1 [Complete] In this Exercise, We will set System Parameters first, then part options. Then, in sketch

More information

Working With Drawing Views-I

Working With Drawing Views-I Chapter 12 Working With Drawing Views-I Learning Objectives After completing this chapter you will be able to: Generate standard three views. Generate Named Views. Generate Relative Views. Generate Predefined

More information

Excel Tool: Plots of Data Sets

Excel Tool: Plots of Data Sets Excel Tool: Plots of Data Sets Excel makes it very easy for the scientist to visualize a data set. In this assignment, we learn how to produce various plots of data sets. Open a new Excel workbook, and

More information

Excel Lab 2: Plots of Data Sets

Excel Lab 2: Plots of Data Sets Excel Lab 2: Plots of Data Sets Excel makes it very easy for the scientist to visualize a data set. In this assignment, we learn how to produce various plots of data sets. Open a new Excel workbook, and

More information

Introduction to Autodesk Inventor User Interface Student Manual MODEL WINDOW

Introduction to Autodesk Inventor User Interface Student Manual MODEL WINDOW Emmett Wemp EDTECH 503 Introduction to Autodesk Inventor User Interface Fill in the blanks of the different tools available in the user interface of Autodesk Inventor as your instructor discusses them.

More information

Modeling an Airframe Tutorial

Modeling an Airframe Tutorial EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If

More information

UNIVERSITY OF SHEFFIELD; LANDSCAPE DEPARTMENT AUTOCAD 2013/14/15 TUTORIALS - SESSION 2 SESSION TWO

UNIVERSITY OF SHEFFIELD; LANDSCAPE DEPARTMENT AUTOCAD 2013/14/15 TUTORIALS - SESSION 2 SESSION TWO SESSION TWO In this session we will look at another drawing tool HATCH and some more modifying / editing tools EXTEND, FILLET, MIRROR, SCALE and RECTANGULAR ARRAY. We will also look at LAYERS, LINETYPE,

More information

Tutorial 1 getting started with the CNCSimulator Pro

Tutorial 1 getting started with the CNCSimulator Pro CNCSimulator Blog Tutorial 1 getting started with the CNCSimulator Pro Made for Version 1.0.6.5 or later. The purpose of this tutorial is to learn the basic concepts of how to use the CNCSimulator Pro

More information

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2005 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com

More information

Getting Started. Before You Begin, make sure you customized the following settings:

Getting Started. Before You Begin, make sure you customized the following settings: Getting Started Getting Started Before getting into the detailed instructions for using Generative Drafting, the following tutorial aims at giving you a feel of what you can do with the product. It provides

More information

Revit Structure 2013 Basics

Revit Structure 2013 Basics Revit Structure 2013 Basics Framing and Documentation Elise Moss Supplemental Files SDC P U B L I C AT I O N S Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Tutorial

More information

Solid Edge structural frames and weldments

Solid Edge structural frames and weldments Siemens PLM Software Solid Edge structural frames and weldments White Paper Intelligent, process-specific applications that speed time to manufacturing. www.siemens.com/plm A white paper issued by: Siemens

More information

Architecture 2012 Fundamentals

Architecture 2012 Fundamentals Autodesk Revit Architecture 2012 Fundamentals Supplemental Files SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Tutorial files on enclosed CD Visit

More information

Shaft Hanger - SolidWorks

Shaft Hanger - SolidWorks ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric

More information

Draw IT 2016 for AutoCAD

Draw IT 2016 for AutoCAD Draw IT 2016 for AutoCAD Tutorial for System Scaffolding Version: 16.0 Copyright Computer and Design Services Ltd GLOBAL CONSTRUCTION SOFTWARE AND SERVICES Contents Introduction... 1 Getting Started...

More information

CAD Orientation (Mechanical and Architectural CAD)

CAD Orientation (Mechanical and Architectural CAD) Design and Drafting Description This is an introductory computer aided design (CAD) activity designed to give students the foundational skills required to complete future lessons. Students will learn all

More information

CAMWorks How To Create CNC G-Code for CO2 Dragsters

CAMWorks How To Create CNC G-Code for CO2 Dragsters Creating the Left Side Smooth Finish Tool Path. This chapter will focus on the steps for creating the left side smooth finish tool path. The objective of this chapter is to create to an accurate and highly

More information

Principles and Practice

Principles and Practice Principles and Practice An Integrated Approach to Engineering Graphics and AutoCAD 2011 Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation

More information

ACAD-BAU TUTORIAL For BricsCAD platform

ACAD-BAU TUTORIAL   For BricsCAD platform ACAD-BAU TUTORIAL WWW.ARHINOVA.SI For BricsCAD platform August 06 WORKSPACE ACAD-BAU RIBBON ACAD-BAU CONTROL BAR F ACAD-BAU PALETTES BASIC SETTINGS Use New command and open the template called ACB_International.DWT.

More information

Welcome to Corel DESIGNER, a comprehensive vector-based package for technical graphic users and technical illustrators.

Welcome to Corel DESIGNER, a comprehensive vector-based package for technical graphic users and technical illustrators. Workspace tour Welcome to Corel DESIGNER, a comprehensive vector-based package for technical graphic users and technical illustrators. This tutorial will help you become familiar with the terminology and

More information

CAD Tutorial 24: Step by Step Guide

CAD Tutorial 24: Step by Step Guide CAD TUTORIAL 24: Step by step CAD Tutorial 24: Step by Step Guide Level of Difficulty Time Approximately 40 50 minutes Lesson Objectives To understand the basic tools used in SketchUp. To understand the

More information

High Speed Motion Trail Effect With Photoshop

High Speed Motion Trail Effect With Photoshop High Speed Motion Trail Effect With Photoshop Written by Steve Patterson. In this Photo Effects tutorial, we'll learn how to add a sense of speed to an object using an easy to create motion blur effect!

More information

Apex v5 Assessor Introductory Tutorial

Apex v5 Assessor Introductory Tutorial Apex v5 Assessor Introductory Tutorial Apex v5 Assessor Apex v5 Assessor includes some minor User Interface updates from the v4 program but attempts have been made to simplify the UI for streamlined work

More information

Starting a New Drawing with a Title Block and Border

Starting a New Drawing with a Title Block and Border Starting a New Drawing with a Title Block and Border From the File menu select New. Within the New file menu toggle the option Drawing, name the file and turn Off the toggle Use Default Template. Select

More information