ASME B31.3 INTERPRETATIONS NO. 13
|
|
- Kristopher Peters
- 6 years ago
- Views:
Transcription
1 /. '.... _,' ASME B31.3 INTERPRETATIONS NO Replies to Technical Inquiries April 1, 1994, Through March 31, 1995 General Information It has been agreed to publish interpretations issued by the B31 Committee concerning B31.3 as part of the update service to the Code. The interpretations have been assigned numbers in chronological order. Each interpretation applies to the Edition or Aqdenda stated in the interpretation, or if none is stated, to the Edition or Addenda in effect on the date of issuance of the interpretation. Subsequent revisions to the Code may have superseded the reply. These interpretations are not part of the Code or its Addenda. These replies are taken verbatim from the original letters, except for a few typographical and editorial corrections made for the purpose of improved clarity. In some instances, a review of the interpretation revealed a need for corrections of a technical nature. In these cases, a revised reply bearing the original interpretation number with the suffix R is presented. ASME.procedures provide for reconsideration of these interpretations when or if additional information 'is available which the inquirer believes might affect the interpretation. Further, persons aggrieved by an interpretation may appeal to the cognizant ASME committee or subcommittee. As stated in the Statement of Poli~ in the Code documents, ASME does not "approve," "certify," "rate," or "endorse" any item, construction, proprietary device, or activity. For detailed instructions on preparaion of technical inquiries to the B31 Committee, refer to Appendix Z. Code Reference and Subject Indexes Code Reference and Subject Indexes have been prepared to assist. the user in locating interpretations by location or by subject matter in the Code. They cover interpretations issued from Volume 1 up to and including the present volume, and will be updated with each volume. 147
2 : ~.. '. -: Subject Alteration of Existing Piping and Hot Tapping '. Certification of a Listed Material to Another Listed Material Specification. Paras and , Design Pressure. Para (a), Pressure Design of Straight Pipe. Para , Pressure Design of Unlisted Components and Elements. Paras. 304,7.2 and (d), Pressure Design of Unlisted Components and Elements. Paras and , Pressure Design and Flexibility Factors. Para , Flexibility Analysis. Para , Preparation for Welding. Para , Welded Branch Connections. Chapter VI Inspection, Examination, and Testing. Para (e), Progressive Examination. Para (a), Hydrostatic Test Requirements. Para , Pneumatic Testing. Para. A , Heat Fusion Joints in Thermoplastic Piping. Appendix X, Para. X3.2.2, Metallic Bellows Expansion Joints. Intery,retation '()2 13'()3 '13-05, '() : ,13.Q File No Q34 B B31 94'() () ()37 B31 94.() Q " /",-.. :; ~ t : '. " -: ,. l.:.~ ~~. ' ~, " i; 149
3 B31.3 Interpretations No , 13-62, Interpretation: ASME B Edition, Para , Preparation for Welding B Question: In accordance with ASME B Edition, Addenda a, does the Code require that all transitional tapers be filled with weld metal to obtain a consistent outside diameter when welding together two weld end components that are manufactured to include all of the following: (1) a weld bevel to nominal wall thickness; (2) an actual outside diameter greater than the nominal outside diameter; (3) a taper transition from the actual outside diameter to the nominal outside diameter weld bevel per ASME BI6.25, Fig. 1.. Reply: No, the weld must have at least the same nominal wall thickness as the thinner of the two components. Interpretation: ASME B Edition, Para , Pressure Design of Unlisted Cqmponents and Elements Date Issued: Nov~mber 21, 1994 B Question: In accordance with ASME B Edition, para , may the maximum allowable pressure of an unlisted component be greater than the manufacturer's rating? Reply: Yes, see para. 300(c)(2). Interpretation: ASME B Edition, Paras and (d), Pressure Design of Unlisted Components and Elements B Question: In accordance with ASME B Edition, is a proof pressure test, in accordance with para (c), required to qualify a flange design not in accordan~ with a listed standard if the design meets the requirements of para (d) as well as the introductory requirements of para ? Reply: No. 151
4 13 04, 13.05, B31.3 Interpretations No. 13 Interpretation: ASME B Edition, Alterations of Existing Piping and Hot Tapping r... \;.' ',~:" B Question: Does ASME B Edition and Addenda a apply to alterations of existing piping, including tie-in branch connections, e.g., hot taps? ' Reply: No. Interpretation: ASME B Edition, Para , Pressure Design qfunlisted Components and Elements, and Para Flexibility and Stress Intensification Factors B Question (1): In accordance with ASME B Edition, maya pressure containing piping component, not manufactured in accordance with a listed standard, and for which the rules in para. 304 do not apply, be qualified in accordance with para ? Reply'(1): Yes. Question (2): In accordance with para , may stress intensification factors for pressure containing piping components~ not manufactured in accordance with a listed standard listed in Appendix D, be established by fatigue testing? Reply (2): Yes. Interpretation: ASME B Edition, Para , Pneumatic Testing B Question: In accordance with ASME B Edition and Addenda a, is it allowable to pneumatically test above 110% of design pressure? Reply: No, unless otherwise specified in the engineering design.,', " " 152
5 B31.3 Interpretations No , Interpretation: ASME B Edition, Para (a), Pressure Design of Straight Pipe B Question: In accor.dance with ASME B Edition, may the minimum pipe wall thickness determined by measurement be used to satisfy the requirements of para, (a)? Reply: Yes. Interpretation: ASME B Edition, Para. A , Heat Fusion Joints in Thermoplastic Piping B Question: Does ASME B Edition, para. A , apply to electrofusion bonding of polyolefin pipe and fittings? Reply: No. Eleetrofusion joints are not listed; see para. A
6 13 09, B31.3 Interpretations No. 13 Interpretation: ASME B Edition, Appendix X, Para. X3.2.2, Metallic Bellows Expansion Joints B Question (1): In accordance with ASME B Edition, para. X3.2.2, is it required to examine inaccessible surfaces of the bellows longitudinal seam weld after forming using liquid penetrant? Reply (1): No. Question (2): Is a dye penetrant leak test (putting dye penetrant on :the inside surface and developer on the weld outside surface) an acceptable alternative to liquid p~netrant examination of the inside surface of bellows longitudinal seam welds? Reply (2): No. Question (3): Are the rules in ASME Section VIII, Division 1, Appendix 26, applicable to bellows in ASME B31.3 piping systems? Reply (3): No. Interpretation: ASME B Edition, Certification of a Listed Material to Another Listed Material Specification. B Question: Is it permissible under the requirements of ASME B Edition for an organization to recertify a listed material to another listed material specification? Reply: B31.3 does not establish rules for materials certification other than the requirements of the materials specifications. 154
7 B31.3 Interpretations No , 13.12, Interpretation: ASME B Edition, Para , Welded Branch Connections B Question: In accordance with ASME B Edition, Addenda a, what is the effective weld throat thickness required for a proprietary integrally reinforced branch 'connection fitting? Reply: The thickness is as required by the manufacturer's design qualified in accordance with para or MSS SP-94, and para (d). Interpretation: ASME B Edition, Para (e), Progressiv~ Examination B Question: In accordance with ASME B Edition, para (e), what is the meaning of the phrase "all items represented by the progressive examinations."? Reply: All items withia- the same designated lot. See para Definitions, random exami nations. Interpretation: ASME B Edition, Para (a), Hydrostatic Test Requirements B Question: Does ASME B Edition, Addenda a, permit a hydrostatic test pressure less than 1.5 times design pressure? Reply: No, unless para (c) or (b) applies. 155
8 13 14, 13 15, B31.3 Interpretations No. 13 Interpretation: ASME B Edition, Para , Flexibility Analysis ~...," \:1... "'., ~ B Question: In accordance with para , how many years of operatio~ or numberofoperating cycles are required to quil1ify a piping system as having a succ~ssful servic~ record? Reply: Such determination is the responsibility of the designer. See para. 300(b)(2). Interpretation: ASME B Edition, Paras and , Design Pressure B Question: When a valve isolates two process streams so that one condition on one side of the valve occurs at the same time as another condition occurs on the other side of the valve, are the requirements of paras and met if the pressure design is based on the most severe conditions of coincident pressure and component temperature? Reply: Yes. Interpretation: ASME B Edition, Chapter VI Inspection, Examination, and Testing B31-94-o59 Question (1): In accordance with ASME B Edition, Addenda a, if a weld has not penetrated to the inside comer of the root face on one side of the joint and the remainder of the weld is sound, does ASME B31.3 classify this defect as lack of fusion? Reply (1): No, refer to Fig sketch (c). Question (2): Can lack of fusion occur at the root of a groove weld joint? Reply (2): Yes. Question (3): Is 1.5 in. of incomplete penetration in any 6 in. weld length for girth and miter groove welds acceptable for normal fluid service? Reply (3): Yes, per acceptance criteria listed in Table A. 156
ASME B31.3 INTERPRETATIONS NO. 11
,..,.- r, ASME B31.3 INTERPRETATIONS NO. 11 Replies to Technical Inquiries April 1,1992, Through March 31,1993 'I General Information,It has been agreed to publish interpretations issued by the B31 Committee
More informationASME B31.3 INTERPRETATIONS NO.9,
ASME B31.3 INTERPRETATIONS NO.9,, t, Replies to Technical Inquiries June 1, 1990, Through March 31, 1991 General Information It has been agreed to publish interpretations issued by the B31 Committee concerning
More informationASME INTERPRETATIONS NO. 19
ASME 831.3 INTERPRETATIONS NO. 19 Replies to Technical Inquiries April 1, 2001 through October 31, 2003 General Information It has been agreed to publish interpretations issued by the B31 Committee concerning
More informationInterpretations No. 1 to ANSI/ASME 831.8
Interpretations No. 1 to ANSI/ASME 831.8 (This supplement Is not part of ANSIIASME 831.8 or the Addenda It is included for Information only.) It has been agreed to publish lnterpretations issued by the
More informationFORM A-1P MANUFACTURER'S DATA REPORT FOR PLATE HEAT EXCHANGERS As Required by the Provisions of the ASME Code Rules, Section VIII, Division 2
Page of FORM A-1P MANUFACTURER'S DATA REPORT FOR PLATE HEAT EXCHANGERS As Required by the Provisions of the ASME Code Rules, Section VIII, Division 2 1. Manufactured and certified by: 2. Manufactured for:
More informationThis specification describes the minimum requirements for piping systems for the following service:
201/01/13 1/ 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Air Design Conditions Operating Conditions Blast Air (see Note 1)
More informationThis specification describes the minimum requirements for piping systems for the following service:
SPEC-3501 1/ 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Instrument Air Design Conditions 150 PSIG @ 180 F Operating Conditions 125
More informationASME BPV XI Interpretation Handout May 10, 2017
ASME BPV XI Interpretation Handout May 10, 2017 Interpretation# 16-2355 and Code Change pg. 2-4 Interpretation# 16-2701 pg. 5 Interpretation# 16-2702 pg. 6 Interpretation# 17-765 pg. 7 1 of 7 Revised Question
More informationThis specification describes the minimum requirements for piping systems for the following service:
SPEC-3004 1/7 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Service Water Design Conditions Operating Conditions 10 PSIG @ 33 o F to
More informationThis specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface.
SPEC-3500 1/9 1.0 PURPOSE This specification describes the minimum requirements for service water piping systems (ie: cooling water, process water, etc.), located on surface. Note: This specification does
More informationNote: Do not bury sulphur dioxide lines Use stainless steel pipe and fittings only where specified on project drawings.
1/7 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Liquid and High Pressure Gaseous Dry Sulphur Dioxide (Less than 100 ppm of water)
More informationAnnexure - V. Specifications, Typical Drawing & Data Sheet for Split TEE (Hot Tapping Material)
Annexure - V Specifications, Typical Drawing & Data Sheet for Split TEE (Hot Tapping Material) CONTENTS SL NO. DESCRIPTION 1.0 SCOPE 2.0 REFERENCE DOCUMENTS 3.0 MANUFACTURER'S QUALIFICATION 4.0 MATERIALS
More informationCopyright ASME International Provided by IHS under license with ASME No reproduction or networking permitted without license from IHS
The American Society of Mechanical Engineers ì N A M E R I C A N N A T I O N A L S T A N D A R D FACTORY-M AD E WROUGHT BUTTWELDING FITTINGS ASME B16.l-2003 (Revision of ASME BI 8.9.2001) Date of Issuance:
More informationSpecification for Horizontal End Suction Centrifugal Pumps for Chemical Process
ASME B73.1-2012 [Revision and Consolidation of ASME B73.1-2001 (R2007) and ASME B73.5M-1995 (R2007)] Specification for Horizontal End Suction Centrifugal Pumps for Chemical Process AN AMERICAN NATIONAL
More informationCast Copper Alloy Solder Joint Drainage Fittings: DWV
ASME B16.23-2011 [Revision of ASME B16.23-2002 (R2006)] Cast Copper Alloy Solder Joint Drainage Fittings: DWV AN AMERICAN NATIONAL STANDARD ASME B16.23-2011 [Revision of ASME B16.23-2002 (R2006)] Cast
More informationANSI ORIFICE FLANGES METAL-KOREA
METAL-KOREA ANSI ORIFICE FLANGES ORIFICE FLANGES are widely used in conjunction with orifice meters for measuring the rate of flow of liquids and gases. They are basically the same as standard welding
More informationCOMPLETE REVISION October Process Industry Practices Piping. PIP PNFJ8000 Jacketed Piping Fabrication and Installation Details
COMPLETE REVISION October 2007 Process Industry Practices Piping PIP PNFJ8000 Jacketed Piping Fabrication and Installation Details PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize
More informationSECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING
SECTION 230516 - EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationWrought Copper and Wrought Copper Alloy Solder-Joint Drainage Fittings DWV
ASME B16.29-2017 (Revision of ASME B16.29-2012) Wrought Copper and Wrought Copper Alloy Solder-Joint Drainage Fittings DWV AN AMERICAN NATIONAL STANDARD ASME B16.29-2017 (Revision of ASME B16.29-2012)
More informationHSB Global Standards ASME Code Changes and Discussions
HSB Global Standards ASME Code Changes and Discussions Presented by: David M. Allore Field Services Manager September 12, 2012 AGENDA Guidelines for AI Review of Design Calculations Frequent Mistakes on
More informationThis specification describes the minimum requirements for piping systems for the following service:
201/11/2 1/9 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Underground Service Water Note: This specification does not apply to piping
More informationA. Compatibility: Products shall be suitable for piping service fluids, materials, working pressures, and temperatures.
SECTION 22 05 16 LOOPS FOR PLUMBING PIPING PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationMachine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series)
ASME B18.6.3-2010 [Revision and Consolidation of ASME B18.6.3-2003 (R2008) and B18.6.4-2009] Machine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series) A N A M E R I C A N N A T I O N A L
More informationFORM Q-120 PROCEDURE SPECIFICATION FOR CLASS II VESSELS (Revision C 2017) Part I Fabrication
FORM Q-120 Part I Fabrication PROCEDURE SPECIFICATION NUMBER: NOTE: Procedure Specification Form Q-120 for Class II vessels consists of three parts. Part I, Fabrication, shall be completed for each separately
More informationINGAA Foundation Workshop - Industry Initiatives Regarding Welding of Field Segmented Induction Bends and Elbows for Pipeline Construction
INGAA Foundation Workshop - Industry Initiatives Regarding Welding of Field Segmented Induction Bends and Elbows for Pipeline Construction October 20, 2011 Steve Rapp, P.E. Spectra Energy Transmission
More informationASME B (Revision of ASME B ) Orifice Flanges
(Revision of ASME B16.36-1996) Orifice Flanges A N A M E R I C A N N A T I O N A L S T A N D A R D (Revision of ASME B16.36-1996) Orifice Flanges AN AMERICAN NATIONAL STANDARD Three Park Avenue New ork,
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 12096 First edition 1996-05-01 Submerged arc-welded steel tubes for pressure purposes - Radiographit testing of the weld seam for the detection of imperfections Tubes en acier
More informationRS/2/C/003MR Published August RATING STANDARD for the certification of Rigid Metallic Ductwork Systems with Rectangular Cross-section
RATING STANDARD for the certification of Rigid Metallic Ductwork Systems with Rectangular Cross-section Editing (date): Marie-Clémence DEGALLAIX (30/05/2016) Checking (date): Jean FOURCROY (02/06/2016)
More informationEssex County College - West Essex Campus Addition And Renovations dlb # / SECTION EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING
SECTION 230516 - EXPANSION FITTINGS AND LOOPS FOR HVAC PIPING PART I - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More information0.20. Record Page 1 of 19
Page 1 of 19 Page 2 of 19 Page 3 of 19 Page 4 of 19 Page 5 of 19 ASME BPVC.III.1.ND-2015 Page 6 of 19 ð15þ Figure ND-3325-1 Some Acceptable Types of Unstayed Flat Heads and Covers GENERAL NOTE: The illustrations
More informationANSI B16.25 Fig. 1 - Maximum Envelope for Welding End Transitions
Fig. 1 - Maximum Envelope for Welding End Transitions Notes: 1 - Where transitions using maximum slope do not intersect inside or outside surface, as shown by phantom outlines, maximum slopes shown or
More informationRules for Inservice Inspection of Nuclear Power Plant Components
2013 ASME Boiler and Pressure Vessel Code AN INTERNATIONAL CODE XI Rules for Inservice Inspection of Nuclear Power Plant Components 29. 2013 ASME FINAL Covers_XI Rules Nuc MECH 5.9.indd 1 5/15/13 5:09
More informationKerkau Manufacturing. B16.5 Flange Book
Kerkau Manufacturing B16.5 Flange Book TABLE OF CONTENTS Revision 1 Title Page Table of Contents Tolerance Page Permissible Imperfections Dimensions of Flange Facings (all pressure rating classes) Dimensions
More informationMachine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series)
ASME B18.6.3-2013 (Revision of ASME B18.6.3-2010) Machine Screws, Tapping Screws, and Metallic Drive Screws (Inch Series) AN AMERICAN NATIONAL STANDARD ASME B18.6.3-2013 (Revision of ASME B18.6.3-2010)
More informationPage 1 of 12 Second Revision No. 5-NFPA 12-2014 [ Section No. 2.3.4 ] 2.3.4 ASTM Publications. ASTM International, 100 Barr Harbor Drive, P.O. Box C 700, West Conshohocken, PA 19428-2959. ASTM A53, Standard
More informationCalculations per ABS Code along with ASME Sec. VIII Div.1 XXXX
Calculations per ABS Code along with ASME Sec. VIII Div.1 XXXX Grouping of Boilers and Pressure Vessels: PART 4 CHAPTER 4 SECTOIN 1 Table #2 and #3 >> Group II PART 4 CHAPTER 4 SECTOIN 1 Appendix 1 Rules
More informationTR2000 Piping and Valve Materials under PED. The usage of this standard based on ASME B31.3
Memo 2010-12-01 (rev. 2) To Copy From Trælnes, Hege Subject TR2000 Piping and Valve Materials under PED. The usage of this standard based on ASME B31.3 1 Introduction and objective Reference is made to
More informationSECTION VIII. ASME Boiler and Pressure Vessel Code An International Code. Div ision 1 ASME BPVC.VI I I
ASME BPVC.VI I I.1-2017 SECTION VIII R u l e s f o r C o n stru cti o n o f P re ssu re Ves s els 2017 ASME Boiler and Pressure Vessel Code An International Code Div ision 1 Markings such as ASME, ASME
More informationConformance of Roll Formed Internal Threads to AS8879 Written by ALMA December 20, 2010
CHAIRMAN OF THE BOARD Karl G. Hutter Click Bond, Inc. TECHNICAL COMMITTEE CHAIRMAN Michael J. Lawler SPS Technologies EXECUTIVE DIRECTOR Robert H. Ecker MEMBERS ALCOA FASTENING SYSTEMS BRISTOL INDUSTRIES
More informationA comprehensive pipework prefabrication service PES PIPEWORK ENGINEERING SERVICES LIMITED
A comprehensive pipework prefabrication service PES PIPEWORK ENGINEERING SERVICES LIMITED Whatever your pipework requirements WE CAN DELIVER Established in 1982, Pipework Engineering Services has earned
More informationASME Boiler and Pressure Vessel Code AN INTERNATIONAL CODE VIII. Rules for Construction of Pressure Vessels. Division 1
2013 ASME Boiler and Pressure Vessel Code AN INTERNATIONAL CODE VIII Rules for Construction of Pressure Vessels Division 1 AN INTERNATIONAL CODE 2013 ASME Boiler & Pressure Vessel Code 2013 Edition July
More informationAmerican Petroleum Institute Task Group Line Pipe
American Petroleum Institute Task Group Line Pipe Work Item 4185 Evaluate the Differences in Acceptance Criteria for Linear Indications in SAW Pipe Work Item Charge To consider if changes to the API Spec
More information-SQA- SCOTTISH QUALIFICATIONS AUTHORITY. Hanover House 24 Douglas Street GLASGOW G2 7NQ NATIONAL CERTIFICATE MODULE DESCRIPTOR
-SQA- SCOTTISH QUALIFICATIONS AUTHORITY Hanover House 24 Douglas Street GLASGOW G2 7NQ NATIONAL CERTIFICATE MODULE DESCRIPTOR -Module Number- 4281040 -Session-1990-91 -Superclass- TH -Title- GAS DISTRIBUTION:
More informationASME B (Revision of ASME B ) Orifice Flanges --``,`,,`,```,,,,,`,,```,,,,,`,-`-`,,`,,`,`,,`---
(Revision of ASME B16.36-2006) Orifice Flanges A N A M E R I C A N N A T I O N A L S T A N D A R D Металлопрокат и трубы по стандартам DIN, EN, ASTM Поставляем металлопрокат по стандарту ASME B16.36 Для
More informationJIS G3465 Seamless Steel Tubes for Drilling
JIS G3465 Seamless Steel Tubes for Drilling 1. Scope This Japanese Industrial Standard specifies the seamless steel tubes, hereinafter referred to as the "tubes", used for casing tube, core tube and drill
More informationSPECIFICATION FOR PIPEWORK WELDING, INSPECTION, SUPPORTING AND TESTING
SPECIFICATION FOR PIPEWORK WELDING, INSPECTION, SUPPORTING AND TESTING CU11 14/11/2012 Page 1 of 108 Contents SECTION 1: SPECIFICATION FOR PIPEWORK WELDING INSPECTION AND TESTING GENERAL CLASSIFICATION
More informationWelding 2 go. alhuzaim_af [Type the company name] 8/2/2012
2012 Welding 2 go alhuzaim_af [Type the company name] 8/2/2012 One must try by doing the thing; for though you think you know it, you have no certainty until you try. - Sophocles 2 I would like to express
More informationA Full Line of Pipe Products for Any Application
Standard Pipe SureThread and ERW: Setting the standard in the standard pipe industry With a tradition of service and quality that s 80-plus years strong, Wheatland Tube is the only domestic, full-line
More informationSocket Wrenches, Handles, and Attachments
ASME B107.110-2012 (Redesignation and Consolidation of ASME B107.1, B107.2, B107.5M, B107.10, B107.12, B107.33M, and B107.34) Socket Wrenches, Handles, and Attachments AN AMERICAN NATIONAL STANDARD ASME
More informationBRAZING PROCEDURE SPECIFICATION NO
NATIONAL CERTIFIED PIPE WELDING BUREAU BRAZING PROCEDURE SPECIFICATION NO. 107-1 FOR TORCH BRAZING OF ALLOYS 102, 120, 122, 142, 192 OF TUBE, VALVES, FITTING AND FLANGES USING BcuP-3 THROUGH-7 FILLER METALS
More informationAS Australian Standard STEEL WIRE FOR TENDONS IN PRESTRESSED CONCRETE. This is a free 5 page sample. Access the full version online.
AS 1310 1987 Australian Standard STEEL WIRE FOR TENDONS IN PRESTRESSED CONCRETE This Australian Standard was prepared by Committee BD/23, Structural Steel. It was approved on behalf of the Council of the
More informationNVIC March 1968 NAVIGATIONS AND VESSEL INSPECTION CIRCULAR NO Tensile Fasteners
UNITED STATES COAST GUARD COMMANDANT (MMT-4) U.S. COAST GUARD WASHINGTON, DC 20591 NVIC 3-68 21 March 1968 NAVIGATIONS AND VESSEL INSPECTION CIRCULAR NO. 3-68 Subj: Tensile Fasteners 1. Purpose. The purpose
More informationSECTION VIII. ASME Boiler and Pressure Vessel Code An International Code. Div ision 2 A lter n ative Ru les ASME BPVC.VI I I.
ASME BPVC.VI I I.2-2017 SECTION VIII R u l e s f o r C o n stru cti o n o f P re ssu re Ves s els 2017 ASME Boiler and Pressure Vessel Code An International Code Div ision 2 A lter n ative Ru les Markings
More informationSpecifications for EA31002 U Tube Bundle for CDU 3
Specifications for EA31002 U Tube Bundle for CDU 3 Tube Bundle Specificatio Tube Bundle for Heat Exchanger EA31002A/B/C/D Quantity required : One with Dummy shell Exchanger Type: BEU Horizontal No of U
More informationSECTION IX. ASME Boiler and Pressure Vessel Code An International Code ASME B PVC.I X-2017
ASME B PVC.I X-2017 SECTION IX We l d i n g, Br a zi n g, a n d Fu sin g Qu alific ations 2017 ASME Boiler and Pressure Vessel Code An International Code Qual i fi cat i on St and ard for We l d i ng,
More informationSMAW LESSON #1: Initiating and maintaining an arc using the scratch start method
SMAW LESSON #1: Initiating and maintaining an arc using the scratch start method OBJECTIVE: Upon completion of this lesson the learner will be able to strike and maintain an arc using SMAW on steel plate
More informationPROPOSAL PAGE 1 OF 5 Revision 3, 4/21/2016. Inquiry: Is it permissible in Section I construction to utilize
PROPOSAL PAGE 1 OF 5 Case 2697 Unstayed Flat Head Constructed From Forged Material Section I Inquiry: Is it permissible in Section I construction to utilize flat heads with integral flanges constructed
More informationThese introduction pages will give a
HGG s Profiling Shapes Welcome to the world of Profiling Shapes. HGG s shapes have several distinct advantages as minimum grinding, easy fitting and optimised weld preparation for rapid welding and strong
More informationAsme B31 1 Power Piping Design Standard Certification
ASME B31 1 POWER PIPING DESIGN STANDARD CERTIFICATION PDF - Are you looking for asme b31 1 power piping design standard certification Books? Now, you will be happy that at this time asme b31 1 power piping
More information(R) Aerospace First Article Inspection Requirement FOREWORD
AEROSPACE STANDARD AS9102 Technically equivalent to AECMA pren 9102 Issued 2000-08 Revised 2004-01 REV. A Supersedes AS9012 (R) Aerospace First Article Inspection Requirement FOREWORD In December 1998,
More informationISO INTERNATIONAL STANDARD. Non-destructive testing of welds Radiographic testing Part 1: X- and gamma-ray techniques with film
INTERNATIONAL STANDARD ISO 17636-1 First edition 2013-01-15 Non-destructive testing of welds Radiographic testing Part 1: X- and gamma-ray techniques with film Contrôle non destructif des assemblages soudés
More informationConnections. Forged Branch. Elbow&LateralConnections... 19
Trans-O-Con@ Forged Branch Connections Specifications............................... 15 Trans-O-Con Features &Applications........... 16 Trans-O-Con Industry Standard Consolidation.... 17 Butt-Weld.................................
More informationPROBAD. Code-based Strength calculations of Pressure parts. PROBAD Release January 2018 New Features and Improvements
PROBAD Code-based Strength calculations of Pressure parts PROBAD Release January 2018 New Features and Improvements The program system PROBAD is checked and modified continuously within the scope of the
More informationEngineering Policy & Procedure
FPD > Engineering > Global Standards Engineering Policy & Procedure Revision History Number: G2-4 Section: G Subject: Radiographic Examination Procedure 1.0 SCOPE This procedure specifies the requirements
More informationWeldment Visual Inspection Requirements
Table of Contents 1.0 Purpose / Scope / Timing... 2 1.1 Purpose / Scope... 2 1.2 Compliance Date... 2 2.0 Procedure / Quality Recd Requirements... 2 2.1 General Requirements... 2 2.2 Acceptance Criteria...
More informationLengths [7] Ø.50 [13] [7] [13]
Dimensions in [ ] are in millimeters Standard (2 1 / 2 6 ) Standard (9 24 ).75 STEM.40 [10] EXTERNAL THREAD.61 [15] 1.00 [25] STEM STEM Ø.44 [11] Threaded-Stepped Shank Standard Stem Length Length (T)
More informationModule 4 Design for Assembly IIT BOMBAY
Module 4 Design for Assembly Lecture 8 Case Studies - IV Instructional objectives The objective of this lecture is to exhibit how real components are designed in industry following some of the principles
More informationA. Radius elbows with a construction radius of 1.5 the duct width are preferred to square elbows.
SECTION 233100 DUCTWORK 1.0 Acoustical duct lining in any part of the duct system is prohibited. All ductwork requiring insulation shall be externally insulated (Refer to the Sheet Metal Ductwork Insulation
More informationQUALITY ASSURANCE SPECIFICATION
Page 1 of 8 QAS: 2.02 QUALITY ASSURANCE SPECIFICATION REVISION: 0 DATE: 08/29/14 MATERIAL PURCHASING Code Material Purchase Specification for Pipe, Valves, Fitting, and Flanges PAGE 1 OF 8 1.0 Purpose
More informationSTP-NU CODE COMPARISON REPORT
CODE COMPARISON REPORT for Class 1 Nuclear Power Plant Components CODE COMPARISON REPORT for Class 1 Nuclear Power Plant Components Prepared for: Multinational Design Evaluation Programme Codes and Standards
More informationFace-to-Face and End-to-End Dimensions of Valves
ASME B16.10-2017 (Revision of ASME B16.10-2009) Face-to-Face and End-to-End Dimensions of Valves AN AMERICAN NATIONAL STANDARD ASME B16.10-2017 (Revision of ASME B16.10-2009) Face-to-Face and End-to-End
More informationA representative from Occupational Health is to be involved in the commissioning process to address any Respiratory Protection Program requirements.
SPEC-3017 1/8 1.0 PURPOSE This specification describes the minimum requirements for the installation of breathing air distribution systems (indoor and outdoor) up to the connection to the breathing air
More information(AMMA) American Maritime Modernization Association
(AMMA) American Maritime Modernization Association AUDIT GUIDE FOR THE EVALUATION OF AMMA MEMBER WELDING, BRAZING, AND NON-DESTRUCTIVE TESTING (NDT) PROGRAMS Revised By: Joe Frith, AMMA Welding/Brazing/NDT
More informationFlange Dimensions Class 125 Bronze Flange Dimensions Class 300 Bronze Flange Dimensions Class 150 Bronze Flange Dimensions
Dimensions Class Bronze Dimensions Meets Ib. A.S.M.E. Stard Class 00 Bronze Dimensions Meets ANSI STD B. Nominal Dim. A O.D. Dim. B Circle Dim. C Hole No. Holes Nominal Dim. A Diam. Dim. B Min. Dim. C
More informationA Full Line of Pipe Products for Any Application
Standard Pipe Standard Pipe: SureThread and ERW Setting the standard in the standard pipe industry With a tradition of service and quality that s 80-plus years strong, Wheatland Tube is the only domestic,
More informationSix-Liter Water Closets Equipped With a Dual Flushing Device
ASME A112.19.14-2013 [Revision of ASME A112.19.14-2006 (R2011)] Six-Liter Water Closets Equipped With a Dual Flushing Device AN AMERICAN NATIONAL STANDARD ASME A112.19.14-2013 [Revision of ASME A112.19.14-2006
More informationNational Craft Assessment and Certification Program S P E C I F I C A T I O N S. INDUSTRIAL BOILERMAKER - MAINTENANCE V4 RBLMK34_04 October 2014
National Craft Assessment and Certification Program S P E C I F I C A T I O N S INDUSTRIAL BOILERMAKER - MAINTENANCE V4 October 2014 Focus Statement A journey level industrial boilermaker in maintenance
More informationNEW APPROACH TO THE PIPE TO GUSSET PLATE CONNECTION
NEW APPROACH TO THE PIPE TO GUSSET PLATE CONNECTION Prepared by Liftech Consultants Inc. Quality Assurance Review for Liftech Consultants Inc. Author: Kenton Lee Structural Engineer Editor: Erik Soderberg
More informationUnit4 31. UnitS 39. Unit 6 47
Preface..................... xi About the Author......... xiii Acknowledgments... xiv Unit 1 1 Bases for Interpreting Drawings........ I Visible Lines............. 3 Lettering on Drawings... 3 Sketching...
More informationТРУБЫ, ФЛАНЦЫ, КРЕПЕЖ, ДЕТАЛИ ТРУБОПРОВОДА СТАНДАРТАМ: ASME, DIN, NF, UNI, EN, JIS И ДР. ПО МЕЖДУНАРОДНЫМ INMOTEH.RU +7 (495) INMOTEH.
+7 (495) 133-39-24 INMOTEH.RU ТРУБЫ, ФЛАНЦЫ, КРЕПЕЖ, ДЕТАЛИ ТРУБОПРОВОДА ПО МЕЖДУНАРОДНЫМ СТАНДАРТАМ: ASME, DIN, NF, UNI, EN, JIS И ДР. INMOTEH.RU ДАННЫЙ МАТЕРИАЛ ПРЕДОСТАВЛЕН ИСКЛЮЧИТЕЛЬНО ДЛЯ ОЗНАКОМЛЕНИЯ
More informationThe use of Mechanical Connectors throughout Life of Field
The use of Mechanical Connectors throughout Life of Field Andrew Woodward Subsea Sales Engineer andrew.woodward@hydratight.com 1 What I will cover Safety Moment Introduction to Hydratight What are Mechanical
More informationChapter VI Vessel Supports
Chapter VI Vessel Supports 1 2 Vessel Supports Vessel support is to a. Support the weight of the container b. Fix the container position c. Keep the container in operation. Classified by the type of vessels:
More informationNew generation of welding and inspection systems
New generation of welding and inspection systems Throughout the pipeline industry, and particularly in offshore and spool base production, welding requirements are shifting toward higher quality, greater
More informationACF Maintenance Bulletin. TC-200 Revision B. ACF 200 Stub Sill Underframe Inspection, Repair, and Enhancement
ACF Maintenance Bulletin TC-200 Revision B ACF 200 Stub Sill Underframe Inspection, Repair, and Enhancement May 16, 2016 SHEET: 1 of 13 FOREWORD: This ACF Maintenance Bulletin TC-200 details the inspection
More informationStandards and Competencies
Skill Performance The skill performance assessment includes the completion of a metal project and a demonstration of the ability to weld carbon steel, aluminum or stainless-steel project in various using
More informationActivating Your Ideas. In Stainless Steel Pipe
Activating Your Ideas In Stainless Steel Pipe Applications Outokumpu produces austenitic and duplex pipe products from small diameter pipe to large diameter, heavy wall pipe, with thicknesses up to 2 on
More informationNCCER Progress Blvd, Alachua, Florida Phone: (888)
NCCER 13614 Progress Blvd, Alachua, Florida 32615 Phone: (888) 622-3720 E-mail: info@nccer.org PIPEFITTING Competencies / Objectives Level One MODULE 08101-06 - ORIENTATION TO THE TRADE 1. Describe the
More informationFor ASME Committee use only.
ASME BPVC.III.1.NB-2015 Figure NB-4427-1 nominal pipe (c) Socket Welding Flange [Note (3)] (d) Socket Welding Fittings [Note (4)] GENERAL NOTE: See NB-3661.2 for limitation on socket weld pipe size. (1)
More informationInsertion Transducer On-line Install Instruction
LOGO Insertion Transducer On-line Install Instruction Shanghai Dynameters Co., Ltd www.dynameters.com Insertion Transducer Installation Manual Installation steps 1. Locate Installing point 2. Weld mounting
More informationPIPING NOMENCLATURE. Header Branch connection Valve Flange Expansion joint Expansion loop Pipe support Reducer Elbow
PIPING COMPONENTS Piping components are mechanical elements suitable for joining or assembly into pressure-tight fluid containing piping systems. Components include pipe, tubing, fittings, flanges, gaskets,
More information.1 Materials and installation for steel piping, valves and fittings for hydronic systems in building services piping..2 Related Sections.
Issued 2006/08/01 Section 15183 Hydronic Systems: Steel Page 1 of 6 PART 1 GENERAL 1.1 SUMMARY.1 Section Includes..1 Materials and installation for steel piping, valves and fittings for hydronic systems
More informationPipe Threads, General Purpose (Inch)
ASME B1.20.1-2013 [Revision of ASME B1.20.1-1983 (R2006)] Pipe Threads, General Purpose (Inch) AN AMERICAN NATIONAL STANDARD ASME B1.20.1-2013 [Revision of ASME B1.20.1-1983 (R2006)] Pipe Threads, General
More informationSection COUPLINGS AND COUPLING ADAPTERS. This Section covers couplings and coupling adapters for ductile iron and steel pipe.
PART 1 GENERAL 1.01 SUMMARY Section 15155 This Section covers couplings and coupling adapters for ductile iron and steel pipe. 1.02 MEASUREMENT AND PAYMENT A. No separate payment for Work performed under
More informationPIP REDP003 Documentation Requirements for High Power Centrifugal Pumps for Water Service
COMPLETE REVISION October 2013 Process Industry Practices Machinery PIP REDP003 Documentation Requirements for High Power Centrifugal Pumps for Water Service PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES
More informationAustralian Standard. Graphical symbols for general engineering. Part 3: Welding and non-destructive examination AS AS 1101.
AS 1101.3 2005 AS 1101.3 2005 Australian Standard Graphical symbols for general engineering Part 3: Welding and non-destructive examination This Australian Standard was prepared by Committee WD-001, Welding
More informationBhagwan mahavir college of Engineering & Technology, Surat.
Bhagwan mahavir college of Engineering & Technology, Surat. Department of automobile Engineering Assignment Subject: Machine Design & Industrial Drafting B.E. Second year Instructions: 1. This set of tutorial
More informationNational Craft Assessment and Certification Program S P E C I F I C A T I O N S
National Craft Assessment and Certification Program S P E C I F I C A T I O N S BOILERMAKER PRESSURE VESSEL V2 BLMK34_02 October 2014 Focus Statement A journey level boilermaker is skilled in all aspects
More informationTHERMOWELLS CONSTRUCTION FROM BARSTOCK OR FABRICATED
age 1 of 5 THERMOWELLS CONSTRUCTION FROM BARSTOCK OR FABRICATED A thermowell is a thermally conductive socket recommended to: rotect the delicate instrument sensing elements against corrosive effects.
More informationStandards Manager Web Standards List PPI-Plastic Pipe Institute
Standards Manager Web Standards List PPI-Plastic Pipe Institute Id Number Title Year Organization Page 1 TN-44 LONG TERM RESISTANCE OF AWWA C906 POLYETHYLENE (PE) PIPE TO POTABLE WATER 2015 PPI 0 DISINFECTANTS
More informationThis document is a preview generated by EVS
INTERNATIONAL STANDARD ISO 17636-1 First edition 2013-01-15 Non-destructive testing of welds Radiographic testing Part 1: X- and gamma-ray techniques with film Contrôle non destructif des assemblages soudés
More information