AutoCAD 2D-I. Module 1: Introduction to Drawing Tools. IAT Curriculum Unit PREPARED BY. January 2011

Size: px
Start display at page:

Download "AutoCAD 2D-I. Module 1: Introduction to Drawing Tools. IAT Curriculum Unit PREPARED BY. January 2011"

Transcription

1 AutoCAD 2D-I Module 1: Introduction to Drawing Tools PREPARED BY IAT Curriculum Unit January 2011 Institute of Applied Technology, 2011

2

3 Module 1: Introduction to Drawing Tools Module Objectives After the completion of this module, the student will be able to: Identify and describe the use of engineering drawing equipment Recognise different methods of laying out engineering drawing papers. Demonstrate the use of scales. Produce a simple drawing paper layout including border and title block. Module Contents 1 Introduction Drawing instruments Drawing Boards T-Square Set Square Pairs of Compasses Protractor Ruler Drawing pencils Eraser Circle template Drawing Paper Sizes of the drawing paper Scales Layout of the drawing paper Line type Technique of Lettering Activities Class Activities Homework... 8

4 1 Introduction Technical drawing is the study of the procedures, tools, supplies, skills and techniques used to record and communicate the shape and size of a product. Every product we have today (e.g. cars, houses, machines, etc ), began as an "idea" in some person's head. Before these "ideas" became products, they had to be drawn on paper so as to show what the idea looks like from different directions, Fig.1.1. Fig.1.1: Burj Al Arab- Dubai 2 Drawing instruments To prepare a drawing, one can use manual drafting instruments as shown in Fig.1.2, or computer-aided drafting (CAD). If the drawing is made without either manual instruments or CAD, it is called a freehand sketch. The following instruments are essential and should be available to produce a good quality technical drawing. Fig. 1.2: Manual Instruments. 2.1 Drawing Boards Drawing Boards can range from simple boards, like the one shown in Fig.1.3, to complicated drawing machines that would be used in engineering drawing office. The surface of the board should be dusted and smooth. Fig. 1.3: Drawing Board 2 Module 1: Introduction to drawing tools

5 2.2 T-Square T- Square is composed of a long strip, called the blade; it is placed on the drawing board and provides a constant horizontal edge. The T-square is shown in Fig.1.4. Fig. 1.4:T-Square 2.3 Set Square Set Squares are best made from transparent plastic. The two standard set squares that are commonly used are 30/60 and 45/45 degrees triangles as shown in Fig /45 triangle 30/60 triangle Fig. 1.5:Set Square 2.4 Pairs of Compasses There are basically two types of compasses 1. Pencil compasses which are used to draw circles. Circles up to 300 mm diameter are drawn using a large radius compass. 2. Spring bow compass which is used to draw circles of 50 mm diameter or less. (Fig.1.6). 2.5 Protractor Fig. 1.6:Compasses Protractors measure angles other than those obtained by the set squares and found in half circle or full circle types, Fig Fig.1.7: Protractors Module 1: Introduction to drawing tools 3

6 2.6 Ruler A 300 mm ruler with one edge marked in centimeters and millimeters is necessary, Fig.1.8. In a fully equipped drawing machine, horizontal and vertical rulers with graduations in mm or inches are attached to the drafting head. Fig.1.8: Ruler 2.7 Drawing pencils Pencils have nine grads of hardness from H to 9H and seven grades of softness from B to 7B as shown in Fig Fig.1.9: Pencil lead grades. 2.6 Eraser Erasers are available in different hardness and are used to erase pencil work. The common eraser used is a block-shaped vinyl eraser. (Fig.1.10). Fig.1.10: Eraser 2.8 Circle template Circle templates are useful for drawing small circles quickly and to join lines with a radius, A circle template is shown in Fig Fig.1.11: Circle template 4 Module 1: Introduction to drawing tools

7 3 Drawing Paper 3.1 Sizes of the drawing paper Drawing paper is available in A series, B series, and rolls of the International Organization for standardization (ISO), but series A is preferred. Paper sizes for series A are based on the A0 size, which has an area of 1 square meter. An A0 size sheet can be divided up evenly into the various other sizes (A1, A2, A3, A4 ) simply by halving the sheet on the long side in each case. As shown in Fig Fig. 1.12: Paper Sizes 3.2 Scales In order to produce drawing showing components in detail or as plans it is often necessary to use a scale. This can increase the size of the drawing in comparison to the real size of the component. Some of the recommended scales are listed below: Enlargements scales: 2:1 20:1 50:1 10:1 Full (same) size: 1:1 Reduction scales: 1:2 1:10 1:20 1: Layout of the drawing paper Drawing sheets of all sizes have standard layout. It is usual for each sheet to be provided with a drawing frame a short distance from the edge of the paper as shown in Fig Each drawing sheet has to be provided with a title block which represents the general information source for a drawing. It is normally placed in the bottom and at least contains the title of the drawing, the name of the draftsman, the scale, and the date. Module 1: Introduction to drawing tools 5

8 Drawing frame 15 BORDER Title block 100 NAME: TITLE: SECTION: DATE: SCALE 15 Fig 1.13: Layout of the drawing paper. 3.4 Line type Fig shows the types of line which are commonly used in engineering drawings such as visible lines, hidden lines, center lines, dimension lines, extension lines, and leader lines. Fig shows an application for the use of different types of lines. LINE Description Application Continous thick Continous thin Dashed thin Chain thin Visible outlines Dimension lines Projection lines Leader lines hatching Hidden outlines Circle center lines Fig.1.14: Line types and their description 6 Module 1: Introduction to drawing tools

9 130 HIDDEN UOTLINES (DASHED LINE) OUTLINE (CONTINOUS THICK) DIMENSTION LINE (CONTINOUS THIN) CENTER LINE (CHAIN THIN) Fig 1.15: The use of different line types in engineering drawing. 4 Technique of Lettering Printing increase the information that is provided on a drawing. Printing must be clear and neat so 5 that it is easy to read. Use guide lines 5 mm Fig. 1.16: Guide lines for apart as illustrated in Fig printing. These guide lines can be used to make sure that all letters and numbers have the same size. Always print using capital letters. All letters and numbers should touch the top and bottom guide lines. Guide lines should be 5 mm apart as explained earlier. An example for lettering technique is shown in Fig A B C D E F G H I J K L M N O P Q R S T U V W X Y Z Fig. 1.17: Printing numbers and letters. Module 1: Introduction to drawing tools 7

10 5 Activities 5.1 Class Activities Draw the objects shown below in full size using different drawing tools such as compasses, set squares and tee square. Use an A3 sheet to create the drawing with the same layout shown below. 1? R R15 R20 R15 80 R NAME: TITLE: SECTION: DATE: I.D.No. 5.2 Homework Draw the objects shown below in full size using different drawing tools such as compasses, set squares and tee square. Use an A4 sheet for each of the following objects 8 Module 1: Introduction to drawing tools

11 R Module 1: Introduction to drawing tools 9

12 Student notes 10 Module 1: Introduction to drawing tools

MISS. HANNA S CLASSROOM RULES

MISS. HANNA S CLASSROOM RULES MISS. HANNA S CLASSROOM RULES 1. My students never fail. I believe in you and so shall you! Miss. Hanna s Quote! 2. Come to class on time. 3. Bring a positive attitude. 4. Come prepared and bring your

More information

Engineering Graphics. Class 2 Drafting Instruments Mohammad Kilani

Engineering Graphics. Class 2 Drafting Instruments Mohammad Kilani Engineering Graphics Class 2 Drafting Instruments Mohammad Kilani Drafting Instruments A Design is as good as its instruments A engineering drawing is a highly stylized graphic representation of an idea.

More information

DRAWING INSTRUMENTS AND THEIR USES

DRAWING INSTRUMENTS AND THEIR USES Chapter - 1A DRAWING INSTRUMENTS AND THEIR USES Drawing Instruments are used to prepare neat and accurate Drawings. To a greater extent, the accuracy of the Drawings depend on the quality of instruments

More information

Chapter 1 Overview of an Engineering Drawing

Chapter 1 Overview of an Engineering Drawing Chapter 1 Overview of an Engineering Drawing TOPICS Graphics language Engineering drawing Projection methods Orthographic projection Drawing standards TOPICS Traditional Drawing Tools Lettering Freehand

More information

Chapter 1 Introduction

Chapter 1 Introduction Chapter 1 Introduction Contents Engineering drawing Drawing standards Drawing sheet Scale Lettering Line types Engineering Drawing Contents Engineering Drawing Effectiveness of Graphic Language 1. Try

More information

Introduction CHAPTER Graphics: A Tool to Communicate Ideas

Introduction CHAPTER Graphics: A Tool to Communicate Ideas CHAPTER 1 Introduction 1.1 Graphics: A Tool to Communicate Ideas Engineering graphics or drawing is the universal language of engineers. An engineer communicate his idea to others with the help of this

More information

Glass Box Projection. Gives you 6 sides to view of an object. 10/2/14 2

Glass Box Projection. Gives you 6 sides to view of an object. 10/2/14 2 2D Drawings Glass Box Projection Gives you 6 sides to view of an object. 10/2/14 2 We can simplify this for some objects to 3 views Glass Box Approach Glass Box Approach Glass Box Approach Glass Box Approach

More information

(As per New Revised Syllabus of Anna University) Department of Mechanical Engineering. SATHYABAMA UNIVERSITY Jeppiaar Nagar, Chennai

(As per New Revised Syllabus of Anna University) Department of Mechanical Engineering. SATHYABAMA UNIVERSITY Jeppiaar Nagar, Chennai (1*,1((5,1* *5$3+,&6 (As per New Revised Syllabus of Anna University) Dr. S.RAMACHANDRAN, M.E., Ph.D. Professor & Head K. PANDIAN, M.E., E.V.V.RAMANAMURTHY, M.Tech., R. DEVARAJ, M.E., Associate Professors

More information

Sketching in SciTech. What you need to know for graphic communication

Sketching in SciTech. What you need to know for graphic communication Sketching in SciTech What you need to know for graphic communication Sketching in your Logbook Use pencil Take up the WHOLE PAGE Label things 1. Proportion Each part of the sketch is the right size,

More information

Drafting Dictionary (Mechanical Board Drafting)

Drafting Dictionary (Mechanical Board Drafting) Description In this lesson the teacher will introduce the tools and equipment specific to board drafting. Board drafting (also known as manual drafting) refers to precision drawing with specialized instruments.

More information

Engineering Graphics- Basics.

Engineering Graphics- Basics. Engineering Graphics- Basics DRAWINGS: ( A Graphical Representation) The Fact about: If compared with Verbal or Written Description, Drawings offer far better idea about the Shape, Size & Appearance of

More information

Alphabet of Lines Chapter 3

Alphabet of Lines Chapter 3 Alphabet of Lines Chapter 3 Sacramento City College EDT 300/ ENGR 306 EDT 300/306 - Basic Technical Drafting 1 Alphabet of Lines The design industry has agreed on a set of standard lines that are used

More information

AABTKJX by Prentice Hall, Inc. A Pearson Company

AABTKJX by Prentice Hall, Inc. A Pearson Company Figure Number: 03-01 Page Number: Principal Items of Equipment. AABTKJX0 Figure Number: 03-02 Page Number: The T-square. AABTKJY0 Figure Number: 03-03 Page Number: Testing the Working Edge of the Drawing

More information

How to Design a Geometric Stained Glass Lamp Shade

How to Design a Geometric Stained Glass Lamp Shade This technique requires no calculation tables, math, or angle computation. Instead you can use paper & pencil with basic tech drawing skills to design any size or shape spherical lamp with any number of

More information

Scale and Dimensioning (Architectural Board Drafting)

Scale and Dimensioning (Architectural Board Drafting) Youth Explore Trades Skills Description In this activity, the teacher will first select an object that is larger than the page and scale it to fit in the designated drawing area to explain architectural

More information

Brief Introduction to Engineering Graphics The use of drawings to convey information. Sketching freehand straight edge

Brief Introduction to Engineering Graphics The use of drawings to convey information. Sketching freehand straight edge Brief Introduction to Engineering Graphics The use of drawings to convey information. Sketching freehand straight edge CAD drawings 2D drafting 3D model to 2D drawings 1 Different Graphical Representation

More information

GOAL Practise techniques for creating various types of geometric lines by constructing and reproducing figures. sheet of letter-sized white paper

GOAL Practise techniques for creating various types of geometric lines by constructing and reproducing figures. sheet of letter-sized white paper TECHNIQUE STUDENT BOOK Chapter 11, page 340 TOOLBOX Pages 62 67 GOAL Practise techniques for creating various types of geometric lines by constructing and reproducing figures. MATERIALS drawing board T-square

More information

ENGINEERING DRAWING INTRODUCTION

ENGINEERING DRAWING INTRODUCTION ENGINEERING DRAWING INTRODUCTION Drawing is the graphical language of engineers which is built upon certain basic principles and standards. A good drawing can be prepared making use of these principles

More information

3. The dimensioning SYMBOLS for arcs and circles should be given:

3. The dimensioning SYMBOLS for arcs and circles should be given: Draft Student Name: Teacher: District: Date: Wake County Test: 9_12 T and I IC61 - Drafting I Test 2 Description: 4.08 Dimensioning Form: 501 1. The MINIMUM amount of space between two, ADJACENT DIMENSION

More information

Graphic representation in technological projects

Graphic representation in technological projects 1st ESO: Technology, Programming and Robotics Graphic representation in technological projects Author: Guillermo Gómez Revision: Pablo Rivas Martín Contents 1 Prior knowledge... 2 2 Keywords... 2 3 Mindmap

More information

Unit 2.Drawing applied to technology

Unit 2.Drawing applied to technology Unit 2.Drawing applied to technology Unit 2.Drawing applied to technology What are we going to see in this unit? 2.1 Drawing tools and how to use them 2.2 Drafts and sketches 2.3 Scale 2.4 Diedric system:

More information

Optical Illusion Sketchbook Project Art 1201

Optical Illusion Sketchbook Project Art 1201 Optical Illusion Sketchbook Project Art 1201 Before beginning our final optical illusion project, we need to practice drawing optical illusions so we will have a better understanding of how to construct

More information

Isometric Drawing (Architectural Board drafting)

Isometric Drawing (Architectural Board drafting) Design and Drafting Description Isometric drawings use perspective to communicate a large amount of information in a single drawing. Isometric drawings show three sides of an object, making it easier to

More information

Student Name: Teacher: Date: District: Rowan. Assessment: 9_12 T and I IC61 - Drafting I Test 2. Description: Drafting 1 - Test 6.

Student Name: Teacher: Date: District: Rowan. Assessment: 9_12 T and I IC61 - Drafting I Test 2. Description: Drafting 1 - Test 6. Student Name: Teacher: Date: District: Rowan Assessment: 9_12 T and I IC61 - Drafting I Test 2 Description: Drafting 1 - Test 6 Form: 501 1. 2X on a hole note means: A. Double the size of the hole. B.

More information

CHAPTER 01 PRESENTATION OF TECHNICAL DRAWING. Prepared by: Sio Sreymean

CHAPTER 01 PRESENTATION OF TECHNICAL DRAWING. Prepared by: Sio Sreymean CHAPTER 01 PRESENTATION OF TECHNICAL DRAWING Prepared by: Sio Sreymean 2015-2016 Why do we need to study this subject? Effectiveness of Graphics Language 1. Try to write a description of this object. 2.

More information

ENGINEERING DRAWING LECTURE 4

ENGINEERING DRAWING LECTURE 4 ENGINEERING DRAWING LECTURE 4 Conventions Convention or Code: The representation of any matter by some sign or mark on the drawing is known as convention or code. The convention make the drawing simple

More information

ME 111: Engineering Drawing

ME 111: Engineering Drawing ME 111: Engineering Drawing Lecture # 01 Introduction For more detail, visit http://shilloi.iitg.ernet.in/~psr/ Indian Institute of Technology Guwahati Guwahati 781039 1 Syllabus 1. Importance of engineering

More information

AutoCAD 2D I. Module 16. Isometric and Dimensioning. IAT Curriculum Unit PREPARED BY. January 2011

AutoCAD 2D I. Module 16. Isometric and Dimensioning. IAT Curriculum Unit PREPARED BY. January 2011 AutoCAD 2D I Module 16 Isometric and Dimensioning PREPARED BY IAT Curriculum Unit January 2011 Institute of Applied Technology, 2011 Module 16 Auto CAD Self-paced Learning Modules AutoCAD 2D Isometric

More information

2. Line composed of closely and evenly spaced short dashes in a drawing represents

2. Line composed of closely and evenly spaced short dashes in a drawing represents 1. Hidden lines are drawn as (a) dashed narrow lines (b) dashed wide lines (c) long-dashed dotted wide line (d) long-dashed double dotted wide line Ans: (a) 2. Line composed of closely and evenly spaced

More information

DFTG 1305 UNIT 1. Semester: Spring 2016 Class #: Term: SS Instructor: Mays ALSabbagh

DFTG 1305 UNIT 1. Semester: Spring 2016 Class #: Term: SS Instructor: Mays ALSabbagh DFTG 1305 UNIT 1 Semester: Spring 2016 Class #: 94412 Term: SS Instructor: Mays ALSabbagh Technical Drafting Unit One: Introduction to Drafting Chapter 1 : The World Wide Graphic language for Design Lecture

More information

Production drawing Diagram. a) I am a freehand drawing that follows technical drawing standards.

Production drawing Diagram. a) I am a freehand drawing that follows technical drawing standards. THE TECHNOLOGICAL WORLD Graphical language STUDENT BOOK Ch. 11, pp. 336 342 Basic lines, geometric lines, sketches 1. In technology, the two most widely used types of technical drawings are: a) sketch

More information

Technical English -I 4 th week ENGINEERING DRAWING

Technical English -I 4 th week ENGINEERING DRAWING Technical English -I 4 th week ENGINEERING DRAWING What is engineering drawing? It is the art of representation of geometrical objects on a drawing sheet. An engineering drawing is used to fully and clearly

More information

Fundamentals for building Drawing

Fundamentals for building Drawing Fundamentals for building Drawing What is Drawing Introduction Knowledge of preparing and understanding drawing will prove to be an invaluable aid while performing their jobs effectively, efficiently.

More information

UNIT Lines and Symbols

UNIT Lines and Symbols 3 UNIT Lines and Symbols Various lines on a drawing have different meanings. They may appear solid, broken, thick, or thin. Each is designed to help the blueprint reader make an interpretation. The standards

More information

Sketching Fundamentals

Sketching Fundamentals Sketching Fundamentals Learning Outcome When you complete this module you will be able to: Make basic engineering sketches of plant equipment. Learning Objectives Here is what you will be able to do when

More information

Chapter 6. Architectural Lines and Lettering

Chapter 6. Architectural Lines and Lettering Chapter 6 Architectural Lines and Lettering Drafting Introduction Universal graphic language Uses lines, symbols, dimensions, and notes to describe a structure to be built Properly drawn lines are dark,

More information

ARCHITECTURAL DESIGN (542)

ARCHITECTURAL DESIGN (542) DESCRIPTION This is the first assessment in a sequence, Architectural Design I prepares students with knowledge of residential architectural and related construction. Topics include; architectural blueprint

More information

Chapter 1 Overview of a Technical Drawing

Chapter 1 Overview of a Technical Drawing Chapter 1 Overview of a Technical Drawing TOPICS Graphics language Engineering drawing Projection methods Orthographic projection Drawing standards TOPICS Traditional Drawing Tools Lettering Dimensioning

More information

2004 Academic Challenge

2004 Academic Challenge 2004 Academic Challenge ENGINEERING GRAPHICS TEST - REGIONAL Engineering Graphics Test Production Team Ryan Brown, Illinois State University Author/Team Coordinator Kevin Devine, Illinois State University

More information

1.- Graphic materials

1.- Graphic materials 1.- Graphic materials We use different tools for drawing. The choice depends on the type of drawing we want to do. Pencils: Pencils have a wooden case with a lead inside made of graphite and clay. Types

More information

Drawing sheet: - The various size of the drawing sheet used for engineering drawing as per IS Are listed in the table

Drawing sheet: - The various size of the drawing sheet used for engineering drawing as per IS Are listed in the table Dronacharya Group of Institutions, Greater Noida Computer Aided Engineering Graphics (CAEG) (NCE 151/251) List of Drawing Sheets: 1. Letter writing & Dimensioning. 2. Projection of Points & Lines. 3. Projection

More information

Civil Engineering Drawing

Civil Engineering Drawing Civil Engineering Drawing Third Angle Projection In third angle projection, front view is always drawn at the bottom, top view just above the front view, and end view, is drawn on that side of the front

More information

technical drawing school of art, design and architecture nust spring 2011

technical drawing school of art, design and architecture nust spring 2011 technical drawing school of art, design and architecture nust spring 2011 http://www.youtube.com/watch?v=e55ocgb0l8o t e c h n i c a l d r a w i n g a mean to design reasoning spring 2011 the ability to

More information

Two-Dimensional Drawing

Two-Dimensional Drawing 22 Chapter Cxxxx 40757 3/19/08 10:24 AM Page 1 7% 3% 3% 18% 20% 22 Chapter CXXXX 40757 Page 1 03/18/08 MD 22 Two-Dimensional Drawing objectives After completing this chapter, you should be able to Identify

More information

INTRODUCTION to CAD ACAD BASICS. 2.1 Starting with ACAD. 2.2 Layout and sketching. 2.3 Drawing environment. 2.4 Elements of drawing

INTRODUCTION to CAD ACAD BASICS. 2.1 Starting with ACAD. 2.2 Layout and sketching. 2.3 Drawing environment. 2.4 Elements of drawing INTRODUCTION to CAD ACAD BASICS 2.1 Starting with ACAD 2.2 Layout and sketching 2.3 Drawing environment 2.4 Elements of drawing 2.4.1 Draw commands 2.5 3D functions 2.6 Starting the drawing 2.6.1 Drawing

More information

Student Name: Teacher: Date: District: Rowan. Assessment: 9_12 T and I IC61 - Drafting I Test 1. Description: Unit C - Sketching - Test 2.

Student Name: Teacher: Date: District: Rowan. Assessment: 9_12 T and I IC61 - Drafting I Test 1. Description: Unit C - Sketching - Test 2. Student Name: Teacher: Date: District: Rowan Assessment: 9_12 T and I IC61 - Drafting I Test 1 Description: Unit C - Sketching - Test 2 Form: 501 1. The most often used combination of views includes the:

More information

Planning and Designing Projects

Planning and Designing Projects Lesson A3 1 Planning and Designing Projects Unit A. Mechanical Systems and Technology Problem Area 3. Construction Systems Lesson 1. Planning and Designing Projects Content/Process Statement: ACS10 Core

More information

Mechanical Drawing. Unit 2 Study Guide for Chapters 6-10

Mechanical Drawing. Unit 2 Study Guide for Chapters 6-10 Mechanical Drawing Unit 2 Study Guide for Chapters 6-10 Chapter 6 Multiview Drawing Section 6.1 Understanding Orthographic Projection A. Technical Drawing: How can a technical drawing give more accurate

More information

Engineering Working Drawings Basics

Engineering Working Drawings Basics Engineering Working Drawings Basics Engineering graphics is an effective way of communicating technical ideas and it is an essential tool in engineering design where most of the design process is graphically

More information

UNIT 1 SIMILARITY, CONGRUENCE, AND PROOFS Lesson 2: Constructing Lines, Segments, and Angles Instruction

UNIT 1 SIMILARITY, CONGRUENCE, AND PROOFS Lesson 2: Constructing Lines, Segments, and Angles Instruction Prerequisite Skills This lesson requires the use of the following skills: using a compass understanding the geometry terms line, segment, ray, and angle Introduction Two basic instruments used in geometry

More information

ENGINEERING DRAWING. 1. Set squares are used to draw different angles. What is the angel a formed by the 45⁰ set square? Give a brief answer.

ENGINEERING DRAWING. 1. Set squares are used to draw different angles. What is the angel a formed by the 45⁰ set square? Give a brief answer. ENGINEERING DRAWING 1. Set squares are used to draw different angles. What is the angel a formed by the 45⁰ set square? Give a brief answer. 2. Which is the correct method of hatching a plane surface?

More information

- 9_12TI7921-QUIZ2 - Print Test. 1. The BEST media for mechanical drawing isbest media for mechanical drawing is: (NCCTE.9_12.TI

- 9_12TI7921-QUIZ2 - Print Test. 1. The BEST media for mechanical drawing isbest media for mechanical drawing is: (NCCTE.9_12.TI Page 1 of 7 Report: Test nswer Key istrict: Madison Test: escription: Unit-S-Tools Form: 501 1. The EST media for mechanical drawing isest media for mechanical drawing is: (NTE.9_12.TI.7921.003.01) 2.

More information

Orthographic Drawing (Architectural Board Drafting)

Orthographic Drawing (Architectural Board Drafting) Design and Drafting Description In this activity, the teacher will introduce orthographic projection, in which a multi-view drawing shows how the sides of an object are related to each another. Students

More information

Pictorial Drawings. DFTG-1305 Technical Drafting Prepared by Francis Ha, Instructor

Pictorial Drawings. DFTG-1305 Technical Drafting Prepared by Francis Ha, Instructor DFTG-1305 Technical Drafting Prepared by Francis Ha, Instructor Pictorial Drawings Geisecke s textbook for reference: 14 th Ed. Ch. 15: p. 601 Ch. 16: p. 620 15 th Ed. Ch. 14: p. 518 Ch. 15: p. 552 Update:

More information

Multi-View Drawing Review

Multi-View Drawing Review Multi-View Drawing Review Sacramento City College EDT 300/ENGR 306 EDT 300 / ENGR 306 - Chapter 5 1 Objectives Identify and select the various views of an object. Determine the number of views needed to

More information

Technology Education Grades Drafting I

Technology Education Grades Drafting I Technology Education Grades 9-12 Drafting I 46 Grade Level: 9, 10, 11, 12 Technology Education, Grades 9-12 Drafting I Prerequisite: None Drafting I is an elective course which provides students the opportunity

More information

Chapter 8. Technical Drawings

Chapter 8. Technical Drawings Chapter 8 Technical Drawing Technical Drawings Multiview drawings Also called three-view drawings Simple objects take three views Front, top, one side Title block Identifies who did the design Gives date,

More information

1: Assemblage & Hierarchy

1: Assemblage & Hierarchy What: 1: Assemblage & Hierarchy 2 compositional sequences o abstract, line compositions based on a 9 square grid o one symmetrical o one asymmetrical Step 1: Collage Step 2: Additional lines Step 3: Hierarchy

More information

2003 Academic Challenge

2003 Academic Challenge Worldwide Youth in Science and Engineering 2003 Academic Challenge ENGINEERING GRAPHICS TEST - REGIONAL Engineering Graphics Test Production Team Ryan Brown, Illinois State University Author/Team Coordinator

More information

Multiview Drawing. Definition: Graphical representation of a 3- dimensional object on one plane (sheet of paper) using two or more views.

Multiview Drawing. Definition: Graphical representation of a 3- dimensional object on one plane (sheet of paper) using two or more views. Multiview Drawing Definition: Graphical representation of a 3- dimensional object on one plane (sheet of paper) using two or more views. Multiview Drawing Another name for multiview drawing is orthographic

More information

Technical Drawing 101 with AutoCAD 2018

Technical Drawing 101 with AutoCAD 2018 Technical Drawing 101 with AutoCAD 2018 A Multidisciplinary Guide to Drafting Theory and Practice with Video Instruction Douglas Smith Antonio Ramirez Ashleigh Fuller SDC PUBLICATIONS Better Textbooks.

More information

TECHNICAL DESIGN I (540)

TECHNICAL DESIGN I (540) DESCRIPTION The first assessment in a series, Technical Design I prepares students to develop technical knowledge and skills required to plan and prepare scale pictorial interpretations of engineering

More information

Leaving Certificate Technology

Leaving Certificate Technology Leaving Certificate Technology Core Module Resource: Communications and Graphics Media Communications and Graphics Media Resource Document Material and Layout Range of tasks exploring topics and learning

More information

Interpretation of Drawings. An Introduction to the Basic Concepts of Creating Technical Drawings

Interpretation of Drawings. An Introduction to the Basic Concepts of Creating Technical Drawings Interpretation of Drawings An Introduction to the Basic Concepts of Creating Technical Drawings Introduction In the design process drawings are the main way in which information about an object or product

More information

60 Most Important Engineering Drawing Questions

60 Most Important Engineering Drawing Questions 1. If a client of yours is having difficulty visualizing a design, what type of drawing would be the easiest to understand? A. axonometric B. three-view orthographic C. one-view orthographic D. bimetric

More information

Beginning Engineering Graphics 3 rd Week Lecture Notes Instructor: Edward N. Locke Topic: The Coordinate System, Types of Drawings and Orthographic

Beginning Engineering Graphics 3 rd Week Lecture Notes Instructor: Edward N. Locke Topic: The Coordinate System, Types of Drawings and Orthographic Beginning Engineering Graphics 3 rd Week Lecture Notes Instructor: Edward N. Locke Topic: The Coordinate System, Types of Drawings and Orthographic 1 st Subject: The Cartesian Coordinate System The Cartesian

More information

You will need 9x12 blue construction paper, SOFT LEAD pencil colors, an eraser, and a metric ruler.

You will need 9x12 blue construction paper, SOFT LEAD pencil colors, an eraser, and a metric ruler. Here is a nice picture for a beginner to start using color. This is a copy of the black and white barn drawing so if you wish you can do that one first. Scroll down. You will need 9x12 blue construction

More information

Creating another Printed Circuit Board

Creating another Printed Circuit Board Appendix C Creating another Printed Circuit Board In this chapter, we will learn the following to World Class standards: Starting with a Finished Schematic Creating the Layers for the Printed Circuit Board

More information

Standards of Learning Guided Practice Suggestions. For use with the Mathematics Tools Practice in TestNav TM 8

Standards of Learning Guided Practice Suggestions. For use with the Mathematics Tools Practice in TestNav TM 8 Standards of Learning Guided Practice Suggestions For use with the Mathematics Tools Practice in TestNav TM 8 Table of Contents Change Log... 2 Introduction to TestNav TM 8: MC/TEI Document... 3 Guided

More information

80 ` AutoCAD 2D I. Module 7. Drawing Lines Using Polar Coordinates PREPARED BY. IAT Curriculum Unit. February 2011

80 ` AutoCAD 2D I. Module 7. Drawing Lines Using Polar Coordinates PREPARED BY. IAT Curriculum Unit. February 2011 80 ` AutoCAD 2D I Module 7 Drawing Lines Using Polar Coordinates PREPARED BY IAT Curriculum Unit February 2011 Institute of Applied Technology, 2011 Module 7 Auto CAD Self-paced Learning Modules AutoCAD

More information

Copyrighted Material. Copyrighted Material. Copyrighted. Copyrighted. Material

Copyrighted Material. Copyrighted Material. Copyrighted. Copyrighted. Material Engineering Graphics ORTHOGRAPHIC PROJECTION People who work with drawings develop the ability to look at lines on paper or on a computer screen and "see" the shapes of the objects the lines represent.

More information

COURSE: INTRODUCTION TO CAD GRADES: UNIT: Measurement

COURSE: INTRODUCTION TO CAD GRADES: UNIT: Measurement UNIT: Measurement - Students will demonstrate correctness in measuring using various scales and instruments. Demonstrate the various marks that make up a ruler including 1/16, 1/8, ¼ and ½. Assessment

More information

CE 100 Civil Engineering Drawing Sessional (Lab Manual)

CE 100 Civil Engineering Drawing Sessional (Lab Manual) CE 100 Civil Engineering Drawing Sessional (Lab Manual) Department of Civil Engineering Ahsanullah University of Science and Technology November, 2017 1 Preface This course is designed to provide civil

More information

Activity 5.2 Making Sketches in CAD

Activity 5.2 Making Sketches in CAD Activity 5.2 Making Sketches in CAD Introduction It would be great if computer systems were advanced enough to take a mental image of an object, such as the thought of a sports car, and instantly generate

More information

Op Art Pinwheel Side 1 Choices

Op Art Pinwheel Side 1 Choices Op Art Pinwheel Side 1 Choices 1. 1) Draw an X from corner to corner. Then draw a vertical line and horizontal line that match up in the center. 2) draw curved lines, spaced about 1/2" apart, between the

More information

Chapter 5 SECTIONS OF SOLIDS 5.1 INTRODUCTION

Chapter 5 SECTIONS OF SOLIDS 5.1 INTRODUCTION Chapter 5 SECTIONS OF SOLIDS 5.1 INTRODUCTION We have studied about the orthographic projections in which a 3 dimensional object is detailed in 2-dimension. These objects are simple. In engineering most

More information

WAYNESBORO AREA SCHOOL DISTRICT CURRICULUM INTRODUCTION TO ENGINEERING

WAYNESBORO AREA SCHOOL DISTRICT CURRICULUM INTRODUCTION TO ENGINEERING UNIT: Classroom rules and procedures NO. OF DAYS: 2 KEY LEARNING(S): Expectations and classroom procedures UNIT : What are the expectations and classroom procedures in the CAD room 3.4.12.A3. Demonstrate

More information

Assignment 12 CAD Mechanical Part 2

Assignment 12 CAD Mechanical Part 2 Assignment 12 CAD Mechanical Part 2 Objectives In this assignment you will learn to apply the hidden lines, isometric snap, and ellipses commands along with commands previously learned.. General Hidden

More information

Drawing: technical drawing TECHNOLOGY

Drawing: technical drawing TECHNOLOGY Drawing: technical drawing Introduction Humans have always used images to communicate. Cave paintings, some of which are over 40,000 years old, are the earliest example of this artistic form of communication.

More information

GUIDELINES FOR DRAFTING

GUIDELINES FOR DRAFTING UNIT 1 GUIDELINES FOR DRAFTING 1.1 Introduction The term draughting is used to describe the language of drafting in this book. It defines the terminology, symbology, conventions, and standards used in

More information

RAKESH JALLA B.Tech. (ME), M. Tech. (CAD/CAM) Assistant Professor, Department Of Mechanical Engineering, CMR Institute of Technology. Introduction to Engineering Drawing Principles of Engineering Drawing/Graphics:

More information

Dimensioning the Rectangular Problem

Dimensioning the Rectangular Problem C h a p t e r 3 Dimensioning the Rectangular Problem In this chapter, you will learn the following to World Class standards: 1. Creating new layers in an AutoCAD drawing 2. Placing Centerlines on the drawing

More information

Drawing a Living Room and Family Room Floorplan

Drawing a Living Room and Family Room Floorplan Appendix C Drawing a Living Room and Family Room Floorplan In this chapter, you will learn the following to World Class standards: Draw a Living Room and Family Room Floorplan Draw the Walls and Stairs

More information

Study Unit. Auxiliary Views. This sneak preview of your study material has been prepared in advance of the book's actual online release.

Study Unit. Auxiliary Views. This sneak preview of your study material has been prepared in advance of the book's actual online release. Study Unit Auxiliary Views This sneak preview of your study material has been prepared in advance of the book's actual online release. iii Preview You re entering now into another subject area in your

More information

MEM09003B Prepare basic engineering drawing

MEM09003B Prepare basic engineering drawing MEM0 Metal and Engineering Training Package MEM0900B Prepare basic engineering drawing Learner guide Version Training and Education Support Industry Skills Unit Meadowbank Product code: 6 Acknowledgement

More information

Grade 2 Mathematics Scope and Sequence

Grade 2 Mathematics Scope and Sequence Grade 2 Mathematics Scope and Sequence Common Core Standards 2.OA.1 I Can Statements Curriculum Materials & (Knowledge & Skills) Resources /Comments Sums and Differences to 20: (Module 1 Engage NY) 100

More information

TITLE DATE PERIOD YOUR NAME

TITLE DATE PERIOD YOUR NAME Step A. Line up paper up with T-Square and tape down corners. Border Lines and Title Block Step B. Measure in from each edge.2. Draw in border lines. Step C. Measure up from bottom border line.1,.2 and

More information

Sec Geometry - Constructions

Sec Geometry - Constructions Sec 2.2 - Geometry - Constructions Name: 1. [COPY SEGMENT] Construct a segment with an endpoint of C and congruent to the segment AB. A B C **Using a ruler measure the two lengths to make sure they have

More information

Grade 7 Mathematics Item Specifications Florida Standards Assessments

Grade 7 Mathematics Item Specifications Florida Standards Assessments Assessment Limit MAFS7.G.1 Draw, construct, and describe geometrical figures and describe the relationships between them. MAFS.7.G.1.1 Solve problems involving scale drawings of geometric figures, including

More information

INTERMEDIATE LEVEL MEASUREMENT

INTERMEDIATE LEVEL MEASUREMENT INTERMEDIATE LEVEL MEASUREMENT TABLE OF CONTENTS Format & Background Information...3-6 Learning Experience 1- Getting Started...6-7 Learning Experience 2 - Cube and Rectangular Prisms...8 Learning Experience

More information

Drawing Daisy Wheel Angles and Triangles

Drawing Daisy Wheel Angles and Triangles Drawing Daisy Wheel Angles and Triangles Laurie Smith Laurie Smith is an independent early-building design researcher, specialising in geometrical design systems. Because geometry was part of the medieval

More information

(Ans:d) a. A0 b. A1 c. A2 d. A3. (Ans:b) (Ans:a) (Ans:d) (Ans:d)

(Ans:d) a. A0 b. A1 c. A2 d. A3. (Ans:b) (Ans:a) (Ans:d) (Ans:d) Multiple Choice Questions (MCQ) on Engineering Drawing (Instruments) The mini drafter serves the purpose of everything except a. Scales b. Set square c. Protractor d. Compass (Ans:d) During operation,

More information

Mathematical Construction

Mathematical Construction Mathematical Construction Full illustrated instructions for the two bisectors: Perpendicular bisector Angle bisector Full illustrated instructions for the three triangles: ASA SAS SSS Note: These documents

More information

ENGINEERING GRAPHICS 1.0 Introduction Engineering Graphics Drawing as an art Artist Graphic design Engineering graphics engineering drawing

ENGINEERING GRAPHICS 1.0 Introduction Engineering Graphics Drawing as an art Artist Graphic design Engineering graphics engineering drawing ENGINEERING GRAPHICS 1.0 Introduction Engineering is the profession in which the knowledge of mathematics and science gained by study, experience and practice is applied with good judgment to develop a

More information

2012 Academic Challenge

2012 Academic Challenge 2012 Academic Challenge ENGINEERING GRAPHICS TEST STATE FINAL This Test Consists of 40 Questions Engineering Graphics Test Production Team Ryan Brown, Illinois State University Author/Team Leader Jacob

More information

Engineering Graphics & Technology. NQF Level 2. Sparrow Consulting LECTURER S GUIDE TVET FIRST

Engineering Graphics & Technology. NQF Level 2. Sparrow Consulting LECTURER S GUIDE TVET FIRST Engineering Graphics & Technology NQF Level 2 Sparrow Consulting LECTURER S GUIDE TVET FIRST Engineering Graphics & Technology NQF Level 2 Lecturer s Guide M Conradie Engineering Graphics & Technology

More information

the same information given in two different 1. Dimensions should NOT be duplicated, or Dimension Guidelines Incorrect ways.

the same information given in two different 1. Dimensions should NOT be duplicated, or Dimension Guidelines Incorrect ways. Dimension Guidelines 1. Dimensions should NOT be duplicated, or the same information given in two different ways. Incorrect 1. Dimensions should NOT be duplicated, or the same information given in two

More information

Constructions. Unit 9 Lesson 7

Constructions. Unit 9 Lesson 7 Constructions Unit 9 Lesson 7 CONSTRUCTIONS Students will be able to: Understand the meanings of Constructions Key Vocabulary: Constructions Tools of Constructions Basic geometric constructions CONSTRUCTIONS

More information

Cartoon Faces for Family Portrait

Cartoon Faces for Family Portrait Cartoon Faces for Family Portrait in Windows Paint Make nice cartoon portraits of the child and her/his family for a page of the book. Make one head & shoulders portrait for each family member. Then arrange

More information