DIBD20, 40, 60 AND DIBD230, 430, 630 CURTAIN TYPE DYNAMIC FIRE DAMPERS
|
|
- Bennett Kennedy
- 5 years ago
- Views:
Transcription
1 00 Dr. Greaves Rd. Kansas City, MO 00 (1) 1- F (1) - DID, 0, 0 ND DID0, 0, 0 CURTIN TYPE DYNMIC FIRE DMPERS 1 1 / ND OUR UL RTED FOR USE IN DYNMIC ND STTIC SYSTEMS PPLICTION DID, 0, 0 fire dampers can be installed vertically in walls or horizontally in floors with fire resistance ratings of less than hours. The DID, 0, 0 carry a 1 1 / hour UL fire damper label and are classified as a dynamic damper for use in VC systems that remain in operation during a fire. DID0, 0, 0 can be installed vertically in walls or horizontally in floors with fire resistance ratings of hours or more. The DID0, 0, 0 carry a hour UL fire damper label and are classified as a dynamic damper for use in VC systems that remain in operation during a fire. DYNMIC CLOSURE RTINGS 000 fpm (. m/s) vertical mount only, up to x ( x ). 000 fpm (. m/s) vertical and horizontal mount, up to x ( x ). 00 fpm (. m/s) vertical or horizontal mount on all sizes. in. w.g. (1kPa) maximum pressure on all sizes. STNDRD CONSTRUCTION FRME ND LDES MTERIL Galvanized steel (in gauges required by UL listing R-1). FRME/SLEEVE LENGT DID, DID0 - " long DID0, DID0 - " () long DID0, DID0-1" (0) long CLOSURE SPRINGS 01 stainless steel constant force or spring clip type. FUSILE LINK F ( C) is standard. F (0 C) and F (1 C) are available. DMPER SIZES The sizes listed below are for Style dampers. Refer to pages and for sizes of other style dampers. Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) for dampers no larger than w or h ( or ). Dampers larger than w or h ( or ) have a minimum size of w or h ( or ). Single Section Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) Multiple Section Vertical Installation "w x "h ( x 1), "w x "h (1 x ) or "w x "h ( x ) orizontal Installation "w x "h ( x 1) OPTIONS FM pprovals as Specification Tested Product. Switch Package to remotely indicate damper blade position. FST ngle for one side angle installation DID for easy all from one side installation. G Style for grille applications. FireStop Caulk Installation. NOTE: 1.. Damper Sleeves ma need to be sealed in the field to pass local duct leakage requirements. Models DID, 0, 0 and DID0, 0, 0 meet the requirements for fire, dampers established by: National Fire Protection ssociation NFP Stand ards 0 and 1 ICC International uilding Codes CSFM California State Fire Marshal Fire Damper Listing (#-:00) New York City (S Listing #-1-S) DID only. UL CLSSIFIED UL Listing R1 SEE COMPLETE MRKING ON PRODUCT VERTICL MOUNT L = Frame/Sleeve Length FM pprovals Specification Tested Product (Option) ORIZONTL MOUNT Spec DID, 0, 0, 0, 0, 0-1/ Replaces DID, 0, 0, 0, 0, 0-1 LL STTED SPECIFICTIONS RE SUJECT TO CNGE WITOUT NOTICE OR OLIGTION. Ruskin November 1
2 DMPER STYLES ND SIZES Style lades out of airstream for high free area applications Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) for dampers no larger than "w or "h ( or ). Dampers larger than w or h ( or ) have a minimum size of w or h ( or ) Single Section Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) Multiple Section Vertical Installation "w x "h ( x ), "x "h (1 x ) or "w x "h( x ) orizontal Installation "w x "h ( x ) = Duct Width = Duct eight = Overall Damper eight C and LC Style Sealed (C) or non-sealed (LC) square or rectangular transition for maximum free area applications Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) Single Section Vertical Installation 1"w x 1"h ( x ) orizontal Installation "w x "h ( x 0) + ( + 1) = Duct Width = Duct eight = Overall Damper eight CR Style Sealed round transition for 0% free area applications Vertical Installation " () diameter orizontal Installation " () diameter Vertical Installation Single Section 1" () diameter orizontal Installation Single Section " (0) diameter D + " (D + 1) Dia. D = Diameter = Overall Damper eight
3 DMPER STYLES ND SIZES CO Style Sealed oval transition for 0% free area applications Vertical Installation "w x "h ( x ) orizontal Installation "w x "h ( x ) Vertical Installation Single Section 1"w x 1"h ( x ) orizontal Installation Single Section "w x "h ( x 0) Multiple Sections "w x "h ( x ) + " + = Duct Width = Duct eight = Overall Damper eight LO, LR and R Style Non-sealed oval (LO) or round (LR, R) transitions for low pressure applications. LO and LR transitions offset for 0% free area applications. R transition centered for use when 0% free area not required. Vertical Installation LR, R Styles " () diameter LO Style "w x "h ( x ) orizontal Installation LR, R Styles " () diameter LO Style "w x "h ( x ) Vertical Installation LR, R Styles 1" ( ) diameter LO Style 1"w x 1"h ( x ) orizontal Installation LR, R Styles " (0) diameter LO Style "w x "h ( x 0) STYLE LO + " + STYLE LR D STYLE R D + " D + D + " D + D + " D + D = Duct Width = Duct eight = Overall Damper eight D = Diameter
4 SSEMLY ND DIMENSIONL INFORMTION Dampers normally fabricated approximately 1 /" () less than given duct dimensions. (width) and (height) dimensions shown describe maximum UL Classified sizes. Ruskin recommends the authority having jurisdiction, the engineer and the contractor agree on the installation design prior to installation. DID, 0, 0, 0, 0, 0 multiple section dampers are shipped in individual sections, for field assembly. If TDF or other flanged breakaway connections are to be used, order dampers with factory furnished sleeves actual size. STYLE DMPERS VERTICL INSTLLTION Important Note: Dampers larger than " x " ( x ) are multiple section dampers consisting of equal sections no larger than " x " ( x ). Multiple Section Dampers x x " () x x x " (1) x " () x x 0 () " () 0" (0) " (1) " () (1) () () () () (1) (0) () () (0) () () () (0) () () () () () () () () () () lade Dimensions / / / / / / / / / / / / 1 / 1 / 1 / 1 / 1 / 1 / 1 / 1 / 1 / 1 / / / / / () () () () () (0) (0) () () () (0) (0) () () () () () () () () () () () () () () () () () ORIZONTL INSTLLTION Important Note: Dampers larger than " x " ( x ) are multiple section dampers consisting of equal sections no larger than " x " ( x ). Multiple Section Dampers lade p p Dimensions ) 1" () " (1) " (1) () (1) () () () () (1) (0) () () (0) () () 1 1 / 1 1 / / 1 / / / / / / / / / () () () () () (0) (0) (0) () () (0) (0) () () () Important Notes: 1. Dampers larger than " x " ( x ) are multiple section dampers consisting of equal sections no larger than 1" x " ( x ).. Dampers larger than "w or "h ( x ) have a minimum size of "w or "h ( x ).
5 STYLE DMPERS VERTICL INSTLLTION Multiple Section Dampers x " () " () () () () (1) () () () () (1) (0) () () (0) () () () (0) () () () () () () / / / / / / / / / / 1 / 1 / 1 / / / / / / / / / / / 0 / 1 / / / / / () () (1) () () () () () () (00) () () () () () (0) (0) () () (0) (0) () (1) (0) () () () (0) For dampers larger than W / / 1 / / / / () () (0) () () () " () " () 0" (0) " (1) " " () () " Important Note: Dampers larger than " x " ( x ) are multiple section dampers consisting of equal sections no larger than " x " ( x ) overall. To determine the overall height ( dimension) of double high and triple high damper assemblies: dd /" (0) to the dimension. For example, a " double high assembly is /" () overall height. " (1) triple high assembly is /" (1) overall height. The bottom sections on double and triple high assemblies are Style dampers. () ORIZONTL INSTLLTION Multiple Section Dampers " () () () (1) () () () () (1) (0) () () (0) / / / / / / / / / / 1 / 1 / 1 / 1 / / / / / () () (1) () () () () () () (00) () () (0) () () () (0) 1" () Max " () " () Important Notes: 1. Dampers larger than " x " ( x ) are multiple section dampers consisting of equal sections no larger than 1" x " ( x ) overall.. Dampers larger than "w or "h ( x ) have a minimum size of "w or "h ( x ). To determine the overall height ( dimension) of double high damper assemblies: dd 1 /" () to dimension on dampers over " through and 1 /" (0) on all other dampers. For example, a damper with a " () dimension has an overall dimension of 1 /". "
6 C, CO, LO ND LC STYLE DMPERS VERTICL INSTLLTION ORIZONTL INSTLLTION 1" () 1" () 1" () () () () () (1) () () () () (1) (0) () () (0) () () () (0) () () () () () / / / / / / / / / / 1 / 1 / 1 / / / / / / / / / / / 0 / 1 / / / / / () () (1) () () () () () () (00) () () () () () (0) (0) () () (0) (0) () (1) (0) () () () (0) + " ( + 1) " () 1" () " (0) () () () () (1) () () () () (1) (0) () () (0) / / / / / / / / / / 1 / 1 / 1 / 1 / / / / / () () (1) () () () () () () (00) () () (0) () () () (0) CR ND LR STYLE DMPERS VERTICL INSTLLTION ORIZONTL INSTLLTION D 1" () () () () () (1) () () () () (1) (0) () () (0) () () () (0) () () () () () / / / / / / / / / / 1 / 1 / 1 / / / / / / / / / / / 0 / 1 / / / / / () () (1) () () () () () () (00) () () () () () (0) (0) () () (0) (0) () (1) (0) () () () (0) D " () () () () (1) () () () () (1) (0) () () (0) / / / / / / / / / / 1 / 1 / 1 / 1 / / / / / () () (1) () () () () () () (00) () () (0) () () () (0)
7 LOR SVER CCESSORY OPTIONS TDF OR DUCTMTE REKWY CONNECTIONS Meet UL breakaway connection requirements without changing connectors. Ruskin fire dampers can be installed using non-matched flange connections for the breakaway requirement. ny flange connection can mate to a different type or model on Ruskin fire dampers. FST MOUNTING NGLES FST mounting angles are used in lieu of conventional, eight piece mounting angles and are installed on only one side of the wall when used with Ruskin DID fire dampers. The FST angle can be fastened directly to the metal stud underneath the fire rated gypsum wallboard. SP0 SWITC PCKGE OPTION The SP0 switch package on curtain fire dampers (ID s and DID s), used in conjunction with the MCP (Single Control Station with Open/Closed Lights) provides the ability to remotely identify PPLICTION the damper s blade position. Electrical interface with remote control on/off fan stations is also possible with the SP0. (D)ID Damper x andy ox SP-0 Standard Mounting Detail
8 VOC Content (g/l) - 0 Manufacturing Locations (MR Credit.1) Mira Loma, C Parsons, KS Lexington, KY 00 Fairmont, WV LEED 0 Information Recycled Content (MR Credit.1 &.).% Post Consumer.% Pre-Consumer Post Industrial pproximate Damper ssembly Weight DID and 0 lbs. per sq. ft. DID0 and 0 lbs. per sq. ft. DID0 and 0 lbs. per sq. ft. SUGGESTED SPECIFICTION FOR DID, 0, 0 Furnish and install, at locations shown on the plans, dynamic fire dampers tested, constructed and labeled in accordance with the latest edition of UL Standard. Dampers shall have a fire rating of / hours and shall meet the requirements of the latest edition of NFP0. Each damper shall include a F ( C) or F (0 C) fusible link (specifier select) and shall be labeled for use in dynamic systems. Dampers labeled for use in static systems only are not permitted. The damper shall be rated for dynamic closure to a minimum 00 fpm (.1 m/s) and inches w.g. (1 kpa) static pressure and shall be rated to close with airflow in either direction. Each dynamic fire damper shall include a ", " or 1" (0, or 0) (specifier select) long integral roll formed steel sleeve and mounting angles furnished by the damper manufacturer to ensure appropriate installation. Submittal information shall include the fire protection rating, maximum velocity/pressure ratings and the manufacturer's UL installation instructions. The dampers shall be installed in accordance with the manufacturer s UL installation instructions. Dynamic fire dampers shall be curtain type Ruskin model DID with " sleeve, DD0 with " () sleeve or DID0 with 1" (0) sleeve (specifier select). SUGGESTED SPECIFICTION FOR DID0, 0, 0 Furnish and install, at locations shown on the plans, dynamic fire dampers tested, constructed and labeled in accordance with the latest edition of UL Standard. Dampers shall have a fire rating of hours and shall meet the requirements of the latest edition of NFP0. Each damper shall include a F ( C) or F (0 C) fusible link (specifier select) and shall be labeled for use in dynamic systems. Dampers labeled for use in static systems only are not permitted. The damper shall be rated for dynamic closure to a minimum 00 fpm (.1 m/s) and inches w.g. (1 kpa) static pressure and shall be rated to close with airflow in either direction. Each dynamic fire damper shall include a ", " or 1" (0, or 0) (specifier select) long integral roll formed steel sleeve and mounting angles furnished by the damper manufacturer to ensure appropriate installation. Submittal information shall include the fire protection rating, maximum velocity/pressure ratings and the manufacturer's UL installation instructions. The dampers shall be installed in accordance with the manufacturer s UL installation instructions. Dynamic fire dampers shall be curtain type Ruskin model DID0 with " sleeve, DD0 with " () sleeve or DID0 with 1" (0) sleeve. 00 Dr. Greaves Rd. Kansas City, MO 00 (1) 1- F (1) -
DIBD2 and DIBD23 CURTAIN TYPE DYNAMIC FIRE DAMPERS 1 1 /2 AND 3 HOUR UL555 RATED FOR USE IN DYNAMIC AND STATIC SYSTEMS
00 r. Greaves Rd. Kansas City, MO 00 (1) 1- F (1) - I and I CURTIN TYPE YNMIC FIRE MPERS 1 1 / N OUR UL RTE FOR USE IN YNMIC N STTIC SYSTEMS PPLICTION I fire dampers can be installed vertically in walls
More informationHALDEMAN, INC. BRAND: RUSKIN. Fire Dampers. IBD20 Deduct 1/4 Inch. Model:
LEMN, INC. REPS v.. RN: RUSKIN Fire ampers Model: FRME: MOUNTING: FUSELINK TEMP: SLEEVE/TRNS: SLEEVE LENGT: SLEEVE GUGE: SLV MTERIL: MOUNTING NGLES: NGLE IM/G: I0 educt / Inch STYLE VERTICL EGREES SLEEVE
More informationIBD23 CURTAIN TYPE STATIC FIRE DAMPERS 3 HOUR UL555 RATED FOR USE IN STATIC SYSTEMS
3900 Dr. Greaves Rd. Kansas City, MO 64030 (816) 761-7476 FX (816) 765-8955 ID23 CURTIN TYPE STTIC FIRE DMPERS 3 OUR UL555 RTED FOR USE IN STTIC SYSTEMS pplication Ruskin Model ID23 3 hour UL classified
More informationModel ABV Pressure Independent Automatic Balancing Valve. Application: Standard Construction: Performance: Configurations Available:
Application: Tag: Project: Location: Date: Engineer: Contractor: Architect: Submitted by: The ABV Automatic maintains a constant airflow volume in HVAC applications. The highly engineered damper blade
More informationPRESTON HEALTH SERVICES ARCHITECT S NO. 2700
SECTION 23 3113 - LOW PRESSURE DUCTWORK PART 1 - GENERAL 1.1 SCOPE OF WORK: A. The work required under this section includes all work necessary for a complete installation of ductwork and accessories.
More informationSECTION LOW PRESSURE DUCTWORK
SECTION 15841 LOW PRESSURE DUCTWORK PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 07270 - Firestopping and Fire and Smoke Barrier Caulking. 2. 15260 - Vibration Isolation. 3. 15280 - Thermal Insulation
More informationLOW PRESSURE STEEL DUCTWORK Mechanical Systems Insulation Outlets (HVAC) Testing and Balancing.
SECTION 15841 LOW PRESSURE STEEL DUCTWORK PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15180 - Mechanical Systems Insulation. 2. 15940 - Outlets (HVAC). 3. 15991 - Testing and Balancing. 1.02 SUBMITTALS
More informationDocument Number ODFD-XXX and OFD-XXX Series Installation Drawings for Out of Wall Curtain Fire Dampers
Document Number 481329 ODFD-XXX and OFD-XXX Series Installation Drawings for Out of Wall Curtain Fire s Approved installations for curtain fire dampers 1) Through the grille access and 2) Installation
More information*************************************************************************************************************
15890 DUCTWORK ************************************************************************************************************* SPECIFIER: CSI MasterFormat 2004 number: 23 33 13 *************************************************************************************************************
More informationA. Radius elbows with a construction radius of 1.5 the duct width are preferred to square elbows.
SECTION 233100 DUCTWORK 1.0 Acoustical duct lining in any part of the duct system is prohibited. All ductwork requiring insulation shall be externally insulated (Refer to the Sheet Metal Ductwork Insulation
More informationLINEAR DIFFUSERS AND BAR GRILLES
Model 49-240 Model 48LL1 Model 49-280 Model 49-480 Model 48LL2 Linear ar Grilles The Nailor 4900 Series provides an extruded aluminum bar grille that offers beautiful styling and efficient performance.
More informationDuctwork Controls and Instrumentation Outlets (HVAC) HVAC Control System.
SECTION 15910 DUCT ACCESSORIES PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15890 - Ductwork. 2. 15900 - Controls and Instrumentation. 3. 15940 - Outlets (HVAC). 4. 15970 - HVAC Control System.
More informationFLOWLINE LINEAR DIFFUSERS
FLOWLINE LINER DIFFUSERS 1 FLOWLINE LINER DIFFUSERS Contents Overview of FlowLine System Continuous FlowLine Linear FL Series orizontal igh Throw Pattern Controllers FLV Series Vertical Jet Throw Pattern
More informationSt. Monica Food Pantry
St. Monica Food Pantry 23 3300-1 HVAC WORK DIVISION 23 SECTION 233300 HVAC AIR DUCT ACCESSORIES PART 1. GENERAL 1.1 WORK INCLUDES A. Gravity Operated Backdraft Dampers B. Volume dampers C. Motor operated
More informationModel LF2500 Low Frequency Sound Silencer
Model LF Low Frequency Sound Silencer The SEMCO Model LF low frequency sound silencers are specifically designed to solve noise problems in the lower frequency range and will provide excellent low band
More informationPart No. Thread Size B Design Load Approx. Wt./100 A in. (mm) Lbs. (kn) Lbs. (kg)
ttachments Fig. 3199R - eiling Flange Fig. 3199RT - eiling Flange ura-opper oated Size Range: 3 /8"-16 & 1 /2"-13 rod Material: Malleable Iron (Stainless Steel Type 304 available) Standard 3199RT is UR-OPPER
More informationGRILLE AND REGISTER OPTIONS AND ACCESSORIES
GRILLE ND REGISTER OPTIONS ND CCESSORIES PRODUCT OVERVIEW OPTIONS ND CCESSORIES FOR FSTENING ND MOUNTING FRMES Up to four methods of fastening available for most models. Sub-frame available for professionally
More informationMax. Rec. Load. Wt. Per Inch lbs. kn lbs. kn lbs. kg. Wt. Per Inch lbs. kn lbs. kn lbs. kg 750 F (399 C)
FIG. 10 FIG. 15 & 15L Function: Designed for use in pipe hanger assemblies. (Type 304 or 316 Stainless Steel upon request) Ordering: Specify figure number, rod size, length (), material, and finish. 650
More informationB3199R - Ceiling Flange B3199RCT - Ceiling Flange Dura-Copper Coated. TOLCO Fig All Steel Ceiling Plate. 216 Eaton
ttachments 3199R - eiling Flange 3199RT - eiling Flange ura-opper oated Size Range: 3 /8"-16 & 1 /2"-13 rod Material: Malleable Iron (Stainless Steel Type 304 available) Standard 3199RT is UR-OPPER coated
More informationInstallation and Maintenance Manual
Installation and Maintenance Manual IM770 Group: pplied ir Part Number: IM770 Date: pril 2003 Roof Curb for Skyline TM Outdoor ir Handlers 2013 Daikin pplied IM 770 Page 1 Table of Contents General Description...
More informationSubmittal Sheet COUNTERSUNK HOLES SDG SPIRAL DUCT GRILLE 1 7/8" (47) + 1 1/4" (32) - 3/4" (19) ( DUCT OPENING ) END GASKET NOM. LENGTH - 3/4" (19) OPTIONAL AIR SCOOP AIR SCOOP (ROD OPERATOR) NOM. LENGTH
More informationTechnical Development Program
Technical Development Program COMMERCIAL DISTRIBUTION SYSTEMS PRESENTED BY: Ray Chow Duct Design Level 1 Fundamentals Sales Engineer Menu Section 1 Section 2 Section 3 Section 4 Section 5 Introduction
More informationCHAPTER 6 DUCT SYSTEMS
CHAPTER 6 DUCT SYSTEMS 601.0 Scope General. 601.1 General Applicability. Ducts and plenums that are portions of a heating, cooling, absorption or evaporative cooling, or product-conveying system shall
More informationThe General Provisions of the Contract, including General, Supplementary and Special Conditions, apply to the work specified in this Section.
SECTION 23 31 13 METAL HVAC DUCTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS The General Provisions of the Contract, including General, Supplementary and Special Conditions, apply to the work specified in
More information1.04 QUALITY ASSURANCE
SECTION 07312 ARCHITECTURAL ASPHALT SHINGLES PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationMP918B UL Listed Damper Actuator
UL Listed Damper Actuator BEFORE INSTALLATION The UL Listed Pneumatic Damper Actuator is used for control of Leakage Rated (Smoke) Dampers, classified under Underwriters Laboratories (UL) Standard 555S,
More informationM1.0 MECHNANICAL FLOOR PLAN
GENERAL NOTES A. CONTRACTORS AND SUB CONTRACTORS SHALL CAREFULLY REVIEW THE CONSTRUCTION DOCUMENTS. INFORMATION REGARDING THE COMPLETE WORK IS DISPERSED THROUGHOUT THE DOCUMENT SET AND CANNOT BE ACCURATELY
More informationMATERIAL COMBINATION NUMBER 2: Corrosive environment requiring harder, wear-resistant seating faces and resistance to dezincification.
Cast Iron Slide Gates Spec Sheet General The contractor shall furnish and install the following cast iron slide gate assemblies as listed on the Gate Schedule and detailed on the manufacturer s drawings.
More information25 / 35 / 45. Rectangular Duct Connection System. Strong and Virtually Leak Free. Simple to install No additional sealing required
D U C T M A T E 25 / 35 / 45 Rectangular Duct Connection System Strong and Virtually Leak Free Simple to install No additional sealing required Available in specialty metals Consistent connections 25 /
More information300 Series Pin & Barrel Type Continuous Stainless Steel Hinges
www.mfsales.com 300 Series Pin & Barrel Type Continuous Stainless Steel Hinges Short Form Architectural Specification: Continuous hinges shall be full height piano-type hinge providing full height door
More informationSECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationBXUV.V470. Fire Resistance Ratings - ANSI/UL 263. Design/System/Construction/Assembly Usage Disclaimer. Fire Resistance Ratings - ANSI/UL 263
Page Bottom BXUV.V470 Fire Resistance Ratings - ANSI/UL 263 Design/System/Construction/Assembly Usage Disclaimer Authorities Having Jurisdiction should be consulted in all cases as to the particular requirements
More informationAPPENDIX A, UMC STANDARD 6-5 STANDARD FOR INSTALLATION OF FACTORY-MADE AIR DUCTS
STANDARD FOR INSTALLATION OF FACTORY-MADE AIR DUCTS Sealing of fibrous glass duct board to the sheet metal sleeve must be made with glass fabric and mastic, except where operating pressure is less than
More informationRemoteTeller SYSTEM - RTS VAT 21 GX CUSTOMER UNIT COMPONENTS CUSTOM DESIGNED CUSTOMER AREA
SEND SEND CLL CLL L " LCD COLOR MONITOR 4-29- COLOR CCD CMER 4-29- 486G VT 2 GX CUSTOMER UNIT CLL -8-999-6 LISTINGS ND PPROVLS CLSSIFIED TO UL 4R SFETY OF INFORMTION TECHNOLOGY EQUIPMENT UL TESTED TO THE
More informationRound Duct and Fittings. Standards and Dimensional Data for Air Duct and Fittings
Round Duct and Fittings Standards and Dimensional Data for Air Duct and Fittings www.airsidesheetmetal.com 973-786-6967(office) 973-786-6474(fax) Fabricated by Airside Sheet Metal Fabricators, Inc. - 2017
More informationSUBMITTAL SHEET. Project Submittals by
Galvanized Tie Wire and Hanger Wire Submittal of Product Performance SUBMITTAL SHEET Project Submittals by GRABBER CONSTRUCTION PRODUCTS, INC. Submittal Date: Contract Number: Project Name: Section Number:
More informationINSTALLATION INSTRUCTIONS FOR CECO DOOR FLOOD RESISTANT DOOR AND FRAME ASSEMBLIES
INSTLLTION INSTRUCTIONS FOR CECO DOOR FLOOD RESISTNT DOOR ND FRME SSEMBLIES GENERL The installation of flood resistant door and frame assemblies differs significantly from that of standard door and frame
More informationTechnical Data VARIABLES
Overview SYSTEM Rulon Panel Grilles are manufactured with aligned and spaced wood strips suspended vertically or horizontally, giving a ladder-like appearance. Panel Grilles provide a modern or traditional
More informationSECTION CABLE TRAYS
SECTION 16139 CABLE TRAYS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationSECTION AIR DISTRIBUTION SYSTEM
SECTION 23 30 00 AIR DISTRIBUTION SYSTEM PART 1 - GENERAL 1.1 Scope of Work: The work covered by this section consists of providing all labor, equipment and materials and performing all operations necessary
More informationEBTRON a measurable difference!
GP1, HP1 AND SP1 DUCT AND PLENUM PROBE INSERTION MOUNT INSTALLATION Document Number 930-0030 OVERVIEW This document provides the instructions necessary to install Standard insertion mount probes as shown
More informationREVISION #1. Section. fire alarm B. C. the hot. intent of. required. manufacturer. materials. C. Warranty
HOT AISLE CONTAINMENT SYSTEM (HACS) REVISION #1 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. B. C. Drawings and general provisions of the Contract, including General and Supplementary. Conditions apply to
More informationFIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS
FIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS These requirements apply to all fire rated doors, frames, and windows. Requirements for the installation of these assemblies are included in the Standard
More information5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More informationLABEL & RATING OPTIONS
LABEL & RATING OPTIONS FIRE LABELING GUIDELINES APPLICATION MAXIMUM SIZE HOURLY RATING Single Door 4'0" wide x 10'0" high Up to 3 hour 4'3" wide x 10'0" high Up to 1-1/2 hour Pair 8'0" wide x 10'0" high
More informationFIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS
` FIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS These requirements apply to all fire rated doors, frames, and windows. Requirements for the installation of these assemblies are included in the Standard
More informationHVAC Spiral Pipe Component Parts
VC piral Pipe Component Parts Yellow label union manufacturer of VC piral Pipe component parts tamped Fittings VC component parts will save you time and money on your next spiral pipe job. In a market
More informationGE Monogram 36" Built-In Bottom-freezer Refrigerator
SECTION 1 FLUSH INSET INSTLLTION SECTION 2 STNDRD INSTLLTION 1/4" FRMED PNELS 3/4" OVERLY PNELS OVERLL DIMENSIONS FLUSH INSET INSTLLTION 38" (96.5) 25 7/8" (65.7) 20 5/8" (52.4) 9 5/8" (24.4) * 8 (212.1)
More informationContemporary Collection
HZ4STE Gas Fireplace Model HZ4STE - NG1 HZ4STE-LP1 Fuel Type Natural Gas Propane Gas Minimum Supply Pressure 5 W.C.(1.5 kpa) 1 W.C. (.98 kpa) Manifold Pressure - High 3.5 W.C. (.87 kpa) 1 W.C. (.49 kpa)
More informationEBTRON a measurable difference!
GP1, HP1 AND SP1 DUCT AND PLENUM PROBE INTERNAL MOUNT INSTALLATION OVERVIEW This document provides the instructions necessary to install Internal Mount Probes as shown in Figure 1. Internally mounted probes
More informationRegency Bellavista B41XT-1 Gas Fireplace
Regency ellavista 1XT-1 Gas Fireplace Specifications: Model 1XT-NG 1XT-LP Fuel Type Natural Gas Propane Gas Minimum Supply Pressure Manifold Pressure - High Manifold Pressure - Low 5 W.C. (1.5 kpa) 3.5
More informationCOMMERCIAL KITCHEN HOOD WORKSHEET/ CHECKLIST
COMMERCIAL KITCHEN HOOD WORKSHEET/ CHECKLIST Two copies of this worksheet/checklist must accompany plans sets submitted with commercial kitchen application. The applicant is responsible for assuring the
More informationCSP PSYCHIATRIC SERVICES UNIT SECTION IDENTIFICATION FOR HVAC PIPING AND EQUIPMENT
SECTION 23 05 53 IDENTIFICATION FOR HVAC PIPING AND EQUIPMENT PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pipe Markers. 2. Valve Tags. 3. Equipment Nameplates. 4. Underground Marking Tape. 5. Duct
More informationSECTION WOOD SHINGLES
SECTION 07 31 29.13 WOOD SHINGLES SPEC WRITER NOTES: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. This guide specification does not include requirements
More informationINS A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE. 1. Unpacking the KSCR Splicing the KSCR (If Required)...
INS-88.500-0A KSCR INSTALLATION INSTRUCTIONS STANDARD PROCEDURE 1. Unpacking the KSCR... 2 2. Splicing the KSCR (If Required)... 4 3. Assemble Curb and Rail Corners... 5 4. Install Cross Bracing (If Required)...
More informationInstallation Guide 888-4WB TRAY
Installation Guide WBT has pioneered the innovation of cabletray/basket tray in the last decade. Products such as Shaped Tray, PreForm, WBTForm and NoSplice have allowed users and installers to provide
More informationEMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL
EMMEGI ARCHITECTURAL FENCING MASTER SPECIFICATION SECTION 05720 METAL FENCING, GATES & RAILING SYSTEM PART 1 GENERAL EMMEGI ARCHITECTURAL FENCING is a high quality steel fencing system comprised of a hybrid
More informationHALLOWELL HI-TECH SHELVING
LLOLL I-C SLVING i-ech Industrial grade steel shelving continues a tradition of quality established generations ago with the goal of providing a shelving line with the strength needed to handle most industrial
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationVersatrac R-System Stock Extrusions, Clips and Accessories
Versatrac R-System Extrusions are available in 300 series (for 3 3/4" walls) and 400 series (for 4 7/8" walls). Standard finishes are Satin Metallic Bronze, Satin Black, Satin White Baked Enamel, and Clear
More informationFlushglaze For Framed Openings and Horizontal Panels. Window System Installation Guide
Flushglaze 4500 For Framed Openings and Horizontal Panels Window System Installation Guide January 2017 BENCHMRK Welcome to Kingspan, global leaders in the design and manufacture of insulated metal panels
More informationThe General Provisions of the Contract, including General, Supplementary and Special Conditions, apply to the work specified in this Section.
SECTION 15800! AIR DISTRIBUTION PART 1! GENERAL 1.01 RELATED DOCUMENTS The General Provisions of the Contract, including General, Supplementary and Special Conditions, apply to the work specified in this
More informationSECTION WIREWAYS FOR RADIOLOGY EQUIPMENT
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 05 36 WIREWAYS FOR RADIOLOGY EQUIPMENT SPEC WRITER NOTE: Delete between //----// if not applicable to project. Also, delete any other item or paragraph not applicable
More informationVersatrac R-System Stock Extrusions, Clips and Accessories
Versatrac R-System Extrusions are available in 300 series (for 3 3/4" walls) and 400 series (for 4 7/8" walls). Standard finishes are Satin Metallic Bronze, Satin Black, Satin White Baked Enamel, and Clear
More informationGE Monogram. Installation. Instructions. 36" Vent Hood. Model ZV750. Call anywhere in the US and Canada -
at :: rangehoods. com GE Monogram Instructions Model ZV750 GE Monogram at:: rangehoods. com is a division of CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:
More informationWAL-MART SUPERCENTER # ; Milwaukie, OR: SPECIFICATIONS. Revisions to Specification Fence
MILWAUKIE OR #3144-00 ADDENDUM #5 NARRATIVE: 11-08-12 WAL-MART SUPERCENTER #3144-00; Milwaukie, OR: SPECIFICATIONS SPECIFICATIONS Revisions to Specification 02822 Fence Spec division 02822 has been revised
More informationInstallation Instructions. 45 and 60-Minute Positive Pressure Fire-Rated Veneered Door Frame UBC & UL-10C
Wood Doors Installation Instructions 45 and 60-Minute Positive Pressure Fire-Rated Veneered Door Frame UBC 7-2-1997 & UL-10C Positive Pressure Category Requirements: Category C The Maiman Company Fire
More informationRigid Line Components and Accessories
Rigid Line Components and ccessories Rigid Coaxial Line System Components and Installation ccessories enefits Superior engineering for excellent performance Superior materials for high durability merican
More informationLightplane 3.5 Recessed
INSTALLATION INSTRUCTIONS Lightplane 3.5 Recessed LP3.5R Recessed Ceiling IMPORTANT SAFETY INSTRUCTIONS When installing or using this fixtures basic safety precautions must be followed. Read all instructions
More informationContemporary Collection
HZ5E Gas Fireplace Model HZ5E-NG1 HZ5E-LP1 Fuel Type Natural Gas Propane Gas Minimum Supply Pressure 5 W.C.(1.5 kpa) 1 W.C. (.98 kpa) Manifold Pressure - High 3.5 W.C. (.87 kpa) 1 W.C. (.9 kpa) Manifold
More informationSECTION WOOD AND PLASTIC DOORS. A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION.
SECTION 081416 PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. PART A and DIVISION 1 of PART B are hereby made a part of this SECTION. B. Examine all conditions as they exist at the project prior to submitting
More information2. All work and materials shall be in full accordance with Local and State ordinance and with any prevailing rules and regulations.
General Conditions: 1. Deliver all food service equipment as specified herein, including that which is reasonably inferred, with all related items necessary to complete work shown on contract drawings
More informationESR-1254 * DELETED BY CITY OF LOS ANGELES. Reissued April 1, 2006 This report is subject to re-examination in one year.
ESR-1254 Reissued April 1, 2006 This report is subject to re-examination in one year. www.icc-es.org Business/Regional Office 5360 Workman Mill Road, Whittier, California 90601 (562) 699-0543 Regional
More informationINSTALLATION & OPERATION MANUAL ML-37 / ML-38 / ML-39 MLR-37 / MLR-38 / MLR-39. Redefine your comfort zone.
INTALLATION & OPERATION MANUAL ML-37 / ML-38 / ML-39 MLR-37 / MLR-38 / MLR-39 IOM Linear lot Ceiling Diffusers Factory Cut upply ML-37 ML-38 ML-39 Factory Cut Return MLR-37 MLR-38 MLR-39 Factory pacer
More informationRound/Octagon Boxes and Accessories
Round/Octagon Boxes and Accessories 4" Round Boxes DEPTH BOTTOM CAT. NO. (IN.) CAPACITY DESCRIPTION CONDUIT CTN. 56111 1 2 6.0 Steel outlet box 4 1 2 50 56111-CFB* 1 2 6.0 Ceiling fan box with plastic
More informationProduct Evaluation Report
Product Evaluation Report PER0601 Page 1 of 6 Initial Listing September, 06 This Document Published By: ReApproved April, 08 Listed Product VersaPin Gripshank Pneumatic Fastener Listed For Aerosmith Fastening
More informationInstallation Guide. Overview
Installation Guide Thank you for selecting a DuctSox SkeleCore Pull-Tight with Track System. This guide will be helpful for installing the system. The key to a successful SkeleCore Pull-Tight installation
More informationSquare Straight Steel - 4 Bolt Base Light Poles
Quick Ship Square Bronze over Galvanized Straight Steel Pole - 4 Bolt Base Square Straight Steel - 4 Bolt Base Light Poles Optional Tenon Mounting (specify) "D" Top Diameter Arm Drilling Per Customer Specs.
More informationModel 30/L/0. Model 30/S/0. Shortl Blades, 0 Deflection 3/4" Spacing. Model 35/S/0 Short Blades, 0 Deflection 1/2" Spacing
model 30 / 35 - Steel Return Grilles & Registers 0 Deflection 0 fixed blade deflection maximizes free area for low pressure loss and sound levels Potential line of sight into duct thru grille is acceptable
More informationSTEEL C-CLAMP WITH LOCKNUT
FIG. 250 STEEL C-CLAMP WITH LOCKNUT Function: Designed for attaching hanger rod to the bottom flange of a beam. The hanger rod should make contact with the beam flange to ensure full engagement. Material:
More informationSECTION SWINGING AUTOMATIC ENTRANCES IN-GROUND, AUTOMATIC SWING DOOR OPERATOR CONVERTER ADAPTED TO BROOKFIELD NB-500 EXTREME DUTY OPERATOR
SECTION 084229.33 SWINGING AUTOMATIC ENTRANCES IN-GROUND, AUTOMATIC SWING DOOR OPERATOR CONVERTER ADAPTED TO BROOKFIELD NB-500 EXTREME DUTY OPERATOR PART 1-GENERAL 1.01 DESCRIPTION A. This section describes
More informationNON-PENETRATING ROOFTOP HANGERS AND SUPPORTS
SECTION 15062 NON-PENETRATING ROOFTOP HANGERS AND SUPPORTS For best results, display hidden notes to specifier. PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe supports. B. Conduit supports. C. Duct supports,
More informationIF THIS SHEET IS NOT FILLED OUT, SIGNED AND RETURNED, PRODUCTION WILL BE POSTPONED UNTIL THIS DOCUMENT IS COMPLETED AND RETURNED.
X 2/18/2015 JDF Trash Chute & Trash Compactor P.O. Box 405 939 West Quincy St. Lakeland, FL 33802/33815 Phone: 800-659-1797 Fax: 863-683-9749 www.linenchutes.com Valiant Products, Inc. Trash/Linen Chutes
More informationB. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.
SECTION 081113 - HOLLOW METAL DOORS AND FRAMES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Standard hollow metal doors and frames. 1.2 SUBMITTALS A. Product Data: For each type of product indicated.
More informationMR Modulo Adjustable Constant Airflow Regulator
& ZONE CONTROLS Adjustable Constant Airflow Regulator PRODUCT SPECIFICATIONS & TECHNICAL DATA Construction 5 4 1 GENERAL The model Adjustable Constant Airflow Regulator is a modulating orifice that automatically
More information4. Metal roof jacks at penetrations and attachments
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - SECTION 07 61 00 METAL SHINGLE ROOFING - - - - - - - - - - -
More informationTECH BULLETIN SIP No Subject: Fire Resistive Assemblies Date: November 2007 (Revised May 2017) Roof/Ceiling: 1-Hour Rating
TECH BULLETIN SIP No. 2018 Subject: Fire Resistive Assemblies Date: November 2007 (Revised May 2017) ASTM E 119 (UL 263) tests have been conducted on R-Control SIPs to develop fire resistance assemblies.
More informationSymphony II Adaptable Table System
Symphony II Adaptable Table System 1.00 General 1.01 Conditions 1.02 Scope of work 1. This section covers all materials, equipment, tools and labor for the supply and installation of the laboratory Symphony
More informationICC-ES Evaluation Report Reissued March 1, 2011 This report is subject to renewal in two years.
ICC-ES Evaluation Report www.icc-es.org (800) -6587 (56) 699-05 ESR-0 Reissued March, 0 This report is subject to renewal in two years. A Subsidiary of the International Code Council DIVISION: 06 00 00
More informationAF-4 Grooved Flange Adapter
SUBMITTAL INFORMATION PROJECT NAME: ENGINEER: CONTRACTOR: SPEC. SECTION: MEMBER FEATURES & ADVANTAGES Designed for connecting ANSI/AWWA C110/A21.10 and ASME/ANSI B16.1 Class 125/ flanged end components
More informationB2 Series Characterized Control Valve, Spring Return Actuator
Series Characterized Control Valve, Spring ctuator Two-way Valve with Stainless Steel all and Stem, NPT Female Ends Service: Flow Characteristic: Media Temp Range: Maximum Differential: Pressure ( P) mbient
More informationOVER THE RANGE MICROWAVE OVEN INSTALLATION INSTRUCTIONS
OVER THE RANGE MICROWAVE OVEN INSTALLATION INSTRUCTIONS Please read and save these installation instructions. MODEL NO.: DOTR12CWIV/DOTR12CBIV P/N: 3828W5U0202 YOUR SAFETY FIRST Read this entire manual
More informationSECTION HVAC DUCTS PART I - GENERAL 1.1 RELATED DOCUMENTS
SECTION 23 31 00 - HVAC DUCTS PART I - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationNX8 SERIES 6-1/4 HANDRAIL W/ VINYL HANDGRIP
6-1/4 HANDRAIL W/ VINYL HANDGRIP TYPICAL ASSEMBLY 5 2 BUTT JOINT 12 10 9 1 8 11 6 3 7 4 BUTT JOINT COMPONENT LIST 1 LEFT RETURN 7 UPPER IMPACT ABSORBER 2 RIGHT RETURN 8 LOWER IMPACT ABSORBER 3 OUTSIDE
More informationSDWH TIMBER-HEX Screw
Simpson Strong-Tie Fastening Systems Structural Wood-to-Wood Connections, Including Ledgers Double-barrier coating provides corrosion resistance equivalent to hot-dip galvanization, making it suitable
More informationBIKE FILE (301)
B IK E F I L E High Efficiency The Bike File is our most space efficient u-lock compatible product. Sturdy sliding hangers allow nine bikes to be securely stored in an eight-foot section while allowing
More informationPiping & Equipment Identification
Piping & Equipment Identification Part 1 General 1.01 Description of Work A. Work in this section includes: Identification materials, including necessary accessories indicated on Contract Documents and
More informationUL Selector and Submittal Generator User Guide
UL Selector and Submittal Generator User Guide 1 UL Selector and Submittal Generator User Guide The new Hilti UL System Selector and Firestop Submittal Generator tool is available on Hilti Online in the
More informationSECTION BULLET- RESISTANT DOORS
1 SECTION 08 3950 BULLET- RESISTANT DOORS PART 1- GENERAL 1.01 SUMMARY A. This Section Includes: 1. Bullet- resistant steel door and frame systems. 2. Door hardware for bullet- resistant steel door and
More information1.) Type: VL-F Single compartment rectangular smoke extraction ducts and fittings
1.) Type: VL-F Single compartment rectangular smoke extraction ducts and fittings 2.) Manufacturer / Place of manufacture: AEROPRODUKT Zrt., 6640 Csongrád, Szegedi út 1., HUNGARY 3.) Function: The smoke
More information